[PATCH 00/26] Add support for AR9485

[PATCH 00/26] Add support for AR9485

[Vasanthakumar Thiagarajan]

John,

	This patch series add support for a new chipset of AR9003 family.
This chip(AR9485) is an 1x1 and 2.4Ghz band only.

Vasanth

Vasanthakumar Thiagarajan (26):
  ath9k_hw: Define hw version macros for AR9485
  ath9k_hw: Add initvals.h for AR9485
  ath9k_hw: Enable hw initialization for AR9485
  ath9k_hw: Initialize mode registers for AR9485
  ath9k_hw: Initialize tx/rx gain table from initvals.h for AR9485
  ath9k_hw: Eeeprom changes for AR9485
  ath9k_hw: Disable LDPC for AR9485
  ath9k: Disable TX STBC for AR9485
  ath9k: Enable extended synch for AR9485 to fix L0s recovery issue
  ath9k: Configure pll control for AR9485
  ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 from an array for
    AR9485
  ath9k_hw: Add a helper function to get spur channel pointer from cal
    data for AR9003 family
  ath9k: Read spur channel information from eeprom for AR9485
  ath9k_hw: Configure xpa bias level for AR9485
  ath9k_hw: Read and configure antenna diversity control for AR9485
  ath9k_hw: Configure attenuation control only for chain 0 on AR9485
  ath9k_hw: Configure internal regulator for AR9485
  ath9k_hw: Read and configure turnning caps to regulate freq accuracy
  ath9k_hw: Configure power control only for chain 0 on AR9485
  ath9k_hw: Program appropriate chianmask for AR9485 before starting
    AGC/IQ cal
  ath9k_hw: Define IQcal correction coefficient registers using index
  ath9k_hw: Add IQ cal changes for AR9485
  ath9k_hw: Program appropriate register for temperature compensation
    cal for AR9485
  ath9k_hw: Setup paprd only for chain 0 on AR9485
  ath9k_hw: Disable MRC CCK for AR9485
  ath9k: Add device id of AR9485 to pci table

 drivers/net/wireless/ath/ath.h                   |    1 +
 drivers/net/wireless/ath/ath9k/ani.c             |    2 +-
 drivers/net/wireless/ath/ath9k/ar9003_calib.c    |  256 ++++++-
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c   |  193 ++++-
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.h   |    2 +
 drivers/net/wireless/ath/ath9k/ar9003_hw.c       |  278 +++++--
 drivers/net/wireless/ath/ath9k/ar9003_paprd.c    |   40 +-
 drivers/net/wireless/ath/ath9k/ar9003_phy.c      |   76 ++-
 drivers/net/wireless/ath/ath9k/ar9003_phy.h      |   70 ++-
 drivers/net/wireless/ath/ath9k/ar9485_initvals.h |  943 ++++++++++++++++++++++
 drivers/net/wireless/ath/ath9k/hw.c              |   19 +-
 drivers/net/wireless/ath/ath9k/hw.h              |    3 +
 drivers/net/wireless/ath/ath9k/init.c            |    4 +-
 drivers/net/wireless/ath/ath9k/main.c            |    3 +
 drivers/net/wireless/ath/ath9k/pci.c             |   13 +
 drivers/net/wireless/ath/ath9k/reg.h             |   10 +
 16 files changed, 1745 insertions(+), 168 deletions(-)
 create mode 100644 drivers/net/wireless/ath/ath9k/ar9485_initvals.h

[PATCH 01/26] ath9k_hw: Define hw version macros for AR9485

[Vasanthakumar Thiagarajan]

AR9485 is a single chain and single band (2.4 Ghz) chip.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/reg.h |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/reg.h b/drivers/net/wireless/ath/ath9k/reg.h
index c2472ed..0153ba1 100644
--- a/drivers/net/wireless/ath/ath9k/reg.h
+++ b/drivers/net/wireless/ath/ath9k/reg.h
@@ -787,6 +787,8 @@
 #define AR_SREV_REVISION_9271_11	1
 #define AR_SREV_VERSION_9300		0x1c0
 #define AR_SREV_REVISION_9300_20	2 /* 2.0 and 2.1 */
+#define AR_SREV_VERSION_9485		0x240
+#define AR_SREV_REVISION_9485_10	0
 
 #define AR_SREV_5416(_ah) \
 	(((_ah)->hw_version.macVersion == AR_SREV_VERSION_5416_PCI) || \
@@ -859,6 +861,12 @@
 	 (((_ah)->hw_version.macVersion == AR_SREV_VERSION_9300) && \
 	  ((_ah)->hw_version.macRev >= AR_SREV_REVISION_9300_20)))
 
+#define AR_SREV_9485(_ah) \
+	(((_ah)->hw_version.macVersion == AR_SREV_VERSION_9485))
+#define AR_SREV_9485_10(_ah) \
+	(AR_SREV_9485(_ah) && \
+	 ((_ah)->hw_version.macRev == AR_SREV_REVISION_9485_10))
+
 #define AR_SREV_9285E_20(_ah) \
     (AR_SREV_9285_12_OR_LATER(_ah) && \
      ((REG_READ(_ah, AR_AN_SYNTH9) & 0x7) == 0x1))
-- 
1.7.0.4

[PATCH 02/26] ath9k_hw: Add initvals.h for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9485_initvals.h |  943 ++++++++++++++++++++++
 1 files changed, 943 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/wireless/ath/ath9k/ar9485_initvals.h

diff --git a/drivers/net/wireless/ath/ath9k/ar9485_initvals.h b/drivers/net/wireless/ath/ath9k/ar9485_initvals.h
new file mode 100644
index 0000000..70de3d8
--- /dev/null
+++ b/drivers/net/wireless/ath/ath9k/ar9485_initvals.h
@@ -0,0 +1,943 @@
+/*
+ * Copyright (c) 2010 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef INITVALS_9485_H
+#define INITVALS_9485_H
+
+static const u32 ar9485Common_1_0[][2] = {
+	/*   Addr     allmodes */
+	{0x00007010, 0x00000022},
+	{0x00007020, 0x00000000},
+	{0x00007034, 0x00000002},
+	{0x00007038, 0x000004c2},
+};
+
+static const u32 ar9485_1_0_mac_postamble[][5] = {
+	/* Addr     5G_HT20     5G_HT40     2G_HT40     2G_HT20    */
+	{0x00001030, 0x00000230, 0x00000460, 0x000002c0, 0x00000160},
+	{0x00001070, 0x00000168, 0x000002d0, 0x00000318, 0x0000018c},
+	{0x000010b0, 0x00000e60, 0x00001cc0, 0x00007c70, 0x00003e38},
+	{0x00008014, 0x03e803e8, 0x07d007d0, 0x10801600, 0x08400b00},
+	{0x0000801c, 0x128d8027, 0x128d804f, 0x12e00057, 0x12e0002b},
+	{0x00008120, 0x08f04800, 0x08f04800, 0x08f04810, 0x08f04810},
+	{0x000081d0, 0x00003210, 0x00003210, 0x0000320a, 0x0000320a},
+	{0x00008318, 0x00003e80, 0x00007d00, 0x00006880, 0x00003440},
+};
+
+static const u32 ar9485_1_0_pcie_phy_pll_on_clkreq_disable_L1[][2] = {
+	/*   Addr     allmodes */
+	{0x00018c00, 0x10212e5e},
+	{0x00018c04, 0x000801d8},
+	{0x00018c08, 0x0000580c},
+};
+
+static const u32 ar9485Common_wo_xlna_rx_gain_1_0[][2] = {
+	/*   Addr     allmodes */
+	{0x0000a000, 0x00010000},
+	{0x0000a004, 0x00030002},
+	{0x0000a008, 0x00050004},
+	{0x0000a00c, 0x00810080},
+	{0x0000a010, 0x01800082},
+	{0x0000a014, 0x01820181},
+	{0x0000a018, 0x01840183},
+	{0x0000a01c, 0x01880185},
+	{0x0000a020, 0x018a0189},
+	{0x0000a024, 0x02850284},
+	{0x0000a028, 0x02890288},
+	{0x0000a02c, 0x03850384},
+	{0x0000a030, 0x03890388},
+	{0x0000a034, 0x038b038a},
+	{0x0000a038, 0x038d038c},
+	{0x0000a03c, 0x03910390},
+	{0x0000a040, 0x03930392},
+	{0x0000a044, 0x03950394},
+	{0x0000a048, 0x00000396},
+	{0x0000a04c, 0x00000000},
+	{0x0000a050, 0x00000000},
+	{0x0000a054, 0x00000000},
+	{0x0000a058, 0x00000000},
+	{0x0000a05c, 0x00000000},
+	{0x0000a060, 0x00000000},
+	{0x0000a064, 0x00000000},
+	{0x0000a068, 0x00000000},
+	{0x0000a06c, 0x00000000},
+	{0x0000a070, 0x00000000},
+	{0x0000a074, 0x00000000},
+	{0x0000a078, 0x00000000},
+	{0x0000a07c, 0x00000000},
+	{0x0000a080, 0x28282828},
+	{0x0000a084, 0x28282828},
+	{0x0000a088, 0x28282828},
+	{0x0000a08c, 0x28282828},
+	{0x0000a090, 0x28282828},
+	{0x0000a094, 0x21212128},
+	{0x0000a098, 0x171c1c1c},
+	{0x0000a09c, 0x02020212},
+	{0x0000a0a0, 0x00000202},
+	{0x0000a0a4, 0x00000000},
+	{0x0000a0a8, 0x00000000},
+	{0x0000a0ac, 0x00000000},
+	{0x0000a0b0, 0x00000000},
+	{0x0000a0b4, 0x00000000},
+	{0x0000a0b8, 0x00000000},
+	{0x0000a0bc, 0x00000000},
+	{0x0000a0c0, 0x001f0000},
+	{0x0000a0c4, 0x111f1100},
+	{0x0000a0c8, 0x111d111e},
+	{0x0000a0cc, 0x111b111c},
+	{0x0000a0d0, 0x22032204},
+	{0x0000a0d4, 0x22012202},
+	{0x0000a0d8, 0x221f2200},
+	{0x0000a0dc, 0x221d221e},
+	{0x0000a0e0, 0x33013302},
+	{0x0000a0e4, 0x331f3300},
+	{0x0000a0e8, 0x4402331e},
+	{0x0000a0ec, 0x44004401},
+	{0x0000a0f0, 0x441e441f},
+	{0x0000a0f4, 0x55015502},
+	{0x0000a0f8, 0x551f5500},
+	{0x0000a0fc, 0x6602551e},
+	{0x0000a100, 0x66006601},
+	{0x0000a104, 0x661e661f},
+	{0x0000a108, 0x7703661d},
+	{0x0000a10c, 0x77017702},
+	{0x0000a110, 0x00007700},
+	{0x0000a114, 0x00000000},
+	{0x0000a118, 0x00000000},
+	{0x0000a11c, 0x00000000},
+	{0x0000a120, 0x00000000},
+	{0x0000a124, 0x00000000},
+	{0x0000a128, 0x00000000},
+	{0x0000a12c, 0x00000000},
+	{0x0000a130, 0x00000000},
+	{0x0000a134, 0x00000000},
+	{0x0000a138, 0x00000000},
+	{0x0000a13c, 0x00000000},
+	{0x0000a140, 0x001f0000},
+	{0x0000a144, 0x111f1100},
+	{0x0000a148, 0x111d111e},
+	{0x0000a14c, 0x111b111c},
+	{0x0000a150, 0x22032204},
+	{0x0000a154, 0x22012202},
+	{0x0000a158, 0x221f2200},
+	{0x0000a15c, 0x221d221e},
+	{0x0000a160, 0x33013302},
+	{0x0000a164, 0x331f3300},
+	{0x0000a168, 0x4402331e},
+	{0x0000a16c, 0x44004401},
+	{0x0000a170, 0x441e441f},
+	{0x0000a174, 0x55015502},
+	{0x0000a178, 0x551f5500},
+	{0x0000a17c, 0x6602551e},
+	{0x0000a180, 0x66006601},
+	{0x0000a184, 0x661e661f},
+	{0x0000a188, 0x7703661d},
+	{0x0000a18c, 0x77017702},
+	{0x0000a190, 0x00007700},
+	{0x0000a194, 0x00000000},
+	{0x0000a198, 0x00000000},
+	{0x0000a19c, 0x00000000},
+	{0x0000a1a0, 0x00000000},
+	{0x0000a1a4, 0x00000000},
+	{0x0000a1a8, 0x00000000},
+	{0x0000a1ac, 0x00000000},
+	{0x0000a1b0, 0x00000000},
+	{0x0000a1b4, 0x00000000},
+	{0x0000a1b8, 0x00000000},
+	{0x0000a1bc, 0x00000000},
+	{0x0000a1c0, 0x00000000},
+	{0x0000a1c4, 0x00000000},
+	{0x0000a1c8, 0x00000000},
+	{0x0000a1cc, 0x00000000},
+	{0x0000a1d0, 0x00000000},
+	{0x0000a1d4, 0x00000000},
+	{0x0000a1d8, 0x00000000},
+	{0x0000a1dc, 0x00000000},
+	{0x0000a1e0, 0x00000000},
+	{0x0000a1e4, 0x00000000},
+	{0x0000a1e8, 0x00000000},
+	{0x0000a1ec, 0x00000000},
+	{0x0000a1f0, 0x00000396},
+	{0x0000a1f4, 0x00000396},
+	{0x0000a1f8, 0x00000396},
+	{0x0000a1fc, 0x00000296},
+};
+
+static const u32 ar9485Modes_high_power_tx_gain_1_0[][5] = {
+	/*   Addr      5G_HT20     5G_HT40     2G_HT40     2G_HT20 */
+	{0x0000a410, 0x000050d9, 0x000050d9, 0x000050d8, 0x000050d8},
+	{0x0000a500, 0x00022200, 0x00022200, 0x00000000, 0x00000000},
+	{0x0000a504, 0x05062002, 0x05062002, 0x04000002, 0x04000002},
+	{0x0000a508, 0x0c002e00, 0x0c002e00, 0x08000004, 0x08000004},
+	{0x0000a50c, 0x11062202, 0x11062202, 0x0d000200, 0x0d000200},
+	{0x0000a510, 0x17022e00, 0x17022e00, 0x11000202, 0x11000202},
+	{0x0000a514, 0x1d000ec2, 0x1d000ec2, 0x15000400, 0x15000400},
+	{0x0000a518, 0x25020ec0, 0x25020ec0, 0x19000402, 0x19000402},
+	{0x0000a51c, 0x2b020ec3, 0x2b020ec3, 0x1d000404, 0x1d000404},
+	{0x0000a520, 0x2f001f04, 0x2f001f04, 0x21000603, 0x21000603},
+	{0x0000a524, 0x35001fc4, 0x35001fc4, 0x25000605, 0x25000605},
+	{0x0000a528, 0x3c022f04, 0x3c022f04, 0x2a000a03, 0x2a000a03},
+	{0x0000a52c, 0x41023e85, 0x41023e85, 0x2c000a04, 0x2c000a04},
+	{0x0000a530, 0x48023ec6, 0x48023ec6, 0x2e000a20, 0x2e000a20},
+	{0x0000a534, 0x4d023f01, 0x4d023f01, 0x34000e20, 0x34000e20},
+	{0x0000a538, 0x53023f4b, 0x53023f4b, 0x38000e22, 0x38000e22},
+	{0x0000a53c, 0x5a027f09, 0x5a027f09, 0x3c000e24, 0x3c000e24},
+	{0x0000a540, 0x5f027fc9, 0x5f027fc9, 0x40000e26, 0x40000e26},
+	{0x0000a544, 0x6502feca, 0x6502feca, 0x43001640, 0x43001640},
+	{0x0000a548, 0x6b02ff4a, 0x6b02ff4a, 0x46001660, 0x46001660},
+	{0x0000a54c, 0x7203feca, 0x7203feca, 0x49001861, 0x49001861},
+	{0x0000a550, 0x7703ff0b, 0x7703ff0b, 0x4c001a81, 0x4c001a81},
+	{0x0000a554, 0x7d06ffcb, 0x7d06ffcb, 0x4f001a83, 0x4f001a83},
+	{0x0000a558, 0x8407ff0b, 0x8407ff0b, 0x54001c85, 0x54001c85},
+	{0x0000a55c, 0x8907ffcb, 0x8907ffcb, 0x58001ce5, 0x58001ce5},
+	{0x0000a560, 0x900fff0b, 0x900fff0b, 0x5b001ce9, 0x5b001ce9},
+	{0x0000a564, 0x960fffcb, 0x960fffcb, 0x60001eeb, 0x60001eeb},
+	{0x0000a568, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a56c, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a570, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a574, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a578, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a57c, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x00016044, 0x05b6b2db, 0x05b6b2db, 0x05b6b2db, 0x05b6b2db},
+};
+
+static const u32 ar9485_1_0[][2] = {
+	/*  Addr      allmodes */
+	{0x0000a580, 0x00000000},
+	{0x0000a584, 0x00000000},
+	{0x0000a588, 0x00000000},
+	{0x0000a58c, 0x00000000},
+	{0x0000a590, 0x00000000},
+	{0x0000a594, 0x00000000},
+	{0x0000a598, 0x00000000},
+	{0x0000a59c, 0x00000000},
+	{0x0000a5a0, 0x00000000},
+	{0x0000a5a4, 0x00000000},
+	{0x0000a5a8, 0x00000000},
+	{0x0000a5ac, 0x00000000},
+	{0x0000a5b0, 0x00000000},
+	{0x0000a5b4, 0x00000000},
+	{0x0000a5b8, 0x00000000},
+	{0x0000a5bc, 0x00000000},
+};
+
+static const u32 ar9485_1_0_radio_core[][2] = {
+	/*   Addr     allmodes */
+	{0x00016000, 0x36db6db6},
+	{0x00016004, 0x6db6db40},
+	{0x00016008, 0x73800000},
+	{0x0001600c, 0x00000000},
+	{0x00016040, 0x7f80fff8},
+	{0x00016048, 0x6c92426e},
+	{0x0001604c, 0x000f0278},
+	{0x00016050, 0x6db6db6c},
+	{0x00016054, 0x6db60000},
+	{0x00016080, 0x00080000},
+	{0x00016084, 0x0e48048c},
+	{0x00016088, 0x14214514},
+	{0x0001608c, 0x119f081e},
+	{0x00016090, 0x24926490},
+	{0x00016098, 0xd28b3330},
+	{0x000160a0, 0xc2108ffe},
+	{0x000160a4, 0x812fc370},
+	{0x000160a8, 0x423c8000},
+	{0x000160b4, 0x92480040},
+	{0x000160c0, 0x006db6db},
+	{0x000160c4, 0x0186db60},
+	{0x000160c8, 0x6db6db6c},
+	{0x000160cc, 0x6de6fbe0},
+	{0x000160d0, 0xf7dfcf3c},
+	{0x00016100, 0x04cb0001},
+	{0x00016104, 0xfff80015},
+	{0x00016108, 0x00080010},
+	{0x00016144, 0x01884080},
+	{0x00016148, 0x00008040},
+	{0x00016180, 0x08453333},
+	{0x00016184, 0x18e82f01},
+	{0x00016188, 0x00000000},
+	{0x0001618c, 0x00000000},
+	{0x00016240, 0x08400000},
+	{0x00016244, 0x1bf90f00},
+	{0x00016248, 0x00000000},
+	{0x0001624c, 0x00000000},
+	{0x00016280, 0x01000015},
+	{0x00016284, 0x00d30000},
+	{0x00016288, 0x00318000},
+	{0x0001628c, 0x50000000},
+	{0x00016290, 0x4b96210f},
+	{0x00016380, 0x00000000},
+	{0x00016384, 0x00000000},
+	{0x00016388, 0x00800700},
+	{0x0001638c, 0x00800700},
+	{0x00016390, 0x00800700},
+	{0x00016394, 0x00000000},
+	{0x00016398, 0x00000000},
+	{0x0001639c, 0x00000000},
+	{0x000163a0, 0x00000001},
+	{0x000163a4, 0x00000001},
+	{0x000163a8, 0x00000000},
+	{0x000163ac, 0x00000000},
+	{0x000163b0, 0x00000000},
+	{0x000163b4, 0x00000000},
+	{0x000163b8, 0x00000000},
+	{0x000163bc, 0x00000000},
+	{0x000163c0, 0x000000a0},
+	{0x000163c4, 0x000c0000},
+	{0x000163c8, 0x14021402},
+	{0x000163cc, 0x00001402},
+	{0x000163d0, 0x00000000},
+	{0x000163d4, 0x00000000},
+	{0x00016c40, 0x1319c178},
+	{0x00016c44, 0x10000000},
+};
+
+static const u32 ar9485Modes_lowest_ob_db_tx_gain_1_0[][5] = {
+	/*  Addr       5G_HT20     5G_HT40     2G_HT40     2G_HT20 */
+	{0x0000a410, 0x000050d9, 0x000050d9, 0x000050d8, 0x000050d8},
+	{0x0000a500, 0x00022200, 0x00022200, 0x00000000, 0x00000000},
+	{0x0000a504, 0x05062002, 0x05062002, 0x04000002, 0x04000002},
+	{0x0000a508, 0x0c002e00, 0x0c002e00, 0x08000004, 0x08000004},
+	{0x0000a50c, 0x11062202, 0x11062202, 0x0d000200, 0x0d000200},
+	{0x0000a510, 0x17022e00, 0x17022e00, 0x11000202, 0x11000202},
+	{0x0000a514, 0x1d000ec2, 0x1d000ec2, 0x15000400, 0x15000400},
+	{0x0000a518, 0x25020ec0, 0x25020ec0, 0x19000402, 0x19000402},
+	{0x0000a51c, 0x2b020ec3, 0x2b020ec3, 0x1d000404, 0x1d000404},
+	{0x0000a520, 0x2f001f04, 0x2f001f04, 0x21000603, 0x21000603},
+	{0x0000a524, 0x35001fc4, 0x35001fc4, 0x25000605, 0x25000605},
+	{0x0000a528, 0x3c022f04, 0x3c022f04, 0x2a000a03, 0x2a000a03},
+	{0x0000a52c, 0x41023e85, 0x41023e85, 0x2c000a04, 0x2c000a04},
+	{0x0000a530, 0x48023ec6, 0x48023ec6, 0x2e000a20, 0x2e000a20},
+	{0x0000a534, 0x4d023f01, 0x4d023f01, 0x34000e20, 0x34000e20},
+	{0x0000a538, 0x53023f4b, 0x53023f4b, 0x38000e22, 0x38000e22},
+	{0x0000a53c, 0x5a027f09, 0x5a027f09, 0x3c000e24, 0x3c000e24},
+	{0x0000a540, 0x5f027fc9, 0x5f027fc9, 0x40000e26, 0x40000e26},
+	{0x0000a544, 0x6502feca, 0x6502feca, 0x43001640, 0x43001640},
+	{0x0000a548, 0x6b02ff4a, 0x6b02ff4a, 0x46001660, 0x46001660},
+	{0x0000a54c, 0x7203feca, 0x7203feca, 0x49001861, 0x49001861},
+	{0x0000a550, 0x7703ff0b, 0x7703ff0b, 0x4c001a81, 0x4c001a81},
+	{0x0000a554, 0x7d06ffcb, 0x7d06ffcb, 0x4f001a83, 0x4f001a83},
+	{0x0000a558, 0x8407ff0b, 0x8407ff0b, 0x54001c85, 0x54001c85},
+	{0x0000a55c, 0x8907ffcb, 0x8907ffcb, 0x58001ce5, 0x58001ce5},
+	{0x0000a560, 0x900fff0b, 0x900fff0b, 0x5b001ce9, 0x5b001ce9},
+	{0x0000a564, 0x960fffcb, 0x960fffcb, 0x60001eeb, 0x60001eeb},
+	{0x0000a568, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a56c, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a570, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a574, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a578, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a57c, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x00016044, 0x05b6b2db, 0x05b6b2db, 0x05b6b2db, 0x05b6b2db},
+};
+
+static const u32 ar9485_1_0_baseband_core[][2] = {
+	/* Addr      allmodes  */
+	{0x00009800, 0xafe68e30},
+	{0x00009804, 0xfd14e000},
+	{0x00009808, 0x9c0a8f6b},
+	{0x0000980c, 0x04800000},
+	{0x00009814, 0x9280c00a},
+	{0x00009818, 0x00000000},
+	{0x0000981c, 0x00020028},
+	{0x00009834, 0x5f3ca3de},
+	{0x00009838, 0x0108ecff},
+	{0x0000983c, 0x14750600},
+	{0x00009880, 0x201fff00},
+	{0x00009884, 0x00001042},
+	{0x000098a4, 0x00200400},
+	{0x000098b0, 0x52440bbe},
+	{0x000098bc, 0x00000002},
+	{0x000098d0, 0x004b6a8e},
+	{0x000098d4, 0x00000820},
+	{0x000098dc, 0x00000000},
+	{0x000098f0, 0x00000000},
+	{0x000098f4, 0x00000000},
+	{0x00009c04, 0x00000000},
+	{0x00009c08, 0x03200000},
+	{0x00009c0c, 0x00000000},
+	{0x00009c10, 0x00000000},
+	{0x00009c14, 0x00046384},
+	{0x00009c18, 0x05b6b440},
+	{0x00009c1c, 0x00b6b440},
+	{0x00009d00, 0xc080a333},
+	{0x00009d04, 0x40206c10},
+	{0x00009d08, 0x009c4060},
+	{0x00009d0c, 0x1883800a},
+	{0x00009d10, 0x01834061},
+	{0x00009d14, 0x00c00400},
+	{0x00009d18, 0x00000000},
+	{0x00009d1c, 0x00000000},
+	{0x00009e08, 0x0038233c},
+	{0x00009e24, 0x990bb515},
+	{0x00009e28, 0x0a6f0000},
+	{0x00009e30, 0x06336f77},
+	{0x00009e34, 0x6af6532f},
+	{0x00009e38, 0x0cc80c00},
+	{0x00009e40, 0x0d261820},
+	{0x00009e4c, 0x00001004},
+	{0x00009e50, 0x00ff03f1},
+	{0x00009fc0, 0x80be4788},
+	{0x00009fc4, 0x0001efb5},
+	{0x00009fcc, 0x40000014},
+	{0x0000a20c, 0x00000000},
+	{0x0000a210, 0x00000000},
+	{0x0000a220, 0x00000000},
+	{0x0000a224, 0x00000000},
+	{0x0000a228, 0x10002310},
+	{0x0000a23c, 0x00000000},
+	{0x0000a244, 0x0c000000},
+	{0x0000a2a0, 0x00000001},
+	{0x0000a2c0, 0x00000001},
+	{0x0000a2c8, 0x00000000},
+	{0x0000a2cc, 0x18c43433},
+	{0x0000a2d4, 0x00000000},
+	{0x0000a2dc, 0x00000000},
+	{0x0000a2e0, 0x00000000},
+	{0x0000a2e4, 0x00000000},
+	{0x0000a2e8, 0x00000000},
+	{0x0000a2ec, 0x00000000},
+	{0x0000a2f0, 0x00000000},
+	{0x0000a2f4, 0x00000000},
+	{0x0000a2f8, 0x00000000},
+	{0x0000a344, 0x00000000},
+	{0x0000a34c, 0x00000000},
+	{0x0000a350, 0x0000a000},
+	{0x0000a364, 0x00000000},
+	{0x0000a370, 0x00000000},
+	{0x0000a390, 0x00000001},
+	{0x0000a394, 0x00000444},
+	{0x0000a398, 0x001f0e0f},
+	{0x0000a39c, 0x0075393f},
+	{0x0000a3a0, 0xb79f6427},
+	{0x0000a3a4, 0x00000000},
+	{0x0000a3a8, 0xaaaaaaaa},
+	{0x0000a3ac, 0x3c466478},
+	{0x0000a3c0, 0x20202020},
+	{0x0000a3c4, 0x22222220},
+	{0x0000a3c8, 0x20200020},
+	{0x0000a3cc, 0x20202020},
+	{0x0000a3d0, 0x20202020},
+	{0x0000a3d4, 0x20202020},
+	{0x0000a3d8, 0x20202020},
+	{0x0000a3dc, 0x20202020},
+	{0x0000a3e0, 0x20202020},
+	{0x0000a3e4, 0x20202020},
+	{0x0000a3e8, 0x20202020},
+	{0x0000a3ec, 0x20202020},
+	{0x0000a3f0, 0x00000000},
+	{0x0000a3f4, 0x00000006},
+	{0x0000a3f8, 0x0cdbd380},
+	{0x0000a3fc, 0x000f0f01},
+	{0x0000a400, 0x8fa91f01},
+	{0x0000a404, 0x00000000},
+	{0x0000a408, 0x0e79e5c6},
+	{0x0000a40c, 0x00820820},
+	{0x0000a414, 0x1ce739ce},
+	{0x0000a418, 0x2d0011ce},
+	{0x0000a41c, 0x1ce739ce},
+	{0x0000a420, 0x000001ce},
+	{0x0000a424, 0x1ce739ce},
+	{0x0000a428, 0x000001ce},
+	{0x0000a42c, 0x1ce739ce},
+	{0x0000a430, 0x1ce739ce},
+	{0x0000a434, 0x00000000},
+	{0x0000a438, 0x00001801},
+	{0x0000a43c, 0x00000000},
+	{0x0000a440, 0x00000000},
+	{0x0000a444, 0x00000000},
+	{0x0000a448, 0x04000000},
+	{0x0000a44c, 0x00000001},
+	{0x0000a450, 0x00010000},
+	{0x0000a458, 0x00000000},
+	{0x0000a5c4, 0x3fad9d74},
+	{0x0000a5c8, 0x0048060a},
+	{0x0000a5cc, 0x00000637},
+	{0x0000a760, 0x03020100},
+	{0x0000a764, 0x09080504},
+	{0x0000a768, 0x0d0c0b0a},
+	{0x0000a76c, 0x13121110},
+	{0x0000a770, 0x31301514},
+	{0x0000a774, 0x35343332},
+	{0x0000a778, 0x00000036},
+	{0x0000a780, 0x00000838},
+	{0x0000a7c0, 0x00000000},
+	{0x0000a7c4, 0xfffffffc},
+	{0x0000a7c8, 0x00000000},
+	{0x0000a7cc, 0x00000000},
+	{0x0000a7d0, 0x00000000},
+	{0x0000a7d4, 0x00000004},
+	{0x0000a7dc, 0x00000001},
+};
+
+static const u32 ar9485Modes_high_ob_db_tx_gain_1_0[][5] = {
+	/* Addr        5G_HT20     5G_HT40     2G_HT40    2G_HT20  */
+	{0x0000a410, 0x000050d9, 0x000050d9, 0x000050d8, 0x000050d8},
+	{0x0000a500, 0x00022200, 0x00022200, 0x00000000, 0x00000000},
+	{0x0000a504, 0x05062002, 0x05062002, 0x04000002, 0x04000002},
+	{0x0000a508, 0x0c002e00, 0x0c002e00, 0x08000004, 0x08000004},
+	{0x0000a50c, 0x11062202, 0x11062202, 0x0d000200, 0x0d000200},
+	{0x0000a510, 0x17022e00, 0x17022e00, 0x11000202, 0x11000202},
+	{0x0000a514, 0x1d000ec2, 0x1d000ec2, 0x15000400, 0x15000400},
+	{0x0000a518, 0x25020ec0, 0x25020ec0, 0x19000402, 0x19000402},
+	{0x0000a51c, 0x2b020ec3, 0x2b020ec3, 0x1d000404, 0x1d000404},
+	{0x0000a520, 0x2f001f04, 0x2f001f04, 0x21000603, 0x21000603},
+	{0x0000a524, 0x35001fc4, 0x35001fc4, 0x25000605, 0x25000605},
+	{0x0000a528, 0x3c022f04, 0x3c022f04, 0x2a000a03, 0x2a000a03},
+	{0x0000a52c, 0x41023e85, 0x41023e85, 0x2c000a04, 0x2c000a04},
+	{0x0000a530, 0x48023ec6, 0x48023ec6, 0x2e000a20, 0x2e000a20},
+	{0x0000a534, 0x4d023f01, 0x4d023f01, 0x34000e20, 0x34000e20},
+	{0x0000a538, 0x53023f4b, 0x53023f4b, 0x38000e22, 0x38000e22},
+	{0x0000a53c, 0x5a027f09, 0x5a027f09, 0x3c000e24, 0x3c000e24},
+	{0x0000a540, 0x5f027fc9, 0x5f027fc9, 0x40000e26, 0x40000e26},
+	{0x0000a544, 0x6502feca, 0x6502feca, 0x43001640, 0x43001640},
+	{0x0000a548, 0x6b02ff4a, 0x6b02ff4a, 0x46001660, 0x46001660},
+	{0x0000a54c, 0x7203feca, 0x7203feca, 0x49001861, 0x49001861},
+	{0x0000a550, 0x7703ff0b, 0x7703ff0b, 0x4c001a81, 0x4c001a81},
+	{0x0000a554, 0x7d06ffcb, 0x7d06ffcb, 0x4f001a83, 0x4f001a83},
+	{0x0000a558, 0x8407ff0b, 0x8407ff0b, 0x54001c85, 0x54001c85},
+	{0x0000a55c, 0x8907ffcb, 0x8907ffcb, 0x58001ce5, 0x58001ce5},
+	{0x0000a560, 0x900fff0b, 0x900fff0b, 0x5b001ce9, 0x5b001ce9},
+	{0x0000a564, 0x960fffcb, 0x960fffcb, 0x60001eeb, 0x60001eeb},
+	{0x0000a568, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a56c, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a570, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a574, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a578, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a57c, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x00016044, 0x05b6b2db, 0x05b6b2db, 0x05b6b2db, 0x05b6b2db},
+};
+
+static const u32 ar9485Common_rx_gain_1_0[][2] = {
+	/* Addr      allmodes  */
+	{0x0000a000, 0x00010000},
+	{0x0000a004, 0x00030002},
+	{0x0000a008, 0x00050004},
+	{0x0000a00c, 0x00810080},
+	{0x0000a010, 0x01800082},
+	{0x0000a014, 0x01820181},
+	{0x0000a018, 0x01840183},
+	{0x0000a01c, 0x01880185},
+	{0x0000a020, 0x018a0189},
+	{0x0000a024, 0x02850284},
+	{0x0000a028, 0x02890288},
+	{0x0000a02c, 0x03850384},
+	{0x0000a030, 0x03890388},
+	{0x0000a034, 0x038b038a},
+	{0x0000a038, 0x038d038c},
+	{0x0000a03c, 0x03910390},
+	{0x0000a040, 0x03930392},
+	{0x0000a044, 0x03950394},
+	{0x0000a048, 0x00000396},
+	{0x0000a04c, 0x00000000},
+	{0x0000a050, 0x00000000},
+	{0x0000a054, 0x00000000},
+	{0x0000a058, 0x00000000},
+	{0x0000a05c, 0x00000000},
+	{0x0000a060, 0x00000000},
+	{0x0000a064, 0x00000000},
+	{0x0000a068, 0x00000000},
+	{0x0000a06c, 0x00000000},
+	{0x0000a070, 0x00000000},
+	{0x0000a074, 0x00000000},
+	{0x0000a078, 0x00000000},
+	{0x0000a07c, 0x00000000},
+	{0x0000a080, 0x28282828},
+	{0x0000a084, 0x28282828},
+	{0x0000a088, 0x28282828},
+	{0x0000a08c, 0x28282828},
+	{0x0000a090, 0x28282828},
+	{0x0000a094, 0x21212128},
+	{0x0000a098, 0x171c1c1c},
+	{0x0000a09c, 0x02020212},
+	{0x0000a0a0, 0x00000202},
+	{0x0000a0a4, 0x00000000},
+	{0x0000a0a8, 0x00000000},
+	{0x0000a0ac, 0x00000000},
+	{0x0000a0b0, 0x00000000},
+	{0x0000a0b4, 0x00000000},
+	{0x0000a0b8, 0x00000000},
+	{0x0000a0bc, 0x00000000},
+	{0x0000a0c0, 0x001f0000},
+	{0x0000a0c4, 0x111f1100},
+	{0x0000a0c8, 0x111d111e},
+	{0x0000a0cc, 0x111b111c},
+	{0x0000a0d0, 0x22032204},
+	{0x0000a0d4, 0x22012202},
+	{0x0000a0d8, 0x221f2200},
+	{0x0000a0dc, 0x221d221e},
+	{0x0000a0e0, 0x33013302},
+	{0x0000a0e4, 0x331f3300},
+	{0x0000a0e8, 0x4402331e},
+	{0x0000a0ec, 0x44004401},
+	{0x0000a0f0, 0x441e441f},
+	{0x0000a0f4, 0x55015502},
+	{0x0000a0f8, 0x551f5500},
+	{0x0000a0fc, 0x6602551e},
+	{0x0000a100, 0x66006601},
+	{0x0000a104, 0x661e661f},
+	{0x0000a108, 0x7703661d},
+	{0x0000a10c, 0x77017702},
+	{0x0000a110, 0x00007700},
+	{0x0000a114, 0x00000000},
+	{0x0000a118, 0x00000000},
+	{0x0000a11c, 0x00000000},
+	{0x0000a120, 0x00000000},
+	{0x0000a124, 0x00000000},
+	{0x0000a128, 0x00000000},
+	{0x0000a12c, 0x00000000},
+	{0x0000a130, 0x00000000},
+	{0x0000a134, 0x00000000},
+	{0x0000a138, 0x00000000},
+	{0x0000a13c, 0x00000000},
+	{0x0000a140, 0x001f0000},
+	{0x0000a144, 0x111f1100},
+	{0x0000a148, 0x111d111e},
+	{0x0000a14c, 0x111b111c},
+	{0x0000a150, 0x22032204},
+	{0x0000a154, 0x22012202},
+	{0x0000a158, 0x221f2200},
+	{0x0000a15c, 0x221d221e},
+	{0x0000a160, 0x33013302},
+	{0x0000a164, 0x331f3300},
+	{0x0000a168, 0x4402331e},
+	{0x0000a16c, 0x44004401},
+	{0x0000a170, 0x441e441f},
+	{0x0000a174, 0x55015502},
+	{0x0000a178, 0x551f5500},
+	{0x0000a17c, 0x6602551e},
+	{0x0000a180, 0x66006601},
+	{0x0000a184, 0x661e661f},
+	{0x0000a188, 0x7703661d},
+	{0x0000a18c, 0x77017702},
+	{0x0000a190, 0x00007700},
+	{0x0000a194, 0x00000000},
+	{0x0000a198, 0x00000000},
+	{0x0000a19c, 0x00000000},
+	{0x0000a1a0, 0x00000000},
+	{0x0000a1a4, 0x00000000},
+	{0x0000a1a8, 0x00000000},
+	{0x0000a1ac, 0x00000000},
+	{0x0000a1b0, 0x00000000},
+	{0x0000a1b4, 0x00000000},
+	{0x0000a1b8, 0x00000000},
+	{0x0000a1bc, 0x00000000},
+	{0x0000a1c0, 0x00000000},
+	{0x0000a1c4, 0x00000000},
+	{0x0000a1c8, 0x00000000},
+	{0x0000a1cc, 0x00000000},
+	{0x0000a1d0, 0x00000000},
+	{0x0000a1d4, 0x00000000},
+	{0x0000a1d8, 0x00000000},
+	{0x0000a1dc, 0x00000000},
+	{0x0000a1e0, 0x00000000},
+	{0x0000a1e4, 0x00000000},
+	{0x0000a1e8, 0x00000000},
+	{0x0000a1ec, 0x00000000},
+	{0x0000a1f0, 0x00000396},
+	{0x0000a1f4, 0x00000396},
+	{0x0000a1f8, 0x00000396},
+	{0x0000a1fc, 0x00000296},
+};
+
+static const u32 ar9485_1_0_pcie_phy_pll_on_clkreq_enable_L1[][2] = {
+	/*   Addr    allmodes  */
+	{0x00018c00, 0x10252e5e},
+	{0x00018c04, 0x000801d8},
+	{0x00018c08, 0x0000580c},
+};
+
+static const u32 ar9485_1_0_pcie_phy_clkreq_enable_L1[][2] = {
+	/*  Addr    allmodes   */
+	{0x00018c00, 0x10253e5e},
+	{0x00018c04, 0x000801d8},
+	{0x00018c08, 0x0000580c},
+};
+
+static const u32 ar9485_1_0_soc_preamble[][2] = {
+	/*   Addr     allmodes */
+	{0x000040a4, 0x00a0c9c9},
+	{0x00007048, 0x00000004},
+};
+
+static const u32 ar9485_fast_clock_1_0_baseband_postamble[][3] = {
+	/*   Addr      5G_HT20     5G_HT40 */
+	{0x00009e00, 0x03721821, 0x03721821},
+	{0x0000a230, 0x0000400b, 0x00004016},
+	{0x0000a254, 0x00000898, 0x00001130},
+};
+
+static const u32 ar9485_1_0_baseband_postamble[][5] = {
+	/* Addr        5G_HT20     5G_HT40     2G_HT40     2G_HT20 */
+	{0x00009810, 0xd00a8005, 0xd00a8005, 0xd00a8005, 0xd00a8005},
+	{0x00009820, 0x206a002e, 0x206a002e, 0x206a002e, 0x206a002e},
+	{0x00009824, 0x5ac640d0, 0x5ac640d0, 0x5ac640d0, 0x5ac640d0},
+	{0x00009828, 0x06903081, 0x06903081, 0x06903881, 0x06903881},
+	{0x0000982c, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4},
+	{0x00009830, 0x0000059c, 0x0000059c, 0x0000059c, 0x0000059c},
+	{0x00009c00, 0x00000044, 0x00000044, 0x00000044, 0x00000044},
+	{0x00009e00, 0x0372161e, 0x0372161e, 0x037216a0, 0x037216a0},
+	{0x00009e04, 0x00182020, 0x00182020, 0x00182020, 0x00182020},
+	{0x00009e0c, 0x6c4000e2, 0x6d4000e2, 0x6d4000e2, 0x6c4000e2},
+	{0x00009e10, 0x7ec88d2e, 0x7ec88d2e, 0x7ec80d2e, 0x7ec80d2e},
+	{0x00009e14, 0x31395d5e, 0x3139605e, 0x3139605e, 0x31395d5e},
+	{0x00009e18, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
+	{0x00009e1c, 0x0001cf9c, 0x0001cf9c, 0x00021f9c, 0x00021f9c},
+	{0x00009e20, 0x000003b5, 0x000003b5, 0x000003ce, 0x000003ce},
+	{0x00009e2c, 0x0000001c, 0x0000001c, 0x00000021, 0x00000021},
+	{0x00009e3c, 0xcf946220, 0xcf946220, 0xcf946222, 0xcf946222},
+	{0x00009e44, 0x02321e27, 0x02321e27, 0x02282324, 0x02282324},
+	{0x00009e48, 0x5030201a, 0x5030201a, 0x50302010, 0x50302010},
+	{0x00009fc8, 0x0003f000, 0x0003f000, 0x0001a000, 0x0001a000},
+	{0x0000a204, 0x01303fc0, 0x01303fc4, 0x01303fc4, 0x01303fc0},
+	{0x0000a208, 0x00000104, 0x00000104, 0x00000004, 0x00000004},
+	{0x0000a230, 0x0000400a, 0x00004014, 0x00004016, 0x0000400b},
+	{0x0000a234, 0x10000fff, 0x10000fff, 0x10000fff, 0x10000fff},
+	{0x0000a238, 0xffb81018, 0xffb81018, 0xffb81018, 0xffb81018},
+	{0x0000a250, 0x00000000, 0x00000000, 0x00000210, 0x00000108},
+	{0x0000a254, 0x000007d0, 0x00000fa0, 0x00001130, 0x00000898},
+	{0x0000a258, 0x02020002, 0x02020002, 0x02020002, 0x02020002},
+	{0x0000a25c, 0x01000e0e, 0x01000e0e, 0x01000e0e, 0x01000e0e},
+	{0x0000a260, 0x3a021501, 0x3a021501, 0x3a021501, 0x3a021501},
+	{0x0000a264, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e},
+	{0x0000a280, 0x00000007, 0x00000007, 0x0000000b, 0x0000000b},
+	{0x0000a284, 0x00000000, 0x00000000, 0x000002a0, 0x000002a0},
+	{0x0000a288, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
+	{0x0000a28c, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
+	{0x0000a2c4, 0x00158d18, 0x00158d18, 0x00158d18, 0x00158d18},
+	{0x0000a2d0, 0x00071981, 0x00071981, 0x00071981, 0x00071982},
+	{0x0000a2d8, 0xf999a83a, 0xf999a83a, 0xf999a83a, 0xf999a83a},
+	{0x0000a358, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
+	{0x0000be04, 0x00802020, 0x00802020, 0x00802020, 0x00802020},
+	{0x0000be18, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
+};
+
+static const u32 ar9485Modes_low_ob_db_tx_gain_1_0[][5] = {
+	/*  Addr      5G_HT20    5G_HT40     2G_HT40     2G_HT20   */
+	{0x0000a410, 0x000050d9, 0x000050d9, 0x000050d8, 0x000050d8},
+	{0x0000a500, 0x00022200, 0x00022200, 0x00000000, 0x00000000},
+	{0x0000a504, 0x05062002, 0x05062002, 0x04000002, 0x04000002},
+	{0x0000a508, 0x0c002e00, 0x0c002e00, 0x08000004, 0x08000004},
+	{0x0000a50c, 0x11062202, 0x11062202, 0x0d000200, 0x0d000200},
+	{0x0000a510, 0x17022e00, 0x17022e00, 0x11000202, 0x11000202},
+	{0x0000a514, 0x1d000ec2, 0x1d000ec2, 0x15000400, 0x15000400},
+	{0x0000a518, 0x25020ec0, 0x25020ec0, 0x19000402, 0x19000402},
+	{0x0000a51c, 0x2b020ec3, 0x2b020ec3, 0x1d000404, 0x1d000404},
+	{0x0000a520, 0x2f001f04, 0x2f001f04, 0x21000603, 0x21000603},
+	{0x0000a524, 0x35001fc4, 0x35001fc4, 0x25000605, 0x25000605},
+	{0x0000a528, 0x3c022f04, 0x3c022f04, 0x2a000a03, 0x2a000a03},
+	{0x0000a52c, 0x41023e85, 0x41023e85, 0x2c000a04, 0x2c000a04},
+	{0x0000a530, 0x48023ec6, 0x48023ec6, 0x2e000a20, 0x2e000a20},
+	{0x0000a534, 0x4d023f01, 0x4d023f01, 0x34000e20, 0x34000e20},
+	{0x0000a538, 0x53023f4b, 0x53023f4b, 0x38000e22, 0x38000e22},
+	{0x0000a53c, 0x5a027f09, 0x5a027f09, 0x3c000e24, 0x3c000e24},
+	{0x0000a540, 0x5f027fc9, 0x5f027fc9, 0x40000e26, 0x40000e26},
+	{0x0000a544, 0x6502feca, 0x6502feca, 0x43001640, 0x43001640},
+	{0x0000a548, 0x6b02ff4a, 0x6b02ff4a, 0x46001660, 0x46001660},
+	{0x0000a54c, 0x7203feca, 0x7203feca, 0x49001861, 0x49001861},
+	{0x0000a550, 0x7703ff0b, 0x7703ff0b, 0x4c001a81, 0x4c001a81},
+	{0x0000a554, 0x7d06ffcb, 0x7d06ffcb, 0x4f001a83, 0x4f001a83},
+	{0x0000a558, 0x8407ff0b, 0x8407ff0b, 0x54001c85, 0x54001c85},
+	{0x0000a55c, 0x8907ffcb, 0x8907ffcb, 0x58001ce5, 0x58001ce5},
+	{0x0000a560, 0x900fff0b, 0x900fff0b, 0x5b001ce9, 0x5b001ce9},
+	{0x0000a564, 0x960fffcb, 0x960fffcb, 0x60001eeb, 0x60001eeb},
+	{0x0000a568, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a56c, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a570, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a574, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a578, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x0000a57c, 0x9c1fff0b, 0x9c1fff0b, 0x60001eeb, 0x60001eeb},
+	{0x00016044, 0x05b6b2db, 0x05b6b2db, 0x05b6b2db, 0x05b6b2db},
+};
+
+static const u32 ar9485_1_0_pcie_phy_clkreq_disable_L1[][2] = {
+	/*   Addr     allmodes */
+	{0x00018c00, 0x10213e5e},
+	{0x00018c04, 0x000801d8},
+	{0x00018c08, 0x0000580c},
+};
+
+static const u32 ar9485_1_0_radio_postamble[][2] = {
+	/*   Addr     allmodes */
+	{0x0001609c, 0x0b283f31},
+	{0x000160ac, 0x24611800},
+	{0x000160b0, 0x03284f3e},
+	{0x0001610c, 0x00170000},
+	{0x00016140, 0x10804008},
+};
+
+static const u32 ar9485_1_0_mac_core[][2] = {
+	/*  Addr      allmodes */
+	{0x00000008, 0x00000000},
+	{0x00000030, 0x00020085},
+	{0x00000034, 0x00000005},
+	{0x00000040, 0x00000000},
+	{0x00000044, 0x00000000},
+	{0x00000048, 0x00000008},
+	{0x0000004c, 0x00000010},
+	{0x00000050, 0x00000000},
+	{0x00001040, 0x002ffc0f},
+	{0x00001044, 0x002ffc0f},
+	{0x00001048, 0x002ffc0f},
+	{0x0000104c, 0x002ffc0f},
+	{0x00001050, 0x002ffc0f},
+	{0x00001054, 0x002ffc0f},
+	{0x00001058, 0x002ffc0f},
+	{0x0000105c, 0x002ffc0f},
+	{0x00001060, 0x002ffc0f},
+	{0x00001064, 0x002ffc0f},
+	{0x000010f0, 0x00000100},
+	{0x00001270, 0x00000000},
+	{0x000012b0, 0x00000000},
+	{0x000012f0, 0x00000000},
+	{0x0000143c, 0x00000000},
+	{0x0000147c, 0x00000000},
+	{0x00008000, 0x00000000},
+	{0x00008004, 0x00000000},
+	{0x00008008, 0x00000000},
+	{0x0000800c, 0x00000000},
+	{0x00008018, 0x00000000},
+	{0x00008020, 0x00000000},
+	{0x00008038, 0x00000000},
+	{0x0000803c, 0x00000000},
+	{0x00008040, 0x00000000},
+	{0x00008044, 0x00000000},
+	{0x00008048, 0x00000000},
+	{0x0000804c, 0xffffffff},
+	{0x00008054, 0x00000000},
+	{0x00008058, 0x00000000},
+	{0x0000805c, 0x000fc78f},
+	{0x00008060, 0x0000000f},
+	{0x00008064, 0x00000000},
+	{0x00008070, 0x00000310},
+	{0x00008074, 0x00000020},
+	{0x00008078, 0x00000000},
+	{0x0000809c, 0x0000000f},
+	{0x000080a0, 0x00000000},
+	{0x000080a4, 0x02ff0000},
+	{0x000080a8, 0x0e070605},
+	{0x000080ac, 0x0000000d},
+	{0x000080b0, 0x00000000},
+	{0x000080b4, 0x00000000},
+	{0x000080b8, 0x00000000},
+	{0x000080bc, 0x00000000},
+	{0x000080c0, 0x2a800000},
+	{0x000080c4, 0x06900168},
+	{0x000080c8, 0x13881c20},
+	{0x000080cc, 0x01f40000},
+	{0x000080d0, 0x00252500},
+	{0x000080d4, 0x00a00000},
+	{0x000080d8, 0x00400000},
+	{0x000080dc, 0x00000000},
+	{0x000080e0, 0xffffffff},
+	{0x000080e4, 0x0000ffff},
+	{0x000080e8, 0x3f3f3f3f},
+	{0x000080ec, 0x00000000},
+	{0x000080f0, 0x00000000},
+	{0x000080f4, 0x00000000},
+	{0x000080fc, 0x00020000},
+	{0x00008100, 0x00000000},
+	{0x00008108, 0x00000052},
+	{0x0000810c, 0x00000000},
+	{0x00008110, 0x00000000},
+	{0x00008114, 0x000007ff},
+	{0x00008118, 0x000000aa},
+	{0x0000811c, 0x00003210},
+	{0x00008124, 0x00000000},
+	{0x00008128, 0x00000000},
+	{0x0000812c, 0x00000000},
+	{0x00008130, 0x00000000},
+	{0x00008134, 0x00000000},
+	{0x00008138, 0x00000000},
+	{0x0000813c, 0x0000ffff},
+	{0x00008144, 0xffffffff},
+	{0x00008168, 0x00000000},
+	{0x0000816c, 0x00000000},
+	{0x00008170, 0x18486200},
+	{0x00008174, 0x33332210},
+	{0x00008178, 0x00000000},
+	{0x0000817c, 0x00020000},
+	{0x000081c0, 0x00000000},
+	{0x000081c4, 0x33332210},
+	{0x000081c8, 0x00000000},
+	{0x000081cc, 0x00000000},
+	{0x000081d4, 0x00000000},
+	{0x000081ec, 0x00000000},
+	{0x000081f0, 0x00000000},
+	{0x000081f4, 0x00000000},
+	{0x000081f8, 0x00000000},
+	{0x000081fc, 0x00000000},
+	{0x00008240, 0x00100000},
+	{0x00008244, 0x0010f400},
+	{0x00008248, 0x00000800},
+	{0x0000824c, 0x0001e800},
+	{0x00008250, 0x00000000},
+	{0x00008254, 0x00000000},
+	{0x00008258, 0x00000000},
+	{0x0000825c, 0x40000000},
+	{0x00008260, 0x00080922},
+	{0x00008264, 0x9ca00010},
+	{0x00008268, 0xffffffff},
+	{0x0000826c, 0x0000ffff},
+	{0x00008270, 0x00000000},
+	{0x00008274, 0x40000000},
+	{0x00008278, 0x003e4180},
+	{0x0000827c, 0x00000004},
+	{0x00008284, 0x0000002c},
+	{0x00008288, 0x0000002c},
+	{0x0000828c, 0x000000ff},
+	{0x00008294, 0x00000000},
+	{0x00008298, 0x00000000},
+	{0x0000829c, 0x00000000},
+	{0x00008300, 0x00000140},
+	{0x00008314, 0x00000000},
+	{0x0000831c, 0x0000010d},
+	{0x00008328, 0x00000000},
+	{0x0000832c, 0x00000007},
+	{0x00008330, 0x00000302},
+	{0x00008334, 0x00000700},
+	{0x00008338, 0x00ff0000},
+	{0x0000833c, 0x02400000},
+	{0x00008340, 0x000107ff},
+	{0x00008344, 0xa248105b},
+	{0x00008348, 0x008f0000},
+	{0x0000835c, 0x00000000},
+	{0x00008360, 0xffffffff},
+	{0x00008364, 0xffffffff},
+	{0x00008368, 0x00000000},
+	{0x00008370, 0x00000000},
+	{0x00008374, 0x000000ff},
+	{0x00008378, 0x00000000},
+	{0x0000837c, 0x00000000},
+	{0x00008380, 0xffffffff},
+	{0x00008384, 0xffffffff},
+	{0x00008390, 0xffffffff},
+	{0x00008394, 0xffffffff},
+	{0x00008398, 0x00000000},
+	{0x0000839c, 0x00000000},
+	{0x000083a0, 0x00000000},
+	{0x000083a4, 0x0000fa14},
+	{0x000083a8, 0x000f0c00},
+	{0x000083ac, 0x33332210},
+	{0x000083b0, 0x33332210},
+	{0x000083b4, 0x33332210},
+	{0x000083b8, 0x33332210},
+	{0x000083bc, 0x00000000},
+	{0x000083c0, 0x00000000},
+	{0x000083c4, 0x00000000},
+	{0x000083c8, 0x00000000},
+	{0x000083cc, 0x00000200},
+	{0x000083d0, 0x000301ff},
+};
+#endif
-- 
1.7.0.4

[PATCH 03/26] ath9k_hw: Enable hw initialization for AR9485

[Vasanthakumar Thiagarajan]

Also make it a supported mac

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_hw.c |    1 +
 drivers/net/wireless/ath/ath9k/hw.c        |    1 +
 drivers/net/wireless/ath/ath9k/hw.h        |    1 +
 3 files changed, 3 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_hw.c b/drivers/net/wireless/ath/ath9k/ar9003_hw.c
index c2a0571..0e3e259 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_hw.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_hw.c
@@ -24,6 +24,7 @@ static bool ar9003_hw_macversion_supported(u32 macversion)
 {
 	switch (macversion) {
 	case AR_SREV_VERSION_9300:
+	case AR_SREV_VERSION_9485:
 		return true;
 	default:
 		break;
diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index 9b1ee7f..f533aad 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -629,6 +629,7 @@ int ath9k_hw_init(struct ath_hw *ah)
 	case AR9287_DEVID_PCIE:
 	case AR2427_DEVID_PCIE:
 	case AR9300_DEVID_PCIE:
+	case AR9300_DEVID_AR9485_PCIE:
 		break;
 	default:
 		if (common->bus_ops->ath_bus_type == ATH_USB)
diff --git a/drivers/net/wireless/ath/ath9k/hw.h b/drivers/net/wireless/ath/ath9k/hw.h
index 5fcfa48..bde1df3 100644
--- a/drivers/net/wireless/ath/ath9k/hw.h
+++ b/drivers/net/wireless/ath/ath9k/hw.h
@@ -44,6 +44,7 @@
 #define AR9287_DEVID_PCI	0x002d
 #define AR9287_DEVID_PCIE	0x002e
 #define AR9300_DEVID_PCIE	0x0030
+#define AR9300_DEVID_AR9485_PCIE 0x0032
 
 #define AR5416_AR9100_DEVID	0x000b
 
-- 
1.7.0.4

[PATCH 04/26] ath9k_hw: Initialize mode registers for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_hw.c |  195 ++++++++++++++++++----------
 1 files changed, 129 insertions(+), 66 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_hw.c b/drivers/net/wireless/ath/ath9k/ar9003_hw.c
index 0e3e259..f01c289 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_hw.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_hw.c
@@ -17,6 +17,7 @@
 #include "hw.h"
 #include "ar9003_mac.h"
 #include "ar9003_2p2_initvals.h"
+#include "ar9485_initvals.h"
 
 /* General hardware code for the AR9003 hadware family */
 
@@ -39,72 +40,134 @@ static bool ar9003_hw_macversion_supported(u32 macversion)
  */
 static void ar9003_hw_init_mode_regs(struct ath_hw *ah)
 {
-	/* mac */
-	INIT_INI_ARRAY(&ah->iniMac[ATH_INI_PRE], NULL, 0, 0);
-	INIT_INI_ARRAY(&ah->iniMac[ATH_INI_CORE],
-		       ar9300_2p2_mac_core,
-		       ARRAY_SIZE(ar9300_2p2_mac_core), 2);
-	INIT_INI_ARRAY(&ah->iniMac[ATH_INI_POST],
-		       ar9300_2p2_mac_postamble,
-		       ARRAY_SIZE(ar9300_2p2_mac_postamble), 5);
-
-	/* bb */
-	INIT_INI_ARRAY(&ah->iniBB[ATH_INI_PRE], NULL, 0, 0);
-	INIT_INI_ARRAY(&ah->iniBB[ATH_INI_CORE],
-		       ar9300_2p2_baseband_core,
-		       ARRAY_SIZE(ar9300_2p2_baseband_core), 2);
-	INIT_INI_ARRAY(&ah->iniBB[ATH_INI_POST],
-		       ar9300_2p2_baseband_postamble,
-		       ARRAY_SIZE(ar9300_2p2_baseband_postamble), 5);
-
-	/* radio */
-	INIT_INI_ARRAY(&ah->iniRadio[ATH_INI_PRE], NULL, 0, 0);
-	INIT_INI_ARRAY(&ah->iniRadio[ATH_INI_CORE],
-		       ar9300_2p2_radio_core,
-		       ARRAY_SIZE(ar9300_2p2_radio_core), 2);
-	INIT_INI_ARRAY(&ah->iniRadio[ATH_INI_POST],
-		       ar9300_2p2_radio_postamble,
-		       ARRAY_SIZE(ar9300_2p2_radio_postamble), 5);
-
-	/* soc */
-	INIT_INI_ARRAY(&ah->iniSOC[ATH_INI_PRE],
-		       ar9300_2p2_soc_preamble,
-		       ARRAY_SIZE(ar9300_2p2_soc_preamble), 2);
-	INIT_INI_ARRAY(&ah->iniSOC[ATH_INI_CORE], NULL, 0, 0);
-	INIT_INI_ARRAY(&ah->iniSOC[ATH_INI_POST],
-		       ar9300_2p2_soc_postamble,
-		       ARRAY_SIZE(ar9300_2p2_soc_postamble), 5);
-
-	/* rx/tx gain */
-	INIT_INI_ARRAY(&ah->iniModesRxGain,
-		       ar9300Common_rx_gain_table_2p2,
-		       ARRAY_SIZE(ar9300Common_rx_gain_table_2p2), 2);
-	INIT_INI_ARRAY(&ah->iniModesTxGain,
-		       ar9300Modes_lowest_ob_db_tx_gain_table_2p2,
-		       ARRAY_SIZE(ar9300Modes_lowest_ob_db_tx_gain_table_2p2),
-		       5);
-
-	/* Load PCIE SERDES settings from INI */
-
-	/* Awake Setting */
-
-	INIT_INI_ARRAY(&ah->iniPcieSerdes,
-		       ar9300PciePhy_pll_on_clkreq_disable_L1_2p2,
-		       ARRAY_SIZE(ar9300PciePhy_pll_on_clkreq_disable_L1_2p2),
-		       2);
-
-	/* Sleep Setting */
-
-	INIT_INI_ARRAY(&ah->iniPcieSerdesLowPower,
-		       ar9300PciePhy_clkreq_enable_L1_2p2,
-		       ARRAY_SIZE(ar9300PciePhy_clkreq_enable_L1_2p2),
-		       2);
-
-	/* Fast clock modal settings */
-	INIT_INI_ARRAY(&ah->iniModesAdditional,
-		       ar9300Modes_fast_clock_2p2,
-		       ARRAY_SIZE(ar9300Modes_fast_clock_2p2),
-		       3);
+	if (AR_SREV_9485(ah)) {
+		/* mac */
+		INIT_INI_ARRAY(&ah->iniMac[ATH_INI_PRE], NULL, 0, 0);
+		INIT_INI_ARRAY(&ah->iniMac[ATH_INI_CORE],
+				ar9485_1_0_mac_core,
+				ARRAY_SIZE(ar9485_1_0_mac_core), 2);
+		INIT_INI_ARRAY(&ah->iniMac[ATH_INI_POST],
+				ar9485_1_0_mac_postamble,
+				ARRAY_SIZE(ar9485_1_0_mac_postamble), 5);
+
+		/* bb */
+		INIT_INI_ARRAY(&ah->iniBB[ATH_INI_PRE], ar9485_1_0,
+				ARRAY_SIZE(ar9485_1_0), 2);
+		INIT_INI_ARRAY(&ah->iniBB[ATH_INI_CORE],
+				ar9485_1_0_baseband_core,
+				ARRAY_SIZE(ar9485_1_0_baseband_core), 2);
+		INIT_INI_ARRAY(&ah->iniBB[ATH_INI_POST],
+				ar9485_1_0_baseband_postamble,
+				ARRAY_SIZE(ar9485_1_0_baseband_postamble), 5);
+
+		/* radio */
+		INIT_INI_ARRAY(&ah->iniRadio[ATH_INI_PRE], NULL, 0, 0);
+		INIT_INI_ARRAY(&ah->iniRadio[ATH_INI_CORE],
+				ar9485_1_0_radio_core,
+				ARRAY_SIZE(ar9485_1_0_radio_core), 2);
+		INIT_INI_ARRAY(&ah->iniRadio[ATH_INI_POST],
+				ar9485_1_0_radio_postamble,
+				ARRAY_SIZE(ar9485_1_0_radio_postamble), 2);
+
+		/* soc */
+		INIT_INI_ARRAY(&ah->iniSOC[ATH_INI_PRE],
+				ar9485_1_0_soc_preamble,
+				ARRAY_SIZE(ar9485_1_0_soc_preamble), 2);
+		INIT_INI_ARRAY(&ah->iniSOC[ATH_INI_CORE], NULL, 0, 0);
+		INIT_INI_ARRAY(&ah->iniSOC[ATH_INI_POST], NULL, 0, 0);
+
+		/* rx/tx gain */
+		INIT_INI_ARRAY(&ah->iniModesRxGain,
+				ar9485Common_rx_gain_1_0,
+				ARRAY_SIZE(ar9485Common_rx_gain_1_0), 2);
+		INIT_INI_ARRAY(&ah->iniModesTxGain,
+				ar9485Modes_lowest_ob_db_tx_gain_1_0,
+				ARRAY_SIZE(ar9485Modes_lowest_ob_db_tx_gain_1_0),
+				5);
+
+		/* Load PCIE SERDES settings from INI */
+
+		/* Awake Setting */
+
+		INIT_INI_ARRAY(&ah->iniPcieSerdes,
+				ar9485_1_0_pcie_phy_pll_on_clkreq_disable_L1,
+				ARRAY_SIZE(ar9485_1_0_pcie_phy_pll_on_clkreq_disable_L1),
+				2);
+
+		/* Sleep Setting */
+
+		INIT_INI_ARRAY(&ah->iniPcieSerdesLowPower,
+				ar9485_1_0_pcie_phy_pll_on_clkreq_enable_L1,
+				ARRAY_SIZE(ar9485_1_0_pcie_phy_pll_on_clkreq_enable_L1),
+				2);
+	} else {
+		/* mac */
+		INIT_INI_ARRAY(&ah->iniMac[ATH_INI_PRE], NULL, 0, 0);
+		INIT_INI_ARRAY(&ah->iniMac[ATH_INI_CORE],
+				ar9300_2p2_mac_core,
+				ARRAY_SIZE(ar9300_2p2_mac_core), 2);
+		INIT_INI_ARRAY(&ah->iniMac[ATH_INI_POST],
+				ar9300_2p2_mac_postamble,
+				ARRAY_SIZE(ar9300_2p2_mac_postamble), 5);
+
+		/* bb */
+		INIT_INI_ARRAY(&ah->iniBB[ATH_INI_PRE], NULL, 0, 0);
+		INIT_INI_ARRAY(&ah->iniBB[ATH_INI_CORE],
+				ar9300_2p2_baseband_core,
+				ARRAY_SIZE(ar9300_2p2_baseband_core), 2);
+		INIT_INI_ARRAY(&ah->iniBB[ATH_INI_POST],
+				ar9300_2p2_baseband_postamble,
+				ARRAY_SIZE(ar9300_2p2_baseband_postamble), 5);
+
+		/* radio */
+		INIT_INI_ARRAY(&ah->iniRadio[ATH_INI_PRE], NULL, 0, 0);
+		INIT_INI_ARRAY(&ah->iniRadio[ATH_INI_CORE],
+				ar9300_2p2_radio_core,
+				ARRAY_SIZE(ar9300_2p2_radio_core), 2);
+		INIT_INI_ARRAY(&ah->iniRadio[ATH_INI_POST],
+				ar9300_2p2_radio_postamble,
+				ARRAY_SIZE(ar9300_2p2_radio_postamble), 5);
+
+		/* soc */
+		INIT_INI_ARRAY(&ah->iniSOC[ATH_INI_PRE],
+				ar9300_2p2_soc_preamble,
+				ARRAY_SIZE(ar9300_2p2_soc_preamble), 2);
+		INIT_INI_ARRAY(&ah->iniSOC[ATH_INI_CORE], NULL, 0, 0);
+		INIT_INI_ARRAY(&ah->iniSOC[ATH_INI_POST],
+				ar9300_2p2_soc_postamble,
+				ARRAY_SIZE(ar9300_2p2_soc_postamble), 5);
+
+		/* rx/tx gain */
+		INIT_INI_ARRAY(&ah->iniModesRxGain,
+				ar9300Common_rx_gain_table_2p2,
+				ARRAY_SIZE(ar9300Common_rx_gain_table_2p2), 2);
+		INIT_INI_ARRAY(&ah->iniModesTxGain,
+				ar9300Modes_lowest_ob_db_tx_gain_table_2p2,
+				ARRAY_SIZE(ar9300Modes_lowest_ob_db_tx_gain_table_2p2),
+				5);
+
+		/* Load PCIE SERDES settings from INI */
+
+		/* Awake Setting */
+
+		INIT_INI_ARRAY(&ah->iniPcieSerdes,
+				ar9300PciePhy_pll_on_clkreq_disable_L1_2p2,
+				ARRAY_SIZE(ar9300PciePhy_pll_on_clkreq_disable_L1_2p2),
+				2);
+
+		/* Sleep Setting */
+
+		INIT_INI_ARRAY(&ah->iniPcieSerdesLowPower,
+				ar9300PciePhy_clkreq_enable_L1_2p2,
+				ARRAY_SIZE(ar9300PciePhy_clkreq_enable_L1_2p2),
+				2);
+
+		/* Fast clock modal settings */
+		INIT_INI_ARRAY(&ah->iniModesAdditional,
+				ar9300Modes_fast_clock_2p2,
+				ARRAY_SIZE(ar9300Modes_fast_clock_2p2),
+				3);
+	}
 }
 
 static void ar9003_tx_gain_table_apply(struct ath_hw *ah)
-- 
1.7.0.4

[PATCH 05/26] ath9k_hw: Initialize tx/rx gain table from initvals.h for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_hw.c |   82 +++++++++++++++++++++-------
 1 files changed, 62 insertions(+), 20 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_hw.c b/drivers/net/wireless/ath/ath9k/ar9003_hw.c
index f01c289..21a5bfe 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_hw.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_hw.c
@@ -175,22 +175,52 @@ static void ar9003_tx_gain_table_apply(struct ath_hw *ah)
 	switch (ar9003_hw_get_tx_gain_idx(ah)) {
 	case 0:
 	default:
-		INIT_INI_ARRAY(&ah->iniModesTxGain,
-			       ar9300Modes_lowest_ob_db_tx_gain_table_2p2,
-			       ARRAY_SIZE(ar9300Modes_lowest_ob_db_tx_gain_table_2p2),
-			       5);
+		if (AR_SREV_9485(ah))
+			INIT_INI_ARRAY(&ah->iniModesTxGain,
+				       ar9485Modes_lowest_ob_db_tx_gain_1_0,
+				       ARRAY_SIZE(ar9485Modes_lowest_ob_db_tx_gain_1_0),
+				       5);
+		else
+			INIT_INI_ARRAY(&ah->iniModesTxGain,
+				       ar9300Modes_lowest_ob_db_tx_gain_table_2p2,
+				       ARRAY_SIZE(ar9300Modes_lowest_ob_db_tx_gain_table_2p2),
+				       5);
 		break;
 	case 1:
-		INIT_INI_ARRAY(&ah->iniModesTxGain,
-			       ar9300Modes_high_ob_db_tx_gain_table_2p2,
-			       ARRAY_SIZE(ar9300Modes_high_ob_db_tx_gain_table_2p2),
-			       5);
+		if (AR_SREV_9485(ah))
+			INIT_INI_ARRAY(&ah->iniModesTxGain,
+				       ar9485Modes_high_ob_db_tx_gain_1_0,
+				       ARRAY_SIZE(ar9485Modes_lowest_ob_db_tx_gain_1_0),
+				       5);
+		else
+			INIT_INI_ARRAY(&ah->iniModesTxGain,
+				       ar9300Modes_high_ob_db_tx_gain_table_2p2,
+				       ARRAY_SIZE(ar9300Modes_high_ob_db_tx_gain_table_2p2),
+				       5);
 		break;
 	case 2:
-		INIT_INI_ARRAY(&ah->iniModesTxGain,
-			       ar9300Modes_low_ob_db_tx_gain_table_2p2,
-			       ARRAY_SIZE(ar9300Modes_low_ob_db_tx_gain_table_2p2),
-			       5);
+		if (AR_SREV_9485(ah))
+			INIT_INI_ARRAY(&ah->iniModesTxGain,
+				       ar9485Modes_low_ob_db_tx_gain_1_0,
+				       ARRAY_SIZE(ar9485Modes_lowest_ob_db_tx_gain_1_0),
+				       5);
+		else
+			INIT_INI_ARRAY(&ah->iniModesTxGain,
+				       ar9300Modes_low_ob_db_tx_gain_table_2p2,
+				       ARRAY_SIZE(ar9300Modes_low_ob_db_tx_gain_table_2p2),
+				       5);
+		break;
+	case 3:
+		if (AR_SREV_9485(ah))
+			INIT_INI_ARRAY(&ah->iniModesTxGain,
+				       ar9485Modes_high_power_tx_gain_1_0,
+				       ARRAY_SIZE(ar9485Modes_high_power_tx_gain_1_0),
+				       5);
+		else
+			INIT_INI_ARRAY(&ah->iniModesTxGain,
+				       ar9300Modes_high_power_tx_gain_table_2p2,
+				       ARRAY_SIZE(ar9300Modes_high_power_tx_gain_table_2p2),
+				       5);
 		break;
 	}
 }
@@ -200,16 +230,28 @@ static void ar9003_rx_gain_table_apply(struct ath_hw *ah)
 	switch (ar9003_hw_get_rx_gain_idx(ah)) {
 	case 0:
 	default:
-		INIT_INI_ARRAY(&ah->iniModesRxGain,
-			       ar9300Common_rx_gain_table_2p2,
-			       ARRAY_SIZE(ar9300Common_rx_gain_table_2p2),
-			       2);
+		if (AR_SREV_9485(ah))
+			INIT_INI_ARRAY(&ah->iniModesRxGain,
+				       ar9485Common_rx_gain_1_0,
+				       ARRAY_SIZE(ar9485Common_rx_gain_1_0),
+				       2);
+		else
+			INIT_INI_ARRAY(&ah->iniModesRxGain,
+				       ar9300Common_rx_gain_table_2p2,
+				       ARRAY_SIZE(ar9300Common_rx_gain_table_2p2),
+				       2);
 		break;
 	case 1:
-		INIT_INI_ARRAY(&ah->iniModesRxGain,
-			       ar9300Common_wo_xlna_rx_gain_table_2p2,
-			       ARRAY_SIZE(ar9300Common_wo_xlna_rx_gain_table_2p2),
-			       2);
+		if (AR_SREV_9485(ah))
+			INIT_INI_ARRAY(&ah->iniModesRxGain,
+				       ar9485Common_wo_xlna_rx_gain_1_0,
+				       ARRAY_SIZE(ar9485Common_wo_xlna_rx_gain_1_0),
+				       2);
+		else
+			INIT_INI_ARRAY(&ah->iniModesRxGain,
+				       ar9300Common_wo_xlna_rx_gain_table_2p2,
+				       ARRAY_SIZE(ar9300Common_wo_xlna_rx_gain_table_2p2),
+				       2);
 		break;
 	}
 }
-- 
1.7.0.4

[PATCH 06/26] ath9k_hw: Eeeprom changes for AR9485

[Vasanthakumar Thiagarajan]

Calibration data are stored at 4k address (0xfff). The cal data
for AR9485 is not compressed so its lengh can exceed 1024 limit,
take care of that.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |    8 ++++++--
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.h |    1 +
 2 files changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index 4aecc10..6cbfbfa 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -3317,7 +3317,10 @@ static int ar9300_eeprom_restore_internal(struct ath_hw *ah,
 	memcpy(mptr, &ar9300_default, mdata_size);
 
 	read = ar9300_read_eeprom;
-	cptr = AR9300_BASE_ADDR;
+	if (AR_SREV_9485(ah))
+		cptr = AR9300_BASE_ADDR_4K;
+	else
+		cptr = AR9300_BASE_ADDR;
 	ath_print(common, ATH_DBG_EEPROM,
 		"Trying EEPROM accesss at Address 0x%04x\n", cptr);
 	if (ar9300_check_eeprom_header(ah, read, cptr))
@@ -3360,7 +3363,8 @@ found:
 			  "Found block at %x: code=%d ref=%d"
 			  "length=%d major=%d minor=%d\n", cptr, code,
 			  reference, length, major, minor);
-		if (length >= 1024) {
+		if ((!AR_SREV_9485(ah) && length >= 1024) ||
+		    (AR_SREV_9485(ah) && length >= (4 * 1024))) {
 			ath_print(common, ATH_DBG_EEPROM,
 				  "Skipping bad header\n");
 			cptr -= COMP_HDR_LEN;
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.h b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.h
index 57f64db..d189c87 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.h
@@ -78,6 +78,7 @@
 #define AR9300_EEPROM_SIZE (16*1024)
 #define FIXED_CCA_THRESHOLD 15
 
+#define AR9300_BASE_ADDR_4K 0xfff
 #define AR9300_BASE_ADDR 0x3ff
 #define AR9300_BASE_ADDR_512 0x1ff
 
-- 
1.7.0.4

[PATCH 07/26] ath9k_hw: Disable LDPC for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/hw.c |    6 ++++--
 1 files changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index f533aad..513ae64 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -1941,8 +1941,10 @@ int ath9k_hw_fill_cap_info(struct ath_hw *ah)
 	}
 
 	if (AR_SREV_9300_20_OR_LATER(ah)) {
-		pCap->hw_caps |= ATH9K_HW_CAP_EDMA | ATH9K_HW_CAP_LDPC |
-				 ATH9K_HW_CAP_FASTCLOCK;
+		pCap->hw_caps |= ATH9K_HW_CAP_EDMA | ATH9K_HW_CAP_FASTCLOCK;
+		if (!AR_SREV_9485(ah))
+			pCap->hw_caps |= ATH9K_HW_CAP_LDPC;
+
 		pCap->rx_hp_qdepth = ATH9K_HW_RX_HP_QDEPTH;
 		pCap->rx_lp_qdepth = ATH9K_HW_RX_LP_QDEPTH;
 		pCap->rx_status_len = sizeof(struct ar9003_rxs);
-- 
1.7.0.4

[PATCH 08/26] ath9k: Disable TX STBC for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/init.c |    4 +++-
 1 files changed, 3 insertions(+), 1 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/init.c b/drivers/net/wireless/ath/ath9k/init.c
index 2962ce3..3439fa7 100644
--- a/drivers/net/wireless/ath/ath9k/init.c
+++ b/drivers/net/wireless/ath/ath9k/init.c
@@ -210,7 +210,9 @@ static void setup_ht_cap(struct ath_softc *sc,
 	ht_info->ampdu_factor = IEEE80211_HT_MAX_AMPDU_64K;
 	ht_info->ampdu_density = IEEE80211_HT_MPDU_DENSITY_8;
 
-	if (AR_SREV_9300_20_OR_LATER(ah))
+	if (AR_SREV_9485(ah))
+		max_streams = 1;
+	else if (AR_SREV_9300_20_OR_LATER(ah))
 		max_streams = 3;
 	else
 		max_streams = 2;
-- 
1.7.0.4

[PATCH 09/26] ath9k: Enable extended synch for AR9485 to fix L0s recovery issue

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath.h        |    1 +
 drivers/net/wireless/ath/ath9k/hw.c   |    5 +++++
 drivers/net/wireless/ath/ath9k/hw.h   |    2 ++
 drivers/net/wireless/ath/ath9k/main.c |    3 +++
 drivers/net/wireless/ath/ath9k/pci.c  |   12 ++++++++++++
 5 files changed, 23 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/ath/ath.h b/drivers/net/wireless/ath/ath.h
index 26bdbee..f913db4 100644
--- a/drivers/net/wireless/ath/ath.h
+++ b/drivers/net/wireless/ath/ath.h
@@ -131,6 +131,7 @@ struct ath_bus_ops {
 	void (*read_cachesize)(struct ath_common *common, int *csz);
 	bool (*eeprom_read)(struct ath_common *common, u32 off, u16 *data);
 	void (*bt_coex_prep)(struct ath_common *common);
+	void (*extn_synch_en)(struct ath_common *common);
 };
 
 struct ath_common {
diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index 513ae64..b1d3c1e 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -1984,6 +1984,11 @@ int ath9k_hw_fill_cap_info(struct ath_hw *ah)
 
 
 
+	if (AR_SREV_9485_10(ah)) {
+		pCap->pcie_lcr_extsync_en = true;
+		pCap->pcie_lcr_offset = 0x80;
+	}
+
 	return 0;
 }
 
diff --git a/drivers/net/wireless/ath/ath9k/hw.h b/drivers/net/wireless/ath/ath9k/hw.h
index bde1df3..1eb6a14 100644
--- a/drivers/net/wireless/ath/ath9k/hw.h
+++ b/drivers/net/wireless/ath/ath9k/hw.h
@@ -210,6 +210,8 @@ struct ath9k_hw_capabilities {
 	u8 rx_status_len;
 	u8 tx_desc_len;
 	u8 txs_len;
+	u16 pcie_lcr_offset;
+	bool pcie_lcr_extsync_en;
 };
 
 struct ath9k_ops_config {
diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index f026a03..581dbd7 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -1188,6 +1188,9 @@ static int ath9k_start(struct ieee80211_hw *hw)
 
 	pm_qos_update_request(&sc->pm_qos_req, 55);
 
+	if (ah->caps.pcie_lcr_extsync_en && common->bus_ops->extn_synch_en)
+		common->bus_ops->extn_synch_en(common);
+
 mutex_unlock:
 	mutex_unlock(&sc->mutex);
 
diff --git a/drivers/net/wireless/ath/ath9k/pci.c b/drivers/net/wireless/ath/ath9k/pci.c
index 09f69a9..c5a523d 100644
--- a/drivers/net/wireless/ath/ath9k/pci.c
+++ b/drivers/net/wireless/ath/ath9k/pci.c
@@ -104,11 +104,23 @@ static void ath_pci_bt_coex_prep(struct ath_common *common)
 	pci_write_config_byte(pdev, ATH_PCIE_CAP_LINK_CTRL, aspm);
 }
 
+static void ath_pci_extn_synch_enable(struct ath_common *common)
+{
+	struct ath_softc *sc = (struct ath_softc *) common->priv;
+	struct pci_dev *pdev = to_pci_dev(sc->dev);
+	u8 lnkctl;
+
+	pci_read_config_byte(pdev, sc->sc_ah->caps.pcie_lcr_offset, &lnkctl);
+	lnkctl |= PCI_EXP_LNKCTL_ES;
+	pci_write_config_byte(pdev, sc->sc_ah->caps.pcie_lcr_offset, lnkctl);
+}
+
 static const struct ath_bus_ops ath_pci_bus_ops = {
 	.ath_bus_type = ATH_PCI,
 	.read_cachesize = ath_pci_read_cachesize,
 	.eeprom_read = ath_pci_eeprom_read,
 	.bt_coex_prep = ath_pci_bt_coex_prep,
+	.extn_synch_en = ath_pci_extn_synch_enable,
 };
 
 static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
-- 
1.7.0.4

[PATCH 10/26] ath9k: Configure pll control for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_phy.c |   16 ++++++++++------
 drivers/net/wireless/ath/ath9k/hw.c         |    7 ++++++-
 drivers/net/wireless/ath/ath9k/reg.h        |    2 ++
 3 files changed, 18 insertions(+), 7 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
index b34a9e9..4e35bda 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
@@ -390,14 +390,18 @@ static u32 ar9003_hw_compute_pll_control(struct ath_hw *ah,
 {
 	u32 pll;
 
-	pll = SM(0x5, AR_RTC_9300_PLL_REFDIV);
+	if (AR_SREV_9485(ah))
+		pll = 0x142c;
+	else {
+		pll = SM(0x5, AR_RTC_9300_PLL_REFDIV);
 
-	if (chan && IS_CHAN_HALF_RATE(chan))
-		pll |= SM(0x1, AR_RTC_9300_PLL_CLKSEL);
-	else if (chan && IS_CHAN_QUARTER_RATE(chan))
-		pll |= SM(0x2, AR_RTC_9300_PLL_CLKSEL);
+		if (chan && IS_CHAN_HALF_RATE(chan))
+			pll |= SM(0x1, AR_RTC_9300_PLL_CLKSEL);
+		else if (chan && IS_CHAN_QUARTER_RATE(chan))
+			pll |= SM(0x2, AR_RTC_9300_PLL_CLKSEL);
 
-	pll |= SM(0x2c, AR_RTC_9300_PLL_DIV);
+		pll |= SM(0x2c, AR_RTC_9300_PLL_DIV);
+	}
 
 	return pll;
 }
diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index b1d3c1e..79a4e70 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -676,7 +676,12 @@ static void ath9k_hw_init_qos(struct ath_hw *ah)
 static void ath9k_hw_init_pll(struct ath_hw *ah,
 			      struct ath9k_channel *chan)
 {
-	u32 pll = ath9k_hw_compute_pll_control(ah, chan);
+	u32 pll;
+
+	if (AR_SREV_9485(ah))
+		REG_WRITE(ah, AR_RTC_PLL_CONTROL2, 0x886666);
+
+	pll = ath9k_hw_compute_pll_control(ah, chan);
 
 	REG_WRITE(ah, AR_RTC_PLL_CONTROL, pll);
 
diff --git a/drivers/net/wireless/ath/ath9k/reg.h b/drivers/net/wireless/ath/ath9k/reg.h
index 0153ba1..d3257f7 100644
--- a/drivers/net/wireless/ath/ath9k/reg.h
+++ b/drivers/net/wireless/ath/ath9k/reg.h
@@ -1114,6 +1114,8 @@ enum {
 #define AR_RTC_PLL_CONTROL \
 	((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0014) : 0x7014)
 
+#define AR_RTC_PLL_CONTROL2	0x703c
+
 #define AR_RTC_PLL_DIV          0x0000001f
 #define AR_RTC_PLL_DIV_S        0
 #define AR_RTC_PLL_DIV2         0x00000020
-- 
1.7.0.4

Re: [PATCH 10/26] ath9k: Configure pll control for AR9485

[Felix Fietkau]

On 2010-12-01 8:32 AM, Vasanthakumar Thiagarajan wrote:
> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
> ---
>  drivers/net/wireless/ath/ath9k/ar9003_phy.c |   16 ++++++++++------
>  drivers/net/wireless/ath/ath9k/hw.c         |    7 ++++++-
>  drivers/net/wireless/ath/ath9k/reg.h        |    2 ++
>  3 files changed, 18 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> index b34a9e9..4e35bda 100644
> --- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> +++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> @@ -390,14 +390,18 @@ static u32 ar9003_hw_compute_pll_control(struct ath_hw *ah,
>  {
>  	u32 pll;
>  
> -	pll = SM(0x5, AR_RTC_9300_PLL_REFDIV);
> +	if (AR_SREV_9485(ah))
> +		pll = 0x142c;
> +	else {
> +		pll = SM(0x5, AR_RTC_9300_PLL_REFDIV);
>  
> -	if (chan && IS_CHAN_HALF_RATE(chan))
> -		pll |= SM(0x1, AR_RTC_9300_PLL_CLKSEL);
> -	else if (chan && IS_CHAN_QUARTER_RATE(chan))
> -		pll |= SM(0x2, AR_RTC_9300_PLL_CLKSEL);
> +		if (chan && IS_CHAN_HALF_RATE(chan))
> +			pll |= SM(0x1, AR_RTC_9300_PLL_CLKSEL);
> +		else if (chan && IS_CHAN_QUARTER_RATE(chan))
> +			pll |= SM(0x2, AR_RTC_9300_PLL_CLKSEL);
>  
> -	pll |= SM(0x2c, AR_RTC_9300_PLL_DIV);
> +		pll |= SM(0x2c, AR_RTC_9300_PLL_DIV);
> +	}
>  
>  	return pll;
>  }
NACK for this part. Take a look at what gets set for the older chips:

0x5 << AR_RTC_9300_PLL_REFDIV_S == 0x1400
0x2c << AR_RTC_9300_PLL_DIV_S == 0x002c

Hint: it's exactly the same ;)

- Felix

Re: [PATCH 10/26] ath9k: Configure pll control for AR9485

[Vasanthakumar Thiagarajan]

On Wed, Dec 01, 2010 at 10:09:24PM +0530, Felix Fietkau wrote:
> On 2010-12-01 8:32 AM, Vasanthakumar Thiagarajan wrote:
> > Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
> > ---
> >  drivers/net/wireless/ath/ath9k/ar9003_phy.c |   16 ++++++++++------
> >  drivers/net/wireless/ath/ath9k/hw.c         |    7 ++++++-
> >  drivers/net/wireless/ath/ath9k/reg.h        |    2 ++
> >  3 files changed, 18 insertions(+), 7 deletions(-)
> > 
> > diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> > index b34a9e9..4e35bda 100644
> > --- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> > +++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> > @@ -390,14 +390,18 @@ static u32 ar9003_hw_compute_pll_control(struct ath_hw *ah,
> >  {
> >  	u32 pll;
> >  
> > -	pll = SM(0x5, AR_RTC_9300_PLL_REFDIV);
> > +	if (AR_SREV_9485(ah))
> > +		pll = 0x142c;
> > +	else {
> > +		pll = SM(0x5, AR_RTC_9300_PLL_REFDIV);
> >  
> > -	if (chan && IS_CHAN_HALF_RATE(chan))
> > -		pll |= SM(0x1, AR_RTC_9300_PLL_CLKSEL);
> > -	else if (chan && IS_CHAN_QUARTER_RATE(chan))
> > -		pll |= SM(0x2, AR_RTC_9300_PLL_CLKSEL);
> > +		if (chan && IS_CHAN_HALF_RATE(chan))
> > +			pll |= SM(0x1, AR_RTC_9300_PLL_CLKSEL);
> > +		else if (chan && IS_CHAN_QUARTER_RATE(chan))
> > +			pll |= SM(0x2, AR_RTC_9300_PLL_CLKSEL);
> >  
> > -	pll |= SM(0x2c, AR_RTC_9300_PLL_DIV);
> > +		pll |= SM(0x2c, AR_RTC_9300_PLL_DIV);
> > +	}
> >  
> >  	return pll;
> >  }
> NACK for this part. Take a look at what gets set for the older chips:
> 
> 0x5 << AR_RTC_9300_PLL_REFDIV_S == 0x1400
> 0x2c << AR_RTC_9300_PLL_DIV_S == 0x002c

True, but older ar9003 chips have half/quarter rate support (which is not
implemented right now), in that case pll configuration would differ
for AR9485.

Vasanth

Re: [PATCH 10/26] ath9k: Configure pll control for AR9485

[Vasanthakumar Thiagarajan]

On Thu, Dec 02, 2010 at 10:35:49AM +0530, Vasanth Thiagarajan wrote:
> On Wed, Dec 01, 2010 at 10:09:24PM +0530, Felix Fietkau wrote:
> > On 2010-12-01 8:32 AM, Vasanthakumar Thiagarajan wrote:
> > > Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
> > > ---
> > >  drivers/net/wireless/ath/ath9k/ar9003_phy.c |   16 ++++++++++------
> > >  drivers/net/wireless/ath/ath9k/hw.c         |    7 ++++++-
> > >  drivers/net/wireless/ath/ath9k/reg.h        |    2 ++
> > >  3 files changed, 18 insertions(+), 7 deletions(-)
> > > 
> > > diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> > > index b34a9e9..4e35bda 100644
> > > --- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> > > +++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> > > @@ -390,14 +390,18 @@ static u32 ar9003_hw_compute_pll_control(struct ath_hw *ah,
> > >  {
> > >  	u32 pll;
> > >  
> > > -	pll = SM(0x5, AR_RTC_9300_PLL_REFDIV);
> > > +	if (AR_SREV_9485(ah))
> > > +		pll = 0x142c;
> > > +	else {
> > > +		pll = SM(0x5, AR_RTC_9300_PLL_REFDIV);
> > >  
> > > -	if (chan && IS_CHAN_HALF_RATE(chan))
> > > -		pll |= SM(0x1, AR_RTC_9300_PLL_CLKSEL);
> > > -	else if (chan && IS_CHAN_QUARTER_RATE(chan))
> > > -		pll |= SM(0x2, AR_RTC_9300_PLL_CLKSEL);
> > > +		if (chan && IS_CHAN_HALF_RATE(chan))
> > > +			pll |= SM(0x1, AR_RTC_9300_PLL_CLKSEL);
> > > +		else if (chan && IS_CHAN_QUARTER_RATE(chan))
> > > +			pll |= SM(0x2, AR_RTC_9300_PLL_CLKSEL);
> > >  
> > > -	pll |= SM(0x2c, AR_RTC_9300_PLL_DIV);
> > > +		pll |= SM(0x2c, AR_RTC_9300_PLL_DIV);
> > > +	}
> > >  
> > >  	return pll;
> > >  }
> > NACK for this part. Take a look at what gets set for the older chips:
> > 
> > 0x5 << AR_RTC_9300_PLL_REFDIV_S == 0x1400
> > 0x2c << AR_RTC_9300_PLL_DIV_S == 0x002c
> 
> True, but older ar9003 chips have half/quarter rate support (which is not
> implemented right now), in that case pll configuration would differ
> for AR9485.

Never mind, it will be the same even then. Will clean up this patch.
thanks for the review

vasanth

[PATCH 11/26] ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 from an array for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_phy.c |   25 ++++++++++++++++++++++++-
 1 files changed, 24 insertions(+), 1 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
index 4e35bda..4739af1 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
@@ -25,6 +25,24 @@ static const int cycpwrThr1_table[] =
 /* level:  0   1   2   3   4   5   6   7   8  */
 	{ -6, -4, -2,  0,  2,  4,  6,  8 };     /* lvl 0-7, default 3 */
 
+/* Chansel table used by ar9485 */
+static const u32 ar9003_chansel_xtal_40M[] = {
+	0xa0ccbe,
+	0xa12213,
+	0xa17769,
+	0xa1ccbe,
+	0xa22213,
+	0xa27769,
+	0xa2ccbe,
+	0xa32213,
+	0xa37769,
+	0xa3ccbe,
+	0xa42213,
+	0xa47769,
+	0xa4ccbe,
+	0xa5998b,
+};
+
 /*
  * register values to turn OFDM weak signal detection OFF
  */
@@ -75,7 +93,12 @@ static int ar9003_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan)
 	freq = centers.synth_center;
 
 	if (freq < 4800) {     /* 2 GHz, fractional mode */
-		channelSel = CHANSEL_2G(freq);
+		if (AR_SREV_9485(ah)) {
+			int ichan = ieee80211_frequency_to_channel(freq);
+
+			channelSel = ar9003_chansel_xtal_40M[ichan - 1];
+		} else
+			channelSel = CHANSEL_2G(freq);
 		/* Set to 2G mode */
 		bMode = 1;
 	} else {
-- 
1.7.0.4

Re: [PATCH 11/26] ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 from an array for AR9485

[Felix Fietkau]

On 2010-12-01 8:32 AM, Vasanthakumar Thiagarajan wrote:
> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
> ---
>  drivers/net/wireless/ath/ath9k/ar9003_phy.c |   25 ++++++++++++++++++++++++-
>  1 files changed, 24 insertions(+), 1 deletions(-)
> 
> diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> index 4e35bda..4739af1 100644
> --- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> +++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> @@ -25,6 +25,24 @@ static const int cycpwrThr1_table[] =
>  /* level:  0   1   2   3   4   5   6   7   8  */
>  	{ -6, -4, -2,  0,  2,  4,  6,  8 };     /* lvl 0-7, default 3 */
>  
> +/* Chansel table used by ar9485 */
> +static const u32 ar9003_chansel_xtal_40M[] = {
> +	0xa0ccbe,
> +	0xa12213,
> +	0xa17769,
> +	0xa1ccbe,
> +	0xa22213,
> +	0xa27769,
> +	0xa2ccbe,
> +	0xa32213,
> +	0xa37769,
> +	0xa3ccbe,
> +	0xa42213,
> +	0xa47769,
> +	0xa4ccbe,
> +	0xa5998b,
> +};
> +
>  /*
>   * register values to turn OFDM weak signal detection OFF
>   */
> @@ -75,7 +93,12 @@ static int ar9003_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan)
>  	freq = centers.synth_center;
>  
>  	if (freq < 4800) {     /* 2 GHz, fractional mode */
> -		channelSel = CHANSEL_2G(freq);
> +		if (AR_SREV_9485(ah)) {
> +			int ichan = ieee80211_frequency_to_channel(freq);
> +
> +			channelSel = ar9003_chansel_xtal_40M[ichan - 1];
> +		} else
> +			channelSel = CHANSEL_2G(freq);
I looked at the values of this table, this is exactly the same as what
CHANSEL_2G() returns except that the table has an offset of -14.
Please use CHANSEL_2G(freq) - 14 for AR9485 and drop the table to avoid
adding more unnecessary hardcoded values.

- Felix

Re: [PATCH 11/26] ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 from an array for AR9485

[Vasanthakumar Thiagarajan]

On Wed, Dec 01, 2010 at 10:15:31PM +0530, Felix Fietkau wrote:
> On 2010-12-01 8:32 AM, Vasanthakumar Thiagarajan wrote:
> > Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
> > ---
> >  drivers/net/wireless/ath/ath9k/ar9003_phy.c |   25 ++++++++++++++++++++++++-
> >  1 files changed, 24 insertions(+), 1 deletions(-)
> > 
> > diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> > index 4e35bda..4739af1 100644
> > --- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> > +++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
> > @@ -25,6 +25,24 @@ static const int cycpwrThr1_table[] =
> >  /* level:  0   1   2   3   4   5   6   7   8  */
> >  	{ -6, -4, -2,  0,  2,  4,  6,  8 };     /* lvl 0-7, default 3 */
> >  
> > +/* Chansel table used by ar9485 */
> > +static const u32 ar9003_chansel_xtal_40M[] = {
> > +	0xa0ccbe,
> > +	0xa12213,
> > +	0xa17769,
> > +	0xa1ccbe,
> > +	0xa22213,
> > +	0xa27769,
> > +	0xa2ccbe,
> > +	0xa32213,
> > +	0xa37769,
> > +	0xa3ccbe,
> > +	0xa42213,
> > +	0xa47769,
> > +	0xa4ccbe,
> > +	0xa5998b,
> > +};
> > +
> >  /*
> >   * register values to turn OFDM weak signal detection OFF
> >   */
> > @@ -75,7 +93,12 @@ static int ar9003_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan)
> >  	freq = centers.synth_center;
> >  
> >  	if (freq < 4800) {     /* 2 GHz, fractional mode */
> > -		channelSel = CHANSEL_2G(freq);
> > +		if (AR_SREV_9485(ah)) {
> > +			int ichan = ieee80211_frequency_to_channel(freq);
> > +
> > +			channelSel = ar9003_chansel_xtal_40M[ichan - 1];
> > +		} else
> > +			channelSel = CHANSEL_2G(freq);
> I looked at the values of this table, this is exactly the same as what
> CHANSEL_2G() returns except that the table has an offset of -14.
> Please use CHANSEL_2G(freq) - 14 for AR9485 and drop the table to avoid
> adding more unnecessary hardcoded values.

Not exactly. See the following CHANSEL_2G(freq).

 a0cccc
 a12222
 a17777
 a1cccc
 a22222
 a27777
 a2cccc
 a32222
 a37777
 a3cccc
 a42222
 a47777
 a4cccc
 a52222

Vasanth

[PATCH 12/26] ath9k_hw: Add a helper function to get spur channel pointer from cal data for AR9003 family

[Vasanthakumar Thiagarajan]

This helper function would be used for AR9485.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |   10 ++++++++++
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.h |    1 +
 2 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index 6cbfbfa..c85b97e 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -4758,6 +4758,16 @@ s32 ar9003_hw_get_rx_gain_idx(struct ath_hw *ah)
 	return (eep->baseEepHeader.txrxgain) & 0xf; /* bits 3:0 */
 }
 
+u8 *ar9003_get_spur_chan_ptr(struct ath_hw *ah, bool is_2ghz)
+{
+	struct ar9300_eeprom *eep = &ah->eeprom.ar9300_eep;
+
+	if (is_2ghz)
+		return eep->modalHeader2G.spurChans;
+	else
+		return eep->modalHeader5G.spurChans;
+}
+
 const struct eeprom_ops eep_ar9300_ops = {
 	.check_eeprom = ath9k_hw_ar9300_check_eeprom,
 	.get_eeprom = ath9k_hw_ar9300_get_eeprom,
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.h b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.h
index d189c87..cf3e145 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.h
@@ -348,4 +348,5 @@ struct ar9300_eeprom {
 s32 ar9003_hw_get_tx_gain_idx(struct ath_hw *ah);
 s32 ar9003_hw_get_rx_gain_idx(struct ath_hw *ah);
 
+u8 *ar9003_get_spur_chan_ptr(struct ath_hw *ah, bool is_2ghz);
 #endif
-- 
1.7.0.4

[PATCH 13/26] ath9k: Read spur channel information from eeprom for AR9485

[Vasanthakumar Thiagarajan]

Also spur channel count and range is different for AR9485.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_phy.c |   35 ++++++++++++++++++++++++--
 1 files changed, 32 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
index 4739af1..e461723 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
@@ -154,21 +154,50 @@ static void ar9003_hw_spur_mitigate_mrc_cck(struct ath_hw *ah,
 	static const u32 spur_freq[4] = { 2420, 2440, 2464, 2480 };
 	int cur_bb_spur, negative = 0, cck_spur_freq;
 	int i;
+	int range, max_spur_cnts, synth_freq;
+	u8 *spur_fbin_ptr = NULL;
 
 	/*
 	 * Need to verify range +/- 10 MHz in control channel, otherwise spur
 	 * is out-of-band and can be ignored.
 	 */
 
-	for (i = 0; i < 4; i++) {
+	if (AR_SREV_9485(ah)) {
+		spur_fbin_ptr = ar9003_get_spur_chan_ptr(ah,
+							 IS_CHAN_2GHZ(chan));
+		if (spur_fbin_ptr[0] == 0) /* No spur */
+			return;
+		max_spur_cnts = 5;
+		if (IS_CHAN_HT40(chan)) {
+			range = 19;
+			if (REG_READ_FIELD(ah, AR_PHY_GEN_CTRL,
+					   AR_PHY_GC_DYN2040_PRI_CH) == 0)
+				synth_freq = chan->channel + 10;
+			else
+				synth_freq = chan->channel - 10;
+		} else {
+			range = 10;
+			synth_freq = chan->channel;
+		}
+	} else {
+		range = 10;
+		max_spur_cnts = 4;
+		synth_freq = chan->channel;
+	}
+
+	for (i = 0; i < max_spur_cnts; i++) {
 		negative = 0;
-		cur_bb_spur = spur_freq[i] - chan->channel;
+		if (AR_SREV_9485(ah))
+			cur_bb_spur = FBIN2FREQ(spur_fbin_ptr[i],
+					IS_CHAN_2GHZ(chan)) - synth_freq;
+		else
+			cur_bb_spur = spur_freq[i] - synth_freq;
 
 		if (cur_bb_spur < 0) {
 			negative = 1;
 			cur_bb_spur = -cur_bb_spur;
 		}
-		if (cur_bb_spur < 10) {
+		if (cur_bb_spur < range) {
 			cck_spur_freq = (int)((cur_bb_spur << 19) / 11);
 
 			if (negative == 1)
-- 
1.7.0.4

[PATCH 14/26] ath9k_hw: Configure xpa bias level for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |   12 +++++++++---
 drivers/net/wireless/ath/ath9k/ar9003_phy.h    |    4 ++++
 2 files changed, 13 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index c85b97e..02b6150 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -3449,9 +3449,15 @@ static s32 ar9003_hw_xpa_bias_level_get(struct ath_hw *ah, bool is2ghz)
 static void ar9003_hw_xpa_bias_level_apply(struct ath_hw *ah, bool is2ghz)
 {
 	int bias = ar9003_hw_xpa_bias_level_get(ah, is2ghz);
-	REG_RMW_FIELD(ah, AR_CH0_TOP, AR_CH0_TOP_XPABIASLVL, bias);
-	REG_RMW_FIELD(ah, AR_CH0_THERM, AR_CH0_THERM_XPABIASLVL_MSB, bias >> 2);
-	REG_RMW_FIELD(ah, AR_CH0_THERM, AR_CH0_THERM_XPASHORT2GND, 1);
+
+	if (AR_SREV_9485(ah))
+		REG_RMW_FIELD(ah, AR_CH0_TOP2, AR_CH0_TOP2_XPABIASLVL, bias);
+	else {
+		REG_RMW_FIELD(ah, AR_CH0_TOP, AR_CH0_TOP_XPABIASLVL, bias);
+		REG_RMW_FIELD(ah, AR_CH0_THERM, AR_CH0_THERM_XPABIASLVL_MSB,
+			      bias >> 2);
+		REG_RMW_FIELD(ah, AR_CH0_THERM, AR_CH0_THERM_XPASHORT2GND, 1);
+	}
 }
 
 static u32 ar9003_hw_ant_ctrl_common_get(struct ath_hw *ah, bool is2ghz)
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
index 3394dfe..b772081 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -584,6 +584,10 @@
 #define AR_PHY_65NM_CH2_RXTX1       0x16900
 #define AR_PHY_65NM_CH2_RXTX2       0x16904
 
+#define AR_CH0_TOP2 (AR_SREV_9485(ah) ? 0x00016284 : 0x0001628c)
+#define AR_CH0_TOP2_XPABIASLVL		0xf000
+#define AR_CH0_TOP2_XPABIASLVL_S	12
+
 #define AR_PHY_RX1DB_BIQUAD_LONG_SHIFT		0x00380000
 #define AR_PHY_RX1DB_BIQUAD_LONG_SHIFT_S	19
 #define AR_PHY_RX6DB_BIQUAD_LONG_SHIFT		0x00c00000
-- 
1.7.0.4

[PATCH 15/26] ath9k_hw: Read and configure antenna diversity control for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |   24 ++++++++++++++++++++----
 drivers/net/wireless/ath/ath9k/ar9003_phy.h    |   10 ++++++++++
 2 files changed, 30 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index 02b6150..9ce6846 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -3031,6 +3031,8 @@ static u32 ath9k_hw_ar9300_get_eeprom(struct ath_hw *ah,
 		return !!(pBase->featureEnable & BIT(5));
 	case EEP_CHAIN_MASK_REDUCE:
 		return (pBase->miscConfiguration >> 0x3) & 0x1;
+	case EEP_ANT_DIV_CTL1:
+		return le32_to_cpu(eep->base_ext1.ant_div_control);
 	default:
 		return 0;
 	}
@@ -3512,11 +3514,25 @@ static void ar9003_hw_ant_ctrl_apply(struct ath_hw *ah, bool is2ghz)
 	value = ar9003_hw_ant_ctrl_chain_get(ah, 0, is2ghz);
 	REG_RMW_FIELD(ah, AR_PHY_SWITCH_CHAIN_0, AR_SWITCH_TABLE_ALL, value);
 
-	value = ar9003_hw_ant_ctrl_chain_get(ah, 1, is2ghz);
-	REG_RMW_FIELD(ah, AR_PHY_SWITCH_CHAIN_1, AR_SWITCH_TABLE_ALL, value);
+	if (!AR_SREV_9485(ah)) {
+		value = ar9003_hw_ant_ctrl_chain_get(ah, 1, is2ghz);
+		REG_RMW_FIELD(ah, AR_PHY_SWITCH_CHAIN_1, AR_SWITCH_TABLE_ALL,
+			      value);
 
-	value = ar9003_hw_ant_ctrl_chain_get(ah, 2, is2ghz);
-	REG_RMW_FIELD(ah, AR_PHY_SWITCH_CHAIN_2, AR_SWITCH_TABLE_ALL, value);
+		value = ar9003_hw_ant_ctrl_chain_get(ah, 2, is2ghz);
+		REG_RMW_FIELD(ah, AR_PHY_SWITCH_CHAIN_2, AR_SWITCH_TABLE_ALL,
+			      value);
+	}
+
+	if (AR_SREV_9485(ah)) {
+		value = ath9k_hw_ar9300_get_eeprom(ah, EEP_ANT_DIV_CTL1);
+		REG_RMW_FIELD(ah, AR_PHY_MC_GAIN_CTRL, AR_ANT_DIV_CTRL_ALL,
+			      value);
+		REG_RMW_FIELD(ah, AR_PHY_MC_GAIN_CTRL, AR_ANT_DIV_ENABLE,
+			      value >> 6);
+		REG_RMW_FIELD(ah, AR_PHY_CCK_DETECT, AR_FAST_DIV_ENABLE,
+			      value >> 7);
+	}
 }
 
 static void ar9003_hw_drive_strength_apply(struct ath_hw *ah)
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
index b772081..6e0d4ad 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -260,7 +260,13 @@
 #define AR_PHY_CCA_0            (AR_AGC_BASE + 0x1c)
 #define AR_PHY_EXT_CCA0         (AR_AGC_BASE + 0x20)
 #define AR_PHY_RESTART          (AR_AGC_BASE + 0x24)
+
 #define AR_PHY_MC_GAIN_CTRL     (AR_AGC_BASE + 0x28)
+#define AR_ANT_DIV_CTRL_ALL	0x7e000000
+#define AR_ANT_DIV_CTRL_ALL_S	25
+#define AR_ANT_DIV_ENABLE	0x1000000
+#define AR_ANT_DIV_ENABLE_S	24
+
 #define AR_PHY_EXTCHN_PWRTHR1   (AR_AGC_BASE + 0x2c)
 #define AR_PHY_EXT_CHN_WIN      (AR_AGC_BASE + 0x30)
 #define AR_PHY_20_40_DET_THR    (AR_AGC_BASE + 0x34)
@@ -271,7 +277,11 @@
 #define AR_PHY_RX_GAIN_BOUNDS_2 (AR_AGC_BASE + 0x48)
 #define AR_PHY_RSSI_0           (AR_AGC_BASE + 0x180)
 #define AR_PHY_SPUR_CCK_REP0    (AR_AGC_BASE + 0x184)
+
 #define AR_PHY_CCK_DETECT       (AR_AGC_BASE + 0x1c0)
+#define AR_FAST_DIV_ENABLE	0x2000
+#define AR_FAST_DIV_ENABLE_S	13
+
 #define AR_PHY_DAG_CTRLCCK      (AR_AGC_BASE + 0x1c4)
 #define AR_PHY_IQCORR_CTRL_CCK  (AR_AGC_BASE + 0x1c8)
 
-- 
1.7.0.4

[PATCH 16/26] ath9k_hw: Configure attenuation control only for chain 0 on AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |    6 +++++-
 1 files changed, 5 insertions(+), 1 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index 9ce6846..71316ec 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -3639,9 +3639,13 @@ static void ar9003_hw_atten_apply(struct ath_hw *ah, struct ath9k_channel *chan)
 					  AR_PHY_EXT_ATTEN_CTL_1,
 					  AR_PHY_EXT_ATTEN_CTL_2,
 					 };
+	u8 max_chains = AR9300_MAX_CHAINS;
+
+	if (AR_SREV_9485(ah))
+		max_chains = 1;
 
 	/* Test value. if 0 then attenuation is unused. Don't load anything. */
-	for (i = 0; i < 3; i++) {
+	for (i = 0; i < max_chains; i++) {
 		value = ar9003_hw_atten_chain_get(ah, i, chan);
 		REG_RMW_FIELD(ah, ext_atten_reg[i],
 			      AR_PHY_EXT_ATTEN_CTL_XATTEN1_DB, value);
-- 
1.7.0.4

Re: [PATCH 16/26] ath9k_hw: Configure attenuation control only for chain 0 on AR9485

[Felix Fietkau]

On 2010-12-01 8:32 AM, Vasanthakumar Thiagarajan wrote:
> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
> ---
>  drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |    6 +++++-
>  1 files changed, 5 insertions(+), 1 deletions(-)
> 
> diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
> index 9ce6846..71316ec 100644
> --- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
> +++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
> @@ -3639,9 +3639,13 @@ static void ar9003_hw_atten_apply(struct ath_hw *ah, struct ath9k_channel *chan)
>  					  AR_PHY_EXT_ATTEN_CTL_1,
>  					  AR_PHY_EXT_ATTEN_CTL_2,
>  					 };
> +	u8 max_chains = AR9300_MAX_CHAINS;
> +
> +	if (AR_SREV_9485(ah))
> +		max_chains = 1;
>  
>  	/* Test value. if 0 then attenuation is unused. Don't load anything. */
> -	for (i = 0; i < 3; i++) {
> +	for (i = 0; i < max_chains; i++) {
>  		value = ar9003_hw_atten_chain_get(ah, i, chan);
>  		REG_RMW_FIELD(ah, ext_atten_reg[i],
>  			      AR_PHY_EXT_ATTEN_CTL_XATTEN1_DB, value);
Since the issue of having second/third chain registers unimplemented in
certain chips is going to be the same on AR9344 and other WiSoC chips as
well, how about adding an ath9k_hw variable max_hw_chains and using that
wherever extended chain registers would be accessed.
That would save us from having to throw around new SREV checks over and
over again for the same issue.

- Felix

Re: [PATCH 16/26] ath9k_hw: Configure attenuation control only for chain 0 on AR9485

[Vasanthakumar Thiagarajan]

On Wed, Dec 01, 2010 at 10:20:50PM +0530, Felix Fietkau wrote:
> On 2010-12-01 8:32 AM, Vasanthakumar Thiagarajan wrote:
> > Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
> > ---
> >  drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |    6 +++++-
> >  1 files changed, 5 insertions(+), 1 deletions(-)
> > 
> > diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
> > index 9ce6846..71316ec 100644
> > --- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
> > +++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
> > @@ -3639,9 +3639,13 @@ static void ar9003_hw_atten_apply(struct ath_hw *ah, struct ath9k_channel *chan)
> >  					  AR_PHY_EXT_ATTEN_CTL_1,
> >  					  AR_PHY_EXT_ATTEN_CTL_2,
> >  					 };
> > +	u8 max_chains = AR9300_MAX_CHAINS;
> > +
> > +	if (AR_SREV_9485(ah))
> > +		max_chains = 1;
> >  
> >  	/* Test value. if 0 then attenuation is unused. Don't load anything. */
> > -	for (i = 0; i < 3; i++) {
> > +	for (i = 0; i < max_chains; i++) {
> >  		value = ar9003_hw_atten_chain_get(ah, i, chan);
> >  		REG_RMW_FIELD(ah, ext_atten_reg[i],
> >  			      AR_PHY_EXT_ATTEN_CTL_XATTEN1_DB, value);
> Since the issue of having second/third chain registers unimplemented in
> certain chips is going to be the same on AR9344 and other WiSoC chips as
> well, how about adding an ath9k_hw variable max_hw_chains and using that
> wherever extended chain registers would be accessed.
> That would save us from having to throw around new SREV checks over and
> over again for the same issue.

makes sense.

Vasanth

[PATCH 17/26] ath9k_hw: Configure internal regulator for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |   89 ++++++++++++++++++++----
 drivers/net/wireless/ath/ath9k/ar9003_phy.h    |    8 ++
 2 files changed, 82 insertions(+), 15 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index 71316ec..c6be177 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -3656,29 +3656,88 @@ static void ar9003_hw_atten_apply(struct ath_hw *ah, struct ath9k_channel *chan)
 	}
 }
 
+static bool is_pmu_set(struct ath_hw *ah, int pmu_set, u32 pmu_reg)
+{
+	int timeout = 100;
+
+	while (pmu_set != REG_READ(ah, pmu_reg)) {
+		if (timeout-- == 0)
+			return false;
+		REG_WRITE(ah, pmu_reg, pmu_set);
+		udelay(10);
+	}
+
+	return true;
+}
+
 static void ar9003_hw_internal_regulator_apply(struct ath_hw *ah)
 {
 	int internal_regulator =
 		ath9k_hw_ar9300_get_eeprom(ah, EEP_INTERNAL_REGULATOR);
 
 	if (internal_regulator) {
-		/* Internal regulator is ON. Write swreg register. */
-		int swreg = ath9k_hw_ar9300_get_eeprom(ah, EEP_SWREG);
-		REG_WRITE(ah, AR_RTC_REG_CONTROL1,
-		REG_READ(ah, AR_RTC_REG_CONTROL1) &
-			 (~AR_RTC_REG_CONTROL1_SWREG_PROGRAM));
-		REG_WRITE(ah, AR_RTC_REG_CONTROL0, swreg);
-		/* Set REG_CONTROL1.SWREG_PROGRAM */
-		REG_WRITE(ah, AR_RTC_REG_CONTROL1,
-			  REG_READ(ah,
-				   AR_RTC_REG_CONTROL1) |
-				   AR_RTC_REG_CONTROL1_SWREG_PROGRAM);
+		if (AR_SREV_9485(ah)) {
+			int reg_pmu_set;
+
+			reg_pmu_set = REG_READ(ah, AR_PHY_PMU2) & ~AR_PHY_PMU2_PGM;
+			REG_WRITE(ah, AR_PHY_PMU2, reg_pmu_set);
+			if (!is_pmu_set(ah, AR_PHY_PMU2, reg_pmu_set))
+				return;
+
+			reg_pmu_set = (5 << 1) | (7 << 4) | (1 << 8) |
+				      (7 << 14) | (6 << 17) | (1 << 20) |
+				      (3 << 24) | (1 << 28);
+
+			REG_WRITE(ah, AR_PHY_PMU1, reg_pmu_set);
+			if (!is_pmu_set(ah, AR_PHY_PMU1, reg_pmu_set))
+				return;
+
+			reg_pmu_set = (REG_READ(ah, AR_PHY_PMU2) & ~0xFFC00000)
+					| (4 << 26);
+			REG_WRITE(ah, AR_PHY_PMU2, reg_pmu_set);
+			if (!is_pmu_set(ah, AR_PHY_PMU2, reg_pmu_set))
+				return;
+
+			reg_pmu_set = (REG_READ(ah, AR_PHY_PMU2) & ~0x00200000)
+					| (1 << 21);
+			REG_WRITE(ah, AR_PHY_PMU2, reg_pmu_set);
+			if (!is_pmu_set(ah, AR_PHY_PMU2, reg_pmu_set))
+				return;
+		} else {
+			/* Internal regulator is ON. Write swreg register. */
+			int swreg = ath9k_hw_ar9300_get_eeprom(ah, EEP_SWREG);
+			REG_WRITE(ah, AR_RTC_REG_CONTROL1,
+				  REG_READ(ah, AR_RTC_REG_CONTROL1) &
+				  (~AR_RTC_REG_CONTROL1_SWREG_PROGRAM));
+			REG_WRITE(ah, AR_RTC_REG_CONTROL0, swreg);
+			/* Set REG_CONTROL1.SWREG_PROGRAM */
+			REG_WRITE(ah, AR_RTC_REG_CONTROL1,
+				  REG_READ(ah,
+					   AR_RTC_REG_CONTROL1) |
+					   AR_RTC_REG_CONTROL1_SWREG_PROGRAM);
+		}
 	} else {
-		REG_WRITE(ah, AR_RTC_SLEEP_CLK,
-			  (REG_READ(ah,
-				    AR_RTC_SLEEP_CLK) |
-				    AR_RTC_FORCE_SWREG_PRD));
+		if (AR_SREV_9485(ah)) {
+			REG_RMW_FIELD(ah, AR_PHY_PMU2, AR_PHY_PMU2_PGM, 0);
+			while (REG_READ_FIELD(ah, AR_PHY_PMU2,
+					      AR_PHY_PMU2_PGM))
+				udelay(10);
+
+			REG_RMW_FIELD(ah, AR_PHY_PMU1, AR_PHY_PMU1_PWD, 0x1);
+			while (!REG_READ_FIELD(ah, AR_PHY_PMU1,
+					       AR_PHY_PMU1_PWD))
+				udelay(10);
+			REG_RMW_FIELD(ah, AR_PHY_PMU2, AR_PHY_PMU2_PGM, 0x1);
+			while (!REG_READ_FIELD(ah, AR_PHY_PMU2,
+					      AR_PHY_PMU2_PGM))
+				udelay(10);
+		} else
+			REG_WRITE(ah, AR_RTC_SLEEP_CLK,
+				  (REG_READ(ah,
+				   AR_RTC_SLEEP_CLK) |
+				   AR_RTC_FORCE_SWREG_PRD));
 	}
+
 }
 
 static void ath9k_hw_ar9300_set_board_values(struct ath_hw *ah,
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
index 6e0d4ad..8de3ffd 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -598,6 +598,14 @@
 #define AR_CH0_TOP2_XPABIASLVL		0xf000
 #define AR_CH0_TOP2_XPABIASLVL_S	12
 
+#define AR_PHY_PMU1		0x16c40
+#define AR_PHY_PMU1_PWD		0x1
+#define AR_PHY_PMU1_PWD_S	0
+
+#define AR_PHY_PMU2		0x16c44
+#define AR_PHY_PMU2_PGM		0x00200000
+#define AR_PHY_PMU2_PGM_S	21
+
 #define AR_PHY_RX1DB_BIQUAD_LONG_SHIFT		0x00380000
 #define AR_PHY_RX1DB_BIQUAD_LONG_SHIFT_S	19
 #define AR_PHY_RX6DB_BIQUAD_LONG_SHIFT		0x00c00000
-- 
1.7.0.4

[PATCH 18/26] ath9k_hw: Read and configure turnning caps to regulate freq accuracy

[Vasanthakumar Thiagarajan]

Right now it is done for only AR9485, will be done for ar9003 also
after proper testing.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |   16 ++++++++++++++++
 drivers/net/wireless/ath/ath9k/ar9003_phy.h    |    6 ++++++
 2 files changed, 22 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index c6be177..9d9d637 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -3740,6 +3740,20 @@ static void ar9003_hw_internal_regulator_apply(struct ath_hw *ah)
 
 }
 
+static void ar9003_hw_apply_tuning_caps(struct ath_hw *ah)
+{
+	struct ar9300_eeprom *eep = &ah->eeprom.ar9300_eep;
+	u8 tuning_caps_param = eep->baseEepHeader.params_for_tuning_caps[0];
+
+	if (eep->baseEepHeader.featureEnable & 0x40) {
+		tuning_caps_param &= 0x7f;
+		REG_RMW_FIELD(ah, AR_CH0_XTAL, AR_CH0_XTAL_CAPINDAC,
+			      tuning_caps_param);
+		REG_RMW_FIELD(ah, AR_CH0_XTAL, AR_CH0_XTAL_CAPOUTDAC,
+			      tuning_caps_param);
+	}
+}
+
 static void ath9k_hw_ar9300_set_board_values(struct ath_hw *ah,
 					     struct ath9k_channel *chan)
 {
@@ -3748,6 +3762,8 @@ static void ath9k_hw_ar9300_set_board_values(struct ath_hw *ah,
 	ar9003_hw_drive_strength_apply(ah);
 	ar9003_hw_atten_apply(ah, chan);
 	ar9003_hw_internal_regulator_apply(ah);
+	if (AR_SREV_9485(ah))
+		ar9003_hw_apply_tuning_caps(ah);
 }
 
 static void ath9k_hw_ar9300_set_addac(struct ath_hw *ah,
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
index 8de3ffd..4c64eb1 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -598,6 +598,12 @@
 #define AR_CH0_TOP2_XPABIASLVL		0xf000
 #define AR_CH0_TOP2_XPABIASLVL_S	12
 
+#define AR_CH0_XTAL		(AR_SREV_9485(ah) ? 0x16290 : 0x16294)
+#define AR_CH0_XTAL_CAPINDAC	0x7f000000
+#define AR_CH0_XTAL_CAPINDAC_S	24
+#define AR_CH0_XTAL_CAPOUTDAC	0x00fe0000
+#define AR_CH0_XTAL_CAPOUTDAC_S	17
+
 #define AR_PHY_PMU1		0x16c40
 #define AR_PHY_PMU1_PWD		0x1
 #define AR_PHY_PMU1_PWD_S	0
-- 
1.7.0.4

[PATCH 19/26] ath9k_hw: Configure power control only for chain 0 on AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c |   28 +++++++++++++----------
 1 files changed, 16 insertions(+), 12 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index 9d9d637..6115f36 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -4277,23 +4277,27 @@ static int ar9003_hw_power_control_override(struct ath_hw *ah,
 	REG_RMW(ah, AR_PHY_TPC_11_B0,
 		(correction[0] << AR_PHY_TPC_OLPC_GAIN_DELTA_S),
 		AR_PHY_TPC_OLPC_GAIN_DELTA);
-	REG_RMW(ah, AR_PHY_TPC_11_B1,
-		(correction[1] << AR_PHY_TPC_OLPC_GAIN_DELTA_S),
-		AR_PHY_TPC_OLPC_GAIN_DELTA);
-	REG_RMW(ah, AR_PHY_TPC_11_B2,
-		(correction[2] << AR_PHY_TPC_OLPC_GAIN_DELTA_S),
-		AR_PHY_TPC_OLPC_GAIN_DELTA);
+	if (!AR_SREV_9485(ah)) {
+		REG_RMW(ah, AR_PHY_TPC_11_B1,
+			(correction[1] << AR_PHY_TPC_OLPC_GAIN_DELTA_S),
+			AR_PHY_TPC_OLPC_GAIN_DELTA);
+		REG_RMW(ah, AR_PHY_TPC_11_B2,
+			(correction[2] << AR_PHY_TPC_OLPC_GAIN_DELTA_S),
+			AR_PHY_TPC_OLPC_GAIN_DELTA);
+	}
 
 	/* enable open loop power control on chip */
 	REG_RMW(ah, AR_PHY_TPC_6_B0,
 		(3 << AR_PHY_TPC_6_ERROR_EST_MODE_S),
 		AR_PHY_TPC_6_ERROR_EST_MODE);
-	REG_RMW(ah, AR_PHY_TPC_6_B1,
-		(3 << AR_PHY_TPC_6_ERROR_EST_MODE_S),
-		AR_PHY_TPC_6_ERROR_EST_MODE);
-	REG_RMW(ah, AR_PHY_TPC_6_B2,
-		(3 << AR_PHY_TPC_6_ERROR_EST_MODE_S),
-		AR_PHY_TPC_6_ERROR_EST_MODE);
+	if (!AR_SREV_9485(ah)) {
+		REG_RMW(ah, AR_PHY_TPC_6_B1,
+			(3 << AR_PHY_TPC_6_ERROR_EST_MODE_S),
+			AR_PHY_TPC_6_ERROR_EST_MODE);
+		REG_RMW(ah, AR_PHY_TPC_6_B2,
+			(3 << AR_PHY_TPC_6_ERROR_EST_MODE_S),
+			AR_PHY_TPC_6_ERROR_EST_MODE);
+	}
 
 	/*
 	 * enable temperature compensation
-- 
1.7.0.4

Re: [PATCH 19/26] ath9k_hw: Configure power control only for chain 0 on AR9485

[Felix Fietkau]

On 2010-12-01 8:32 AM, Vasanthakumar Thiagarajan wrote:
> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
See my other comment about attenuation control.

- Felix

[PATCH 20/26] ath9k_hw: Program appropriate chianmask for AR9485 before starting AGC/IQ cal

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_calib.c |    4 +++-
 1 files changed, 3 insertions(+), 1 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_calib.c b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
index 4c94c9e..f218613 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_calib.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
@@ -723,7 +723,9 @@ static bool ar9003_hw_init_cal(struct ath_hw *ah,
 	val = REG_READ(ah, AR_ENT_OTP);
 	ath_print(common, ATH_DBG_CALIBRATE, "ath9k: AR_ENT_OTP 0x%x\n", val);
 
-	if (val & AR_ENT_OTP_CHAIN2_DISABLE)
+	if (AR_SREV_9485(ah))
+		ar9003_hw_set_chain_masks(ah, 0x1, 0x1);
+	else if (val & AR_ENT_OTP_CHAIN2_DISABLE)
 		ar9003_hw_set_chain_masks(ah, 0x3, 0x3);
 	else
 		/*
-- 
1.7.0.4

[PATCH 21/26] ath9k_hw: Define IQcal correction coefficient registers using index

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_calib.c |   10 +++++-----
 drivers/net/wireless/ath/ath9k/ar9003_phy.h   |    8 +++++---
 2 files changed, 10 insertions(+), 8 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_calib.c b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
index f218613..c3867cd 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_calib.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
@@ -608,11 +608,6 @@ static void ar9003_hw_tx_iq_cal(struct ath_hw *ah)
 		AR_PHY_TX_IQCAL_STATUS_B1,
 		AR_PHY_TX_IQCAL_STATUS_B2,
 	};
-	static const u32 tx_corr_coeff[AR9300_MAX_CHAINS] = {
-		AR_PHY_TX_IQCAL_CORR_COEFF_01_B0,
-		AR_PHY_TX_IQCAL_CORR_COEFF_01_B1,
-		AR_PHY_TX_IQCAL_CORR_COEFF_01_B2,
-	};
 	static const u32 rx_corr[AR9300_MAX_CHAINS] = {
 		AR_PHY_RX_IQCAL_CORR_B0,
 		AR_PHY_RX_IQCAL_CORR_B1,
@@ -623,11 +618,16 @@ static void ar9003_hw_tx_iq_cal(struct ath_hw *ah)
 		AR_PHY_CHAN_INFO_TAB_1,
 		AR_PHY_CHAN_INFO_TAB_2,
 	};
+	u32 tx_corr_coeff[AR9300_MAX_CHAINS];
 	s32 iq_res[6];
 	s32 iqc_coeff[2];
 	s32 i, j;
 	u32 num_chains = 0;
 
+	tx_corr_coeff[0] = AR_PHY_TX_IQCAL_CORR_COEFF_B0(0);
+	tx_corr_coeff[1] = AR_PHY_TX_IQCAL_CORR_COEFF_B1(0);
+	tx_corr_coeff[2] = AR_PHY_TX_IQCAL_CORR_COEFF_B2(0);
+
 	for (i = 0; i < AR9300_MAX_CHAINS; i++) {
 		if (ah->txchainmask & (1 << i))
 			num_chains++;
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
index 4c64eb1..abb4ec1 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -549,7 +549,9 @@
 #define AR_PHY_TX_IQCAL_CONTROL_1   (AR_SM_BASE + 0x448)
 #define AR_PHY_TX_IQCAL_START       (AR_SM_BASE + 0x440)
 #define AR_PHY_TX_IQCAL_STATUS_B0   (AR_SM_BASE + 0x48c)
-#define AR_PHY_TX_IQCAL_CORR_COEFF_01_B0    (AR_SM_BASE + 0x450)
+#define AR_PHY_TX_IQCAL_CORR_COEFF_B0(_i)    (AR_SM_BASE + \
+					     (AR_SREV_9485(ah) ? \
+					      0x3d0 : 0x450) + ((_i) << 2))
 
 #define AR_PHY_WATCHDOG_STATUS      (AR_SM_BASE + 0x5c0)
 #define AR_PHY_WATCHDOG_CTL_1       (AR_SM_BASE + 0x5c4)
@@ -813,7 +815,7 @@
 #define AR_PHY_TPC_11_B1         (AR_SM1_BASE + 0x220)
 #define AR_PHY_PDADC_TAB_1       (AR_SM1_BASE + 0x240)
 #define AR_PHY_TX_IQCAL_STATUS_B1   (AR_SM1_BASE + 0x48c)
-#define AR_PHY_TX_IQCAL_CORR_COEFF_01_B1    (AR_SM1_BASE + 0x450)
+#define AR_PHY_TX_IQCAL_CORR_COEFF_B1(_i)    (AR_SM_BASE + 0x450 + ((_i) << 2))
 
 /*
  * Channel 2 Register Map
@@ -866,7 +868,7 @@
 #define AR_PHY_TPC_11_B2         (AR_SM2_BASE + 0x220)
 #define AR_PHY_PDADC_TAB_2       (AR_SM2_BASE + 0x240)
 #define AR_PHY_TX_IQCAL_STATUS_B2   (AR_SM2_BASE + 0x48c)
-#define AR_PHY_TX_IQCAL_CORR_COEFF_01_B2    (AR_SM2_BASE + 0x450)
+#define AR_PHY_TX_IQCAL_CORR_COEFF_B2(_i)    (AR_SM2_BASE + 0x450 + ((_i) << 2))
 
 #define AR_PHY_TX_IQCAL_STATUS_B2_FAILED    0x00000001
 
-- 
1.7.0.4

[PATCH 22/26] ath9k_hw: Add IQ cal changes for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_calib.c |  242 ++++++++++++++++++++++++-
 drivers/net/wireless/ath/ath9k/ar9003_phy.h   |   16 ++-
 2 files changed, 255 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_calib.c b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
index c3867cd..799906f 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_calib.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
@@ -18,6 +18,16 @@
 #include "hw-ops.h"
 #include "ar9003_phy.h"
 
+#define MPASS	3
+#define MAX_MEASUREMENT	8
+#define MAX_DIFFERENCE	10
+
+struct coeff {
+	int mag_coeff[AR9300_MAX_CHAINS][MAX_MEASUREMENT][MPASS];
+	int phs_coeff[AR9300_MAX_CHAINS][MAX_MEASUREMENT][MPASS];
+	int iqc_coeff[2];
+};
+
 enum ar9003_cal_types {
 	IQ_MISMATCH_CAL = BIT(0),
 	TEMP_COMP_CAL = BIT(1),
@@ -714,6 +724,229 @@ TX_IQ_CAL_FAILED:
 	ath_print(common, ATH_DBG_CALIBRATE, "Tx IQ Cal failed\n");
 }
 
+static bool ar9003_hw_compute_closest_pass_and_avg(int *mp_coeff, int *mp_avg)
+{
+	int diff[MPASS];
+
+	diff[0] = abs(mp_coeff[0] - mp_coeff[1]);
+	diff[1] = abs(mp_coeff[1] - mp_coeff[2]);
+	diff[2] = abs(mp_coeff[2] - mp_coeff[0]);
+
+	if (diff[0] > MAX_MEASUREMENT &&
+	    diff[1] > MAX_MEASUREMENT &&
+	    diff[2] > MAX_MEASUREMENT)
+		return false;
+
+	if (diff[0] <= diff[1] && diff[0] <= diff[2])
+		*mp_avg = (mp_coeff[0] + mp_coeff[1]) / 2;
+	else if (diff[1] <= diff[2])
+		*mp_avg = (mp_coeff[1] + mp_coeff[2]) / 2;
+	else
+		*mp_avg = (mp_coeff[2] + mp_coeff[0]) / 2;
+
+	return true;
+}
+
+static void ar9003_hw_tx_iqcal_load_avg_2_passes(struct ath_hw *ah,
+						 u8 num_chains,
+						 struct coeff *coeff)
+{
+	struct ath_common *common = ath9k_hw_common(ah);
+	int i, im, nmeasurement;
+	int magnitude, phase;
+	u32 tx_corr_coeff[MAX_MEASUREMENT][AR9300_MAX_CHAINS];
+
+	memset(tx_corr_coeff, 0, sizeof(tx_corr_coeff));
+	for (i = 0; i < MAX_MEASUREMENT / 2; i++) {
+		tx_corr_coeff[i * 2][0] = tx_corr_coeff[(i * 2) + 1][0] =
+					AR_PHY_TX_IQCAL_CORR_COEFF_B0(i);
+		if (!AR_SREV_9485(ah)) {
+			tx_corr_coeff[i * 2][1] =
+			tx_corr_coeff[(i * 2) + 1][1] =
+					AR_PHY_TX_IQCAL_CORR_COEFF_B1(i);
+
+			tx_corr_coeff[i * 2][2] =
+			tx_corr_coeff[(i * 2) + 1][2] =
+					AR_PHY_TX_IQCAL_CORR_COEFF_B2(i);
+		}
+	}
+
+	/* Load the average of 2 passes */
+	for (i = 0; i < num_chains; i++) {
+		if (AR_SREV_9485(ah))
+			nmeasurement = REG_READ_FIELD(ah,
+					AR_PHY_TX_IQCAL_STATUS_B0_9485,
+					AR_PHY_CALIBRATED_GAINS_0);
+		else
+			nmeasurement = REG_READ_FIELD(ah,
+					AR_PHY_TX_IQCAL_STATUS_B0,
+					AR_PHY_CALIBRATED_GAINS_0);
+
+		if (nmeasurement > MAX_MEASUREMENT)
+			nmeasurement = MAX_MEASUREMENT;
+
+		for (im = 0; im < nmeasurement; im++) {
+			/*
+			 * Determine which 2 passes are closest and compute avg
+			 * magnitude
+			 */
+			if (!ar9003_hw_compute_closest_pass_and_avg(coeff->mag_coeff[i][im],
+								    &magnitude))
+				goto disable_txiqcal;
+
+			/*
+			 * Determine which 2 passes are closest and compute avg
+			 * phase
+			 */
+			if (!ar9003_hw_compute_closest_pass_and_avg(coeff->phs_coeff[i][im],
+								    &phase))
+				goto disable_txiqcal;
+
+			coeff->iqc_coeff[0] = (magnitude & 0x7f) |
+					      ((phase & 0x7f) << 7);
+
+			if ((im % 2) == 0)
+				REG_RMW_FIELD(ah, tx_corr_coeff[im][i],
+					AR_PHY_TX_IQCAL_CORR_COEFF_00_COEFF_TABLE,
+					coeff->iqc_coeff[0]);
+			else
+				REG_RMW_FIELD(ah, tx_corr_coeff[im][i],
+					AR_PHY_TX_IQCAL_CORR_COEFF_01_COEFF_TABLE,
+					coeff->iqc_coeff[0]);
+		}
+	}
+
+	REG_RMW_FIELD(ah, AR_PHY_TX_IQCAL_CONTROL_3,
+		      AR_PHY_TX_IQCAL_CONTROL_3_IQCORR_EN, 0x1);
+	REG_RMW_FIELD(ah, AR_PHY_RX_IQCAL_CORR_B0,
+		      AR_PHY_RX_IQCAL_CORR_B0_LOOPBACK_IQCORR_EN, 0x1);
+
+	return;
+
+disable_txiqcal:
+	REG_RMW_FIELD(ah, AR_PHY_TX_IQCAL_CONTROL_3,
+		      AR_PHY_TX_IQCAL_CONTROL_3_IQCORR_EN, 0x0);
+	REG_RMW_FIELD(ah, AR_PHY_RX_IQCAL_CORR_B0,
+		      AR_PHY_RX_IQCAL_CORR_B0_LOOPBACK_IQCORR_EN, 0x0);
+
+	ath_print(common, ATH_DBG_CALIBRATE, "TX IQ Cal disabled\n");
+}
+
+static void ar9003_hw_tx_iq_cal_run(struct ath_hw *ah)
+{
+	u8 tx_gain_forced;
+
+	REG_RMW_FIELD(ah, AR_PHY_TX_IQCAL_CONTROL_1_9485,
+		      AR_PHY_TX_IQCAQL_CONTROL_1_IQCORR_I_Q_COFF_DELPT, DELPT);
+	tx_gain_forced = REG_READ_FIELD(ah, AR_PHY_TX_FORCED_GAIN,
+					AR_PHY_TXGAIN_FORCE);
+	if (tx_gain_forced)
+		REG_RMW_FIELD(ah, AR_PHY_TX_FORCED_GAIN,
+			      AR_PHY_TXGAIN_FORCE, 0);
+
+	REG_RMW_FIELD(ah, AR_PHY_TX_IQCAL_START_9485,
+		      AR_PHY_TX_IQCAL_START_DO_CAL_9485, 1);
+}
+
+static void ar9003_hw_tx_iq_cal_post_proc(struct ath_hw *ah)
+{
+	struct ath_common *common = ath9k_hw_common(ah);
+	const u32 txiqcal_status[AR9300_MAX_CHAINS] = {
+		AR_PHY_TX_IQCAL_STATUS_B0_9485,
+		AR_PHY_TX_IQCAL_STATUS_B1,
+		AR_PHY_TX_IQCAL_STATUS_B2,
+	};
+	const u_int32_t chan_info_tab[] = {
+		AR_PHY_CHAN_INFO_TAB_0,
+		AR_PHY_CHAN_INFO_TAB_1,
+		AR_PHY_CHAN_INFO_TAB_2,
+	};
+	struct coeff coeff;
+	s32 iq_res[6];
+	u8 num_chains = 0;
+	int i, ip, im, j;
+	int nmeasurement;
+
+	for (i = 0; i < AR9300_MAX_CHAINS; i++) {
+		if (ah->txchainmask & (1 << i))
+			num_chains++;
+	}
+
+	for (ip = 0; ip < MPASS; ip++) {
+		for (i = 0; i < num_chains; i++) {
+			nmeasurement = REG_READ_FIELD(ah,
+					AR_PHY_TX_IQCAL_STATUS_B0_9485,
+					AR_PHY_CALIBRATED_GAINS_0);
+			if (nmeasurement > MAX_MEASUREMENT)
+				nmeasurement = MAX_MEASUREMENT;
+
+			for (im = 0; im < nmeasurement; im++) {
+				ath_print(common, ATH_DBG_CALIBRATE,
+					  "Doing Tx IQ Cal for chain %d.\n", i);
+
+				if (REG_READ(ah, txiqcal_status[i]) &
+				    AR_PHY_TX_IQCAL_STATUS_FAILED) {
+					ath_print(common, ATH_DBG_CALIBRATE,
+					"Tx IQ Cal failed for chain %d.\n", i);
+					goto tx_iqcal_fail;
+				}
+
+				for (j = 0; j < 3; j++) {
+					u32 idx = 2 * j, offset = 4 * (3 * im + j);
+
+					REG_RMW_FIELD(ah,
+						AR_PHY_CHAN_INFO_MEMORY,
+						AR_PHY_CHAN_INFO_TAB_S2_READ,
+						0);
+
+					/* 32 bits */
+					iq_res[idx] = REG_READ(ah,
+							chan_info_tab[i] +
+							offset);
+
+					REG_RMW_FIELD(ah,
+						AR_PHY_CHAN_INFO_MEMORY,
+						AR_PHY_CHAN_INFO_TAB_S2_READ,
+						1);
+
+					/* 16 bits */
+					iq_res[idx + 1] = 0xffff & REG_READ(ah,
+							  chan_info_tab[i] + offset);
+
+					ath_print(common, ATH_DBG_CALIBRATE,
+						  "IQ RES[%d]=0x%x"
+						  "IQ_RES[%d]=0x%x\n",
+						  idx, iq_res[idx], idx + 1,
+						  iq_res[idx + 1]);
+				}
+
+				if (!ar9003_hw_calc_iq_corr(ah, i, iq_res,
+							    coeff.iqc_coeff)) {
+					ath_print(common, ATH_DBG_CALIBRATE,
+					 "Failed in calculation of IQ correction.\n");
+					goto tx_iqcal_fail;
+				}
+
+				coeff.mag_coeff[i][im][ip] =
+						coeff.iqc_coeff[0] & 0x7f;
+				coeff.phs_coeff[i][im][ip] =
+						(coeff.iqc_coeff[0] >> 7) & 0x7f;
+
+				if (coeff.mag_coeff[i][im][ip] > 63)
+					coeff.mag_coeff[i][im][ip] -= 128;
+				if (coeff.phs_coeff[i][im][ip] > 63)
+					coeff.phs_coeff[i][im][ip] -= 128;
+			}
+		}
+	}
+	ar9003_hw_tx_iqcal_load_avg_2_passes(ah, num_chains, &coeff);
+
+	return;
+
+tx_iqcal_fail:
+	ath_print(common, ATH_DBG_CALIBRATE, "Tx IQ Cal failed\n");
+	return;
+}
 static bool ar9003_hw_init_cal(struct ath_hw *ah,
 			       struct ath9k_channel *chan)
 {
@@ -735,7 +968,11 @@ static bool ar9003_hw_init_cal(struct ath_hw *ah,
 		ar9003_hw_set_chain_masks(ah, 0x7, 0x7);
 
 	/* Do Tx IQ Calibration */
-	ar9003_hw_tx_iq_cal(ah);
+	if (AR_SREV_9485(ah))
+		ar9003_hw_tx_iq_cal_run(ah);
+	else
+		ar9003_hw_tx_iq_cal(ah);
+
 	REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_DIS);
 	udelay(5);
 	REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_EN);
@@ -754,6 +991,9 @@ static bool ar9003_hw_init_cal(struct ath_hw *ah,
 		return false;
 	}
 
+	if (AR_SREV_9485(ah))
+		ar9003_hw_tx_iq_cal_post_proc(ah);
+
 	/* Revert chainmasks to their original values before NF cal */
 	ar9003_hw_set_chain_masks(ah, ah->rxchainmask, ah->txchainmask);
 
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
index abb4ec1..74e0da9 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -546,6 +546,12 @@
 
 #define AR_PHY_TXGAIN_TABLE      (AR_SM_BASE + 0x300)
 
+#define AR_PHY_TX_IQCAL_START_9485		(AR_SM_BASE + 0x3c4)
+#define AR_PHY_TX_IQCAL_START_DO_CAL_9485	0x80000000
+#define AR_PHY_TX_IQCAL_START_DO_CAL_9485_S	31
+#define AR_PHY_TX_IQCAL_CONTROL_1_9485		(AR_SM_BASE + 0x3c8)
+#define AR_PHY_TX_IQCAL_STATUS_B0_9485		(AR_SM_BASE + 0x3f0)
+
 #define AR_PHY_TX_IQCAL_CONTROL_1   (AR_SM_BASE + 0x448)
 #define AR_PHY_TX_IQCAL_START       (AR_SM_BASE + 0x440)
 #define AR_PHY_TX_IQCAL_STATUS_B0   (AR_SM_BASE + 0x48c)
@@ -713,6 +719,7 @@
 #define AR_PHY_TPCGR1_FORCED_DAC_GAIN_S 1
 #define AR_PHY_TPCGR1_FORCE_DAC_GAIN    0x00000001
 #define AR_PHY_TXGAIN_FORCE               0x00000001
+#define AR_PHY_TXGAIN_FORCE_S		  0
 #define AR_PHY_TXGAIN_FORCED_PADVGNRA     0x00003c00
 #define AR_PHY_TXGAIN_FORCED_PADVGNRA_S   10
 #define AR_PHY_TXGAIN_FORCED_PADVGNRB     0x0003c000
@@ -755,8 +762,13 @@
 #define AR_PHY_TX_IQCAL_START_DO_CAL_S      0
 
 #define AR_PHY_TX_IQCAL_STATUS_FAILED    0x00000001
-#define AR_PHY_TX_IQCAL_CORR_COEFF_01_COEFF_TABLE      0x00003fff
-#define AR_PHY_TX_IQCAL_CORR_COEFF_01_COEFF_TABLE_S    0
+#define AR_PHY_CALIBRATED_GAINS_0	 0x3e
+#define AR_PHY_CALIBRATED_GAINS_0_S	 1
+
+#define AR_PHY_TX_IQCAL_CORR_COEFF_00_COEFF_TABLE      0x00003fff
+#define AR_PHY_TX_IQCAL_CORR_COEFF_00_COEFF_TABLE_S    0
+#define AR_PHY_TX_IQCAL_CORR_COEFF_01_COEFF_TABLE      0x0fffc000
+#define AR_PHY_TX_IQCAL_CORR_COEFF_01_COEFF_TABLE_S    14
 
 #define AR_PHY_65NM_CH0_RXTX4_THERM_ON          0x10000000
 #define AR_PHY_65NM_CH0_RXTX4_THERM_ON_S        28
-- 
1.7.0.4

[PATCH 23/26] ath9k_hw: Program appropriate register for temperature compensation cal for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_phy.h |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
index 74e0da9..00cd3e5 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -586,7 +586,7 @@
 #define AR_PHY_65NM_CH0_BIAS2       0x160c4
 #define AR_PHY_65NM_CH0_BIAS4       0x160cc
 #define AR_PHY_65NM_CH0_RXTX4       0x1610c
-#define AR_PHY_65NM_CH0_THERM       0x16290
+#define AR_PHY_65NM_CH0_THERM       (AR_SREV_9485(ah) ? 0x1628c : 0x16290)
 
 #define AR_PHY_65NM_CH0_THERM_LOCAL   0x80000000
 #define AR_PHY_65NM_CH0_THERM_LOCAL_S 31
-- 
1.7.0.4

[PATCH 24/26] ath9k_hw: Setup paprd only for chain 0 on AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_paprd.c |   40 +++++++++++++++++--------
 drivers/net/wireless/ath/ath9k/ar9003_phy.h   |   16 +++++++--
 2 files changed, 39 insertions(+), 17 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_paprd.c b/drivers/net/wireless/ath/ath9k/ar9003_paprd.c
index 850bc98..71d7648 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_paprd.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_paprd.c
@@ -21,10 +21,12 @@ void ar9003_paprd_enable(struct ath_hw *ah, bool val)
 {
 	REG_RMW_FIELD(ah, AR_PHY_PAPRD_CTRL0_B0,
 		      AR_PHY_PAPRD_CTRL0_PAPRD_ENABLE, !!val);
-	REG_RMW_FIELD(ah, AR_PHY_PAPRD_CTRL0_B1,
-		      AR_PHY_PAPRD_CTRL0_PAPRD_ENABLE, !!val);
-	REG_RMW_FIELD(ah, AR_PHY_PAPRD_CTRL0_B2,
-		      AR_PHY_PAPRD_CTRL0_PAPRD_ENABLE, !!val);
+	if (!AR_SREV_9485(ah)) {
+		REG_RMW_FIELD(ah, AR_PHY_PAPRD_CTRL0_B1,
+			      AR_PHY_PAPRD_CTRL0_PAPRD_ENABLE, !!val);
+		REG_RMW_FIELD(ah, AR_PHY_PAPRD_CTRL0_B2,
+			      AR_PHY_PAPRD_CTRL0_PAPRD_ENABLE, !!val);
+	}
 }
 EXPORT_SYMBOL(ar9003_paprd_enable);
 
@@ -44,6 +46,7 @@ static void ar9003_paprd_setup_single_table(struct ath_hw *ah)
 	};
 	u32 am_mask, ht40_mask;
 	int i;
+	u8 nchains = AR9300_MAX_CHAINS;
 
 	if (ah->curchan && IS_CHAN_5GHZ(ah->curchan))
 		hdr = &eep->modalHeader5G;
@@ -57,7 +60,10 @@ static void ar9003_paprd_setup_single_table(struct ath_hw *ah)
 	REG_RMW_FIELD(ah, AR_PHY_PAPRD_AM2PM, AR_PHY_PAPRD_AM2PM_MASK, am_mask);
 	REG_RMW_FIELD(ah, AR_PHY_PAPRD_HT40, AR_PHY_PAPRD_HT40_MASK, ht40_mask);
 
-	for (i = 0; i < 3; i++) {
+	if (AR_SREV_9485(ah))
+		nchains = 1;
+
+	for (i = 0; i < nchains; i++) {
 		REG_RMW_FIELD(ah, ctrl0[i],
 			      AR_PHY_PAPRD_CTRL0_USE_SINGLE_TABLE_MASK, 1);
 		REG_RMW_FIELD(ah, ctrl1[i],
@@ -102,8 +108,14 @@ static void ar9003_paprd_setup_single_table(struct ath_hw *ah)
 		      AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_NUM_CORR_STAGES, 7);
 	REG_RMW_FIELD(ah, AR_PHY_PAPRD_TRAINER_CNTL3,
 		      AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_MIN_LOOPBACK_DEL, 1);
-	REG_RMW_FIELD(ah, AR_PHY_PAPRD_TRAINER_CNTL3,
-		      AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_QUICK_DROP, -6);
+	if (AR_SREV_9485(ah))
+		REG_RMW_FIELD(ah, AR_PHY_PAPRD_TRAINER_CNTL3,
+			      AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_QUICK_DROP,
+			      -3);
+	else
+		REG_RMW_FIELD(ah, AR_PHY_PAPRD_TRAINER_CNTL3,
+			      AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_QUICK_DROP,
+			      -6);
 	REG_RMW_FIELD(ah, AR_PHY_PAPRD_TRAINER_CNTL3,
 		      AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_ADC_DESIRED_SIZE,
 		      -15);
@@ -620,13 +632,15 @@ void ar9003_paprd_populate_single_table(struct ath_hw *ah,
 		      AR_PHY_PAPRD_CTRL1_PAPRD_POWER_AT_AM2AM_CAL,
 		      training_power);
 
-	REG_RMW_FIELD(ah, AR_PHY_PAPRD_CTRL1_B1,
-		      AR_PHY_PAPRD_CTRL1_PAPRD_POWER_AT_AM2AM_CAL,
-		      training_power);
+	if (!AR_SREV_9485(ah)) {
+		REG_RMW_FIELD(ah, AR_PHY_PAPRD_CTRL1_B1,
+			      AR_PHY_PAPRD_CTRL1_PAPRD_POWER_AT_AM2AM_CAL,
+			      training_power);
 
-	REG_RMW_FIELD(ah, AR_PHY_PAPRD_CTRL1_B2,
-		      AR_PHY_PAPRD_CTRL1_PAPRD_POWER_AT_AM2AM_CAL,
-		      training_power);
+		REG_RMW_FIELD(ah, AR_PHY_PAPRD_CTRL1_B2,
+			      AR_PHY_PAPRD_CTRL1_PAPRD_POWER_AT_AM2AM_CAL,
+			      training_power);
+	}
 }
 EXPORT_SYMBOL(ar9003_paprd_populate_single_table);
 
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
index 00cd3e5..6f811c7 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -987,7 +987,9 @@
 #define AR_PHY_PAPRD_CTRL1_PAPRD_MAG_SCALE_FACT		0x0ffe0000
 #define AR_PHY_PAPRD_CTRL1_PAPRD_MAG_SCALE_FACT_S	17
 
-#define AR_PHY_PAPRD_TRAINER_CNTL1				(AR_SM_BASE + 0x490)
+#define AR_PHY_PAPRD_TRAINER_CNTL1				(AR_SM_BASE + \
+								 (AR_SREV_9485(ah) ? \
+								  0x580 : 0x490))
 #define AR_PHY_PAPRD_TRAINER_CNTL1_CF_CF_PAPRD_TRAIN_ENABLE	0x00000001
 #define AR_PHY_PAPRD_TRAINER_CNTL1_CF_CF_PAPRD_TRAIN_ENABLE_S	0
 #define AR_PHY_PAPRD_TRAINER_CNTL1_CF_PAPRD_AGC2_SETTLING	0x0000007e
@@ -1003,11 +1005,15 @@
 #define AR_PHY_PAPRD_TRAINER_CNTL1_CF_PAPRD_LB_SKIP		0x0003f000
 #define AR_PHY_PAPRD_TRAINER_CNTL1_CF_PAPRD_LB_SKIP_S		12
 
-#define AR_PHY_PAPRD_TRAINER_CNTL2				(AR_SM_BASE + 0x494)
+#define AR_PHY_PAPRD_TRAINER_CNTL2				(AR_SM_BASE + \
+								 (AR_SREV_9485(ah) ? \
+								  0x584 : 0x494))
 #define AR_PHY_PAPRD_TRAINER_CNTL2_CF_PAPRD_INIT_RX_BB_GAIN	0xFFFFFFFF
 #define AR_PHY_PAPRD_TRAINER_CNTL2_CF_PAPRD_INIT_RX_BB_GAIN_S	0
 
-#define AR_PHY_PAPRD_TRAINER_CNTL3				(AR_SM_BASE + 0x498)
+#define AR_PHY_PAPRD_TRAINER_CNTL3				(AR_SM_BASE + \
+								 (AR_SREV_9485(ah) ? \
+								  0x588 : 0x498))
 #define AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_ADC_DESIRED_SIZE	0x0000003f
 #define AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_ADC_DESIRED_SIZE_S	0
 #define AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_QUICK_DROP		0x00000fc0
@@ -1023,7 +1029,9 @@
 #define AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_BBTXMIX_DISABLE	0x20000000
 #define AR_PHY_PAPRD_TRAINER_CNTL3_CF_PAPRD_BBTXMIX_DISABLE_S	29
 
-#define AR_PHY_PAPRD_TRAINER_CNTL4				(AR_SM_BASE + 0x49c)
+#define AR_PHY_PAPRD_TRAINER_CNTL4				(AR_SM_BASE + \
+								 (AR_SREV_9485(ah) ? \
+								  0x58c : 0x49c))
 #define AR_PHY_PAPRD_TRAINER_CNTL4_CF_PAPRD_NUM_TRAIN_SAMPLES	0x03ff0000
 #define AR_PHY_PAPRD_TRAINER_CNTL4_CF_PAPRD_NUM_TRAIN_SAMPLES_S	16
 #define AR_PHY_PAPRD_TRAINER_CNTL4_CF_PAPRD_SAFETY_DELTA	0x0000f000
-- 
1.7.0.4

Re: [PATCH 24/26] ath9k_hw: Setup paprd only for chain 0 on AR9485

[Felix Fietkau]

On 2010-12-01 8:32 AM, Vasanthakumar Thiagarajan wrote:
> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Same here as with the other two chain register related patches.

- Felix

[PATCH 25/26] ath9k_hw: Disable MRC CCK for AR9485

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/ani.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ani.c b/drivers/net/wireless/ath/ath9k/ani.c
index 29a045d..990da39 100644
--- a/drivers/net/wireless/ath/ath9k/ani.c
+++ b/drivers/net/wireless/ath/ath9k/ani.c
@@ -358,7 +358,7 @@ static void ath9k_hw_set_cck_nil(struct ath_hw *ah, u_int8_t immunityLevel)
 				     entry_cck->fir_step_level);
 
 	/* Skip MRC CCK for pre AR9003 families */
-	if (!AR_SREV_9300_20_OR_LATER(ah))
+	if (!AR_SREV_9300_20_OR_LATER(ah) || AR_SREV_9485(ah))
 		return;
 
 	if (aniState->mrcCCKOff == entry_cck->mrc_cck_on)
-- 
1.7.0.4

[PATCH 26/26] ath9k: Add device id of AR9485 to pci table

[Vasanthakumar Thiagarajan]

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
---
 drivers/net/wireless/ath/ath9k/pci.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/pci.c b/drivers/net/wireless/ath/ath9k/pci.c
index c5a523d..842c38d 100644
--- a/drivers/net/wireless/ath/ath9k/pci.c
+++ b/drivers/net/wireless/ath/ath9k/pci.c
@@ -30,6 +30,7 @@ static DEFINE_PCI_DEVICE_TABLE(ath_pci_id_table) = {
 	{ PCI_VDEVICE(ATHEROS, 0x002D) }, /* PCI   */
 	{ PCI_VDEVICE(ATHEROS, 0x002E) }, /* PCI-E */
 	{ PCI_VDEVICE(ATHEROS, 0x0030) }, /* PCI-E  AR9300 */
+	{ PCI_VDEVICE(ATHEROS, 0x0032) }, /* PCI-E  AR9485 */
 	{ 0 }
 };
 
-- 
1.7.0.4

Re: [PATCH 00/26] Add support for AR9485

[Luis R. Rodriguez]

On Tue, Nov 30, 2010 at 11:32 PM, Vasanthakumar Thiagarajan
<vasanth@atheros.com> wrote:
> John,
>
>        This patch series add support for a new chipset of AR9003 family.
> This chip(AR9485) is an 1x1 and 2.4Ghz band only.

Very nice Vasanth, good stuff! If these are all checkpatch.pl and sparse tested:

Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>

  Luis

Re: [PATCH 00/26] Add support for AR9485

[Vasanthakumar Thiagarajan]

On Wed, Dec 01, 2010 at 01:22:12PM +0530, Luis R. Rodriguez wrote:
> On Tue, Nov 30, 2010 at 11:32 PM, Vasanthakumar Thiagarajan
> <vasanth@atheros.com> wrote:
> > John,
> >
> >        This patch series add support for a new chipset of AR9003 family.
> > This chip(AR9485) is an 1x1 and 2.4Ghz band only.
> 
> Very nice Vasanth, good stuff! If these are all checkpatch.pl and sparse tested:

Yes, sparse and checkpatch.pl tested, got some checkpatch.pl
warnings for being over 80 char, but that should be fine.
Thanks for the review.

Vasanth