* [ath5k] kernel panic while using compat-wireless-2.6.38.2-2
@ 2011-05-11 10:38 Dennis Borgmann
2011-05-23 16:21 ` Dennis Borgmann
0 siblings, 1 reply; 6+ messages in thread
From: Dennis Borgmann @ 2011-05-11 10:38 UTC (permalink / raw)
To: linux-wireless
Hello linux-wireless list!
I am using a Sparklan WPEA-166G/W with Chipset AR5BXB63 Rev. 11 (it's a
MiniPCI-card) in an embedded X86-System (Pipal 2140U, Intel ATOM
processor). It's running voyage-0.6.5, which essentially is a Debian
Lenny System.
I am running kernel 2.6.33.9-rt31:
demo00000001:~# uname -a
Linux SSB_wlan-demo00000001 2.6.33.9-rt31-atom-ssb #1 PREEMPT RT Mon May
9 18:25:28 CEST 2011 i686 GNU/Linux
I installed the compat-wireless drivers version 2.6.38.2-2 (
http://www.orbit-lab.org/kernel/compat-wireless-2.6-stable/v2.6.38/compat-wireless-2.6.38.2-2.tar.bz2
) and installed everything I need according to this webpage:
http://acx100.erley.org/stable.html
Once issueing modprobe ath5k, putting the interface up and waiting for
~30sec, I get a kernel panic. Could this be a bug or am I doing
something wrong?
The error only occurrs after putting the interface up. If I don't do so,
the error won't be there.
Here is some output from the machine:
demo00000001:~# modprobe ath5k && ifconfig wlan0 up
[ 48.363894] Compat-wireless backport release: compat-wireless-2.6.38.2-2
[ 48.372351] Backport based on linux-2.6-allstable.git v2.6.38.2
[ 48.411748] cfg80211: Calling CRDA to update world regulatory domain
[ 48.517969] ath5k 0000:09:00.0: using bridge 0000:00:1c.2 INT A to
get IRQ 17
[ 48.526919] ath5k 0000:09:00.0: PCI->APIC IRQ transform: INT A -> IRQ 17
[ 48.534315] ath5k 0000:09:00.0: registered as 'phy0'
[ 49.162919] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
demo00000001:~# [ 77.953752] ------------[ cut here ]------------
[ 77.958711] WARNING: at
/home/dborgmann/downloads/compat-wireless-2.6.38.2-2/net/mac80211/rx.c:2827
ieee80211_rx+0x38/0x6fe [mac80211]()
[ 77.971856] Hardware name: Luna Pier CRB
[ 77.976049] Modules linked in: [last unloaded: scsi_wait_scan]
[ 77.982354] Pid: 9, comm: sirq-tasklet/0 Not tainted
2.6.33.9-rt31-atom-ssb #1
[ 77.990090] Call Trace:
[ 77.992732] [<c011852f>] warn_slowpath_common+0x65/0x7c
[ 77.998419] [<e0024ad1>] ? ieee80211_rx+0x38/0x6fe [mac80211]
[ 78.004672] [<c0118553>] warn_slowpath_null+0xd/0x10
[ 78.010119] [<e0024ad1>] ieee80211_rx+0x38/0x6fe [mac80211]
[ 78.016157] [<c022d6e8>] ? __alloc_skb+0x4c/0x110
[ 78.021296] [<c0106297>] ? nommu_map_page+0x3c/0x51
[ 78.026648] [<e00992c9>] ? ath5k_rx_skb_alloc+0x99/0x10a [ath5k]
[ 78.033190] [<e009b989>] ath5k_tasklet_rx+0x59f/0x60b [ath5k]
[ 78.039454] [<c011c486>] __tasklet_action.clone.8+0x76/0xd1
[ 78.045502] [<c011c529>] tasklet_action+0x23/0x25
[ 78.050640] [<c011c285>] run_ksoftirqd+0xf0/0x19b
[ 78.055788] [<c011c195>] ? run_ksoftirqd+0x0/0x19b
[ 78.061032] [<c0127829>] kthread+0x5e/0x63
[ 78.065538] [<c01277cb>] ? kthread+0x0/0x63
[ 78.070107] [<c0102bb6>] kernel_thread_helper+0x6/0x10
[ 78.075695] ---[ end trace 6b864a3c0aa1a8eb ]---
Best regards,
Dennis
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2
2011-05-11 10:38 [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 Dennis Borgmann
@ 2011-05-23 16:21 ` Dennis Borgmann
2011-05-23 16:35 ` Ben Greear
0 siblings, 1 reply; 6+ messages in thread
From: Dennis Borgmann @ 2011-05-23 16:21 UTC (permalink / raw)
To: linux-wireless
Hello linux-wireless list!
Is there really no one with an idea? Is there no one among the
developers, who is interested in this bug, if it is a bug?
I'm starting to lose my hope...
Dennis
Am 11.05.2011 12:38, schrieb Dennis Borgmann:
> Hello linux-wireless list!
>
> I am using a Sparklan WPEA-166G/W with Chipset AR5BXB63 Rev. 11 (it's
> a MiniPCI-card) in an embedded X86-System (Pipal 2140U, Intel ATOM
> processor). It's running voyage-0.6.5, which essentially is a Debian
> Lenny System.
>
> I am running kernel 2.6.33.9-rt31:
>
> demo00000001:~# uname -a
> Linux SSB_wlan-demo00000001 2.6.33.9-rt31-atom-ssb #1 PREEMPT RT Mon
> May 9 18:25:28 CEST 2011 i686 GNU/Linux
>
> I installed the compat-wireless drivers version 2.6.38.2-2 (
> http://www.orbit-lab.org/kernel/compat-wireless-2.6-stable/v2.6.38/compat-wireless-2.6.38.2-2.tar.bz2
> ) and installed everything I need according to this webpage:
> http://acx100.erley.org/stable.html
>
> Once issueing modprobe ath5k, putting the interface up and waiting for
> ~30sec, I get a kernel panic. Could this be a bug or am I doing
> something wrong?
>
> The error only occurrs after putting the interface up. If I don't do
> so, the error won't be there.
>
> Here is some output from the machine:
>
> demo00000001:~# modprobe ath5k && ifconfig wlan0 up
> [ 48.363894] Compat-wireless backport release:
> compat-wireless-2.6.38.2-2
> [ 48.372351] Backport based on linux-2.6-allstable.git v2.6.38.2
> [ 48.411748] cfg80211: Calling CRDA to update world regulatory domain
> [ 48.517969] ath5k 0000:09:00.0: using bridge 0000:00:1c.2 INT A to
> get IRQ 17
> [ 48.526919] ath5k 0000:09:00.0: PCI->APIC IRQ transform: INT A ->
> IRQ 17
> [ 48.534315] ath5k 0000:09:00.0: registered as 'phy0'
> [ 49.162919] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY:
> 0x70)
> demo00000001:~# [ 77.953752] ------------[ cut here ]------------
> [ 77.958711] WARNING: at
> /home/dborgmann/downloads/compat-wireless-2.6.38.2-2/net/mac80211/rx.c:2827
> ieee80211_rx+0x38/0x6fe [mac80211]()
> [ 77.971856] Hardware name: Luna Pier CRB
> [ 77.976049] Modules linked in: [last unloaded: scsi_wait_scan]
> [ 77.982354] Pid: 9, comm: sirq-tasklet/0 Not tainted
> 2.6.33.9-rt31-atom-ssb #1
> [ 77.990090] Call Trace:
> [ 77.992732] [<c011852f>] warn_slowpath_common+0x65/0x7c
> [ 77.998419] [<e0024ad1>] ? ieee80211_rx+0x38/0x6fe [mac80211]
> [ 78.004672] [<c0118553>] warn_slowpath_null+0xd/0x10
> [ 78.010119] [<e0024ad1>] ieee80211_rx+0x38/0x6fe [mac80211]
> [ 78.016157] [<c022d6e8>] ? __alloc_skb+0x4c/0x110
> [ 78.021296] [<c0106297>] ? nommu_map_page+0x3c/0x51
> [ 78.026648] [<e00992c9>] ? ath5k_rx_skb_alloc+0x99/0x10a [ath5k]
> [ 78.033190] [<e009b989>] ath5k_tasklet_rx+0x59f/0x60b [ath5k]
> [ 78.039454] [<c011c486>] __tasklet_action.clone.8+0x76/0xd1
> [ 78.045502] [<c011c529>] tasklet_action+0x23/0x25
> [ 78.050640] [<c011c285>] run_ksoftirqd+0xf0/0x19b
> [ 78.055788] [<c011c195>] ? run_ksoftirqd+0x0/0x19b
> [ 78.061032] [<c0127829>] kthread+0x5e/0x63
> [ 78.065538] [<c01277cb>] ? kthread+0x0/0x63
> [ 78.070107] [<c0102bb6>] kernel_thread_helper+0x6/0x10
> [ 78.075695] ---[ end trace 6b864a3c0aa1a8eb ]---
>
>
> Best regards,
> Dennis
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2
2011-05-23 16:21 ` Dennis Borgmann
@ 2011-05-23 16:35 ` Ben Greear
2011-05-24 19:11 ` Dennis Borgmann
2011-05-24 20:03 ` Dennis Borgmann
0 siblings, 2 replies; 6+ messages in thread
From: Ben Greear @ 2011-05-23 16:35 UTC (permalink / raw)
To: Dennis Borgmann; +Cc: linux-wireless
On 05/23/2011 09:21 AM, Dennis Borgmann wrote:
> Hello linux-wireless list!
>
> Is there really no one with an idea? Is there no one among the
> developers, who is interested in this bug, if it is a bug?
>
> I'm starting to lose my hope...
Can you reproduce this in the wireless-testing tree?
Ben
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2
2011-05-23 16:35 ` Ben Greear
@ 2011-05-24 19:11 ` Dennis Borgmann
2011-05-24 20:03 ` Dennis Borgmann
1 sibling, 0 replies; 6+ messages in thread
From: Dennis Borgmann @ 2011-05-24 19:11 UTC (permalink / raw)
To: Ben Greear; +Cc: linux-wireless
Problem has been solved by using latest compat-wireless-2.6.39-1 from
last night.
Finally.
Thank you, linux-wireless folks!
Best regards,
Dennis
Am 23.05.2011 18:35, schrieb Ben Greear:
> On 05/23/2011 09:21 AM, Dennis Borgmann wrote:
>> Hello linux-wireless list!
>>
>> Is there really no one with an idea? Is there no one among the
>> developers, who is interested in this bug, if it is a bug?
>>
>> I'm starting to lose my hope...
>
> Can you reproduce this in the wireless-testing tree?
>
> Ben
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2
2011-05-23 16:35 ` Ben Greear
2011-05-24 19:11 ` Dennis Borgmann
@ 2011-05-24 20:03 ` Dennis Borgmann
2011-05-24 20:47 ` Ben Greear
1 sibling, 1 reply; 6+ messages in thread
From: Dennis Borgmann @ 2011-05-24 20:03 UTC (permalink / raw)
To: Ben Greear; +Cc: linux-wireless
Dear linux-wireless list,
sorry, I did answer too early, problem still exists. I am now using
compat-wireless-2.6.39-1. I hope, this is new enough (it seems to be
from last night anyway...)
I now even exchanged the wireless card, now I am using a Gigabyte
GN-WI01HT (AR5414 chip), the problem seems to be the same. I attached
some dmesg info. Could this be a hardware error of the mainboard?
Actually, I only have one hardware to test on and I somehow don't really
trust it. Just a thought of mine...
What are your suggestions, or could this really be a bug?
Best regards,
Dennis
[ 7.525432] Compat-wireless backport release: compat-wireless-v2.6.39-1
[ 7.532737] Backport based on linux-2.6-allstable.git v2.6.39
[ 7.576502] cfg80211: Calling CRDA to update world regulatory domain
[ 7.640147] cfg80211: World regulatory domain updated:
[ 7.645908] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 7.656157] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 7.664483] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz),
(300 mBi, 2000 mBm)
[ 7.672754] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz),
(300 mBi, 2000 mBm)
[ 7.674546] ath5k 0000:11:07.0: PCI->APIC IRQ transform: INT A -> IRQ 19
[ 7.688710] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 7.697046] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 7.705453] ath5k 0000:11:07.0: registered as 'phy0'
[ 8.351679] ath: EEPROM regdomain: 0x0
[ 8.351685] ath: EEPROM indicates default country code should be used
[ 8.351690] ath: doing EEPROM country->regdmn map search
[ 8.351695] ath: country maps to regdmn code: 0x3a
[ 8.351699] ath: Country alpha2 being used: US
[ 8.351703] ath: Regpair used: 0x3a
[ 8.360800] ieee80211 phy0: Selected rate control algorithm
'minstrel_ht'
[ 8.362487] cfg80211: Calling CRDA for country: US
[ 8.362536] ath5k phy0: Atheros AR5414 chip found (MAC: 0xa5, PHY: 0x61)
[ 8.363657] modprobe used greatest stack depth: 5860 bytes left
[ 8.388493] cfg80211: Regulatory domain changed to country: US
[ 8.394937] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 8.403724] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(300 mBi, 2700 mBm)
[ 8.412246] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz),
(300 mBi, 1700 mBm)
[ 8.421561] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 8.430451] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 8.438853] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz),
(300 mBi, 2000 mBm)
[ 8.447623] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz),
(300 mBi, 3000 mBm)
[ 8.496322] scsi 4:0:0:0: Direct-Access Generic Storage Device
0.00 PQ: 0 ANSI: 2
[ 8.505354] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 8.511989] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 8.796704] chown used greatest stack depth: 5824 bytes left
[ 27.909475] cfg80211: Calling CRDA for country: DE
[ 27.920079] cfg80211: Regulatory domain changed to country: DE
[ 27.927544] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 27.937610] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 27.945562] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 27.953475] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 27.961475] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz),
(N/A, 2698 mBm)
[ 28.014622] hostapd used greatest stack depth: 5748 bytes left
[ 33.195098] ------------[ cut here ]------------
[ 33.201175] WARNING: at
/mnt/entw/compat-wireless-2.6.39-1/net/mac80211/rx.c:2882
ieee80211_rx+0x39/0x660 [mac80211]()
[ 33.213802] Hardware name: Luna Pier CRB
[ 33.219331] Modules linked in: ath5k ath mac80211 cfg80211 compat
[last unloaded: scsi_wait_scan]
[ 33.226899] Pid: 24, comm: sirq-tasklet/1 Not tainted
2.6.33.7.2-rt30-atom-ssb #1
[ 33.236137] Call Trace:
[ 33.240118] [<c1030666>] warn_slowpath_common+0x60/0x90
[ 33.247071] [<c10306a3>] warn_slowpath_null+0xd/0x10
[ 33.253762] [<dff60edd>] ieee80211_rx+0x39/0x660 [mac80211]
[ 33.261111] [<e031064c>] ath5k_tasklet_rx+0x540/0x5aa [ath5k]
[ 33.268566] [<c102b281>] ? set_next_entity+0x1e/0x89
[ 33.273935] [<c135941d>] ? __schedule+0x76f/0x7a4
[ 33.280319] [<c10356b4>] __tasklet_action+0x77/0xd7
[ 33.285564] [<c10357d2>] tasklet_action+0x5c/0x62
[ 33.291956] [<c1035c19>] run_ksoftirqd+0x131/0x247
[ 33.297091] [<c1035ae8>] ? run_ksoftirqd+0x0/0x247
[ 33.303589] [<c1046ab6>] kthread+0x61/0x66
[ 33.308029] [<c1046a55>] ? kthread+0x0/0x66
[ 33.313884] [<c1002db6>] kernel_thread_helper+0x6/0x10
[ 33.319430] ---[ end trace 95aeede189daca6f ]---
Am 23.05.2011 18:35, schrieb Ben Greear:
> On 05/23/2011 09:21 AM, Dennis Borgmann wrote:
>> Hello linux-wireless list!
>>
>> Is there really no one with an idea? Is there no one among the
>> developers, who is interested in this bug, if it is a bug?
>>
>> I'm starting to lose my hope...
>
> Can you reproduce this in the wireless-testing tree?
>
> Ben
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2
2011-05-24 20:03 ` Dennis Borgmann
@ 2011-05-24 20:47 ` Ben Greear
0 siblings, 0 replies; 6+ messages in thread
From: Ben Greear @ 2011-05-24 20:47 UTC (permalink / raw)
To: Dennis Borgmann; +Cc: linux-wireless
On 05/24/2011 01:03 PM, Dennis Borgmann wrote:
> Dear linux-wireless list,
>
> sorry, I did answer too early, problem still exists. I am now using
> compat-wireless-2.6.39-1. I hope, this is new enough (it seems to be
> from last night anyway...)
>
> I now even exchanged the wireless card, now I am using a Gigabyte
> GN-WI01HT (AR5414 chip), the problem seems to be the same. I attached
> some dmesg info. Could this be a hardware error of the mainboard?
> Actually, I only have one hardware to test on and I somehow don't really
> trust it. Just a thought of mine...
>
> What are your suggestions, or could this really be a bug?
I use the wireless-testing tree, not any compat stuff. We are
testing ath5k and ath9k currently, and no troubles.
If you can reproduce it using wireless-testing, I'll look
at it closer. Otherwise, it might be some problem with
the backport.
Thanks,
Ben
>
> Best regards,
> Dennis
>
>
> [ 7.525432] Compat-wireless backport release: compat-wireless-v2.6.39-1
> [ 7.532737] Backport based on linux-2.6-allstable.git v2.6.39
> [ 7.576502] cfg80211: Calling CRDA to update world regulatory domain
> [ 7.640147] cfg80211: World regulatory domain updated:
> [ 7.645908] cfg80211: (start_freq - end_freq @ bandwidth),
> (max_antenna_gain, max_eirp)
> [ 7.656157] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
> 2000 mBm)
> [ 7.664483] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
> 2000 mBm)
> [ 7.672754] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
> 2000 mBm)
> [ 7.674546] ath5k 0000:11:07.0: PCI->APIC IRQ transform: INT A -> IRQ 19
> [ 7.688710] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
> 2000 mBm)
> [ 7.697046] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
> 2000 mBm)
> [ 7.705453] ath5k 0000:11:07.0: registered as 'phy0'
> [ 8.351679] ath: EEPROM regdomain: 0x0
> [ 8.351685] ath: EEPROM indicates default country code should be used
> [ 8.351690] ath: doing EEPROM country->regdmn map search
> [ 8.351695] ath: country maps to regdmn code: 0x3a
> [ 8.351699] ath: Country alpha2 being used: US
> [ 8.351703] ath: Regpair used: 0x3a
> [ 8.360800] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
> [ 8.362487] cfg80211: Calling CRDA for country: US
> [ 8.362536] ath5k phy0: Atheros AR5414 chip found (MAC: 0xa5, PHY: 0x61)
> [ 8.363657] modprobe used greatest stack depth: 5860 bytes left
> [ 8.388493] cfg80211: Regulatory domain changed to country: US
> [ 8.394937] cfg80211: (start_freq - end_freq @ bandwidth),
> (max_antenna_gain, max_eirp)
> [ 8.403724] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
> 2700 mBm)
> [ 8.412246] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
> 1700 mBm)
> [ 8.421561] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi,
> 2000 mBm)
> [ 8.430451] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi,
> 2000 mBm)
> [ 8.438853] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi,
> 2000 mBm)
> [ 8.447623] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
> 3000 mBm)
> [ 8.496322] scsi 4:0:0:0: Direct-Access Generic Storage Device 0.00 PQ:
> 0 ANSI: 2
> [ 8.505354] sd 4:0:0:0: Attached scsi generic sg1 type 0
> [ 8.511989] sd 4:0:0:0: [sdb] Attached SCSI removable disk
> [ 8.796704] chown used greatest stack depth: 5824 bytes left
> [ 27.909475] cfg80211: Calling CRDA for country: DE
> [ 27.920079] cfg80211: Regulatory domain changed to country: DE
> [ 27.927544] cfg80211: (start_freq - end_freq @ bandwidth),
> (max_antenna_gain, max_eirp)
> [ 27.937610] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A,
> 2000 mBm)
> [ 27.945562] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A,
> 2000 mBm)
> [ 27.953475] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A,
> 2000 mBm)
> [ 27.961475] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A,
> 2698 mBm)
> [ 28.014622] hostapd used greatest stack depth: 5748 bytes left
> [ 33.195098] ------------[ cut here ]------------
> [ 33.201175] WARNING: at
> /mnt/entw/compat-wireless-2.6.39-1/net/mac80211/rx.c:2882
> ieee80211_rx+0x39/0x660 [mac80211]()
> [ 33.213802] Hardware name: Luna Pier CRB
> [ 33.219331] Modules linked in: ath5k ath mac80211 cfg80211 compat [last
> unloaded: scsi_wait_scan]
> [ 33.226899] Pid: 24, comm: sirq-tasklet/1 Not tainted
> 2.6.33.7.2-rt30-atom-ssb #1
> [ 33.236137] Call Trace:
> [ 33.240118] [<c1030666>] warn_slowpath_common+0x60/0x90
> [ 33.247071] [<c10306a3>] warn_slowpath_null+0xd/0x10
> [ 33.253762] [<dff60edd>] ieee80211_rx+0x39/0x660 [mac80211]
> [ 33.261111] [<e031064c>] ath5k_tasklet_rx+0x540/0x5aa [ath5k]
> [ 33.268566] [<c102b281>] ? set_next_entity+0x1e/0x89
> [ 33.273935] [<c135941d>] ? __schedule+0x76f/0x7a4
> [ 33.280319] [<c10356b4>] __tasklet_action+0x77/0xd7
> [ 33.285564] [<c10357d2>] tasklet_action+0x5c/0x62
> [ 33.291956] [<c1035c19>] run_ksoftirqd+0x131/0x247
> [ 33.297091] [<c1035ae8>] ? run_ksoftirqd+0x0/0x247
> [ 33.303589] [<c1046ab6>] kthread+0x61/0x66
> [ 33.308029] [<c1046a55>] ? kthread+0x0/0x66
> [ 33.313884] [<c1002db6>] kernel_thread_helper+0x6/0x10
> [ 33.319430] ---[ end trace 95aeede189daca6f ]---
>
>
> Am 23.05.2011 18:35, schrieb Ben Greear:
>> On 05/23/2011 09:21 AM, Dennis Borgmann wrote:
>>> Hello linux-wireless list!
>>>
>>> Is there really no one with an idea? Is there no one among the
>>> developers, who is interested in this bug, if it is a bug?
>>>
>>> I'm starting to lose my hope...
>>
>> Can you reproduce this in the wireless-testing tree?
>>
>> Ben
>>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2011-05-24 20:47 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-05-11 10:38 [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 Dennis Borgmann
2011-05-23 16:21 ` Dennis Borgmann
2011-05-23 16:35 ` Ben Greear
2011-05-24 19:11 ` Dennis Borgmann
2011-05-24 20:03 ` Dennis Borgmann
2011-05-24 20:47 ` Ben Greear
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).