* [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 @ 2011-05-11 10:38 Dennis Borgmann 2011-05-23 16:21 ` Dennis Borgmann 0 siblings, 1 reply; 6+ messages in thread From: Dennis Borgmann @ 2011-05-11 10:38 UTC (permalink / raw) To: linux-wireless Hello linux-wireless list! I am using a Sparklan WPEA-166G/W with Chipset AR5BXB63 Rev. 11 (it's a MiniPCI-card) in an embedded X86-System (Pipal 2140U, Intel ATOM processor). It's running voyage-0.6.5, which essentially is a Debian Lenny System. I am running kernel 2.6.33.9-rt31: demo00000001:~# uname -a Linux SSB_wlan-demo00000001 2.6.33.9-rt31-atom-ssb #1 PREEMPT RT Mon May 9 18:25:28 CEST 2011 i686 GNU/Linux I installed the compat-wireless drivers version 2.6.38.2-2 ( http://www.orbit-lab.org/kernel/compat-wireless-2.6-stable/v2.6.38/compat-wireless-2.6.38.2-2.tar.bz2 ) and installed everything I need according to this webpage: http://acx100.erley.org/stable.html Once issueing modprobe ath5k, putting the interface up and waiting for ~30sec, I get a kernel panic. Could this be a bug or am I doing something wrong? The error only occurrs after putting the interface up. If I don't do so, the error won't be there. Here is some output from the machine: demo00000001:~# modprobe ath5k && ifconfig wlan0 up [ 48.363894] Compat-wireless backport release: compat-wireless-2.6.38.2-2 [ 48.372351] Backport based on linux-2.6-allstable.git v2.6.38.2 [ 48.411748] cfg80211: Calling CRDA to update world regulatory domain [ 48.517969] ath5k 0000:09:00.0: using bridge 0000:00:1c.2 INT A to get IRQ 17 [ 48.526919] ath5k 0000:09:00.0: PCI->APIC IRQ transform: INT A -> IRQ 17 [ 48.534315] ath5k 0000:09:00.0: registered as 'phy0' [ 49.162919] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70) demo00000001:~# [ 77.953752] ------------[ cut here ]------------ [ 77.958711] WARNING: at /home/dborgmann/downloads/compat-wireless-2.6.38.2-2/net/mac80211/rx.c:2827 ieee80211_rx+0x38/0x6fe [mac80211]() [ 77.971856] Hardware name: Luna Pier CRB [ 77.976049] Modules linked in: [last unloaded: scsi_wait_scan] [ 77.982354] Pid: 9, comm: sirq-tasklet/0 Not tainted 2.6.33.9-rt31-atom-ssb #1 [ 77.990090] Call Trace: [ 77.992732] [<c011852f>] warn_slowpath_common+0x65/0x7c [ 77.998419] [<e0024ad1>] ? ieee80211_rx+0x38/0x6fe [mac80211] [ 78.004672] [<c0118553>] warn_slowpath_null+0xd/0x10 [ 78.010119] [<e0024ad1>] ieee80211_rx+0x38/0x6fe [mac80211] [ 78.016157] [<c022d6e8>] ? __alloc_skb+0x4c/0x110 [ 78.021296] [<c0106297>] ? nommu_map_page+0x3c/0x51 [ 78.026648] [<e00992c9>] ? ath5k_rx_skb_alloc+0x99/0x10a [ath5k] [ 78.033190] [<e009b989>] ath5k_tasklet_rx+0x59f/0x60b [ath5k] [ 78.039454] [<c011c486>] __tasklet_action.clone.8+0x76/0xd1 [ 78.045502] [<c011c529>] tasklet_action+0x23/0x25 [ 78.050640] [<c011c285>] run_ksoftirqd+0xf0/0x19b [ 78.055788] [<c011c195>] ? run_ksoftirqd+0x0/0x19b [ 78.061032] [<c0127829>] kthread+0x5e/0x63 [ 78.065538] [<c01277cb>] ? kthread+0x0/0x63 [ 78.070107] [<c0102bb6>] kernel_thread_helper+0x6/0x10 [ 78.075695] ---[ end trace 6b864a3c0aa1a8eb ]--- Best regards, Dennis ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 2011-05-11 10:38 [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 Dennis Borgmann @ 2011-05-23 16:21 ` Dennis Borgmann 2011-05-23 16:35 ` Ben Greear 0 siblings, 1 reply; 6+ messages in thread From: Dennis Borgmann @ 2011-05-23 16:21 UTC (permalink / raw) To: linux-wireless Hello linux-wireless list! Is there really no one with an idea? Is there no one among the developers, who is interested in this bug, if it is a bug? I'm starting to lose my hope... Dennis Am 11.05.2011 12:38, schrieb Dennis Borgmann: > Hello linux-wireless list! > > I am using a Sparklan WPEA-166G/W with Chipset AR5BXB63 Rev. 11 (it's > a MiniPCI-card) in an embedded X86-System (Pipal 2140U, Intel ATOM > processor). It's running voyage-0.6.5, which essentially is a Debian > Lenny System. > > I am running kernel 2.6.33.9-rt31: > > demo00000001:~# uname -a > Linux SSB_wlan-demo00000001 2.6.33.9-rt31-atom-ssb #1 PREEMPT RT Mon > May 9 18:25:28 CEST 2011 i686 GNU/Linux > > I installed the compat-wireless drivers version 2.6.38.2-2 ( > http://www.orbit-lab.org/kernel/compat-wireless-2.6-stable/v2.6.38/compat-wireless-2.6.38.2-2.tar.bz2 > ) and installed everything I need according to this webpage: > http://acx100.erley.org/stable.html > > Once issueing modprobe ath5k, putting the interface up and waiting for > ~30sec, I get a kernel panic. Could this be a bug or am I doing > something wrong? > > The error only occurrs after putting the interface up. If I don't do > so, the error won't be there. > > Here is some output from the machine: > > demo00000001:~# modprobe ath5k && ifconfig wlan0 up > [ 48.363894] Compat-wireless backport release: > compat-wireless-2.6.38.2-2 > [ 48.372351] Backport based on linux-2.6-allstable.git v2.6.38.2 > [ 48.411748] cfg80211: Calling CRDA to update world regulatory domain > [ 48.517969] ath5k 0000:09:00.0: using bridge 0000:00:1c.2 INT A to > get IRQ 17 > [ 48.526919] ath5k 0000:09:00.0: PCI->APIC IRQ transform: INT A -> > IRQ 17 > [ 48.534315] ath5k 0000:09:00.0: registered as 'phy0' > [ 49.162919] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: > 0x70) > demo00000001:~# [ 77.953752] ------------[ cut here ]------------ > [ 77.958711] WARNING: at > /home/dborgmann/downloads/compat-wireless-2.6.38.2-2/net/mac80211/rx.c:2827 > ieee80211_rx+0x38/0x6fe [mac80211]() > [ 77.971856] Hardware name: Luna Pier CRB > [ 77.976049] Modules linked in: [last unloaded: scsi_wait_scan] > [ 77.982354] Pid: 9, comm: sirq-tasklet/0 Not tainted > 2.6.33.9-rt31-atom-ssb #1 > [ 77.990090] Call Trace: > [ 77.992732] [<c011852f>] warn_slowpath_common+0x65/0x7c > [ 77.998419] [<e0024ad1>] ? ieee80211_rx+0x38/0x6fe [mac80211] > [ 78.004672] [<c0118553>] warn_slowpath_null+0xd/0x10 > [ 78.010119] [<e0024ad1>] ieee80211_rx+0x38/0x6fe [mac80211] > [ 78.016157] [<c022d6e8>] ? __alloc_skb+0x4c/0x110 > [ 78.021296] [<c0106297>] ? nommu_map_page+0x3c/0x51 > [ 78.026648] [<e00992c9>] ? ath5k_rx_skb_alloc+0x99/0x10a [ath5k] > [ 78.033190] [<e009b989>] ath5k_tasklet_rx+0x59f/0x60b [ath5k] > [ 78.039454] [<c011c486>] __tasklet_action.clone.8+0x76/0xd1 > [ 78.045502] [<c011c529>] tasklet_action+0x23/0x25 > [ 78.050640] [<c011c285>] run_ksoftirqd+0xf0/0x19b > [ 78.055788] [<c011c195>] ? run_ksoftirqd+0x0/0x19b > [ 78.061032] [<c0127829>] kthread+0x5e/0x63 > [ 78.065538] [<c01277cb>] ? kthread+0x0/0x63 > [ 78.070107] [<c0102bb6>] kernel_thread_helper+0x6/0x10 > [ 78.075695] ---[ end trace 6b864a3c0aa1a8eb ]--- > > > Best regards, > Dennis ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 2011-05-23 16:21 ` Dennis Borgmann @ 2011-05-23 16:35 ` Ben Greear 2011-05-24 19:11 ` Dennis Borgmann 2011-05-24 20:03 ` Dennis Borgmann 0 siblings, 2 replies; 6+ messages in thread From: Ben Greear @ 2011-05-23 16:35 UTC (permalink / raw) To: Dennis Borgmann; +Cc: linux-wireless On 05/23/2011 09:21 AM, Dennis Borgmann wrote: > Hello linux-wireless list! > > Is there really no one with an idea? Is there no one among the > developers, who is interested in this bug, if it is a bug? > > I'm starting to lose my hope... Can you reproduce this in the wireless-testing tree? Ben -- Ben Greear <greearb@candelatech.com> Candela Technologies Inc http://www.candelatech.com ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 2011-05-23 16:35 ` Ben Greear @ 2011-05-24 19:11 ` Dennis Borgmann 2011-05-24 20:03 ` Dennis Borgmann 1 sibling, 0 replies; 6+ messages in thread From: Dennis Borgmann @ 2011-05-24 19:11 UTC (permalink / raw) To: Ben Greear; +Cc: linux-wireless Problem has been solved by using latest compat-wireless-2.6.39-1 from last night. Finally. Thank you, linux-wireless folks! Best regards, Dennis Am 23.05.2011 18:35, schrieb Ben Greear: > On 05/23/2011 09:21 AM, Dennis Borgmann wrote: >> Hello linux-wireless list! >> >> Is there really no one with an idea? Is there no one among the >> developers, who is interested in this bug, if it is a bug? >> >> I'm starting to lose my hope... > > Can you reproduce this in the wireless-testing tree? > > Ben > ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 2011-05-23 16:35 ` Ben Greear 2011-05-24 19:11 ` Dennis Borgmann @ 2011-05-24 20:03 ` Dennis Borgmann 2011-05-24 20:47 ` Ben Greear 1 sibling, 1 reply; 6+ messages in thread From: Dennis Borgmann @ 2011-05-24 20:03 UTC (permalink / raw) To: Ben Greear; +Cc: linux-wireless Dear linux-wireless list, sorry, I did answer too early, problem still exists. I am now using compat-wireless-2.6.39-1. I hope, this is new enough (it seems to be from last night anyway...) I now even exchanged the wireless card, now I am using a Gigabyte GN-WI01HT (AR5414 chip), the problem seems to be the same. I attached some dmesg info. Could this be a hardware error of the mainboard? Actually, I only have one hardware to test on and I somehow don't really trust it. Just a thought of mine... What are your suggestions, or could this really be a bug? Best regards, Dennis [ 7.525432] Compat-wireless backport release: compat-wireless-v2.6.39-1 [ 7.532737] Backport based on linux-2.6-allstable.git v2.6.39 [ 7.576502] cfg80211: Calling CRDA to update world regulatory domain [ 7.640147] cfg80211: World regulatory domain updated: [ 7.645908] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 7.656157] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.664483] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 7.672754] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 7.674546] ath5k 0000:11:07.0: PCI->APIC IRQ transform: INT A -> IRQ 19 [ 7.688710] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.697046] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.705453] ath5k 0000:11:07.0: registered as 'phy0' [ 8.351679] ath: EEPROM regdomain: 0x0 [ 8.351685] ath: EEPROM indicates default country code should be used [ 8.351690] ath: doing EEPROM country->regdmn map search [ 8.351695] ath: country maps to regdmn code: 0x3a [ 8.351699] ath: Country alpha2 being used: US [ 8.351703] ath: Regpair used: 0x3a [ 8.360800] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 8.362487] cfg80211: Calling CRDA for country: US [ 8.362536] ath5k phy0: Atheros AR5414 chip found (MAC: 0xa5, PHY: 0x61) [ 8.363657] modprobe used greatest stack depth: 5860 bytes left [ 8.388493] cfg80211: Regulatory domain changed to country: US [ 8.394937] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 8.403724] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 8.412246] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 8.421561] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.430451] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.438853] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.447623] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 8.496322] scsi 4:0:0:0: Direct-Access Generic Storage Device 0.00 PQ: 0 ANSI: 2 [ 8.505354] sd 4:0:0:0: Attached scsi generic sg1 type 0 [ 8.511989] sd 4:0:0:0: [sdb] Attached SCSI removable disk [ 8.796704] chown used greatest stack depth: 5824 bytes left [ 27.909475] cfg80211: Calling CRDA for country: DE [ 27.920079] cfg80211: Regulatory domain changed to country: DE [ 27.927544] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 27.937610] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 27.945562] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 27.953475] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 27.961475] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm) [ 28.014622] hostapd used greatest stack depth: 5748 bytes left [ 33.195098] ------------[ cut here ]------------ [ 33.201175] WARNING: at /mnt/entw/compat-wireless-2.6.39-1/net/mac80211/rx.c:2882 ieee80211_rx+0x39/0x660 [mac80211]() [ 33.213802] Hardware name: Luna Pier CRB [ 33.219331] Modules linked in: ath5k ath mac80211 cfg80211 compat [last unloaded: scsi_wait_scan] [ 33.226899] Pid: 24, comm: sirq-tasklet/1 Not tainted 2.6.33.7.2-rt30-atom-ssb #1 [ 33.236137] Call Trace: [ 33.240118] [<c1030666>] warn_slowpath_common+0x60/0x90 [ 33.247071] [<c10306a3>] warn_slowpath_null+0xd/0x10 [ 33.253762] [<dff60edd>] ieee80211_rx+0x39/0x660 [mac80211] [ 33.261111] [<e031064c>] ath5k_tasklet_rx+0x540/0x5aa [ath5k] [ 33.268566] [<c102b281>] ? set_next_entity+0x1e/0x89 [ 33.273935] [<c135941d>] ? __schedule+0x76f/0x7a4 [ 33.280319] [<c10356b4>] __tasklet_action+0x77/0xd7 [ 33.285564] [<c10357d2>] tasklet_action+0x5c/0x62 [ 33.291956] [<c1035c19>] run_ksoftirqd+0x131/0x247 [ 33.297091] [<c1035ae8>] ? run_ksoftirqd+0x0/0x247 [ 33.303589] [<c1046ab6>] kthread+0x61/0x66 [ 33.308029] [<c1046a55>] ? kthread+0x0/0x66 [ 33.313884] [<c1002db6>] kernel_thread_helper+0x6/0x10 [ 33.319430] ---[ end trace 95aeede189daca6f ]--- Am 23.05.2011 18:35, schrieb Ben Greear: > On 05/23/2011 09:21 AM, Dennis Borgmann wrote: >> Hello linux-wireless list! >> >> Is there really no one with an idea? Is there no one among the >> developers, who is interested in this bug, if it is a bug? >> >> I'm starting to lose my hope... > > Can you reproduce this in the wireless-testing tree? > > Ben > ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 2011-05-24 20:03 ` Dennis Borgmann @ 2011-05-24 20:47 ` Ben Greear 0 siblings, 0 replies; 6+ messages in thread From: Ben Greear @ 2011-05-24 20:47 UTC (permalink / raw) To: Dennis Borgmann; +Cc: linux-wireless On 05/24/2011 01:03 PM, Dennis Borgmann wrote: > Dear linux-wireless list, > > sorry, I did answer too early, problem still exists. I am now using > compat-wireless-2.6.39-1. I hope, this is new enough (it seems to be > from last night anyway...) > > I now even exchanged the wireless card, now I am using a Gigabyte > GN-WI01HT (AR5414 chip), the problem seems to be the same. I attached > some dmesg info. Could this be a hardware error of the mainboard? > Actually, I only have one hardware to test on and I somehow don't really > trust it. Just a thought of mine... > > What are your suggestions, or could this really be a bug? I use the wireless-testing tree, not any compat stuff. We are testing ath5k and ath9k currently, and no troubles. If you can reproduce it using wireless-testing, I'll look at it closer. Otherwise, it might be some problem with the backport. Thanks, Ben > > Best regards, > Dennis > > > [ 7.525432] Compat-wireless backport release: compat-wireless-v2.6.39-1 > [ 7.532737] Backport based on linux-2.6-allstable.git v2.6.39 > [ 7.576502] cfg80211: Calling CRDA to update world regulatory domain > [ 7.640147] cfg80211: World regulatory domain updated: > [ 7.645908] cfg80211: (start_freq - end_freq @ bandwidth), > (max_antenna_gain, max_eirp) > [ 7.656157] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, > 2000 mBm) > [ 7.664483] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, > 2000 mBm) > [ 7.672754] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, > 2000 mBm) > [ 7.674546] ath5k 0000:11:07.0: PCI->APIC IRQ transform: INT A -> IRQ 19 > [ 7.688710] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, > 2000 mBm) > [ 7.697046] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, > 2000 mBm) > [ 7.705453] ath5k 0000:11:07.0: registered as 'phy0' > [ 8.351679] ath: EEPROM regdomain: 0x0 > [ 8.351685] ath: EEPROM indicates default country code should be used > [ 8.351690] ath: doing EEPROM country->regdmn map search > [ 8.351695] ath: country maps to regdmn code: 0x3a > [ 8.351699] ath: Country alpha2 being used: US > [ 8.351703] ath: Regpair used: 0x3a > [ 8.360800] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' > [ 8.362487] cfg80211: Calling CRDA for country: US > [ 8.362536] ath5k phy0: Atheros AR5414 chip found (MAC: 0xa5, PHY: 0x61) > [ 8.363657] modprobe used greatest stack depth: 5860 bytes left > [ 8.388493] cfg80211: Regulatory domain changed to country: US > [ 8.394937] cfg80211: (start_freq - end_freq @ bandwidth), > (max_antenna_gain, max_eirp) > [ 8.403724] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, > 2700 mBm) > [ 8.412246] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, > 1700 mBm) > [ 8.421561] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, > 2000 mBm) > [ 8.430451] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, > 2000 mBm) > [ 8.438853] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, > 2000 mBm) > [ 8.447623] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, > 3000 mBm) > [ 8.496322] scsi 4:0:0:0: Direct-Access Generic Storage Device 0.00 PQ: > 0 ANSI: 2 > [ 8.505354] sd 4:0:0:0: Attached scsi generic sg1 type 0 > [ 8.511989] sd 4:0:0:0: [sdb] Attached SCSI removable disk > [ 8.796704] chown used greatest stack depth: 5824 bytes left > [ 27.909475] cfg80211: Calling CRDA for country: DE > [ 27.920079] cfg80211: Regulatory domain changed to country: DE > [ 27.927544] cfg80211: (start_freq - end_freq @ bandwidth), > (max_antenna_gain, max_eirp) > [ 27.937610] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, > 2000 mBm) > [ 27.945562] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, > 2000 mBm) > [ 27.953475] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, > 2000 mBm) > [ 27.961475] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, > 2698 mBm) > [ 28.014622] hostapd used greatest stack depth: 5748 bytes left > [ 33.195098] ------------[ cut here ]------------ > [ 33.201175] WARNING: at > /mnt/entw/compat-wireless-2.6.39-1/net/mac80211/rx.c:2882 > ieee80211_rx+0x39/0x660 [mac80211]() > [ 33.213802] Hardware name: Luna Pier CRB > [ 33.219331] Modules linked in: ath5k ath mac80211 cfg80211 compat [last > unloaded: scsi_wait_scan] > [ 33.226899] Pid: 24, comm: sirq-tasklet/1 Not tainted > 2.6.33.7.2-rt30-atom-ssb #1 > [ 33.236137] Call Trace: > [ 33.240118] [<c1030666>] warn_slowpath_common+0x60/0x90 > [ 33.247071] [<c10306a3>] warn_slowpath_null+0xd/0x10 > [ 33.253762] [<dff60edd>] ieee80211_rx+0x39/0x660 [mac80211] > [ 33.261111] [<e031064c>] ath5k_tasklet_rx+0x540/0x5aa [ath5k] > [ 33.268566] [<c102b281>] ? set_next_entity+0x1e/0x89 > [ 33.273935] [<c135941d>] ? __schedule+0x76f/0x7a4 > [ 33.280319] [<c10356b4>] __tasklet_action+0x77/0xd7 > [ 33.285564] [<c10357d2>] tasklet_action+0x5c/0x62 > [ 33.291956] [<c1035c19>] run_ksoftirqd+0x131/0x247 > [ 33.297091] [<c1035ae8>] ? run_ksoftirqd+0x0/0x247 > [ 33.303589] [<c1046ab6>] kthread+0x61/0x66 > [ 33.308029] [<c1046a55>] ? kthread+0x0/0x66 > [ 33.313884] [<c1002db6>] kernel_thread_helper+0x6/0x10 > [ 33.319430] ---[ end trace 95aeede189daca6f ]--- > > > Am 23.05.2011 18:35, schrieb Ben Greear: >> On 05/23/2011 09:21 AM, Dennis Borgmann wrote: >>> Hello linux-wireless list! >>> >>> Is there really no one with an idea? Is there no one among the >>> developers, who is interested in this bug, if it is a bug? >>> >>> I'm starting to lose my hope... >> >> Can you reproduce this in the wireless-testing tree? >> >> Ben >> -- Ben Greear <greearb@candelatech.com> Candela Technologies Inc http://www.candelatech.com ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2011-05-24 20:47 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2011-05-11 10:38 [ath5k] kernel panic while using compat-wireless-2.6.38.2-2 Dennis Borgmann 2011-05-23 16:21 ` Dennis Borgmann 2011-05-23 16:35 ` Ben Greear 2011-05-24 19:11 ` Dennis Borgmann 2011-05-24 20:03 ` Dennis Borgmann 2011-05-24 20:47 ` Ben Greear
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).