From: Chiefdome <chiefdome@googlemail.com>
To: linux-wireless@vger.kernel.org
Subject: Re: Alfa AWUS036NHR with RTL8188RU chipset
Date: Tue, 20 Sep 2011 04:27:09 +0200 [thread overview]
Message-ID: <4E77F9FD.1020204@googlemail.com> (raw)
In-Reply-To: <4E77F631.3030202@googlemail.com>
On 09/20/2011 04:10 AM, Chiefdome wrote:
> Hi there,
>
> i just bought an Alfa AWUS036NHR for testing.
> It runs with the rtl8192cu driver.
> I have a question because sometimes the wireless adapter dont shows
> any networks no longer.
> I have to reload the module an then its showing some networks.
>
> In dmesg it shows:
>
> [ 262.219575] ADDRCONF(NETDEV_UP): wlan1: link is not ready
> [ 269.770133] ADDRCONF(NETDEV_UP): wlan1: link is not ready
> [ 270.947047] ADDRCONF(NETDEV_UP): wlan1: link is not ready
>
>
> For any further output please let me know.
A complete dmesg output can be seen here, because theres also a problem
when associating to a network:
[ 1455.353142] cfg80211: All devices are disconnected, going to restore
regulatory settings
[ 1455.353155] cfg80211: Restoring regulatory settings
[ 1455.353165] cfg80211: Calling CRDA to update world regulatory domain
[ 1455.361425] cfg80211: Ignoring regulatory request Set by core since
the driver uses its own custom regulatory domain
[ 1455.361436] cfg80211: Ignoring regulatory request Set by core since
the driver uses its own custom regulatory domain
[ 1455.361442] cfg80211: World regulatory domain updated:
[ 1455.361447] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 1455.361454] cfg80211: (2400000 KHz - 2494000 KHz @ 40000 KHz),
(N/A, 3301 mBm)
[ 1455.361460] cfg80211: (4910000 KHz - 5895000 KHz @ 40000 KHz),
(N/A, 3301 mBm)
[ 1455.403456] iwlagn 0000:03:00.0: L1 Disabled; Enabling L0S
[ 1455.403856] iwlagn 0000:03:00.0: Radio type=0x0-0x2-0x0
[ 1455.459585] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1455.950477] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 1456.010220] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 1456.011668] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1495.264204] rtl8192cu: MAC auto ON okay!
[ 1495.299099] rtl8192cu: Tx queue select: 0x05
[ 1495.299880] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 1495.709590] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 1500.741392] usbcore: deregistering interface driver rtl8192cu
[ 1505.097104] rtl8192cu: MAC address: 00:c0:ca:52:cb:4c
[ 1505.097116] rtl8192cu: Board Type 1
[ 1505.102441] rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 1505.102454] cfg80211: Updating information on frequency 2412 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102462] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102468] cfg80211: Updating information on frequency 2417 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102475] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102480] cfg80211: Updating information on frequency 2422 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102487] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102493] cfg80211: Updating information on frequency 2427 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102499] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102505] cfg80211: Updating information on frequency 2432 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102511] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102517] cfg80211: Updating information on frequency 2437 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102523] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102529] cfg80211: Updating information on frequency 2442 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102536] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102541] cfg80211: Updating information on frequency 2447 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102548] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102553] cfg80211: Updating information on frequency 2452 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102560] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102565] cfg80211: Updating information on frequency 2457 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102572] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102578] cfg80211: Updating information on frequency 2462 MHz for
a 20 MHz width channel with regulatory rule:
[ 1505.102584] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi,
2000 mBm)
[ 1505.102590] cfg80211: Disabling freq 2467 MHz as custom regd has no
rule that fits a 20 MHz wide channel
[ 1505.102595] cfg80211: Disabling freq 2472 MHz as custom regd has no
rule that fits a 20 MHz wide channel
[ 1505.102601] cfg80211: Disabling freq 2484 MHz as custom regd has no
rule that fits a 20 MHz wide channel
[ 1505.103549] cfg80211: Ignoring regulatory request Set by core since
the driver uses its own custom regulatory domain
[ 1505.103803] ieee80211 phy2: Selected rate control algorithm 'rtl_rc'
[ 1505.105949] usbcore: registered new interface driver rtl8192cu
[ 1513.004969] rtl8192cu: MAC auto ON okay!
[ 1513.038127] rtl8192cu: Tx queue select: 0x05
[ 1513.038878] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 1513.443284] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 1519.568596] rtl8192cu: MAC auto ON okay!
[ 1519.601476] rtl8192cu: Tx queue select: 0x05
[ 1519.602253] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 1520.008221] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 1520.350447] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 1520.410244] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 1520.411607] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1520.619096] rtl8192cu: MAC auto ON okay!
[ 1520.651975] rtl8192cu: Tx queue select: 0x05
[ 1520.652755] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 1521.060567] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 1524.272807] wlan1: authenticate with [MAC-ADDRESS] (try 1)
[ 1524.299985] wlan1: authenticated
[ 1524.300029] wlan1: associate with [MAC-ADDRESS] (try 1)
[ 1524.309323] wlan1: RX AssocResp from [MAC-ADDRESS] (capab=0x431
status=0 aid=1)
[ 1524.309331] wlan1: associated
[ 1524.311767] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 1525.172880] type=1400 audit(1316485102.702:35): apparmor="DENIED"
operation="open" parent=5409 profile="/sbin/dhclient"
name="/var/lib/wicd/dhclient.conf" pid=5445 comm="dhclient"
requested_mask="r" denied_mask="r" fsuid=0 ouid=0
[ 1534.590028] wlan1: no IPv6 routers present
next prev parent reply other threads:[~2011-09-20 2:27 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-20 2:10 Alfa AWUS036NHR with RTL8188RU chipset Chiefdome
2011-09-20 2:27 ` Chiefdome [this message]
2011-09-20 3:05 ` Larry Finger
2011-09-20 9:32 ` Chiefdome
2011-09-20 21:38 ` Chiefdome
2011-09-20 22:32 ` Larry Finger
2011-09-21 0:02 ` Larry Finger
2011-09-21 9:43 ` Chiefdome
2011-09-21 14:45 ` Larry Finger
2011-09-21 19:19 ` Chiefdome
2011-09-21 20:03 ` Larry Finger
2011-09-21 20:28 ` Chiefdome
2011-09-21 20:37 ` Larry Finger
2011-09-21 20:39 ` Chiefdome
2011-09-21 20:41 ` Chiefdome
2011-09-21 21:09 ` Larry Finger
2011-09-30 14:20 ` v4mp
2011-09-30 15:18 ` Larry Finger
2011-09-30 18:14 ` v4mp
2011-10-06 16:25 ` Toddy
2011-10-06 22:06 ` Larry Finger
2011-10-08 16:24 ` Toddy
2011-10-08 16:52 ` Larry Finger
2011-10-08 23:29 ` Gábor Stefanik
2011-10-09 14:21 ` v4mp
2011-10-09 14:47 ` Larry Finger
2011-10-15 14:22 ` v4mp
2011-10-16 2:49 ` Larry Finger
2011-10-17 10:07 ` v4mp
2011-10-17 14:59 ` Larry Finger
2011-10-17 17:09 ` v4mp
2011-10-17 18:38 ` Larry Finger
2011-10-18 3:23 ` Larry Finger
2011-10-18 12:44 ` v4mp
2011-10-18 13:07 ` v4mp
2011-10-18 15:20 ` Larry Finger
2011-10-18 21:50 ` v4mp
2011-10-18 23:01 ` Larry Finger
2011-10-19 8:17 ` v4mp
2011-10-19 12:08 ` Larry Finger
2011-10-19 14:37 ` v4mp
2011-10-20 3:38 ` Larry Finger
2011-10-20 9:47 ` v4mp
2011-10-20 13:35 ` Larry Finger
2011-10-26 15:49 ` Chiefdome
2011-10-26 16:12 ` Larry Finger
2011-10-26 19:39 ` Chiefdome
2011-10-26 21:20 ` Larry Finger
2011-10-26 21:31 ` Larry Finger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E77F9FD.1020204@googlemail.com \
--to=chiefdome@googlemail.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).