From: Chiefdome <chiefdome@googlemail.com>
To: Larry Finger <Larry.Finger@lwfinger.net>
Cc: george0505@realtek.com, linux-wireless@vger.kernel.org
Subject: Re: Alfa AWUS036NHR with RTL8188RU chipset
Date: Wed, 21 Sep 2011 21:19:44 +0200 [thread overview]
Message-ID: <4E7A38D0.7070304@googlemail.com> (raw)
In-Reply-To: <4E79F87F.1050402@lwfinger.net>
On 09/21/2011 04:45 PM, Larry Finger wrote:
> On 09/21/2011 04:43 AM, Chiefdome wrote:
>> I tried the latest git repo from
>> git://git.infradead.org/users/linville/wireless-next.
>> Same story here.
>> After disconnecting to the network, I have to reload the module only
>> then
>> networks are seen.
>
> I just cloned the wireless-next tree. The two patches mentioned in my
> previous Email are included.
>
> Please run the following command sequence and send us the dmesg output
> after your failure occurs:
>
> modprobe -rv rtl8192cu
> modprobe -v rtlwifi debug=3
> modprobe -v rtl8192cu
>
> Larry
I have found another bug - it is impossible to me to connect a
WPA2-network - here is the dmesg output for that - will send you the
output for a WEP-network later then:
[ 194.011573] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 194.230135] rtl8192cu: MAC auto ON okay!
[ 194.263015] rtl8192cu: Tx queue select: 0x05
[ 194.263820] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 194.670927] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 237.379814] rtl8192cu: MAC auto ON okay!
[ 237.413488] rtl8192cu: Tx queue select: 0x05
[ 237.414243] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 237.821229] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 238.160462] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 238.220187] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 238.221641] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 278.340442] usbcore: deregistering interface driver rtl8192cu
[ 326.145824] rtl8192cu:rtl92cu_read_eeprom_info():<0-0> Boot from EFUSE
[ 326.223617] rtl8192cu: MAC address: [MAC-ADDRESS]
[ 326.223629] rtl8192cu:_rtl92cu_read_adapter_info():<0-0> VID = 0xbda
PID = 0x817f
[ 326.223636] rtl8192cu: Board Type 1
[ 326.223641] rtl8192cu:_rtl92cu_hal_customized_behavior():<0-0> RT
Customized ID: 0x00
[ 326.227751] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x81),
MaxPacketSize=512 ,Interval=0.
[ 326.227762] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x02),
MaxPacketSize=512 ,Interval=0.
[ 326.227770] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x03),
MaxPacketSize=512 ,Interval=0.
[ 326.227777] rtlwifi:_rtl_usb_init():<0-0> USB EP(0x84),
MaxPacketSize=64 ,Interval=1.
[ 326.228202] rtl8192cu:_TwoOutEpMapping():<0-0> USB typical Setting.....
[ 326.228209] rtlwifi:_rtl_usb_init_tx():<0-0> USB Max Bulk-out Size=512
[ 326.228217] rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 326.228223] rtlwifi:_rtl_init_hw_ht_capab():<0-0> 1T1R
[ 326.228234] cfg80211: Updating information on frequency 2412 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228241] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228247] cfg80211: Updating information on frequency 2417 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228253] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228259] cfg80211: Updating information on frequency 2422
MH00:1c:4a:03:b9:64z for a 20 MHz width channel with regulatory rule:
[ 326.228266] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228271] cfg80211: Updating information on frequency 2427 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228278] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228284] cfg80211: Updating information on frequency 2432 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228290] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228296] cfg80211: Updating information on frequency 2437 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228302] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228308] cfg80211: Updating information on frequency 2442 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228314] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228320] cfg80211: Updating information on frequency 2447 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228327] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228332] cfg80211: Updating information on frequency 2452 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228339] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228344] cfg80211: Updating information on frequency 2457 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228351] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228356] cfg80211: Updating information on frequency 2462 MHz for
a 20 MHz width channel with regulatory rule:
[ 326.228363] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A
mBi, 2000 mBm)
[ 326.228369] cfg80211: Disabling freq 2467 MHz as custom regd has no
rule that fits a 20 MHz wide channel
[ 326.228374] cfg80211: Disabling freq 2472 MHz as custom regd has no
rule that fits a 20 MHz wide channel
[ 326.228380] cfg80211: Disabling freq 2484 MHz as custom regd has no
rule that fits a 20 MHz wide channel
[ 326.228554] cfg80211: Ignoring regulatory request Set by core since
the driver uses its own custom regulatory domain
[ 326.228881] ieee80211 phy2: Selected rate control algorithm 'rtl_rc'
[ 326.234614] usbcore: registered new interface driver rtl8192cu
[ 330.227015] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
[ 330.228731] rtl8192cu: MAC auto ON okay!
[ 330.264497] rtl8192cu: Tx queue select: 0x05
[ 330.264507] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
type to NO LINK!
[ 330.265249] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
driver sleep or unload
[ 330.265265] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 330.265269] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
Version(63), Signature(0x88c1),Size(32)
[ 330.658702] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002a0e) ###
[ 330.658734] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
HW_VAR_RETRY_LIMIT(0x00000004)
[ 330.670568] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 340.000671] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002a0e) ###
[ 340.016768] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
[ 340.018500] rtl8192cu: MAC auto ON okay!
[ 340.051808] rtl8192cu: Tx queue select: 0x05
[ 340.051828] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
type to NO LINK!
[ 340.052543] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
driver sleep or unload
[ 340.052583] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 340.052590] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
Version(63), Signature(0x88c1),Size(32)
[ 340.450345] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002ace) ###
[ 340.450367] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
HW_VAR_RETRY_LIMIT(0x00000004)
[ 340.462324] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 340.810935] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 340.870239] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 340.871685] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 340.960624] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002a0e) ###
[ 341.088320] rtl8192cu:_rtl92cu_init_power_on():<0-0> Autoload Done!
[ 341.091812] rtl8192cu: MAC auto ON okay!
[ 341.128338] rtl8192cu: Tx queue select: 0x05
[ 341.128356] rtl8192cu:rtl92c_set_network_type():<0-0> Set Network
type to NO LINK!
[ 341.129072] rtl8192c_common:rtl92c_phy_set_bw_mode():<0-0> FALSE
driver sleep or unload
[ 341.129112] rtl8192c_common: Loading firmware file
rtlwifi/rtl8192cufw.bin
[ 341.129119] rtl8192c_common:rtl92c_download_fw():<0-0> Firmware
Version(63), Signature(0x88c1),Size(32)
[ 341.523259] rtl8192cu:rtl92cu_set_hw_reg():<0-0> ### Set
RCR(0xf0002ace) ###
[ 341.523296] rtl8192cu:rtl92cu_set_hw_reg():<0-0> Set
HW_VAR_RETRY_LIMIT(0x00000004)
[ 341.535132] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 344.553546] wlan1: direct probe to [MAC-ADDRESS] (try 1/3)
[ 344.750275] wlan1: direct probe to [MAC-ADDRESS] (try 2/3)
[ 344.950061] wlan1: direct probe to [MAC-ADDRESS] (try 3/3)
[ 345.150150] wlan1: direct probe to [MAC-ADDRESS] timed out
next prev parent reply other threads:[~2011-09-21 19:19 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-20 2:10 Alfa AWUS036NHR with RTL8188RU chipset Chiefdome
2011-09-20 2:27 ` Chiefdome
2011-09-20 3:05 ` Larry Finger
2011-09-20 9:32 ` Chiefdome
2011-09-20 21:38 ` Chiefdome
2011-09-20 22:32 ` Larry Finger
2011-09-21 0:02 ` Larry Finger
2011-09-21 9:43 ` Chiefdome
2011-09-21 14:45 ` Larry Finger
2011-09-21 19:19 ` Chiefdome [this message]
2011-09-21 20:03 ` Larry Finger
2011-09-21 20:28 ` Chiefdome
2011-09-21 20:37 ` Larry Finger
2011-09-21 20:39 ` Chiefdome
2011-09-21 20:41 ` Chiefdome
2011-09-21 21:09 ` Larry Finger
2011-09-30 14:20 ` v4mp
2011-09-30 15:18 ` Larry Finger
2011-09-30 18:14 ` v4mp
2011-10-06 16:25 ` Toddy
2011-10-06 22:06 ` Larry Finger
2011-10-08 16:24 ` Toddy
2011-10-08 16:52 ` Larry Finger
2011-10-08 23:29 ` Gábor Stefanik
2011-10-09 14:21 ` v4mp
2011-10-09 14:47 ` Larry Finger
2011-10-15 14:22 ` v4mp
2011-10-16 2:49 ` Larry Finger
2011-10-17 10:07 ` v4mp
2011-10-17 14:59 ` Larry Finger
2011-10-17 17:09 ` v4mp
2011-10-17 18:38 ` Larry Finger
2011-10-18 3:23 ` Larry Finger
2011-10-18 12:44 ` v4mp
2011-10-18 13:07 ` v4mp
2011-10-18 15:20 ` Larry Finger
2011-10-18 21:50 ` v4mp
2011-10-18 23:01 ` Larry Finger
2011-10-19 8:17 ` v4mp
2011-10-19 12:08 ` Larry Finger
2011-10-19 14:37 ` v4mp
2011-10-20 3:38 ` Larry Finger
2011-10-20 9:47 ` v4mp
2011-10-20 13:35 ` Larry Finger
2011-10-26 15:49 ` Chiefdome
2011-10-26 16:12 ` Larry Finger
2011-10-26 19:39 ` Chiefdome
2011-10-26 21:20 ` Larry Finger
2011-10-26 21:31 ` Larry Finger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E7A38D0.7070304@googlemail.com \
--to=chiefdome@googlemail.com \
--cc=Larry.Finger@lwfinger.net \
--cc=george0505@realtek.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).