From: "Arend van Spriel" <arend@broadcom.com>
To: "Hauke Mehrtens" <hauke@hauke-m.de>
Cc: linville@tuxdriver.com, brcm80211-dev-list@broadcom.com,
linux-wireless@vger.kernel.org
Subject: Re: [PATCH v2 00/18] brcmsmac: update to get SoCs working
Date: Tue, 3 Jul 2012 09:13:13 +0200 [thread overview]
Message-ID: <4FF29B89.3040300@broadcom.com> (raw)
In-Reply-To: <1341062181-28071-1-git-send-email-hauke@hauke-m.de>
On 06/30/2012 03:16 PM, Hauke Mehrtens wrote:
> This series contains some patches needed to get brcmsmac working on
> SoCs like the BCM4718.
> The last part which adds core rev 17 (used in the BCM4718) to the list
> of supported cores is missing, because we do not have a firmware
> supporting this core yet, but I extended the b43 fwcutter to generate
> a firmware which brcmsmac accepts. With this firmware my BCM4718
> works. I would appreciate an official firmware release from Broadcom
> adding support for this core.
> The final patch adding support for the BCM43224 is missing because
> the PCIe host controller on the BCM4718 still causes problems and I
> have to add some more read after writes into the code, for now it uses
> an ugly hack and sometimes the problems still occur.
>
> The wifi is not stable on the BCM4718, I had no problems connecting to
> my ath9k driven access point but I have problems connecting to my
> BCM47186 based AP running the vendor firmware with the Broadcom
> proprietary driver.
> I get 12MBit/s max with the BCM4718 connected to ath9k on the 2.4 GHz
> band and 35 MBit/s max with the BCM43224 on the 5Ghz band connected to
> a Broadcom based AP running the proprietary driver. This seams to be
> CPU bounced as I have over 50% sirq in both cases.
>
> brcmsmac starts on the BCM47186 (id: 0x5357), but it does not tx or rx
> any traffic.
>
> One patch extends the xmtfifo_sz array for more core revs, I just toke
> the values from the other phy-n cores and hope this is correct.
>
> These patches are depending on: "[PATCH v2 0/9] bcma misc updates" and
> based on wireless-testing.
>
> I will send a patch for bcma which converts the warning message when it
> found a PCI and not a PCIe card into a WARN.
>
> v2:
> - when something depends on a patch for bcma, which is not in
> wireless-testing yet, I add that to the commit comment.
> - removed changes for BCM43421 and BCM6362 as I do not have a device
> to test this.
> - xmtfifo_sz now starts at core rev 17 and contains the correct values
> for core rev 28
> - make brcms_c_chipmatch() also work for SoCs
> - typos and format changes
>
I have acked all patches, but would like to do some sanity testing today.
Gr. AvS
next prev parent reply other threads:[~2012-07-03 7:13 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-06-30 13:16 [PATCH v2 00/18] brcmsmac: update to get SoCs working Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 01/18] brcmsmac: remove PCIE() macro Hauke Mehrtens
2012-07-03 7:07 ` Arend van Spriel
2012-06-30 13:16 ` [PATCH v2 02/18] brcmsmac: remove PCI_FORCEHT() macro Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 03/18] brcmsmac: remove ai_get_buscore{type,rev}() Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 04/18] brcmsmac: use container_of instead of cast Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 05/18] brcmsmac: remove ai_findcore() Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 06/18] brcmsmac: remove si_pmu_init() and si_pmu_res_init() Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 07/18] brcmsmac: remove si_pmu_spuravoid_pllupdate() Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 08/18] brcmsmac: remove some redundant chip common workarounds Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 09/18] brcmsmac: use core id constants from bcma Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 10/18] brcmsmac: use chip and package " Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 11/18] brcmsmac: remove some unnessessacry casts and void pointer Hauke Mehrtens
2012-07-01 23:59 ` Julian Calaby
2012-07-02 7:54 ` Dominique Martinet
2012-07-02 17:44 ` Hauke Mehrtens
2012-07-02 23:01 ` Julian Calaby
2012-06-30 13:16 ` [PATCH v2 12/18] brcmsmac: add a conditions for core rev 17 again Hauke Mehrtens
2012-07-03 7:06 ` Arend van Spriel
2012-06-30 13:16 ` [PATCH v2 13/18] brcmsmac: add some workarounds for other chips again Hauke Mehrtens
2012-07-03 7:08 ` Arend van Spriel
2012-06-30 13:16 ` [PATCH v2 14/18] brcmsmac: extend xmtfifo_sz array Hauke Mehrtens
2012-07-02 0:01 ` Julian Calaby
2012-07-02 18:15 ` [PATCH v3 " Hauke Mehrtens
2012-07-03 7:08 ` [PATCH v2 " Arend van Spriel
2012-06-30 13:16 ` [PATCH v2 15/18] brcmsmac: fix DMA on SoCs Hauke Mehrtens
2012-07-03 7:10 ` Arend van Spriel
2012-06-30 13:16 ` [PATCH v2 16/18] brcmsmac: extend brcms_c_chipmatch() to also handle non PCIe devices Hauke Mehrtens
2012-07-03 7:11 ` Arend van Spriel
2012-06-30 13:16 ` [PATCH v2 17/18] brcmsmac: fix read in write_phy_reg Hauke Mehrtens
2012-06-30 13:16 ` [PATCH v2 18/18] brcmsmac: handle non PCI devices in the phy code Hauke Mehrtens
2012-07-03 7:11 ` Arend van Spriel
2012-07-02 0:04 ` [PATCH v2 00/18] brcmsmac: update to get SoCs working Julian Calaby
2012-07-03 7:13 ` Arend van Spriel [this message]
2012-07-06 18:35 ` John W. Linville
2012-07-08 19:10 ` Arend van Spriel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4FF29B89.3040300@broadcom.com \
--to=arend@broadcom.com \
--cc=brcm80211-dev-list@broadcom.com \
--cc=hauke@hauke-m.de \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).