From: Xose Vazquez Perez <xose.vazquez@gmail.com>
To: Thomas Rosenkranz <tom.rosary@googlemail.com>
Cc: linux-wireless <linux-wireless@vger.kernel.org>,
Larry Finger <Larry.Finger@lwfinger.net>
Subject: Re: FW: 0bda:819a RTL8188CUS WLAN doesn't work out of the box in downstream and upstreamkernel
Date: Tue, 05 Feb 2013 20:55:38 +0100 [thread overview]
Message-ID: <511163BA.7060902@gmail.com> (raw)
In-Reply-To: <CAOAX8-k-Nbx4Om8fkEHRW2jmZCxKpsMY6oEZMAvdEQpXWn9Mdw@mail.gmail.com>
On 02/05/2013 12:00 AM, Thomas Rosenkranz wrote:
Larry, are you able to identify the chip of that device
with the 8192cu output ?
what should he do ? open the device to see the chip ??
> [ 183.369324] rtw driver version=v3.4.4_xxxx.20120730
> [ 183.369330] Build at: Feb 4 2013 23:44:44
> [ 183.369400] usbcore: registered new interface driver rtl8192cu
> [ 183.370696] register rtw_netdev_ops to netdev_ops
> [ 183.370702] CHIP TYPE: RTL8188C_8192C
> [ 183.370706]
> [ 183.370707] usb_endpoint_descriptor(0):
> [ 183.370710] bLength=7
> [ 183.370711] bDescriptorType=5
> [ 183.370713] bEndpointAddress=81
> [ 183.370715] wMaxPacketSize=200
> [ 183.370717] bInterval=0
> [ 183.370719] RT_usb_endpoint_is_bulk_in = 1
> [ 183.370721]
> [ 183.370722] usb_endpoint_descriptor(1):
> [ 183.370724] bLength=7
> [ 183.370726] bDescriptorType=5
> [ 183.370727] bEndpointAddress=2
> [ 183.370729] wMaxPacketSize=200
> [ 183.370731] bInterval=0
> [ 183.370733] RT_usb_endpoint_is_bulk_out = 2
> [ 183.370735]
> [ 183.370736] usb_endpoint_descriptor(2):
> [ 183.370738] bLength=7
> [ 183.370739] bDescriptorType=5
> [ 183.370741] bEndpointAddress=3
> [ 183.370743] wMaxPacketSize=200
> [ 183.370744] bInterval=0
> [ 183.370746] RT_usb_endpoint_is_bulk_out = 3
> [ 183.370748]
> [ 183.370749] usb_endpoint_descriptor(3):
> [ 183.370751] bLength=7
> [ 183.370752] bDescriptorType=5
> [ 183.370754] bEndpointAddress=84
> [ 183.370756] wMaxPacketSize=40
> [ 183.370758] bInterval=1
> [ 183.370760] RT_usb_endpoint_is_int_in = 4, Interval = 1
> [ 183.370762] nr_endpoint=4, in_num=2, out_num=2
> [ 183.370764]
> [ 183.370765] USB_SPEED_HIGH
> [ 183.370905] Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C.
> [ 183.370912] RF_Type is 3!!
> [ 183.371259] EEPROM type is E-FUSE
> [ 183.371263] ====> ReadAdapterInfo8192C
> [ 183.371385] Boot from EFUSE, Autoload OK !
> [ 183.556146] EEPROMVID = 0x0bda
> [ 183.556150] EEPROMPID = 0x819a
> [ 183.556152] EEPROMCustomerID : 0x00
> [ 183.556154] EEPROMSubCustomerID: 0x00
> [ 183.556156] RT_CustomerID: 0x00
> [ 183.556159] _ReadMACAddress MAC Address from EFUSE = 00:1c:7b:a8:a8:f3
> [ 183.556163] EEPROMRegulatory = 0x1
> [ 183.556165] _ReadBoardType(3)
> [ 183.556167] BT Coexistance = disable
> [ 183.556170] RT_ChannelPlan: 0x0a
> [ 183.556172] _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(10) ,bSupportRemoteWakeup(0)
> [ 183.556176] ### PS params=> power_mgnt(1),usbss_enable(0) ###
> [ 183.556178] ### AntDivCfg(0)
> [ 183.556180] readAdapterInfo_8192CU(): REPLACEMENT = 1
> [ 183.556184] <==== ReadAdapterInfo8192C in 184 ms
> [ 183.556432] rtw_macaddr_cfg MAC Address = 00:1c:7b:a8:a8:f3
> [ 183.556436] MAC Address from pnetdev->dev_addr= 00:1c:7b:a8:a8:f3
> [ 183.557231] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
> [ 183.571360] bDriverStopped=1
> [ 183.572190] +871x_drv - drv_open, bup=0
> [ 183.576780] ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC
> [ 183.576786] FirmwareDownload92C accquire FW from embedded image
> [ 183.576790] fw_ver=v80, fw_subver=0, sig=0x88c0
> [ 183.608627] fw download ok!
> [ 183.608631] Set RF Chip ID to RF_6052 and RF type to 1T1R.
> [ 183.984930] IQK:Start!!!
> [ 183.996309] Path A IQK Success!!
> [ 184.004034] Path A IQK Success!!
> [ 184.008907] IQK: final_candidate is 0
> [ 184.008911] IQK: RegE94=ff RegE9C=d RegEA4=fd RegEAC=3fd RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
> [ 184.008914] Path A IQ Calibration Success !
> [ 184.122503] pdmpriv->TxPowerTrackControl = 1
> [ 184.127472] MAC Address from REG_MACID = 00:1c:7b:a8:a8:f3
> [ 184.127476] rtl8192cu_hal_init in 556ms
> [ 184.127480] MAC Address = 00:1c:7b:a8:a8:f3
> [ 184.132257] -871x_drv - drv_open, bup=1
> [ 184.133354] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 184.133824] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 184.133854] set_mode = IW_MODE_INFRA
> [ 184.150748] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
> [ 184.150763] set_mode = IW_MODE_INFRA
> [ 184.193691] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
> [ 185.543612] survey done event(25)
> [ 185.593007] IW_SCAN_THIS_ESSID, ssid=nicht dein WLAN, len=15
> [ 186.942758] survey done event(2d)
> [ 186.943996] wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM
> [ 186.944003] set_mode = IW_MODE_INFRA
> [ 186.944019]
> [ 186.944020] wpa_ie(length:22):
> [ 186.944024] 0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x02
> [ 186.944028] 0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00
> [ 186.944031] 0x00 0x0f 0xac 0x02 0x00 0x00 0x00 0x00
> [ 186.944045] =>rtw_wx_set_essid
> [ 186.944047] ssid=nicht dein WLAN, len=15
> [ 186.944052] Set SSID under fw_state=0x00000008
> [ 186.944058] [by_bssid:0][assoc_ssid:nicht dein WLAN][to_roaming:0] new candidate: nicht dein WLAN(00:15:0c:f1:0d:d0) rssi:-32
> [ 186.944077] rtw_select_and_join_from_scanned_queue: candidate: nicht dein WLAN(00:15:0c:f1:0d:d0)
> [ 186.944090] link to new AP
> [ 186.944100] <=rtw_wx_set_essid, ret 0
> [ 186.944110] Set BSSID under fw_state=0x00000088
> [ 187.125476] link to new AP
> [ 187.125484] issue_deauth to 00:15:0c:f1:0d:d0
> [ 187.129338] OnAuthClient
> [ 187.129349] network.SupportedRates[0]=82
> [ 187.129351] network.SupportedRates[1]=84
> [ 187.129353] network.SupportedRates[2]=8B
> [ 187.129356] network.SupportedRates[3]=96
> [ 187.129358] network.SupportedRates[4]=2C
> [ 187.129360] network.SupportedRates[5]=0C
> [ 187.129362] network.SupportedRates[6]=12
> [ 187.129364] network.SupportedRates[7]=18
> [ 187.129366] network.SupportedRates[8]=24
> [ 187.129368] network.SupportedRates[9]=30
> [ 187.129370] network.SupportedRates[10]=48
> [ 187.129372] network.SupportedRates[11]=60
> [ 187.129374] network.SupportedRates[12]=6C
> [ 187.129377] issue_assocreq(): the rate[4]=2C is not supported by STA!
> [ 187.129380] bssrate_len = 12
> [ 187.135954] OnAssocRsp
> [ 187.135977] report_join_res(1)
> [ 187.135983] rtw_joinbss_update_network
> [ 187.135994] rtw_joinbss_update_stainfo
> [ 187.136060] HW_VAR_BASIC_RATE: BrateCfg(0x15d)
> [ 187.137196] HTOnAssocRsp
> [ 187.137334] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> [ 187.142408] update raid entry, mask=0x40000fff, arg=0x80
> [ 187.143905] rtl8192c_set_FwJoinBssReport_cmd mstatus(1)
> [ 187.144776] SetFwRsvdPagePkt
> [ 187.144787] Set RSVD page location to Fw.
> [ 187.145453]
> [ 187.145455] ~~~~stastakey:unicastkey
> [ 187.145524]
> [ 187.145525] ~~~~stastakey:groupkey
> [ 187.145529] ==> rtw_set_key algorithm(2),keyid(2),key_mask(4)
> [ 187.145903] =>mlmeext_joinbss_event_callback
> [ 187.811595] rx bc/mc packets, to perform sw rtw_tkip_decrypt
> [ 188.141761] rtl8192c_dm_RF_Saving(): RF_Save
> [ 197.538636] wlan0: no IPv6 routers present
> tommy@Tommy-AIO:~$ lsusb -v -d 0bda:819a
>
> Bus 001 Device 006: ID 0bda:819a Realtek Semiconductor Corp.
> Couldn't open device, some information will be missing
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> idVendor 0x0bda Realtek Semiconductor Corp.
> idProduct 0x819a
> bcdDevice 2.00
> iManufacturer 1
> iProduct 2
> iSerial 3
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 46
> bNumInterfaces 1
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0xa0
> (Bus Powered)
> Remote Wakeup
> MaxPower 500mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 4
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 255 Vendor Specific Subclass
> bInterfaceProtocol 255 Vendor Specific Protocol
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x02 EP 2 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x03 EP 3 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x84 EP 4 IN
> bmAttributes 3
> Transfer Type Interrupt
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0040 1x 64 bytes
> bInterval 1
next prev parent reply other threads:[~2013-02-05 19:55 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-04 21:41 FW: 0bda:819a RTL8188CUS WLAN doesn't work out of the box in downstream and upstreamkernel Xose Vazquez Perez
[not found] ` <CAOAX8-k-Nbx4Om8fkEHRW2jmZCxKpsMY6oEZMAvdEQpXWn9Mdw@mail.gmail.com>
2013-02-04 23:13 ` Larry Finger
2013-02-04 23:26 ` Xose Vazquez Perez
[not found] ` <CAOAX8-kFtWuwEvz9v7hBzOwtohJx0NezrDHC0iVwXF29YYSCgQ@mail.gmail.com>
2013-02-05 18:33 ` Thomas Rosenkranz
2013-02-05 19:03 ` Larry Finger
[not found] ` <CAOAX8-mMsXu5h-7q2EJEc9SehWS=yqAb4YvbfOVBQKhdH+LqTQ@mail.gmail.com>
2013-02-05 18:36 ` Fwd: " Thomas Rosenkranz
2013-02-05 19:55 ` Xose Vazquez Perez [this message]
2013-02-05 20:23 ` Larry Finger
2013-02-05 21:18 ` Thomas Rosenkranz
2013-02-05 21:28 ` Xose Vazquez Perez
2013-02-05 21:54 ` Larry Finger
2013-02-05 22:37 ` Xose Vazquez Perez
2013-02-05 23:45 ` Larry Finger
2013-02-06 0:03 ` Xose Vazquez Perez
-- strict thread matches above, loose matches on Subject: below --
2013-02-04 17:50 Thomas Rosenkranz
2013-02-04 19:49 ` Larry Finger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=511163BA.7060902@gmail.com \
--to=xose.vazquez@gmail.com \
--cc=Larry.Finger@lwfinger.net \
--cc=linux-wireless@vger.kernel.org \
--cc=tom.rosary@googlemail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).