* brcmfmac, BCM43241
@ 2013-09-11 20:35 Jan-Oliver Kaiser
2013-09-11 22:41 ` Franky Lin
2013-09-13 17:16 ` Franky Lin
0 siblings, 2 replies; 6+ messages in thread
From: Jan-Oliver Kaiser @ 2013-09-11 20:35 UTC (permalink / raw)
To: linux-wireless
Hi,
I am trying to get a BCM43241 card running on a 3.11-amd64 kernel.
[1] lists the device as supported but gives no instructions on how to
install it. I managed to extract the firmware from the git binary patch
contained in [2].
I copied the firmware to /lib/firmware/brcm/brcmfmac-sdio.bin and copied
the content of /dev/nvram to /lib/firmware/brcm/brcmfmac-sdio.txt.
Previously, `dmesg` would list error that indicated missing files.
Currently, the output is as follows:
[12865.299503] brcmfmac: brcmf_sdio_chip_drivestrengthinit: No SDIO
Drive strength init done for chip 4324 rev 5 pmurev 17
[12866.393551] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
clkctl 0x50
[12867.402386] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
clkctl 0x50
[12867.409143] brcmfmac: brcmf_proto_cdc_query_dcmd: brcmf_proto_cdc_msg
failed w/status -5
[12867.409149] brcmfmac: brcmf_fil_cmd_data: Failed err=-5
[12867.409153] brcmfmac: brcmf_c_preinit_dcmds: Retreiving cur_etheraddr
failed, -5
[12867.409157] brcmfmac: brcmf_bus_start: failed: -5
[12867.409167] brcmfmac: brcmf_sdbrcm_probe: dongle is not responding
[12868.416890] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
clkctl 0x50
[12869.426308] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
clkctl 0x50
I have not been able to find anything to help with debugging this.
There was some discussion in response to [2] that I don't understand. Is
there something wrong with the firmware itself?
I would be very grateful for any help. I can provide all additional
information if something is missing from this report. (I can also be
reached via IRC, 'Eruquen' on freenode)
Thanks in advance,
Jan-Oliver
[1] http://wireless.kernel.org/en/users/Drivers/brcm80211
[2] http://www.spinics.net/lists/linux-wireless/msg107754.html
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac, BCM43241
2013-09-11 20:35 brcmfmac, BCM43241 Jan-Oliver Kaiser
@ 2013-09-11 22:41 ` Franky Lin
2013-09-11 23:39 ` Jan-Oliver Kaiser
2013-09-13 17:16 ` Franky Lin
1 sibling, 1 reply; 6+ messages in thread
From: Franky Lin @ 2013-09-11 22:41 UTC (permalink / raw)
To: mail; +Cc: linux-wireless
Hi Jan-Oliver,
Could you please send us the full log? Also please share more details
about the hardware platform you are using. We need to figure out how to
get the nvram file.
Regards,
Franky
On 09/11/2013 01:35 PM, Jan-Oliver Kaiser wrote:
> Hi,
>
> I am trying to get a BCM43241 card running on a 3.11-amd64 kernel.
> [1] lists the device as supported but gives no instructions on how to
> install it. I managed to extract the firmware from the git binary patch
> contained in [2].
>
> I copied the firmware to /lib/firmware/brcm/brcmfmac-sdio.bin and copied
> the content of /dev/nvram to /lib/firmware/brcm/brcmfmac-sdio.txt.
>
> Previously, `dmesg` would list error that indicated missing files.
> Currently, the output is as follows:
>
> [12865.299503] brcmfmac: brcmf_sdio_chip_drivestrengthinit: No SDIO
> Drive strength init done for chip 4324 rev 5 pmurev 17
> [12866.393551] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
> clkctl 0x50
> [12867.402386] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
> clkctl 0x50
> [12867.409143] brcmfmac: brcmf_proto_cdc_query_dcmd: brcmf_proto_cdc_msg
> failed w/status -5
> [12867.409149] brcmfmac: brcmf_fil_cmd_data: Failed err=-5
> [12867.409153] brcmfmac: brcmf_c_preinit_dcmds: Retreiving cur_etheraddr
> failed, -5
> [12867.409157] brcmfmac: brcmf_bus_start: failed: -5
> [12867.409167] brcmfmac: brcmf_sdbrcm_probe: dongle is not responding
> [12868.416890] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
> clkctl 0x50
> [12869.426308] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
> clkctl 0x50
>
> I have not been able to find anything to help with debugging this.
>
> There was some discussion in response to [2] that I don't understand. Is
> there something wrong with the firmware itself?
>
> I would be very grateful for any help. I can provide all additional
> information if something is missing from this report. (I can also be
> reached via IRC, 'Eruquen' on freenode)
>
> Thanks in advance,
> Jan-Oliver
>
> [1] http://wireless.kernel.org/en/users/Drivers/brcm80211
> [2] http://www.spinics.net/lists/linux-wireless/msg107754.html
> --
> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac, BCM43241
2013-09-11 22:41 ` Franky Lin
@ 2013-09-11 23:39 ` Jan-Oliver Kaiser
2013-09-12 0:18 ` Franky Lin
0 siblings, 1 reply; 6+ messages in thread
From: Jan-Oliver Kaiser @ 2013-09-11 23:39 UTC (permalink / raw)
To: frankyl; +Cc: linux-wireless
[-- Attachment #1: Type: text/plain, Size: 3241 bytes --]
Hi Franky,
Thank you for your response. I'll attach the full dmesg output. The
device is a Sony Vaio Duo 13 laptop (SVD1321C5E).
The dmesg part I posted in the first mail is (as far as I can tell) the
only part related to the built-in wireless adapter. I have another
wireless adapter attached via USB, which is responsible for earlier
output related to wireless stuff.
The dmesg entries about brcmfmac are triggered simply by `modprobe
brmcfmac`.
Best regards,
Jan-Oliver
P.S.:
I read somewhere that the wireless adapter and the touchscreen, which is
also not working, are both connected via an Intel GPIO Controller but I
can't seem to find the source. I don't know what that means or if it is
true. Maybe somebody here can make use of this information.
On 09/12/2013 12:41 AM, Franky Lin wrote:
> Hi Jan-Oliver,
>
> Could you please send us the full log? Also please share more details
> about the hardware platform you are using. We need to figure out how to
> get the nvram file.
>
> Regards,
> Franky
>
> On 09/11/2013 01:35 PM, Jan-Oliver Kaiser wrote:
>> Hi,
>>
>> I am trying to get a BCM43241 card running on a 3.11-amd64 kernel.
>> [1] lists the device as supported but gives no instructions on how to
>> install it. I managed to extract the firmware from the git binary patch
>> contained in [2].
>>
>> I copied the firmware to /lib/firmware/brcm/brcmfmac-sdio.bin and copied
>> the content of /dev/nvram to /lib/firmware/brcm/brcmfmac-sdio.txt.
>>
>> Previously, `dmesg` would list error that indicated missing files.
>> Currently, the output is as follows:
>>
>> [12865.299503] brcmfmac: brcmf_sdio_chip_drivestrengthinit: No SDIO
>> Drive strength init done for chip 4324 rev 5 pmurev 17
>> [12866.393551] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
>> clkctl 0x50
>> [12867.402386] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
>> clkctl 0x50
>> [12867.409143] brcmfmac: brcmf_proto_cdc_query_dcmd: brcmf_proto_cdc_msg
>> failed w/status -5
>> [12867.409149] brcmfmac: brcmf_fil_cmd_data: Failed err=-5
>> [12867.409153] brcmfmac: brcmf_c_preinit_dcmds: Retreiving cur_etheraddr
>> failed, -5
>> [12867.409157] brcmfmac: brcmf_bus_start: failed: -5
>> [12867.409167] brcmfmac: brcmf_sdbrcm_probe: dongle is not responding
>> [12868.416890] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
>> clkctl 0x50
>> [12869.426308] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
>> clkctl 0x50
>>
>> I have not been able to find anything to help with debugging this.
>>
>> There was some discussion in response to [2] that I don't understand. Is
>> there something wrong with the firmware itself?
>>
>> I would be very grateful for any help. I can provide all additional
>> information if something is missing from this report. (I can also be
>> reached via IRC, 'Eruquen' on freenode)
>>
>> Thanks in advance,
>> Jan-Oliver
>>
>> [1] http://wireless.kernel.org/en/users/Drivers/brcm80211
>> [2] http://www.spinics.net/lists/linux-wireless/msg107754.html
>> --
>> To unsubscribe from this list: send the line "unsubscribe
>> linux-wireless" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>
>
[-- Attachment #2: dmesg.log --]
[-- Type: text/x-log, Size: 66429 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.11-0.slh.2-aptosid-amd64 (Debian 3.11-2) (s.l-h@gmx.de) (gcc version 4.8.1 (Debian 4.8.1-10) ) #1 SMP PREEMPT Thu Sep 5 20:56:14 UTC 2013
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.11-0.slh.2-aptosid-amd64 root=/dev/mapper/os-base ro quiet acpi_backlight=vendor
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000006efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000006f000-0x000000000006ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000070000-0x0000000000087fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000088000-0x00000000000bffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000008bc36fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000008bc37000-0x000000008d0affff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000008d0b0000-0x00000000916befff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000916bf000-0x0000000091ebefff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000091ebf000-0x0000000091fbefff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x0000000091fbf000-0x0000000091ffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x0000000091fff000-0x0000000091ffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000092000000-0x000000009f9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fe101000-0x00000000fe112fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb0ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000025f5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.31 by INSYDE Corp.
[ 0.000000] efi: ACPI=0x91ffe000 ACPI 2.0=0x91ffe014 SMBIOS=0x91ebef98
[ 0.000000] efi: mem00: type=3, attr=0xf, range=[0x0000000000000000-0x0000000000001000) (0MB)
[ 0.000000] efi: mem01: type=7, attr=0xf, range=[0x0000000000001000-0x000000000006f000) (0MB)
[ 0.000000] efi: mem02: type=0, attr=0xf, range=[0x000000000006f000-0x0000000000070000) (0MB)
[ 0.000000] efi: mem03: type=7, attr=0xf, range=[0x0000000000070000-0x0000000000088000) (0MB)
[ 0.000000] efi: mem04: type=6, attr=0x800000000000000f, range=[0x0000000000088000-0x00000000000a0000) (0MB)
[ 0.000000] efi: mem05: type=2, attr=0xf, range=[0x0000000000100000-0x0000000000c67000) (11MB)
[ 0.000000] efi: mem06: type=7, attr=0xf, range=[0x0000000000c67000-0x00000000365ae000) (857MB)
[ 0.000000] efi: mem07: type=2, attr=0xf, range=[0x00000000365ae000-0x00000000372cf000) (13MB)
[ 0.000000] efi: mem08: type=7, attr=0xf, range=[0x00000000372cf000-0x000000004cf21000) (348MB)
[ 0.000000] efi: mem09: type=2, attr=0xf, range=[0x000000004cf21000-0x000000008a0c0000) (977MB)
[ 0.000000] efi: mem10: type=4, attr=0xf, range=[0x000000008a0c0000-0x000000008a0e0000) (0MB)
[ 0.000000] efi: mem11: type=7, attr=0xf, range=[0x000000008a0e0000-0x000000008ade3000) (13MB)
[ 0.000000] efi: mem12: type=4, attr=0xf, range=[0x000000008ade3000-0x000000008bc37000) (14MB)
[ 0.000000] efi: mem13: type=0, attr=0xf, range=[0x000000008bc37000-0x000000008d0b0000) (20MB)
[ 0.000000] efi: mem14: type=7, attr=0xf, range=[0x000000008d0b0000-0x000000008d20a000) (1MB)
[ 0.000000] efi: mem15: type=1, attr=0xf, range=[0x000000008d20a000-0x000000008d2bf000) (0MB)
[ 0.000000] efi: mem16: type=7, attr=0xf, range=[0x000000008d2bf000-0x000000008de35000) (11MB)
[ 0.000000] efi: mem17: type=4, attr=0xf, range=[0x000000008de35000-0x000000008f4f6000) (22MB)
[ 0.000000] efi: mem18: type=7, attr=0xf, range=[0x000000008f4f6000-0x000000008f4f9000) (0MB)
[ 0.000000] efi: mem19: type=4, attr=0xf, range=[0x000000008f4f9000-0x000000008f508000) (0MB)
[ 0.000000] efi: mem20: type=7, attr=0xf, range=[0x000000008f508000-0x000000008f509000) (0MB)
[ 0.000000] efi: mem21: type=4, attr=0xf, range=[0x000000008f509000-0x000000008f645000) (1MB)
[ 0.000000] efi: mem22: type=7, attr=0xf, range=[0x000000008f645000-0x000000008f649000) (0MB)
[ 0.000000] efi: mem23: type=4, attr=0xf, range=[0x000000008f649000-0x000000008f661000) (0MB)
[ 0.000000] efi: mem24: type=7, attr=0xf, range=[0x000000008f661000-0x000000008f666000) (0MB)
[ 0.000000] efi: mem25: type=4, attr=0xf, range=[0x000000008f666000-0x000000008f667000) (0MB)
[ 0.000000] efi: mem26: type=7, attr=0xf, range=[0x000000008f667000-0x000000008f668000) (0MB)
[ 0.000000] efi: mem27: type=4, attr=0xf, range=[0x000000008f668000-0x000000008f66d000) (0MB)
[ 0.000000] efi: mem28: type=7, attr=0xf, range=[0x000000008f66d000-0x000000008f66e000) (0MB)
[ 0.000000] efi: mem29: type=4, attr=0xf, range=[0x000000008f66e000-0x000000008f692000) (0MB)
[ 0.000000] efi: mem30: type=7, attr=0xf, range=[0x000000008f692000-0x000000008f693000) (0MB)
[ 0.000000] efi: mem31: type=4, attr=0xf, range=[0x000000008f693000-0x000000008f696000) (0MB)
[ 0.000000] efi: mem32: type=7, attr=0xf, range=[0x000000008f696000-0x000000008f699000) (0MB)
[ 0.000000] efi: mem33: type=4, attr=0xf, range=[0x000000008f699000-0x000000008f69a000) (0MB)
[ 0.000000] efi: mem34: type=7, attr=0xf, range=[0x000000008f69a000-0x000000008f69e000) (0MB)
[ 0.000000] efi: mem35: type=4, attr=0xf, range=[0x000000008f69e000-0x00000000912bf000) (28MB)
[ 0.000000] efi: mem36: type=7, attr=0xf, range=[0x00000000912bf000-0x0000000091385000) (0MB)
[ 0.000000] efi: mem37: type=2, attr=0xf, range=[0x0000000091385000-0x000000009138e000) (0MB)
[ 0.000000] efi: mem38: type=3, attr=0xf, range=[0x000000009138e000-0x00000000916bf000) (3MB)
[ 0.000000] efi: mem39: type=5, attr=0x800000000000000f, range=[0x00000000916bf000-0x00000000918bf000) (2MB)
[ 0.000000] efi: mem40: type=6, attr=0x800000000000000f, range=[0x00000000918bf000-0x0000000091abf000) (2MB)
[ 0.000000] efi: mem41: type=0, attr=0xf, range=[0x0000000091abf000-0x0000000091ebf000) (4MB)
[ 0.000000] efi: mem42: type=10, attr=0xf, range=[0x0000000091ebf000-0x0000000091fbf000) (1MB)
[ 0.000000] efi: mem43: type=9, attr=0xf, range=[0x0000000091fbf000-0x0000000091fff000) (0MB)
[ 0.000000] efi: mem44: type=4, attr=0xf, range=[0x0000000091fff000-0x0000000092000000) (0MB)
[ 0.000000] efi: mem45: type=7, attr=0xf, range=[0x0000000100000000-0x000000025f600000) (5622MB)
[ 0.000000] efi: mem46: type=0, attr=0x0, range=[0x00000000000a0000-0x00000000000c0000) (0MB)
[ 0.000000] efi: mem47: type=0, attr=0x0, range=[0x0000000092000000-0x000000009fa00000) (218MB)
[ 0.000000] efi: mem48: type=11, attr=0x8000000000000001, range=[0x00000000e0000000-0x00000000f0000000) (256MB)
[ 0.000000] efi: mem49: type=0, attr=0x0, range=[0x00000000fe101000-0x00000000fe113000) (0MB)
[ 0.000000] efi: mem50: type=11, attr=0x8000000000000001, range=[0x00000000feb00000-0x00000000feb10000) (0MB)
[ 0.000000] efi: mem51: type=11, attr=0x8000000000000001, range=[0x00000000fec00000-0x00000000fec01000) (0MB)
[ 0.000000] efi: mem52: type=11, attr=0x8000000000000001, range=[0x00000000fed00000-0x00000000fed1c000) (0MB)
[ 0.000000] efi: mem53: type=11, attr=0x8000000000000000, range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
[ 0.000000] efi: mem54: type=11, attr=0x8000000000000001, range=[0x00000000fed20000-0x00000000fee01000) (0MB)
[ 0.000000] efi: mem55: type=11, attr=0x8000000000000000, range=[0x00000000ffc00000-0x0000000100000000) (4MB)
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: Sony Corporation SVD1321C5E/VAIO, BIOS R0150S7 05/17/2013
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x25f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E7FFF write-protect
[ 0.000000] E8000-EFFFF write-combining
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7F80000000 write-back
[ 0.000000] 1 base 0080000000 mask 7FF0000000 write-back
[ 0.000000] 2 base 0090000000 mask 7FFE000000 write-back
[ 0.000000] 3 base 00FFC00000 mask 7FFFC00000 write-protect
[ 0.000000] 4 base 0100000000 mask 7F00000000 write-back
[ 0.000000] 5 base 0200000000 mask 7F80000000 write-back
[ 0.000000] 6 base 025F600000 mask 7FFFE00000 uncachable
[ 0.000000] 7 base 025F800000 mask 7FFF800000 uncachable
[ 0.000000] 8 base 0260000000 mask 7FE0000000 uncachable
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: last_pfn = 0x92000 max_arch_pfn = 0x400000000
[ 0.000000] Base memory trampoline at [ffff88000007e000] 7e000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01745000, 0x01745fff] PGTABLE
[ 0.000000] BRK [0x01746000, 0x01746fff] PGTABLE
[ 0.000000] BRK [0x01747000, 0x01747fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x25f400000-0x25f5fffff]
[ 0.000000] [mem 0x25f400000-0x25f5fffff] page 2M
[ 0.000000] BRK [0x01748000, 0x01748fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x25c000000-0x25f3fffff]
[ 0.000000] [mem 0x25c000000-0x25f3fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x200000000-0x25bffffff]
[ 0.000000] [mem 0x200000000-0x23fffffff] page 1G
[ 0.000000] [mem 0x240000000-0x25bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x8bc36fff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0x7fffffff] page 1G
[ 0.000000] [mem 0x80000000-0x8bbfffff] page 2M
[ 0.000000] [mem 0x8bc00000-0x8bc36fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x8d0b0000-0x916befff]
[ 0.000000] [mem 0x8d0b0000-0x8d1fffff] page 4k
[ 0.000000] [mem 0x8d200000-0x915fffff] page 2M
[ 0.000000] [mem 0x91600000-0x916befff] page 4k
[ 0.000000] BRK [0x01749000, 0x01749fff] PGTABLE
[ 0.000000] BRK [0x0174a000, 0x0174afff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x91fff000-0x91ffffff]
[ 0.000000] [mem 0x91fff000-0x91ffffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x1ffffffff]
[ 0.000000] [mem 0x100000000-0x1ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x365ae000-0x372cefff]
[ 0.000000] ACPI: RSDP 0000000091ffe014 00024 (v02 Sony)
[ 0.000000] ACPI: XSDT 0000000091ffe210 000EC (v01 Sony VAIO 20130517 01000013)
[ 0.000000] ACPI: FACP 0000000091ff5000 0010C (v05 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI Error: Gpe0Block - 32-bit FADT register is too long (32 bytes, 256 bits) to convert to GAS struct - 255 bits max, truncating (20130517/tbfadt-202)
[ 0.000000] ACPI: DSDT 0000000091fe8000 09CF8 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: FACS 0000000091fb9000 00040
[ 0.000000] ACPI: UEFI 0000000091ffd000 00236 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: FPDT 0000000091ffb000 00044 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: MSDM 0000000091ffa000 00055 (v03 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091ff9000 00496 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091ff8000 0004A (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: TPM2 0000000091ff7000 00038 (v03 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: ASF! 0000000091ff6000 000A5 (v32 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: HPET 0000000091ff4000 00038 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: APIC 0000000091ff3000 0008C (v03 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: MCFG 0000000091ff2000 0003C (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091fe7000 007D9 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: BOOT 0000000091fe6000 00028 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: ASPT 0000000091fe5000 00034 (v07 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: DBGP 0000000091fe4000 00034 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091fe2000 01813 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091fe1000 00473 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091fe0000 00AD8 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091fdf000 00410 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091fdc000 02C30 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091fdb000 00379 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: PCCT 0000000091fda000 0006E (v05 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: SSDT 0000000091fd9000 00AC4 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: CSRT 0000000091fd7000 000C4 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: BGRT 0000000091fd8000 00038 (v01 Sony VAIO 20130517 ACPI 00040000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000025f5fffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x25f5fffff]
[ 0.000000] NODE_DATA [mem 0x25f5e9000-0x25f5fcfff]
[ 0.000000] [ffffea0000000000-ffffea00097fffff] PMD -> [ffff880256e00000-ffff88025ebfffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x25f5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0006efff]
[ 0.000000] node 0: [mem 0x00070000-0x00087fff]
[ 0.000000] node 0: [mem 0x00100000-0x8bc36fff]
[ 0.000000] node 0: [mem 0x8d0b0000-0x916befff]
[ 0.000000] node 0: [mem 0x91fff000-0x91ffffff]
[ 0.000000] node 0: [mem 0x100000000-0x25f5fffff]
[ 0.000000] On node 0 totalpages: 2029517
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 22 pages reserved
[ 0.000000] DMA zone: 3974 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 9162 pages used for memmap
[ 0.000000] DMA32 zone: 586311 pages, LIFO batch:31
[ 0.000000] Normal zone: 22488 pages used for memmap
[ 0.000000] Normal zone: 1439232 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 56
[ 0.000000] PM: Registered nosave memory: [mem 0x0006f000-0x0006ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00088000-0x000bffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000c0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x8bc37000-0x8d0affff]
[ 0.000000] PM: Registered nosave memory: [mem 0x916bf000-0x91ebefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x91ebf000-0x91fbefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x91fbf000-0x91ffefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x92000000-0x9f9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9fa00000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfe100fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe101000-0xfe112fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe113000-0xfeafffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb10000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffbfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xffc00000-0xffffffff]
[ 0.000000] e820: [mem 0x9fa00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88025f200000 s80384 r8192 d22016 u262144
[ 0.000000] pcpu-alloc: s80384 r8192 d22016 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1997781
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.11-0.slh.2-aptosid-amd64 root=/dev/mapper/os-base ro quiet acpi_backlight=vendor
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 7829004K/8118068K available (3514K kernel code, 582K rwdata, 1500K rodata, 972K init, 844K bss, 289064K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
[ 0.000000] NR_IRQS:16640 nr_irqs:1016 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 33030144 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration failed
[ 0.002000] tsc: PIT calibration matches HPET. 1 loops
[ 0.002000] tsc: Detected 2294.609 MHz processor
[ 0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 4589.21 BogoMIPS (lpj=2294609)
[ 0.000007] pid_max: default: 32768 minimum: 301
[ 0.000023] init_memory_mapping: [mem 0x916bf000-0x918befff]
[ 0.000025] [mem 0x916bf000-0x918befff] page 4k
[ 0.000056] init_memory_mapping: [mem 0x918bf000-0x91abefff]
[ 0.000058] [mem 0x918bf000-0x91abefff] page 4k
[ 0.030797] Security Framework initialized
[ 0.030803] SELinux: Disabled at boot.
[ 0.031508] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.033844] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.034830] Mount-cache hash table entries: 256
[ 0.035052] Initializing cgroup subsys memory
[ 0.035061] Initializing cgroup subsys devices
[ 0.035064] Initializing cgroup subsys freezer
[ 0.035066] Initializing cgroup subsys net_cls
[ 0.035067] Initializing cgroup subsys blkio
[ 0.035069] Initializing cgroup subsys perf_event
[ 0.035098] CPU: Physical Processor ID: 0
[ 0.035099] CPU: Processor Core ID: 0
[ 0.035106] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.035106] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.036406] mce: CPU supports 7 MCE banks
[ 0.036423] CPU0: Thermal monitoring enabled (TM1)
[ 0.036438] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.036438] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0
[ 0.036438] tlb_flushall_shift: 6
[ 0.036559] Freeing SMP alternatives memory: 8K (ffffffff8166e000 - ffffffff81670000)
[ 0.036971] ACPI: Core revision 20130517
[ 0.050345] ACPI: All ACPI Tables successfully acquired
[ 0.056536] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.066535] smpboot: CPU0: Intel(R) Core(TM) i5-4200U CPU @ 1.60GHz (fam: 06, model: 45, stepping: 01)
[ 0.066545] TSC deadline timer enabled
[ 0.066558] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.066568] ... version: 3
[ 0.066569] ... bit width: 48
[ 0.066571] ... generic registers: 4
[ 0.066573] ... value mask: 0000ffffffffffff
[ 0.066574] ... max period: 0000ffffffffffff
[ 0.066576] ... fixed-purpose events: 3
[ 0.066577] ... event mask: 000000070000000f
[ 0.074687] smpboot: Booting Node 0, Processors #1 #2 #3
[ 0.122553] Brought up 4 CPUs
[ 0.122557] smpboot: Total of 4 processors activated (18356.87 BogoMIPS)
[ 0.127850] devtmpfs: initialized
[ 0.131543] PM: Registering ACPI NVS region [mem 0x91ebf000-0x91fbefff] (1048576 bytes)
[ 0.131687] NET: Registered protocol family 16
[ 0.131837] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.131839] ACPI: bus type PCI registered
[ 0.131842] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.131914] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.131917] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.146094] PCI: Using configuration type 1 for base access
[ 0.146925] bio: create slab <bio-0> at 0
[ 0.147048] ACPI: Added _OSI(Module Device)
[ 0.147051] ACPI: Added _OSI(Processor Device)
[ 0.147053] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.147055] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.149803] ACPI: EC: Look up EC in DSDT
[ 0.152667] ACPI: Executed 2 blocks of module-level executable AML code
[ 0.157722] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.259463] ACPI: SSDT 0000000091e86c18 003D3 (v01 Sony VAIO 20130517 INTL 20120913)
[ 0.260154] ACPI: Dynamic OEM Table Load:
[ 0.260157] ACPI: SSDT (null) 003D3 (v01 Sony VAIO 20130517 INTL 20120913)
[ 0.266211] ACPI: SSDT 0000000091e86618 005AA (v01 Sony VAIO 20130517 INTL 20120913)
[ 0.266999] ACPI: Dynamic OEM Table Load:
[ 0.267002] ACPI: SSDT (null) 005AA (v01 Sony VAIO 20130517 INTL 20120913)
[ 0.272031] ACPI: SSDT 0000000091e7ed98 00119 (v01 Sony VAIO 20130517 INTL 20120913)
[ 0.272710] ACPI: Dynamic OEM Table Load:
[ 0.272713] ACPI: SSDT (null) 00119 (v01 Sony VAIO 20130517 INTL 20120913)
[ 0.279724] ACPI: Interpreter enabled
[ 0.279739] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130517/hwxface-571)
[ 0.279748] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130517/hwxface-571)
[ 0.279774] ACPI: (supports S0 S3 S4 S5)
[ 0.279776] ACPI: Using IOAPIC for interrupt routing
[ 0.279817] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.280004] ACPI: No dock devices found.
[ 0.284546] ACPI: Power Resource [PX03] (on)
[ 0.301056] ACPI: Power Resource [PX05] (on)
[ 0.317241] ACPI: Power Resource [PAUD] (on)
[ 0.317827] ACPI: Power Resource [PSEN] (on)
[ 0.317902] ACPI: Power Resource [PXTC] (on)
[ 0.345434] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[ 0.346000] PCI host bridge to bus 0000:00
[ 0.346005] pci_bus 0000:00: root bus resource [bus 00-fe]
[ 0.346008] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.346011] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.346013] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.346016] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff]
[ 0.346019] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff]
[ 0.346021] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff]
[ 0.346023] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff]
[ 0.346026] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[ 0.346028] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 0.346031] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 0.346036] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 0.346038] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[ 0.346040] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[ 0.346043] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff]
[ 0.346045] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff]
[ 0.346048] pci_bus 0000:00: root bus resource [mem 0x000f0000-0x000fffff]
[ 0.346050] pci_bus 0000:00: root bus resource [mem 0x9fa00000-0xfeafffff]
[ 0.346062] pci 0000:00:00.0: [8086:0a04] type 00 class 0x060000
[ 0.346191] pci 0000:00:02.0: [8086:0a16] type 00 class 0x030000
[ 0.346208] pci 0000:00:02.0: reg 0x10: [mem 0xb0000000-0xb03fffff 64bit]
[ 0.346218] pci 0000:00:02.0: reg 0x18: [mem 0xa0000000-0xafffffff 64bit pref]
[ 0.346225] pci 0000:00:02.0: reg 0x20: [io 0x3000-0x303f]
[ 0.346337] pci 0000:00:03.0: [8086:0a0c] type 00 class 0x040300
[ 0.346349] pci 0000:00:03.0: reg 0x10: [mem 0xb0410000-0xb0413fff 64bit]
[ 0.346522] pci 0000:00:14.0: [8086:9c31] type 00 class 0x0c0330
[ 0.346571] pci 0000:00:14.0: reg 0x10: [mem 0xb0400000-0xb040ffff 64bit]
[ 0.346735] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.346806] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.346863] pci 0000:00:16.0: [8086:9c3a] type 00 class 0x078000
[ 0.346912] pci 0000:00:16.0: reg 0x10: [mem 0xb041a000-0xb041a01f 64bit]
[ 0.347079] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.347232] pci 0000:00:1b.0: [8086:9c20] type 00 class 0x040300
[ 0.347269] pci 0000:00:1b.0: reg 0x10: [mem 0xb0414000-0xb0417fff 64bit]
[ 0.347446] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.347524] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.347580] pci 0000:00:1f.0: [8086:9c43] type 00 class 0x060100
[ 0.347919] pci 0000:00:1f.2: [8086:9c03] type 00 class 0x010601
[ 0.347963] pci 0000:00:1f.2: reg 0x10: [io 0x3088-0x308f]
[ 0.347982] pci 0000:00:1f.2: reg 0x14: [io 0x3094-0x3097]
[ 0.348001] pci 0000:00:1f.2: reg 0x18: [io 0x3080-0x3087]
[ 0.348020] pci 0000:00:1f.2: reg 0x1c: [io 0x3090-0x3093]
[ 0.348040] pci 0000:00:1f.2: reg 0x20: [io 0x3060-0x307f]
[ 0.348059] pci 0000:00:1f.2: reg 0x24: [mem 0xb041d000-0xb041d7ff]
[ 0.348171] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.348277] pci 0000:00:1f.3: [8086:9c22] type 00 class 0x0c0500
[ 0.348314] pci 0000:00:1f.3: reg 0x10: [mem 0xb041b000-0xb041b0ff 64bit]
[ 0.348368] pci 0000:00:1f.3: reg 0x20: [io 0x3040-0x305f]
[ 0.348603] acpi PNP0A08:00: Requesting ACPI _OSC control (0x1d)
[ 0.348846] acpi PNP0A08:00: ACPI _OSC control (0x1d) granted
[ 0.361457] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.361527] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.361593] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.361658] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.361723] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.361787] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.361852] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.361916] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.362532] ACPI: Enabled 4 GPEs in block 00 to 7F
[ 0.362542] ACPI: \_SB_.PCI0: notify handler is installed
[ 0.362628] Found 1 acpi root devices
[ 0.362680] ACPI: EC: GPE = 0xa, I/O: command/status = 0x66, data = 0x62
[ 0.362801] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.362805] vgaarb: loaded
[ 0.362807] vgaarb: bridge control possible 0000:00:02.0
[ 0.362872] PCI: Using ACPI for IRQ routing
[ 0.382054] PCI: pci_cache_line_size set to 64 bytes
[ 0.382102] e820: reserve RAM buffer [mem 0x0006f000-0x0006ffff]
[ 0.382104] e820: reserve RAM buffer [mem 0x00088000-0x0008ffff]
[ 0.382106] e820: reserve RAM buffer [mem 0x8bc37000-0x8bffffff]
[ 0.382108] e820: reserve RAM buffer [mem 0x916bf000-0x93ffffff]
[ 0.382110] e820: reserve RAM buffer [mem 0x92000000-0x93ffffff]
[ 0.382113] e820: reserve RAM buffer [mem 0x25f600000-0x25fffffff]
[ 0.382223] NetLabel: Initializing
[ 0.382225] NetLabel: domain hash size = 128
[ 0.382227] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.382237] NetLabel: unlabeled traffic allowed by default
[ 0.382298] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.382305] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.384343] Switched to clocksource hpet
[ 0.384388] pnp: PnP ACPI init
[ 0.384397] ACPI: bus type PNP registered
[ 0.384489] pnp 00:00: [dma 4]
[ 0.384511] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.384536] pnp 00:01: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.384651] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.384699] system 00:03: [io 0x0680-0x069f] has been reserved
[ 0.384702] system 00:03: [io 0xffff] has been reserved
[ 0.384705] system 00:03: [io 0xffff] has been reserved
[ 0.384707] system 00:03: [io 0xffff] has been reserved
[ 0.384712] system 00:03: [io 0x0400-0x0453] has been reserved
[ 0.384715] system 00:03: [io 0x0800-0x08fe] has been reserved
[ 0.384718] system 00:03: [io 0x0900-0x09fe] has been reserved
[ 0.384720] system 00:03: [io 0x0a00-0x0afe] has been reserved
[ 0.384725] system 00:03: [io 0x0b00-0x0bfe] has been reserved
[ 0.384728] system 00:03: [io 0x1800-0x18fe] could not be reserved
[ 0.384730] system 00:03: [io 0x164e-0x164f] has been reserved
[ 0.384733] system 00:03: [io 0x2000] has been reserved
[ 0.384736] system 00:03: [io 0x2004] has been reserved
[ 0.384739] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.384770] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.384820] system 00:05: [io 0x1854-0x1857] has been reserved
[ 0.384824] system 00:05: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.384874] pnp 00:06: Plug and Play ACPI device, IDs SNYa009 PNP030b (active)
[ 0.385039] system 00:07: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.385042] system 00:07: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.385045] system 00:07: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.385047] system 00:07: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.385050] system 00:07: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.385053] system 00:07: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.385056] system 00:07: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.385059] system 00:07: [mem 0xff000000-0xffffffff] could not be reserved
[ 0.385062] system 00:07: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.385065] system 00:07: [mem 0x9fa10000-0x9fa10fff] has been reserved
[ 0.385068] system 00:07: [mem 0xffffffff-0x100000ffe] could not be reserved
[ 0.385071] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.395447] system 00:08: [mem 0xb0425000-0xb0425fff] has been reserved
[ 0.395452] system 00:08: [mem 0xfe104000-0xfe104fff] has been reserved
[ 0.395455] system 00:08: [mem 0xfe106000-0xfe106fff] has been reserved
[ 0.395458] system 00:08: [mem 0xb041f000-0xb041ffff] has been reserved
[ 0.395461] system 00:08: [mem 0xb041e000-0xb041efff] has been reserved
[ 0.395464] system 00:08: [mem 0xb0419000-0xb0419007] has been reserved
[ 0.395466] system 00:08: [mem 0xb0419014-0xb0419fff] has been reserved
[ 0.395470] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.395706] pnp 00:09: unknown resource type 19 in _CRS
[ 0.395709] pnp 00:09: can't evaluate _CRS: 1
[ 0.395738] pnp 00:09: Plug and Play ACPI device, IDs INT33d1 PNP0c50 (active)
[ 0.395842] pnp 00:0a: unknown resource type 19 in _CRS
[ 0.395844] pnp 00:0a: can't evaluate _CRS: 1
[ 0.395876] pnp 00:0a: Plug and Play ACPI device, IDs PNP0c50 (active)
[ 0.395939] pnp 00:0b: unknown resource type 19 in _CRS
[ 0.395942] pnp 00:0b: can't evaluate _CRS: 1
[ 0.395971] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c50 (active)
[ 0.396128] pnp 00:0c: unknown resource type 19 in _CRS
[ 0.396130] pnp 00:0c: can't evaluate _CRS: 1
[ 0.396155] pnp 00:0c: Plug and Play ACPI device, IDs BCM2e47 (active)
[ 0.396573] pnp: PnP ACPI: found 13 devices
[ 0.396575] ACPI: bus type PNP unregistered
[ 0.403988] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.403991] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.403994] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.403997] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.403999] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.404002] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.404004] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff]
[ 0.404007] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.404009] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.404012] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.404014] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.404017] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.404019] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.404022] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff]
[ 0.404024] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff]
[ 0.404026] pci_bus 0000:00: resource 19 [mem 0x000f0000-0x000fffff]
[ 0.404029] pci_bus 0000:00: resource 20 [mem 0x9fa00000-0xfeafffff]
[ 0.404063] NET: Registered protocol family 2
[ 0.404360] TCP established hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.404615] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.404773] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.404798] TCP: reno registered
[ 0.404815] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.404852] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.404942] NET: Registered protocol family 1
[ 0.404959] pci 0000:00:02.0: Boot video device
[ 0.406787] PCI: CLS 64 bytes, default 64
[ 0.406834] Unpacking initramfs...
[ 0.782864] Freeing initrd memory: 13444K (ffff8800365ae000 - ffff8800372cf000)
[ 0.782871] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.782874] software IO TLB [mem 0x860c0000-0x8a0c0000] (64MB) mapped at [ffff8800860c0000-ffff88008a0bffff]
[ 0.782934] Simple Boot Flag at 0x44 set to 0x1
[ 0.783146] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x10
[ 0.783156] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x10
[ 0.783167] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x10
[ 0.783178] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x10
[ 0.783278] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 0.783547] audit: initializing netlink socket (disabled)
[ 0.783558] type=2000 audit(1378915826.761:1): initialized
[ 0.784072] bounce pool size: 64 pages
[ 0.784085] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.785843] zbud: loaded
[ 0.786026] VFS: Disk quotas dquot_6.5.2
[ 0.786076] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.786210] msgmni has been set to 15457
[ 0.786753] alg: No test for stdrng (krng)
[ 0.786765] Key type asymmetric registered
[ 0.786769] Asymmetric key parser 'x509' registered
[ 0.786807] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.786869] io scheduler noop registered
[ 0.786871] io scheduler deadline registered
[ 0.786882] io scheduler cfq registered (default)
[ 0.786944] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.786960] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.787039] efifb: probing for efifb
[ 0.787618] efifb: framebuffer at 0xa0000000, mapped to 0xffffc90021500000, using 8128k, total 8128k
[ 0.787621] efifb: mode is 1920x1080x32, linelength=7680, pages=1
[ 0.787622] efifb: scrolling: redraw
[ 0.787625] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.795351] Console: switching to colour frame buffer device 240x67
[ 0.802918] fb0: EFI VGA frame buffer device
[ 0.802926] intel_idle: MWAIT substates: 0x11142120
[ 0.802928] intel_idle: v0.4 model 0x45
[ 0.802929] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.802997] GHES: HEST is not enabled!
[ 0.803066] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.803821] Linux agpgart interface v0.103
[ 0.803892] libphy: Fixed MDIO Bus: probed
[ 0.803937] i8042: PNP: PS/2 Controller [PNP030b:PS2K] at 0x60,0x64 irq 1
[ 0.803939] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.804912] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.805007] mousedev: PS/2 mouse device common for all mice
[ 0.805069] rtc_cmos 00:04: RTC can wake from S4
[ 0.805340] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.805398] rtc_cmos 00:04: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.805567] cpuidle: using governor ladder
[ 0.805788] cpuidle: using governor menu
[ 0.805950] EFI Variables Facility v0.08 2004-May-17
[ 0.824001] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.840483] TCP: cubic registered
[ 0.840600] NET: Registered protocol family 10
[ 0.840842] Key type dns_resolver registered
[ 0.841435] registered taskstats version 1
[ 0.841725] IMA: No TPM chip found, activating TPM-bypass!
[ 0.842346] rtc_cmos 00:04: setting system clock to 2013-09-11 16:10:27 UTC (1378915827)
[ 0.843222] Freeing unused kernel memory: 972K (ffffffff8157b000 - ffffffff8166e000)
[ 0.918723] udevd[73]: starting version 175
[ 0.954566] ACPI: bus type USB registered
[ 0.954610] usbcore: registered new interface driver usbfs
[ 0.954627] usbcore: registered new interface driver hub
[ 0.957324] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.957331] ACPI: Thermal Zone [TZ01] (49 C)
[ 0.958164] thermal LNXTHERM:01: registered as thermal_zone1
[ 0.958169] ACPI: Thermal Zone [TZ02] (51 C)
[ 0.958305] SCSI subsystem initialized
[ 0.960000] ACPI: bus type ATA registered
[ 0.961703] usbcore: registered new device driver usb
[ 0.962552] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 0.962561] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.962574] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 0.962781] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 0.962826] xhci_hcd 0000:00:14.0: irq 56 for MSI/MSI-X
[ 0.962940] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.962945] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.962949] usb usb1: Product: xHCI Host Controller
[ 0.962953] usb usb1: Manufacturer: Linux 3.11-0.slh.2-aptosid-amd64 xhci_hcd
[ 0.962957] usb usb1: SerialNumber: 0000:00:14.0
[ 0.964005] xHCI xhci_add_endpoint called for root hub
[ 0.964010] xHCI xhci_check_bandwidth called for root hub
[ 0.964098] hub 1-0:1.0: USB hub found
[ 0.964126] hub 1-0:1.0: 9 ports detected
[ 0.968110] libata version 3.00 loaded.
[ 0.977813] sdhci: Secure Digital Host Controller Interface driver
[ 0.977819] sdhci: Copyright(c) Pierre Ossman
[ 0.979104] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.979114] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 0.979173] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.979178] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.979182] usb usb2: Product: xHCI Host Controller
[ 0.979186] usb usb2: Manufacturer: Linux 3.11-0.slh.2-aptosid-amd64 xhci_hcd
[ 0.979189] usb usb2: SerialNumber: 0000:00:14.0
[ 0.982343] xHCI xhci_add_endpoint called for root hub
[ 0.982349] xHCI xhci_check_bandwidth called for root hub
[ 0.982401] hub 2-0:1.0: USB hub found
[ 0.982420] hub 2-0:1.0: 4 ports detected
[ 0.994965] ahci 0000:00:1f.2: version 3.0
[ 0.995253] ahci 0000:00:1f.2: irq 57 for MSI/MSI-X
[ 0.995371] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x1 impl SATA mode
[ 0.995378] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo only pio slum part deso sadm sds apst
[ 0.995388] ahci 0000:00:1f.2: setting latency timer to 64
[ 0.996241] scsi0 : ahci
[ 0.996364] scsi1 : ahci
[ 0.996460] scsi2 : ahci
[ 0.996558] scsi3 : ahci
[ 0.996659] ata1: SATA max UDMA/133 abar m2048@0xb041d000 port 0xb041d100 irq 57
[ 0.996663] ata2: DUMMY
[ 0.996666] ata3: DUMMY
[ 0.996668] ata4: DUMMY
[ 0.999061] mmc0: SDHCI controller on ACPI [INT33C6:00] using ADMA
[ 1.000689] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.000836] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[ 1.008074] alg: No test for crc32 (crc32-pclmul)
[ 1.062656] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.140436] mmc0: new high speed SDIO card at address 0001
[ 1.300972] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.303823] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.303937] ata1.00: ACPI cmd ef/10:09:00:00:00:a0 (SET FEATURES) succeeded
[ 1.304264] ata1.00: ATA-9: SAMSUNG MZNTD256HAGL-00000, DXT2300Q, max UDMA/133
[ 1.304269] ata1.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.304742] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.304814] ata1.00: ACPI cmd ef/10:09:00:00:00:a0 (SET FEATURES) succeeded
[ 1.305337] ata1.00: configured for UDMA/133
[ 1.305623] scsi 0:0:0:0: Direct-Access ATA SAMSUNG MZNTD256 DXT2 PQ: 0 ANSI: 5
[ 1.309933] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 1.310054] sd 0:0:0:0: [sda] Write Protect is off
[ 1.310060] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.310159] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.312681] sda: sda1 sda2 sda3 sda4
[ 1.313614] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.315610] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.331867] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 1.360947] usb 1-1: New USB device found, idVendor=148f, idProduct=3070
[ 1.360954] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.360957] usb 1-1: Product: 802.11 n WLAN
[ 1.360961] usb 1-1: Manufacturer: Ralink
[ 1.360963] usb 1-1: SerialNumber: 1.0
[ 1.375175] device-mapper: uevent: version 1.0.3
[ 1.375269] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: dm-devel@redhat.com
[ 1.393327] bio: create slab <bio-1> at 1
[ 1.427797] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 1.515769] usb 1-2: new high-speed USB device number 3 using xhci_hcd
[ 1.528373] usb 1-2: New USB device found, idVendor=1307, idProduct=0165
[ 1.528381] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.528385] usb 1-2: Product: USB Mass Storage Device
[ 1.528389] usb 1-2: Manufacturer: USBest Technology
[ 1.528392] usb 1-2: SerialNumber: 00000000001516
[ 1.592707] udevd[435]: starting version 175
[ 1.658992] ACPI: Requesting acpi_cpufreq
[ 1.669681] ACPI: AC Adapter [ADP1] (on-line)
[ 1.681060] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.681075] ACPI: Power Button [PWRB]
[ 1.681696] usb 1-3: new high-speed USB device number 4 using xhci_hcd
[ 1.697062] [drm] Initialized drm 1.1.0 20060810
[ 1.697377] ACPI Warning: 0x0000000000003040-0x000000000000305f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20130517/utaddress-251)
[ 1.697399] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.698151] ACPI Warning: 0x0000000000001828-0x000000000000182f SystemIO conflicts with Region \PMIO 1 (20130517/utaddress-251)
[ 1.698172] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.698183] ACPI Warning: 0x0000000000000830-0x000000000000083f SystemIO conflicts with Region \GPRL 1 (20130517/utaddress-251)
[ 1.698196] ACPI Warning: 0x0000000000000830-0x000000000000083f SystemIO conflicts with Region \GPR_ 2 (20130517/utaddress-251)
[ 1.698207] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.698213] ACPI Warning: 0x0000000000000800-0x000000000000082f SystemIO conflicts with Region \GPRL 1 (20130517/utaddress-251)
[ 1.698223] ACPI Warning: 0x0000000000000800-0x000000000000082f SystemIO conflicts with Region \GPR_ 2 (20130517/utaddress-251)
[ 1.698234] ACPI Warning: 0x0000000000000800-0x000000000000082f SystemIO conflicts with Region \IO_D 3 (20130517/utaddress-251)
[ 1.698246] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 1.698251] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 1.714519] mei_me 0000:00:16.0: setting latency timer to 64
[ 1.714683] mei_me 0000:00:16.0: irq 58 for MSI/MSI-X
[ 1.733478] mei_me 0000:00:16.0: NFC MEI VERSION: IVN 0x1 Vendor ID 0x1 Type 0x1
[ 1.783624] tsc: Refined TSC clocksource calibration: 2294.687 MHz
[ 1.785444] usb 1-3: New USB device found, idVendor=0bda, idProduct=5722
[ 1.785458] usb 1-3: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 1.785467] usb 1-3: Product: Front Camera
[ 1.785474] usb 1-3: Manufacturer: 1458700110E5694S
[ 1.785481] usb 1-3: SerialNumber: 200901010001
[ 1.796945] [drm] Memory usable by graphics device = 2048M
[ 1.796959] checking generic (a0000000 7f0000) vs hw (a0000000 10000000)
[ 1.796965] fb: conflicting fb hw usage inteldrmfb vs EFI VGA - removing generic driver
[ 1.797023] Console: switching to colour dummy device 80x25
[ 1.800060] sony_laptop: Sony Notebook Control Driver v0.6
[ 1.800350] input: Sony Vaio Keys as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/SNY5001:00/input/input2
[ 1.800475] input: Sony Vaio Jogdial as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/SNY5001:00/input/input3
[ 1.801292] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 1.811724] ACPI: Battery Slot [BAT1] (battery present)
[ 1.813848] i915 0000:00:02.0: setting latency timer to 64
[ 1.870364] i915 0000:00:02.0: irq 59 for MSI/MSI-X
[ 1.870397] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 1.870402] [drm] Driver supports precise vblank timestamp query.
[ 1.870627] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 1.877204] iTCO_vendor_support: vendor-support=0
[ 1.877973] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 1.878041] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
[ 1.886702] nfc: nfc_init: NFC Core ver 0.1
[ 1.886792] NET: Registered protocol family 39
[ 1.895848] Probing NFC pn544
[ 1.922737] fbcon: inteldrmfb (fb0) is primary device
[ 1.944580] usb 1-4: new high-speed USB device number 5 using xhci_hcd
[ 1.958150] usb 1-4: New USB device found, idVendor=12d1, idProduct=1570
[ 1.958155] usb 1-4: New USB device strings: Mfr=5, Product=4, SerialNumber=0
[ 1.958158] usb 1-4: Product: HUAWEI Mobile Broadband Module
[ 1.958161] usb 1-4: Manufacturer: Huawei Technologies Co., Ltd.
[ 1.984907] media: Linux media interface: v0.10
[ 1.987263] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 1.987425] scsi4 : usb-storage 1-2:1.0
[ 1.987696] usbcore: registered new interface driver usb-storage
[ 1.989255] usbcore: registered new interface driver usbserial
[ 1.989289] usbcore: registered new interface driver usbserial_generic
[ 1.989314] usbserial: USB Serial support registered for generic
[ 1.993947] Linux video capture interface: v2.00
[ 1.999907] cfg80211: Calling CRDA to update world regulatory domain
[ 2.000484] usbcore: registered new interface driver option
[ 2.000518] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.000672] option 1-4:1.0: GSM modem (1-port) converter detected
[ 2.000938] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB0
[ 2.000995] option 1-4:1.1: GSM modem (1-port) converter detected
[ 2.001163] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB1
[ 2.001207] option 1-4:1.2: GSM modem (1-port) converter detected
[ 2.001356] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB2
[ 2.001496] option 1-4:1.5: GSM modem (1-port) converter detected
[ 2.001648] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB3
[ 2.015187] uvcvideo: Found UVC 1.00 device Front Camera (0bda:5722)
[ 2.026805] input: Front Camera as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/input/input5
[ 2.027096] usbcore: registered new interface driver uvcvideo
[ 2.027098] USB Video Class driver (1.1.1)
[ 2.062889] usb 2-4: new SuperSpeed USB device number 2 using xhci_hcd
[ 2.163388] usb 2-4: New USB device found, idVendor=0bda, idProduct=58df
[ 2.163393] usb 2-4: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 2.163396] usb 2-4: Product: Rear Camera
[ 2.163399] usb 2-4: Manufacturer: Generic
[ 2.163402] usb 2-4: SerialNumber: 200901010001
[ 2.181739] uvcvideo: Found UVC 1.00 device Rear Camera (0bda:58df)
[ 2.190316] input: Rear Camera as /devices/pci0000:00/0000:00:14.0/usb2/2-4/2-4:1.0/input/input6
[ 2.228829] usb 1-1: reset high-speed USB device number 2 using xhci_hcd
[ 2.250922] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024f8f5240
[ 2.250927] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024f8f5200
[ 2.250930] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024f8f5280
[ 2.250934] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024f8f52c0
[ 2.250937] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024f8f5300
[ 2.250941] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024f8f5340
[ 2.250944] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88024f8f5380
[ 2.252025] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 2.267131] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 2.276125] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 2.276891] usbcore: registered new interface driver rt2800usb
[ 2.783551] Switched to clocksource tsc
[ 2.989850] scsi 4:0:0:0: Direct-Access Ut165 USB2FlashStorage 0.00 PQ: 0 ANSI: 2
[ 2.990409] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 2.990816] sd 4:0:0:0: [sdb] 31588352 512-byte logical blocks: (16.1 GB/15.0 GiB)
[ 2.991169] sd 4:0:0:0: [sdb] Write Protect is off
[ 2.991174] sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 2.991553] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 2.991558] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 2.993916] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 2.993919] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 3.134557] sdb: sdb1
[ 3.136477] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 3.136481] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 3.136487] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 3.391738] Console: switching to colour frame buffer device 240x67
[ 3.421160] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 3.421167] i915 0000:00:02.0: registered panic notifier
[ 3.436846] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 3.437019] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input7
[ 3.437213] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 3.437507] INT33C5:00: ttyS0 at MMIO 0xb0420000 (irq = 13) is a 16550A
[ 3.444075] snd_hda_intel 0000:00:03.0: irq 60 for MSI/MSI-X
[ 3.444842] snd_hda_intel 0000:00:1b.0: irq 61 for MSI/MSI-X
[ 3.455836] ALSA hda_codec.c:570 hda_codec: invalid CONNECT_LIST verb 5[1]:0
[ 3.455918] ALSA hda_codec.c:570 hda_codec: invalid CONNECT_LIST verb 6[1]:0
[ 3.455997] ALSA hda_codec.c:570 hda_codec: invalid CONNECT_LIST verb 7[1]:0
[ 3.459500] input: HDA Intel MID HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input8
[ 3.459740] input: HDA Intel MID HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
[ 3.459919] input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input10
[ 3.460971] hda_codec: ALC282: SKU not ready 0x411111f0
[ 3.477785] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
[ 3.478014] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input12
[ 3.722621] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 4.244851] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 4.492835] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[ 4.790386] fuse init (API version 7.22)
[ 12.664830] sha256_ssse3: Using AVX2 optimized SHA-256 implementation
[ 13.227265] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 13.278131] kjournald starting. Commit interval 5 seconds
[ 13.278300] EXT3-fs (dm-1): using internal journal
[ 13.278310] EXT3-fs (dm-1): mounted filesystem with writeback data mode
[ 13.298636] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 13.300938] XFS (dm-2): Mounting Filesystem
[ 13.464055] XFS (dm-2): Ending clean mount
[ 13.485641] XFS (dm-3): Mounting Filesystem
[ 13.506267] XFS (dm-3): Ending clean mount
[ 13.525544] XFS (dm-6): Mounting Filesystem
[ 13.567961] XFS (dm-6): Ending clean mount
[ 14.383202] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 14.383832] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[ 14.533064] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 14.540920] NET: Registered protocol family 17
[ 14.810420] lp: driver loaded but no devices found
[ 14.822534] ppdev: user-space parallel port driver
[ 14.994045] Bluetooth: Core ver 2.16
[ 14.994075] NET: Registered protocol family 31
[ 14.994079] Bluetooth: HCI device and connection manager initialized
[ 14.994093] Bluetooth: HCI socket layer initialized
[ 14.994100] Bluetooth: L2CAP socket layer initialized
[ 14.994112] Bluetooth: SCO socket layer initialized
[ 15.002398] Bluetooth: RFCOMM TTY layer initialized
[ 15.002429] Bluetooth: RFCOMM socket layer initialized
[ 15.002435] Bluetooth: RFCOMM ver 1.11
[ 15.003830] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 15.003838] Bluetooth: BNEP filters: protocol multicast
[ 15.003856] Bluetooth: BNEP socket layer initialized
[ 1964.925090] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1965.891651] ieee80211 phy0: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 11 in queue 0
[ 1965.891688] ieee80211 phy0: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 11 in queue 0
[ 1965.891694] ieee80211 phy0: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 11 in queue 0
[ 1970.424080] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1971.418582] ieee80211 phy0: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 11 in queue 0
[ 1971.418623] ieee80211 phy0: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 11 in queue 0
[ 1971.418630] ieee80211 phy0: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 11 in queue 0
[ 1971.596362] wlan0: authenticate with 00:1f:1f:5a:a1:30
[ 1971.620326] wlan0: send auth to 00:1f:1f:5a:a1:30 (try 1/3)
[ 1971.722227] wlan0: send auth to 00:1f:1f:5a:a1:30 (try 2/3)
[ 1971.824268] wlan0: send auth to 00:1f:1f:5a:a1:30 (try 3/3)
[ 1971.926190] wlan0: authentication with 00:1f:1f:5a:a1:30 timed out
[ 2309.960008] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2315.822103] usb 1-1: USB disconnect, device number 2
[ 2318.339414] usb 1-1: new high-speed USB device number 6 using xhci_hcd
[ 2318.369118] usb 1-1: New USB device found, idVendor=148f, idProduct=3070
[ 2318.369129] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2318.369135] usb 1-1: Product: 802.11 n WLAN
[ 2318.369139] usb 1-1: Manufacturer: Ralink
[ 2318.369143] usb 1-1: SerialNumber: 1.0
[ 2318.524672] usb 1-1: reset high-speed USB device number 6 using xhci_hcd
[ 2318.546787] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880250471e40
[ 2318.546799] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880250471e00
[ 2318.546804] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880250471e80
[ 2318.546810] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880250471ec0
[ 2318.546815] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880250471f00
[ 2318.546820] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880250471f40
[ 2318.546825] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880250471f80
[ 2318.547796] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 2318.560765] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 2318.561101] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 2318.645118] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 2318.645188] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[ 2318.786354] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2319.953635] wlan0: authenticate with 00:1f:1f:5a:a1:30
[ 2319.978642] wlan0: send auth to 00:1f:1f:5a:a1:30 (try 1/3)
[ 2319.980163] wlan0: authenticated
[ 2319.980306] rt2800usb 1-1:1.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 2319.980313] rt2800usb 1-1:1.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 2319.980386] wlan0: associate with 00:1f:1f:5a:a1:30 (try 1/3)
[ 2319.994660] wlan0: RX AssocResp from 00:1f:1f:5a:a1:30 (capab=0x411 status=0 aid=194)
[ 2319.994673] wlan0: invalid AID value 0xc2; bits 15:14 not set
[ 2319.999527] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2319.999655] wlan0: associated
[ 2320.417839] wlan0: deauthenticating from 00:1f:1f:5a:a1:30 by local choice (reason=3)
[ 2320.466125] cfg80211: Calling CRDA to update world regulatory domain
[ 2320.478040] cfg80211: World regulatory domain updated:
[ 2320.478074] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2320.478084] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2320.478090] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2320.478096] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 2320.478102] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2320.478114] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2327.191895] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2334.019872] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2334.920204] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 0
[ 2334.920245] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 0
[ 2334.920251] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 0
[ 2339.368892] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2340.544115] wlan0: authenticate with 00:1f:1f:5a:a1:30
[ 2340.556515] wlan0: send auth to 00:1f:1f:5a:a1:30 (try 1/3)
[ 2340.558035] wlan0: authenticated
[ 2340.558286] rt2800usb 1-1:1.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 2340.558294] rt2800usb 1-1:1.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 2340.558963] wlan0: associate with 00:1f:1f:5a:a1:30 (try 1/3)
[ 2340.572491] wlan0: RX AssocResp from 00:1f:1f:5a:a1:30 (capab=0x411 status=0 aid=194)
[ 2340.572504] wlan0: invalid AID value 0xc2; bits 15:14 not set
[ 2340.577074] wlan0: associated
[ 2340.577135] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[12736.244166] wlan0: deauthenticating from 00:1f:1f:5a:a1:30 by local choice (reason=3)
[12736.295140] cfg80211: Calling CRDA to update world regulatory domain
[12736.303750] cfg80211: World regulatory domain updated:
[12736.303757] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[12736.303763] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[12736.303768] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[12736.303772] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[12736.303776] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[12736.303779] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[12737.878130] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[12743.710943] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[12744.728061] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 11 in queue 0
[12744.728102] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 11 in queue 0
[12744.728111] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 11 in queue 0
[12744.908102] wlan0: authenticate with 00:1f:1f:5a:a1:30
[12744.920602] wlan0: send auth to 00:1f:1f:5a:a1:30 (try 1/3)
[12744.922798] wlan0: authenticated
[12744.922981] rt2800usb 1-1:1.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[12744.922989] rt2800usb 1-1:1.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[12744.923967] wlan0: associate with 00:1f:1f:5a:a1:30 (try 1/3)
[12744.937837] wlan0: RX AssocResp from 00:1f:1f:5a:a1:30 (capab=0x411 status=0 aid=194)
[12744.937846] wlan0: invalid AID value 0xc2; bits 15:14 not set
[12744.942219] wlan0: associated
[12744.942266] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[12745.044919] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[12745.044952] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[12745.044958] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[12865.223877] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
[12865.299503] brcmfmac: brcmf_sdio_chip_drivestrengthinit: No SDIO Drive strength init done for chip 4324 rev 5 pmurev 17
[12866.393551] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000): clkctl 0x50
[12867.402386] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000): clkctl 0x50
[12867.409143] brcmfmac: brcmf_proto_cdc_query_dcmd: brcmf_proto_cdc_msg failed w/status -5
[12867.409149] brcmfmac: brcmf_fil_cmd_data: Failed err=-5
[12867.409153] brcmfmac: brcmf_c_preinit_dcmds: Retreiving cur_etheraddr failed, -5
[12867.409157] brcmfmac: brcmf_bus_start: failed: -5
[12867.409167] brcmfmac: brcmf_sdbrcm_probe: dongle is not responding
[12868.416890] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000): clkctl 0x50
[12869.426308] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000): clkctl 0x50
[12869.426613] usbcore: registered new interface driver brcmfmac
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac, BCM43241
2013-09-11 23:39 ` Jan-Oliver Kaiser
@ 2013-09-12 0:18 ` Franky Lin
0 siblings, 0 replies; 6+ messages in thread
From: Franky Lin @ 2013-09-12 0:18 UTC (permalink / raw)
To: mail; +Cc: linux-wireless
Hi Jan-Oliver,
I think the problem is from the firmware since the 43241 used here is
quite different from the one we published firmware for. We are preparing
a new firmware and will release it soon.
Regards,
Franky
On 09/11/2013 04:39 PM, Jan-Oliver Kaiser wrote:
> Hi Franky,
>
> Thank you for your response. I'll attach the full dmesg output. The
> device is a Sony Vaio Duo 13 laptop (SVD1321C5E).
>
> The dmesg part I posted in the first mail is (as far as I can tell) the
> only part related to the built-in wireless adapter. I have another
> wireless adapter attached via USB, which is responsible for earlier
> output related to wireless stuff.
>
> The dmesg entries about brcmfmac are triggered simply by `modprobe
> brmcfmac`.
>
> Best regards,
> Jan-Oliver
>
> P.S.:
> I read somewhere that the wireless adapter and the touchscreen, which is
> also not working, are both connected via an Intel GPIO Controller but I
> can't seem to find the source. I don't know what that means or if it is
> true. Maybe somebody here can make use of this information.
>
>
> On 09/12/2013 12:41 AM, Franky Lin wrote:
>> Hi Jan-Oliver,
>>
>> Could you please send us the full log? Also please share more details
>> about the hardware platform you are using. We need to figure out how to
>> get the nvram file.
>>
>> Regards,
>> Franky
>>
>> On 09/11/2013 01:35 PM, Jan-Oliver Kaiser wrote:
>>> Hi,
>>>
>>> I am trying to get a BCM43241 card running on a 3.11-amd64 kernel.
>>> [1] lists the device as supported but gives no instructions on how to
>>> install it. I managed to extract the firmware from the git binary patch
>>> contained in [2].
>>>
>>> I copied the firmware to /lib/firmware/brcm/brcmfmac-sdio.bin and copied
>>> the content of /dev/nvram to /lib/firmware/brcm/brcmfmac-sdio.txt.
>>>
>>> Previously, `dmesg` would list error that indicated missing files.
>>> Currently, the output is as follows:
>>>
>>> [12865.299503] brcmfmac: brcmf_sdio_chip_drivestrengthinit: No SDIO
>>> Drive strength init done for chip 4324 rev 5 pmurev 17
>>> [12866.393551] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
>>> clkctl 0x50
>>> [12867.402386] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
>>> clkctl 0x50
>>> [12867.409143] brcmfmac: brcmf_proto_cdc_query_dcmd: brcmf_proto_cdc_msg
>>> failed w/status -5
>>> [12867.409149] brcmfmac: brcmf_fil_cmd_data: Failed err=-5
>>> [12867.409153] brcmfmac: brcmf_c_preinit_dcmds: Retreiving cur_etheraddr
>>> failed, -5
>>> [12867.409157] brcmfmac: brcmf_bus_start: failed: -5
>>> [12867.409167] brcmfmac: brcmf_sdbrcm_probe: dongle is not responding
>>> [12868.416890] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
>>> clkctl 0x50
>>> [12869.426308] brcmfmac: brcmf_sdbrcm_htclk: HT Avail timeout (1000000):
>>> clkctl 0x50
>>>
>>> I have not been able to find anything to help with debugging this.
>>>
>>> There was some discussion in response to [2] that I don't understand. Is
>>> there something wrong with the firmware itself?
>>>
>>> I would be very grateful for any help. I can provide all additional
>>> information if something is missing from this report. (I can also be
>>> reached via IRC, 'Eruquen' on freenode)
>>>
>>> Thanks in advance,
>>> Jan-Oliver
>>>
>>> [1] http://wireless.kernel.org/en/users/Drivers/brcm80211
>>> [2] http://www.spinics.net/lists/linux-wireless/msg107754.html
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe
>>> linux-wireless" in
>>> the body of a message to majordomo@vger.kernel.org
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>
>>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac, BCM43241
2013-09-11 20:35 brcmfmac, BCM43241 Jan-Oliver Kaiser
2013-09-11 22:41 ` Franky Lin
@ 2013-09-13 17:16 ` Franky Lin
2013-09-13 17:41 ` Jan-Oliver Kaiser
1 sibling, 1 reply; 6+ messages in thread
From: Franky Lin @ 2013-09-13 17:16 UTC (permalink / raw)
To: mail; +Cc: linux-wireless
On 09/11/2013 01:35 PM, Jan-Oliver Kaiser wrote:
> I copied the firmware to /lib/firmware/brcm/brcmfmac-sdio.bin and copied
> the content of /dev/nvram to /lib/firmware/brcm/brcmfmac-sdio.txt.
Hi Jan-Oliver,
Could you share me the nvram file you retrieve through /dev/nvram? Which
distro are you using?
Thanks,
Franky
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac, BCM43241
2013-09-13 17:16 ` Franky Lin
@ 2013-09-13 17:41 ` Jan-Oliver Kaiser
0 siblings, 0 replies; 6+ messages in thread
From: Jan-Oliver Kaiser @ 2013-09-13 17:41 UTC (permalink / raw)
To: frankyl; +Cc: linux-wireless
[-- Attachment #1: Type: text/plain, Size: 511 bytes --]
Hi Franky,
The nvram file is attached to this mail. I am using aptosid, based on
Debian unstable.
Best regards,
Jan-Oliver
On 09/13/2013 07:16 PM, Franky Lin wrote:
> On 09/11/2013 01:35 PM, Jan-Oliver Kaiser wrote:
>> I copied the firmware to /lib/firmware/brcm/brcmfmac-sdio.bin and copied
>> the content of /dev/nvram to /lib/firmware/brcm/brcmfmac-sdio.txt.
> Hi Jan-Oliver,
>
> Could you share me the nvram file you retrieve through /dev/nvram? Which
> distro are you using?
>
> Thanks,
> Franky
>
[-- Attachment #2: nvram --]
[-- Type: text/plain, Size: 114 bytes --]
ÿ\0ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ\x1dâÿÿ ÿÿ\a\0\x12\0\0\0\0\0\0\0\0V\0\0\0\x01ÿ\x01\x01ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ\a\0ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2013-09-13 17:41 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-09-11 20:35 brcmfmac, BCM43241 Jan-Oliver Kaiser
2013-09-11 22:41 ` Franky Lin
2013-09-11 23:39 ` Jan-Oliver Kaiser
2013-09-12 0:18 ` Franky Lin
2013-09-13 17:16 ` Franky Lin
2013-09-13 17:41 ` Jan-Oliver Kaiser
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).