From: zhuyj <zyjzyj2000@gmail.com>
To: linux-wireless@vger.kernel.org
Cc: zhuyj <zyjzyj2000@gmail.com>, "Liu, Bopeng" <Bopeng.Liu@windriver.com>
Subject: Re: 802.11a is supported in AP mode or not?
Date: Wed, 22 Jan 2014 18:33:06 +0800 [thread overview]
Message-ID: <52DF9E62.7080301@gmail.com> (raw)
In-Reply-To: <52DF947E.40800@gmail.com>
Hi, maintainers
The kernel version:
uname -a
Linux wind-desktop 3.13.0-test-iwlwifi #1 SMP Mon Jan 20 18:54:22 CST
2014 x86_64 x86_64 x86_64 GNU/Linux
Any reply is appreciated.
Best Regards!
Zhu Yanjun
On 01/22/2014 05:50 PM, zhuyj wrote:
> Hi, maintainers
>
> I made tests on ubuntu 13.10. I followed these steps.
> From the following logs, we can see 802.11a is not supported in
> channel list.
> I want to know whether 802.11a supports this or not? Or 802.11a is not
> used in this?
> Chip is 6205. lspci -vvv is as below.
>
> Thanks a lot.
> Zhu Yanjun
>
> 1. installed ubuntu 13.10 client
>
> 2. git clone
> git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
> linux-git
>
> 3. apt-get install kernel-package
>
> 4. make-kpkg --initrd --append-to-version=-test-iwlwifi kernel_image
> kernel-headers
>
> 5. dpkg -i linux-headers-
> dpkg -i linux-images-
>
> 6.reboot ubuntu 13.10
>
> 7. $ vi /etc/hostapd.conf
> interface=wlan0
> driver=nl80211
> logger_syslog=-1
> logger_syslog_level=2
> logger_stdout=-1
> logger_stdout_level=2
> dump_file=/tmp/hostapd.dump
> ctrl_interface=/var/run/hostapd
> ctrl_interface_group=0
> ssid=test
> country_code=US
> hw_mode=a
> channel=2
> beacon_int=100
> dtim_period=2
> max_num_sta=255
> rts_threshold=2347
> fragm_threshold=2346
> macaddr_acl=0
> auth_algs=3
> ignore_broadcast_ssid=0
> wmm_enabled=1
> wmm_ac_bk_cwmin=4
> wmm_ac_bk_cwmax=10
> wmm_ac_bk_aifs=7
> wmm_ac_bk_txop_limit=0
> wmm_ac_bk_acm=0
> wmm_ac_be_aifs=3
> wmm_ac_be_cwmin=4
> wmm_ac_be_cwmax=10
> wmm_ac_be_txop_limit=0
> wmm_ac_be_acm=0
> wmm_ac_vi_aifs=2
> wmm_ac_vi_cwmin=3
> wmm_ac_vi_cwmax=4
> wmm_ac_vi_txop_limit=94
> wmm_ac_vi_acm=0
> wmm_ac_vo_aifs=2
> wmm_ac_vo_cwmin=2
> wmm_ac_vo_cwmax=3
> wmm_ac_vo_txop_limit=47
> wmm_ac_vo_acm=0
> eap_server=0
> wpa=2
> wpa_passphrase=12345678
> wpa_key_mgmt=WPA-PSK
> wpa_pairwise=TKIP CCMP
> wpa_group_rekey=600
> wpa_gmk_rekey=86400
>
> 8. hostapd -B /etc/hostapd.conf -dd
> random: Trying to read entropy from /dev/random
> Configuration file: /etc/hostapd.conf
> ctrl_interface_group=0
> nl80211: interface wlan0 in phy phy0
> rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
> nl80211: Using driver-based off-channel TX
> nl80211: Register frame command failed (type=208): ret=-114 (Operation
> already in progress)
> nl80211: Register frame match - hexdump(len=2): 04 0a
> nl80211: Failed to register Action frame processing - ignore for now
> nl80211: Add own interface ifindex 3
> nl80211: Set mode ifindex 3 iftype 3 (AP)
> nl80211: Create interface iftype 6 (MONITOR)
> nl80211: New interface mon.wlan0 created: ifindex=4
> nl80211: Add own interface ifindex 4
> BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
> nl80211: Regulatory information - country=00
> nl80211: 2402-2472 @ 40 MHz
> nl80211: 2457-2482 @ 40 MHz
> nl80211: 2474-2494 @ 20 MHz
> nl80211: 5170-5250 @ 40 MHz
> nl80211: 5735-5835 @ 40 MHz
> nl80211: Added 802.11b mode based on 802.11g information
> Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm
> Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm
> Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm
> wlan0: IEEE 802.11 Configured channel (1) not found from the channel
> list of current mode (2) IEEE 802.11a
> wlan0: IEEE 802.11 Hardware does not support configured channel
> Could not select hw_mode and channel. (-4)
> wlan0: Unable to setup interface.
> Flushing old station entries
> Deauthenticate all stations
> rmdir[ctrl_interface]: No such file or directory
> nl80211: Remove interface ifindex=4
> netlink: Operstate: linkmode=0, operstate=6
> nl80211: Set mode ifindex 3 iftype 2 (STATION)
>
> lspci -vvv
>
> 01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205
> [Taylor Peak] (rev 34)
> Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 45
> Region 0: Memory at f7500000 (64-bit, non-prefetchable) [size=8K]
> Capabilities: [c8] Power Management version 3
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee003d8 Data: 0000
> Capabilities: [e0] Express (v1) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <512ns, L1 unlimited
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
> TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0 <4us, L1 <32us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain-
> CommClk+
> ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
> DLActive- BWMgmt- ABWMgmt-
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap-
> ChkEn-
> Capabilities: [140 v1] Device Serial Number a0-88-b4-ff-ff-70-91-20
> Kernel driver in use: iwlwifi
>
>
next prev parent reply other threads:[~2014-01-22 10:33 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-22 9:50 802.11a is supported in AP mode or not? zhuyj
2014-01-22 10:33 ` zhuyj [this message]
2014-01-22 10:47 ` Liu, Bopeng
2014-01-22 14:51 ` Pat Erley
2014-01-22 21:20 ` Krishna Chaitanya
2014-01-23 2:00 ` Liu, Bopeng
2014-01-23 6:15 ` Krishna Chaitanya
2014-01-23 6:37 ` Liu, Bopeng
2014-01-23 6:44 ` zhuyj
2014-01-23 8:23 ` Emmanuel Grumbach
2014-01-23 8:36 ` Liu, Bopeng
2014-01-23 8:41 ` Liu, Bopeng
2014-01-23 8:50 ` zhuyj
2014-01-23 8:57 ` Krishna Chaitanya
2014-01-23 8:59 ` Liu, Bopeng
2014-01-23 9:04 ` Krishna Chaitanya
2014-01-23 9:07 ` Liu, Bopeng
2014-01-23 9:20 ` Liu, Bopeng
2014-01-23 9:21 ` Liu, Bopeng
2014-01-23 9:27 ` Emmanuel Grumbach
2014-01-23 9:29 ` Krishna Chaitanya
2014-01-23 9:34 ` Liu, Bopeng
2014-01-23 9:36 ` Liu, Bopeng
2014-01-23 9:49 ` Emmanuel Grumbach
2014-01-24 5:27 ` Liu, Bopeng
2014-01-27 21:21 ` Anand Moon
2014-01-27 21:59 ` Anand Moon
2014-01-24 6:26 ` Liu, Bopeng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=52DF9E62.7080301@gmail.com \
--to=zyjzyj2000@gmail.com \
--cc=Bopeng.Liu@windriver.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).