* 802.11a is supported in AP mode or not?
@ 2014-01-22 9:50 zhuyj
2014-01-22 10:33 ` zhuyj
` (2 more replies)
0 siblings, 3 replies; 28+ messages in thread
From: zhuyj @ 2014-01-22 9:50 UTC (permalink / raw)
To: linux-wireless; +Cc: zhuyj, Liu, Bopeng
Hi, maintainers
I made tests on ubuntu 13.10. I followed these steps.
From the following logs, we can see 802.11a is not supported in channel
list.
I want to know whether 802.11a supports this or not? Or 802.11a is not
used in this?
Chip is 6205. lspci -vvv is as below.
Thanks a lot.
Zhu Yanjun
1. installed ubuntu 13.10 client
2. git clone
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git linux-git
3. apt-get install kernel-package
4. make-kpkg --initrd --append-to-version=-test-iwlwifi kernel_image
kernel-headers
5. dpkg -i linux-headers-
dpkg -i linux-images-
6.reboot ubuntu 13.10
7. $ vi /etc/hostapd.conf
interface=wlan0
driver=nl80211
logger_syslog=-1
logger_syslog_level=2
logger_stdout=-1
logger_stdout_level=2
dump_file=/tmp/hostapd.dump
ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
ssid=test
country_code=US
hw_mode=a
channel=2
beacon_int=100
dtim_period=2
max_num_sta=255
rts_threshold=2347
fragm_threshold=2346
macaddr_acl=0
auth_algs=3
ignore_broadcast_ssid=0
wmm_enabled=1
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
wmm_ac_bk_aifs=7
wmm_ac_bk_txop_limit=0
wmm_ac_bk_acm=0
wmm_ac_be_aifs=3
wmm_ac_be_cwmin=4
wmm_ac_be_cwmax=10
wmm_ac_be_txop_limit=0
wmm_ac_be_acm=0
wmm_ac_vi_aifs=2
wmm_ac_vi_cwmin=3
wmm_ac_vi_cwmax=4
wmm_ac_vi_txop_limit=94
wmm_ac_vi_acm=0
wmm_ac_vo_aifs=2
wmm_ac_vo_cwmin=2
wmm_ac_vo_cwmax=3
wmm_ac_vo_txop_limit=47
wmm_ac_vo_acm=0
eap_server=0
wpa=2
wpa_passphrase=12345678
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP CCMP
wpa_group_rekey=600
wpa_gmk_rekey=86400
8. hostapd -B /etc/hostapd.conf -dd
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd.conf
ctrl_interface_group=0
nl80211: interface wlan0 in phy phy0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
nl80211: Using driver-based off-channel TX
nl80211: Register frame command failed (type=208): ret=-114 (Operation
already in progress)
nl80211: Register frame match - hexdump(len=2): 04 0a
nl80211: Failed to register Action frame processing - ignore for now
nl80211: Add own interface ifindex 3
nl80211: Set mode ifindex 3 iftype 3 (AP)
nl80211: Create interface iftype 6 (MONITOR)
nl80211: New interface mon.wlan0 created: ifindex=4
nl80211: Add own interface ifindex 4
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz
nl80211: 2457-2482 @ 40 MHz
nl80211: 2474-2494 @ 20 MHz
nl80211: 5170-5250 @ 40 MHz
nl80211: 5735-5835 @ 40 MHz
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm
wlan0: IEEE 802.11 Configured channel (1) not found from the channel
list of current mode (2) IEEE 802.11a
wlan0: IEEE 802.11 Hardware does not support configured channel
Could not select hw_mode and channel. (-4)
wlan0: Unable to setup interface.
Flushing old station entries
Deauthenticate all stations
rmdir[ctrl_interface]: No such file or directory
nl80211: Remove interface ifindex=4
netlink: Operstate: linkmode=0, operstate=6
nl80211: Set mode ifindex 3 iftype 2 (STATION)
lspci -vvv
01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205
[Taylor Peak] (rev 34)
Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f7500000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee003d8 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <4us, L1 <32us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number a0-88-b4-ff-ff-70-91-20
Kernel driver in use: iwlwifi
^ permalink raw reply [flat|nested] 28+ messages in thread* Re: 802.11a is supported in AP mode or not? 2014-01-22 9:50 802.11a is supported in AP mode or not? zhuyj @ 2014-01-22 10:33 ` zhuyj 2014-01-22 10:47 ` Liu, Bopeng 2014-01-22 14:51 ` Pat Erley 2014-01-22 21:20 ` Krishna Chaitanya 2 siblings, 1 reply; 28+ messages in thread From: zhuyj @ 2014-01-22 10:33 UTC (permalink / raw) To: linux-wireless; +Cc: zhuyj, Liu, Bopeng Hi, maintainers The kernel version: uname -a Linux wind-desktop 3.13.0-test-iwlwifi #1 SMP Mon Jan 20 18:54:22 CST 2014 x86_64 x86_64 x86_64 GNU/Linux Any reply is appreciated. Best Regards! Zhu Yanjun On 01/22/2014 05:50 PM, zhuyj wrote: > Hi, maintainers > > I made tests on ubuntu 13.10. I followed these steps. > From the following logs, we can see 802.11a is not supported in > channel list. > I want to know whether 802.11a supports this or not? Or 802.11a is not > used in this? > Chip is 6205. lspci -vvv is as below. > > Thanks a lot. > Zhu Yanjun > > 1. installed ubuntu 13.10 client > > 2. git clone > git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git > linux-git > > 3. apt-get install kernel-package > > 4. make-kpkg --initrd --append-to-version=-test-iwlwifi kernel_image > kernel-headers > > 5. dpkg -i linux-headers- > dpkg -i linux-images- > > 6.reboot ubuntu 13.10 > > 7. $ vi /etc/hostapd.conf > interface=wlan0 > driver=nl80211 > logger_syslog=-1 > logger_syslog_level=2 > logger_stdout=-1 > logger_stdout_level=2 > dump_file=/tmp/hostapd.dump > ctrl_interface=/var/run/hostapd > ctrl_interface_group=0 > ssid=test > country_code=US > hw_mode=a > channel=2 > beacon_int=100 > dtim_period=2 > max_num_sta=255 > rts_threshold=2347 > fragm_threshold=2346 > macaddr_acl=0 > auth_algs=3 > ignore_broadcast_ssid=0 > wmm_enabled=1 > wmm_ac_bk_cwmin=4 > wmm_ac_bk_cwmax=10 > wmm_ac_bk_aifs=7 > wmm_ac_bk_txop_limit=0 > wmm_ac_bk_acm=0 > wmm_ac_be_aifs=3 > wmm_ac_be_cwmin=4 > wmm_ac_be_cwmax=10 > wmm_ac_be_txop_limit=0 > wmm_ac_be_acm=0 > wmm_ac_vi_aifs=2 > wmm_ac_vi_cwmin=3 > wmm_ac_vi_cwmax=4 > wmm_ac_vi_txop_limit=94 > wmm_ac_vi_acm=0 > wmm_ac_vo_aifs=2 > wmm_ac_vo_cwmin=2 > wmm_ac_vo_cwmax=3 > wmm_ac_vo_txop_limit=47 > wmm_ac_vo_acm=0 > eap_server=0 > wpa=2 > wpa_passphrase=12345678 > wpa_key_mgmt=WPA-PSK > wpa_pairwise=TKIP CCMP > wpa_group_rekey=600 > wpa_gmk_rekey=86400 > > 8. hostapd -B /etc/hostapd.conf -dd > random: Trying to read entropy from /dev/random > Configuration file: /etc/hostapd.conf > ctrl_interface_group=0 > nl80211: interface wlan0 in phy phy0 > rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 > nl80211: Using driver-based off-channel TX > nl80211: Register frame command failed (type=208): ret=-114 (Operation > already in progress) > nl80211: Register frame match - hexdump(len=2): 04 0a > nl80211: Failed to register Action frame processing - ignore for now > nl80211: Add own interface ifindex 3 > nl80211: Set mode ifindex 3 iftype 3 (AP) > nl80211: Create interface iftype 6 (MONITOR) > nl80211: New interface mon.wlan0 created: ifindex=4 > nl80211: Add own interface ifindex 4 > BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) > nl80211: Regulatory information - country=00 > nl80211: 2402-2472 @ 40 MHz > nl80211: 2457-2482 @ 40 MHz > nl80211: 2474-2494 @ 20 MHz > nl80211: 5170-5250 @ 40 MHz > nl80211: 5735-5835 @ 40 MHz > nl80211: Added 802.11b mode based on 802.11g information > Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm > wlan0: IEEE 802.11 Configured channel (1) not found from the channel > list of current mode (2) IEEE 802.11a > wlan0: IEEE 802.11 Hardware does not support configured channel > Could not select hw_mode and channel. (-4) > wlan0: Unable to setup interface. > Flushing old station entries > Deauthenticate all stations > rmdir[ctrl_interface]: No such file or directory > nl80211: Remove interface ifindex=4 > netlink: Operstate: linkmode=0, operstate=6 > nl80211: Set mode ifindex 3 iftype 2 (STATION) > > lspci -vvv > > 01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205 > [Taylor Peak] (rev 34) > Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 45 > Region 0: Memory at f7500000 (64-bit, non-prefetchable) [size=8K] > Capabilities: [c8] Power Management version 3 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee003d8 Data: 0000 > Capabilities: [e0] Express (v1) Endpoint, MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s > <512ns, L1 unlimited > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, > Latency L0 <4us, L1 <32us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- > CommClk+ > ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- > ChkEn- > Capabilities: [140 v1] Device Serial Number a0-88-b4-ff-ff-70-91-20 > Kernel driver in use: iwlwifi > > ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-22 10:33 ` zhuyj @ 2014-01-22 10:47 ` Liu, Bopeng 0 siblings, 0 replies; 28+ messages in thread From: Liu, Bopeng @ 2014-01-22 10:47 UTC (permalink / raw) To: zhuyj, linux-wireless@vger.kernel.org root@WR-IntelligentDevice:~# lspci -v | grep 6205 01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205 [Taylor Peak] (rev 34) Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN root@WR-IntelligentDevice:~# Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: zhuyj [zyjzyj2000@gmail.com] Sent: Wednesday, January 22, 2014 6:33 PM To: linux-wireless@vger.kernel.org Cc: zhuyj; Liu, Bopeng Subject: Re: 802.11a is supported in AP mode or not? Hi, maintainers The kernel version: uname -a Linux wind-desktop 3.13.0-test-iwlwifi #1 SMP Mon Jan 20 18:54:22 CST 2014 x86_64 x86_64 x86_64 GNU/Linux Any reply is appreciated. Best Regards! Zhu Yanjun On 01/22/2014 05:50 PM, zhuyj wrote: > Hi, maintainers > > I made tests on ubuntu 13.10. I followed these steps. > From the following logs, we can see 802.11a is not supported in > channel list. > I want to know whether 802.11a supports this or not? Or 802.11a is not > used in this? > Chip is 6205. lspci -vvv is as below. > > Thanks a lot. > Zhu Yanjun > > 1. installed ubuntu 13.10 client > > 2. git clone > git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git > linux-git > > 3. apt-get install kernel-package > > 4. make-kpkg --initrd --append-to-version=-test-iwlwifi kernel_image > kernel-headers > > 5. dpkg -i linux-headers- > dpkg -i linux-images- > > 6.reboot ubuntu 13.10 > > 7. $ vi /etc/hostapd.conf > interface=wlan0 > driver=nl80211 > logger_syslog=-1 > logger_syslog_level=2 > logger_stdout=-1 > logger_stdout_level=2 > dump_file=/tmp/hostapd.dump > ctrl_interface=/var/run/hostapd > ctrl_interface_group=0 > ssid=test > country_code=US > hw_mode=a > channel=2 > beacon_int=100 > dtim_period=2 > max_num_sta=255 > rts_threshold=2347 > fragm_threshold=2346 > macaddr_acl=0 > auth_algs=3 > ignore_broadcast_ssid=0 > wmm_enabled=1 > wmm_ac_bk_cwmin=4 > wmm_ac_bk_cwmax=10 > wmm_ac_bk_aifs=7 > wmm_ac_bk_txop_limit=0 > wmm_ac_bk_acm=0 > wmm_ac_be_aifs=3 > wmm_ac_be_cwmin=4 > wmm_ac_be_cwmax=10 > wmm_ac_be_txop_limit=0 > wmm_ac_be_acm=0 > wmm_ac_vi_aifs=2 > wmm_ac_vi_cwmin=3 > wmm_ac_vi_cwmax=4 > wmm_ac_vi_txop_limit=94 > wmm_ac_vi_acm=0 > wmm_ac_vo_aifs=2 > wmm_ac_vo_cwmin=2 > wmm_ac_vo_cwmax=3 > wmm_ac_vo_txop_limit=47 > wmm_ac_vo_acm=0 > eap_server=0 > wpa=2 > wpa_passphrase=12345678 > wpa_key_mgmt=WPA-PSK > wpa_pairwise=TKIP CCMP > wpa_group_rekey=600 > wpa_gmk_rekey=86400 > > 8. hostapd -B /etc/hostapd.conf -dd > random: Trying to read entropy from /dev/random > Configuration file: /etc/hostapd.conf > ctrl_interface_group=0 > nl80211: interface wlan0 in phy phy0 > rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 > nl80211: Using driver-based off-channel TX > nl80211: Register frame command failed (type=208): ret=-114 (Operation > already in progress) > nl80211: Register frame match - hexdump(len=2): 04 0a > nl80211: Failed to register Action frame processing - ignore for now > nl80211: Add own interface ifindex 3 > nl80211: Set mode ifindex 3 iftype 3 (AP) > nl80211: Create interface iftype 6 (MONITOR) > nl80211: New interface mon.wlan0 created: ifindex=4 > nl80211: Add own interface ifindex 4 > BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) > nl80211: Regulatory information - country=00 > nl80211: 2402-2472 @ 40 MHz > nl80211: 2457-2482 @ 40 MHz > nl80211: 2474-2494 @ 20 MHz > nl80211: 5170-5250 @ 40 MHz > nl80211: 5735-5835 @ 40 MHz > nl80211: Added 802.11b mode based on 802.11g information > Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm > wlan0: IEEE 802.11 Configured channel (1) not found from the channel > list of current mode (2) IEEE 802.11a > wlan0: IEEE 802.11 Hardware does not support configured channel > Could not select hw_mode and channel. (-4) > wlan0: Unable to setup interface. > Flushing old station entries > Deauthenticate all stations > rmdir[ctrl_interface]: No such file or directory > nl80211: Remove interface ifindex=4 > netlink: Operstate: linkmode=0, operstate=6 > nl80211: Set mode ifindex 3 iftype 2 (STATION) > > lspci -vvv > > 01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205 > [Taylor Peak] (rev 34) > Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 45 > Region 0: Memory at f7500000 (64-bit, non-prefetchable) [size=8K] > Capabilities: [c8] Power Management version 3 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee003d8 Data: 0000 > Capabilities: [e0] Express (v1) Endpoint, MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s > <512ns, L1 unlimited > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, > Latency L0 <4us, L1 <32us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- > CommClk+ > ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- > ChkEn- > Capabilities: [140 v1] Device Serial Number a0-88-b4-ff-ff-70-91-20 > Kernel driver in use: iwlwifi > > ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-22 9:50 802.11a is supported in AP mode or not? zhuyj 2014-01-22 10:33 ` zhuyj @ 2014-01-22 14:51 ` Pat Erley 2014-01-22 21:20 ` Krishna Chaitanya 2 siblings, 0 replies; 28+ messages in thread From: Pat Erley @ 2014-01-22 14:51 UTC (permalink / raw) To: zhuyj, linux-wireless; +Cc: Liu, Bopeng On 01/22/2014 03:50 AM, zhuyj wrote: > Hi, maintainers > > I made tests on ubuntu 13.10. I followed these steps. > From the following logs, we can see 802.11a is not supported in channel > list. > I want to know whether 802.11a supports this or not? Or 802.11a is not > used in this? > Chip is 6205. lspci -vvv is as below. > > Thanks a lot. > Zhu Yanjun > > 1. installed ubuntu 13.10 client > > 2. git clone > git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git linux-git > > 3. apt-get install kernel-package > > 4. make-kpkg --initrd --append-to-version=-test-iwlwifi kernel_image > kernel-headers > > 5. dpkg -i linux-headers- > dpkg -i linux-images- > > 6.reboot ubuntu 13.10 > > 7. $ vi /etc/hostapd.conf > interface=wlan0 > driver=nl80211 > logger_syslog=-1 > logger_syslog_level=2 > logger_stdout=-1 > logger_stdout_level=2 > dump_file=/tmp/hostapd.dump > ctrl_interface=/var/run/hostapd > ctrl_interface_group=0 > ssid=test > country_code=US > hw_mode=a > channel=2 Channel 2 is in the 2.4ghz band (B/G) not 5ghz (A) > beacon_int=100 > dtim_period=2 > max_num_sta=255 > rts_threshold=2347 > fragm_threshold=2346 > macaddr_acl=0 > auth_algs=3 > ignore_broadcast_ssid=0 > wmm_enabled=1 > wmm_ac_bk_cwmin=4 > wmm_ac_bk_cwmax=10 > wmm_ac_bk_aifs=7 > wmm_ac_bk_txop_limit=0 > wmm_ac_bk_acm=0 > wmm_ac_be_aifs=3 > wmm_ac_be_cwmin=4 > wmm_ac_be_cwmax=10 > wmm_ac_be_txop_limit=0 > wmm_ac_be_acm=0 > wmm_ac_vi_aifs=2 > wmm_ac_vi_cwmin=3 > wmm_ac_vi_cwmax=4 > wmm_ac_vi_txop_limit=94 > wmm_ac_vi_acm=0 > wmm_ac_vo_aifs=2 > wmm_ac_vo_cwmin=2 > wmm_ac_vo_cwmax=3 > wmm_ac_vo_txop_limit=47 > wmm_ac_vo_acm=0 > eap_server=0 > wpa=2 > wpa_passphrase=12345678 > wpa_key_mgmt=WPA-PSK > wpa_pairwise=TKIP CCMP > wpa_group_rekey=600 > wpa_gmk_rekey=86400 > ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-22 9:50 802.11a is supported in AP mode or not? zhuyj 2014-01-22 10:33 ` zhuyj 2014-01-22 14:51 ` Pat Erley @ 2014-01-22 21:20 ` Krishna Chaitanya 2014-01-23 2:00 ` Liu, Bopeng 2 siblings, 1 reply; 28+ messages in thread From: Krishna Chaitanya @ 2014-01-22 21:20 UTC (permalink / raw) To: zhuyj; +Cc: linux-wireless, Liu, Bopeng On Wed, Jan 22, 2014 at 3:20 PM, zhuyj <zyjzyj2000@gmail.com> wrote: > Hi, maintainers > > I made tests on ubuntu 13.10. I followed these steps. > From the following logs, we can see 802.11a is not supported in channel > list. > I want to know whether 802.11a supports this or not? Or 802.11a is not used > in this? > Chip is 6205. lspci -vvv is as below. Its a AGN card, so it supports 5GHz. Also From the other Thread: On Wed, Jan 22, 2014 at 4:27 PM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > > AP Mode: > > hw_mode can't be supported, have you ever met such problem? > > > hostapd -B /etc/hostapd.conf > Configuration file: /etc/hostapd.conf > channel [9] (104) is disabled for use in AP mode, flags: 0x1 > wlan0: IEEE 802.11 Configured channel (104) not found from the channel list of current mode (2) IEEE 802.11a > wlan0: IEEE 802.11 Hardware does not support configured channel > Could not select hw_mode and channel. (-4) > wlan0: Unable to setup interface. > Channel 104 is a DFS channel which is not allowed in country US. Please use a non-DFS channel like 36/40/149 and then try (or) change the country_code which has 104 allowed :-). You can also use "iw reg get" to get list of bands allowed, all the bands marked with passive-scan are not allowed in AP mode unless we implement full DFS functionality (CAC) and make the channel usable. Also use a separate thread, dont post in other threads. ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-22 21:20 ` Krishna Chaitanya @ 2014-01-23 2:00 ` Liu, Bopeng 2014-01-23 6:15 ` Krishna Chaitanya 0 siblings, 1 reply; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 2:00 UTC (permalink / raw) To: Krishna Chaitanya, zhuyj; +Cc: linux-wireless Thanks for your mail, but very pity, after checking, it doesn't as well. May you test it on your board? # iw reg get country US: (2402 - 2472 @ 40), (30, 0) (5170 - 5250 @ 80), (17, 0) (5250 - 5330 @ 80), (23, 0) (5735 - 5835 @ 80), (30, 0) (57240 - 63720 @ 2160), (40, 0) country_code=US hw_mode=a channel=149 #hostapd -B /etc/hostapd.conf Configuration file: /etc/hostapd.conf channel [19] (149) is disabled for use in AP mode, flags: 0x7 wlan0: IEEE 802.11 Configured channel (149) not found from the channel list of current mode (2) IEEE 802.11a wlan0: IEEE 802.11 Hardware does not support configured channel Could not select hw_mode and channel. (-4) wlan0: Unable to setup interface. rmdir[ctrl_interface]: No such file or directory Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: linux-wireless-owner@vger.kernel.org [linux-wireless-owner@vger.kernel.org] on behalf of Krishna Chaitanya [chaitanya.mgit@gmail.com] Sent: Thursday, January 23, 2014 5:20 AM To: zhuyj Cc: linux-wireless; Liu, Bopeng Subject: Re: 802.11a is supported in AP mode or not? On Wed, Jan 22, 2014 at 3:20 PM, zhuyj <zyjzyj2000@gmail.com> wrote: > Hi, maintainers > > I made tests on ubuntu 13.10. I followed these steps. > From the following logs, we can see 802.11a is not supported in channel > list. > I want to know whether 802.11a supports this or not? Or 802.11a is not used > in this? > Chip is 6205. lspci -vvv is as below. Its a AGN card, so it supports 5GHz. Also From the other Thread: On Wed, Jan 22, 2014 at 4:27 PM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > > AP Mode: > > hw_mode can't be supported, have you ever met such problem? > > > hostapd -B /etc/hostapd.conf > Configuration file: /etc/hostapd.conf > channel [9] (104) is disabled for use in AP mode, flags: 0x1 > wlan0: IEEE 802.11 Configured channel (104) not found from the channel list of current mode (2) IEEE 802.11a > wlan0: IEEE 802.11 Hardware does not support configured channel > Could not select hw_mode and channel. (-4) > wlan0: Unable to setup interface. > Channel 104 is a DFS channel which is not allowed in country US. Please use a non-DFS channel like 36/40/149 and then try (or) change the country_code which has 104 allowed :-). You can also use "iw reg get" to get list of bands allowed, all the bands marked with passive-scan are not allowed in AP mode unless we implement full DFS functionality (CAC) and make the channel usable. Also use a separate thread, dont post in other threads. -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-23 2:00 ` Liu, Bopeng @ 2014-01-23 6:15 ` Krishna Chaitanya 2014-01-23 6:37 ` Liu, Bopeng 2014-01-23 6:44 ` zhuyj 0 siblings, 2 replies; 28+ messages in thread From: Krishna Chaitanya @ 2014-01-23 6:15 UTC (permalink / raw) To: Liu, Bopeng; +Cc: zhuyj, linux-wireless On Thu, Jan 23, 2014 at 7:30 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > Thanks for your mail, but very pity, after checking, it doesn't as well. May you test it on your board? > > > # iw reg get > country US: > (2402 - 2472 @ 40), (30, 0) > (5170 - 5250 @ 80), (17, 0) > (5250 - 5330 @ 80), (23, 0) > (5735 - 5835 @ 80), (30, 0) > (57240 - 63720 @ 2160), (40, 0) > > country_code=US > hw_mode=a > channel=149 > > #hostapd -B /etc/hostapd.conf > Configuration file: /etc/hostapd.conf > channel [19] (149) is disabled for use in AP mode, flags: 0x7 > wlan0: IEEE 802.11 Configured channel (149) not found from the channel list of current mode (2) IEEE 802.11a > wlan0: IEEE 802.11 Hardware does not support configured channel > Could not select hw_mode and channel. (-4) > wlan0: Unable to setup interface. > rmdir[ctrl_interface]: No such file or directory > Can you use "hostapd -dd -B /etc/hostapd.conf"and send the output? Also "hostapd -v" and "iw phy" as well. ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 6:15 ` Krishna Chaitanya @ 2014-01-23 6:37 ` Liu, Bopeng 2014-01-23 6:44 ` zhuyj 1 sibling, 0 replies; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 6:37 UTC (permalink / raw) To: Krishna Chaitanya; +Cc: zhuyj, linux-wireless root@WR-IntelligentDevice:/etc# hostapd -dd -B /etc/hostapd.conf random: Trying to read entropy from /dev/random Configuration file: /etc/hostapd.conf ctrl_interface_group=0 nl80211: interface wlan0 in phy phy0 nl80211: Using driver-based off-channel TX nl80211: Use separate P2P group interface (driver advertised support) nl80211: Add own interface ifindex 15 nl80211: Set mode ifindex 15 iftype 3 (AP) nl80211: Create interface iftype 6 (MONITOR) nl80211: New interface mon.wlan0 created: ifindex=16 nl80211: Add own interface ifindex 16 BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) nl80211: Regulatory information - country=US nl80211: 2402-2472 @ 40 MHz nl80211: 5170-5250 @ 80 MHz nl80211: 5250-5330 @ 80 MHz nl80211: 5735-5835 @ 80 MHz nl80211: 57240-63720 @ 2160 MHz nl80211: Added 802.11b mode based on 802.11g information Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=0 dBm Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=0 dBm Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=0 dBm channel [19] (149) is disabled for use in AP mode, flags: 0x7 wlan0: IEEE 802.11 Configured channel (149) not found from the channel list of current mode (2) IEEE 802.11a wlan0: IEEE 802.11 Hardware does not support configured channel Could not select hw_mode and channel. (-4) wlan0: Unable to setup interface. Flushing old station entries Deauthenticate all stations rmdir[ctrl_interface]: No such file or directory nl80211: Remove interface ifindex=16 netlink: Operstate: linkmode=0, operstate=6 nl80211: Set mode ifindex 15 iftype 2 (STATION) root@WR-IntelligentDevice:/etc# root@WR-IntelligentDevice:/etc# hostapd -v hostapd v1.0 User space daemon for IEEE 802.11 AP management, IEEE 802.1X/WPA/WPA2/EAP/RADIUS Authenticator Copyright (c) 2002-2012, Jouni Malinen <j@w1.fi> and contributors root@WR-IntelligentDevice:/etc# root@WR-IntelligentDevice:/etc# iw phy Wiphy phy0 Band 1: Frequencies: * 2412 MHz [1] (0.0 dBm) * 2417 MHz [2] (0.0 dBm) * 2422 MHz [3] (0.0 dBm) * 2427 MHz [4] (0.0 dBm) * 2432 MHz [5] (0.0 dBm) * 2437 MHz [6] (0.0 dBm) * 2442 MHz [7] (0.0 dBm) * 2447 MHz [8] (0.0 dBm) * 2452 MHz [9] (0.0 dBm) * 2457 MHz [10] (0.0 dBm) * 2462 MHz [11] (0.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Frequencies: * 5180 MHz [36] (0.0 dBm) (passive scanning, no IBSS) * 5200 MHz [40] (0.0 dBm) (passive scanning, no IBSS) * 5220 MHz [44] (0.0 dBm) (passive scanning, no IBSS) * 5240 MHz [48] (0.0 dBm) (passive scanning, no IBSS) * 5260 MHz [52] (0.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (0.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (0.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (0.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (disabled) * 5520 MHz [104] (disabled) * 5540 MHz [108] (disabled) * 5560 MHz [112] (disabled) * 5580 MHz [116] (disabled) * 5600 MHz [120] (disabled) * 5620 MHz [124] (disabled) * 5640 MHz [128] (disabled) * 5660 MHz [132] (disabled) * 5680 MHz [136] (disabled) * 5700 MHz [140] (disabled) * 5745 MHz [149] (0.0 dBm) (passive scanning, no IBSS) * 5765 MHz [153] (0.0 dBm) (passive scanning, no IBSS) * 5785 MHz [157] (0.0 dBm) (passive scanning, no IBSS) * 5805 MHz [161] (0.0 dBm) (passive scanning, no IBSS) * 5825 MHz [165] (0.0 dBm) (passive scanning, no IBSS) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 20 max scan IEs length: 255 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * AP/VLAN * monitor * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed } <= 1, #{ AP, P2P-GO } <= 1, total <= 2, #channels <= 1, STA/AP BI must match * #{ managed } <= 2, #{ P2P-client } <= 1, total <= 2, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * start_ap * new_station * new_mpath * set_mesh_config * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * frame * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * probe_client * set_noack_map * register_beacons * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 Device supports RSN-IBSS. WoWLAN support: * wake up on disconnect * wake up on magic packet * wake up on pattern match, up to 20 patterns of 16-128 bytes * can do GTK rekeying * wake up on GTK rekey failure * wake up on EAP identity request * wake up on rfkill release HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS. root@WR-IntelligentDevice:/etc# Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Krishna Chaitanya [chaitanya.mgit@gmail.com] Sent: Thursday, January 23, 2014 2:15 PM To: Liu, Bopeng Cc: zhuyj; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 7:30 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > Thanks for your mail, but very pity, after checking, it doesn't as well. May you test it on your board? > > > # iw reg get > country US: > (2402 - 2472 @ 40), (30, 0) > (5170 - 5250 @ 80), (17, 0) > (5250 - 5330 @ 80), (23, 0) > (5735 - 5835 @ 80), (30, 0) > (57240 - 63720 @ 2160), (40, 0) > > country_code=US > hw_mode=a > channel=149 > > #hostapd -B /etc/hostapd.conf > Configuration file: /etc/hostapd.conf > channel [19] (149) is disabled for use in AP mode, flags: 0x7 > wlan0: IEEE 802.11 Configured channel (149) not found from the channel list of current mode (2) IEEE 802.11a > wlan0: IEEE 802.11 Hardware does not support configured channel > Could not select hw_mode and channel. (-4) > wlan0: Unable to setup interface. > rmdir[ctrl_interface]: No such file or directory > Can you use "hostapd -dd -B /etc/hostapd.conf"and send the output? Also "hostapd -v" and "iw phy" as well. ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-23 6:15 ` Krishna Chaitanya 2014-01-23 6:37 ` Liu, Bopeng @ 2014-01-23 6:44 ` zhuyj 2014-01-23 8:23 ` Emmanuel Grumbach 1 sibling, 1 reply; 28+ messages in thread From: zhuyj @ 2014-01-23 6:44 UTC (permalink / raw) To: Krishna Chaitanya, Liu, Bopeng; +Cc: linux-wireless On 01/23/2014 02:15 PM, Krishna Chaitanya wrote: > hostapd -dd -B /etc/hostapd.conf root@wind-desktop:~# hostapd -dd -B /etc/hostapd.conf random: Trying to read entropy from /dev/random Configuration file: /etc/hostapd.conf ctrl_interface_group=0 nl80211: interface wlan0 in phy phy0 rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 nl80211: Using driver-based off-channel TX nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress) nl80211: Register frame match - hexdump(len=2): 04 0a nl80211: Failed to register Action frame processing - ignore for now nl80211: Add own interface ifindex 3 nl80211: Set mode ifindex 3 iftype 3 (AP) nl80211: Create interface iftype 6 (MONITOR) nl80211: New interface mon.wlan0 created: ifindex=4 nl80211: Add own interface ifindex 4 BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) nl80211: Regulatory information - country=00 nl80211: 2402-2472 @ 40 MHz nl80211: 2457-2482 @ 40 MHz nl80211: 2474-2494 @ 20 MHz nl80211: 5170-5250 @ 40 MHz nl80211: 5735-5835 @ 40 MHz nl80211: Added 802.11b mode based on 802.11g information Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm wlan0: IEEE 802.11 Configured channel (1) not found from the channel list of current mode (2) IEEE 802.11a wlan0: IEEE 802.11 Hardware does not support configured channel Could not select hw_mode and channel. (-4) wlan0: Unable to setup interface. Flushing old station entries Deauthenticate all stations rmdir[ctrl_interface]: No such file or directory nl80211: Remove interface ifindex=4 netlink: Operstate: linkmode=0, operstate=6 nl80211: Set mode ifindex 3 iftype 2 (STATION) root@wind-desktop:~# root@wind-desktop:~# hostapd -v hostapd v1.0 User space daemon for IEEE 802.11 AP management, IEEE 802.1X/WPA/WPA2/EAP/RADIUS Authenticator Copyright (c) 2002-2012, Jouni Malinen <j@w1.fi> and contributors ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-23 6:44 ` zhuyj @ 2014-01-23 8:23 ` Emmanuel Grumbach 2014-01-23 8:36 ` Liu, Bopeng 2014-01-23 8:50 ` zhuyj 0 siblings, 2 replies; 28+ messages in thread From: Emmanuel Grumbach @ 2014-01-23 8:23 UTC (permalink / raw) To: zhuyj; +Cc: Krishna Chaitanya, Liu, Bopeng, linux-wireless On Thu, Jan 23, 2014 at 8:44 AM, zhuyj <zyjzyj2000@gmail.com> wrote: > On 01/23/2014 02:15 PM, Krishna Chaitanya wrote: >> >> hostapd -dd -B /etc/hostapd.conf > > root@wind-desktop:~# hostapd -dd -B /etc/hostapd.conf > > random: Trying to read entropy from /dev/random > Configuration file: /etc/hostapd.conf > ctrl_interface_group=0 > nl80211: interface wlan0 in phy phy0 > rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 > nl80211: Using driver-based off-channel TX > nl80211: Register frame command failed (type=208): ret=-114 (Operation > already in progress) > nl80211: Register frame match - hexdump(len=2): 04 0a > nl80211: Failed to register Action frame processing - ignore for now > nl80211: Add own interface ifindex 3 > nl80211: Set mode ifindex 3 iftype 3 (AP) > nl80211: Create interface iftype 6 (MONITOR) > nl80211: New interface mon.wlan0 created: ifindex=4 > nl80211: Add own interface ifindex 4 > BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) > nl80211: Regulatory information - country=00 > nl80211: 2402-2472 @ 40 MHz > nl80211: 2457-2482 @ 40 MHz > nl80211: 2474-2494 @ 20 MHz > nl80211: 5170-5250 @ 40 MHz > nl80211: 5735-5835 @ 40 MHz > nl80211: Added 802.11b mode based on 802.11g information > Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm > wlan0: IEEE 802.11 Configured channel (1) not found from the channel list of > current mode (2) IEEE 802.11a > > wlan0: IEEE 802.11 Hardware does not support configured channel > Could not select hw_mode and channel. (-4) > wlan0: Unable to setup interface. > Flushing old station entries > Deauthenticate all stations > rmdir[ctrl_interface]: No such file or directory > nl80211: Remove interface ifindex=4 > netlink: Operstate: linkmode=0, operstate=6 > nl80211: Set mode ifindex 3 iftype 2 (STATION) > root@wind-desktop:~# > > > root@wind-desktop:~# hostapd -v I think you have the answer to your question, don't you? ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 8:23 ` Emmanuel Grumbach @ 2014-01-23 8:36 ` Liu, Bopeng 2014-01-23 8:41 ` Liu, Bopeng 2014-01-23 8:50 ` zhuyj 1 sibling, 1 reply; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 8:36 UTC (permalink / raw) To: Emmanuel Grumbach, zhuyj; +Cc: Krishna Chaitanya, linux-wireless Not yet,please tell me..... Please,thanks very much. Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Emmanuel Grumbach [egrumbach@gmail.com] Sent: Thursday, January 23, 2014 4:23 PM To: zhuyj Cc: Krishna Chaitanya; Liu, Bopeng; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 8:44 AM, zhuyj <zyjzyj2000@gmail.com> wrote: > On 01/23/2014 02:15 PM, Krishna Chaitanya wrote: >> >> hostapd -dd -B /etc/hostapd.conf > > root@wind-desktop:~# hostapd -dd -B /etc/hostapd.conf > > random: Trying to read entropy from /dev/random > Configuration file: /etc/hostapd.conf > ctrl_interface_group=0 > nl80211: interface wlan0 in phy phy0 > rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 > nl80211: Using driver-based off-channel TX > nl80211: Register frame command failed (type=208): ret=-114 (Operation > already in progress) > nl80211: Register frame match - hexdump(len=2): 04 0a > nl80211: Failed to register Action frame processing - ignore for now > nl80211: Add own interface ifindex 3 > nl80211: Set mode ifindex 3 iftype 3 (AP) > nl80211: Create interface iftype 6 (MONITOR) > nl80211: New interface mon.wlan0 created: ifindex=4 > nl80211: Add own interface ifindex 4 > BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) > nl80211: Regulatory information - country=00 > nl80211: 2402-2472 @ 40 MHz > nl80211: 2457-2482 @ 40 MHz > nl80211: 2474-2494 @ 20 MHz > nl80211: 5170-5250 @ 40 MHz > nl80211: 5735-5835 @ 40 MHz > nl80211: Added 802.11b mode based on 802.11g information > Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm > wlan0: IEEE 802.11 Configured channel (1) not found from the channel list of > current mode (2) IEEE 802.11a > > wlan0: IEEE 802.11 Hardware does not support configured channel > Could not select hw_mode and channel. (-4) > wlan0: Unable to setup interface. > Flushing old station entries > Deauthenticate all stations > rmdir[ctrl_interface]: No such file or directory > nl80211: Remove interface ifindex=4 > netlink: Operstate: linkmode=0, operstate=6 > nl80211: Set mode ifindex 3 iftype 2 (STATION) > root@wind-desktop:~# > > > root@wind-desktop:~# hostapd -v I think you have the answer to your question, don't you? ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 8:36 ` Liu, Bopeng @ 2014-01-23 8:41 ` Liu, Bopeng 0 siblings, 0 replies; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 8:41 UTC (permalink / raw) To: Emmanuel Grumbach, zhuyj; +Cc: Krishna Chaitanya, linux-wireless Thanks, but after I run the command: iwconfig wlan0 it shows the wlan0 supports a b g n mode. Can you give me a explanation on it? Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: linux-wireless-owner@vger.kernel.org [linux-wireless-owner@vger.kernel.org] on behalf of Liu, Bopeng [Bopeng.Liu@windriver.com] Sent: Thursday, January 23, 2014 4:36 PM To: Emmanuel Grumbach; zhuyj Cc: Krishna Chaitanya; linux-wireless Subject: RE: 802.11a is supported in AP mode or not? Not yet,please tell me..... Please,thanks very much. Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Emmanuel Grumbach [egrumbach@gmail.com] Sent: Thursday, January 23, 2014 4:23 PM To: zhuyj Cc: Krishna Chaitanya; Liu, Bopeng; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 8:44 AM, zhuyj <zyjzyj2000@gmail.com> wrote: > On 01/23/2014 02:15 PM, Krishna Chaitanya wrote: >> >> hostapd -dd -B /etc/hostapd.conf > > root@wind-desktop:~# hostapd -dd -B /etc/hostapd.conf > > random: Trying to read entropy from /dev/random > Configuration file: /etc/hostapd.conf > ctrl_interface_group=0 > nl80211: interface wlan0 in phy phy0 > rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 > nl80211: Using driver-based off-channel TX > nl80211: Register frame command failed (type=208): ret=-114 (Operation > already in progress) > nl80211: Register frame match - hexdump(len=2): 04 0a > nl80211: Failed to register Action frame processing - ignore for now > nl80211: Add own interface ifindex 3 > nl80211: Set mode ifindex 3 iftype 3 (AP) > nl80211: Create interface iftype 6 (MONITOR) > nl80211: New interface mon.wlan0 created: ifindex=4 > nl80211: Add own interface ifindex 4 > BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) > nl80211: Regulatory information - country=00 > nl80211: 2402-2472 @ 40 MHz > nl80211: 2457-2482 @ 40 MHz > nl80211: 2474-2494 @ 20 MHz > nl80211: 5170-5250 @ 40 MHz > nl80211: 5735-5835 @ 40 MHz > nl80211: Added 802.11b mode based on 802.11g information > Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm > Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm > wlan0: IEEE 802.11 Configured channel (1) not found from the channel list of > current mode (2) IEEE 802.11a > > wlan0: IEEE 802.11 Hardware does not support configured channel > Could not select hw_mode and channel. (-4) > wlan0: Unable to setup interface. > Flushing old station entries > Deauthenticate all stations > rmdir[ctrl_interface]: No such file or directory > nl80211: Remove interface ifindex=4 > netlink: Operstate: linkmode=0, operstate=6 > nl80211: Set mode ifindex 3 iftype 2 (STATION) > root@wind-desktop:~# > > > root@wind-desktop:~# hostapd -v I think you have the answer to your question, don't you? -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-23 8:23 ` Emmanuel Grumbach 2014-01-23 8:36 ` Liu, Bopeng @ 2014-01-23 8:50 ` zhuyj 2014-01-23 8:57 ` Krishna Chaitanya 1 sibling, 1 reply; 28+ messages in thread From: zhuyj @ 2014-01-23 8:50 UTC (permalink / raw) To: Emmanuel Grumbach; +Cc: Krishna Chaitanya, Liu, Bopeng, linux-wireless, zhuyj On 01/23/2014 04:23 PM, Emmanuel Grumbach wrote: > On Thu, Jan 23, 2014 at 8:44 AM, zhuyj <zyjzyj2000@gmail.com> wrote: >> On 01/23/2014 02:15 PM, Krishna Chaitanya wrote: >>> hostapd -dd -B /etc/hostapd.conf >> root@wind-desktop:~# hostapd -dd -B /etc/hostapd.conf >> >> random: Trying to read entropy from /dev/random >> Configuration file: /etc/hostapd.conf >> ctrl_interface_group=0 >> nl80211: interface wlan0 in phy phy0 >> rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 >> nl80211: Using driver-based off-channel TX >> nl80211: Register frame command failed (type=208): ret=-114 (Operation >> already in progress) >> nl80211: Register frame match - hexdump(len=2): 04 0a >> nl80211: Failed to register Action frame processing - ignore for now >> nl80211: Add own interface ifindex 3 >> nl80211: Set mode ifindex 3 iftype 3 (AP) >> nl80211: Create interface iftype 6 (MONITOR) >> nl80211: New interface mon.wlan0 created: ifindex=4 >> nl80211: Add own interface ifindex 4 >> BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) >> nl80211: Regulatory information - country=00 >> nl80211: 2402-2472 @ 40 MHz >> nl80211: 2457-2482 @ 40 MHz >> nl80211: 2474-2494 @ 20 MHz >> nl80211: 5170-5250 @ 40 MHz >> nl80211: 5735-5835 @ 40 MHz >> nl80211: Added 802.11b mode based on 802.11g information >> Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm >> Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm >> Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm >> wlan0: IEEE 802.11 Configured channel (1) not found from the channel list of >> current mode (2) IEEE 802.11a >> >> wlan0: IEEE 802.11 Hardware does not support configured channel >> Could not select hw_mode and channel. (-4) >> wlan0: Unable to setup interface. >> Flushing old station entries >> Deauthenticate all stations >> rmdir[ctrl_interface]: No such file or directory >> nl80211: Remove interface ifindex=4 >> netlink: Operstate: linkmode=0, operstate=6 >> nl80211: Set mode ifindex 3 iftype 2 (STATION) >> root@wind-desktop:~# >> >> >> root@wind-desktop:~# hostapd -v > I think you have the answer to your question, don't you? > Yeah, maybe the hardware can support 802.11a, but the driver does not support 802.11a? ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-23 8:50 ` zhuyj @ 2014-01-23 8:57 ` Krishna Chaitanya 2014-01-23 8:59 ` Liu, Bopeng 0 siblings, 1 reply; 28+ messages in thread From: Krishna Chaitanya @ 2014-01-23 8:57 UTC (permalink / raw) To: zhuyj; +Cc: Emmanuel Grumbach, Liu, Bopeng, linux-wireless On Thu, Jan 23, 2014 at 2:20 PM, zhuyj <zyjzyj2000@gmail.com> wrote: > On 01/23/2014 04:23 PM, Emmanuel Grumbach wrote: >> >> On Thu, Jan 23, 2014 at 8:44 AM, zhuyj <zyjzyj2000@gmail.com> wrote: >>> >>> On 01/23/2014 02:15 PM, Krishna Chaitanya wrote: >>>> >>>> hostapd -dd -B /etc/hostapd.conf >>> >>> root@wind-desktop:~# hostapd -dd -B /etc/hostapd.conf >>> >>> random: Trying to read entropy from /dev/random >>> Configuration file: /etc/hostapd.conf >>> ctrl_interface_group=0 >>> nl80211: interface wlan0 in phy phy0 >>> rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 >>> nl80211: Using driver-based off-channel TX >>> nl80211: Register frame command failed (type=208): ret=-114 (Operation >>> already in progress) >>> nl80211: Register frame match - hexdump(len=2): 04 0a >>> nl80211: Failed to register Action frame processing - ignore for now >>> nl80211: Add own interface ifindex 3 >>> nl80211: Set mode ifindex 3 iftype 3 (AP) >>> nl80211: Create interface iftype 6 (MONITOR) >>> nl80211: New interface mon.wlan0 created: ifindex=4 >>> nl80211: Add own interface ifindex 4 >>> BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) >>> nl80211: Regulatory information - country=00 >>> nl80211: 2402-2472 @ 40 MHz >>> nl80211: 2457-2482 @ 40 MHz >>> nl80211: 2474-2494 @ 20 MHz >>> nl80211: 5170-5250 @ 40 MHz >>> nl80211: 5735-5835 @ 40 MHz >>> nl80211: Added 802.11b mode based on 802.11g information >>> Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm >>> wlan0: IEEE 802.11 Configured channel (1) not found from the channel list >>> of >>> current mode (2) IEEE 802.11a >>> >>> wlan0: IEEE 802.11 Hardware does not support configured channel >>> Could not select hw_mode and channel. (-4) >>> wlan0: Unable to setup interface. >>> Flushing old station entries >>> Deauthenticate all stations >>> rmdir[ctrl_interface]: No such file or directory >>> nl80211: Remove interface ifindex=4 >>> netlink: Operstate: linkmode=0, operstate=6 >>> nl80211: Set mode ifindex 3 iftype 2 (STATION) >>> root@wind-desktop:~# >>> >>> >>> root@wind-desktop:~# hostapd -v >> >> I think you have the answer to your question, don't you? >> > Yeah, maybe the hardware can support 802.11a, but the driver does not > support 802.11a? All the 5GHz channels are either disabled (or) passive-scan, so AP operation will not work. (from iw phy) Why don't you try with hostapd from git (1.0 is old)? It has changes to handle regulatory and channel list update properly. ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 8:57 ` Krishna Chaitanya @ 2014-01-23 8:59 ` Liu, Bopeng 2014-01-23 9:04 ` Krishna Chaitanya 0 siblings, 1 reply; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 8:59 UTC (permalink / raw) To: Krishna Chaitanya, zhuyj; +Cc: Emmanuel Grumbach, linux-wireless Is there any method to set the 5GHz channels be able? Please show me the command...:) Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Krishna Chaitanya [chaitanya.mgit@gmail.com] Sent: Thursday, January 23, 2014 4:57 PM To: zhuyj Cc: Emmanuel Grumbach; Liu, Bopeng; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 2:20 PM, zhuyj <zyjzyj2000@gmail.com> wrote: > On 01/23/2014 04:23 PM, Emmanuel Grumbach wrote: >> >> On Thu, Jan 23, 2014 at 8:44 AM, zhuyj <zyjzyj2000@gmail.com> wrote: >>> >>> On 01/23/2014 02:15 PM, Krishna Chaitanya wrote: >>>> >>>> hostapd -dd -B /etc/hostapd.conf >>> >>> root@wind-desktop:~# hostapd -dd -B /etc/hostapd.conf >>> >>> random: Trying to read entropy from /dev/random >>> Configuration file: /etc/hostapd.conf >>> ctrl_interface_group=0 >>> nl80211: interface wlan0 in phy phy0 >>> rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 >>> nl80211: Using driver-based off-channel TX >>> nl80211: Register frame command failed (type=208): ret=-114 (Operation >>> already in progress) >>> nl80211: Register frame match - hexdump(len=2): 04 0a >>> nl80211: Failed to register Action frame processing - ignore for now >>> nl80211: Add own interface ifindex 3 >>> nl80211: Set mode ifindex 3 iftype 3 (AP) >>> nl80211: Create interface iftype 6 (MONITOR) >>> nl80211: New interface mon.wlan0 created: ifindex=4 >>> nl80211: Add own interface ifindex 4 >>> BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) >>> nl80211: Regulatory information - country=00 >>> nl80211: 2402-2472 @ 40 MHz >>> nl80211: 2457-2482 @ 40 MHz >>> nl80211: 2474-2494 @ 20 MHz >>> nl80211: 5170-5250 @ 40 MHz >>> nl80211: 5735-5835 @ 40 MHz >>> nl80211: Added 802.11b mode based on 802.11g information >>> Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm >>> Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm >>> Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm >>> wlan0: IEEE 802.11 Configured channel (1) not found from the channel list >>> of >>> current mode (2) IEEE 802.11a >>> >>> wlan0: IEEE 802.11 Hardware does not support configured channel >>> Could not select hw_mode and channel. (-4) >>> wlan0: Unable to setup interface. >>> Flushing old station entries >>> Deauthenticate all stations >>> rmdir[ctrl_interface]: No such file or directory >>> nl80211: Remove interface ifindex=4 >>> netlink: Operstate: linkmode=0, operstate=6 >>> nl80211: Set mode ifindex 3 iftype 2 (STATION) >>> root@wind-desktop:~# >>> >>> >>> root@wind-desktop:~# hostapd -v >> >> I think you have the answer to your question, don't you? >> > Yeah, maybe the hardware can support 802.11a, but the driver does not > support 802.11a? All the 5GHz channels are either disabled (or) passive-scan, so AP operation will not work. (from iw phy) Why don't you try with hostapd from git (1.0 is old)? It has changes to handle regulatory and channel list update properly. ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-23 8:59 ` Liu, Bopeng @ 2014-01-23 9:04 ` Krishna Chaitanya 2014-01-23 9:07 ` Liu, Bopeng 0 siblings, 1 reply; 28+ messages in thread From: Krishna Chaitanya @ 2014-01-23 9:04 UTC (permalink / raw) To: Liu, Bopeng; +Cc: zhuyj, Emmanuel Grumbach, linux-wireless On Thu, Jan 23, 2014 at 2:29 PM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > Is there any method to set the 5GHz channels be able? > > Please show me the command...:) No it doesn't work that way, based on regulatory info and HW capability the framework will decide that. Lets give it a try with latest hostapd from git and see. ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 9:04 ` Krishna Chaitanya @ 2014-01-23 9:07 ` Liu, Bopeng 2014-01-23 9:20 ` Liu, Bopeng 0 siblings, 1 reply; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 9:07 UTC (permalink / raw) To: Krishna Chaitanya; +Cc: zhuyj, Emmanuel Grumbach, linux-wireless By using latest hostapd, version, not works as well. Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Krishna Chaitanya [chaitanya.mgit@gmail.com] Sent: Thursday, January 23, 2014 5:04 PM To: Liu, Bopeng Cc: zhuyj; Emmanuel Grumbach; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 2:29 PM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > Is there any method to set the 5GHz channels be able? > > Please show me the command...:) No it doesn't work that way, based on regulatory info and HW capability the framework will decide that. Lets give it a try with latest hostapd from git and see. ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 9:07 ` Liu, Bopeng @ 2014-01-23 9:20 ` Liu, Bopeng 2014-01-23 9:21 ` Liu, Bopeng 0 siblings, 1 reply; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 9:20 UTC (permalink / raw) To: Krishna Chaitanya; +Cc: zhuyj, Emmanuel Grumbach, linux-wireless So,it that mean: there is no way to fix this problem by modify the kernel and driver codes? Though #iwconfig wlan0 shows there is modes a ? Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: linux-wireless-owner@vger.kernel.org [linux-wireless-owner@vger.kernel.org] on behalf of Liu, Bopeng [Bopeng.Liu@windriver.com] Sent: Thursday, January 23, 2014 5:07 PM To: Krishna Chaitanya Cc: zhuyj; Emmanuel Grumbach; linux-wireless Subject: RE: 802.11a is supported in AP mode or not? By using latest hostapd, version, not works as well. Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Krishna Chaitanya [chaitanya.mgit@gmail.com] Sent: Thursday, January 23, 2014 5:04 PM To: Liu, Bopeng Cc: zhuyj; Emmanuel Grumbach; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 2:29 PM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > Is there any method to set the 5GHz channels be able? > > Please show me the command...:) No it doesn't work that way, based on regulatory info and HW capability the framework will decide that. Lets give it a try with latest hostapd from git and see. -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 9:20 ` Liu, Bopeng @ 2014-01-23 9:21 ` Liu, Bopeng 2014-01-23 9:27 ` Emmanuel Grumbach 0 siblings, 1 reply; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 9:21 UTC (permalink / raw) To: Krishna Chaitanya; +Cc: zhuyj, Emmanuel Grumbach, linux-wireless So,it that mean: there is no way to fix this problem by modify the kernel and driver codes? Though #iwconfig wlan0 shows there is modes a ? iwconfig wlan0 wlan0 IEEE 802.11abgn ESSID:"IDPDK-169c" Mode:Managed Frequency:2.462 GHz Access Point: A0:88:B4:1E:16:9C Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:14 Missed beacon:0 Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: linux-wireless-owner@vger.kernel.org [linux-wireless-owner@vger.kernel.org] on behalf of Liu, Bopeng [Bopeng.Liu@windriver.com] Sent: Thursday, January 23, 2014 5:07 PM To: Krishna Chaitanya Cc: zhuyj; Emmanuel Grumbach; linux-wireless Subject: RE: 802.11a is supported in AP mode or not? By using latest hostapd, version, not works as well. Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Krishna Chaitanya [chaitanya.mgit@gmail.com] Sent: Thursday, January 23, 2014 5:04 PM To: Liu, Bopeng Cc: zhuyj; Emmanuel Grumbach; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 2:29 PM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > Is there any method to set the 5GHz channels be able? > > Please show me the command...:) No it doesn't work that way, based on regulatory info and HW capability the framework will decide that. Lets give it a try with latest hostapd from git and see. -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-23 9:21 ` Liu, Bopeng @ 2014-01-23 9:27 ` Emmanuel Grumbach 2014-01-23 9:29 ` Krishna Chaitanya 2014-01-24 6:26 ` Liu, Bopeng 0 siblings, 2 replies; 28+ messages in thread From: Emmanuel Grumbach @ 2014-01-23 9:27 UTC (permalink / raw) To: Liu, Bopeng; +Cc: Krishna Chaitanya, zhuyj, linux-wireless On Thu, Jan 23, 2014 at 11:21 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > > > So,it that mean: there is no way to fix this problem by modify the kernel and driver codes? Yes > > Though #iwconfig wlan0 shows there is modes a ? In client mode - not in AP mode > > iwconfig wlan0 > wlan0 IEEE 802.11abgn ESSID:"IDPDK-169c" > Mode:Managed Frequency:2.462 GHz Access Point: A0:88:B4:1E:16:9C > Bit Rate=1 Mb/s Tx-Power=15 dBm > Retry long limit:7 RTS thr:off Fragment thr:off > Encryption key:off > Power Management:off > Link Quality=60/70 Signal level=-50 dBm > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:0 Invalid misc:14 Missed beacon:0 > > ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-23 9:27 ` Emmanuel Grumbach @ 2014-01-23 9:29 ` Krishna Chaitanya 2014-01-23 9:34 ` Liu, Bopeng 2014-01-24 6:26 ` Liu, Bopeng 1 sibling, 1 reply; 28+ messages in thread From: Krishna Chaitanya @ 2014-01-23 9:29 UTC (permalink / raw) To: Emmanuel Grumbach; +Cc: Liu, Bopeng, zhuyj, linux-wireless On Thu, Jan 23, 2014 at 2:57 PM, Emmanuel Grumbach <egrumbach@gmail.com> wrote: > On Thu, Jan 23, 2014 at 11:21 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: >> >> >> So,it that mean: there is no way to fix this problem by modify the kernel and driver codes? > Yes > >> >> Though #iwconfig wlan0 shows there is modes a ? > > In client mode - not in AP mode >> Well in Us channel 149/36 is a valid channel for AP operation. So ideally it should work? Is there any specific feature blocking such in iwlwifi? can you try building iwlwifi with CONFIG_IWLWIFI_DEBUG from make menuconfig? It prints out the reg rules it read from eeprom? Also please post the full dmesg. >> iwconfig wlan0 >> wlan0 IEEE 802.11abgn ESSID:"IDPDK-169c" >> Mode:Managed Frequency:2.462 GHz Access Point: A0:88:B4:1E:16:9C >> Bit Rate=1 Mb/s Tx-Power=15 dBm >> Retry long limit:7 RTS thr:off Fragment thr:off >> Encryption key:off >> Power Management:off >> Link Quality=60/70 Signal level=-50 dBm >> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 >> Tx excessive retries:0 Invalid misc:14 Missed beacon:0 >> ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 9:29 ` Krishna Chaitanya @ 2014-01-23 9:34 ` Liu, Bopeng 2014-01-23 9:36 ` Liu, Bopeng 2014-01-23 9:49 ` Emmanuel Grumbach 0 siblings, 2 replies; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 9:34 UTC (permalink / raw) To: Krishna Chaitanya, Emmanuel Grumbach; +Cc: zhuyj, linux-wireless But very pity, when running on the AP mode:wlan0 IEEE 802.11abgn is the same.... ~# iwconfig wlan0 wlan0 IEEE 802.11abgn Mode:Master Frequency:2.412 GHz Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Krishna Chaitanya [chaitanya.mgit@gmail.com] Sent: Thursday, January 23, 2014 5:29 PM To: Emmanuel Grumbach Cc: Liu, Bopeng; zhuyj; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 2:57 PM, Emmanuel Grumbach <egrumbach@gmail.com> wrote: > On Thu, Jan 23, 2014 at 11:21 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: >> >> >> So,it that mean: there is no way to fix this problem by modify the kernel and driver codes? > Yes > >> >> Though #iwconfig wlan0 shows there is modes a ? > > In client mode - not in AP mode >> Well in Us channel 149/36 is a valid channel for AP operation. So ideally it should work? Is there any specific feature blocking such in iwlwifi? can you try building iwlwifi with CONFIG_IWLWIFI_DEBUG from make menuconfig? It prints out the reg rules it read from eeprom? Also please post the full dmesg. >> iwconfig wlan0 >> wlan0 IEEE 802.11abgn ESSID:"IDPDK-169c" >> Mode:Managed Frequency:2.462 GHz Access Point: A0:88:B4:1E:16:9C >> Bit Rate=1 Mb/s Tx-Power=15 dBm >> Retry long limit:7 RTS thr:off Fragment thr:off >> Encryption key:off >> Power Management:off >> Link Quality=60/70 Signal level=-50 dBm >> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 >> Tx excessive retries:0 Invalid misc:14 Missed beacon:0 >> ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 9:34 ` Liu, Bopeng @ 2014-01-23 9:36 ` Liu, Bopeng 2014-01-23 9:49 ` Emmanuel Grumbach 1 sibling, 0 replies; 28+ messages in thread From: Liu, Bopeng @ 2014-01-23 9:36 UTC (permalink / raw) To: Krishna Chaitanya, Emmanuel Grumbach; +Cc: zhuyj, linux-wireless Well in Us channel 149/36 is a valid channel for AP operation. Doesn't work as well, we are in Main land China..... Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: linux-wireless-owner@vger.kernel.org [linux-wireless-owner@vger.kernel.org] on behalf of Liu, Bopeng [Bopeng.Liu@windriver.com] Sent: Thursday, January 23, 2014 5:34 PM To: Krishna Chaitanya; Emmanuel Grumbach Cc: zhuyj; linux-wireless Subject: RE: 802.11a is supported in AP mode or not? But very pity, when running on the AP mode:wlan0 IEEE 802.11abgn is the same.... ~# iwconfig wlan0 wlan0 IEEE 802.11abgn Mode:Master Frequency:2.412 GHz Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Krishna Chaitanya [chaitanya.mgit@gmail.com] Sent: Thursday, January 23, 2014 5:29 PM To: Emmanuel Grumbach Cc: Liu, Bopeng; zhuyj; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 2:57 PM, Emmanuel Grumbach <egrumbach@gmail.com> wrote: > On Thu, Jan 23, 2014 at 11:21 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: >> >> >> So,it that mean: there is no way to fix this problem by modify the kernel and driver codes? > Yes > >> >> Though #iwconfig wlan0 shows there is modes a ? > > In client mode - not in AP mode >> Well in Us channel 149/36 is a valid channel for AP operation. So ideally it should work? Is there any specific feature blocking such in iwlwifi? can you try building iwlwifi with CONFIG_IWLWIFI_DEBUG from make menuconfig? It prints out the reg rules it read from eeprom? Also please post the full dmesg. >> iwconfig wlan0 >> wlan0 IEEE 802.11abgn ESSID:"IDPDK-169c" >> Mode:Managed Frequency:2.462 GHz Access Point: A0:88:B4:1E:16:9C >> Bit Rate=1 Mb/s Tx-Power=15 dBm >> Retry long limit:7 RTS thr:off Fragment thr:off >> Encryption key:off >> Power Management:off >> Link Quality=60/70 Signal level=-50 dBm >> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 >> Tx excessive retries:0 Invalid misc:14 Missed beacon:0 >> -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-23 9:34 ` Liu, Bopeng 2014-01-23 9:36 ` Liu, Bopeng @ 2014-01-23 9:49 ` Emmanuel Grumbach 2014-01-24 5:27 ` Liu, Bopeng 1 sibling, 1 reply; 28+ messages in thread From: Emmanuel Grumbach @ 2014-01-23 9:49 UTC (permalink / raw) To: Liu, Bopeng; +Cc: Krishna Chaitanya, zhuyj, linux-wireless On Thu, Jan 23, 2014 at 11:34 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > But very pity, when running on the AP mode:wlan0 IEEE 802.11abgn is the same.... > > ~# iwconfig wlan0 > wlan0 IEEE 802.11abgn Mode:Master Frequency:2.412 GHz Tx-Power=15 dBm > Retry long limit:7 RTS thr:off Fragment thr:off > Power Management:off > cool - just send a patch to fix iwconfig, but this tool is ancient and I doubt anybody even cares. ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 9:49 ` Emmanuel Grumbach @ 2014-01-24 5:27 ` Liu, Bopeng 2014-01-27 21:21 ` Anand Moon 0 siblings, 1 reply; 28+ messages in thread From: Liu, Bopeng @ 2014-01-24 5:27 UTC (permalink / raw) To: Emmanuel Grumbach; +Cc: Krishna Chaitanya, zhuyj, linux-wireless I just check the chip 6205's spec. it said it supports the SoftAP with Mode A, who can tell me what is the soft AP? Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Emmanuel Grumbach [egrumbach@gmail.com] Sent: Thursday, January 23, 2014 5:49 PM To: Liu, Bopeng Cc: Krishna Chaitanya; zhuyj; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 11:34 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > But very pity, when running on the AP mode:wlan0 IEEE 802.11abgn is the same.... > > ~# iwconfig wlan0 > wlan0 IEEE 802.11abgn Mode:Master Frequency:2.412 GHz Tx-Power=15 dBm > Retry long limit:7 RTS thr:off Fragment thr:off > Power Management:off > cool - just send a patch to fix iwconfig, but this tool is ancient and I doubt anybody even cares. ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-24 5:27 ` Liu, Bopeng @ 2014-01-27 21:21 ` Anand Moon 2014-01-27 21:59 ` Anand Moon 0 siblings, 1 reply; 28+ messages in thread From: Anand Moon @ 2014-01-27 21:21 UTC (permalink / raw) To: Liu, Bopeng, Emmanuel Grumbach; +Cc: Krishna Chaitanya, zhuyj, linux-wireless Hi All, Prerequisite: iw list If there is 'AP' in the list of "Supported interface modes" your device will support the Access Point mode with hostapd. Second if the interface is supporting 2.4 GHz then you cannot get the support for 802.11a which supports 5 GHz. Change the hw_mode=a to hw_mode=g To configure AP:..... Bring the interface down Set the interface to master mode #ifconfig wlan0 down #iw dev wlan0 set type managed #ifconfig wlan0 up # hostapd -B /tmp/hostapd.conf -dd It worked for me, I was able to connect to this AP. If the interface support dual band, then you need to set the freq to 5Ghz of the interface. -Anand Moon -----BEGIN PGP MESSAGE----- Version: GnuPG v1.4.14 (GNU/Linux) jA0EAwMCYq3dHqTzwcVgyRxC1j+ oLxS8Yw92EIeKln+x3eAWzd7mM/ pUluRo =0RYk -----END PGP MESSAGE----- On Friday, January 24, 2014 1:35 PM, "Liu, Bopeng" <Bopeng.Liu@windriver.com> wrote: I just check the chip 6205's spec. it said it supports the SoftAP with Mode A, who can tell me what is the soft AP? Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Emmanuel Grumbach [egrumbach@gmail.com] Sent: Thursday, January 23, 2014 5:49 PM To: Liu, Bopeng Cc: Krishna Chaitanya; zhuyj; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 11:34 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > But very pity, when running on the AP mode:wlan0 IEEE 802.11abgn is the same.... > > ~# iwconfig wlan0 > wlan0 IEEE 802.11abgn Mode:Master Frequency:2.412 GHz Tx-Power=15 dBm > Retry long limit:7 RTS thr:off Fragment thr:off > Power Management:off > cool - just send a patch to fix iwconfig, but this tool is ancient and I doubt anybody even cares. -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: 802.11a is supported in AP mode or not? 2014-01-27 21:21 ` Anand Moon @ 2014-01-27 21:59 ` Anand Moon 0 siblings, 0 replies; 28+ messages in thread From: Anand Moon @ 2014-01-27 21:59 UTC (permalink / raw) To: Anand Moon, Liu, Bopeng, Emmanuel Grumbach Cc: Krishna Chaitanya, zhuyj, linux-wireless Hi All, If you change the frequency of the interface it should work root@moon-ubuntu:~# ifconfig wlan0 down root@moon-ubuntu:~# iw dev wlan0 set freq 5180 HT20 root@moon-ubuntu:~# iwconfig wlan0 wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Frequency:5.18 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on root@moon-ubuntu:~# ifconfig wlan0 up Now I modified the hostapd.conf hw_mode=a channel=36 It worked for me. -Anand Moon -----BEGIN PGP MESSAGE----- Version: GnuPG v1.4.14 (GNU/Linux) jA0EAwMCYq3dHqTzwcVgyRxC1j+ oLxS8Yw92EIeKln+x3eAWzd7mM/ pUluRo =0RYk -----END PGP MESSAGE----- ^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: 802.11a is supported in AP mode or not? 2014-01-23 9:27 ` Emmanuel Grumbach 2014-01-23 9:29 ` Krishna Chaitanya @ 2014-01-24 6:26 ` Liu, Bopeng 1 sibling, 0 replies; 28+ messages in thread From: Liu, Bopeng @ 2014-01-24 6:26 UTC (permalink / raw) To: Emmanuel Grumbach; +Cc: Krishna Chaitanya, zhuyj, linux-wireless I just check the chip 6205's spec. it said it supports the SoftAP with Mode A, but why the AP in mode A can't be used? Best Regards. -------------------------------------- Bopeng Liu WIND RIVER | China Development Center Phone: 8610-6483-5012 ________________________________________ From: Emmanuel Grumbach [egrumbach@gmail.com] Sent: Thursday, January 23, 2014 5:27 PM To: Liu, Bopeng Cc: Krishna Chaitanya; zhuyj; linux-wireless Subject: Re: 802.11a is supported in AP mode or not? On Thu, Jan 23, 2014 at 11:21 AM, Liu, Bopeng <Bopeng.Liu@windriver.com> wrote: > > > So,it that mean: there is no way to fix this problem by modify the kernel and driver codes? Yes > > Though #iwconfig wlan0 shows there is modes a ? In client mode - not in AP mode > > iwconfig wlan0 > wlan0 IEEE 802.11abgn ESSID:"IDPDK-169c" > Mode:Managed Frequency:2.462 GHz Access Point: A0:88:B4:1E:16:9C > Bit Rate=1 Mb/s Tx-Power=15 dBm > Retry long limit:7 RTS thr:off Fragment thr:off > Encryption key:off > Power Management:off > Link Quality=60/70 Signal level=-50 dBm > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:0 Invalid misc:14 Missed beacon:0 > > ^ permalink raw reply [flat|nested] 28+ messages in thread
end of thread, other threads:[~2014-01-27 21:59 UTC | newest] Thread overview: 28+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2014-01-22 9:50 802.11a is supported in AP mode or not? zhuyj 2014-01-22 10:33 ` zhuyj 2014-01-22 10:47 ` Liu, Bopeng 2014-01-22 14:51 ` Pat Erley 2014-01-22 21:20 ` Krishna Chaitanya 2014-01-23 2:00 ` Liu, Bopeng 2014-01-23 6:15 ` Krishna Chaitanya 2014-01-23 6:37 ` Liu, Bopeng 2014-01-23 6:44 ` zhuyj 2014-01-23 8:23 ` Emmanuel Grumbach 2014-01-23 8:36 ` Liu, Bopeng 2014-01-23 8:41 ` Liu, Bopeng 2014-01-23 8:50 ` zhuyj 2014-01-23 8:57 ` Krishna Chaitanya 2014-01-23 8:59 ` Liu, Bopeng 2014-01-23 9:04 ` Krishna Chaitanya 2014-01-23 9:07 ` Liu, Bopeng 2014-01-23 9:20 ` Liu, Bopeng 2014-01-23 9:21 ` Liu, Bopeng 2014-01-23 9:27 ` Emmanuel Grumbach 2014-01-23 9:29 ` Krishna Chaitanya 2014-01-23 9:34 ` Liu, Bopeng 2014-01-23 9:36 ` Liu, Bopeng 2014-01-23 9:49 ` Emmanuel Grumbach 2014-01-24 5:27 ` Liu, Bopeng 2014-01-27 21:21 ` Anand Moon 2014-01-27 21:59 ` Anand Moon 2014-01-24 6:26 ` Liu, Bopeng
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).