From: Larry Finger <Larry.Finger@lwfinger.net>
To: Jes.Sorensen@redhat.com, linux-wireless@vger.kernel.org
Cc: kvalo@codeaurora.org
Subject: Re: [PATCH 0/1] rtl8xxxu (mac80211) driver for rtl8188[cr]u/rtl8192cu/rtl8723au
Date: Sun, 30 Aug 2015 11:49:32 -0500 [thread overview]
Message-ID: <55E3341C.2010009@lwfinger.net> (raw)
In-Reply-To: <1440883083-32498-1-git-send-email-Jes.Sorensen@redhat.com>
On 08/29/2015 04:18 PM, Jes.Sorensen@redhat.com wrote:
> From: Jes Sorensen <Jes.Sorensen@redhat.com>
>
> Hi,
>
> I finally found some time to work on rtl8xxxu again. Since the
> previously version posted some months ago, I fixed up a number of
> bugs. I also added support for a range of other Realtek based USB
> devices. The driver now supports rtl8723au, rtl8188cu, rtl8188ru, and
> rtl8192cu. It should work on rtl8191cu devices as well.
>
> Per default only devices I have actually tested will be enabled. If
> you are interested in trying it out with other 8188cu/8188ru/819[12]cu
> dongles, you need to enable CONFIG_RTL8XXXU_UNTESTED. Please report
> test results back to me.
>
> Note if you enable this driver, it may clash with CONFIG_RTL8192U,
> CONFIG_R8723AU, and CONFIG_RTL8192CU (rtlwifi). Please pay attention
> to which module you load and/or use modprobe blacklists.
>
> This driver is still work in progress. I have used it as my primary
> driver for the last six months, and I find it to be very stable. It
> seems suitable for mainline inclusion at this point.
Jes,
The Edimax 7811 works on the new driver. The performance is a lot better than I
said in my previous post. Measuring with netperf for 3 second intervals, I get a
maximum RX rate of 33.0 Mbps and a long-term average (750 samples) of 20.8 Mbps.
For TX, the max is 34.5 Mbps and the average is 27.4.
I am still getting one "scheduling while atomic" BUG splat as follows:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616
in_atomic(): 0, irqs_disabled(): 0, pid: 19961, name: kworker/u16:0
INFO: lockdep is turned off.
CPU: 0 PID: 19961 Comm: kworker/u16:0 Tainted: G W O 4.2.0-rc7-wl+ #39
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.20 04/17/2014
Workqueue: phy9 ieee80211_iface_work [mac80211]
ffffffff81a3d470 ffff880102227508 ffffffff8174b6e1 0000000000000000
ffff880224e54b00 ffff880102227538 ffffffff81090117 ffff880102227578
ffffffff81a3d470 0000000000000268 0000000000000000 ffff880102227568
Call Trace:
[<ffffffff8174b6e1>] dump_stack+0x4c/0x6e
[<ffffffff81090117>] ___might_sleep+0x147/0x1f0
[<ffffffff8109020d>] __might_sleep+0x4d/0x90
[<ffffffff81750d88>] mutex_lock_nested+0x38/0x3c0
[<ffffffff814d9a56>] ? __dev_printk+0x46/0x90
[<ffffffffa07a553f>] rtl8723a_h2c_cmd+0x4f/0x180 [rtl8xxxu]
[<ffffffffa07aa977>] rtl8xxxu_bss_info_changed+0x367/0x6b1 [rtl8xxxu]
[<ffffffffa07aa89f>] ? rtl8xxxu_bss_info_changed+0x28f/0x6b1 [rtl8xxxu]
[<ffffffffa055fd84>] ieee80211_bss_info_change_notify+0x104/0x4e0 [mac80211]
[<ffffffffa05f5626>] ieee80211_assoc_success+0x90c/0xa98 [mac80211]
[<ffffffff8116b8ad>] ? irq_work_queue+0x7d/0xa0
[<ffffffff810d26d9>] ? wake_up_klogd+0x39/0x50
[<ffffffff810d28d7>] ? console_unlock+0x1e7/0x510
[<ffffffff810d2def>] ? vprintk_emit+0x1ef/0x540
[<ffffffff810d3299>] ? vprintk_default+0x29/0x40
[<ffffffffa05d311b>] ieee80211_rx_mgmt_assoc_resp+0x15b/0x310 [mac80211]
[<ffffffffa05d48da>] ieee80211_sta_rx_queued_mgmt+0x19a/0x6d0 [mac80211]
[<ffffffff810b8915>] ? cpuacct_charge+0x5/0x1a0
[<ffffffff815e8a91>] ? skb_dequeue+0x21/0x70
[<ffffffff810bca4d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffffa05803b9>] ieee80211_iface_work+0x2d9/0x3e0 [mac80211]
[<ffffffff81082e7e>] ? process_one_work+0x14e/0x7d0
[<ffffffff81082f0f>] process_one_work+0x1df/0x7d0
[<ffffffff81082e7e>] ? process_one_work+0x14e/0x7d0
[<ffffffff8108361a>] worker_thread+0x11a/0x460
[<ffffffff817546bb>] ? _raw_spin_unlock_irqrestore+0x4b/0x60
[<ffffffff81083500>] ? process_one_work+0x7d0/0x7d0
[<ffffffff81089e9f>] kthread+0xef/0x110
[<ffffffff81089db0>] ? kthread_create_on_node+0x220/0x220
[<ffffffff8175530f>] ret_from_fork+0x3f/0x70
[<ffffffff81089db0>] ? kthread_create_on_node+0x220/0x220
wlp0s20u6: associated
This splat happened during the authentication/association phase. At present, the
connection has been up for almost 12 hours without a single drop.
Larry
next prev parent reply other threads:[~2015-08-30 16:49 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-08-29 21:18 [PATCH 0/1] rtl8xxxu (mac80211) driver for rtl8188[cr]u/rtl8192cu/rtl8723au Jes.Sorensen
2015-08-29 21:18 ` [PATCH 1/1] New driver: rtl8xxxu (mac80211) Jes.Sorensen
2015-08-30 4:42 ` Larry Finger
2015-08-30 18:41 ` Jes Sorensen
2015-08-30 21:02 ` Jes Sorensen
2015-08-30 23:51 ` Larry Finger
2015-08-31 2:39 ` Jes Sorensen
2015-08-31 15:45 ` Larry Finger
2015-08-31 23:43 ` Jes Sorensen
2015-09-01 0:16 ` Larry Finger
2015-09-01 4:54 ` Jes Sorensen
2015-09-01 5:17 ` Larry Finger
2015-09-01 5:26 ` Jes Sorensen
2015-08-31 1:06 ` Joe Perches
2015-08-31 13:11 ` Jes Sorensen
2015-08-31 8:19 ` Johannes Berg
2015-08-31 14:48 ` Johannes Berg
2015-08-31 23:42 ` Jes Sorensen
2015-09-01 15:07 ` Johannes Berg
2015-09-03 1:59 ` Jes Sorensen
2015-09-03 2:39 ` Jes Sorensen
2015-09-03 10:17 ` Johannes Berg
2015-09-04 18:24 ` Jes Sorensen
2015-09-04 18:25 ` Johannes Berg
2015-09-05 4:02 ` Sujith Manoharan
2015-09-17 16:46 ` Johannes Berg
2015-10-05 18:49 ` Jes Sorensen
2015-10-05 18:56 ` Johannes Berg
2015-10-05 19:04 ` Jes Sorensen
2015-10-05 19:12 ` Johannes Berg
2015-10-05 19:19 ` Jes Sorensen
2015-10-05 19:20 ` Johannes Berg
2015-10-05 19:53 ` Jes Sorensen
2015-09-03 10:17 ` Johannes Berg
2015-09-04 17:48 ` Jes Sorensen
2015-09-04 18:02 ` Johannes Berg
2015-10-08 16:23 ` Jakub Sitnicki
2015-10-08 19:09 ` Jes Sorensen
2015-10-08 20:33 ` Stefan Lippers-Hollmann
2015-10-08 21:06 ` Jes Sorensen
2015-10-08 21:03 ` Jes Sorensen
2015-10-10 4:17 ` Taehee Yoo
2015-08-30 16:49 ` Larry Finger [this message]
2015-08-30 18:45 ` [PATCH 0/1] rtl8xxxu (mac80211) driver for rtl8188[cr]u/rtl8192cu/rtl8723au Jes Sorensen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55E3341C.2010009@lwfinger.net \
--to=larry.finger@lwfinger.net \
--cc=Jes.Sorensen@redhat.com \
--cc=kvalo@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).