From: Arend van Spriel <arend@broadcom.com>
To: Kalle Valo <kvalo@codeaurora.org>
Cc: kbuild test robot <lkp@intel.com>, <kbuild-all@01.org>,
linux-wireless <linux-wireless@vger.kernel.org>
Subject: Re: [PATCH 01/11] brcmfmac: expose device memory to devcoredump subsystem
Date: Mon, 12 Oct 2015 22:05:37 +0200 [thread overview]
Message-ID: <561C1291.8060607@broadcom.com> (raw)
In-Reply-To: <87wpuspilw.fsf@kamboji.qca.qualcomm.com>
On 10/12/2015 10:59 AM, Kalle Valo wrote:
> kbuild test robot <lkp@intel.com> writes:
>
>> Hi Arend,
>>
>> [auto build test ERROR on next-20151008 -- if it's inappropriate base, please ignore]
>>
>> config: x86_64-randconfig-x011-201540 (attached as .config)
>> reproduce:
>> # save the attached .config to linux build tree
>> make ARCH=x86_64
>>
>> All errors (new ones prefixed by >>):
>>
>> drivers/net/wireless/brcm80211/brcmfmac/debug.c:58:6: error: redefinition of 'brcmf_debugfs_init'
>> void brcmf_debugfs_init(void)
>> ^
>> In file included from drivers/net/wireless/brcm80211/brcmfmac/bus.h:20:0,
>> from drivers/net/wireless/brcm80211/brcmfmac/debug.c:24:
>> drivers/net/wireless/brcm80211/brcmfmac/debug.h:118:20: note: previous definition of 'brcmf_debugfs_init' was here
>> static inline void brcmf_debugfs_init(void)
>> ^
>
> Arend, are the kbuild errors valid? I would guess they are as
> wireless-drivers-next should be in linux-next.
Hi Kalle,
Actually they are not. I am not sure about the build infrastructure, but
the errors above can only occur when CONFIG_BRCMDBG is set, but DEBUG is
not. However, that can not happen as we have following line in
drivers/net/wireless/brcm80211/Makefile:
subdir-ccflags-$(CONFIG_BRCMDBG) += -DDEBUG
Regards,
Arend
next prev parent reply other threads:[~2015-10-12 20:05 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-10-08 18:33 [PATCH 00/11] brcmfmac: cfg80211 callbacks and coredump Arend van Spriel
2015-10-08 18:33 ` [PATCH 01/11] brcmfmac: expose device memory to devcoredump subsystem Arend van Spriel
2015-10-08 18:59 ` kbuild test robot
2015-10-12 8:59 ` Kalle Valo
2015-10-12 20:05 ` Arend van Spriel [this message]
2015-10-14 11:01 ` Kalle Valo
2015-10-14 13:36 ` Arend van Spriel
2015-10-15 10:06 ` Kalle Valo
2015-10-21 7:57 ` [01/11] " Kalle Valo
2015-10-08 18:33 ` [PATCH 02/11] brcmfmac: Fix race condition between USB probe/load and disconnect Arend van Spriel
2015-10-08 18:33 ` [PATCH 03/11] brcmfmac: rename firmware_path to alternative_fw_path Arend van Spriel
2015-10-08 18:33 ` [PATCH 04/11] brcmfmac: remove conversational comment Arend van Spriel
2015-10-08 18:33 ` [PATCH 05/11] brcmfmac: Rework p2p attach, use single method for p2p dev creation Arend van Spriel
2015-10-08 18:33 ` [PATCH 06/11] brcmfmac: Fix station info rate information Arend van Spriel
2015-10-08 18:33 ` [PATCH 07/11] brcmfmac: Add RSSI information to get_station Arend van Spriel
2015-10-08 18:33 ` [PATCH 08/11] brcmfmac: Add dump_station support to cfg80221 ops Arend van Spriel
2015-10-08 18:33 ` [PATCH 09/11] brcmfmac: Move brcmf_c_preinit_dcmds prototype to correct file Arend van Spriel
2015-10-08 18:33 ` [PATCH 10/11] brcmfmac: Remove unused state AP creating Arend van Spriel
2015-10-08 18:33 ` [PATCH 11/11] brcmfmac: Properly set carrier state of netdev Arend van Spriel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=561C1291.8060607@broadcom.com \
--to=arend@broadcom.com \
--cc=kbuild-all@01.org \
--cc=kvalo@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
--cc=lkp@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).