From: Irwan Siajadi <dev.bahamot@yahoo.com>
To: Dan Williams <dcbw@redhat.com>
Cc: linux-wireless@vger.kernel.org
Subject: Re: ath5k: can't browse at all.
Date: Mon, 24 Nov 2008 18:30:56 -0800 (PST) [thread overview]
Message-ID: <630929.9910.qm@web59607.mail.ac4.yahoo.com> (raw)
In-Reply-To: <1227552872.25089.3.camel@localhost.localdomain>
--- On Mon, 11/24/08, Dan Williams <dcbw@redhat.com> wrote:
> From: Dan Williams <dcbw@redhat.com>
> Subject: Re: ath5k: can't browse at all.
> To: "Irwan Siajadi" <dev.bahamot@yahoo.com>
> Cc: linux-wireless@vger.kernel.org
> Date: Monday, November 24, 2008, 6:54 PM
> On Mon, 2008-11-24 at 09:41 -0800, Irwan Siajadi wrote:
> > The AR2425 is able to obtain IP address from the
> router,
> > able to ping with good results, but can't browse
> at all.
> > Below are the info on my setup, if you need more info
> please let me know.
>
> Can you traceroute to some IP, say like 4.2.2.1 or 4.2.2.2?
Trace seems to work fine. I believe this is a driver problem because I can browse normally as soon as I changed it to ndiswrapper.
Tracepath to osnews.com (using ath5k):
1: 192.168.1.2 (192.168.1.2) 0.225ms pmtu 1500
1: home.gateway (192.168.1.254) 1.217ms asymm 101
1: home.gateway (192.168.1.254) 1.181ms asymm 101
2: home.gateway (192.168.1.254) 1.186ms pmtu 1492
2: 125.167.124.1 (125.167.124.1) 112.890ms
3: 125.160.1.165 (125.160.1.165) 117.249ms
4: no reply
5: 203.208.191.81 (203.208.191.81) 513.481ms asymm 12
6: ge-0-1-7-0.sngtp-dr2.ix.singtel.com (203.208.151.181) 648.204ms asymm 12
7: ge-5-0-0-0.sngtp-cr1.ix.singtel.com (203.208.151.149) 629.931ms asymm 13
8: so-2-0-0-0.plapx-cr2.ix.singtel.com (203.208.149.182) 827.446ms asymm 14
9: ge-6-0-0-0.plapx-dr2.ix.singtel.com (203.208.183.166) 770.144ms asymm 15
10: ge6-0-128.ir1.paloalto-ca.us.xo.net (206.111.12.45) 738.330ms asymm 15
11: te-4-0-0.rar3.sanjose-ca.us.xo.net (207.88.12.61) 758.889ms asymm 16
12: te-3-0-0.rar3.la-ca.us.xo.net (207.88.12.62) 770.112ms asymm 20
13: 207.88.14.33.ptr.us.xo.net (207.88.14.33) 976.042ms asymm 18
14: 207.88.14.34.ptr.us.xo.net (207.88.14.34) 814.660ms asymm 19
15: 207.88.185.74.ptr.us.xo.net (207.88.185.74) 548.507ms asymm 23
16: border3.tge3-1-bbnet1.ext1.dal.pnap.net (216.52.191.22) 392.415ms asymm 23
17: te2-1.cer03.dal01.dallas-datacenter.com (216.52.189.30) 400.309ms asymm 20
18: po3.dar02.dal01.dallas-datacenter.com (66.228.118.211) 405.547ms asymm 19
19: po2.fcr02.dal01.dallas-datacenter.com (66.228.118.182) 404.016ms asymm 20
20: osnews.com (74.86.31.159) 406.893ms reached
Resume: pmtu 1492 hops 20 back 44
>
> Dan
>
> > Driver version: compat-wireless-2008-11-24.tar.bz2.
> > Kernel: 2.6.27.4-2mnbcustom (mandriva), compiled with
> mandriva provided
> > ..config but without any WLAN support except
> WIRELESS_EXT.
> > Access point/router is configured to use channel 1
> (2.412GHz).
> >
> > dmesg:
> > "...
> > cfg80211: Using static regulatory domain info
> > cfg80211: Regulatory domain: JP
> > (start_freq - end_freq @ bandwidth),
> (max_antenna_gain, max_eirp)
> > (2402000 KHz - 2494000 KHz @ 40000 KHz),
> (600 mBi, 2000 mBm)
> > (5160000 KHz - 5250000 KHz @ 40000 KHz),
> (600 mBi, 2000 mBm)
> > (5250000 KHz - 5330000 KHz @ 40000 KHz),
> (600 mBi, 2000 mBm)
> > cfg80211: Calling CRDA for country: JP
> > .....
> > ath5k 0000:05:00.0: PCI INT A -> GSI 16 (level,
> low) -> IRQ 16
> > ath5k 0000:05:00.0: setting latency timer to 64
> > ath5k 0000:05:00.0: registered as 'phy0'
> > phy0: Selected rate control algorithm
> 'minstrel'
> > ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY:
> 0x70)
> > .....
> > wlan0: authenticate with AP 00:04:ed:42:60:67
> > wlan0: authenticated
> > wlan0: associate with AP 00:04:ed:42:60:67
> > wlan0: RX AssocResp from 00:04:ed:42:60:67
> (capab=3D0x431 status=3D0 id=3D)
> > wlan0: associated
> > ....."
> >
> > lspci:
> > "05:00.0 Ethernet controller: Atheros
> Communications Inc. AR242x 802.11abg
> > Wireless PCI Express Adapter (rev 01)
> > Subsystem: Device 1a3b:1026
> > Flags: bus master, fast devsel, latency 0,
> IRQ 16
> > Memory at feaf0000 (64-bit,
> non-prefetchable) [size=3D64K]
> > Capabilities: [40] Power Management version
> 2
> > Capabilities: [50] Message Signalled
> Interrupts: Mask- 64bit Queue=3D0/0 Enable-
> > Capabilities: [60] Express Legacy Endpoint,
> MSI 00
> > Capabilities: [90] MSI-X: Enable- Mask-
> TabSize=3D1
> > Capabilities: [100] Advanced Error Reporting
> <?>
> > Capabilities: [140] Virtual Channel
> <?>"
> >
> > TIA,
> > Irwan.
> >
> >
> >
> >
> > --
> > To unsubscribe from this list: send the line
> "unsubscribe linux-wireless" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at
> http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2008-11-25 2:36 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-11-24 17:41 ath5k: can't browse at all Irwan Siajadi
2008-11-24 18:53 ` Pavel Roskin
2008-11-25 2:36 ` Irwan Siajadi
2008-11-25 17:24 ` Irwan Siajadi
2008-11-25 20:02 ` Pavel Roskin
2008-11-30 16:53 ` Irwan Siajadi
2008-12-01 17:11 ` Luis R. Rodriguez
2008-11-24 18:54 ` Dan Williams
2008-11-25 2:30 ` Irwan Siajadi [this message]
-- strict thread matches above, loose matches on Subject: below --
2008-12-02 3:11 Irwan Siajadi
2008-12-01 21:36 ` Luis R. Rodriguez
2008-12-02 7:27 ` Irwan Siajadi
2008-12-02 8:00 ` Luis R. Rodriguez
2008-12-02 13:04 ` Irwan Siajadi
2008-12-07 19:39 ` Irwan Siajadi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=630929.9910.qm@web59607.mail.ac4.yahoo.com \
--to=dev.bahamot@yahoo.com \
--cc=dcbw@redhat.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).