* rtlwifi: RTL8188EE: Unable to connect to Wifi network
@ 2022-11-08 12:49 Paul Menzel
2022-11-08 16:18 ` Paul Menzel
0 siblings, 1 reply; 8+ messages in thread
From: Paul Menzel @ 2022-11-08 12:49 UTC (permalink / raw)
To: Ping-Ke Shih; +Cc: linux-wireless, it+linux-wireless
Dear Linux folks,
Using Debian sid/unstable with Linux 6.1-rc3 [1] on an Intel Haswell
Haier laptop with a RTL8188EE, I am unable to connect to a wireless network.
$ sudo lspci -k -s 08:00.0
08:00.0 Network controller: Realtek Semiconductor Co., Ltd.
RTL8188EE Wireless Network Adapter (rev 01)
Subsystem: AzureWave RTL8188EE Wireless Network Adapter
Kernel driver in use: rtl8188ee
Kernel modules: rtl8188ee
```
[ 262.822320] wlp8s0: authenticate with 6c:f3:7f:10:ae:12
[ 262.822341] wlp8s0: 80 MHz not supported, disabling VHT
[ 262.832384] wlp8s0: send auth to 6c:f3:7f:10:ae:12 (try 1/3)
[ 262.835124] wlp8s0: authenticated
[ 262.839046] wlp8s0: associate with 6c:f3:7f:10:ae:12 (try 1/3)
[ 262.850099] wlp8s0: RX AssocResp from 6c:f3:7f:10:ae:12 (capab=0x421
status=0 aid=1)
[ 262.850331] wlp8s0: associated
[ 262.850925] IPv6: ADDRCONF(NETDEV_CHANGE): wlp8s0: link becomes ready
[…]
[ 307.618423] wlp8s0: deauthenticating from 6c:f3:7f:10:ae:12 by local
choice (Reason: 3=DEAUTH_LEAVING)
```
wpa_supplicant 2:2.10-9+b2 logs:
```
Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: SME: Trying to
authenticate with 6c:f3:7f:10:ae:12 (SSID='MPI Guest' freq=2437 MHz)
Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: Trying to associate
with 6c:f3:7f:10:ae:12 (SSID='MPI Guest' freq=2437 MHz)
Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: Associated with
6c:f3:7f:10:ae:12
Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: CTRL-EVENT-CONNECTED
- Connection to 6c:f3:7f:10:ae:12 completed [id=0 id_str=]
Nov 08 13:29:35 brecht wpa_supplicant[612]: bgscan simple: Failed to
enable signal strength monitoring
Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
Nov 08 13:30:20 brecht wpa_supplicant[612]: wlp8s0:
CTRL-EVENT-DISCONNECTED bssid=6c:f3:7f:10:ae:12 reason=3 locally_generated=1
```
With more debugging verbosity (`-d`) it shows:
```
[…]
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: State: ASSOCIATED
-> COMPLETED
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Radio work
'sme-connect'@0x556b491b5a80 done in 0.026679 seconds
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0:
radio_work_free('sme-connect'@0x556b491b5a80): num_active_works --> 0
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0:
CTRL-EVENT-CONNECTED - Connection to 6c:f3:7f:10:ae:12 completed [id=0
id_str=]
Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Set wlp8s0
operstate 0->1 (UP)
Nov 08 13:42:13 brecht wpa_supplicant[3547]: netlink: Operstate:
ifindex=3 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Signal
strength threshold -70 Short bgscan interval 30 Long bgscan interval 86400
Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Signal monitor
threshold=-70 hysteresis=4
Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Failed to
enable signal strength monitoring
Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Init scan
interval: 86400
Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan: Initialized module
'simple' with parameters '30:-70:86400'
Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Received scan
results (19 BSSes)
Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Scan results
indicate BSS status with 6c:f3:7f:10:ae:12 as associated
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: BSS: Start scan
result update 5
Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: scan result
notification
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Determining shared
radio frequencies (max len 1)
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Shared frequencies
(len=1): completed iteration
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: freq[0]: 2437,
flags=0x1
Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Add operating class 81
Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Channels -
hexdump(len=13): 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d
Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Update channel list
Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: channels:
81:1,2,3,4,5,6,7,8,9,10,11,12,13
Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: cli_channels:
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Cancelling scan request
Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: AC mandatory:
AC_BE=0 AC_BK=0 AC_VI=0 AC_VO=0
Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: U-APSD queues=0x0
Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: Valid WMM
association, WMM AC is enabled
Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
Nov 08 13:42:13 brecht wpa_supplicant[3547]: RTM_NEWLINK: ifi_index=3
ifname=wlp8s0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Drv Event 46
(NL80211_CMD_CONNECT) received for wlp8s0
Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Ignore connect
event (cmd=46) when using userspace SME
Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Drv Event 20
(NL80211_CMD_DEL_STATION) received for wlp8s0
Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Delete station
6c:f3:7f:10:ae:12
Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Drv Event 39
(NL80211_CMD_DEAUTHENTICATE) received for wlp8s0
Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Deauthenticate event
Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: Event DEAUTH (11)
received
Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: Deauthentication
notification
Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: * reason 3
(DEAUTH_LEAVING) locally_generated=1
Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: * address
6c:f3:7f:10:ae:12
Nov 08 13:42:58 brecht wpa_supplicant[3547]: Deauthentication frame
IE(s) - hexdump(len=0): [NULL]
Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0:
CTRL-EVENT-DISCONNECTED bssid=6c:f3:7f:10:ae:12 reason=3 locally_generated=1
```
It’d be really great to get WLAN working on the device.
Kind regards,
Paul
[1]: https://packages.debian.org/experimental/linux-image-6.1.0-0-amd64
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: rtlwifi: RTL8188EE: Unable to connect to Wifi network
2022-11-08 12:49 rtlwifi: RTL8188EE: Unable to connect to Wifi network Paul Menzel
@ 2022-11-08 16:18 ` Paul Menzel
2022-11-08 22:36 ` Larry Finger
2022-11-09 2:26 ` Ping-Ke Shih
0 siblings, 2 replies; 8+ messages in thread
From: Paul Menzel @ 2022-11-08 16:18 UTC (permalink / raw)
To: Ping-Ke Shih; +Cc: linux-wireless, it+linux-wireless
Dear Linux folks,
Am 08.11.22 um 13:49 schrieb Paul Menzel:
> Using Debian sid/unstable with Linux 6.1-rc3 [1] on an Intel Haswell
> Haier laptop with a RTL8188EE, I am unable to connect to a wireless
> network.
>
> $ sudo lspci -k -s 08:00.0
> 08:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188EE Wireless Network Adapter (rev 01)
> Subsystem: AzureWave RTL8188EE Wireless Network Adapter
> Kernel driver in use: rtl8188ee
> Kernel modules: rtl8188ee
>
> ```
> [ 262.822320] wlp8s0: authenticate with 6c:f3:7f:10:ae:12
> [ 262.822341] wlp8s0: 80 MHz not supported, disabling VHT
> [ 262.832384] wlp8s0: send auth to 6c:f3:7f:10:ae:12 (try 1/3)
> [ 262.835124] wlp8s0: authenticated
> [ 262.839046] wlp8s0: associate with 6c:f3:7f:10:ae:12 (try 1/3)
> [ 262.850099] wlp8s0: RX AssocResp from 6c:f3:7f:10:ae:12 (capab=0x421 status=0 aid=1)
> [ 262.850331] wlp8s0: associated
> [ 262.850925] IPv6: ADDRCONF(NETDEV_CHANGE): wlp8s0: link becomes ready
> […]
> [ 307.618423] wlp8s0: deauthenticating from 6c:f3:7f:10:ae:12 by local choice (Reason: 3=DEAUTH_LEAVING)
> ```
>
> wpa_supplicant 2:2.10-9+b2 logs:
>
> ```
> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: SME: Trying to authenticate with 6c:f3:7f:10:ae:12 (SSID='MPI Guest' freq=2437 MHz)
> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: Trying to associate with 6c:f3:7f:10:ae:12 (SSID='MPI Guest' freq=2437 MHz)
> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: Associated with 6c:f3:7f:10:ae:12
> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: CTRL-EVENT-CONNECTED - Connection to 6c:f3:7f:10:ae:12 completed [id=0 id_str=]
> Nov 08 13:29:35 brecht wpa_supplicant[612]: bgscan simple: Failed to enable signal strength monitoring
> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
> Nov 08 13:30:20 brecht wpa_supplicant[612]: wlp8s0: CTRL-EVENT-DISCONNECTED bssid=6c:f3:7f:10:ae:12 reason=3 locally_generated=1
> ```
>
> With more debugging verbosity (`-d`) it shows:
>
> ```
> […]
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: State: ASSOCIATED -> COMPLETED
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Radio work 'sme-connect'@0x556b491b5a80 done in 0.026679 seconds
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: radio_work_free('sme-connect'@0x556b491b5a80): num_active_works --> 0
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: CTRL-EVENT-CONNECTED - Connection to 6c:f3:7f:10:ae:12 completed [id=0
> id_str=]
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Set wlp8s0 operstate 0->1 (UP)
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Signal strength threshold -70 Short bgscan interval 30 Long bgscan interval 86400
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Signal monitor threshold=-70 hysteresis=4
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Failed to enable signal strength monitoring
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Init scan interval: 86400
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan: Initialized module 'simple' with parameters '30:-70:86400'
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Received scan results (19 BSSes)
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Scan results indicate BSS status with 6c:f3:7f:10:ae:12 as associated
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: BSS: Start scan result update 5
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: scan result notification
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Determining shared radio frequencies (max len 1)
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Shared frequencies (len=1): completed iteration
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: freq[0]: 2437, flags=0x1
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Add operating class 81
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Channels - hexdump(len=13): 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Update channel list
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: channels: 81:1,2,3,4,5,6,7,8,9,10,11,12,13
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: cli_channels:
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Cancelling scan request
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: AC mandatory: AC_BE=0 AC_BK=0 AC_VI=0 AC_VO=0
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: U-APSD queues=0x0
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: Valid WMM association, WMM AC is enabled
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: RTM_NEWLINK: ifi_index=3 ifname=wlp8s0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Drv Event 46 (NL80211_CMD_CONNECT) received for wlp8s0
> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Ignore connect event (cmd=46) when using userspace SME
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for wlp8s0
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Delete station 6c:f3:7f:10:ae:12
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Drv Event 39 (NL80211_CMD_DEAUTHENTICATE) received for wlp8s0
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Deauthenticate event
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: Event DEAUTH (11) received
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: Deauthentication notification
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: * reason 3 (DEAUTH_LEAVING) locally_generated=1
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: * address 6c:f3:7f:10:ae:12
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: Deauthentication frame IE(s) - hexdump(len=0): [NULL]
> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: CTRL-EVENT-DISCONNECTED bssid=6c:f3:7f:10:ae:12 reason=3 locally_generated=1
> ```
>
> It’d be really great to get WLAN working on the device.
I tested Debian 11 Live ISO with Linux 5.10 and wpa_supplicant 2.9, and
it has the same problem. I configured iwd, and ran iwmon, which got a
trace [2] (where I unplugged the Ethernet cable during the trace).
Kind regards,
Paul
> [1]: https://packages.debian.org/experimental/linux-image-6.1.0-0-amd64
[2]: https://owww.molgen.mpg.de/~pmenzel/iwmon-rtl8188ee.txt
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: rtlwifi: RTL8188EE: Unable to connect to Wifi network
2022-11-08 16:18 ` Paul Menzel
@ 2022-11-08 22:36 ` Larry Finger
2022-11-15 17:47 ` Paul Menzel
2022-11-09 2:26 ` Ping-Ke Shih
1 sibling, 1 reply; 8+ messages in thread
From: Larry Finger @ 2022-11-08 22:36 UTC (permalink / raw)
To: Paul Menzel, Ping-Ke Shih; +Cc: linux-wireless, it+linux-wireless
On 11/8/22 10:18, Paul Menzel wrote:
> Dear Linux folks,
>
>
> Am 08.11.22 um 13:49 schrieb Paul Menzel:
>
>> Using Debian sid/unstable with Linux 6.1-rc3 [1] on an Intel Haswell Haier
>> laptop with a RTL8188EE, I am unable to connect to a wireless network.
>>
>> $ sudo lspci -k -s 08:00.0
>> 08:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188EE
>> Wireless Network Adapter (rev 01)
>> Subsystem: AzureWave RTL8188EE Wireless Network Adapter
>> Kernel driver in use: rtl8188ee
>> Kernel modules: rtl8188ee
>>
>> ```
>> [ 262.822320] wlp8s0: authenticate with 6c:f3:7f:10:ae:12
>> [ 262.822341] wlp8s0: 80 MHz not supported, disabling VHT
>> [ 262.832384] wlp8s0: send auth to 6c:f3:7f:10:ae:12 (try 1/3)
>> [ 262.835124] wlp8s0: authenticated
>> [ 262.839046] wlp8s0: associate with 6c:f3:7f:10:ae:12 (try 1/3)
>> [ 262.850099] wlp8s0: RX AssocResp from 6c:f3:7f:10:ae:12 (capab=0x421
>> status=0 aid=1)
>> [ 262.850331] wlp8s0: associated
>> [ 262.850925] IPv6: ADDRCONF(NETDEV_CHANGE): wlp8s0: link becomes ready
>> […]
>> [ 307.618423] wlp8s0: deauthenticating from 6c:f3:7f:10:ae:12 by local choice
>> (Reason: 3=DEAUTH_LEAVING)
>> ```
>>
>> wpa_supplicant 2:2.10-9+b2 logs:
>>
>> ```
>> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: SME: Trying to
>> authenticate with 6c:f3:7f:10:ae:12 (SSID='MPI Guest' freq=2437 MHz)
>> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: Trying to associate with
>> 6c:f3:7f:10:ae:12 (SSID='MPI Guest' freq=2437 MHz)
>> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: Associated with
>> 6c:f3:7f:10:ae:12
>> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: CTRL-EVENT-CONNECTED -
>> Connection to 6c:f3:7f:10:ae:12 completed [id=0 id_str=]
>> Nov 08 13:29:35 brecht wpa_supplicant[612]: bgscan simple: Failed to enable
>> signal strength monitoring
>> Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0:
>> CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
>> Nov 08 13:30:20 brecht wpa_supplicant[612]: wlp8s0: CTRL-EVENT-DISCONNECTED
>> bssid=6c:f3:7f:10:ae:12 reason=3 locally_generated=1
>> ```
>>
>> With more debugging verbosity (`-d`) it shows:
>>
>> ```
>> […]
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: State: ASSOCIATED ->
>> COMPLETED
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Radio work
>> 'sme-connect'@0x556b491b5a80 done in 0.026679 seconds
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0:
>> radio_work_free('sme-connect'@0x556b491b5a80): num_active_works --> 0
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: CTRL-EVENT-CONNECTED -
>> Connection to 6c:f3:7f:10:ae:12 completed [id=0 id_str=]
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Set wlp8s0 operstate
>> 0->1 (UP)
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: netlink: Operstate: ifindex=3
>> linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Signal strength
>> threshold -70 Short bgscan interval 30 Long bgscan interval 86400
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Signal monitor
>> threshold=-70 hysteresis=4
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Failed to enable
>> signal strength monitoring
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Init scan
>> interval: 86400
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan: Initialized module
>> 'simple' with parameters '30:-70:86400'
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Received scan results
>> (19 BSSes)
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Scan results indicate
>> BSS status with 6c:f3:7f:10:ae:12 as associated
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: BSS: Start scan result
>> update 5
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: scan result
>> notification
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Determining shared radio
>> frequencies (max len 1)
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Shared frequencies
>> (len=1): completed iteration
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: freq[0]: 2437, flags=0x1
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Add operating class 81
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Channels - hexdump(len=13):
>> 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Update channel list
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: channels:
>> 81:1,2,3,4,5,6,7,8,9,10,11,12,13
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: cli_channels:
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Cancelling scan request
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: AC mandatory: AC_BE=0
>> AC_BK=0 AC_VI=0 AC_VO=0
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: U-APSD queues=0x0
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: Valid WMM association,
>> WMM AC is enabled
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0:
>> CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: RTM_NEWLINK: ifi_index=3
>> ifname=wlp8s0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043
>> ([UP][RUNNING][LOWER_UP])
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Drv Event 46
>> (NL80211_CMD_CONNECT) received for wlp8s0
>> Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Ignore connect event
>> (cmd=46) when using userspace SME
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Drv Event 20
>> (NL80211_CMD_DEL_STATION) received for wlp8s0
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Delete station
>> 6c:f3:7f:10:ae:12
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Drv Event 39
>> (NL80211_CMD_DEAUTHENTICATE) received for wlp8s0
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Deauthenticate event
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: Event DEAUTH (11) received
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: Deauthentication
>> notification
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: * reason 3
>> (DEAUTH_LEAVING) locally_generated=1
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: * address 6c:f3:7f:10:ae:12
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: Deauthentication frame IE(s) -
>> hexdump(len=0): [NULL]
>> Nov 08 13:42:58 brecht wpa_supplicant[3547]: wlp8s0: CTRL-EVENT-DISCONNECTED
>> bssid=6c:f3:7f:10:ae:12 reason=3 locally_generated=1
>> ```
>>
>> It’d be really great to get WLAN working on the device.
>
> I tested Debian 11 Live ISO with Linux 5.10 and wpa_supplicant 2.9, and it has
> the same problem. I configured iwd, and ran iwmon, which got a trace [2] (where
> I unplugged the Ethernet cable during the trace).
I cannot duplicate your problem. When I installed the RTL8188EE chip in my
computer, wifi connected immediately, even before I connected an external antenna.
My configuration is openSUSE Tumbleweed running a 6.1-rc4 kernel. The network is
controlled by NetworkManager v1.40.2 with wpa_supplicant v2.10-4.
Larry
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: rtlwifi: RTL8188EE: Unable to connect to Wifi network
2022-11-08 16:18 ` Paul Menzel
2022-11-08 22:36 ` Larry Finger
@ 2022-11-09 2:26 ` Ping-Ke Shih
1 sibling, 0 replies; 8+ messages in thread
From: Ping-Ke Shih @ 2022-11-09 2:26 UTC (permalink / raw)
To: Paul Menzel
Cc: linux-wireless@vger.kernel.org, it+linux-wireless@molgen.mpg.de
> -----Original Message-----
> From: Paul Menzel <pmenzel@molgen.mpg.de>
> Sent: Wednesday, November 9, 2022 12:18 AM
> To: Ping-Ke Shih <pkshih@realtek.com>
> Cc: linux-wireless@vger.kernel.org; it+linux-wireless@molgen.mpg.de
> Subject: Re: rtlwifi: RTL8188EE: Unable to connect to Wifi network
>
> Dear Linux folks,
>
>
> Am 08.11.22 um 13:49 schrieb Paul Menzel:
>
> > Using Debian sid/unstable with Linux 6.1-rc3 [1] on an Intel Haswell
> > Haier laptop with a RTL8188EE, I am unable to connect to a wireless
> > network.
> >
> > $ sudo lspci -k -s 08:00.0
> > 08:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188EE Wireless Network Adapter (rev
> 01)
> > Subsystem: AzureWave RTL8188EE Wireless Network Adapter
> > Kernel driver in use: rtl8188ee
> > Kernel modules: rtl8188ee
> >
> > ```
> > [ 262.822320] wlp8s0: authenticate with 6c:f3:7f:10:ae:12
> > [ 262.822341] wlp8s0: 80 MHz not supported, disabling VHT
> > [ 262.832384] wlp8s0: send auth to 6c:f3:7f:10:ae:12 (try 1/3)
> > [ 262.835124] wlp8s0: authenticated
> > [ 262.839046] wlp8s0: associate with 6c:f3:7f:10:ae:12 (try 1/3)
> > [ 262.850099] wlp8s0: RX AssocResp from 6c:f3:7f:10:ae:12 (capab=0x421 status=0 aid=1)
> > [ 262.850331] wlp8s0: associated
> > [ 262.850925] IPv6: ADDRCONF(NETDEV_CHANGE): wlp8s0: link becomes ready
> > […]
> > [ 307.618423] wlp8s0: deauthenticating from 6c:f3:7f:10:ae:12 by local choice (Reason: 3=DEAUTH_LEAVING)
> > ```
> >
> > wpa_supplicant 2:2.10-9+b2 logs:
> >
> > ```
> > Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: SME: Trying to authenticate with 6c:f3:7f:10:ae:12
> (SSID='MPI Guest' freq=2437 MHz)
> > Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: Trying to associate with 6c:f3:7f:10:ae:12 (SSID='MPI
> Guest' freq=2437 MHz)
> > Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: Associated with 6c:f3:7f:10:ae:12
> > Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: CTRL-EVENT-CONNECTED - Connection to
> 6c:f3:7f:10:ae:12 completed [id=0 id_str=]
> > Nov 08 13:29:35 brecht wpa_supplicant[612]: bgscan simple: Failed to enable signal strength monitoring
> > Nov 08 13:29:35 brecht wpa_supplicant[612]: wlp8s0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
> > Nov 08 13:30:20 brecht wpa_supplicant[612]: wlp8s0: CTRL-EVENT-DISCONNECTED bssid=6c:f3:7f:10:ae:12
> reason=3 locally_generated=1
> > ```
> >
> > With more debugging verbosity (`-d`) it shows:
> >
> > ```
> > […]
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: State: ASSOCIATED -> COMPLETED
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Radio work 'sme-connect'@0x556b491b5a80 done in
> 0.026679 seconds
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: radio_work_free('sme-connect'@0x556b491b5a80):
> num_active_works --> 0
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: CTRL-EVENT-CONNECTED - Connection to
> 6c:f3:7f:10:ae:12 completed [id=0
> > id_str=]
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Set wlp8s0 operstate 0->1 (UP)
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: netlink: Operstate: ifindex=3 linkmode=-1 (no change),
> operstate=6 (IF_OPER_UP)
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Signal strength threshold -70 Short bgscan
> interval 30 Long bgscan interval 86400
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Signal monitor threshold=-70 hysteresis=4
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Failed to enable signal strength monitoring
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: Init scan interval: 86400
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan: Initialized module 'simple' with parameters
> '30:-70:86400'
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Received scan results (19 BSSes)
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Scan results indicate BSS status with
> 6c:f3:7f:10:ae:12 as associated
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: BSS: Start scan result update 5
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: bgscan simple: scan result notification
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Determining shared radio frequencies (max len 1)
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Shared frequencies (len=1): completed iteration
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: freq[0]: 2437, flags=0x1
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Add operating class 81
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Channels - hexdump(len=13): 01 02 03 04 05 06 07 08
> 09 0a 0b 0c 0d
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: Update channel list
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: channels: 81:1,2,3,4,5,6,7,8,9,10,11,12,13
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: P2P: cli_channels:
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: Cancelling scan request
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: AC mandatory: AC_BE=0 AC_BK=0 AC_VI=0 AC_VO=0
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: U-APSD queues=0x0
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: WMM AC: Valid WMM association, WMM AC is enabled
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: wlp8s0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: RTM_NEWLINK: ifi_index=3 ifname=wlp8s0 operstate=6
> linkmode=1 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Drv Event 46 (NL80211_CMD_CONNECT) received for
> wlp8s0
> > Nov 08 13:42:13 brecht wpa_supplicant[3547]: nl80211: Ignore connect event (cmd=46) when using userspace
> SME
> > Nov 08 13:42:58 brecht wpa_supplicant[3547]: nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received
No beacon loss messages between NL80211_CMD_CONNECT and NL80211_CMD_DEL_STATION, so
8188ee seems to receive packets well.
Please check if you have more than one daemon working at the same time.
A way is to turn off WiFi from GUI, and use 'iw connect' to connect an
AP without security.
Ping-Ke
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: rtlwifi: RTL8188EE: Unable to connect to Wifi network
2022-11-08 22:36 ` Larry Finger
@ 2022-11-15 17:47 ` Paul Menzel
2022-11-15 22:21 ` Larry Finger
0 siblings, 1 reply; 8+ messages in thread
From: Paul Menzel @ 2022-11-15 17:47 UTC (permalink / raw)
To: Larry Finger, Ping-Ke Shih; +Cc: linux-wireless, it+linux-wireless
Dear Larry, dear Ping-Ke,
Thank you very much for your replies.
Am 08.11.22 um 23:36 schrieb Larry Finger:
> On 11/8/22 10:18, Paul Menzel wrote:
[…]
>> Am 08.11.22 um 13:49 schrieb Paul Menzel:
>>
>>> Using Debian sid/unstable with Linux 6.1-rc3 [1] on an Intel Haswell
>>> Haier laptop with a RTL8188EE, I am unable to connect to a wireless
>>> network.
>>>
>>> $ sudo lspci -k -s 08:00.0
>>> 08:00.0 Network controller: Realtek Semiconductor Co., Ltd.
>>> RTL8188EE Wireless Network Adapter (rev 01)
>>> Subsystem: AzureWave RTL8188EE Wireless Network Adapter
>>> Kernel driver in use: rtl8188ee
>>> Kernel modules: rtl8188ee
>>>
>>> ```
>>> [ 262.822320] wlp8s0: authenticate with 6c:f3:7f:10:ae:12
>>> [ 262.822341] wlp8s0: 80 MHz not supported, disabling VHT
>>> [ 262.832384] wlp8s0: send auth to 6c:f3:7f:10:ae:12 (try 1/3)
>>> [ 262.835124] wlp8s0: authenticated
>>> [ 262.839046] wlp8s0: associate with 6c:f3:7f:10:ae:12 (try 1/3)
>>> [ 262.850099] wlp8s0: RX AssocResp from 6c:f3:7f:10:ae:12 (capab=0x421 status=0 aid=1)
>>> [ 262.850331] wlp8s0: associated
>>> [ 262.850925] IPv6: ADDRCONF(NETDEV_CHANGE): wlp8s0: link becomes ready
>>> […]
>>> [ 307.618423] wlp8s0: deauthenticating from 6c:f3:7f:10:ae:12 by local choice (Reason: 3=DEAUTH_LEAVING)
>>> ```
>>>
>>> wpa_supplicant 2:2.10-9+b2 logs:
[…]
>>> With more debugging verbosity (`-d`) it shows:
[…]
>>> It’d be really great to get WLAN working on the device.
>>
>> I tested Debian 11 Live ISO with Linux 5.10 and wpa_supplicant 2.9,
>> and it has the same problem. I configured iwd, and ran iwmon, which
>> got a trace [2] (where I unplugged the Ethernet cable during the trace).
>
> I cannot duplicate your problem. When I installed the RTL8188EE chip in
> my computer, wifi connected immediately, even before I connected an
> external antenna.
>
> My configuration is openSUSE Tumbleweed running a 6.1-rc4 kernel. The
> network is controlled by NetworkManager v1.40.2 with wpa_supplicant
> v2.10-4.
Thank you for checking. Just a quick update, the user reported back,
that Wifi is working fine at here home. So it must be some
incompatibility with our institute Aruba access points/Wifi.
Hopefully I have more time next week to gather more logs.
Kind regards,
Paul
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: rtlwifi: RTL8188EE: Unable to connect to Wifi network
2022-11-15 17:47 ` Paul Menzel
@ 2022-11-15 22:21 ` Larry Finger
2023-09-18 13:46 ` Paul Menzel
0 siblings, 1 reply; 8+ messages in thread
From: Larry Finger @ 2022-11-15 22:21 UTC (permalink / raw)
To: Paul Menzel, Ping-Ke Shih; +Cc: linux-wireless, it+linux-wireless
On 11/15/22 11:47, Paul Menzel wrote:
>
> Thank you for checking. Just a quick update, the user reported back, that Wifi
> is working fine at here home. So it must be some incompatibility with our
> institute Aruba access points/Wifi.
>
> Hopefully I have more time next week to gather more logs.
One thing that would be useful would be the in-the-air packets captured with
WireShark. That way we could see the actual probe and response.
Larry
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: rtlwifi: RTL8188EE: Unable to connect to Wifi network
2022-11-15 22:21 ` Larry Finger
@ 2023-09-18 13:46 ` Paul Menzel
2023-10-03 8:56 ` Ping-Ke Shih
0 siblings, 1 reply; 8+ messages in thread
From: Paul Menzel @ 2023-09-18 13:46 UTC (permalink / raw)
To: Larry Finger, Ping-Ke Shih; +Cc: linux-wireless, it+linux-wireless
[-- Attachment #1: Type: text/plain, Size: 22542 bytes --]
Dear Larry, dear Ping-Ke,
Am 15.11.22 um 23:21 schrieb Larry Finger:
> On 11/15/22 11:47, Paul Menzel wrote:
>>
>> Thank you for checking. Just a quick update, the user reported back,
>> that Wifi is working fine at her home. So it must be some
>> incompatibility with our institute Aruba access points/Wifi.
>>
>> Hopefully I have more time next week to gather more logs.
>
> One thing that would be useful would be the in-the-air packets captured
> with WireShark. That way we could see the actual probe and response.
I am sorry for not getting back to you earlier. The user worked around
the situation at our institute with Aruba access points by using a wired
connection, the laptop luckily still has.
The current stack is *linux-image-6.4.0-2-amd64* 6.4.4-3,
*wpasupplicant* 2:2.10-15, and *network-manager* 1.44.0-1.
Remotely, I installed *tshark* 4.0.8-1, enabled the Wifi
$ sudo nmcli radio wifi on
and started capturing.
$ tshark -i wlp8s0 -w /dev/shm/20230918--linux-6.4.4--tshark.pcapng
Capturing on 'wlp8s0'
** (tshark:106220) 15:33:22.465772 [Main MESSAGE] -- Capture started.
** (tshark:106220) 15:33:22.465887 [Main MESSAGE] -- File:
"/dev/shm/20230918--linux-6.4.4--tshark.pcapng"
63 ^C
tshark:
`nmcli` showed the status below:
wlp8s0: connecting (getting IP configuration) to MPI Guest
"Realtek RTL8188EE"
wifi (rtl8188ee), 54:27:1E:F6:B8:D3, hw, mtu 1500
Please find the capture attached.
Kind regards,
Paul
PS: Output of `journalctl -b -u wpa_supplicant.service -u
NetworkManager.service`:
```
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.2283]
manager: rfkill: Wi-Fi hardware radio set enabled
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.6391]
audit: op="radio-control" arg="wireless-enabled:on" pid=106213 uid=0
result="success"
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.6395]
manager: rfkill: Wi-Fi now enabled by radio killswitch
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.6789]
device (wlp8s0): supplicant interface state: internal-starting ->
disconnected
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.6789]
device (p2p-dev-wlp8s0): state change: unavailable -> unmanaged (reason
'removed', sys-iface-state: 'removed')
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.6799]
Wi-Fi P2P device controlled by interface wlp8s0 created
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.6803]
manager: (p2p-dev-wlp8s0): new 802.11 Wi-Fi P2P device
(/org/freedesktop/NetworkManager/Devices/9)
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.6807]
device (p2p-dev-wlp8s0): state change: unmanaged -> unavailable (reason
'managed', sys-iface-state: 'external')
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.6820]
device (wlp8s0): state change: unavailable -> disconnected (reason
'supplicant-available', sys-iface-state: 'managed')
Sep 18 15:33:21 brecht NetworkManager[842]: <info> [1695044001.6829]
device (p2p-dev-wlp8s0): state change: unavailable -> disconnected
(reason 'none', sys-iface-state: 'managed')
Sep 18 15:33:22 brecht NetworkManager[842]: <info> [1695044002.8271]
policy: auto-activating connection 'MPI Guest'
(c595bdf3-5106-4f32-a302-1ed03d93634a)
Sep 18 15:33:22 brecht NetworkManager[842]: <info> [1695044002.8284]
device (wlp8s0): Activation: starting connection 'MPI Guest'
(c595bdf3-5106-4f32-a302-1ed03d93634a)
Sep 18 15:33:22 brecht NetworkManager[842]: <info> [1695044002.8287]
device (wlp8s0): state change: disconnected -> prepare (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:33:22 brecht NetworkManager[842]: <info> [1695044002.8512]
device (wlp8s0): set-hw-addr: reset MAC address to 54:27:1E:F6:B8:D3
(preserve)
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2511]
device (wlp8s0): state change: prepare -> config (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2515]
device (wlp8s0): Activation: (wifi) connection 'MPI Guest' requires no
security. No secrets needed.
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2515]
Config: added 'ssid' value 'MPI Guest'
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2516]
Config: added 'scan_ssid' value '1'
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2516]
Config: added 'bgscan' value 'simple:30:-65:300'
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2516]
Config: added 'key_mgmt' value 'NONE'
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2521]
device (wlp8s0): supplicant interface state: disconnected ->
interface_disabled
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2521]
device (p2p-dev-wlp8s0): supplicant management interface state:
disconnected -> interface_disabled
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2660]
device (wlp8s0): supplicant interface state: interface_disabled -> inactive
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2660]
device (p2p-dev-wlp8s0): supplicant management interface state:
interface_disabled -> inactive
Sep 18 15:33:23 brecht wpa_supplicant[73197]: wlp8s0: SME: Trying to
authenticate with 6c:f3:7f:10:a4:12 (SSID='MPI Guest' freq=2437 MHz)
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2792]
device (wlp8s0): supplicant interface state: inactive -> authenticating
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2793]
device (p2p-dev-wlp8s0): supplicant management interface state: inactive
-> authenticating
Sep 18 15:33:23 brecht wpa_supplicant[73197]: wlp8s0: Trying to
associate with 6c:f3:7f:10:a4:12 (SSID='MPI Guest' freq=2437 MHz)
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2906]
device (wlp8s0): supplicant interface state: authenticating -> associating
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.2906]
device (p2p-dev-wlp8s0): supplicant management interface state:
authenticating -> associating
Sep 18 15:33:23 brecht wpa_supplicant[73197]: wlp8s0: Associated with
6c:f3:7f:10:a4:12
Sep 18 15:33:23 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-CONNECTED - Connection to 6c:f3:7f:10:a4:12 completed [id=0
id_str=]
Sep 18 15:33:23 brecht wpa_supplicant[73197]: bgscan simple: Failed to
enable signal strength monitoring
Sep 18 15:33:23 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.3092]
device (wlp8s0): supplicant interface state: associating -> completed
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.3093]
device (wlp8s0): Activation: (wifi) Stage 2 of 5 (Device Configure)
successful. Connected to wireless network "MPI Guest"
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.3093]
device (p2p-dev-wlp8s0): supplicant management interface state:
associating -> completed
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.3106]
device (wlp8s0): state change: config -> ip-config (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:33:23 brecht NetworkManager[842]: <info> [1695044003.3125]
dhcp4 (wlp8s0): activation: beginning transaction (timeout in 45 seconds)
Sep 18 15:34:08 brecht NetworkManager[842]: <info> [1695044048.9884]
device (wlp8s0): state change: ip-config -> failed (reason
'ip-config-unavailable', sys-iface-state: 'managed')
Sep 18 15:34:09 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-DISCONNECTED bssid=6c:f3:7f:10:a4:12 reason=3 locally_generated=1
Sep 18 15:34:09 brecht wpa_supplicant[73197]: BSSID 6c:f3:7f:10:a4:12
ignore list count incremented to 2, ignoring for 10 seconds
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.0350]
device (wlp8s0): set-hw-addr: set MAC address to D6:0D:AC:C9:48:A4
(scanning)
Sep 18 15:34:09 brecht NetworkManager[842]: <warn> [1695044049.4456]
device (wlp8s0): Activation: failed for connection 'MPI Guest'
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.4459]
device (wlp8s0): supplicant interface state: completed -> interface_disabled
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.4460]
device (p2p-dev-wlp8s0): supplicant management interface state:
completed -> interface_disabled
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.4477]
device (wlp8s0): state change: failed -> disconnected (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.4730]
dhcp4 (wlp8s0): canceled DHCP transaction
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.4731]
dhcp4 (wlp8s0): activation: beginning transaction (timeout in 45 seconds)
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.4731]
dhcp4 (wlp8s0): state changed no lease
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.4748]
device (wlp8s0): supplicant interface state: interface_disabled -> scanning
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.4749]
device (p2p-dev-wlp8s0): supplicant management interface state:
interface_disabled -> scanning
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.6257]
device (wlp8s0): supplicant interface state: scanning -> disconnected
Sep 18 15:34:09 brecht NetworkManager[842]: <info> [1695044049.6258]
device (p2p-dev-wlp8s0): supplicant management interface state: scanning
-> disconnected
Sep 18 15:34:10 brecht NetworkManager[842]: <info> [1695044050.7163]
device (wlp8s0): supplicant interface state: disconnected -> inactive
Sep 18 15:34:10 brecht NetworkManager[842]: <info> [1695044050.7164]
device (p2p-dev-wlp8s0): supplicant management interface state:
disconnected -> inactive
Sep 18 15:34:10 brecht NetworkManager[842]: <info> [1695044050.7169]
policy: auto-activating connection 'MPI Guest'
(c595bdf3-5106-4f32-a302-1ed03d93634a)
Sep 18 15:34:10 brecht NetworkManager[842]: <info> [1695044050.7183]
device (wlp8s0): Activation: starting connection 'MPI Guest'
(c595bdf3-5106-4f32-a302-1ed03d93634a)
Sep 18 15:34:10 brecht NetworkManager[842]: <info> [1695044050.7185]
device (wlp8s0): state change: disconnected -> prepare (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:34:10 brecht NetworkManager[842]: <info> [1695044050.7424]
device (wlp8s0): set-hw-addr: reset MAC address to 54:27:1E:F6:B8:D3
(preserve)
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1519]
device (wlp8s0): state change: prepare -> config (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1524]
device (wlp8s0): Activation: (wifi) connection 'MPI Guest' requires no
security. No secrets needed.
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1525]
Config: added 'ssid' value 'MPI Guest'
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1525]
Config: added 'scan_ssid' value '1'
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1525]
Config: added 'bgscan' value 'simple:30:-65:300'
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1525]
Config: added 'key_mgmt' value 'NONE'
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1554]
device (wlp8s0): supplicant interface state: inactive -> interface_disabled
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1555]
device (p2p-dev-wlp8s0): supplicant management interface state: inactive
-> interface_disabled
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1594]
device (wlp8s0): supplicant interface state: interface_disabled -> inactive
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1594]
device (p2p-dev-wlp8s0): supplicant management interface state:
interface_disabled -> inactive
Sep 18 15:34:11 brecht wpa_supplicant[73197]: wlp8s0: SME: Trying to
authenticate with 6c:f3:7f:10:a4:12 (SSID='MPI Guest' freq=2437 MHz)
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1740]
device (wlp8s0): supplicant interface state: inactive -> authenticating
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1740]
device (p2p-dev-wlp8s0): supplicant management interface state: inactive
-> authenticating
Sep 18 15:34:11 brecht wpa_supplicant[73197]: wlp8s0: Trying to
associate with 6c:f3:7f:10:a4:12 (SSID='MPI Guest' freq=2437 MHz)
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1820]
device (wlp8s0): supplicant interface state: authenticating -> associating
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.1821]
device (p2p-dev-wlp8s0): supplicant management interface state:
authenticating -> associating
Sep 18 15:34:11 brecht wpa_supplicant[73197]: wlp8s0: Associated with
6c:f3:7f:10:a4:12
Sep 18 15:34:11 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-CONNECTED - Connection to 6c:f3:7f:10:a4:12 completed [id=0
id_str=]
Sep 18 15:34:11 brecht wpa_supplicant[73197]: bgscan simple: Failed to
enable signal strength monitoring
Sep 18 15:34:11 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.2005]
device (wlp8s0): supplicant interface state: associating -> completed
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.2006]
device (wlp8s0): Activation: (wifi) Stage 2 of 5 (Device Configure)
successful. Connected to wireless network "MPI Guest"
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.2006]
device (p2p-dev-wlp8s0): supplicant management interface state:
associating -> completed
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.2009]
device (wlp8s0): state change: config -> ip-config (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:34:11 brecht NetworkManager[842]: <info> [1695044051.2022]
dhcp4 (wlp8s0): activation: beginning transaction (timeout in 45 seconds)
Sep 18 15:34:55 brecht NetworkManager[842]: <info> [1695044095.9885]
device (wlp8s0): state change: ip-config -> failed (reason
'ip-config-unavailable', sys-iface-state: 'managed')
Sep 18 15:34:56 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-DISCONNECTED bssid=6c:f3:7f:10:a4:12 reason=3 locally_generated=1
Sep 18 15:34:56 brecht wpa_supplicant[73197]: BSSID 6c:f3:7f:10:a4:12
ignore list count incremented to 2, ignoring for 10 seconds
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.0232]
device (wlp8s0): set-hw-addr: set MAC address to 06:9E:A3:55:38:AA
(scanning)
Sep 18 15:34:56 brecht NetworkManager[842]: <warn> [1695044096.4239]
device (wlp8s0): Activation: failed for connection 'MPI Guest'
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.4242]
device (wlp8s0): supplicant interface state: completed -> interface_disabled
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.4242]
device (p2p-dev-wlp8s0): supplicant management interface state:
completed -> interface_disabled
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.4253]
device (wlp8s0): state change: failed -> disconnected (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.4571]
dhcp4 (wlp8s0): canceled DHCP transaction
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.4571]
dhcp4 (wlp8s0): activation: beginning transaction (timeout in 45 seconds)
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.4571]
dhcp4 (wlp8s0): state changed no lease
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.4623]
device (wlp8s0): supplicant interface state: interface_disabled -> scanning
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.4623]
device (p2p-dev-wlp8s0): supplicant management interface state:
interface_disabled -> scanning
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.5685]
device (wlp8s0): supplicant interface state: scanning -> disconnected
Sep 18 15:34:56 brecht NetworkManager[842]: <info> [1695044096.5686]
device (p2p-dev-wlp8s0): supplicant management interface state: scanning
-> disconnected
Sep 18 15:34:57 brecht NetworkManager[842]: <info> [1695044097.6519]
device (wlp8s0): supplicant interface state: disconnected -> inactive
Sep 18 15:34:57 brecht NetworkManager[842]: <info> [1695044097.6520]
device (p2p-dev-wlp8s0): supplicant management interface state:
disconnected -> inactive
Sep 18 15:34:57 brecht NetworkManager[842]: <info> [1695044097.6574]
policy: auto-activating connection 'MPI Guest'
(c595bdf3-5106-4f32-a302-1ed03d93634a)
Sep 18 15:34:57 brecht NetworkManager[842]: <info> [1695044097.6590]
device (wlp8s0): Activation: starting connection 'MPI Guest'
(c595bdf3-5106-4f32-a302-1ed03d93634a)
Sep 18 15:34:57 brecht NetworkManager[842]: <info> [1695044097.6594]
device (wlp8s0): state change: disconnected -> prepare (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:34:57 brecht NetworkManager[842]: <info> [1695044097.6782]
device (wlp8s0): set-hw-addr: reset MAC address to 54:27:1E:F6:B8:D3
(preserve)
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0794]
device (wlp8s0): state change: prepare -> config (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0800]
device (wlp8s0): Activation: (wifi) connection 'MPI Guest' requires no
security. No secrets needed.
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0801]
Config: added 'ssid' value 'MPI Guest'
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0801]
Config: added 'scan_ssid' value '1'
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0801]
Config: added 'bgscan' value 'simple:30:-65:300'
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0802]
Config: added 'key_mgmt' value 'NONE'
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0806]
device (wlp8s0): supplicant interface state: inactive -> interface_disabled
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0806]
device (p2p-dev-wlp8s0): supplicant management interface state: inactive
-> interface_disabled
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0939]
device (wlp8s0): supplicant interface state: interface_disabled -> inactive
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.0940]
device (p2p-dev-wlp8s0): supplicant management interface state:
interface_disabled -> inactive
Sep 18 15:34:58 brecht wpa_supplicant[73197]: wlp8s0: SME: Trying to
authenticate with 6c:f3:7f:10:a4:12 (SSID='MPI Guest' freq=2437 MHz)
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.1071]
device (wlp8s0): supplicant interface state: inactive -> authenticating
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.1072]
device (p2p-dev-wlp8s0): supplicant management interface state: inactive
-> authenticating
Sep 18 15:34:58 brecht wpa_supplicant[73197]: wlp8s0: Trying to
associate with 6c:f3:7f:10:a4:12 (SSID='MPI Guest' freq=2437 MHz)
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.1140]
device (wlp8s0): supplicant interface state: authenticating -> associating
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.1141]
device (p2p-dev-wlp8s0): supplicant management interface state:
authenticating -> associating
Sep 18 15:34:58 brecht wpa_supplicant[73197]: wlp8s0: Associated with
6c:f3:7f:10:a4:12
Sep 18 15:34:58 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-CONNECTED - Connection to 6c:f3:7f:10:a4:12 completed [id=0
id_str=]
Sep 18 15:34:58 brecht wpa_supplicant[73197]: bgscan simple: Failed to
enable signal strength monitoring
Sep 18 15:34:58 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.1329]
device (wlp8s0): supplicant interface state: associating -> completed
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.1333]
device (wlp8s0): Activation: (wifi) Stage 2 of 5 (Device Configure)
successful. Connected to wireless network "MPI Guest"
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.1336]
device (p2p-dev-wlp8s0): supplicant management interface state:
associating -> completed
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.1343]
device (wlp8s0): state change: config -> ip-config (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:34:58 brecht NetworkManager[842]: <info> [1695044098.1354]
dhcp4 (wlp8s0): activation: beginning transaction (timeout in 45 seconds)
Sep 18 15:35:42 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-DISCONNECTED bssid=6c:f3:7f:10:a4:12 reason=3 locally_generated=1
Sep 18 15:35:42 brecht wpa_supplicant[73197]: BSSID 6c:f3:7f:10:a4:12
ignore list count incremented to 2, ignoring for 10 seconds
Sep 18 15:35:42 brecht wpa_supplicant[73197]: rfkill: WLAN soft blocked
Sep 18 15:35:42 brecht NetworkManager[842]: <info> [1695044142.0358]
manager: rfkill: Wi-Fi hardware radio set disabled
Sep 18 15:35:42 brecht NetworkManager[842]: <info> [1695044142.0359]
device (wlp8s0): state change: ip-config -> unavailable (reason 'none',
sys-iface-state: 'managed')
Sep 18 15:35:42 brecht NetworkManager[842]: <info> [1695044142.0530]
dhcp4 (wlp8s0): canceled DHCP transaction
Sep 18 15:35:42 brecht NetworkManager[842]: <info> [1695044142.0531]
dhcp4 (wlp8s0): state changed no lease
Sep 18 15:35:42 brecht NetworkManager[842]: <info> [1695044142.0548]
device (wlp8s0): set-hw-addr: set MAC address to B2:A0:91:38:AF:39
(scanning)
Sep 18 15:35:42 brecht NetworkManager[842]: <info> [1695044142.0597]
audit: op="radio-control" arg="wireless-enabled:off" pid=106337 uid=0
result="success"
Sep 18 15:35:42 brecht NetworkManager[842]: <info> [1695044142.0605]
manager: rfkill: Wi-Fi now disabled by radio killswitch
Sep 18 15:35:42 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-DSCP-POLICY clear_all
Sep 18 15:35:42 brecht NetworkManager[842]: <info> [1695044142.0616]
device (p2p-dev-wlp8s0): state change: disconnected -> unavailable
(reason 'supplicant-failed', sys-iface-state: 'managed')
Sep 18 15:35:42 brecht wpa_supplicant[73197]: wlp8s0:
CTRL-EVENT-DSCP-POLICY clear_all
Sep 18 15:35:42 brecht wpa_supplicant[73197]: nl80211: deinit
ifname=wlp8s0 disabled_11b_rates=0
```
[-- Attachment #2: 20230918--linux-6.4.4--tshark.pcapng --]
[-- Type: application/x-pcapng, Size: 13220 bytes --]
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: rtlwifi: RTL8188EE: Unable to connect to Wifi network
2023-09-18 13:46 ` Paul Menzel
@ 2023-10-03 8:56 ` Ping-Ke Shih
0 siblings, 0 replies; 8+ messages in thread
From: Ping-Ke Shih @ 2023-10-03 8:56 UTC (permalink / raw)
To: Paul Menzel, Larry Finger
Cc: linux-wireless@vger.kernel.org, it+linux-wireless@molgen.mpg.de
> -----Original Message-----
> From: Paul Menzel <pmenzel@molgen.mpg.de>
> Sent: Monday, September 18, 2023 9:46 PM
> To: Larry Finger <Larry.Finger@lwfinger.net>; Ping-Ke Shih <pkshih@realtek.com>
> Cc: linux-wireless@vger.kernel.org; it+linux-wireless@molgen.mpg.de
> Subject: Re: rtlwifi: RTL8188EE: Unable to connect to Wifi network
>
> Dear Larry, dear Ping-Ke,
>
>
> Am 15.11.22 um 23:21 schrieb Larry Finger:
> > On 11/15/22 11:47, Paul Menzel wrote:
> >>
> >> Thank you for checking. Just a quick update, the user reported back,
> >> that Wifi is working fine at her home. So it must be some
> >> incompatibility with our institute Aruba access points/Wifi.
> >>
> >> Hopefully I have more time next week to gather more logs.
> >
> > One thing that would be useful would be the in-the-air packets captured
> > with WireShark. That way we could see the actual probe and response.
>
> I am sorry for not getting back to you earlier. The user worked around
> the situation at our institute with Aruba access points by using a wired
> connection, the laptop luckily still has.
>
> The current stack is *linux-image-6.4.0-2-amd64* 6.4.4-3,
> *wpasupplicant* 2:2.10-15, and *network-manager* 1.44.0-1.
>
> Remotely, I installed *tshark* 4.0.8-1, enabled the Wifi
>
> $ sudo nmcli radio wifi on
>
> and started capturing.
>
> $ tshark -i wlp8s0 -w /dev/shm/20230918--linux-6.4.4--tshark.pcapng
> Capturing on 'wlp8s0'
> ** (tshark:106220) 15:33:22.465772 [Main MESSAGE] -- Capture started.
> ** (tshark:106220) 15:33:22.465887 [Main MESSAGE] -- File:
> "/dev/shm/20230918--linux-6.4.4--tshark.pcapng"
> 63 ^C
> tshark:
As Larry mentioned "in-the-air packets" would be helpful.
In your captured packets, only 54:27:1e:f6:b8:d3 as source to send out DHCP and
ICMP v6 packets, but I don't know if it really sends out, or peer (AP) doesn't
reply the packets.
>
> `nmcli` showed the status below:
>
> wlp8s0: connecting (getting IP configuration) to MPI Guest
> "Realtek RTL8188EE"
> wifi (rtl8188ee), 54:27:1E:F6:B8:D3, hw, mtu 1500
As your log, I believe it can connect to "MPI Guest"
" wlp8s0: CTRL-EVENT-CONNECTED - Connection to 6c:f3:7f:10:a4:12 completed"
But, somehow it can't yield IP and then disconnect...
"device (wlp8s0): state change: ip-config -> failed (reason 'ip-config-unavailable', sys-iface-state: 'managed')"
I suggest to set fixed IP address via NM to see if it can work.
Ping-Ke
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2023-10-03 9:19 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2022-11-08 12:49 rtlwifi: RTL8188EE: Unable to connect to Wifi network Paul Menzel
2022-11-08 16:18 ` Paul Menzel
2022-11-08 22:36 ` Larry Finger
2022-11-15 17:47 ` Paul Menzel
2022-11-15 22:21 ` Larry Finger
2023-09-18 13:46 ` Paul Menzel
2023-10-03 8:56 ` Ping-Ke Shih
2022-11-09 2:26 ` Ping-Ke Shih
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).