linux-wireless.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Kalle Valo <kvalo@kernel.org>
To: Sven Eckelmann <sven@narfation.org>
Cc: ath12k@lists.infradead.org,
	 Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>,
	 linux-wireless@vger.kernel.org,
	 Ganesh Babu Jothiram <quic_gjothira@quicinc.com>
Subject: Re: [PATCH v3 12/13] wifi: ath12k: Read board id to support split-PHY QCN9274
Date: Thu, 15 Feb 2024 13:32:41 +0200	[thread overview]
Message-ID: <87bk8inesm.fsf@kernel.org> (raw)
In-Reply-To: <23399810.6Emhk5qWAg@ripper> (Sven Eckelmann's message of "Wed, 14 Feb 2024 15:17:11 +0100")

Sven Eckelmann <sven@narfation.org> writes:

> On Monday, 29 January 2024 07:57:23 CET Raj Kumar Bhagat wrote:
>> diff --git a/drivers/net/wireless/ath/ath12k/fw.c
>> b/drivers/net/wireless/ath/ath12k/fw.c
>> index fbcf40c97792..5be4b2d4a19d 100644
>> --- a/drivers/net/wireless/ath/ath12k/fw.c
>> +++ b/drivers/net/wireless/ath/ath12k/fw.c
>> @@ -119,6 +119,13 @@ static int
>> ath12k_fw_request_firmware_api_n(struct ath12k_base *ab,
> [...]
>> +		case ATH12K_FW_IE_AMSS_DUALMAC_IMAGE:
>> +			ath12k_dbg(ab, ATH12K_DBG_BOOT,
>> +				   "found dualmac fw image ie (%zd B)\n",
>> +				   ie_len);
>> +			ab->fw.amss_dualmac_data = data;
>> +			ab->fw.amss_dualmac_len = ie_len;
>> +			break;
>>  		default:
>>  			ath12k_warn(ab, "Unknown FW IE: %u\n", ie_id);
>>  			break;
>
>> @@ -371,16 +375,43 @@ int ath12k_mhi_register(struct ath12k_pci *ab_pci)
> [...]
>> +	if (dualmac) {
>> +		if (ab->fw.amss_dualmac_data && ab->fw.amss_dualmac_len > 0) {
>> +			/* use MHI firmware file from firmware-N.bin */
>> +			mhi_ctrl->fw_data = ab->fw.amss_dualmac_data;
>> +			mhi_ctrl->fw_sz = ab->fw.amss_dualmac_len;
>> +		} else {
>> + ath12k_warn(ab, "dualmac firmware IE not present in
>> firmware-N.bin\n");
>> +			ret = -ENOENT;
>> +			goto free_controller;
>> +		}
>
> I saw this now already multiple times that the source code was referencing the 
> firmware-N.bin (like we had with ath10k). But they aren't published anywhere. 
> I can't find a single one at:
>
> *
> https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/ath11k
> *
> https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/ath12k
> * https://github.com/kvalo/ath11k-firmware
> * https://github.com/quic/upstream-wifi-fw
>
> So I find it odd that the new code now seems to depend on it without actually 
> providing these files anywhere.

For example, firmware-2.bin will be used for qrtr id to support multiple
devices on the same host.

> Might be good to have these soon in linux-firmware.git.

Yeah, we will but just slowly. We are currently moving
ath1?k-firmware.git repos to a new location, firmware-N.bin files should
start emerging after that.

-- 
https://patchwork.kernel.org/project/linux-wireless/list/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches

  reply	other threads:[~2024-02-15 11:32 UTC|newest]

Thread overview: 36+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-01-29  6:57 [PATCH v3 00/13] wifi: ath12k: QCN9274 dualmac bring up Raj Kumar Bhagat
2024-01-29  6:57 ` [PATCH v3 01/13] wifi: ath12k: indicate NON MBSSID vdev by default during vdev start Raj Kumar Bhagat
2024-01-31 21:04   ` Jeff Johnson
2024-02-02 12:33   ` Kalle Valo
2024-01-29  6:57 ` [PATCH v3 02/13] wifi: ath12k: fetch correct pdev id from WMI_SERVICE_READY_EXT_EVENTID Raj Kumar Bhagat
2024-01-31 21:05   ` Jeff Johnson
2024-01-29  6:57 ` [PATCH v3 03/13] wifi: ath12k: add support for peer meta data version Raj Kumar Bhagat
2024-01-31 21:05   ` Jeff Johnson
2024-01-29  6:57 ` [PATCH v3 04/13] wifi: ath12k: fix fetching MCBC flag for QCN9274 Raj Kumar Bhagat
2024-01-31 21:06   ` Jeff Johnson
2024-01-29  6:57 ` [PATCH v3 05/13] wifi: ath12k: Add logic to write QRTR node id to scratch Raj Kumar Bhagat
2024-01-31 21:06   ` Jeff Johnson
2024-02-02 12:20     ` Kalle Valo
2024-02-02 14:32       ` Raj Kumar Bhagat
2024-01-29  6:57 ` [PATCH v3 06/13] wifi: ath12k: fix firmware assert during insmod in memory segment mode Raj Kumar Bhagat
2024-01-31 21:06   ` Jeff Johnson
2024-01-29  6:57 ` [PATCH v3 07/13] wifi: ath12k: split hal_ops to support RX TLVs word mask compaction Raj Kumar Bhagat
2024-01-31 21:07   ` Jeff Johnson
2024-01-29  6:57 ` [PATCH v3 08/13] wifi: ath12k: remove hal_desc_sz from hw params Raj Kumar Bhagat
2024-01-31 21:07   ` Jeff Johnson
2024-01-29  6:57 ` [PATCH v3 09/13] wifi: ath12k: subscribe required word mask from rx tlv Raj Kumar Bhagat
2024-01-31 21:07   ` Jeff Johnson
2024-02-02 12:27   ` Kalle Valo
2024-02-02 14:28     ` Raj Kumar Bhagat
2024-01-29  6:57 ` [PATCH v3 10/13] wifi: ath12k: add MAC id support in WBM error path Raj Kumar Bhagat
2024-01-31 21:08   ` Jeff Johnson
2024-01-29  6:57 ` [PATCH v3 11/13] wifi: ath12k: fix PCI read and write Raj Kumar Bhagat
2024-01-31 21:08   ` Jeff Johnson
2024-01-29  6:57 ` [PATCH v3 12/13] wifi: ath12k: Read board id to support split-PHY QCN9274 Raj Kumar Bhagat
2024-01-31 21:09   ` Jeff Johnson
2024-02-14 14:17   ` Sven Eckelmann
2024-02-15 11:32     ` Kalle Valo [this message]
2024-01-29  6:57 ` [PATCH v3 13/13] wifi: ath12k: disable QMI PHY capability learn in split-phy QCN9274 Raj Kumar Bhagat
2024-01-30  1:52   ` Jeff Johnson
2024-01-30  3:04     ` Raj Kumar Bhagat
2024-01-31 21:08   ` Jeff Johnson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=87bk8inesm.fsf@kernel.org \
    --to=kvalo@kernel.org \
    --cc=ath12k@lists.infradead.org \
    --cc=linux-wireless@vger.kernel.org \
    --cc=quic_gjothira@quicinc.com \
    --cc=quic_rajkbhag@quicinc.com \
    --cc=sven@narfation.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).