Re: [OpenWrt-Devel] ATH10K VLAN firmware issue

[yu-chieh kung <jay0607@gmail.com>]

I met the same problem before,
if i modify the 1q header to other value (0xaa00) before go into firmware.
I can capture the packet in the air
I think the vlan packet is dropped in firmware.

2016-11-04 22:41 GMT+08:00 Bruno Antunes <baantunes@gmail.com>:
> On 4 November 2016 at 14:18, Mauro Mozzarelli <openwrt@ezplanet.net> wrot=
e:
>> Since the capability is implemented in software you might be testing the
>> limit of your router's CPU i/o speed.
>
> By loading the module in rawmode?
>
> The AP is an APU and Sta is an APU2.
>
>>
>>
>>
>> On 04/11/16 14:13, Bruno Antunes wrote:
>>>
>>> Hi all,
>>>
>>> Old thread but I think the issue is still present.
>>>
>>> I'm running a setup with VLANs with WDS and ath10k cards.
>>>
>>> To make it work both cards must be loaded in rawmode, AP
>>> and Sta, and with no security.
>>>
>>> I'm using a OpenWrt trunk r49941 and the most recent firmware,
>>> 10.2.4.70.58, from Kalle ath10k firmware tree.
>>>
>>> Although it works the throughput is very bad.
>>> Are there any alternatives to improve the throughput.
>>>
>>> Best Regards,
>>> Bruno
>>>
>>> On 9 December 2015 at 17:24, voncken <cedric.voncken@acksys.fr> wrote:
>>>>
>>>>
>>>>> -----Message d'origine-----
>>>>> De : Ben Greear [mailto:greearb@candelatech.com]
>>>>> Envoy=C3=A9 : mercredi 9 d=C3=A9cembre 2015 16:34
>>>>> =C3=80 : Cedric VONCKEN; ath10k@lists.infradead.org; linux-wireless
>>>>> Objet : Re: ATH10K VLAN firmware issue
>>>>>
>>>>> This only happens when you use STA  + WDS, or is .1q broken for you i=
n
>>>>> other cases as well?
>>>>
>>>> No, this issue occurs in all modes (STA, STA + WDS, AP).
>>>>
>>>> Thanks
>>>>
>>>> Cedric.
>>>>
>>>>> Thanks,
>>>>> Ben
>>>>>
>>>>> On 12/08/2015 06:29 AM, Cedric VONCKEN wrote:
>>>>>>
>>>>>>      I'm testing to transmit frame with 802.1q tag (VLAN).
>>>>>>
>>>>>>      My client is set in STA + WDS and the netdev is bridged with et=
h0.
>>>>>>      I have a computer with vlan configuration set connected to the =
STA
>>>>>> eth0.
>>>>>>
>>>>>>      If I try to transmit frames with 802.1q tag, the frames are not
>>>>
>>>> sent.
>>>>>>
>>>>>>      I checked with wireless sniffer, and I don't see the frame with
>>>>>> VLAN
>>>>>> tag (the frames without VLAN tag are sent).
>>>>>>
>>>>>>      I tested with firmware 10.2.4.70.14-2 from kale github,
>>>>>> 10.1.467-ct-com-full-015 from candelatech and 10.2.4.70-2 from
>>>>>> openwrt, and in all cases I have the same issue.
>>>>>>
>>>>>>      Thanks for your help.
>>>>>>
>>>>>>
>>>>>> --
>>>>>> To unsubscribe from this list: send the line "unsubscribe
>>>>>> linux-wireless" in the body of a message to majordomo@vger.kernel.or=
g
>>>>>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>>>>>>
>>>>> --
>>>>> Ben Greear <greearb@candelatech.com>
>>>>> Candela Technologies Inc  http://www.candelatech.com
>>>>
>>>> --
>>>> To unsubscribe from this list: send the line "unsubscribe linux-wirele=
ss"
>>>> in
>>>> the body of a message to majordomo@vger.kernel.org
>>>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>>>
>>> _______________________________________________
>>> openwrt-devel mailing list
>>> openwrt-devel@lists.openwrt.org
>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel@lists.openwrt.org
>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
> _______________________________________________
> ath10k mailing list
> ath10k@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k