From: feldmaus <feldmann_markus@gmx.de>
To: linux-wireless@vger.kernel.org
Subject: Re: Do not get BCM4303 to work
Date: Sun, 04 Jan 2009 12:34:51 +0100 [thread overview]
Message-ID: <gjq6q1$gvc$1@ger.gmane.org> (raw)
In-Reply-To: <495FB6DD.1060807@lwfinger.net>
Larry Finger schrieb:
> Your log does not indicate that you pressed the button to turn the
> wifi on. All we see is that the hardware switch was off.
Yes you are right.
Here is the log during Boot up:
[ 21.389448] b43legacy-phy0: Broadcom 4301 WLAN found
[ 21.451790] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
[ 21.451814] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version
0x2050, Revision 2
[ 21.488040] b43legacy-phy0 debug: Radio initialized
[ 41.176020] input: b43legacy-phy0 as /class/input/input9
[ 41.276065] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[ 41.340931] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[ 41.415190] b43legacy ssb0:0: firmware: requesting
b43legacy/b0g0initvals2.fw
[ 41.624053] b43legacy-phy0: Loading firmware version 0x127, patch
level 14 (2005-04-18 02:36:27)
[ 41.736308] b43legacy-phy0 debug: Chip initialized
[ 41.736617] b43legacy-phy0 debug: 30-bit DMA initialized
[ 41.736769] Registered led device: b43legacy-phy0:tx
[ 41.744956] Registered led device: b43legacy-phy0:rx
[ 41.753043] Registered led device: b43legacy-phy0:radio
[ 41.760983] b43legacy-phy0 debug: Wireless interface started
[ 41.760990] b43legacy-phy0 debug: Adding Interface type 2
[ 42.221213] b43legacy-phy0: Radio hardware status changed to DISABLED
[ 42.230568] b43legacy-phy0 debug: Radio initialized
[ 42.512043] b43legacy-phy0: Radio turned on by software
[ 42.520110] b43legacy-phy0: The hardware RF-kill button still turns
the radio physically off. Press the button to turn it on.
Then i deactivated the wlan with my networkmanager:
[ 626.730050] b43legacy-phy0 debug: Removing Interface type 2
[ 626.738361] b43legacy-phy0 debug: Wireless interface stopped
[ 626.738524] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots: 1/64
[ 626.738579] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots: 0/64
[ 626.738643] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:
0/128
[ 626.744048] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:
0/128
[ 626.752047] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:
0/128
[ 626.762293] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:
0/128
[ 626.768035] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:
2/128
[ 626.776035] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:
0/128
[ 626.784038] b43legacy-phy0 debug: Radio initialized
[ 626.784049] b43legacy-phy0 debug: Radio initialized
Then i activated my wlan with my networkmanager:
[ 651.401677] input: b43legacy-phy0 as /class/input/input10
[ 651.572038] b43legacy-phy0: Loading firmware version 0x127, patch
level 14 (2005-04-18 02:36:27)
[ 651.680310] b43legacy-phy0 debug: Chip initialized
[ 651.680628] b43legacy-phy0 debug: 30-bit DMA initialized
[ 651.680788] Registered led device: b43legacy-phy0:tx
[ 651.680827] Registered led device: b43legacy-phy0:rx
[ 651.680866] Registered led device: b43legacy-phy0:radio
[ 651.680896] b43legacy-phy0 debug: Wireless interface started
[ 651.680903] b43legacy-phy0 debug: Adding Interface type 2
[ 652.420046] b43legacy-phy0: Radio hardware status changed to DISABLED
Regards Markus
prev parent reply other threads:[~2009-01-04 11:33 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-09-08 6:15 Do not get BCM4303 to work feldmaus
2008-09-08 7:34 ` maximilian attems
2008-09-08 19:05 ` Larry Finger
2008-09-12 23:02 ` feldmaus
2008-09-13 0:30 ` Larry Finger
2008-09-26 16:32 ` feldmaus
2008-09-26 17:27 ` Larry Finger
2008-09-26 21:07 ` feldmaus
2008-09-26 23:40 ` Larry Finger
2009-01-03 18:37 ` feldmaus
2009-01-03 18:49 ` feldmaus
2009-01-03 19:00 ` feldmaus
2009-01-03 19:05 ` Larry Finger
2009-01-03 19:39 ` feldmaus
2009-01-04 11:34 ` feldmaus [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='gjq6q1$gvc$1@ger.gmane.org' \
--to=feldmann_markus@gmx.de \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).