Linux wireless drivers development
 help / color / mirror / Atom feed
* Possible WEP encryption error with wpa_supplicant -Dnl80211
From: Holger Schurig @ 2009-09-08  8:16 UTC (permalink / raw)
  To: linux-wireless

Here are some details on my ping problem: I seem to be associated
successfully to an Cisco 1231 AP, but no pings are going through
if I use nl80211.

----------------------------------- test.conf
ctrl_interface=/var/run/wpa_supplicant
network={
        ssid="TEST"
        key_mgmt=NONE
        wep_key0="99999"
}
------------------------------------- test.sh
#!/bin/sh
ifconfig eth1 10.2.1.2 netmask 255.255.255.0 up
./wpa_supplicant \
        -D nl80211 \
        -i eth1 \
        -c test.conf \
        -P /var/run/wpa_supplicant.eth1.pid \
        -C /var/run/wpa_supplicant
---------------------------------------------

# ./TEST.sh
CTRL-EVENT-SCAN-RESULTS
Trying to authenticate with 00:13:19:80:da:30 (SSID='TEST' freq=2412 MHz)
Trying to associate with 00:13:19:80:da:30 (SSID='TEST' freq=2412 MHz)
Associated with 00:13:19:80:da:30
CTRL-EVENT-CONNECTED - Connection to 00:1b:53:11:dc:40 completed (auth) [id=0 id_str=]

$ ping -c 5 10.2.1.1
PING 10.2.1.1 (10.2.1.1) 56(84) bytes of data.
>From 10.2.1.2 icmp_seq=1 Destination Host Unreachable
>From 10.2.1.2 icmp_seq=2 Destination Host Unreachable
>From 10.2.1.2 icmp_seq=3 Destination Host Unreachable
>From 10.2.1.2 icmp_seq=4 Destination Host Unreachable
>From 10.2.1.2 icmp_seq=5 Destination Host Unreachable

--- 10.2.1.1 ping statistics ---
5 packets transmitted, 0 received, +5 errors, 100% packet loss, time 4023ms, pipe 3



While this was happening, I used another wireless card monitor
the channel. I then saw ARP packets, but AFAIK they haven't been
encrypted:

Frame 319 (85 bytes on wire, 85 bytes captured)
    Arrival Time: Sep  8, 2009 09:07:34.529847000
    [Time delta from previous packet: 0.012281000 seconds]
    [Time since reference or first frame: 5.988251000 seconds]
    Frame Number: 319
    Packet Length: 85 bytes
    Capture Length: 85 bytes
    [Frame is marked: False]
    [Protocols in frame: radiotap:wlan:llc:arp]
Radiotap Header v0, Length 25
    Header revision: 0
    Header pad: 0
    Header length: 25
    Present flags: 0x0000086f
        .... .... .... .... .... .... .... ...1 = TSFT: True
        .... .... .... .... .... .... .... ..1. = Flags: True
        .... .... .... .... .... .... .... .1.. = Rate: True
        .... .... .... .... .... .... .... 1... = Channel: True
        .... .... .... .... .... .... ...0 .... = FHSS: False
        .... .... .... .... .... .... ..1. .... = DBM Antenna Signal: True
        .... .... .... .... .... .... .1.. .... = DBM Antenna Noise: True
        .... .... .... .... .... .... 0... .... = Lock Quality: False
        .... .... .... .... .... ...0 .... .... = TX Attenuation: False
        .... .... .... .... .... ..0. .... .... = DB TX Attenuation: False
        .... .... .... .... .... .0.. .... .... = DBM TX Attenuation: False
        .... .... .... .... .... 1... .... .... = Antenna: True
        .... .... .... .... ...0 .... .... .... = DB Antenna Signal: False
        .... .... .... .... ..0. .... .... .... = DB Antenna Noise: False
        .... .... .... .... .0.. .... .... .... = FCS in header: False
        0... .... .... .... .... .... .... .... = Ext: False
    MAC timestamp: 0
    Flags: 0x00
        .... ...0 = CFP: False
        .... ..0. = Preamble: Long
        .... .0.. = WEP: False
        .... 0... = Fragmentation: False
        ...0 .... = FCS at end: False
        ..0. .... = Data Pad: False
    Data Rate: 11.0 Mb/s
    Channel: 2412 (chan 1)
    Channel type: 802.11b (0x00a0)
    SSI Signal: -17 dBm
    SSI Noise: 0 dBm
    Antenna: 2
IEEE 802.11
    Type/Subtype: Data (32)
    Frame Control: 0x0108 (Normal)
        Version: 0
        Type: Data frame (2)
        Subtype: 0
        Flags: 0x1
            DS status: Frame from STA to DS via an AP (To DS: 1 From DS: 0) (0x01)
            .... .0.. = More Fragments: This is the last fragment
            .... 0... = Retry: Frame is not being retransmitted
            ...0 .... = PWR MGT: STA will stay up
            ..0. .... = More Data: No data buffered
            .0.. .... = Protected flag: Data is not protected
            0... .... = Order flag: Not strictly ordered
    Duration: 213
    BSS Id: 00:1b:53:11:dc:40 (00:1b:53:11:dc:40)
    Source address: Proxim_a0:6d:40 (00:20:a6:a0:6d:40)
    Destination address: Broadcast (ff:ff:ff:ff:ff:ff)
    Fragment number: 0
    Sequence number: 120
Logical-Link Control
    DSAP: SNAP (0xaa)
    IG Bit: Individual
    SSAP: SNAP (0xaa)
    CR Bit: Command
    Control field: U, func=UI (0x03)
        000. 00.. = Command: Unnumbered Information (0x00)
        .... ..11 = Frame type: Unnumbered frame (0x03)
    Organization Code: Encapsulated Ethernet (0x000000)
    Type: ARP (0x0806)
Address Resolution Protocol (request)
    Hardware type: Ethernet (0x0001)
    Protocol type: IP (0x0800)
    Hardware size: 6
    Protocol size: 4
    Opcode: request (0x0001)
    Sender MAC address: Proxim_a0:6d:40 (00:20:a6:a0:6d:40)
    Sender IP address: 10.2.1.2 (10.2.1.2)
    Target MAC address: 00:00:00_00:00:00 (00:00:00:00:00:00)
    Target IP address: 10.2.1.1 (10.2.1.1)






After removing all kernel modules and reloading them again (ath5k,
mac80211, ath, cfg80211) and replacing the "-D nl80211" with "-D wext",
the ping works.

# ./TEST.sh
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCSIWSCAN]: Device or resource busy
Failed to initiate AP scan.
CTRL-EVENT-SCAN-RESULTS
Trying to associate with 00:1b:53:11:dc:40 (SSID='TEST' freq=2412 MHz)
CTRL-EVENT-SCAN-RESULTS
Trying to associate with 00:13:19:80:da:30 (SSID='TEST' freq=2412 MHz)
Associated with 00:13:19:80:da:30
CTRL-EVENT-CONNECTED - Connection to 00:13:19:80:da:30 completed (auth) [id=0 id_str=]

-- 
http://www.holgerschurig.de

^ permalink raw reply

* Re: Possible WEP encryption error with wpa_supplicant -Dnl80211
From: Holger Schurig @ 2009-09-08  8:27 UTC (permalink / raw)
  To: linux-wireless
In-Reply-To: <200909081016.37204.hs4233@mail.mn-solutions.de>

> IEEE 802.11
>     Type/Subtype: Data (32)
>     Frame Control: 0x0108 (Normal)
>         Version: 0
>         Type: Data frame (2)
>         Subtype: 0
>         Flags: 0x1
>             DS status: Frame from STA to DS via an AP (To DS: 1 From DS: 0) (0x01)
>             .... .0.. = More Fragments: This is the last fragment
>             .... 0... = Retry: Frame is not being retransmitted
>             ...0 .... = PWR MGT: STA will stay up
>             ..0. .... = More Data: No data buffered
>             .0.. .... = Protected flag: Data is not protected
>             0... .... = Order flag: Not strictly ordered
>     Duration: 213
>     BSS Id: 00:1b:53:11:dc:40 (00:1b:53:11:dc:40)
>     Source address: Proxim_a0:6d:40 (00:20:a6:a0:6d:40)
>     Destination address: Broadcast (ff:ff:ff:ff:ff:ff)
>     Fragment number: 0
>     Sequence number: 120

When I run wpa_supplicant with -D wext, I see this additional
field while monitoring:

    WEP parameters
        Initialization Vector: 0x222e52
        Key Index: 0
        WEP ICV: 0x9dc1791b (not verified)

-- 
http://www.holgerschurig.de

^ permalink raw reply

* Re: Possible WEP encryption error with wpa_supplicant -Dnl80211
From: Johannes Berg @ 2009-09-08  9:18 UTC (permalink / raw)
  To: Holger Schurig; +Cc: linux-wireless
In-Reply-To: <200909081016.37204.hs4233@mail.mn-solutions.de>

[-- Attachment #1: Type: text/plain, Size: 358 bytes --]

On Tue, 2009-09-08 at 10:16 +0200, Holger Schurig wrote:
> Here are some details on my ping problem: I seem to be associated
> successfully to an Cisco 1231 AP, but no pings are going through
> if I use nl80211.

Yeah, WEP with nl80211 is known broken. I have a patch, but Jouni didn't
like it and I haven't gotten around to fixing it up.

johannes

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 801 bytes --]

^ permalink raw reply

* Re: iwlagn: order 2 page allocation failures
From: Mel Gorman @ 2009-09-08 10:54 UTC (permalink / raw)
  To: Pekka Enberg
  Cc: Frans Pop, linux-kernel, linux-wireless, ipw3945-devel,
	Andrew Morton, cl
In-Reply-To: <1252226116.11274.10.camel@penberg-laptop>

On Sun, Sep 06, 2009 at 11:35:16AM +0300, Pekka Enberg wrote:
> On Sun, 2009-09-06 at 10:28 +0200, Frans Pop wrote:
> > On Sunday 06 September 2009, Pekka Enberg wrote:
> > > On Sun, Sep 6, 2009 at 10:40 AM, Frans Pop<elendil@planet.nl> wrote:
> > > > Got a couple of page allocation failures today while viewing fairly
> > > > large images. System was struggling for a bit to reorganize memory
> > > > and swap, but nothing really serious. Everything recovered fairly
> > > > quickly.
> > > >
> > > > Anything to look into?
> > > >
> > > > System: HP 2510p; 2.6.31-rc7-56-g7c0a57d; Debian stable, KDE desktop
> > > >
> > > > 10:00.0 Network controller [0280]: Intel Corporation PRO/Wireless
> > > > 4965 AG or AGN [Kedron] Network Connection [8086:4229] (rev 61)
> > >
> > > Can you post your .config, please?
> > 
> > Attached. Thanks.
> 
> OK, so SLUB_DEBUG_ON is disabled so it's probably not a SLUB problem.
> Mel, there's quite a few page allocation failure reports recently which
> makes me wonder if we broke something with the page allocator
> optimization patches? Do you think the anti-fragmentation fixlet you did
> for nommu would help here?
> 

No, because that change only affected the case where the system had very
little memory. The last time that there was a sudden major increase in
allocation failures, it was actually was page reclaim was broken -
specifically kswapd was no longer doing the job that was expected of it.
The symptoms where applications stalling because they were entering
direct reclaim. I haven't looked very closely at this bug report yet
(catching up from being offline the last 5 days).

Have there been any reclaim changes that might account for something like this?

My feeling is also that a number of these page allocation failures have
been related to wireless drivers. Is that accurate? If so, have there
been changes made to the wireless stack in this cycle that would have
increased the order of pages allocated?

-- 
Mel Gorman
Part-time Phd Student                          Linux Technology Center
University of Limerick                         IBM Dublin Software Lab

^ permalink raw reply

* Re: ipw2200: firmware DMA loading rework
From: Mel Gorman @ 2009-09-08 11:00 UTC (permalink / raw)
  To: Theodore Tso, Luis R. Rodriguez, Bartlomiej Zolnierkiewicz,
	Aneesh Kumar K.V, Zhu Yi, Andrew Morton, Johannes Weiner,
	Pekka Enberg, Rafael J. Wysocki, Linux Kernel Mailing List,
	Kernel Testers List, Mel Gorman, netdev@vger.kernel.org,
	linux-mm@kvack.org, James Ketrenos, Chatre, Reinette,
	linux-wireless@vger.kernel.org,
	ipw2100-devel@lists.sourceforge.net
In-Reply-To: <20090905142837.GI16217@mit.edu>

On Sat, Sep 05, 2009 at 10:28:37AM -0400, Theodore Tso wrote:
> On Thu, Sep 03, 2009 at 01:49:14PM +0100, Mel Gorman wrote:
> > > 
> > > This looks very similar to the kmemleak ext4 reports upon a mount. If
> > > it is the same issue, which from the trace it seems it is, then this
> > > is due to an extra kmalloc() allocation and this apparently will not
> > > get fixed on 2.6.31 due to the closeness of the merge window and the
> > > non-criticalness this issue has been deemed.
> 
> No, it's a different problem.
> 
> > I suspect the more pressing concern is why is this kmalloc() resulting in
> > an order-5 allocation request? What size is the buffer being requested?
> > Was that expected?  What is the contents of /proc/slabinfo in case a buffer
> > that should have required order-1 or order-2 is using a higher order for
> > some reason.
> 
> It's allocating 68,000 bytes for the mb_history structure, which is
> used for debugging purposes.  That's why it's optional and we continue
> if it's not allocated.  We should fix it to use vmalloc()

You could call with kmalloc(FLAGS|GFP_NOWARN) with a fallback to
vmalloc() and a disable if vmalloc() fails as well.  Maybe check out what
kernel/profile.c#profile_init() to allocate a large buffer and do something
similar?

> and I'm
> inclined to turn it off by default since it's not worth the overhead,
> and most ext4 users won't find it useful or interesting.
> 

I can't comment as I don't know what sort of debugging it's useful for.

-- 
Mel Gorman
Part-time Phd Student                          Linux Technology Center
University of Limerick                         IBM Dublin Software Lab

^ permalink raw reply

* Re: iwlagn: order 2 page allocation failures
From: Pekka Enberg @ 2009-09-08 11:11 UTC (permalink / raw)
  To: Mel Gorman
  Cc: Frans Pop, linux-kernel, linux-wireless, ipw3945-devel,
	Andrew Morton, cl
In-Reply-To: <20090908105415.GD28127@csn.ul.ie>

On Tue, Sep 8, 2009 at 1:54 PM, Mel Gorman<mel@csn.ul.ie> wrote:
> My feeling is also that a number of these page allocation failures have
> been related to wireless drivers. Is that accurate? If so, have there
> been changes made to the wireless stack in this cycle that would have
> increased the order of pages allocated?

That's my general feeling as well. We have linux-wireless CC'd so
maybe this rings a bell for them.

^ permalink raw reply

* Re: Stop using tasklets for bottom halves
From: Steven Rostedt @ 2009-09-08 13:18 UTC (permalink / raw)
  To: Luis R. Rodriguez
  Cc: Stephen Hemminger, Ingo Molnar, Michael Buesch, John W. Linville,
	linux-wireless, linux-kernel, netdev, Matt Smith, Kevin Hayes,
	Bob Copeland, Jouni Malinen, Ivan Seskar, ic.felix
In-Reply-To: <43e72e890909072116v33ecafc4ma7f5a68825f14e9@mail.gmail.com>

On Mon, 2009-09-07 at 21:16 -0700, Luis R. Rodriguez wrote:
> On Mon, Sep 7, 2009 at 7:17 PM, Steven Rostedt<rostedt@goodmis.org> wrote:

> >>
> >> Process context is too slow.
> >
> > Well, I'm hoping to prove the opposite. I'm working on some stuff that I
> > plan to present at Linux Plumbers. I've been too distracted by other
> > things, but hopefully I'll have some good numbers to present by then.
> 
> What day in specific was this planned for at Plumbers?

Wednesday, during the networking session.

  http://linuxplumbersconf.org/ocw/proposals/53

-- Steve



^ permalink raw reply

* b43 dma error
From: Dave Young @ 2009-09-08 13:47 UTC (permalink / raw)
  To: mb; +Cc: linville, netrolller.3d, linux-wireless, bcm43xx-dev

I tested wireless-testing b43 driver, but got "Fatal DMA error"
then the controller keep restarting...

Please tell what I can provide or test, Thanks.

The dmesg:

[  206.995465] b43-phy0 debug: Chip initialized
[  206.995620] b43-phy0 debug: 64-bit DMA initialized
[  207.004517] Registered led device: b43-phy0::tx
[  207.004995] Registered led device: b43-phy0::rx
[  207.005492] Registered led device: b43-phy0::radio
[  207.005752] b43-phy0 debug: Wireless interface started
[  207.005847] b43-phy0 debug: Wireless interface stopped
[  207.007322] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  207.007545] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  207.009291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  207.011296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  207.013293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  207.015298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  207.161463] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  207.163853] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  208.544478] b43-phy0 debug: Chip initialized
[  208.544630] b43-phy0 debug: 64-bit DMA initialized
[  208.553525] Registered led device: b43-phy0::tx
[  208.554006] Registered led device: b43-phy0::rx
[  208.554478] Registered led device: b43-phy0::radio
[  208.554970] b43-phy0 debug: Wireless interface started
[  208.554974] __ratelimit: 6 callbacks suppressed
[  208.554976] b43-phy0: Controller restarted
[  208.555043] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  208.555049] b43-phy0: Controller RESET (DMA error) ...
[  208.555086] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  208.555091] b43-phy0: Controller RESET (DMA error) ...
[  208.564569] b43-phy0 debug: Wireless interface stopped
[  208.565696] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  208.565922] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  208.567464] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  208.569308] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  208.571295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  208.573296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  208.719470] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  208.721858] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  210.102476] b43-phy0 debug: Chip initialized
[  210.102625] b43-phy0 debug: 64-bit DMA initialized
[  210.111510] Registered led device: b43-phy0::tx
[  210.111987] Registered led device: b43-phy0::rx
[  210.112488] Registered led device: b43-phy0::radio
[  210.112748] b43-phy0 debug: Wireless interface started
[  210.112753] b43-phy0: Controller restarted
[  210.112786] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  210.112792] b43-phy0: Controller RESET (DMA error) ...
[  210.112834] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  210.112839] b43-phy0: Controller RESET (DMA error) ...
[  210.112875] b43-phy0 debug: Wireless interface stopped
[  210.114523] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  210.114747] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  210.116291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  210.118293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  210.120295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  210.122299] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  210.268448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  210.270837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  211.651462] b43-phy0 debug: Chip initialized
[  211.651613] b43-phy0 debug: 64-bit DMA initialized
[  211.660505] Registered led device: b43-phy0::tx
[  211.660984] Registered led device: b43-phy0::rx
[  211.661488] Registered led device: b43-phy0::radio
[  211.661748] b43-phy0 debug: Wireless interface started
[  211.671569] b43-phy0 debug: Wireless interface stopped
[  211.672692] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  211.672917] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  211.674470] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  211.676293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  211.678293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  211.680293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  211.826448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  211.828837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  213.209479] b43-phy0 debug: Chip initialized
[  213.209644] b43-phy0 debug: 64-bit DMA initialized
[  213.218581] Registered led device: b43-phy0::tx
[  213.219437] Registered led device: b43-phy0::rx
[  213.219653] Registered led device: b43-phy0::radio
[  213.219724] b43-phy0 debug: Wireless interface started
[  213.219829] b43-phy0 debug: Wireless interface stopped
[  213.219933] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  213.220158] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  213.221265] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  213.223297] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  213.225307] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  213.227297] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  213.373446] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  213.375836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  214.756476] b43-phy0 debug: Chip initialized
[  214.756629] b43-phy0 debug: 64-bit DMA initialized
[  214.765527] Registered led device: b43-phy0::tx
[  214.766010] Registered led device: b43-phy0::rx
[  214.766486] Registered led device: b43-phy0::radio
[  214.766981] b43-phy0 debug: Wireless interface started
[  214.766985] __ratelimit: 10 callbacks suppressed
[  214.766987] b43-phy0: Controller restarted
[  214.767048] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  214.767054] b43-phy0: Controller RESET (DMA error) ...
[  214.767085] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  214.767089] b43-phy0: Controller RESET (DMA error) ...
[  214.767282] b43-phy0 debug: Wireless interface stopped
[  214.767933] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  214.768163] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  214.770470] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  214.772298] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  214.774293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  214.776293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  214.922447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  214.924832] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  216.310478] b43-phy0 debug: Chip initialized
[  216.310650] b43-phy0 debug: 64-bit DMA initialized
[  216.319576] Registered led device: b43-phy0::tx
[  216.320422] Registered led device: b43-phy0::rx
[  216.320637] Registered led device: b43-phy0::radio
[  216.320744] b43-phy0 debug: Wireless interface started
[  216.320748] b43-phy0: Controller restarted
[  216.320791] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  216.320797] b43-phy0: Controller RESET (DMA error) ...
[  216.320834] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  216.320839] b43-phy0: Controller RESET (DMA error) ...
[  216.320879] b43-phy0 debug: Wireless interface stopped
[  216.320982] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  216.321206] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  216.323271] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  216.325292] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  216.327294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  216.329293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  216.475460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  216.477849] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  217.858476] b43-phy0 debug: Chip initialized
[  217.858635] b43-phy0 debug: 64-bit DMA initialized
[  217.867517] Registered led device: b43-phy0::tx
[  217.867996] Registered led device: b43-phy0::rx
[  217.868493] Registered led device: b43-phy0::radio
[  217.868754] b43-phy0 debug: Wireless interface started
[  217.868863] b43-phy0 debug: Wireless interface stopped
[  217.870319] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  217.870543] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  217.872289] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  217.874293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  217.876296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  217.878295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  218.024449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  218.026838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  219.407477] b43-phy0 debug: Chip initialized
[  219.407630] b43-phy0 debug: 64-bit DMA initialized
[  219.416522] Registered led device: b43-phy0::tx
[  219.417001] Registered led device: b43-phy0::rx
[  219.417478] Registered led device: b43-phy0::radio
[  219.417973] b43-phy0 debug: Wireless interface started
[  219.418092] b43-phy0 debug: Wireless interface stopped
[  219.418766] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  219.418829] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  219.420268] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  219.422294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  219.424294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  219.426293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  219.573449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  219.575837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  220.963477] b43-phy0 debug: Chip initialized
[  220.963642] b43-phy0 debug: 64-bit DMA initialized
[  220.972586] Registered led device: b43-phy0::tx
[  220.973438] Registered led device: b43-phy0::rx
[  220.973653] Registered led device: b43-phy0::radio
[  220.973725] b43-phy0 debug: Wireless interface started
[  220.973759] __ratelimit: 10 callbacks suppressed
[  220.973761] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  220.973766] b43-phy0: Controller RESET (DMA error) ...
[  220.973770] b43-phy0: Controller restarted
[  220.973804] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  220.973809] b43-phy0: Controller RESET (DMA error) ...
[  220.973917] b43-phy0 debug: Wireless interface stopped
[  220.974026] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  220.974249] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  220.976282] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  220.978295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  220.980284] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  220.982295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  221.128477] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  221.130861] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  222.516512] b43-phy0 debug: Chip initialized
[  222.516689] b43-phy0 debug: 64-bit DMA initialized
[  222.527362] Registered led device: b43-phy0::tx
[  222.528181] Registered led device: b43-phy0::rx
[  222.528513] Registered led device: b43-phy0::radio
[  222.528775] b43-phy0 debug: Wireless interface started
[  222.528809] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  222.528814] b43-phy0: Controller RESET (DMA error) ...
[  222.528817] b43-phy0: Controller restarted
[  222.528851] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  222.528856] b43-phy0: Controller RESET (DMA error) ...
[  222.528911] b43-phy0 debug: Wireless interface stopped
[  222.529320] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  222.529545] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  222.531266] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  222.533283] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  222.535282] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  222.537285] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  222.696468] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  222.698859] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  224.081477] b43-phy0 debug: Chip initialized
[  224.081666] b43-phy0 debug: 64-bit DMA initialized
[  224.090624] Registered led device: b43-phy0::tx
[  224.091486] Registered led device: b43-phy0::rx
[  224.091701] Registered led device: b43-phy0::radio
[  224.091774] b43-phy0 debug: Wireless interface started
[  224.091812] b43-phy0 debug: Wireless interface stopped
[  224.091917] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  224.092145] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  224.093270] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  224.095290] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  224.097298] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  224.099294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  224.245448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  224.247838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  225.630464] b43-phy0 debug: Chip initialized
[  225.630622] b43-phy0 debug: 64-bit DMA initialized
[  225.639530] Registered led device: b43-phy0::tx
[  225.640018] Registered led device: b43-phy0::rx
[  225.640495] Registered led device: b43-phy0::radio
[  225.641030] b43-phy0 debug: Wireless interface started
[  225.641143] b43-phy0 debug: Wireless interface stopped
[  225.641834] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  225.642059] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  225.643287] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  225.645294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  225.647294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  225.649294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  225.795458] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  225.797845] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  227.180466] b43-phy0 debug: Chip initialized
[  227.180626] b43-phy0 debug: 64-bit DMA initialized
[  227.189216] Registered led device: b43-phy0::tx
[  227.189238] Registered led device: b43-phy0::rx
[  227.189789] Registered led device: b43-phy0::radio
[  227.190055] b43-phy0 debug: Wireless interface started
[  227.190061] __ratelimit: 6 callbacks suppressed
[  227.190063] b43-phy0: Controller restarted
[  227.190117] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  227.190123] b43-phy0: Controller RESET (DMA error) ...
[  227.190200] b43-phy0 debug: Wireless interface stopped
[  227.191760] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  227.191985] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  227.193296] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  227.195295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  227.197295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  227.199296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  227.345446] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  227.347836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  228.730463] b43-phy0 debug: Chip initialized
[  228.730613] b43-phy0 debug: 64-bit DMA initialized
[  228.739520] Registered led device: b43-phy0::tx
[  228.740007] Registered led device: b43-phy0::rx
[  228.740480] Registered led device: b43-phy0::radio
[  228.740974] b43-phy0 debug: Wireless interface started
[  228.740979] b43-phy0: Controller restarted
[  228.741020] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  228.741025] b43-phy0: Controller RESET (DMA error) ...
[  228.741056] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  228.741061] b43-phy0: Controller RESET (DMA error) ...
[  228.741100] b43-phy0 debug: Wireless interface stopped
[  228.742530] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  228.742569] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  228.744305] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  228.746315] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  228.748294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  228.750298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  228.896458] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  228.898847] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  230.281478] b43-phy0 debug: Chip initialized
[  230.281642] b43-phy0 debug: 64-bit DMA initialized
[  230.290570] Registered led device: b43-phy0::tx
[  230.291423] Registered led device: b43-phy0::rx
[  230.291639] Registered led device: b43-phy0::radio
[  230.291711] b43-phy0 debug: Wireless interface started
[  230.291714] b43-phy0: Controller restarted
[  230.291786] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  230.301569] b43-phy0 debug: Wireless interface stopped
[  230.301688] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  230.301914] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  230.303269] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  230.305293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  230.307294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  230.309293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  230.455448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  230.457835] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  231.840476] b43-phy0 debug: Chip initialized
[  231.840633] b43-phy0 debug: 64-bit DMA initialized
[  231.849517] Registered led device: b43-phy0::tx
[  231.849999] Registered led device: b43-phy0::rx
[  231.850501] Registered led device: b43-phy0::radio
[  231.850762] b43-phy0 debug: Wireless interface started
[  231.850856] b43-phy0 debug: Wireless interface stopped
[  231.852308] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  231.852532] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  231.854302] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  231.856309] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  231.858295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  231.860302] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  232.006448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  232.008838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  233.391478] b43-phy0 debug: Chip initialized
[  233.391631] b43-phy0 debug: 64-bit DMA initialized
[  233.400515] Registered led device: b43-phy0::tx
[  233.400991] Registered led device: b43-phy0::rx
[  233.401492] Registered led device: b43-phy0::radio
[  233.401752] b43-phy0 debug: Wireless interface started
[  233.401756] __ratelimit: 8 callbacks suppressed
[  233.401758] b43-phy0: Controller restarted
[  233.401810] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  233.401816] b43-phy0: Controller RESET (DMA error) ...
[  233.411569] b43-phy0 debug: Wireless interface stopped
[  233.412703] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  233.412929] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  233.414469] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  233.416308] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  233.418295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  233.420296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  233.567447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  233.569839] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  234.952465] b43-phy0 debug: Chip initialized
[  234.952617] b43-phy0 debug: 64-bit DMA initialized
[  234.961514] Registered led device: b43-phy0::tx
[  234.961992] Registered led device: b43-phy0::rx
[  234.962496] Registered led device: b43-phy0::radio
[  234.962757] b43-phy0 debug: Wireless interface started
[  234.962762] b43-phy0: Controller restarted
[  234.962791] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  234.962797] b43-phy0: Controller RESET (DMA error) ...
[  234.962831] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  234.962836] b43-phy0: Controller RESET (DMA error) ...
[  234.962873] b43-phy0 debug: Wireless interface stopped
[  234.964147] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  234.964387] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  234.966502] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  234.968300] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  234.970296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  234.972300] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  235.118450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  235.120837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  236.503464] b43-phy0 debug: Chip initialized
[  236.503620] b43-phy0 debug: 64-bit DMA initialized
[  236.512513] Registered led device: b43-phy0::tx
[  236.512995] Registered led device: b43-phy0::rx
[  236.513494] Registered led device: b43-phy0::radio
[  236.513754] b43-phy0 debug: Wireless interface started
[  236.513757] b43-phy0: Controller restarted
[  236.513815] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  236.523569] b43-phy0 debug: Wireless interface stopped
[  236.524694] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  236.524921] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  236.526466] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  236.528308] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  236.530295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  236.532295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  236.678461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  236.680848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  238.063476] b43-phy0 debug: Chip initialized
[  238.063629] b43-phy0 debug: 64-bit DMA initialized
[  238.072538] Registered led device: b43-phy0::tx
[  238.073020] Registered led device: b43-phy0::rx
[  238.073498] Registered led device: b43-phy0::radio
[  238.073991] b43-phy0 debug: Wireless interface started
[  238.074080] b43-phy0 debug: Wireless interface stopped
[  238.074783] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  238.075010] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  238.076502] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  238.078296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  238.080294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  238.082298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  238.228450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  238.230839] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  239.618465] b43-phy0 debug: Chip initialized
[  239.618634] b43-phy0 debug: 64-bit DMA initialized
[  239.627569] Registered led device: b43-phy0::tx
[  239.628425] Registered led device: b43-phy0::rx
[  239.628640] Registered led device: b43-phy0::radio
[  239.628712] b43-phy0 debug: Wireless interface started
[  239.628715] __ratelimit: 6 callbacks suppressed
[  239.628717] b43-phy0: Controller restarted
[  239.628755] b43-phy0 debug: Wireless interface stopped
[  239.628857] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  239.629084] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  239.630273] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  239.632290] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  239.634296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  239.636293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  239.782447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  239.784833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  241.167478] b43-phy0 debug: Chip initialized
[  241.167634] b43-phy0 debug: 64-bit DMA initialized
[  241.176515] Registered led device: b43-phy0::tx
[  241.176995] Registered led device: b43-phy0::rx
[  241.177499] Registered led device: b43-phy0::radio
[  241.177759] b43-phy0 debug: Wireless interface started
[  241.177764] b43-phy0: Controller restarted
[  241.177820] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  241.177826] b43-phy0: Controller RESET (DMA error) ...
[  241.187574] b43-phy0 debug: Wireless interface stopped
[  241.188700] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  241.188925] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  241.190463] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  241.192309] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  241.194295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  241.196296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  241.342449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  241.344838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  242.727463] b43-phy0 debug: Chip initialized
[  242.727617] b43-phy0 debug: 64-bit DMA initialized
[  242.736509] Registered led device: b43-phy0::tx
[  242.736986] Registered led device: b43-phy0::rx
[  242.737491] Registered led device: b43-phy0::radio
[  242.737751] b43-phy0 debug: Wireless interface started
[  242.737756] b43-phy0: Controller restarted
[  242.737789] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  242.737795] b43-phy0: Controller RESET (DMA error) ...
[  242.737837] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  242.737842] b43-phy0: Controller RESET (DMA error) ...
[  242.737878] b43-phy0 debug: Wireless interface stopped
[  242.739509] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  242.739734] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  242.741291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  242.743293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  242.745295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  242.747300] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  242.893448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  242.895835] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  244.278480] b43-phy0 debug: Chip initialized
[  244.278643] b43-phy0 debug: 64-bit DMA initialized
[  244.287582] Registered led device: b43-phy0::tx
[  244.288440] Registered led device: b43-phy0::rx
[  244.288656] Registered led device: b43-phy0::radio
[  244.288728] b43-phy0 debug: Wireless interface started
[  244.288731] b43-phy0: Controller restarted
[  244.298569] b43-phy0 debug: Wireless interface stopped
[  244.298687] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  244.298914] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  244.300269] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  244.302295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  244.304293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  244.306293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  244.452450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  244.454836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  245.837477] b43-phy0 debug: Chip initialized
[  245.837633] b43-phy0 debug: 64-bit DMA initialized
[  245.846505] Registered led device: b43-phy0::tx
[  245.846985] Registered led device: b43-phy0::rx
[  245.847841] Registered led device: b43-phy0::radio
[  245.848102] b43-phy0 debug: Wireless interface started
[  245.848180] b43-phy0 debug: Wireless interface stopped
[  245.848423] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  245.848646] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  245.850272] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  245.852295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  245.854293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  245.856298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  246.002447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  246.004837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  247.387478] b43-phy0 debug: Chip initialized
[  247.387631] b43-phy0 debug: 64-bit DMA initialized
[  247.396514] Registered led device: b43-phy0::tx
[  247.396992] Registered led device: b43-phy0::rx
[  247.397512] Registered led device: b43-phy0::radio
[  247.397772] b43-phy0 debug: Wireless interface started
[  247.397775] __ratelimit: 7 callbacks suppressed
[  247.397777] b43-phy0: Controller restarted
[  247.397830] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  247.397836] b43-phy0: Controller RESET (DMA error) ...
[  247.407569] b43-phy0 debug: Wireless interface stopped
[  247.408640] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  247.408867] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  247.410298] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  247.412294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  247.414293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  247.416294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  247.562463] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  247.564851] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  248.947465] b43-phy0 debug: Chip initialized
[  248.947616] b43-phy0 debug: 64-bit DMA initialized
[  248.956509] Registered led device: b43-phy0::tx
[  248.956985] Registered led device: b43-phy0::rx
[  248.957840] Registered led device: b43-phy0::radio
[  248.958100] b43-phy0 debug: Wireless interface started
[  248.958132] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  248.958136] b43-phy0: Controller RESET (DMA error) ...
[  248.958140] b43-phy0: Controller restarted
[  248.958175] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  248.958181] b43-phy0: Controller RESET (DMA error) ...
[  248.958214] b43-phy0 debug: Wireless interface stopped
[  248.958824] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  248.959050] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  248.960292] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  248.962293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  248.964294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  248.966298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  249.112449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  249.114839] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  250.512528] b43-phy0 debug: Chip initialized
[  250.512697] b43-phy0 debug: 64-bit DMA initialized
[  250.521232] Registered led device: b43-phy0::tx
[  250.521263] Registered led device: b43-phy0::rx
[  250.521286] Registered led device: b43-phy0::radio
[  250.521358] b43-phy0 debug: Wireless interface started
[  250.521387] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  250.521392] b43-phy0: Controller restarted
[  250.521430] b43-phy0 debug: Wireless interface stopped
[  250.521519] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  250.521550] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  250.523268] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  250.525303] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  250.527303] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  250.529294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  250.675462] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  250.677848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  252.060477] b43-phy0 debug: Chip initialized
[  252.060632] b43-phy0 debug: 64-bit DMA initialized
[  252.069517] Registered led device: b43-phy0::tx
[  252.069995] Registered led device: b43-phy0::rx
[  252.070500] Registered led device: b43-phy0::radio
[  252.070760] b43-phy0 debug: Wireless interface started
[  252.080569] b43-phy0 debug: Wireless interface stopped
[  252.081701] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  252.081926] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  252.083466] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  252.085309] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  252.087294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  252.089296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  252.235449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  252.237832] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  253.620466] b43-phy0 debug: Chip initialized
[  253.620620] b43-phy0 debug: 64-bit DMA initialized
[  253.629517] Registered led device: b43-phy0::tx
[  253.630002] Registered led device: b43-phy0::rx
[  253.630483] Registered led device: b43-phy0::radio
[  253.630975] b43-phy0 debug: Wireless interface started
[  253.630979] __ratelimit: 6 callbacks suppressed
[  253.630981] b43-phy0: Controller restarted
[  253.631018] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  253.631024] b43-phy0: Controller RESET (DMA error) ...
[  253.631057] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  253.631063] b43-phy0: Controller RESET (DMA error) ...
[  253.631099] b43-phy0 debug: Wireless interface stopped
[  253.632004] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  253.632303] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  253.634297] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  253.636294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  253.638293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  253.640297] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  253.786462] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  253.788850] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  255.171478] b43-phy0 debug: Chip initialized
[  255.171646] b43-phy0 debug: 64-bit DMA initialized
[  255.180228] Registered led device: b43-phy0::tx
[  255.180799] Registered led device: b43-phy0::rx
[  255.181021] Registered led device: b43-phy0::radio
[  255.181092] b43-phy0 debug: Wireless interface started
[  255.181097] b43-phy0: Controller restarted
[  255.181152] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  255.181158] b43-phy0: Controller RESET (DMA error) ...
[  255.190575] b43-phy0 debug: Wireless interface stopped
[  255.190693] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  255.190919] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  255.192267] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  255.194295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  255.196294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  255.198294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  255.344447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  255.346836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  256.729477] b43-phy0 debug: Chip initialized
[  256.729631] b43-phy0 debug: 64-bit DMA initialized
[  256.738514] Registered led device: b43-phy0::tx
[  256.738995] Registered led device: b43-phy0::rx
[  256.739497] Registered led device: b43-phy0::radio
[  256.739758] b43-phy0 debug: Wireless interface started
[  256.739763] b43-phy0: Controller restarted
[  256.739796] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  256.739870] b43-phy0 debug: Wireless interface stopped
[  256.740837] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  256.741065] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  256.742271] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  256.744300] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  256.746293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  256.748298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  256.894447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  256.896833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  258.279475] b43-phy0 debug: Chip initialized
[  258.279630] b43-phy0 debug: 64-bit DMA initialized
[  258.288520] Registered led device: b43-phy0::tx
[  258.289001] Registered led device: b43-phy0::rx
[  258.289478] Registered led device: b43-phy0::radio
[  258.289971] b43-phy0 debug: Wireless interface started
[  258.299568] b43-phy0 debug: Wireless interface stopped
[  258.300685] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  258.300910] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  258.302470] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  258.304293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  258.306293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  258.308293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  258.454460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  258.456850] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  259.839478] b43-phy0 debug: Chip initialized
[  259.839646] b43-phy0 debug: 64-bit DMA initialized
[  259.848578] Registered led device: b43-phy0::tx
[  259.849434] Registered led device: b43-phy0::rx
[  259.849649] Registered led device: b43-phy0::radio
[  259.849720] b43-phy0 debug: Wireless interface started
[  259.849724] __ratelimit: 6 callbacks suppressed
[  259.849726] b43-phy0: Controller restarted
[  259.849768] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  259.849774] b43-phy0: Controller RESET (DMA error) ...
[  259.849807] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  259.849812] b43-phy0: Controller RESET (DMA error) ...
[  259.849843] b43-phy0 debug: Wireless interface stopped
[  259.849956] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  259.850192] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  259.853211] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  259.854335] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  259.857211] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  259.858313] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  260.006443] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  260.008829] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  261.392471] b43-phy0 debug: Chip initialized
[  261.392628] b43-phy0 debug: 64-bit DMA initialized
[  261.401219] Registered led device: b43-phy0::tx
[  261.401279] Registered led device: b43-phy0::rx
[  261.401302] Registered led device: b43-phy0::radio
[  261.401373] b43-phy0 debug: Wireless interface started
[  261.401375] b43-phy0: 
[  261.401402] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  261.401407] b43-phy0: Controller RESET (DMA error) ...
[  261.401410] Controller restarted
[  261.401448] b43-phy0 debug: Wireless interface stopped
[  261.401532] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  261.401559] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  261.403016] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  261.405019] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  261.407221] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  261.409213] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  261.555443] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  261.557829] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  262.941458] b43-phy0 debug: Chip initialized
[  262.941615] b43-phy0 debug: 64-bit DMA initialized
[  262.950231] Registered led device: b43-phy0::tx
[  262.950256] Registered led device: b43-phy0::rx
[  262.950277] Registered led device: b43-phy0::radio
[  262.950346] b43-phy0 debug: Wireless interface started
[  262.950350] b43-phy0: Controller restarted
[  262.950425] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  262.959494] b43-phy0 debug: Wireless interface stopped
[  262.959610] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  262.959836] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  262.961017] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  262.963220] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  262.965218] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  262.967219] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  263.113451] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  263.115841] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  264.498457] b43-phy0 debug: Chip initialized
[  264.498611] b43-phy0 debug: 64-bit DMA initialized
[  264.507520] Registered led device: b43-phy0::tx
[  264.507920] Registered led device: b43-phy0::rx
[  264.508767] Registered led device: b43-phy0::radio
[  264.509040] b43-phy0 debug: Wireless interface started
[  264.509208] b43-phy0 debug: Wireless interface stopped
[  264.509313] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  264.509534] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  264.511019] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  264.513221] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  264.515218] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  264.517215] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  264.664453] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  264.666839] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  266.049469] b43-phy0 debug: Chip initialized
[  266.049633] b43-phy0 debug: 64-bit DMA initialized
[  266.058586] Registered led device: b43-phy0::tx
[  266.058950] Registered led device: b43-phy0::rx
[  266.059462] Registered led device: b43-phy0::radio
[  266.059956] b43-phy0 debug: Wireless interface started
[  266.059986] __ratelimit: 8 callbacks suppressed
[  266.059988] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  266.059993] b43-phy0: Controller RESET (DMA error) ...
[  266.059996] b43-phy0: Controller restarted
[  266.060024] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  266.060030] b43-phy0: Controller RESET (DMA error) ...
[  266.060821] b43-phy0 debug: Wireless interface stopped
[  266.060948] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  266.061189] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  266.063025] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  266.065219] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  266.067212] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  266.069214] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  266.215440] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  266.217827] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  267.600571] b43-phy0 debug: Chip initialized
[  267.600727] b43-phy0 debug: 64-bit DMA initialized
[  267.609218] Registered led device: b43-phy0::tx
[  267.609281] Registered led device: b43-phy0::rx
[  267.609304] Registered led device: b43-phy0::radio
[  267.609374] b43-phy0 debug: Wireless interface started
[  267.609377] b43-phy0: Controller restarted
[  267.609421] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  267.609427] b43-phy0: Controller RESET (DMA error) ...
[  267.609466] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  267.609470] b43-phy0: Controller RESET (DMA error) ...
[  267.609505] b43-phy0 debug: Wireless interface stopped
[  267.609596] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  267.609626] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  267.611274] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  267.613283] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  267.615292] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  267.617292] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  267.763448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  267.765839] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  269.148466] b43-phy0 debug: Chip initialized
[  269.148618] b43-phy0 debug: 64-bit DMA initialized
[  269.157212] Registered led device: b43-phy0::tx
[  269.157235] Registered led device: b43-phy0::rx
[  269.157782] Registered led device: b43-phy0::radio
[  269.158046] b43-phy0 debug: Wireless interface started
[  269.158971] b43-phy0 debug: Wireless interface stopped
[  269.159085] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  269.159320] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  269.161312] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  269.163306] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  269.165293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  269.167294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  269.313459] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  269.315845] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  270.698478] b43-phy0 debug: Chip initialized
[  270.698631] b43-phy0 debug: 64-bit DMA initialized
[  270.707510] Registered led device: b43-phy0::tx
[  270.707988] Registered led device: b43-phy0::rx
[  270.708494] Registered led device: b43-phy0::radio
[  270.708754] b43-phy0 debug: Wireless interface started
[  270.708824] b43-phy0 debug: Wireless interface stopped
[  270.710370] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  270.710593] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  270.712290] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  270.714294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  270.716296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  270.718295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  270.864448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  270.866837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  272.249464] b43-phy0 debug: Chip initialized
[  272.249617] b43-phy0 debug: 64-bit DMA initialized
[  272.258513] Registered led device: b43-phy0::tx
[  272.258997] Registered led device: b43-phy0::rx
[  272.259505] Registered led device: b43-phy0::radio
[  272.259765] b43-phy0 debug: Wireless interface started
[  272.259771] __ratelimit: 6 callbacks suppressed
[  272.259773] b43-phy0: Controller restarted
[  272.259805] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  272.259810] b43-phy0: Controller RESET (DMA error) ...
[  272.259845] b43-phy0 debug: Wireless interface stopped
[  272.261461] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  272.261686] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  272.263290] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  272.265293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  272.267295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  272.269295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  272.415447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  272.417833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  273.800462] b43-phy0 debug: Chip initialized
[  273.800614] b43-phy0 debug: 64-bit DMA initialized
[  273.809506] Registered led device: b43-phy0::tx
[  273.809981] Registered led device: b43-phy0::rx
[  273.810835] Registered led device: b43-phy0::radio
[  273.811096] b43-phy0 debug: Wireless interface started
[  273.811127] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  273.811131] b43-phy0: Controller RESET (DMA error) ...
[  273.811135] b43-phy0: Controller restarted
[  273.811169] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  273.811174] b43-phy0: Controller RESET (DMA error) ...
[  273.811211] b43-phy0 debug: Wireless interface stopped
[  273.811819] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  273.812046] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  273.813286] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  273.815293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  273.817294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  273.819294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  273.965448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  273.967836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  275.350476] b43-phy0 debug: Chip initialized
[  275.350628] b43-phy0 debug: 64-bit DMA initialized
[  275.359514] Registered led device: b43-phy0::tx
[  275.359992] Registered led device: b43-phy0::rx
[  275.360496] Registered led device: b43-phy0::radio
[  275.360756] b43-phy0 debug: Wireless interface started
[  275.360761] b43-phy0: Controller restarted
[  275.360795] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  275.360832] b43-phy0 debug: Wireless interface stopped
[  275.362380] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  275.362603] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  275.364292] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  275.366293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  275.368296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  275.370293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  275.516446] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  275.518834] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  276.901476] b43-phy0 debug: Chip initialized
[  276.901643] b43-phy0 debug: 64-bit DMA initialized
[  276.910588] Registered led device: b43-phy0::tx
[  276.911450] Registered led device: b43-phy0::rx
[  276.911666] Registered led device: b43-phy0::radio
[  276.911737] b43-phy0 debug: Wireless interface started
[  276.911777] b43-phy0 debug: Wireless interface stopped
[  276.911884] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  276.912112] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  276.913272] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  276.915290] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  276.917296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  276.919293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  277.065447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  277.067832] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  278.450475] b43-phy0 debug: Chip initialized
[  278.450631] b43-phy0 debug: 64-bit DMA initialized
[  278.459518] Registered led device: b43-phy0::tx
[  278.460000] Registered led device: b43-phy0::rx
[  278.460509] Registered led device: b43-phy0::radio
[  278.460769] b43-phy0 debug: Wireless interface started
[  278.460775] __ratelimit: 2 callbacks suppressed
[  278.460777] b43-phy0: Controller restarted
[  278.460805] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  278.460811] b43-phy0: Controller RESET (DMA error) ...
[  278.460871] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  278.460876] b43-phy0: Controller RESET (DMA error) ...
[  278.460973] b43-phy0 debug: Wireless interface stopped
[  278.462701] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  278.462970] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  278.464301] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  278.466295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  278.468293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  278.470293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  278.617446] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  278.619837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  280.002480] b43-phy0 debug: Chip initialized
[  280.002632] b43-phy0 debug: 64-bit DMA initialized
[  280.011517] Registered led device: b43-phy0::tx
[  280.011996] Registered led device: b43-phy0::rx
[  280.012502] Registered led device: b43-phy0::radio
[  280.012761] b43-phy0 debug: Wireless interface started
[  280.012766] b43-phy0: Controller restarted
[  280.012797] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  280.012803] b43-phy0: Controller RESET (DMA error) ...
[  280.012840] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  280.012844] b43-phy0: Controller RESET (DMA error) ...
[  280.012885] b43-phy0 debug: Wireless interface stopped
[  280.014102] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  280.014343] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  280.016501] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  280.018294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  280.020296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  280.022295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  280.168450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  280.170838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  281.553464] b43-phy0 debug: Chip initialized
[  281.553619] b43-phy0 debug: 64-bit DMA initialized
[  281.562511] Registered led device: b43-phy0::tx
[  281.562992] Registered led device: b43-phy0::rx
[  281.563501] Registered led device: b43-phy0::radio
[  281.563761] b43-phy0 debug: Wireless interface started
[  281.563926] b43-phy0 debug: Wireless interface stopped
[  281.565378] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  281.565602] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  281.567301] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  281.569294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  281.571464] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  281.573295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  281.719459] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  281.721849] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  283.104476] b43-phy0 debug: Chip initialized
[  283.104630] b43-phy0 debug: 64-bit DMA initialized
[  283.113539] Registered led device: b43-phy0::tx
[  283.114027] Registered led device: b43-phy0::rx
[  283.114508] Registered led device: b43-phy0::radio
[  283.115001] b43-phy0 debug: Wireless interface started
[  283.115093] b43-phy0 debug: Wireless interface stopped
[  283.115591] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  283.115817] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  283.117504] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  283.119296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  283.121293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  283.123299] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  283.269462] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  283.271848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  284.654476] b43-phy0 debug: Chip initialized
[  284.654629] b43-phy0 debug: 64-bit DMA initialized
[  284.663210] Registered led device: b43-phy0::tx
[  284.663233] Registered led device: b43-phy0::rx
[  284.663773] Registered led device: b43-phy0::radio
[  284.664037] b43-phy0 debug: Wireless interface started
[  284.664041] __ratelimit: 10 callbacks suppressed
[  284.664043] b43-phy0: Controller restarted
[  284.664074] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  284.664079] b43-phy0: Controller RESET (DMA error) ...
[  284.664113] b43-phy0 debug: Wireless interface stopped
[  284.664210] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  284.664445] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  284.667509] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  284.669304] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  284.671293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  284.673294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  284.819458] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  284.821848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  286.204478] b43-phy0 debug: Chip initialized
[  286.204631] b43-phy0 debug: 64-bit DMA initialized
[  286.213512] Registered led device: b43-phy0::tx
[  286.213993] Registered led device: b43-phy0::rx
[  286.214500] Registered led device: b43-phy0::radio
[  286.214759] b43-phy0 debug: Wireless interface started
[  286.214764] b43-phy0: Controller restarted
[  286.214821] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  286.214826] b43-phy0: Controller RESET (DMA error) ...
[  286.224569] b43-phy0 debug: Wireless interface stopped
[  286.225701] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  286.225926] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  286.227469] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  286.229308] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  286.231294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  286.233296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  286.379448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  286.381836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  287.764476] b43-phy0 debug: Chip initialized
[  287.764632] b43-phy0 debug: 64-bit DMA initialized
[  287.773510] Registered led device: b43-phy0::tx
[  287.773985] Registered led device: b43-phy0::rx
[  287.774842] Registered led device: b43-phy0::radio
[  287.775103] b43-phy0 debug: Wireless interface started
[  287.775136] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  287.775140] b43-phy0: Controller RESET (DMA error) ...
[  287.775144] b43-phy0: Controller restarted
[  287.775179] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  287.775214] b43-phy0 debug: Wireless interface stopped
[  287.775811] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  287.776038] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  287.777291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  287.779294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  287.781293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  287.783298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  287.929447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  287.931836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  289.314479] b43-phy0 debug: Chip initialized
[  289.314644] b43-phy0 debug: 64-bit DMA initialized
[  289.323581] Registered led device: b43-phy0::tx
[  289.324446] Registered led device: b43-phy0::rx
[  289.324662] Registered led device: b43-phy0::radio
[  289.324733] b43-phy0 debug: Wireless interface started
[  289.324771] b43-phy0 debug: Wireless interface stopped
[  289.324876] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  289.325103] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  289.326267] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  289.328289] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  289.330299] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  289.332293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  289.478460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  289.480850] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  290.863478] b43-phy0 debug: Chip initialized
[  290.863635] b43-phy0 debug: 64-bit DMA initialized
[  290.872518] Registered led device: b43-phy0::tx
[  290.872995] Registered led device: b43-phy0::rx
[  290.873498] Registered led device: b43-phy0::radio
[  290.873758] b43-phy0 debug: Wireless interface started
[  290.873762] __ratelimit: 2 callbacks suppressed
[  290.873764] b43-phy0: Controller restarted
[  290.873817] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  290.873822] b43-phy0: Controller RESET (DMA error) ...
[  290.883569] b43-phy0 debug: Wireless interface stopped
[  290.884705] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  290.884932] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  290.886464] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  290.888308] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  290.890295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  290.892296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  291.038451] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  291.040840] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  292.423477] b43-phy0 debug: Chip initialized
[  292.423632] b43-phy0 debug: 64-bit DMA initialized
[  292.432507] Registered led device: b43-phy0::tx
[  292.432978] Registered led device: b43-phy0::rx
[  292.433839] Registered led device: b43-phy0::radio
[  292.434100] b43-phy0 debug: Wireless interface started
[  292.434103] b43-phy0: 
[  292.434130] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  292.434135] b43-phy0: Controller RESET (DMA error) ...
[  292.434138] Controller restarted
[  292.434183] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  292.434188] b43-phy0: Controller RESET (DMA error) ...
[  292.434218] b43-phy0 debug: Wireless interface stopped
[  292.434854] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  292.435082] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  292.436291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  292.438295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  292.440294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  292.442298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  292.588448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  292.591350] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  293.973475] b43-phy0 debug: Chip initialized
[  293.973627] b43-phy0 debug: 64-bit DMA initialized
[  293.982511] Registered led device: b43-phy0::tx
[  293.982991] Registered led device: b43-phy0::rx
[  293.983487] Registered led device: b43-phy0::radio
[  293.983746] b43-phy0 debug: Wireless interface started
[  293.983751] b43-phy0: Controller restarted
[  293.983786] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  293.983823] b43-phy0 debug: Wireless interface stopped
[  293.985343] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  293.985567] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  293.987291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  293.989294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  293.991295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  293.993295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  294.139447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  294.141838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  295.524465] b43-phy0 debug: Chip initialized
[  295.524617] b43-phy0 debug: 64-bit DMA initialized
[  295.533515] Registered led device: b43-phy0::tx
[  295.533994] Registered led device: b43-phy0::rx
[  295.534500] Registered led device: b43-phy0::radio
[  295.534760] b43-phy0 debug: Wireless interface started
[  295.544569] b43-phy0 debug: Wireless interface stopped
[  295.545695] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  295.545922] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  295.547463] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  295.549309] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  295.551295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  295.553295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  295.700462] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  295.702853] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  297.085478] b43-phy0 debug: Chip initialized
[  297.085630] b43-phy0 debug: 64-bit DMA initialized
[  297.094506] Registered led device: b43-phy0::tx
[  297.094982] Registered led device: b43-phy0::rx
[  297.095835] Registered led device: b43-phy0::radio
[  297.096095] b43-phy0 debug: Wireless interface started
[  297.096127] __ratelimit: 4 callbacks suppressed
[  297.096129] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  297.096134] b43-phy0: Controller RESET (DMA error) ...
[  297.096137] b43-phy0: Controller restarted
[  297.096172] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  297.096178] b43-phy0: Controller RESET (DMA error) ...
[  297.096211] b43-phy0 debug: Wireless interface stopped
[  297.096850] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  297.097077] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  297.098289] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  297.100295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  297.102294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  297.104298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  297.250448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  297.252837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  298.635466] b43-phy0 debug: Chip initialized
[  298.635619] b43-phy0 debug: 64-bit DMA initialized
[  298.644517] Registered led device: b43-phy0::tx
[  298.644998] Registered led device: b43-phy0::rx
[  298.645496] Registered led device: b43-phy0::radio
[  298.645756] b43-phy0 debug: Wireless interface started
[  298.645759] b43-phy0: Controller restarted
[  298.645792] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  298.645798] b43-phy0: Controller RESET (DMA error) ...
[  298.645832] b43-phy0 debug: Wireless interface stopped
[  298.647399] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  298.647623] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  298.649284] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  298.651302] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  298.653295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  298.655294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  298.801449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  298.803837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  300.186478] b43-phy0 debug: Chip initialized
[  300.186645] b43-phy0 debug: 64-bit DMA initialized
[  300.195584] Registered led device: b43-phy0::tx
[  300.196439] Registered led device: b43-phy0::rx
[  300.196655] Registered led device: b43-phy0::radio
[  300.196726] b43-phy0 debug: Wireless interface started
[  300.196729] b43-phy0: Controller restarted
[  300.196801] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  300.206569] b43-phy0 debug: Wireless interface stopped
[  300.206688] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  300.206914] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  300.208268] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  300.210293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  300.212294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  300.214294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  300.360448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  300.362838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  301.745465] b43-phy0 debug: Chip initialized
[  301.745620] b43-phy0 debug: 64-bit DMA initialized
[  301.754514] Registered led device: b43-phy0::tx
[  301.754995] Registered led device: b43-phy0::rx
[  301.755500] Registered led device: b43-phy0::radio
[  301.755761] b43-phy0 debug: Wireless interface started
[  301.755853] b43-phy0 debug: Wireless interface stopped
[  301.757304] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  301.757528] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  301.759302] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  301.761293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  301.763295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  301.765299] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  301.911449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  301.913836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  303.296476] b43-phy0 debug: Chip initialized
[  303.296628] b43-phy0 debug: 64-bit DMA initialized
[  303.305506] Registered led device: b43-phy0::tx
[  303.305982] Registered led device: b43-phy0::rx
[  303.306836] Registered led device: b43-phy0::radio
[  303.307096] b43-phy0 debug: Wireless interface started
[  303.307128] __ratelimit: 6 callbacks suppressed
[  303.307130] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  303.307135] b43-phy0: Controller RESET (DMA error) ...
[  303.307139] b43-phy0: Controller restarted
[  303.307167] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  303.307172] b43-phy0: Controller RESET (DMA error) ...
[  303.316568] b43-phy0 debug: Wireless interface stopped
[  303.316684] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  303.316910] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  303.318270] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  303.320293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  303.322294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  303.324293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  303.470447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  303.472836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  304.855478] b43-phy0 debug: Chip initialized
[  304.855630] b43-phy0 debug: 64-bit DMA initialized
[  304.864509] Registered led device: b43-phy0::tx
[  304.864988] Registered led device: b43-phy0::rx
[  304.865487] Registered led device: b43-phy0::radio
[  304.865746] b43-phy0 debug: Wireless interface started
[  304.865749] b43-phy0: Controller restarted
[  304.865781] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  304.865787] b43-phy0: Controller RESET (DMA error) ...
[  304.865825] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  304.865830] b43-phy0: Controller RESET (DMA error) ...
[  304.865866] b43-phy0 debug: Wireless interface stopped
[  304.867493] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  304.867717] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  304.869291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  304.871293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  304.873296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  304.875299] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  305.021463] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  305.023849] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  306.406477] b43-phy0 debug: Chip initialized
[  306.406629] b43-phy0 debug: 64-bit DMA initialized
[  306.415517] Registered led device: b43-phy0::tx
[  306.415995] Registered led device: b43-phy0::rx
[  306.416505] Registered led device: b43-phy0::radio
[  306.416764] b43-phy0 debug: Wireless interface started
[  306.426569] b43-phy0 debug: Wireless interface stopped
[  306.427694] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  306.427920] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  306.429466] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  306.431308] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  306.433295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  306.435295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  306.581448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  306.583834] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  307.966475] b43-phy0 debug: Chip initialized
[  307.966628] b43-phy0 debug: 64-bit DMA initialized
[  307.975505] Registered led device: b43-phy0::tx
[  307.975980] Registered led device: b43-phy0::rx
[  307.976838] Registered led device: b43-phy0::radio
[  307.977098] b43-phy0 debug: Wireless interface started
[  307.977196] b43-phy0 debug: Wireless interface stopped
[  307.977628] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  307.977851] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  307.979278] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  307.981295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  307.983294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  307.985298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  308.131450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  308.133840] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  309.516465] b43-phy0 debug: Chip initialized
[  309.516618] b43-phy0 debug: 64-bit DMA initialized
[  309.525516] Registered led device: b43-phy0::tx
[  309.525995] Registered led device: b43-phy0::rx
[  309.526499] Registered led device: b43-phy0::radio
[  309.526758] b43-phy0 debug: Wireless interface started
[  309.526763] __ratelimit: 10 callbacks suppressed
[  309.526765] b43-phy0: Controller restarted
[  309.526798] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  309.526803] b43-phy0: Controller RESET (DMA error) ...
[  309.526838] b43-phy0 debug: Wireless interface stopped
[  309.528421] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  309.528645] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  309.530290] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  309.532293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  309.534296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  309.536295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  309.683461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  309.685845] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  311.068476] b43-phy0 debug: Chip initialized
[  311.068628] b43-phy0 debug: 64-bit DMA initialized
[  311.077503] Registered led device: b43-phy0::tx
[  311.077979] Registered led device: b43-phy0::rx
[  311.078845] Registered led device: b43-phy0::radio
[  311.079107] b43-phy0 debug: Wireless interface started
[  311.079140] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  311.079145] b43-phy0: Controller RESET (DMA error) ...
[  311.079148] b43-phy0: Controller restarted
[  311.079203] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  311.079208] b43-phy0: Controller RESET (DMA error) ...
[  311.088569] b43-phy0 debug: Wireless interface stopped
[  311.088684] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  311.088909] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  311.090270] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  311.092293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  311.094294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  311.096294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  311.242447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  311.244833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  312.627479] b43-phy0 debug: Chip initialized
[  312.627646] b43-phy0 debug: 64-bit DMA initialized
[  312.636584] Registered led device: b43-phy0::tx
[  312.637437] Registered led device: b43-phy0::rx
[  312.637652] Registered led device: b43-phy0::radio
[  312.637724] b43-phy0 debug: Wireless interface started
[  312.637729] b43-phy0: Controller restarted
[  312.637772] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  312.637843] b43-phy0 debug: Wireless interface stopped
[  312.637948] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  312.638173] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  312.639268] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  312.641284] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  312.643300] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  312.645300] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  312.791447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  312.793837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  314.176478] b43-phy0 debug: Chip initialized
[  314.176631] b43-phy0 debug: 64-bit DMA initialized
[  314.185509] Registered led device: b43-phy0::tx
[  314.185990] Registered led device: b43-phy0::rx
[  314.186495] Registered led device: b43-phy0::radio
[  314.186756] b43-phy0 debug: Wireless interface started
[  314.196569] b43-phy0 debug: Wireless interface stopped
[  314.197694] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  314.197920] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  314.199469] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  314.201308] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  314.203294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  314.205295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  314.351450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  314.353836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  315.736477] b43-phy0 debug: Chip initialized
[  315.736631] b43-phy0 debug: 64-bit DMA initialized
[  315.745508] Registered led device: b43-phy0::tx
[  315.745985] Registered led device: b43-phy0::rx
[  315.746841] Registered led device: b43-phy0::radio
[  315.747103] b43-phy0 debug: Wireless interface started
[  315.747107] __ratelimit: 6 callbacks suppressed
[  315.747138] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  315.747142] b43-phy0: Controller RESET (DMA error) ...
[  315.747145] b43-phy0: Controller restarted
[  315.747190] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  315.747195] b43-phy0: Controller RESET (DMA error) ...
[  315.747225] b43-phy0 debug: Wireless interface stopped
[  315.747863] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  315.748091] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  315.749318] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  315.751293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  315.753294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  315.755298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  315.901447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  315.903835] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  317.286479] b43-phy0 debug: Chip initialized
[  317.286630] b43-phy0 debug: 64-bit DMA initialized
[  317.295512] Registered led device: b43-phy0::tx
[  317.295988] Registered led device: b43-phy0::rx
[  317.296490] Registered led device: b43-phy0::radio
[  317.296750] b43-phy0 debug: Wireless interface started
[  317.296753] b43-phy0: Controller restarted
[  317.296786] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  317.296792] b43-phy0: Controller RESET (DMA error) ...
[  317.296823] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  317.296827] b43-phy0: Controller RESET (DMA error) ...
[  317.296862] b43-phy0 debug: Wireless interface stopped
[  317.298295] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  317.298521] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  317.300303] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  317.302294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  317.304295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  317.306295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  317.452450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  317.454833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  318.837464] b43-phy0 debug: Chip initialized
[  318.837616] b43-phy0 debug: 64-bit DMA initialized
[  318.846521] Registered led device: b43-phy0::tx
[  318.847001] Registered led device: b43-phy0::rx
[  318.847479] Registered led device: b43-phy0::radio
[  318.847973] b43-phy0 debug: Wireless interface started
[  318.857569] b43-phy0 debug: Wireless interface stopped
[  318.858695] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  318.858921] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  318.860466] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  318.862309] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  318.864294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  318.866296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  319.012469] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  319.014856] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  320.397463] b43-phy0 debug: Chip initialized
[  320.397616] b43-phy0 debug: 64-bit DMA initialized
[  320.406501] Registered led device: b43-phy0::tx
[  320.406977] Registered led device: b43-phy0::rx
[  320.407828] Registered led device: b43-phy0::radio
[  320.408089] b43-phy0 debug: Wireless interface started
[  320.408184] b43-phy0 debug: Wireless interface stopped
[  320.408617] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  320.408840] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  320.410271] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  320.412304] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  320.414302] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  320.416299] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  320.562450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  320.564840] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  321.947464] b43-phy0 debug: Chip initialized
[  321.947617] b43-phy0 debug: 64-bit DMA initialized
[  321.956507] Registered led device: b43-phy0::tx
[  321.956983] Registered led device: b43-phy0::rx
[  321.957837] Registered led device: b43-phy0::radio
[  321.958098] b43-phy0 debug: Wireless interface started
[  321.958102] __ratelimit: 8 callbacks suppressed
[  321.958132] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  321.958136] b43-phy0: Controller RESET (DMA error) ...
[  321.958139] b43-phy0: Controller restarted
[  321.958210] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  321.958215] b43-phy0: Controller RESET (DMA error) ...
[  321.967568] b43-phy0 debug: Wireless interface stopped
[  321.967686] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  321.967912] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  321.969269] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  321.971292] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  321.973294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  321.975293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  322.121449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  322.123837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  323.506467] b43-phy0 debug: Chip initialized
[  323.506631] b43-phy0 debug: 64-bit DMA initialized
[  323.515586] Registered led device: b43-phy0::tx
[  323.516450] Registered led device: b43-phy0::rx
[  323.516665] Registered led device: b43-phy0::radio
[  323.516737] b43-phy0 debug: Wireless interface started
[  323.516740] b43-phy0: Controller restarted
[  323.516783] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  323.516789] b43-phy0: Controller RESET (DMA error) ...
[  323.516820] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  323.516825] b43-phy0: Controller RESET (DMA error) ...
[  323.516860] b43-phy0 debug: Wireless interface stopped
[  323.516965] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  323.517191] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  323.518267] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  323.520297] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  323.522300] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  323.524300] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  323.670449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  323.672838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  325.055475] b43-phy0 debug: Chip initialized
[  325.055631] b43-phy0 debug: 64-bit DMA initialized
[  325.064521] Registered led device: b43-phy0::tx
[  325.065013] Registered led device: b43-phy0::rx
[  325.065489] Registered led device: b43-phy0::radio
[  325.065981] b43-phy0 debug: Wireless interface started
[  325.066248] b43-phy0 debug: Wireless interface stopped
[  325.066699] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  325.066928] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  325.068288] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  325.070295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  325.072294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  325.074293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  325.220463] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  325.222850] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  326.605477] b43-phy0 debug: Chip initialized
[  326.605628] b43-phy0 debug: 64-bit DMA initialized
[  326.614210] Registered led device: b43-phy0::tx
[  326.614233] Registered led device: b43-phy0::rx
[  326.615332] Registered led device: b43-phy0::radio
[  326.615593] b43-phy0 debug: Wireless interface started
[  326.615695] b43-phy0 debug: Wireless interface stopped
[  326.615806] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  326.616031] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  326.617268] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  326.619283] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  326.621297] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  326.623295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  326.769449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  326.771838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  328.159477] b43-phy0 debug: Chip initialized
[  328.159646] b43-phy0 debug: 64-bit DMA initialized
[  328.168550] Registered led device: b43-phy0::tx
[  328.169011] Registered led device: b43-phy0::rx
[  328.169225] Registered led device: b43-phy0::radio
[  328.169632] b43-phy0 debug: Wireless interface started
[  328.169636] __ratelimit: 10 callbacks suppressed
[  328.169638] b43-phy0: Controller restarted
[  328.169663] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  328.169668] b43-phy0: Controller RESET (DMA error) ...
[  328.169701] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  328.169706] b43-phy0: Controller RESET (DMA error) ...
[  328.170068] b43-phy0 debug: Wireless interface stopped
[  328.170181] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  328.170409] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  328.173214] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  328.175210] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  328.176314] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  328.179209] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  328.324440] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  328.326825] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  329.709471] b43-phy0 debug: Chip initialized
[  329.709627] b43-phy0 debug: 64-bit DMA initialized
[  329.718221] Registered led device: b43-phy0::tx
[  329.718285] Registered led device: b43-phy0::rx
[  329.718308] Registered led device: b43-phy0::radio
[  329.718378] b43-phy0 debug: Wireless interface started
[  329.718380] b43-phy0: Controller restarted
[  329.718426] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  329.718432] b43-phy0: Controller RESET (DMA error) ...
[  329.718470] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  329.718475] b43-phy0: Controller RESET (DMA error) ...
[  329.718510] b43-phy0 debug: Wireless interface stopped
[  329.718602] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  329.718633] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  329.720274] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  329.722287] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  329.724294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  329.726291] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  329.872458] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  329.874844] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  331.257465] b43-phy0 debug: Chip initialized
[  331.257620] b43-phy0 debug: 64-bit DMA initialized
[  331.266218] Registered led device: b43-phy0::tx
[  331.266241] Registered led device: b43-phy0::rx
[  331.266789] Registered led device: b43-phy0::radio
[  331.267055] b43-phy0 debug: Wireless interface started
[  331.267980] b43-phy0 debug: Wireless interface stopped
[  331.268089] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  331.268325] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  331.270314] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  331.272306] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  331.274293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  331.276295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  331.422459] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  331.424849] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  332.807475] b43-phy0 debug: Chip initialized
[  332.807627] b43-phy0 debug: 64-bit DMA initialized
[  332.816513] Registered led device: b43-phy0::tx
[  332.816993] Registered led device: b43-phy0::rx
[  332.817493] Registered led device: b43-phy0::radio
[  332.817753] b43-phy0 debug: Wireless interface started
[  332.817820] b43-phy0 debug: Wireless interface stopped
[  332.819363] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  332.819588] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  332.821295] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  332.823294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  332.825294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  332.827293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  332.973445] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  332.975830] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  334.358479] b43-phy0 debug: Chip initialized
[  334.358645] b43-phy0 debug: 64-bit DMA initialized
[  334.367579] Registered led device: b43-phy0::tx
[  334.368430] Registered led device: b43-phy0::rx
[  334.368646] Registered led device: b43-phy0::radio
[  334.368718] b43-phy0 debug: Wireless interface started
[  334.368723] __ratelimit: 6 callbacks suppressed
[  334.368725] b43-phy0: Controller restarted
[  334.368764] b43-phy0 debug: Wireless interface stopped
[  334.368868] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  334.369095] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  334.370267] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  334.372303] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  334.374308] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  334.376294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  334.522445] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  334.524833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  335.907478] b43-phy0 debug: Chip initialized
[  335.907631] b43-phy0 debug: 64-bit DMA initialized
[  335.916512] Registered led device: b43-phy0::tx
[  335.916992] Registered led device: b43-phy0::rx
[  335.917493] Registered led device: b43-phy0::radio
[  335.917754] b43-phy0 debug: Wireless interface started
[  335.917759] b43-phy0: Controller restarted
[  335.917790] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  335.917796] b43-phy0: Controller RESET (DMA error) ...
[  335.917858] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  335.917863] b43-phy0: Controller RESET (DMA error) ...
[  335.917960] b43-phy0 debug: Wireless interface stopped
[  335.918696] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  335.918922] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  335.920287] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  335.922294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  335.924297] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  335.926294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  336.072461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  336.074849] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  337.457463] b43-phy0 debug: Chip initialized
[  337.457616] b43-phy0 debug: 64-bit DMA initialized
[  337.466513] Registered led device: b43-phy0::tx
[  337.466993] Registered led device: b43-phy0::rx
[  337.467493] Registered led device: b43-phy0::radio
[  337.467754] b43-phy0 debug: Wireless interface started
[  337.467759] b43-phy0: Controller restarted
[  337.467787] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  337.467793] b43-phy0: Controller RESET (DMA error) ...
[  337.467855] b43-phy0 debug: Wireless interface stopped
[  337.468830] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  337.469055] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  337.470274] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  337.472294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  337.474293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  337.476293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  337.622448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  337.624837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  339.007463] b43-phy0 debug: Chip initialized
[  339.007619] b43-phy0 debug: 64-bit DMA initialized
[  339.016520] Registered led device: b43-phy0::tx
[  339.017000] Registered led device: b43-phy0::rx
[  339.017481] Registered led device: b43-phy0::radio
[  339.017976] b43-phy0 debug: Wireless interface started
[  339.017980] b43-phy0: Controller restarted
[  339.018113] b43-phy0 debug: Wireless interface stopped
[  339.018827] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  339.019056] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  339.020289] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  339.022297] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  339.024293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  339.026294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  339.172459] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  339.174849] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  340.557478] b43-phy0 debug: Chip initialized
[  340.557632] b43-phy0 debug: 64-bit DMA initialized
[  340.566213] Registered led device: b43-phy0::tx
[  340.566235] Registered led device: b43-phy0::rx
[  340.566784] Registered led device: b43-phy0::radio
[  340.567050] b43-phy0 debug: Wireless interface started
[  340.567996] b43-phy0 debug: Wireless interface stopped
[  340.568104] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  340.568339] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  340.570297] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  340.572306] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  340.574294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  340.576299] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  340.723451] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  340.725840] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  342.108463] b43-phy0 debug: Chip initialized
[  342.108631] b43-phy0 debug: 64-bit DMA initialized
[  342.117570] Registered led device: b43-phy0::tx
[  342.118427] Registered led device: b43-phy0::rx
[  342.118642] Registered led device: b43-phy0::radio
[  342.118713] b43-phy0 debug: Wireless interface started
[  342.118716] __ratelimit: 7 callbacks suppressed
[  342.118718] b43-phy0: Controller restarted
[  342.118790] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  342.118796] b43-phy0: Controller RESET (DMA error) ...
[  342.118831] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  342.118836] b43-phy0: Controller RESET (DMA error) ...
[  342.128570] b43-phy0 debug: Wireless interface stopped
[  342.128689] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  342.128917] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  342.130268] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  342.132293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  342.134294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  342.136293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  342.282461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  342.284849] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  343.667478] b43-phy0 debug: Chip initialized
[  343.667636] b43-phy0 debug: 64-bit DMA initialized
[  343.676513] Registered led device: b43-phy0::tx
[  343.677350] Registered led device: b43-phy0::rx
[  343.677565] Registered led device: b43-phy0::radio
[  343.677636] b43-phy0 debug: Wireless interface started
[  343.677640] b43-phy0: Controller restarted
[  343.677684] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  343.677690] b43-phy0: Controller RESET (DMA error) ...
[  343.677724] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  343.677729] b43-phy0: Controller RESET (DMA error) ...
[  343.677763] b43-phy0 debug: Wireless interface stopped
[  343.677870] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  343.678095] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  343.679272] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  343.681284] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  343.683297] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  343.685301] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  343.831447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  343.833838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  345.216467] b43-phy0 debug: Chip initialized
[  345.216633] b43-phy0 debug: 64-bit DMA initialized
[  345.225586] Registered led device: b43-phy0::tx
[  345.226444] Registered led device: b43-phy0::rx
[  345.226659] Registered led device: b43-phy0::radio
[  345.226729] b43-phy0 debug: Wireless interface started
[  345.236570] b43-phy0 debug: Wireless interface stopped
[  345.236687] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  345.236914] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  345.238279] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  345.240295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  345.242294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  345.244293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  345.390449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  345.392846] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  346.775477] b43-phy0 debug: Chip initialized
[  346.775642] b43-phy0 debug: 64-bit DMA initialized
[  346.784561] Registered led device: b43-phy0::tx
[  346.785409] Registered led device: b43-phy0::rx
[  346.785624] Registered led device: b43-phy0::radio
[  346.785696] b43-phy0 debug: Wireless interface started
[  346.785795] b43-phy0 debug: Wireless interface stopped
[  346.785908] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  346.786146] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  346.789214] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  346.791212] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  346.792312] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  346.795212] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  346.940439] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  346.942826] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  348.325458] b43-phy0 debug: Chip initialized
[  348.325612] b43-phy0 debug: 64-bit DMA initialized
[  348.334229] Registered led device: b43-phy0::tx
[  348.334291] Registered led device: b43-phy0::rx
[  348.334315] Registered led device: b43-phy0::radio
[  348.334385] b43-phy0 debug: Wireless interface started
[  348.334388] __ratelimit: 10 callbacks suppressed
[  348.334390] b43-phy0: Controller restarted
[  348.334429] b43-phy0 debug: Wireless interface stopped
[  348.334513] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  348.334544] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  348.336017] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  348.338023] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  348.340223] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  348.342214] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  348.489451] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  348.491840] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  349.874457] b43-phy0 debug: Chip initialized
[  349.874607] b43-phy0 debug: 64-bit DMA initialized
[  349.883505] Registered led device: b43-phy0::tx
[  349.883902] Registered led device: b43-phy0::rx
[  349.884773] Registered led device: b43-phy0::radio
[  349.885295] b43-phy0 debug: Wireless interface started
[  349.885329] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  349.885334] b43-phy0: Controller RESET (DMA error) ...
[  349.885337] b43-phy0: Controller restarted
[  349.885394] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  349.885400] b43-phy0: Controller RESET (DMA error) ...
[  349.894487] b43-phy0 debug: Wireless interface stopped
[  349.894601] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  349.894826] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  349.896017] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  349.898212] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  349.900227] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  349.902212] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  350.049454] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  350.051836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  351.440458] b43-phy0 debug: Chip initialized
[  351.440627] b43-phy0 debug: 64-bit DMA initialized
[  351.449589] Registered led device: b43-phy0::tx
[  351.450436] Registered led device: b43-phy0::rx
[  351.450652] Registered led device: b43-phy0::radio
[  351.450723] b43-phy0 debug: Wireless interface started
[  351.450726] b43-phy0: Controller restarted
[  351.450771] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  351.450777] b43-phy0: Controller RESET (DMA error) ...
[  351.450810] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  351.450843] b43-phy0 debug: Wireless interface stopped
[  351.450955] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  351.451179] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  351.453285] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  351.455292] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  351.457292] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  351.459296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  351.605459] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  351.607848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  352.990466] b43-phy0 debug: Chip initialized
[  352.990620] b43-phy0 debug: 64-bit DMA initialized
[  352.999221] Registered led device: b43-phy0::tx
[  352.999244] Registered led device: b43-phy0::rx
[  352.999786] Registered led device: b43-phy0::radio
[  353.000052] b43-phy0 debug: Wireless interface started
[  353.000976] b43-phy0 debug: Wireless interface stopped
[  353.001088] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  353.001326] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  353.003312] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  353.005306] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  353.007293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  353.009294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  353.155461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  353.157851] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  354.540475] b43-phy0 debug: Chip initialized
[  354.540628] b43-phy0 debug: 64-bit DMA initialized
[  354.549502] Registered led device: b43-phy0::tx
[  354.549978] Registered led device: b43-phy0::rx
[  354.550835] Registered led device: b43-phy0::radio
[  354.551096] b43-phy0 debug: Wireless interface started
[  354.560568] b43-phy0 debug: Wireless interface stopped
[  354.560682] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  354.560908] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  354.562269] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  354.564295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  354.566294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  354.568294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  354.714446] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  354.716837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  356.099465] b43-phy0 debug: Chip initialized
[  356.099614] b43-phy0 debug: 64-bit DMA initialized
[  356.108504] Registered led device: b43-phy0::tx
[  356.108979] Registered led device: b43-phy0::rx
[  356.109833] Registered led device: b43-phy0::radio
[  356.110095] b43-phy0 debug: Wireless interface started
[  356.110128] __ratelimit: 9 callbacks suppressed
[  356.110130] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  356.110135] b43-phy0: Controller RESET (DMA error) ...
[  356.110138] b43-phy0: Controller restarted
[  356.110174] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  356.110179] b43-phy0: Controller RESET (DMA error) ...
[  356.110212] b43-phy0 debug: Wireless interface stopped
[  356.110855] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  356.111083] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  356.112291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  356.114296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  356.116294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  356.118298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  356.264494] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  356.266915] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  357.649475] b43-phy0 debug: Chip initialized
[  357.649631] b43-phy0 debug: 64-bit DMA initialized
[  357.658519] Registered led device: b43-phy0::tx
[  357.658998] Registered led device: b43-phy0::rx
[  357.659498] Registered led device: b43-phy0::radio
[  357.659758] b43-phy0 debug: Wireless interface started
[  357.659762] b43-phy0: Controller restarted
[  357.659794] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  357.659800] b43-phy0: Controller RESET (DMA error) ...
[  357.659834] b43-phy0 debug: Wireless interface stopped
[  357.661390] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  357.661615] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  357.663292] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  357.665293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  357.667295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  357.669295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  357.816459] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  357.818850] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  359.201478] b43-phy0 debug: Chip initialized
[  359.201629] b43-phy0 debug: 64-bit DMA initialized
[  359.210511] Registered led device: b43-phy0::tx
[  359.210992] Registered led device: b43-phy0::rx
[  359.211494] Registered led device: b43-phy0::radio
[  359.211755] b43-phy0 debug: Wireless interface started
[  359.211758] b43-phy0: Controller restarted
[  359.211816] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  359.221569] b43-phy0 debug: Wireless interface stopped
[  359.222700] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  359.222926] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  359.224464] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  359.226309] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  359.228295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  359.230296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  359.376450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  359.378839] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  360.761478] b43-phy0 debug: Chip initialized
[  360.761642] b43-phy0 debug: 64-bit DMA initialized
[  360.770545] Registered led device: b43-phy0::tx
[  360.771036] Registered led device: b43-phy0::rx
[  360.771511] Registered led device: b43-phy0::radio
[  360.772005] b43-phy0 debug: Wireless interface started
[  360.772114] b43-phy0 debug: Wireless interface stopped
[  360.772831] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  360.773059] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  360.774291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  360.776294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  360.778294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  360.780298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  360.926460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  360.928847] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  362.311479] b43-phy0 debug: Chip initialized
[  362.311645] b43-phy0 debug: 64-bit DMA initialized
[  362.320228] Registered led device: b43-phy0::tx
[  362.320796] Registered led device: b43-phy0::rx
[  362.321019] Registered led device: b43-phy0::radio
[  362.321092] b43-phy0 debug: Wireless interface started
[  362.321098] __ratelimit: 6 callbacks suppressed
[  362.321100] b43-phy0: Controller restarted
[  362.321154] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  362.321160] b43-phy0: Controller RESET (DMA error) ...
[  362.330575] b43-phy0 debug: Wireless interface stopped
[  362.330694] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  362.330922] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  362.332273] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  362.334295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  362.336293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  362.338293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  362.484449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  362.486837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  363.869463] b43-phy0 debug: Chip initialized
[  363.869615] b43-phy0 debug: 64-bit DMA initialized
[  363.878506] Registered led device: b43-phy0::tx
[  363.878987] Registered led device: b43-phy0::rx
[  363.879489] Registered led device: b43-phy0::radio
[  363.879749] b43-phy0 debug: Wireless interface started
[  363.879754] b43-phy0: Controller restarted
[  363.879787] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  363.879793] b43-phy0: Controller RESET (DMA error) ...
[  363.879835] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  363.879840] b43-phy0: Controller RESET (DMA error) ...
[  363.879877] b43-phy0 debug: Wireless interface stopped
[  363.881522] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  363.881747] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  363.883291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  363.885294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  363.887296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  363.889300] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  364.035455] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  364.037845] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  365.420466] b43-phy0 debug: Chip initialized
[  365.420618] b43-phy0 debug: 64-bit DMA initialized
[  365.429512] Registered led device: b43-phy0::tx
[  365.429993] Registered led device: b43-phy0::rx
[  365.430500] Registered led device: b43-phy0::radio
[  365.430760] b43-phy0 debug: Wireless interface started
[  365.430762] b43-phy0: Controller restarted
[  365.430817] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  365.440569] b43-phy0 debug: Wireless interface stopped
[  365.441693] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  365.441920] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  365.443464] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  365.445309] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  365.447493] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  365.449295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  365.595449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  365.597840] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  366.980463] b43-phy0 debug: Chip initialized
[  366.980617] b43-phy0 debug: 64-bit DMA initialized
[  366.989514] Registered led device: b43-phy0::tx
[  366.989996] Registered led device: b43-phy0::rx
[  366.990498] Registered led device: b43-phy0::radio
[  366.990759] b43-phy0 debug: Wireless interface started
[  366.990865] b43-phy0 debug: Wireless interface stopped
[  366.992325] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  366.992550] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  366.994290] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  366.996293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  366.998295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  367.000300] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  367.146462] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  367.148851] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  368.531462] b43-phy0 debug: Chip initialized
[  368.531616] b43-phy0 debug: 64-bit DMA initialized
[  368.540528] Registered led device: b43-phy0::tx
[  368.541013] Registered led device: b43-phy0::rx
[  368.541487] Registered led device: b43-phy0::radio
[  368.541978] b43-phy0 debug: Wireless interface started
[  368.541982] __ratelimit: 6 callbacks suppressed
[  368.541984] b43-phy0: Controller restarted
[  368.542040] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  368.542046] b43-phy0: Controller RESET (DMA error) ...
[  368.542076] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  368.542080] b43-phy0: Controller RESET (DMA error) ...
[  368.551568] b43-phy0 debug: Wireless interface stopped
[  368.552685] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  368.552912] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  368.554465] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  368.556293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  368.558293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  368.560293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  368.706459] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  368.708848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  370.091466] b43-phy0 debug: Chip initialized
[  370.091619] b43-phy0 debug: 64-bit DMA initialized
[  370.100514] Registered led device: b43-phy0::tx
[  370.100998] Registered led device: b43-phy0::rx
[  370.101501] Registered led device: b43-phy0::radio
[  370.101761] b43-phy0 debug: Wireless interface started
[  370.101766] b43-phy0: Controller restarted
[  370.101799] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  370.101805] b43-phy0: Controller RESET (DMA error) ...
[  370.101847] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  370.101852] b43-phy0: Controller RESET (DMA error) ...
[  370.101890] b43-phy0 debug: Wireless interface stopped
[  370.102635] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  370.102859] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  370.104510] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  370.106305] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  370.108294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  370.110298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  370.256461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  370.258847] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  371.646476] b43-phy0 debug: Chip initialized
[  371.646640] b43-phy0 debug: 64-bit DMA initialized
[  371.655558] Registered led device: b43-phy0::tx
[  371.656415] Registered led device: b43-phy0::rx
[  371.656630] Registered led device: b43-phy0::radio
[  371.656702] b43-phy0 debug: Wireless interface started
[  371.666569] b43-phy0 debug: Wireless interface stopped
[  371.666687] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  371.666915] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  371.668280] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  371.670296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  371.672294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  371.674293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  371.821460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  371.823852] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  373.206479] b43-phy0 debug: Chip initialized
[  373.206646] b43-phy0 debug: 64-bit DMA initialized
[  373.215585] Registered led device: b43-phy0::tx
[  373.216444] Registered led device: b43-phy0::rx
[  373.216660] Registered led device: b43-phy0::radio
[  373.216767] b43-phy0 debug: Wireless interface started
[  373.216870] b43-phy0 debug: Wireless interface stopped
[  373.216974] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  373.217199] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  373.219291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  373.221294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  373.223294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  373.225298] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  373.371449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  373.373838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  374.756475] b43-phy0 debug: Chip initialized
[  374.756628] b43-phy0 debug: 64-bit DMA initialized
[  374.765513] Registered led device: b43-phy0::tx
[  374.765992] Registered led device: b43-phy0::rx
[  374.766515] Registered led device: b43-phy0::radio
[  374.766776] b43-phy0 debug: Wireless interface started
[  374.766780] __ratelimit: 10 callbacks suppressed
[  374.766782] b43-phy0: Controller restarted
[  374.766835] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  374.766841] b43-phy0: Controller RESET (DMA error) ...
[  374.776568] b43-phy0 debug: Wireless interface stopped
[  374.777645] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  374.777872] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  374.779298] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  374.781294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  374.783293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  374.785293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  374.931447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  374.933836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  376.316478] b43-phy0 debug: Chip initialized
[  376.316632] b43-phy0 debug: 64-bit DMA initialized
[  376.325508] Registered led device: b43-phy0::tx
[  376.325988] Registered led device: b43-phy0::rx
[  376.326493] Registered led device: b43-phy0::radio
[  376.326753] b43-phy0 debug: Wireless interface started
[  376.326758] b43-phy0: Controller restarted
[  376.326792] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000400, 0x00000000, 0x00000000
[  376.326798] b43-phy0: Controller RESET (DMA error) ...
[  376.326849] b43-phy0 debug: Wireless interface stopped
[  376.328204] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  376.328446] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  376.330303] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  376.332293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  376.334296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  376.336299] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  376.482449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  376.484839] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  377.867464] b43-phy0 debug: Chip initialized
[  377.867619] b43-phy0 debug: 64-bit DMA initialized
[  377.876512] Registered led device: b43-phy0::tx
[  377.876993] Registered led device: b43-phy0::rx
[  377.877496] Registered led device: b43-phy0::radio
[  377.877756] b43-phy0 debug: Wireless interface started
[  377.877760] b43-phy0: Controller restarted
[  377.877809] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  377.877815] b43-phy0: Controller RESET (DMA error) ...
[  377.877995] b43-phy0 debug: Wireless interface stopped
[  377.878536] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  377.878762] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  377.880270] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  377.882294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  377.884294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  377.886294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  378.032460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  378.034851] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  379.417478] b43-phy0 debug: Chip initialized
[  379.417632] b43-phy0 debug: 64-bit DMA initialized
[  379.426546] Registered led device: b43-phy0::tx
[  379.427028] Registered led device: b43-phy0::rx
[  379.427510] Registered led device: b43-phy0::radio
[  379.428003] b43-phy0 debug: Wireless interface started
[  379.428032] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  379.428097] b43-phy0 debug: Wireless interface stopped
[  379.428839] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  379.429066] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  379.431297] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  379.433295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  379.435293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  379.437294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  379.583449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  379.585837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  380.968476] b43-phy0 debug: Chip initialized
[  380.968628] b43-phy0 debug: 64-bit DMA initialized
[  380.977208] Registered led device: b43-phy0::tx
[  380.977230] Registered led device: b43-phy0::rx
[  380.978340] Registered led device: b43-phy0::radio
[  380.978600] b43-phy0 debug: Wireless interface started
[  380.978604] __ratelimit: 4 callbacks suppressed
[  380.978606] b43-phy0: Controller restarted
[  380.978636] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  380.978642] b43-phy0: Controller RESET (DMA error) ...
[  380.978676] b43-phy0 debug: Wireless interface stopped
[  380.978785] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  380.979015] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  380.981509] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  380.983306] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  380.985297] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  380.987295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  381.133447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  381.135833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  382.518465] b43-phy0 debug: Chip initialized
[  382.518618] b43-phy0 debug: 64-bit DMA initialized
[  382.527505] Registered led device: b43-phy0::tx
[  382.527986] Registered led device: b43-phy0::rx
[  382.528486] Registered led device: b43-phy0::radio
[  382.528746] b43-phy0 debug: Wireless interface started
[  382.528751] b43-phy0: Controller restarted
[  382.528786] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  382.528791] b43-phy0: Controller RESET (DMA error) ...
[  382.528825] b43-phy0 debug: Wireless interface stopped
[  382.530384] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  382.530609] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  382.532291] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  382.534294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  382.536295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  382.538295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  382.684449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  382.686835] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  384.069476] b43-phy0 debug: Chip initialized
[  384.069627] b43-phy0 debug: 64-bit DMA initialized
[  384.078507] Registered led device: b43-phy0::tx
[  384.078981] Registered led device: b43-phy0::rx
[  384.079837] Registered led device: b43-phy0::radio
[  384.080098] b43-phy0 debug: Wireless interface started
[  384.080129] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  384.080133] b43-phy0: Controller RESET (DMA error) ...
[  384.080136] b43-phy0: Controller restarted
[  384.080170] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  384.080210] b43-phy0 debug: Wireless interface stopped
[  384.080785] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  384.081013] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  384.082281] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  384.084293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  384.086294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  384.088294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  384.234448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  384.236836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  385.619466] b43-phy0 debug: Chip initialized
[  385.619633] b43-phy0 debug: 64-bit DMA initialized
[  385.628594] Registered led device: b43-phy0::tx
[  385.629455] Registered led device: b43-phy0::rx
[  385.629670] Registered led device: b43-phy0::radio
[  385.629740] b43-phy0 debug: Wireless interface started
[  385.629778] b43-phy0 debug: Wireless interface stopped
[  385.629882] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  385.630110] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  385.631273] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  385.633291] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  385.635297] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  385.637294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  385.784461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  385.786850] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  387.169474] b43-phy0 debug: Chip initialized
[  387.169631] b43-phy0 debug: 64-bit DMA initialized
[  387.178521] Registered led device: b43-phy0::tx
[  387.179001] Registered led device: b43-phy0::rx
[  387.179479] Registered led device: b43-phy0::radio
[  387.179971] b43-phy0 debug: Wireless interface started
[  387.179975] __ratelimit: 2 callbacks suppressed
[  387.179977] b43-phy0: Controller restarted
[  387.180011] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  387.180017] b43-phy0: Controller RESET (DMA error) ...
[  387.180056] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  387.180061] b43-phy0: Controller RESET (DMA error) ...
[  387.180102] b43-phy0 debug: Wireless interface stopped
[  387.181024] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  387.181270] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  387.183296] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  387.185294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  387.187293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  387.189293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  387.335462] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  387.337851] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  388.720477] b43-phy0 debug: Chip initialized
[  388.720628] b43-phy0 debug: 64-bit DMA initialized
[  388.729208] Registered led device: b43-phy0::tx
[  388.729230] Registered led device: b43-phy0::rx
[  388.730342] Registered led device: b43-phy0::radio
[  388.730603] b43-phy0 debug: Wireless interface started
[  388.730606] b43-phy0: Controller restarted
[  388.730633] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  388.730639] b43-phy0: Controller RESET (DMA error) ...
[  388.730672] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  388.730677] b43-phy0: Controller RESET (DMA error) ...
[  388.730716] b43-phy0 debug: Wireless interface stopped
[  388.730825] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  388.731051] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  388.733311] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  388.735296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  388.737294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  388.739294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  388.885445] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  388.887833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  390.270478] b43-phy0 debug: Chip initialized
[  390.270632] b43-phy0 debug: 64-bit DMA initialized
[  390.279510] Registered led device: b43-phy0::tx
[  390.279991] Registered led device: b43-phy0::rx
[  390.280492] Registered led device: b43-phy0::radio
[  390.280751] b43-phy0 debug: Wireless interface started
[  390.280865] b43-phy0 debug: Wireless interface stopped
[  390.282966] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  390.283199] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  390.284295] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  390.286299] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  390.288295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  390.290293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  390.436448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  390.438834] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  391.821477] b43-phy0 debug: Chip initialized
[  391.821629] b43-phy0 debug: 64-bit DMA initialized
[  391.830528] Registered led device: b43-phy0::tx
[  391.831032] Registered led device: b43-phy0::rx
[  391.831488] Registered led device: b43-phy0::radio
[  391.831980] b43-phy0 debug: Wireless interface started
[  391.832074] b43-phy0 debug: Wireless interface stopped
[  391.833563] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  391.833791] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  391.835296] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  391.837296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  391.839295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  391.841293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  391.987459] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  391.989846] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  393.372476] b43-phy0 debug: Chip initialized
[  393.372627] b43-phy0 debug: 64-bit DMA initialized
[  393.381521] Registered led device: b43-phy0::tx
[  393.382012] Registered led device: b43-phy0::rx
[  393.382485] Registered led device: b43-phy0::radio
[  393.382977] b43-phy0 debug: Wireless interface started
[  393.382981] __ratelimit: 10 callbacks suppressed
[  393.382983] b43-phy0: Controller restarted
[  393.383022] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  393.383027] b43-phy0: Controller RESET (DMA error) ...
[  393.383061] b43-phy0 debug: Wireless interface stopped
[  393.383172] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  393.383410] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  393.385497] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  393.387296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  393.389293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  393.391293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  393.537448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  393.539836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  394.927477] b43-phy0 debug: Chip initialized
[  394.927642] b43-phy0 debug: 64-bit DMA initialized
[  394.936558] Registered led device: b43-phy0::tx
[  394.937404] Registered led device: b43-phy0::rx
[  394.937619] Registered led device: b43-phy0::radio
[  394.937691] b43-phy0 debug: Wireless interface started
[  394.937694] b43-phy0: Controller restarted
[  394.937733] b43-phy0 debug: Wireless interface stopped
[  394.937836] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  394.938063] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  394.939273] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  394.941283] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  394.943296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  394.945295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  395.091463] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  395.093852] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  396.476465] b43-phy0 debug: Chip initialized
[  396.476631] b43-phy0 debug: 64-bit DMA initialized
[  396.485580] Registered led device: b43-phy0::tx
[  396.486449] Registered led device: b43-phy0::rx
[  396.486664] Registered led device: b43-phy0::radio
[  396.486734] b43-phy0 debug: Wireless interface started
[  396.486739] b43-phy0: Controller restarted
[  396.486783] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  396.486788] b43-phy0: Controller RESET (DMA error) ...
[  396.486826] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  396.486831] b43-phy0: Controller RESET (DMA error) ...
[  396.486876] b43-phy0 debug: Wireless interface stopped
[  396.486988] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  396.487214] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  396.489288] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  396.491295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  396.493297] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  396.495295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  396.641447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  396.643852] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  397.749038] CE: hpet increasing min_delta_ns to 15000 nsec
[  398.026475] b43-phy0 debug: Chip initialized
[  398.026641] b43-phy0 debug: 64-bit DMA initialized
[  398.035558] Registered led device: b43-phy0::tx
[  398.036350] Registered led device: b43-phy0::rx
[  398.036566] Registered led device: b43-phy0::radio
[  398.036637] b43-phy0 debug: Wireless interface started
[  398.036640] b43-phy0: Controller restarted
[  398.036748] b43-phy0 debug: Wireless interface stopped
[  398.036861] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  398.037099] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  398.040246] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  398.041331] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  398.044209] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  398.045308] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  398.194441] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  398.196830] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  399.579455] b43-phy0 debug: Chip initialized
[  399.579614] b43-phy0 debug: 64-bit DMA initialized
[  399.588238] Registered led device: b43-phy0::tx
[  399.588263] Registered led device: b43-phy0::rx
[  399.588286] Registered led device: b43-phy0::radio
[  399.588357] b43-phy0 debug: Wireless interface started
[  399.588360] __ratelimit: 4 callbacks suppressed
[  399.588362] b43-phy0: Controller restarted
[  399.588400] b43-phy0 debug: Wireless interface stopped
[  399.588485] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  399.588515] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  399.590017] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  399.592023] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  399.594222] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  399.596221] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  399.743442] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  399.745826] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  401.128468] b43-phy0 debug: Chip initialized
[  401.128632] b43-phy0 debug: 64-bit DMA initialized
[  401.137559] Registered led device: b43-phy0::tx
[  401.137920] Registered led device: b43-phy0::rx
[  401.138420] Registered led device: b43-phy0::radio
[  401.138911] b43-phy0 debug: Wireless interface started
[  401.138915] b43-phy0: 
[  401.138947] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  401.138952] b43-phy0: Controller RESET (DMA error) ...
[  401.138955] Controller restarted
[  401.138983] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  401.138988] b43-phy0: Controller RESET (DMA error) ...
[  401.139040] b43-phy0 debug: Wireless interface stopped
[  401.139775] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  401.140018] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  401.142216] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  401.144218] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  401.146211] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  401.148213] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  401.294442] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  401.296828] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  402.680458] b43-phy0 debug: Chip initialized
[  402.680612] b43-phy0 debug: 64-bit DMA initialized
[  402.689231] Registered led device: b43-phy0::tx
[  402.689256] Registered led device: b43-phy0::rx
[  402.689280] Registered led device: b43-phy0::radio
[  402.689349] b43-phy0 debug: Wireless interface started
[  402.689353] b43-phy0: Controller restarted
[  402.689401] b43-phy0 debug: Wireless interface stopped
[  402.689486] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  402.689517] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  402.691017] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  402.693024] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  402.695224] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  402.697215] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  402.844452] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  402.846841] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  404.229458] b43-phy0 debug: Chip initialized
[  404.229613] b43-phy0 debug: 64-bit DMA initialized
[  404.238521] Registered led device: b43-phy0::tx
[  404.238919] Registered led device: b43-phy0::rx
[  404.239767] Registered led device: b43-phy0::radio
[  404.240039] b43-phy0 debug: Wireless interface started
[  404.240042] b43-phy0: Controller restarted
[  404.240087] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  404.240093] b43-phy0: Controller RESET (DMA error) ...
[  404.240507] b43-phy0 debug: Wireless interface stopped
[  404.240615] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  404.240838] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  404.242016] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  404.244219] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  404.246213] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  404.248211] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  404.395454] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  404.397842] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  405.780456] b43-phy0 debug: Chip initialized
[  405.780606] b43-phy0 debug: 64-bit DMA initialized
[  405.789517] Registered led device: b43-phy0::tx
[  405.789910] Registered led device: b43-phy0::rx
[  405.790754] Registered led device: b43-phy0::radio
[  405.791027] b43-phy0 debug: Wireless interface started
[  405.791187] b43-phy0 debug: Wireless interface stopped
[  405.791294] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  405.791518] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  405.793019] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  405.795223] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  405.797217] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  405.799213] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  405.946453] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  405.948834] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  407.332460] b43-phy0 debug: Chip initialized
[  407.332627] b43-phy0 debug: 64-bit DMA initialized
[  407.341604] Registered led device: b43-phy0::tx
[  407.342458] Registered led device: b43-phy0::rx
[  407.342673] Registered led device: b43-phy0::radio
[  407.342745] b43-phy0 debug: Wireless interface started
[  407.342748] __ratelimit: 7 callbacks suppressed
[  407.342750] b43-phy0: Controller restarted
[  407.342793] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  407.342799] b43-phy0: Controller RESET (DMA error) ...
[  407.342837] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  407.342842] b43-phy0: Controller RESET (DMA error) ...
[  407.342877] b43-phy0 debug: Wireless interface stopped
[  407.342989] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  407.343215] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  407.345271] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  407.347293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  407.349292] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  407.351292] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  407.497460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  407.499846] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  408.882476] b43-phy0 debug: Chip initialized
[  408.882633] b43-phy0 debug: 64-bit DMA initialized
[  408.891215] Registered led device: b43-phy0::tx
[  408.891238] Registered led device: b43-phy0::rx
[  408.891776] Registered led device: b43-phy0::radio
[  408.892041] b43-phy0 debug: Wireless interface started
[  408.892046] b43-phy0: Controller restarted
[  408.892078] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  408.892083] b43-phy0: Controller RESET (DMA error) ...
[  408.892117] b43-phy0 debug: Wireless interface stopped
[  408.892211] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  408.892447] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  408.895481] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  408.897295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  408.899293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  408.901294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  409.047453] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  409.049841] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  410.432477] b43-phy0 debug: Chip initialized
[  410.432634] b43-phy0 debug: 64-bit DMA initialized
[  410.441217] Registered led device: b43-phy0::tx
[  410.441240] Registered led device: b43-phy0::rx
[  410.441781] Registered led device: b43-phy0::radio
[  410.442045] b43-phy0 debug: Wireless interface started
[  410.442050] b43-phy0: Controller restarted
[  410.442081] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  410.442118] b43-phy0 debug: Wireless interface stopped
[  410.442214] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  410.442448] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  410.445475] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  410.447295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  410.449293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  410.451293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  410.597446] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  410.599833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  411.982463] b43-phy0 debug: Chip initialized
[  411.982624] b43-phy0 debug: 64-bit DMA initialized
[  411.991223] Registered led device: b43-phy0::tx
[  411.991245] Registered led device: b43-phy0::rx
[  411.991369] Registered led device: b43-phy0::radio
[  411.991628] b43-phy0 debug: Wireless interface started
[  411.991724] b43-phy0 debug: Wireless interface stopped
[  411.991817] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  411.991886] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  411.993269] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  411.995496] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  411.997301] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  411.999294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  412.145447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  412.147871] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  413.535476] b43-phy0 debug: Chip initialized
[  413.535643] b43-phy0 debug: 64-bit DMA initialized
[  413.544231] Registered led device: b43-phy0::tx
[  413.544321] Registered led device: b43-phy0::rx
[  413.544535] Registered led device: b43-phy0::radio
[  413.544607] b43-phy0 debug: Wireless interface started
[  413.544610] __ratelimit: 6 callbacks suppressed
[  413.544641] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  413.544646] b43-phy0: Controller RESET (DMA error) ...
[  413.544649] b43-phy0: Controller restarted
[  413.544683] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  413.544688] b43-phy0: Controller RESET (DMA error) ...
[  413.544723] b43-phy0 debug: Wireless interface stopped
[  413.544818] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  413.544887] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  413.546276] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  413.548469] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  413.550295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  413.552294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  413.698446] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  413.700835] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  415.083475] b43-phy0 debug: Chip initialized
[  415.083631] b43-phy0 debug: 64-bit DMA initialized
[  415.092220] Registered led device: b43-phy0::tx
[  415.092242] Registered led device: b43-phy0::rx
[  415.092365] Registered led device: b43-phy0::radio
[  415.092624] b43-phy0 debug: Wireless interface started
[  415.092627] b43-phy0: Controller restarted
[  415.092654] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  415.092659] b43-phy0: Controller RESET (DMA error) ...
[  415.092696] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  415.092701] b43-phy0: Controller RESET (DMA error) ...
[  415.092736] b43-phy0 debug: Wireless interface stopped
[  415.092832] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  415.092901] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  415.094276] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  415.096297] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  415.098295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  415.100294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  415.246446] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  415.248835] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  416.631477] b43-phy0 debug: Chip initialized
[  416.631634] b43-phy0 debug: 64-bit DMA initialized
[  416.640219] Registered led device: b43-phy0::tx
[  416.640242] Registered led device: b43-phy0::rx
[  416.640365] Registered led device: b43-phy0::radio
[  416.640624] b43-phy0 debug: Wireless interface started
[  416.640688] b43-phy0 debug: Wireless interface stopped
[  416.640781] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  416.640850] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  416.642275] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  416.644284] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  416.646295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  416.648293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  416.794460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  416.796845] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  418.179467] b43-phy0 debug: Chip initialized
[  418.179634] b43-phy0 debug: 64-bit DMA initialized
[  418.188230] Registered led device: b43-phy0::tx
[  418.188261] Registered led device: b43-phy0::rx
[  418.188375] Registered led device: b43-phy0::radio
[  418.188636] b43-phy0 debug: Wireless interface started
[  418.188732] b43-phy0 debug: Wireless interface stopped
[  418.188829] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  418.189054] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  418.191275] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  418.193296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  418.195293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  418.197293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  418.343459] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  418.345848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  419.733475] b43-phy0 debug: Chip initialized
[  419.733641] b43-phy0 debug: 64-bit DMA initialized
[  419.742228] Registered led device: b43-phy0::tx
[  419.742317] Registered led device: b43-phy0::rx
[  419.742531] Registered led device: b43-phy0::radio
[  419.742603] b43-phy0 debug: Wireless interface started
[  419.742606] __ratelimit: 8 callbacks suppressed
[  419.742636] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  419.742641] b43-phy0: Controller RESET (DMA error) ...
[  419.742644] b43-phy0: Controller restarted
[  419.742678] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  419.742684] b43-phy0: Controller RESET (DMA error) ...
[  419.742718] b43-phy0 debug: Wireless interface stopped
[  419.742812] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  419.742881] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  419.744276] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  419.746463] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  419.748295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  419.750293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  419.897461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  419.899848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  421.282462] b43-phy0 debug: Chip initialized
[  421.282620] b43-phy0 debug: 64-bit DMA initialized
[  421.291219] Registered led device: b43-phy0::tx
[  421.291242] Registered led device: b43-phy0::rx
[  421.291367] Registered led device: b43-phy0::radio
[  421.291626] b43-phy0 debug: Wireless interface started
[  421.291629] b43-phy0: Controller restarted
[  421.291659] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  421.291664] b43-phy0: Controller RESET (DMA error) ...
[  421.291701] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  421.291706] b43-phy0: Controller RESET (DMA error) ...
[  421.291741] b43-phy0 debug: Wireless interface stopped
[  421.291836] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  421.291904] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  421.293276] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  421.295298] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  421.297295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  421.299294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  421.445461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  421.447848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  422.830475] b43-phy0 debug: Chip initialized
[  422.830640] b43-phy0 debug: 64-bit DMA initialized
[  422.839230] Registered led device: b43-phy0::tx
[  422.839319] Registered led device: b43-phy0::rx
[  422.839533] Registered led device: b43-phy0::radio
[  422.839604] b43-phy0 debug: Wireless interface started
[  422.839668] b43-phy0 debug: Wireless interface stopped
[  422.839762] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  422.839829] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  422.841285] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  422.843495] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  422.845295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  422.847294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  422.993447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  422.995834] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  424.378466] b43-phy0 debug: Chip initialized
[  424.378620] b43-phy0 debug: 64-bit DMA initialized
[  424.387237] Registered led device: b43-phy0::tx
[  424.387329] Registered led device: b43-phy0::rx
[  424.387542] Registered led device: b43-phy0::radio
[  424.387612] b43-phy0 debug: Wireless interface started
[  424.387680] b43-phy0 debug: Wireless interface stopped
[  424.388560] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  424.388784] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  424.390266] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  424.392302] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  424.394295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  424.396293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  424.542448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  424.544836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  425.927463] b43-phy0 debug: Chip initialized
[  425.927629] b43-phy0 debug: 64-bit DMA initialized
[  425.936228] Registered led device: b43-phy0::tx
[  425.936341] Registered led device: b43-phy0::rx
[  425.936556] Registered led device: b43-phy0::radio
[  425.936627] b43-phy0 debug: Wireless interface started
[  425.936631] __ratelimit: 6 callbacks suppressed
[  425.936661] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  425.936665] b43-phy0: Controller RESET (DMA error) ...
[  425.936669] b43-phy0: Controller restarted
[  425.936702] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  425.936708] b43-phy0: Controller RESET (DMA error) ...
[  425.936742] b43-phy0 debug: Wireless interface stopped
[  425.936837] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  425.936905] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  425.938277] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  425.940463] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  425.942295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  425.944293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  426.090448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  426.092835] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  427.475466] b43-phy0 debug: Chip initialized
[  427.475623] b43-phy0 debug: 64-bit DMA initialized
[  427.484220] Registered led device: b43-phy0::tx
[  427.484242] Registered led device: b43-phy0::rx
[  427.484366] Registered led device: b43-phy0::radio
[  427.484626] b43-phy0 debug: Wireless interface started
[  427.484629] b43-phy0: 
[  427.484655] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  427.484660] b43-phy0: Controller RESET (DMA error) ...
[  427.484663] Controller restarted
[  427.484697] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  427.484702] b43-phy0: Controller RESET (DMA error) ...
[  427.484737] b43-phy0 debug: Wireless interface stopped
[  427.484833] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  427.485056] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  427.487273] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  427.489295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  427.491294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  427.493293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  427.639448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  427.641833] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  429.024462] b43-phy0 debug: Chip initialized
[  429.024619] b43-phy0 debug: 64-bit DMA initialized
[  429.033223] Registered led device: b43-phy0::tx
[  429.033244] Registered led device: b43-phy0::rx
[  429.033368] Registered led device: b43-phy0::radio
[  429.033627] b43-phy0 debug: Wireless interface started
[  429.033691] b43-phy0 debug: Wireless interface stopped
[  429.033787] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  429.033855] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  429.035277] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  429.037298] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  429.039295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  429.041294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  429.187461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  429.189853] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  430.572480] b43-phy0 debug: Chip initialized
[  430.572647] b43-phy0 debug: 64-bit DMA initialized
[  430.581230] Registered led device: b43-phy0::tx
[  430.581319] Registered led device: b43-phy0::rx
[  430.581533] Registered led device: b43-phy0::radio
[  430.581604] b43-phy0 debug: Wireless interface started
[  430.581703] b43-phy0 debug: Wireless interface stopped
[  430.581802] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  430.582027] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  430.584266] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  430.586296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  430.588294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  430.590293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  430.736461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  430.738849] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  432.121466] b43-phy0 debug: Chip initialized
[  432.121623] b43-phy0 debug: 64-bit DMA initialized
[  432.130222] Registered led device: b43-phy0::tx
[  432.130245] Registered led device: b43-phy0::rx
[  432.130368] Registered led device: b43-phy0::radio
[  432.130628] b43-phy0 debug: Wireless interface started
[  432.130631] __ratelimit: 8 callbacks suppressed
[  432.130661] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  432.130665] b43-phy0: Controller RESET (DMA error) ...
[  432.130669] b43-phy0: Controller restarted
[  432.130702] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  432.130708] b43-phy0: Controller RESET (DMA error) ...
[  432.130742] b43-phy0 debug: Wireless interface stopped
[  432.130836] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  432.130905] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  432.132276] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  432.134497] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  432.136294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  432.138293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  432.284448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  432.286837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  433.669478] b43-phy0 debug: Chip initialized
[  433.669642] b43-phy0 debug: 64-bit DMA initialized
[  433.678227] Registered led device: b43-phy0::tx
[  433.678260] Registered led device: b43-phy0::rx
[  433.678375] Registered led device: b43-phy0::radio
[  433.678636] b43-phy0 debug: Wireless interface started
[  433.678639] b43-phy0: 
[  433.678668] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  433.678673] b43-phy0: Controller RESET (DMA error) ...
[  433.678676] Controller restarted
[  433.678710] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  433.678715] b43-phy0: Controller RESET (DMA error) ...
[  433.678750] b43-phy0 debug: Wireless interface stopped
[  433.678847] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  433.679069] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  433.681275] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  433.683296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  433.685294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  433.687294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  433.833448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  433.835836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  435.218479] b43-phy0 debug: Chip initialized
[  435.218632] b43-phy0 debug: 64-bit DMA initialized
[  435.227216] Registered led device: b43-phy0::tx
[  435.227238] Registered led device: b43-phy0::rx
[  435.227361] Registered led device: b43-phy0::radio
[  435.227620] b43-phy0 debug: Wireless interface started
[  435.227684] b43-phy0 debug: Wireless interface stopped
[  435.227781] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  435.228003] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  435.229275] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  435.231496] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  435.233298] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  435.235294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  435.381460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  435.383846] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  436.766466] b43-phy0 debug: Chip initialized
[  436.766622] b43-phy0 debug: 64-bit DMA initialized
[  436.775222] Registered led device: b43-phy0::tx
[  436.775244] Registered led device: b43-phy0::rx
[  436.775368] Registered led device: b43-phy0::radio
[  436.775627] b43-phy0 debug: Wireless interface started
[  436.775726] b43-phy0 debug: Wireless interface stopped
[  436.775816] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  436.775849] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  436.777266] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  436.779288] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  436.781294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  436.783293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  436.930448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  436.932836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  438.315478] b43-phy0 debug: Chip initialized
[  438.315644] b43-phy0 debug: 64-bit DMA initialized
[  438.324226] Registered led device: b43-phy0::tx
[  438.324249] Registered led device: b43-phy0::rx
[  438.324375] Registered led device: b43-phy0::radio
[  438.324635] b43-phy0 debug: Wireless interface started
[  438.324638] __ratelimit: 8 callbacks suppressed
[  438.324669] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  438.324674] b43-phy0: Controller RESET (DMA error) ...
[  438.324677] b43-phy0: Controller restarted
[  438.324710] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  438.324716] b43-phy0: Controller RESET (DMA error) ...
[  438.324750] b43-phy0 debug: Wireless interface stopped
[  438.324847] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  438.325070] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  438.327267] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  438.329284] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  438.331294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  438.333293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  438.479460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  438.481850] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  439.864475] b43-phy0 debug: Chip initialized
[  439.864630] b43-phy0 debug: 64-bit DMA initialized
[  439.873219] Registered led device: b43-phy0::tx
[  439.873241] Registered led device: b43-phy0::rx
[  439.873365] Registered led device: b43-phy0::radio
[  439.873624] b43-phy0 debug: Wireless interface started
[  439.873627] b43-phy0: 
[  439.873654] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  439.873658] b43-phy0: Controller RESET (DMA error) ...
[  439.873661] Controller restarted
[  439.873695] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  439.873700] b43-phy0: Controller RESET (DMA error) ...
[  439.873735] b43-phy0 debug: Wireless interface stopped
[  439.873831] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  439.873901] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  439.875277] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  439.877496] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  439.879294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  439.881293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  440.027468] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  440.029857] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  441.412466] b43-phy0 debug: Chip initialized
[  441.412636] b43-phy0 debug: 64-bit DMA initialized
[  441.421231] Registered led device: b43-phy0::tx
[  441.421322] Registered led device: b43-phy0::rx
[  441.421536] Registered led device: b43-phy0::radio
[  441.421607] b43-phy0 debug: Wireless interface started
[  441.421670] b43-phy0 debug: Wireless interface stopped
[  441.421767] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  441.421990] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  441.423274] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  441.425499] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  441.427295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  441.429294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  441.575448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  441.577837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  442.960478] b43-phy0 debug: Chip initialized
[  442.960632] b43-phy0 debug: 64-bit DMA initialized
[  442.969218] Registered led device: b43-phy0::tx
[  442.969240] Registered led device: b43-phy0::rx
[  442.969364] Registered led device: b43-phy0::radio
[  442.969625] b43-phy0 debug: Wireless interface started
[  442.969721] b43-phy0 debug: Wireless interface stopped
[  442.969809] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  442.969842] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  442.971275] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  442.973285] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  442.975294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  442.977293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  443.123448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  443.125832] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  444.508478] b43-phy0 debug: Chip initialized
[  444.508642] b43-phy0 debug: 64-bit DMA initialized
[  444.517040] Registered led device: b43-phy0::tx
[  444.517063] Registered led device: b43-phy0::rx
[  444.517085] Registered led device: b43-phy0::radio
[  444.517156] b43-phy0 debug: Wireless interface started
[  444.517160] __ratelimit: 8 callbacks suppressed
[  444.517190] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  444.517194] b43-phy0: Controller RESET (DMA error) ...
[  444.517198] b43-phy0: Controller restarted
[  444.517232] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  444.517237] b43-phy0: Controller RESET (DMA error) ...
[  444.517284] b43-phy0 debug: Wireless interface stopped
[  444.517969] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  444.518192] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  444.520285] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  444.522297] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  444.524297] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  444.526293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  444.672447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  444.674837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  446.057465] b43-phy0 debug: Chip initialized
[  446.057620] b43-phy0 debug: 64-bit DMA initialized
[  446.066216] Registered led device: b43-phy0::tx
[  446.066238] Registered led device: b43-phy0::rx
[  446.066362] Registered led device: b43-phy0::radio
[  446.066621] b43-phy0 debug: Wireless interface started
[  446.066624] b43-phy0: 
[  446.066651] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  446.066655] b43-phy0: Controller RESET (DMA error) ...
[  446.066658] Controller restarted
[  446.066692] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  446.066698] b43-phy0: Controller RESET (DMA error) ...
[  446.066732] b43-phy0 debug: Wireless interface stopped
[  446.066827] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  446.066895] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  446.068276] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  446.070297] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  446.072295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  446.074293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  446.220447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  446.222832] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  447.605478] b43-phy0 debug: Chip initialized
[  447.605636] b43-phy0 debug: 64-bit DMA initialized
[  447.614220] Registered led device: b43-phy0::tx
[  447.614240] Registered led device: b43-phy0::rx
[  447.614362] Registered led device: b43-phy0::radio
[  447.614621] b43-phy0 debug: Wireless interface started
[  447.614685] b43-phy0 debug: Wireless interface stopped
[  447.614780] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  447.614847] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  447.616275] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  447.618470] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  447.620294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  447.622293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  447.768462] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  447.770847] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  449.153464] b43-phy0 debug: Chip initialized
[  449.153619] b43-phy0 debug: 64-bit DMA initialized
[  449.162215] Registered led device: b43-phy0::tx
[  449.162237] Registered led device: b43-phy0::rx
[  449.162359] Registered led device: b43-phy0::radio
[  449.162618] b43-phy0 debug: Wireless interface started
[  449.162714] b43-phy0 debug: Wireless interface stopped
[  449.162803] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  449.162834] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  449.164265] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  449.166471] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  449.168298] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  449.170293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  449.316449] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  449.318839] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  450.701476] b43-phy0 debug: Chip initialized
[  450.701631] b43-phy0 debug: 64-bit DMA initialized
[  450.710215] Registered led device: b43-phy0::tx
[  450.710237] Registered led device: b43-phy0::rx
[  450.710360] Registered led device: b43-phy0::radio
[  450.710619] b43-phy0 debug: Wireless interface started
[  450.710622] __ratelimit: 8 callbacks suppressed
[  450.710652] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  450.710656] b43-phy0: Controller RESET (DMA error) ...
[  450.710659] b43-phy0: Controller restarted
[  450.710693] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  450.710699] b43-phy0: Controller RESET (DMA error) ...
[  450.710733] b43-phy0 debug: Wireless interface stopped
[  450.710824] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  450.710892] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  450.712276] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  450.714498] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  450.716293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  450.718293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  450.864461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  450.866849] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  452.432273] b43-phy0 debug: Chip initialized
[  452.432448] b43-phy0 debug: 64-bit DMA initialized
[  452.442906] Registered led device: b43-phy0::tx
[  452.442929] Registered led device: b43-phy0::rx
[  452.442953] Registered led device: b43-phy0::radio
[  452.443043] b43-phy0 debug: Wireless interface started
[  452.443046] b43-phy0: 
[  452.443079] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  452.443083] b43-phy0: Controller RESET (DMA error) ...
[  452.443085] Controller restarted
[  452.443119] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  452.443123] b43-phy0: Controller RESET (DMA error) ...
[  452.443158] b43-phy0 debug: Wireless interface stopped
[  452.443256] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  452.443480] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  452.446018] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  452.448049] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  452.450054] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  452.452039] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  452.600454] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  452.602842] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  453.985455] b43-phy0 debug: Chip initialized
[  453.985615] b43-phy0 debug: 64-bit DMA initialized
[  453.994538] Registered led device: b43-phy0::tx
[  453.995380] Registered led device: b43-phy0::rx
[  453.995597] Registered led device: b43-phy0::radio
[  453.995668] b43-phy0 debug: Wireless interface started
[  453.995705] b43-phy0 debug: Wireless interface stopped
[  453.995810] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  453.996047] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  453.998017] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  454.000230] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  454.002220] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  454.004214] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  454.151441] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  454.153826] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  455.536470] b43-phy0 debug: Chip initialized
[  455.536627] b43-phy0 debug: 64-bit DMA initialized
[  455.545511] Registered led device: b43-phy0::tx
[  455.545906] Registered led device: b43-phy0::rx
[  455.546749] Registered led device: b43-phy0::radio
[  455.547023] b43-phy0 debug: Wireless interface started
[  455.547397] b43-phy0 debug: Wireless interface stopped
[  455.547509] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  455.547735] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  455.549017] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  455.551221] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  455.553221] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  455.555212] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  455.702454] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  455.704840] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  457.087455] b43-phy0 debug: Chip initialized
[  457.087612] b43-phy0 debug: 64-bit DMA initialized
[  457.096515] Registered led device: b43-phy0::tx
[  457.096997] Registered led device: b43-phy0::rx
[  457.097482] Registered led device: b43-phy0::radio
[  457.097971] b43-phy0 debug: Wireless interface started
[  457.097975] __ratelimit: 6 callbacks suppressed
[  457.097977] b43-phy0: Controller restarted
[  457.098004] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  457.098010] b43-phy0: Controller RESET (DMA error) ...
[  457.098043] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  457.098050] b43-phy0: Controller RESET (DMA error) ...
[  457.098622] b43-phy0 debug: Wireless interface stopped
[  457.098741] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  457.098966] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  457.101250] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  457.103218] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  457.105212] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  457.107213] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  457.253439] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  457.255828] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  458.639470] b43-phy0 debug: Chip initialized
[  458.639622] b43-phy0 debug: 64-bit DMA initialized
[  458.648219] Registered led device: b43-phy0::tx
[  458.648279] Registered led device: b43-phy0::rx
[  458.648301] Registered led device: b43-phy0::radio
[  458.648371] b43-phy0 debug: Wireless interface started
[  458.648373] b43-phy0: Controller restarted
[  458.648401] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  458.648405] b43-phy0: Controller RESET (DMA error) ...
[  458.648445] b43-phy0 debug: Wireless interface stopped
[  458.648530] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  458.648560] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  458.650015] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  458.652018] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  458.654221] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  458.656220] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  458.803452] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  458.805838] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  460.188458] b43-phy0 debug: Chip initialized
[  460.188610] b43-phy0 debug: 64-bit DMA initialized
[  460.197520] Registered led device: b43-phy0::tx
[  460.197913] Registered led device: b43-phy0::rx
[  460.198755] Registered led device: b43-phy0::radio
[  460.199028] b43-phy0 debug: Wireless interface started
[  460.199031] b43-phy0: Controller restarted
[  460.199076] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  460.199460] b43-phy0 debug: Wireless interface stopped
[  460.199568] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  460.199794] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  460.201016] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  460.203219] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  460.205222] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  460.207212] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  460.354454] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  460.356844] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  461.739469] b43-phy0 debug: Chip initialized
[  461.739620] b43-phy0 debug: 64-bit DMA initialized
[  461.748505] Registered led device: b43-phy0::tx
[  461.748901] Registered led device: b43-phy0::rx
[  461.749741] Registered led device: b43-phy0::radio
[  461.750013] b43-phy0 debug: Wireless interface started
[  461.750221] b43-phy0 debug: Wireless interface stopped
[  461.750332] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  461.750555] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  461.752018] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  461.754224] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  461.756216] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  461.758214] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  461.905440] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  461.907825] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  463.290459] b43-phy0 debug: Chip initialized
[  463.290626] b43-phy0 debug: 64-bit DMA initialized
[  463.299598] Registered led device: b43-phy0::tx
[  463.300440] Registered led device: b43-phy0::rx
[  463.300655] Registered led device: b43-phy0::radio
[  463.300726] b43-phy0 debug: Wireless interface started
[  463.300729] __ratelimit: 8 callbacks suppressed
[  463.300731] b43-phy0: Controller restarted
[  463.300774] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  463.300780] b43-phy0: Controller RESET (DMA error) ...
[  463.300818] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  463.300823] b43-phy0: Controller RESET (DMA error) ...
[  463.300859] b43-phy0 debug: Wireless interface stopped
[  463.300972] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  463.301199] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  463.303270] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  463.305292] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  463.307293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  463.309293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  463.455460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  463.457848] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  464.840476] b43-phy0 debug: Chip initialized
[  464.840632] b43-phy0 debug: 64-bit DMA initialized
[  464.849216] Registered led device: b43-phy0::tx
[  464.849239] Registered led device: b43-phy0::rx
[  464.849776] Registered led device: b43-phy0::radio
[  464.850041] b43-phy0 debug: Wireless interface started
[  464.850044] b43-phy0: Controller restarted
[  464.850077] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  464.850082] b43-phy0: Controller RESET (DMA error) ...
[  464.850116] b43-phy0 debug: Wireless interface stopped
[  464.850212] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  464.850448] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  464.853508] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  464.855306] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  464.857297] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  464.859296] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  465.005456] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  465.007841] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  466.390477] b43-phy0 debug: Chip initialized
[  466.390632] b43-phy0 debug: 64-bit DMA initialized
[  466.399514] Registered led device: b43-phy0::tx
[  466.399992] Registered led device: b43-phy0::rx
[  466.400489] Registered led device: b43-phy0::radio
[  466.400749] b43-phy0 debug: Wireless interface started
[  466.400752] b43-phy0: Controller restarted
[  466.400785] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  466.400822] b43-phy0 debug: Wireless interface stopped
[  466.402349] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  466.402573] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  466.404293] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  466.406293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  466.408293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  466.410293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  466.556447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  466.558836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  467.941475] b43-phy0 debug: Chip initialized
[  467.941628] b43-phy0 debug: 64-bit DMA initialized
[  467.950503] Registered led device: b43-phy0::tx
[  467.950979] Registered led device: b43-phy0::rx
[  467.951831] Registered led device: b43-phy0::radio
[  467.952093] b43-phy0 debug: Wireless interface started
[  467.952188] b43-phy0 debug: Wireless interface stopped
[  467.952620] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  467.952844] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  467.954272] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  467.956295] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  467.958294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  467.960294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  468.106450] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  468.108837] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  469.491465] b43-phy0 debug: Chip initialized
[  469.491618] b43-phy0 debug: 64-bit DMA initialized
[  469.500520] Registered led device: b43-phy0::tx
[  469.500997] Registered led device: b43-phy0::rx
[  469.501501] Registered led device: b43-phy0::radio
[  469.501761] b43-phy0 debug: Wireless interface started
[  469.501765] __ratelimit: 6 callbacks suppressed
[  469.501767] b43-phy0: Controller restarted
[  469.501800] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  469.501806] b43-phy0: Controller RESET (DMA error) ...
[  469.501841] b43-phy0 debug: Wireless interface stopped
[  469.503436] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  469.503662] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  469.505290] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  469.507293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  469.509295] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  469.511295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  469.657447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  469.659836] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  471.042476] b43-phy0 debug: Chip initialized
[  471.042630] b43-phy0 debug: 64-bit DMA initialized
[  471.051516] Registered led device: b43-phy0::tx
[  471.051995] Registered led device: b43-phy0::rx
[  471.052497] Registered led device: b43-phy0::radio
[  471.052757] b43-phy0 debug: Wireless interface started
[  471.052760] b43-phy0: Controller restarted
[  471.052793] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  471.052799] b43-phy0: Controller RESET (DMA error) ...
[  471.052829] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  471.052833] b43-phy0: Controller RESET (DMA error) ...
[  471.052868] b43-phy0 debug: Wireless interface stopped
[  471.054298] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  471.054525] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  471.056302] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  471.058293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  471.060296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  471.062295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  471.208446] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  471.210830] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  472.593477] b43-phy0 debug: Chip initialized
[  472.593634] b43-phy0 debug: 64-bit DMA initialized
[  472.602530] Registered led device: b43-phy0::tx
[  472.603011] Registered led device: b43-phy0::rx
[  472.603483] Registered led device: b43-phy0::radio
[  472.603976] b43-phy0 debug: Wireless interface started
[  472.603979] b43-phy0: Controller restarted
[  472.604020] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  472.604084] b43-phy0 debug: Wireless interface stopped
[  472.604844] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  472.605073] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  472.607283] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  472.609294] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  472.611294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  472.613293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  472.759460] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  472.761846] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  474.144466] b43-phy0 debug: Chip initialized
[  474.144632] b43-phy0 debug: 64-bit DMA initialized
[  474.153040] Registered led device: b43-phy0::tx
[  474.153063] Registered led device: b43-phy0::rx
[  474.153085] Registered led device: b43-phy0::radio
[  474.153156] b43-phy0 debug: Wireless interface started
[  474.153262] b43-phy0 debug: Wireless interface stopped
[  474.154888] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  474.155121] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  474.157278] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  474.159281] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  474.161289] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  474.163303] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  474.309279] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  474.311671] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  475.694465] b43-phy0 debug: Chip initialized
[  475.694628] b43-phy0 debug: 64-bit DMA initialized
[  475.703543] Registered led device: b43-phy0::tx
[  475.704384] Registered led device: b43-phy0::rx
[  475.704599] Registered led device: b43-phy0::radio
[  475.704668] b43-phy0 debug: Wireless interface started
[  475.704671] __ratelimit: 8 callbacks suppressed
[  475.704673] b43-phy0: Controller restarted
[  475.704711] b43-phy0 debug: Wireless interface stopped
[  475.704815] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  475.705041] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  475.706273] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  475.708297] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  475.710296] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  475.712297] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  475.858447] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  475.860834] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  477.243477] b43-phy0 debug: Chip initialized
[  477.243631] b43-phy0 debug: 64-bit DMA initialized
[  477.252518] Registered led device: b43-phy0::tx
[  477.253000] Registered led device: b43-phy0::rx
[  477.253496] Registered led device: b43-phy0::radio
[  477.253988] b43-phy0 debug: Wireless interface started
[  477.253992] b43-phy0: Controller restarted
[  477.254031] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  477.254037] b43-phy0: Controller RESET (DMA error) ...
[  477.254075] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  477.254080] b43-phy0: Controller RESET (DMA error) ...
[  477.254121] b43-phy0 debug: Wireless interface stopped
[  477.254966] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  477.255194] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  477.257295] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  477.259293] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  477.261294] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  477.263293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  477.409462] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  477.411851] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  478.794475] b43-phy0 debug: Chip initialized
[  478.794627] b43-phy0 debug: 64-bit DMA initialized
[  478.803212] Registered led device: b43-phy0::tx
[  478.803233] Registered led device: b43-phy0::rx
[  478.803775] Registered led device: b43-phy0::radio
[  478.804041] b43-phy0 debug: Wireless interface started
[  478.804043] b43-phy0: Controller restarted
[  478.804071] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  478.804077] b43-phy0: Controller RESET (DMA error) ...
[  478.804109] b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000
[  478.805130] b43-phy0 debug: Wireless interface stopped
[  478.805495] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  478.805719] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  478.807284] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  478.809302] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  478.811298] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  478.813293] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  478.960461] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  478.962851] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  480.345480] b43-phy0 debug: Chip initialized
[  480.345646] b43-phy0 debug: 64-bit DMA initialized
[  480.354590] Registered led device: b43-phy0::tx
[  480.355450] Registered led device: b43-phy0::rx
[  480.355665] Registered led device: b43-phy0::radio
[  480.355736] b43-phy0 debug: Wireless interface started
[  480.355857] b43-phy0 debug: Wireless interface stopped
[  480.355966] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  480.356193] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  480.357268] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  480.359284] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  480.361300] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  480.363295] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  480.509448] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[  480.511834] b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
[  481.894474] b43-phy0 debug: Chip initialized
[  481.894634] b43-phy0 debug: 64-bit DMA initialized
[  481.903521] Registered led device: b43-phy0::tx
[  481.904015] Registered led device: b43-phy0::rx
[  481.904490] Registered led device: b43-phy0::radio
[  481.904983] b43-phy0 debug: Wireless interface started
[  481.905105] b43-phy0 debug: Wireless interface stopped
[  481.905777] b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%, Average tries 0.00
[  481.906004] b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  481.907498] b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  481.909296] b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  481.911293] b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00
[  481.913294] b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 = 0.0%, Average tries 0.00

^ permalink raw reply

* Re: b43 dma error
From: Gábor Stefanik @ 2009-09-08 14:08 UTC (permalink / raw)
  To: Dave Young; +Cc: mb, linville, linux-wireless, bcm43xx-dev
In-Reply-To: <20090908134732.GA1936@darkstar>

Do you have the threaded-IRQ patches applied? Also, what card is this?
(BCM4312?) Try upgrading your firmare (use v478 or the new v5xx one).

^ permalink raw reply

* Re: Atheros Linux wireless drivers home page - and two new driver projects
From: Bob Copeland @ 2009-09-08 14:11 UTC (permalink / raw)
  To: Denis Kirjanov
  Cc: michael, Xavier Bestel, devel, b_yogesh_snowy, Dan Williams,
	Stefan Lippers-Hollmann, Len Widra, linux-wireless, linux-kernel,
	Stephen Chen, Jouni Malinen, Nick Kossifidis, Paul Fertser,
	Harald Welte, Witold Sowa, Michael Renzmann, Werner Almesberger
In-Reply-To: <a872555b0909072350qf105990q3efb99a8bbb2d0bc@mail.gmail.com>

On Tue, Sep 08, 2009 at 10:50:46AM +0400, Denis Kirjanov wrote:
> Good time of day.
> Do I need to use wireless-testing tree ?

For what goal?  Generally speaking, no you do
not need to use wireless-testing, unless you wish
to test or contribute, in which cases the answer
is "yes."

-Bob


^ permalink raw reply

* Re: b43 dma error
From: Michael Buesch @ 2009-09-08 14:38 UTC (permalink / raw)
  To: Dave Young; +Cc: linville, netrolller.3d, linux-wireless, bcm43xx-dev
In-Reply-To: <20090908134732.GA1936@darkstar>

On Tuesday 08 September 2009 15:47:32 Dave Young wrote:
> I tested wireless-testing b43 driver, but got "Fatal DMA error"
> then the controller keep restarting...
> 
> Please tell what I can provide or test, Thanks.

Is this a regression? If so, please bisect.

-- 
Greetings, Michael.

^ permalink raw reply

* Re: iwlagn: order 2 page allocation failures
From: John W. Linville @ 2009-09-08 14:17 UTC (permalink / raw)
  To: Pekka Enberg
  Cc: Mel Gorman, Frans Pop, linux-kernel, linux-wireless,
	ipw3945-devel, Andrew Morton, cl
In-Reply-To: <84144f020909080411n4e010308qa153039bee1b8336@mail.gmail.com>

On Tue, Sep 08, 2009 at 02:11:35PM +0300, Pekka Enberg wrote:
> On Tue, Sep 8, 2009 at 1:54 PM, Mel Gorman<mel@csn.ul.ie> wrote:
> > My feeling is also that a number of these page allocation failures have
> > been related to wireless drivers. Is that accurate? If so, have there
> > been changes made to the wireless stack in this cycle that would have
> > increased the order of pages allocated?
> 
> That's my general feeling as well. We have linux-wireless CC'd so
> maybe this rings a bell for them.

AFAIK, this is only the second separate report.  The other related
to ipw2200, which actually shares no code with the iwlagn driver and
is not based on the mac80211 stack.

Hth!

John
-- 
John W. Linville		Someday the world will need a hero, and you
linville@tuxdriver.com			might be all we have.  Be ready.

^ permalink raw reply

* Re: iwlagn: order 2 page allocation failures
From: Larry Finger @ 2009-09-08 14:59 UTC (permalink / raw)
  To: John W. Linville
  Cc: Pekka Enberg, Mel Gorman, Frans Pop, linux-kernel, linux-wireless,
	ipw3945-devel, Andrew Morton, cl
In-Reply-To: <20090908141701.GB2617@tuxdriver.com>

John W. Linville wrote:
> On Tue, Sep 08, 2009 at 02:11:35PM +0300, Pekka Enberg wrote:
>> On Tue, Sep 8, 2009 at 1:54 PM, Mel Gorman<mel@csn.ul.ie> wrote:
>>> My feeling is also that a number of these page allocation failures have
>>> been related to wireless drivers. Is that accurate? If so, have there
>>> been changes made to the wireless stack in this cycle that would have
>>> increased the order of pages allocated?
>> That's my general feeling as well. We have linux-wireless CC'd so
>> maybe this rings a bell for them.
> 
> AFAIK, this is only the second separate report.  The other related
> to ipw2200, which actually shares no code with the iwlagn driver and
> is not based on the mac80211 stack.

A previous issue concerned the interaction between wireless and SLUB
debugging that caused O(0) allocations to get bumped to O(1), but that
was not relevant to this case either. I'm not aware of any other page
allocation problems with wireless.

Larry

^ permalink raw reply

* Re: b43 dma error
From: Larry Finger @ 2009-09-08 14:54 UTC (permalink / raw)
  To: Michael Buesch
  Cc: Dave Young, linville, netrolller.3d, linux-wireless, bcm43xx-dev
In-Reply-To: <200909081638.36897.mb@bu3sch.de>

Michael Buesch wrote:
> On Tuesday 08 September 2009 15:47:32 Dave Young wrote:
>> I tested wireless-testing b43 driver, but got "Fatal DMA error"
>> then the controller keep restarting...
>>
>> Please tell what I can provide or test, Thanks.
> 
> Is this a regression? If so, please bisect.

It is something specific to his system as I don't see anything like
this. In addition, there are some users on the openSUSE forums that
have implemented the latest compat-wireless and switched away from
Broadcom wl to b43 on their LP PHY devices. So far, no complaints from
them.

Please reboot so that we see the ssb output as well. Use the command

dmesg | egrep "ssb|b43"

That way we will be able to see exactly what kind of device you have
and what revisions are in it. AFAIK, the testing to date has been
limited to Rev 1 PHYs and Rev 2 radios.

Larry



^ permalink raw reply

* Re: [gNewSense-users] firmware development Fwd: convocatoria (pagada) a desarrollo
From: Luis R. Rodriguez @ 2009-09-08 16:06 UTC (permalink / raw)
  To: Quiliro Ordóñez; +Cc: linux-wireless
In-Reply-To: <606e87f00909060900n20469a68k4e2540b7d99334b4@mail.gmail.com>

On Sun, Sep 6, 2009 at 9:00 AM, Quiliro Ordóñez<quiliro@gmail.com> wrote:
> Dear folks.
>
> I have like to have libre (free as in freedom) firmware for rt2561
> wireless chipset. And forward this email for your consideration and
> quote.

I think we can poke ralink, but anyway in the meantime be aware that
if you want a wireless device for which there are open upstream
drivers and either open firmware or no firmware requirement you can
refer to:

These devices require no firmware:

http://wireless.kernel.org/en/users/Drivers/ath5k
http://wireless.kernel.org/en/users/Drivers/ath9k

This driver has open firmware available:

http://wireless.kernel.org/en/users/Drivers/ar9170
http://wireless.kernel.org/en/users/Drivers/ar9170.fw

  Luis

^ permalink raw reply

* Re: [PATCH] cfg80211: Fix build error on i386 for net/wireless/scan.o
From: Luis R. Rodriguez @ 2009-09-08 16:09 UTC (permalink / raw)
  To: Larry Finger; +Cc: John W Linville, Johannes Berg, linux-wireless
In-Reply-To: <4aa3f838.ef04Hi2n3Fg54rE9%Larry.Finger@lwfinger.net>

On Sun, Sep 6, 2009 at 10:58 AM, Larry Finger<Larry.Finger@lwfinger.net> wrote:
> With i386 architecture, building the kernel v2.6.31-rc8-34797-g4910edb
> fails with the following error:
>
>  CC [M]  net/wireless/scan.o
> net/wireless/scan.c: In function ‘cfg80211_inform_bss’:
> net/wireless/scan.c:499: error: implicit declaration of function ‘kmemleak_ignore’
> make[2]: *** [net/wireless/scan.o] Error 1
>
> On x86_64, the build succeeds. Fix by including the appropriate header.
>
> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>

I've asked John to revert the use of kmemleak_ignore() here for
several reasons so this patch will not be needed.

  Luis

^ permalink raw reply

* Re: Stop using tasklets for bottom halves
From: Stephen Hemminger @ 2009-09-08 16:11 UTC (permalink / raw)
  To: rostedt
  Cc: Luis R. Rodriguez, Ingo Molnar, Michael Buesch, John W. Linville,
	linux-wireless, linux-kernel, netdev, Matt Smith, Kevin Hayes,
	Bob Copeland, Jouni Malinen, Ivan Seskar, ic.felix
In-Reply-To: <1252376254.21261.2052.camel@gandalf.stny.rr.com>

On Mon, 07 Sep 2009 22:17:34 -0400
Steven Rostedt <rostedt@goodmis.org> wrote:

> On Mon, 2009-09-07 at 17:14 -0700, Stephen Hemminger wrote:
> > On Mon, 7 Sep 2009 15:58:50 -0700
> > "Luis R. Rodriguez" <mcgrof@gmail.com> wrote:
> > 
> > > A while ago I had read about an effort to consider removing tasklets
> > > [1] or at least trying to not use them. I'm unaware of the progress in
> > > this respect but since reading that article have always tried to
> > > evaluate whether or not we need tasklets on wireless drivers. I have
> > > also wondered whether work in irq context in other parts of the kernel
> > > can be moved to process context, a curious example being timers. I'll
> > > personally be trying to using only process context on bottom halves on
> > > future drivers but I figured it may be a good time to ask how serious
> > > was avoiding tasklets or using wrappers in the future to avoid irq
> > > context is or is it advised. Do we have a general agreement this is a
> > > good step forward to take? Has anyone made tests or changes on a
> > > specific driver from irq context to process context and proven there
> > > are no significant advantages of using irq context where you would
> > > have expected it?
> > > 
> > > Wireless in particular should IMHO not require taskets for anything
> > > time sensitive that I can think about except perhaps changing channels
> > > quickly and to do that appropriately also process pending RX frames
> > > prior to a switch. It remains to be seen experimentally whether or not
> > > using a workqueue for RX processing would affect the time to switch
> > > channels negatively but I doubt it would be significant. I hope to
> > > test that with ath9k_htc.
> > > 
> > > What about gigabit or 10 Gigabit Ethernet drivers ? Do they face any
> > > challenges which would yet need to be proven would not face issues
> > > when processing bottom halves in process context?
> > > 
> > > [1] http://lwn.net/Articles/239633/
> > > 
> > >   Luis
> > > --
> > > To unsubscribe from this list: send the line "unsubscribe netdev" in
> > > the body of a message to majordomo@vger.kernel.org
> > > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > 
> > Why not use NAPI, which is soft irq? Almost all 1G and 10G drivers
> > use NAPI.
> > 
> > Process context is too slow.
> 
> Well, I'm hoping to prove the opposite. I'm working on some stuff that I
> plan to present at Linux Plumbers. I've been too distracted by other
> things, but hopefully I'll have some good numbers to present by then.
> 


That's great, does it keep the good properties of NAPI (irq disabling
and throttling?)



-- 

^ permalink raw reply

* Re: Stop using tasklets for bottom halves
From: Stephen Hemminger @ 2009-09-08 16:12 UTC (permalink / raw)
  To: rostedt
  Cc: Luis R. Rodriguez, Ingo Molnar, Michael Buesch, John W. Linville,
	linux-wireless, linux-kernel, netdev, Matt Smith, Kevin Hayes,
	Bob Copeland, Jouni Malinen, Ivan Seskar, ic.felix
In-Reply-To: <1252376254.21261.2052.camel@gandalf.stny.rr.com>

On Mon, 07 Sep 2009 22:17:34 -0400
Steven Rostedt <rostedt@goodmis.org> wrote:

> On Mon, 2009-09-07 at 17:14 -0700, Stephen Hemminger wrote:
> > On Mon, 7 Sep 2009 15:58:50 -0700
> > "Luis R. Rodriguez" <mcgrof@gmail.com> wrote:
> > 
> > > A while ago I had read about an effort to consider removing tasklets
> > > [1] or at least trying to not use them. I'm unaware of the progress in
> > > this respect but since reading that article have always tried to
> > > evaluate whether or not we need tasklets on wireless drivers. I have
> > > also wondered whether work in irq context in other parts of the kernel
> > > can be moved to process context, a curious example being timers. I'll
> > > personally be trying to using only process context on bottom halves on
> > > future drivers but I figured it may be a good time to ask how serious
> > > was avoiding tasklets or using wrappers in the future to avoid irq
> > > context is or is it advised. Do we have a general agreement this is a
> > > good step forward to take? Has anyone made tests or changes on a
> > > specific driver from irq context to process context and proven there
> > > are no significant advantages of using irq context where you would
> > > have expected it?
> > > 
> > > Wireless in particular should IMHO not require taskets for anything
> > > time sensitive that I can think about except perhaps changing channels
> > > quickly and to do that appropriately also process pending RX frames
> > > prior to a switch. It remains to be seen experimentally whether or not
> > > using a workqueue for RX processing would affect the time to switch
> > > channels negatively but I doubt it would be significant. I hope to
> > > test that with ath9k_htc.
> > > 
> > > What about gigabit or 10 Gigabit Ethernet drivers ? Do they face any
> > > challenges which would yet need to be proven would not face issues
> > > when processing bottom halves in process context?
> > > 
> > > [1] http://lwn.net/Articles/239633/
> > > 
> > >   Luis
> > > --
> > > To unsubscribe from this list: send the line "unsubscribe netdev" in
> > > the body of a message to majordomo@vger.kernel.org
> > > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > 
> > Why not use NAPI, which is soft irq? Almost all 1G and 10G drivers
> > use NAPI.
> > 
> > Process context is too slow.
> 
> Well, I'm hoping to prove the opposite. I'm working on some stuff that I
> plan to present at Linux Plumbers. I've been too distracted by other
> things, but hopefully I'll have some good numbers to present by then.
> 
> -- Steve
> 
> 

A good performance test is changing the behaviour of loopback
device and running lmbench.  This checks overhead without the specter
of real hardware.

-- 

^ permalink raw reply

* Re: Stop using tasklets for bottom halves
From: Steven Rostedt @ 2009-09-08 16:40 UTC (permalink / raw)
  To: Stephen Hemminger
  Cc: Luis R. Rodriguez, Ingo Molnar, Michael Buesch, John W. Linville,
	linux-wireless, linux-kernel, netdev, Matt Smith, Kevin Hayes,
	Bob Copeland, Jouni Malinen, Ivan Seskar, ic.felix
In-Reply-To: <20090908091143.1e613963@nehalam>

On Tue, 2009-09-08 at 09:11 -0700, Stephen Hemminger wrote:

> > > Process context is too slow.
> > 
> > Well, I'm hoping to prove the opposite. I'm working on some stuff that I
> > plan to present at Linux Plumbers. I've been too distracted by other
> > things, but hopefully I'll have some good numbers to present by then.
> > 
> 
> 
> That's great, does it keep the good properties of NAPI (irq disabling
> and throttling?)

Not exactly sure what you mean by throttling, but I'm assuming it will.

As for irqs disabling, I'm trying to avoid doing that. Note, the device
will have its interrupts disabled, but not all other devices will.

-- Steve



^ permalink raw reply

* Re: Stop using tasklets for bottom halves
From: Stephen Hemminger @ 2009-09-08 17:01 UTC (permalink / raw)
  To: rostedt
  Cc: Luis R. Rodriguez, Ingo Molnar, Michael Buesch, John W. Linville,
	linux-wireless, linux-kernel, netdev, Matt Smith, Kevin Hayes,
	Bob Copeland, Jouni Malinen, Ivan Seskar, ic.felix
In-Reply-To: <1252428023.15626.30.camel@gandalf.stny.rr.com>

On Tue, 08 Sep 2009 12:40:23 -0400
Steven Rostedt <rostedt@goodmis.org> wrote:

> On Tue, 2009-09-08 at 09:11 -0700, Stephen Hemminger wrote:
> 
> > > > Process context is too slow.
> > > 
> > > Well, I'm hoping to prove the opposite. I'm working on some stuff that I
> > > plan to present at Linux Plumbers. I've been too distracted by other
> > > things, but hopefully I'll have some good numbers to present by then.
> > > 
> > 
> > 
> > That's great, does it keep the good properties of NAPI (irq disabling
> > and throttling?)
> 
> Not exactly sure what you mean by throttling, but I'm assuming it will.
> 
> As for irqs disabling, I'm trying to avoid doing that. Note, the device
> will have its interrupts disabled, but not all other devices will.
> 
> -- Steve
> 
> 

The way NAPI works is that in irq routine, the device disables interrupts
then schedules processing packets, when processing is done irq's are re-enabled.
This means that if machine is being flooded, irq's stay off, and the packets
get discarded (because device hardware ring is full), rather than in software
(because software receive queue is full).


-- 

^ permalink raw reply

* Re: driver_nl80211 broken again
From: Johannes Berg @ 2009-09-08 15:29 UTC (permalink / raw)
  To: Maxim Levitsky; +Cc: linux-wireless, Jouni Malinen
In-Reply-To: <1252116503.2398.26.camel@maxim-laptop>

[-- Attachment #1: Type: text/plain, Size: 2682 bytes --]

On Sat, 2009-09-05 at 05:08 +0300, Maxim Levitsky wrote:

> 1 - when connecting again to the access point (same or another), 
> wpa_supplicant does the following:
> 
> deassoc
> auth
> assoc
> 
> So it assumes that deassoc command disconnects completely, but it not
> longer true.
> Yet, I have tried to make its dissassoc function do both, but it failed.
> I used following patch:
> 
> 
> diff --git a/wpa_supplicant/wpa_supplicant.c b/wpa_supplicant/wpa_supplicant.c
> index c68dd82..50afeeb 100644
> --- a/wpa_supplicant/wpa_supplicant.c
> +++ b/wpa_supplicant/wpa_supplicant.c
> @@ -1278,8 +1278,10 @@ void wpa_supplicant_disassociate(struct wpa_supplicant *wpa_s,
>         if (!is_zero_ether_addr(wpa_s->bssid)) {
>                 if (wpa_s->drv_flags & WPA_DRIVER_FLAGS_USER_SPACE_MLME)
>                         ieee80211_sta_disassociate(wpa_s, reason_code);
> -               else
> +               else {
>                         wpa_drv_disassociate(wpa_s, wpa_s->bssid, reason_code);
> +                       wpa_drv_deauthenticate(wpa_s, wpa_s->bssid, reason_code);
> +               }
>                 addr = wpa_s->bssid;
>         }
>         wpa_clear_keys(wpa_s, addr);

Right, this is a known problem. I still think it should be handled in
wpa_s, but I'm not sure whether that patch should have worked or not.

> EAPOL: startWhen --> 0
> EAPOL: disable timer tick
> wpa_driver_nl80211_disassociate
> wpa_driver_nl80211_deauthenticate
> nl80211: MLME command failed: ret=-67 (Link has been severed)

Ok so it was called, but got -ENOLINK? That's rather odd. But I suspect
that it had already internally cleared the BSSID, so that it was asking
to deauth from 00:...:00 -- could you check that?

> 2 - independent of the above, the ieee80211_set_disassoc
> doesn't work right if deauth==false.
> 
> 
> If it is, then a work item is added to station work thread, and it is
> never removed:
> 
> 	} else {
> 		struct ieee80211_mgd_work *wk = ifmgd->old_associate_work;
> 
> 		wk->state = IEEE80211_MGD_STATE_IDLE;
> 		list_add(&wk->list, &ifmgd->work_list);
> 	}
> 
> 
> iee80211_sta_work just ignores the IEEE80211_MGD_STATE_IDLE, thus it
> work item remains forever.
> 
> This breaks scanning, since __ieee80211_start_scan will refuses to run
> until, ifmgd->work_list is empty.

That's intentional, that work item represents the authentication state
we still have -- the required cleanup should be done by cfg80211 or
wpa_supplicant.

Can you try to figure out what the parameters are that
wpa_drv_deauthenticate() is sending to the kernel, and why it's getting
-ENOLINK?

johannes


[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 801 bytes --]

^ permalink raw reply

* [PATCH] genetlink: fix netns vs. netlink table locking
From: Johannes Berg @ 2009-09-08 15:59 UTC (permalink / raw)
  To: netdev; +Cc: linux-wireless

Since my commits introducing netns awareness into
genetlink we can get this problem:

BUG: scheduling while atomic: modprobe/1178/0x00000002
2 locks held by modprobe/1178:
 #0:  (genl_mutex){+.+.+.}, at: [<ffffffff8135ee1a>] genl_register_mc_grou
 #1:  (rcu_read_lock){.+.+..}, at: [<ffffffff8135eeb5>] genl_register_mc_g
Pid: 1178, comm: modprobe Not tainted 2.6.31-rc8-wl-34789-g95cb731-dirty #
Call Trace:
 [<ffffffff8103e285>] __schedule_bug+0x85/0x90
 [<ffffffff81403138>] schedule+0x108/0x588
 [<ffffffff8135b131>] netlink_table_grab+0xa1/0xf0
 [<ffffffff8135c3a7>] netlink_change_ngroups+0x47/0x100
 [<ffffffff8135ef0f>] genl_register_mc_group+0x12f/0x290

because I overlooked that netlink_table_grab() will
schedule, thinking it was just the rwlock. However,
in the contention case, that isn't actually true.

Fix this by letting the code grab the netlink table
lock first and then the RCU for netns protection.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
---
 include/linux/netlink.h  |    4 +++
 net/netlink/af_netlink.c |   51 ++++++++++++++++++++++++++---------------------
 net/netlink/genetlink.c  |    5 +++-
 3 files changed, 37 insertions(+), 23 deletions(-)

--- wireless-testing.orig/include/linux/netlink.h	2009-09-08 17:49:54.000000000 +0200
+++ wireless-testing/include/linux/netlink.h	2009-09-08 17:50:29.000000000 +0200
@@ -176,12 +176,16 @@ struct netlink_skb_parms
 #define NETLINK_CREDS(skb)	(&NETLINK_CB((skb)).creds)
 
 
+extern void netlink_table_grab(void);
+extern void netlink_table_ungrab(void);
+
 extern struct sock *netlink_kernel_create(struct net *net,
 					  int unit,unsigned int groups,
 					  void (*input)(struct sk_buff *skb),
 					  struct mutex *cb_mutex,
 					  struct module *module);
 extern void netlink_kernel_release(struct sock *sk);
+extern int __netlink_change_ngroups(struct sock *sk, unsigned int groups);
 extern int netlink_change_ngroups(struct sock *sk, unsigned int groups);
 extern void netlink_clear_multicast_users(struct sock *sk, unsigned int group);
 extern void netlink_ack(struct sk_buff *in_skb, struct nlmsghdr *nlh, int err);
--- wireless-testing.orig/net/netlink/af_netlink.c	2009-09-08 17:37:57.000000000 +0200
+++ wireless-testing/net/netlink/af_netlink.c	2009-09-08 17:52:45.000000000 +0200
@@ -177,9 +177,11 @@ static void netlink_sock_destruct(struct
  * this, _but_ remember, it adds useless work on UP machines.
  */
 
-static void netlink_table_grab(void)
+void netlink_table_grab(void)
 	__acquires(nl_table_lock)
 {
+	might_sleep();
+
 	write_lock_irq(&nl_table_lock);
 
 	if (atomic_read(&nl_table_users)) {
@@ -200,7 +202,7 @@ static void netlink_table_grab(void)
 	}
 }
 
-static void netlink_table_ungrab(void)
+void netlink_table_ungrab(void)
 	__releases(nl_table_lock)
 {
 	write_unlock_irq(&nl_table_lock);
@@ -1549,37 +1551,21 @@ static void netlink_free_old_listeners(s
 	kfree(lrh->ptr);
 }
 
-/**
- * netlink_change_ngroups - change number of multicast groups
- *
- * This changes the number of multicast groups that are available
- * on a certain netlink family. Note that it is not possible to
- * change the number of groups to below 32. Also note that it does
- * not implicitly call netlink_clear_multicast_users() when the
- * number of groups is reduced.
- *
- * @sk: The kernel netlink socket, as returned by netlink_kernel_create().
- * @groups: The new number of groups.
- */
-int netlink_change_ngroups(struct sock *sk, unsigned int groups)
+int __netlink_change_ngroups(struct sock *sk, unsigned int groups)
 {
 	unsigned long *listeners, *old = NULL;
 	struct listeners_rcu_head *old_rcu_head;
 	struct netlink_table *tbl = &nl_table[sk->sk_protocol];
-	int err = 0;
 
 	if (groups < 32)
 		groups = 32;
 
-	netlink_table_grab();
 	if (NLGRPSZ(tbl->groups) < NLGRPSZ(groups)) {
 		listeners = kzalloc(NLGRPSZ(groups) +
 				    sizeof(struct listeners_rcu_head),
 				    GFP_ATOMIC);
-		if (!listeners) {
-			err = -ENOMEM;
-			goto out_ungrab;
-		}
+		if (!listeners)
+			return -ENOMEM;
 		old = tbl->listeners;
 		memcpy(listeners, old, NLGRPSZ(tbl->groups));
 		rcu_assign_pointer(tbl->listeners, listeners);
@@ -1597,8 +1583,29 @@ int netlink_change_ngroups(struct sock *
 	}
 	tbl->groups = groups;
 
- out_ungrab:
+	return 0;
+}
+
+/**
+ * netlink_change_ngroups - change number of multicast groups
+ *
+ * This changes the number of multicast groups that are available
+ * on a certain netlink family. Note that it is not possible to
+ * change the number of groups to below 32. Also note that it does
+ * not implicitly call netlink_clear_multicast_users() when the
+ * number of groups is reduced.
+ *
+ * @sk: The kernel netlink socket, as returned by netlink_kernel_create().
+ * @groups: The new number of groups.
+ */
+int netlink_change_ngroups(struct sock *sk, unsigned int groups)
+{
+	int err;
+
+	netlink_table_grab();
+	err = __netlink_change_ngroups(sk, groups);
 	netlink_table_ungrab();
+
 	return err;
 }
 EXPORT_SYMBOL(netlink_change_ngroups);
--- wireless-testing.orig/net/netlink/genetlink.c	2009-09-08 17:50:38.000000000 +0200
+++ wireless-testing/net/netlink/genetlink.c	2009-09-08 17:58:50.000000000 +0200
@@ -176,9 +176,10 @@ int genl_register_mc_group(struct genl_f
 	if (family->netnsok) {
 		struct net *net;
 
+		netlink_table_grab();
 		rcu_read_lock();
 		for_each_net_rcu(net) {
-			err = netlink_change_ngroups(net->genl_sock,
+			err = __netlink_change_ngroups(net->genl_sock,
 					mc_groups_longs * BITS_PER_LONG);
 			if (err) {
 				/*
@@ -188,10 +189,12 @@ int genl_register_mc_group(struct genl_f
 				 * increased on some sockets which is ok.
 				 */
 				rcu_read_unlock();
+				netlink_table_ungrab();
 				goto out;
 			}
 		}
 		rcu_read_unlock();
+		netlink_table_ungrab();
 	} else {
 		err = netlink_change_ngroups(init_net.genl_sock,
 					     mc_groups_longs * BITS_PER_LONG);



^ permalink raw reply

* Re: Stop using tasklets for bottom halves
From: Steven Rostedt @ 2009-09-08 17:27 UTC (permalink / raw)
  To: Stephen Hemminger
  Cc: Luis R. Rodriguez, Ingo Molnar, Michael Buesch, John W. Linville,
	linux-wireless, linux-kernel, netdev, Matt Smith, Kevin Hayes,
	Bob Copeland, Jouni Malinen, Ivan Seskar, ic.felix,
	Thomas Gleixner
In-Reply-To: <20090908100144.6e06872b@nehalam>

[ added Thomas Gleixner to Cc]

On Tue, 2009-09-08 at 10:01 -0700, Stephen Hemminger wrote:
> On Tue, 08 Sep 2009 12:40:23 -0400
> Steven Rostedt <rostedt@goodmis.org> wrote:
> 
> > On Tue, 2009-09-08 at 09:11 -0700, Stephen Hemminger wrote:
> > 
> > > > > Process context is too slow.
> > > > 
> > > > Well, I'm hoping to prove the opposite. I'm working on some stuff that I
> > > > plan to present at Linux Plumbers. I've been too distracted by other
> > > > things, but hopefully I'll have some good numbers to present by then.
> > > > 
> > > 
> > > 
> > > That's great, does it keep the good properties of NAPI (irq disabling
> > > and throttling?)
> > 
> > Not exactly sure what you mean by throttling, but I'm assuming it will.
> > 
> > As for irqs disabling, I'm trying to avoid doing that. Note, the device
> > will have its interrupts disabled, but not all other devices will.
> > 
> > -- Steve
> > 
> > 
> 
> The way NAPI works is that in irq routine, the device disables interrupts
> then schedules processing packets, when processing is done irq's are re-enabled.
> This means that if machine is being flooded, irq's stay off, and the packets
> get discarded (because device hardware ring is full), rather than in software
> (because software receive queue is full).

That sounds exactly like what threaded IRQs will do. When an interrupt
comes in, the device driver will disable the device interrupts, and then
the device irq thread handler is awoken.

The device irq handler will handle all the packets. If new packets come
in, and the hardware ring buffer is full, those packets will be dropped.
When the irq handler thread is done processing all pending packets, it
will re-enable the device's interrupts and go to sleep.

Yeah, looking at the NAPI code, it does seem to follow what threaded
interrupts do.

-- Steve



^ permalink raw reply

* [PATCH] ssb: Implement SDIO host bus support
From: Michael Buesch @ 2009-09-08 17:30 UTC (permalink / raw)
  To: John W. Linville; +Cc: Broadcom Wireless, linux-wireless, Albert Herranz

From: Albert Herranz <albert_herranz@yahoo.es>

Add support for communicating with a Sonics Silicon Backplane through a
SDIO interface, as found in the Nintendo Wii WLAN daughter card.

The Nintendo Wii WLAN card includes a custom Broadcom 4318 chip with
a SDIO host interface.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>

---
 drivers/ssb/Kconfig       |   14 +
 drivers/ssb/Makefile      |    1 +
 drivers/ssb/main.c        |   58 +++++-
 drivers/ssb/scan.c        |   11 +
 drivers/ssb/sdio.c        |  611 +++++++++++++++++++++++++++++++++++++++++++++
 drivers/ssb/ssb_private.h |   40 +++
 include/linux/ssb/ssb.h   |   32 +++
 7 files changed, 766 insertions(+), 1 deletions(-)
 create mode 100644 drivers/ssb/sdio.c

Index: wireless-testing/drivers/ssb/Kconfig
===================================================================
--- wireless-testing.orig/drivers/ssb/Kconfig	2009-09-08 19:13:49.000000000 +0200
+++ wireless-testing/drivers/ssb/Kconfig	2009-09-08 19:14:13.000000000 +0200
@@ -66,6 +66,20 @@ config SSB_PCMCIAHOST
 
 	  If unsure, say N
 
+config SSB_SDIOHOST_POSSIBLE
+	bool
+	depends on SSB && (MMC = y || MMC = SSB)
+	default y
+
+config SSB_SDIOHOST
+	bool "Support for SSB on SDIO-bus host"
+	depends on SSB_SDIOHOST_POSSIBLE
+	help
+	  Support for a Sonics Silicon Backplane on top
+	  of a SDIO device.
+
+	  If unsure, say N
+
 config SSB_SILENT
 	bool "No SSB kernel messages"
 	depends on SSB && EMBEDDED
Index: wireless-testing/drivers/ssb/Makefile
===================================================================
--- wireless-testing.orig/drivers/ssb/Makefile	2009-09-08 19:13:49.000000000 +0200
+++ wireless-testing/drivers/ssb/Makefile	2009-09-08 19:14:13.000000000 +0200
@@ -6,6 +6,7 @@ ssb-$(CONFIG_SSB_SPROM)			+= sprom.o
 # host support
 ssb-$(CONFIG_SSB_PCIHOST)		+= pci.o pcihost_wrapper.o
 ssb-$(CONFIG_SSB_PCMCIAHOST)		+= pcmcia.o
+ssb-$(CONFIG_SSB_SDIOHOST)		+= sdio.o
 
 # built-in drivers
 ssb-y					+= driver_chipcommon.o
Index: wireless-testing/drivers/ssb/main.c
===================================================================
--- wireless-testing.orig/drivers/ssb/main.c	2009-09-08 19:13:49.000000000 +0200
+++ wireless-testing/drivers/ssb/main.c	2009-09-08 19:14:13.000000000 +0200
@@ -17,6 +17,7 @@
 #include <linux/ssb/ssb_driver_gige.h>
 #include <linux/dma-mapping.h>
 #include <linux/pci.h>
+#include <linux/mmc/sdio_func.h>
 
 #include <pcmcia/cs_types.h>
 #include <pcmcia/cs.h>
@@ -88,6 +89,25 @@ found:
 }
 #endif /* CONFIG_SSB_PCMCIAHOST */
 
+#ifdef CONFIG_SSB_SDIOHOST
+struct ssb_bus *ssb_sdio_func_to_bus(struct sdio_func *func)
+{
+	struct ssb_bus *bus;
+
+	ssb_buses_lock();
+	list_for_each_entry(bus, &buses, list) {
+		if (bus->bustype == SSB_BUSTYPE_SDIO &&
+		    bus->host_sdio == func)
+			goto found;
+	}
+	bus = NULL;
+found:
+	ssb_buses_unlock();
+
+	return bus;
+}
+#endif /* CONFIG_SSB_SDIOHOST */
+
 int ssb_for_each_bus_call(unsigned long data,
 			  int (*func)(struct ssb_bus *bus, unsigned long data))
 {
@@ -469,6 +489,12 @@ static int ssb_devices_register(struct s
 			dev->parent = &bus->host_pcmcia->dev;
 #endif
 			break;
+		case SSB_BUSTYPE_SDIO:
+#ifdef CONFIG_SSB_SDIO
+			sdev->irq = bus->host_sdio->dev.irq;
+			dev->parent = &bus->host_sdio->dev;
+#endif
+			break;
 		case SSB_BUSTYPE_SSB:
 			dev->dma_mask = &dev->coherent_dma_mask;
 			break;
@@ -724,12 +750,18 @@ static int ssb_bus_register(struct ssb_b
 	err = ssb_pci_xtal(bus, SSB_GPIO_XTAL | SSB_GPIO_PLL, 1);
 	if (err)
 		goto out;
+
+	/* Init SDIO-host device (if any), before the scan */
+	err = ssb_sdio_init(bus);
+	if (err)
+		goto err_disable_xtal;
+
 	ssb_buses_lock();
 	bus->busnumber = next_busnumber;
 	/* Scan for devices (cores) */
 	err = ssb_bus_scan(bus, baseaddr);
 	if (err)
-		goto err_disable_xtal;
+		goto err_sdio_exit;
 
 	/* Init PCI-host device (if any) */
 	err = ssb_pci_init(bus);
@@ -776,6 +808,8 @@ err_pci_exit:
 	ssb_pci_exit(bus);
 err_unmap:
 	ssb_iounmap(bus);
+err_sdio_exit:
+	ssb_sdio_exit(bus);
 err_disable_xtal:
 	ssb_buses_unlock();
 	ssb_pci_xtal(bus, SSB_GPIO_XTAL | SSB_GPIO_PLL, 0);
@@ -825,6 +859,28 @@ int ssb_bus_pcmciabus_register(struct ss
 EXPORT_SYMBOL(ssb_bus_pcmciabus_register);
 #endif /* CONFIG_SSB_PCMCIAHOST */
 
+#ifdef CONFIG_SSB_SDIOHOST
+int ssb_bus_sdiobus_register(struct ssb_bus *bus, struct sdio_func *func,
+			     unsigned int quirks)
+{
+	int err;
+
+	bus->bustype = SSB_BUSTYPE_SDIO;
+	bus->host_sdio = func;
+	bus->ops = &ssb_sdio_ops;
+	bus->quirks = quirks;
+
+	err = ssb_bus_register(bus, ssb_sdio_get_invariants, ~0);
+	if (!err) {
+		ssb_printk(KERN_INFO PFX "Sonics Silicon Backplane found on "
+			   "SDIO device %s\n", sdio_func_id(func));
+	}
+
+	return err;
+}
+EXPORT_SYMBOL(ssb_bus_sdiobus_register);
+#endif /* CONFIG_SSB_PCMCIAHOST */
+
 int ssb_bus_ssbbus_register(struct ssb_bus *bus,
 			    unsigned long baseaddr,
 			    ssb_invariants_func_t get_invariants)
Index: wireless-testing/drivers/ssb/scan.c
===================================================================
--- wireless-testing.orig/drivers/ssb/scan.c	2009-09-08 19:13:49.000000000 +0200
+++ wireless-testing/drivers/ssb/scan.c	2009-09-08 19:14:13.000000000 +0200
@@ -175,6 +175,9 @@ static u32 scan_read32(struct ssb_bus *b
 		} else
 			ssb_pcmcia_switch_segment(bus, 0);
 		break;
+	case SSB_BUSTYPE_SDIO:
+		offset += current_coreidx * SSB_CORE_SIZE;
+		return ssb_sdio_scan_read32(bus, offset);
 	}
 	return readl(bus->mmio + offset);
 }
@@ -188,6 +191,8 @@ static int scan_switchcore(struct ssb_bu
 		return ssb_pci_switch_coreidx(bus, coreidx);
 	case SSB_BUSTYPE_PCMCIA:
 		return ssb_pcmcia_switch_coreidx(bus, coreidx);
+	case SSB_BUSTYPE_SDIO:
+		return ssb_sdio_scan_switch_coreidx(bus, coreidx);
 	}
 	return 0;
 }
@@ -206,6 +211,8 @@ void ssb_iounmap(struct ssb_bus *bus)
 		SSB_BUG_ON(1); /* Can't reach this code. */
 #endif
 		break;
+	case SSB_BUSTYPE_SDIO:
+		break;
 	}
 	bus->mmio = NULL;
 	bus->mapped_device = NULL;
@@ -230,6 +237,10 @@ static void __iomem *ssb_ioremap(struct 
 		SSB_BUG_ON(1); /* Can't reach this code. */
 #endif
 		break;
+	case SSB_BUSTYPE_SDIO:
+		/* Nothing to ioremap in the SDIO case, just fake it */
+		mmio = (void __iomem *)baseaddr;
+		break;
 	}
 
 	return mmio;
Index: wireless-testing/drivers/ssb/sdio.c
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ wireless-testing/drivers/ssb/sdio.c	2009-09-08 19:14:13.000000000 +0200
@@ -0,0 +1,610 @@
+/*
+ * Sonics Silicon Backplane
+ * SDIO-Hostbus related functions
+ *
+ * Copyright 2009 Albert Herranz <albert_herranz@yahoo.es>
+ *
+ * Based on drivers/ssb/pcmcia.c
+ * Copyright 2006 Johannes Berg <johannes@sipsolutions.net>
+ * Copyright 2007-2008 Michael Buesch <mb@bu3sch.de>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ *
+ */
+
+#include <linux/ssb/ssb.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/etherdevice.h>
+#include <linux/mmc/sdio_func.h>
+
+#include "ssb_private.h"
+
+/* Define the following to 1 to enable a printk on each coreswitch. */
+#define SSB_VERBOSE_SDIOCORESWITCH_DEBUG		1
+
+
+/* Hardware invariants CIS tuples */
+#define SSB_SDIO_CIS			0x80
+#define  SSB_SDIO_CIS_SROMREV		0x00
+#define  SSB_SDIO_CIS_ID		0x01
+#define  SSB_SDIO_CIS_BOARDREV		0x02
+#define  SSB_SDIO_CIS_PA		0x03
+#define   SSB_SDIO_CIS_PA_PA0B0_LO	0
+#define   SSB_SDIO_CIS_PA_PA0B0_HI	1
+#define   SSB_SDIO_CIS_PA_PA0B1_LO	2
+#define   SSB_SDIO_CIS_PA_PA0B1_HI	3
+#define   SSB_SDIO_CIS_PA_PA0B2_LO	4
+#define   SSB_SDIO_CIS_PA_PA0B2_HI	5
+#define   SSB_SDIO_CIS_PA_ITSSI		6
+#define   SSB_SDIO_CIS_PA_MAXPOW	7
+#define  SSB_SDIO_CIS_OEMNAME		0x04
+#define  SSB_SDIO_CIS_CCODE		0x05
+#define  SSB_SDIO_CIS_ANTENNA		0x06
+#define  SSB_SDIO_CIS_ANTGAIN		0x07
+#define  SSB_SDIO_CIS_BFLAGS		0x08
+#define  SSB_SDIO_CIS_LEDS		0x09
+
+#define CISTPL_FUNCE_LAN_NODE_ID        0x04	/* same as in PCMCIA */
+
+
+/*
+ * Function 1 miscellaneous registers.
+ *
+ * Definitions match src/include/sbsdio.h from the
+ * Android Open Source Project
+ * http://android.git.kernel.org/?p=platform/system/wlan/broadcom.git
+ *
+ */
+#define SBSDIO_FUNC1_SBADDRLOW	0x1000a	/* SB Address window Low (b15) */
+#define SBSDIO_FUNC1_SBADDRMID	0x1000b	/* SB Address window Mid (b23-b16) */
+#define SBSDIO_FUNC1_SBADDRHIGH	0x1000c	/* SB Address window High (b24-b31) */
+
+/* valid bits in SBSDIO_FUNC1_SBADDRxxx regs */
+#define SBSDIO_SBADDRLOW_MASK	0x80	/* Valid address bits in SBADDRLOW */
+#define SBSDIO_SBADDRMID_MASK	0xff	/* Valid address bits in SBADDRMID */
+#define SBSDIO_SBADDRHIGH_MASK	0xff	/* Valid address bits in SBADDRHIGH */
+
+#define SBSDIO_SB_OFT_ADDR_MASK	0x7FFF	/* sb offset addr is <= 15 bits, 32k */
+
+/* REVISIT: this flag doesn't seem to matter */
+#define SBSDIO_SB_ACCESS_2_4B_FLAG	0x8000	/* forces 32-bit SB access */
+
+
+/*
+ * Address map within the SDIO function address space (128K).
+ *
+ *   Start   End     Description
+ *   ------- ------- ------------------------------------------
+ *   0x00000 0x0ffff selected backplane address window (64K)
+ *   0x10000 0x1ffff backplane control registers (max 64K)
+ *
+ * The current address window is configured by writing to registers
+ * SBADDRLOW, SBADDRMID and SBADDRHIGH.
+ *
+ * In order to access the contents of a 32-bit Silicon Backplane address
+ * the backplane address window must be first loaded with the highest
+ * 16 bits of the target address. Then, an access must be done to the
+ * SDIO function address space using the lower 15 bits of the address.
+ * Bit 15 of the address must be set when doing 32 bit accesses.
+ *
+ * 10987654321098765432109876543210
+ * WWWWWWWWWWWWWWWWW                 SB Address Window
+ *                 OOOOOOOOOOOOOOOO  Offset within SB Address Window
+ *                 a                 32-bit access flag
+ */
+
+
+/*
+ * SSB I/O via SDIO.
+ *
+ * NOTE: SDIO address @addr is 17 bits long (SDIO address space is 128K).
+ */
+
+static inline struct device *ssb_sdio_dev(struct ssb_bus *bus)
+{
+	return &bus->host_sdio->dev;
+}
+
+/* host claimed */
+static int ssb_sdio_writeb(struct ssb_bus *bus, unsigned int addr, u8 val)
+{
+	int error = 0;
+
+	sdio_writeb(bus->host_sdio, val, addr, &error);
+	if (unlikely(error)) {
+		dev_dbg(ssb_sdio_dev(bus), "%08X <- %02x, error %d\n",
+			addr, val, error);
+	}
+
+	return error;
+}
+
+#if 0
+static u8 ssb_sdio_readb(struct ssb_bus *bus, unsigned int addr)
+{
+	u8 val;
+	int error = 0;
+
+	val = sdio_readb(bus->host_sdio, addr, &error);
+	if (unlikely(error)) {
+		dev_dbg(ssb_sdio_dev(bus), "%08X -> %02x, error %d\n",
+			addr, val, error);
+	}
+
+	return val;
+}
+#endif
+
+/* host claimed */
+static int ssb_sdio_set_sbaddr_window(struct ssb_bus *bus, u32 address)
+{
+	int error;
+
+	error = ssb_sdio_writeb(bus, SBSDIO_FUNC1_SBADDRLOW,
+				(address >> 8) & SBSDIO_SBADDRLOW_MASK);
+	if (error)
+		goto out;
+	error = ssb_sdio_writeb(bus, SBSDIO_FUNC1_SBADDRMID,
+				(address >> 16) & SBSDIO_SBADDRMID_MASK);
+	if (error)
+		goto out;
+	error = ssb_sdio_writeb(bus, SBSDIO_FUNC1_SBADDRHIGH,
+				(address >> 24) & SBSDIO_SBADDRHIGH_MASK);
+	if (error)
+		goto out;
+	bus->sdio_sbaddr = address;
+out:
+	if (error) {
+		dev_dbg(ssb_sdio_dev(bus), "failed to set address window"
+			" to 0x%08x, error %d\n", address, error);
+	}
+
+	return error;
+}
+
+/* for enumeration use only */
+u32 ssb_sdio_scan_read32(struct ssb_bus *bus, u16 offset)
+{
+	u32 val;
+	int error;
+
+	sdio_claim_host(bus->host_sdio);
+	val = sdio_readl(bus->host_sdio, offset, &error);
+	sdio_release_host(bus->host_sdio);
+	if (unlikely(error)) {
+		dev_dbg(ssb_sdio_dev(bus), "%04X:%04X > %08x, error %d\n",
+			bus->sdio_sbaddr >> 16, offset, val, error);
+	}
+
+	return val;
+}
+
+/* for enumeration use only */
+int ssb_sdio_scan_switch_coreidx(struct ssb_bus *bus, u8 coreidx)
+{
+	u32 sbaddr;
+	int error;
+
+	sbaddr = (coreidx * SSB_CORE_SIZE) + SSB_ENUM_BASE;
+	sdio_claim_host(bus->host_sdio);
+	error = ssb_sdio_set_sbaddr_window(bus, sbaddr);
+	sdio_release_host(bus->host_sdio);
+	if (error) {
+		dev_err(ssb_sdio_dev(bus), "failed to switch to core %u,"
+			" error %d\n", coreidx, error);
+		goto out;
+	}
+out:
+	return error;
+}
+
+/* host must be already claimed */
+int ssb_sdio_switch_core(struct ssb_bus *bus, struct ssb_device *dev)
+{
+	u8 coreidx = dev->core_index;
+	u32 sbaddr;
+	int error = 0;
+
+	sbaddr = (coreidx * SSB_CORE_SIZE) + SSB_ENUM_BASE;
+	if (unlikely(bus->sdio_sbaddr != sbaddr)) {
+#if SSB_VERBOSE_SDIOCORESWITCH_DEBUG
+		dev_info(ssb_sdio_dev(bus),
+			   "switching to %s core, index %d\n",
+			   ssb_core_name(dev->id.coreid), coreidx);
+#endif
+		error = ssb_sdio_set_sbaddr_window(bus, sbaddr);
+		if (error) {
+			dev_dbg(ssb_sdio_dev(bus), "failed to switch to"
+				" core %u, error %d\n", coreidx, error);
+			goto out;
+		}
+		bus->mapped_device = dev;
+	}
+
+out:
+	return error;
+}
+
+static u8 ssb_sdio_read8(struct ssb_device *dev, u16 offset)
+{
+	struct ssb_bus *bus = dev->bus;
+	u8 val = 0xff;
+	int error = 0;
+
+	sdio_claim_host(bus->host_sdio);
+	if (unlikely(ssb_sdio_switch_core(bus, dev)))
+		goto out;
+	offset |= bus->sdio_sbaddr & 0xffff;
+	offset &= SBSDIO_SB_OFT_ADDR_MASK;
+	val = sdio_readb(bus->host_sdio, offset, &error);
+	if (error) {
+		dev_dbg(ssb_sdio_dev(bus), "%04X:%04X > %02x, error %d\n",
+			bus->sdio_sbaddr >> 16, offset, val, error);
+	}
+out:
+	sdio_release_host(bus->host_sdio);
+
+	return val;
+}
+
+static u16 ssb_sdio_read16(struct ssb_device *dev, u16 offset)
+{
+	struct ssb_bus *bus = dev->bus;
+	u16 val = 0xffff;
+	int error = 0;
+
+	sdio_claim_host(bus->host_sdio);
+	if (unlikely(ssb_sdio_switch_core(bus, dev)))
+		goto out;
+	offset |= bus->sdio_sbaddr & 0xffff;
+	offset &= SBSDIO_SB_OFT_ADDR_MASK;
+	val = sdio_readw(bus->host_sdio, offset, &error);
+	if (error) {
+		dev_dbg(ssb_sdio_dev(bus), "%04X:%04X > %04x, error %d\n",
+			bus->sdio_sbaddr >> 16, offset, val, error);
+	}
+out:
+	sdio_release_host(bus->host_sdio);
+
+	return val;
+}
+
+static u32 ssb_sdio_read32(struct ssb_device *dev, u16 offset)
+{
+	struct ssb_bus *bus = dev->bus;
+	u32 val = 0xffffffff;
+	int error = 0;
+
+	sdio_claim_host(bus->host_sdio);
+	if (unlikely(ssb_sdio_switch_core(bus, dev)))
+		goto out;
+	offset |= bus->sdio_sbaddr & 0xffff;
+	offset &= SBSDIO_SB_OFT_ADDR_MASK;
+	offset |= SBSDIO_SB_ACCESS_2_4B_FLAG;	/* 32 bit data access */
+	val = sdio_readl(bus->host_sdio, offset, &error);
+	if (error) {
+		dev_dbg(ssb_sdio_dev(bus), "%04X:%04X > %08x, error %d\n",
+			bus->sdio_sbaddr >> 16, offset, val, error);
+	}
+out:
+	sdio_release_host(bus->host_sdio);
+
+	return val;
+}
+
+#ifdef CONFIG_SSB_BLOCKIO
+static void ssb_sdio_block_read(struct ssb_device *dev, void *buffer,
+				  size_t count, u16 offset, u8 reg_width)
+{
+	size_t saved_count = count;
+	struct ssb_bus *bus = dev->bus;
+	int error = 0;
+
+	sdio_claim_host(bus->host_sdio);
+	if (unlikely(ssb_sdio_switch_core(bus, dev))) {
+		error = -EIO;
+		memset(buffer, 0xff, count);
+		goto err_out;
+	}
+	offset |= bus->sdio_sbaddr & 0xffff;
+	offset &= SBSDIO_SB_OFT_ADDR_MASK;
+
+	switch (reg_width) {
+	case sizeof(u8): {
+		error = sdio_readsb(bus->host_sdio, buffer, offset, count);
+		break;
+	}
+	case sizeof(u16): {
+		SSB_WARN_ON(count & 1);
+		error = sdio_readsb(bus->host_sdio, buffer, offset, count);
+		break;
+	}
+	case sizeof(u32): {
+		SSB_WARN_ON(count & 3);
+		offset |= SBSDIO_SB_ACCESS_2_4B_FLAG;	/* 32 bit data access */
+		error = sdio_readsb(bus->host_sdio, buffer, offset, count);
+		break;
+	}
+	default:
+		SSB_WARN_ON(1);
+	}
+	if (!error)
+		goto out;
+
+err_out:
+	dev_dbg(ssb_sdio_dev(bus), "%04X:%04X (width=%u, len=%u), error %d\n",
+		bus->sdio_sbaddr >> 16, offset, reg_width, saved_count, error);
+out:
+	sdio_release_host(bus->host_sdio);
+}
+#endif /* CONFIG_SSB_BLOCKIO */
+
+static void ssb_sdio_write8(struct ssb_device *dev, u16 offset, u8 val)
+{
+	struct ssb_bus *bus = dev->bus;
+	int error = 0;
+
+	sdio_claim_host(bus->host_sdio);
+	if (unlikely(ssb_sdio_switch_core(bus, dev)))
+		goto out;
+	offset |= bus->sdio_sbaddr & 0xffff;
+	offset &= SBSDIO_SB_OFT_ADDR_MASK;
+	sdio_writeb(bus->host_sdio, val, offset, &error);
+	if (error) {
+		dev_dbg(ssb_sdio_dev(bus), "%04X:%04X < %02x, error %d\n",
+			bus->sdio_sbaddr >> 16, offset, val, error);
+	}
+out:
+	sdio_release_host(bus->host_sdio);
+}
+
+static void ssb_sdio_write16(struct ssb_device *dev, u16 offset, u16 val)
+{
+	struct ssb_bus *bus = dev->bus;
+	int error = 0;
+
+	sdio_claim_host(bus->host_sdio);
+	if (unlikely(ssb_sdio_switch_core(bus, dev)))
+		goto out;
+	offset |= bus->sdio_sbaddr & 0xffff;
+	offset &= SBSDIO_SB_OFT_ADDR_MASK;
+	sdio_writew(bus->host_sdio, val, offset, &error);
+	if (error) {
+		dev_dbg(ssb_sdio_dev(bus), "%04X:%04X < %04x, error %d\n",
+			bus->sdio_sbaddr >> 16, offset, val, error);
+	}
+out:
+	sdio_release_host(bus->host_sdio);
+}
+
+static void ssb_sdio_write32(struct ssb_device *dev, u16 offset, u32 val)
+{
+	struct ssb_bus *bus = dev->bus;
+	int error = 0;
+
+	sdio_claim_host(bus->host_sdio);
+	if (unlikely(ssb_sdio_switch_core(bus, dev)))
+		goto out;
+	offset |= bus->sdio_sbaddr & 0xffff;
+	offset &= SBSDIO_SB_OFT_ADDR_MASK;
+	offset |= SBSDIO_SB_ACCESS_2_4B_FLAG;	/* 32 bit data access */
+	sdio_writel(bus->host_sdio, val, offset, &error);
+	if (error) {
+		dev_dbg(ssb_sdio_dev(bus), "%04X:%04X < %08x, error %d\n",
+			bus->sdio_sbaddr >> 16, offset, val, error);
+	}
+	if (bus->quirks & SSB_QUIRK_SDIO_READ_AFTER_WRITE32)
+		sdio_readl(bus->host_sdio, 0, &error);
+out:
+	sdio_release_host(bus->host_sdio);
+}
+
+#ifdef CONFIG_SSB_BLOCKIO
+static void ssb_sdio_block_write(struct ssb_device *dev, const void *buffer,
+				   size_t count, u16 offset, u8 reg_width)
+{
+	size_t saved_count = count;
+	struct ssb_bus *bus = dev->bus;
+	int error = 0;
+
+	sdio_claim_host(bus->host_sdio);
+	if (unlikely(ssb_sdio_switch_core(bus, dev))) {
+		error = -EIO;
+		memset((void *)buffer, 0xff, count);
+		goto err_out;
+	}
+	offset |= bus->sdio_sbaddr & 0xffff;
+	offset &= SBSDIO_SB_OFT_ADDR_MASK;
+
+	switch (reg_width) {
+	case sizeof(u8):
+		error = sdio_writesb(bus->host_sdio, offset,
+				     (void *)buffer, count);
+		break;
+	case sizeof(u16):
+		SSB_WARN_ON(count & 1);
+		error = sdio_writesb(bus->host_sdio, offset,
+				     (void *)buffer, count);
+		break;
+	case sizeof(u32):
+		SSB_WARN_ON(count & 3);
+		offset |= SBSDIO_SB_ACCESS_2_4B_FLAG;	/* 32 bit data access */
+		error = sdio_writesb(bus->host_sdio, offset,
+				     (void *)buffer, count);
+		break;
+	default:
+		SSB_WARN_ON(1);
+	}
+	if (!error)
+		goto out;
+
+err_out:
+	dev_dbg(ssb_sdio_dev(bus), "%04X:%04X (width=%u, len=%u), error %d\n",
+		bus->sdio_sbaddr >> 16, offset, reg_width, saved_count, error);
+out:
+	sdio_release_host(bus->host_sdio);
+}
+
+#endif /* CONFIG_SSB_BLOCKIO */
+
+/* Not "static", as it's used in main.c */
+const struct ssb_bus_ops ssb_sdio_ops = {
+	.read8		= ssb_sdio_read8,
+	.read16		= ssb_sdio_read16,
+	.read32		= ssb_sdio_read32,
+	.write8		= ssb_sdio_write8,
+	.write16	= ssb_sdio_write16,
+	.write32	= ssb_sdio_write32,
+#ifdef CONFIG_SSB_BLOCKIO
+	.block_read	= ssb_sdio_block_read,
+	.block_write	= ssb_sdio_block_write,
+#endif
+};
+
+#define GOTO_ERROR_ON(condition, description) do {	\
+	if (unlikely(condition)) {			\
+		error_description = description;	\
+		goto error;				\
+	}						\
+  } while (0)
+
+int ssb_sdio_get_invariants(struct ssb_bus *bus,
+			    struct ssb_init_invariants *iv)
+{
+	struct ssb_sprom *sprom = &iv->sprom;
+	struct ssb_boardinfo *bi = &iv->boardinfo;
+	const char *error_description = "none";
+	struct sdio_func_tuple *tuple;
+	void *mac;
+
+	memset(sprom, 0xFF, sizeof(*sprom));
+	sprom->boardflags_lo = 0;
+	sprom->boardflags_hi = 0;
+
+	tuple = bus->host_sdio->tuples;
+	while (tuple) {
+		switch (tuple->code) {
+		case 0x22: /* extended function */
+			switch (tuple->data[0]) {
+			case CISTPL_FUNCE_LAN_NODE_ID:
+				GOTO_ERROR_ON((tuple->size != 7) &&
+					      (tuple->data[1] != 6),
+					      "mac tpl size");
+				/* fetch the MAC address. */
+				mac = tuple->data + 2;
+				memcpy(sprom->il0mac, mac, ETH_ALEN);
+				memcpy(sprom->et1mac, mac, ETH_ALEN);
+				break;
+			default:
+				break;
+			}
+			break;
+		case 0x80: /* vendor specific tuple */
+			switch (tuple->data[0]) {
+			case SSB_SDIO_CIS_SROMREV:
+				GOTO_ERROR_ON(tuple->size != 2,
+					      "sromrev tpl size");
+				sprom->revision = tuple->data[1];
+				break;
+			case SSB_SDIO_CIS_ID:
+				GOTO_ERROR_ON((tuple->size != 5) &&
+					      (tuple->size != 7),
+					      "id tpl size");
+				bi->vendor = tuple->data[1] |
+					     (tuple->data[2]<<8);
+				break;
+			case SSB_SDIO_CIS_BOARDREV:
+				GOTO_ERROR_ON(tuple->size != 2,
+					      "boardrev tpl size");
+				sprom->board_rev = tuple->data[1];
+				break;
+			case SSB_SDIO_CIS_PA:
+				GOTO_ERROR_ON((tuple->size != 9) &&
+					      (tuple->size != 10),
+					      "pa tpl size");
+				sprom->pa0b0 = tuple->data[1] |
+					 ((u16)tuple->data[2] << 8);
+				sprom->pa0b1 = tuple->data[3] |
+					 ((u16)tuple->data[4] << 8);
+				sprom->pa0b2 = tuple->data[5] |
+					 ((u16)tuple->data[6] << 8);
+				sprom->itssi_a = tuple->data[7];
+				sprom->itssi_bg = tuple->data[7];
+				sprom->maxpwr_a = tuple->data[8];
+				sprom->maxpwr_bg = tuple->data[8];
+				break;
+			case SSB_SDIO_CIS_OEMNAME:
+				/* Not present */
+				break;
+			case SSB_SDIO_CIS_CCODE:
+				GOTO_ERROR_ON(tuple->size != 2,
+					      "ccode tpl size");
+				sprom->country_code = tuple->data[1];
+				break;
+			case SSB_SDIO_CIS_ANTENNA:
+				GOTO_ERROR_ON(tuple->size != 2,
+					      "ant tpl size");
+				sprom->ant_available_a = tuple->data[1];
+				sprom->ant_available_bg = tuple->data[1];
+				break;
+			case SSB_SDIO_CIS_ANTGAIN:
+				GOTO_ERROR_ON(tuple->size != 2,
+					      "antg tpl size");
+				sprom->antenna_gain.ghz24.a0 = tuple->data[1];
+				sprom->antenna_gain.ghz24.a1 = tuple->data[1];
+				sprom->antenna_gain.ghz24.a2 = tuple->data[1];
+				sprom->antenna_gain.ghz24.a3 = tuple->data[1];
+				sprom->antenna_gain.ghz5.a0 = tuple->data[1];
+				sprom->antenna_gain.ghz5.a1 = tuple->data[1];
+				sprom->antenna_gain.ghz5.a2 = tuple->data[1];
+				sprom->antenna_gain.ghz5.a3 = tuple->data[1];
+				break;
+			case SSB_SDIO_CIS_BFLAGS:
+				GOTO_ERROR_ON((tuple->size != 3) &&
+					      (tuple->size != 5),
+					      "bfl tpl size");
+				sprom->boardflags_lo = tuple->data[1] |
+						 ((u16)tuple->data[2] << 8);
+				break;
+			case SSB_SDIO_CIS_LEDS:
+				GOTO_ERROR_ON(tuple->size != 5,
+					      "leds tpl size");
+				sprom->gpio0 = tuple->data[1];
+				sprom->gpio1 = tuple->data[2];
+				sprom->gpio2 = tuple->data[3];
+				sprom->gpio3 = tuple->data[4];
+				break;
+			default:
+				break;
+			}
+			break;
+		default:
+			break;
+		}
+		tuple = tuple->next;
+	}
+
+	return 0;
+error:
+	dev_err(ssb_sdio_dev(bus), "failed to fetch device invariants: %s\n",
+		error_description);
+	return -ENODEV;
+}
+
+void ssb_sdio_exit(struct ssb_bus *bus)
+{
+	if (bus->bustype != SSB_BUSTYPE_SDIO)
+		return;
+	/* Nothing to do here. */
+}
+
+int ssb_sdio_init(struct ssb_bus *bus)
+{
+	if (bus->bustype != SSB_BUSTYPE_SDIO)
+		return 0;
+
+	bus->sdio_sbaddr = ~0;
+
+	return 0;
+}
Index: wireless-testing/drivers/ssb/ssb_private.h
===================================================================
--- wireless-testing.orig/drivers/ssb/ssb_private.h	2009-09-08 19:13:49.000000000 +0200
+++ wireless-testing/drivers/ssb/ssb_private.h	2009-09-08 19:14:13.000000000 +0200
@@ -114,6 +114,46 @@ static inline int ssb_pcmcia_init(struct
 }
 #endif /* CONFIG_SSB_PCMCIAHOST */
 
+/* sdio.c */
+#ifdef CONFIG_SSB_SDIOHOST
+extern int ssb_sdio_get_invariants(struct ssb_bus *bus,
+				     struct ssb_init_invariants *iv);
+
+extern u32 ssb_sdio_scan_read32(struct ssb_bus *bus, u16 offset);
+extern int ssb_sdio_switch_core(struct ssb_bus *bus, struct ssb_device *dev);
+extern int ssb_sdio_scan_switch_coreidx(struct ssb_bus *bus, u8 coreidx);
+extern int ssb_sdio_hardware_setup(struct ssb_bus *bus);
+extern void ssb_sdio_exit(struct ssb_bus *bus);
+extern int ssb_sdio_init(struct ssb_bus *bus);
+
+extern const struct ssb_bus_ops ssb_sdio_ops;
+#else /* CONFIG_SSB_SDIOHOST */
+static inline u32 ssb_sdio_scan_read32(struct ssb_bus *bus, u16 offset)
+{
+	return 0;
+}
+static inline int ssb_sdio_switch_core(struct ssb_bus *bus,
+					 struct ssb_device *dev)
+{
+	return 0;
+}
+static inline int ssb_sdio_scan_switch_coreidx(struct ssb_bus *bus, u8 coreidx)
+{
+	return 0;
+}
+static inline int ssb_sdio_hardware_setup(struct ssb_bus *bus)
+{
+	return 0;
+}
+static inline void ssb_sdio_exit(struct ssb_bus *bus)
+{
+}
+static inline int ssb_sdio_init(struct ssb_bus *bus)
+{
+	return 0;
+}
+#endif /* CONFIG_SSB_SDIOHOST */
+
 
 /* scan.c */
 extern const char *ssb_core_name(u16 coreid);
Index: wireless-testing/include/linux/ssb/ssb.h
===================================================================
--- wireless-testing.orig/include/linux/ssb/ssb.h	2009-09-08 19:13:49.000000000 +0200
+++ wireless-testing/include/linux/ssb/ssb.h	2009-09-08 19:14:13.000000000 +0200
@@ -238,6 +238,7 @@ enum ssb_bustype {
 	SSB_BUSTYPE_SSB,	/* This SSB bus is the system bus */
 	SSB_BUSTYPE_PCI,	/* SSB is connected to PCI bus */
 	SSB_BUSTYPE_PCMCIA,	/* SSB is connected to PCMCIA bus */
+	SSB_BUSTYPE_SDIO,	/* SSB is connected to SDIO bus */
 };
 
 /* board_vendor */
@@ -270,8 +271,12 @@ struct ssb_bus {
 
 	/* The core in the basic address register window. (PCI bus only) */
 	struct ssb_device *mapped_device;
-	/* Currently mapped PCMCIA segment. (bustype == SSB_BUSTYPE_PCMCIA only) */
-	u8 mapped_pcmcia_seg;
+	union {
+		/* Currently mapped PCMCIA segment. (bustype == SSB_BUSTYPE_PCMCIA only) */
+		u8 mapped_pcmcia_seg;
+		/* Current SSB base address window for SDIO. */
+		u32 sdio_sbaddr;
+	};
 	/* Lock for core and segment switching.
 	 * On PCMCIA-host busses this is used to protect the whole MMIO access. */
 	spinlock_t bar_lock;
@@ -282,6 +287,11 @@ struct ssb_bus {
 	struct pci_dev *host_pci;
 	/* Pointer to the PCMCIA device (only if bustype == SSB_BUSTYPE_PCMCIA). */
 	struct pcmcia_device *host_pcmcia;
+	/* Pointer to the SDIO device (only if bustype == SSB_BUSTYPE_SDIO). */
+	struct sdio_func *host_sdio;
+
+	/* See enum ssb_quirks */
+	unsigned int quirks;
 
 #ifdef CONFIG_SSB_SPROM
 	/* Mutex to protect the SPROM writing. */
@@ -336,6 +346,11 @@ struct ssb_bus {
 #endif /* DEBUG */
 };
 
+enum ssb_quirks {
+	/* SDIO connected card requires performing a read after writing a 32-bit value */
+	SSB_QUIRK_SDIO_READ_AFTER_WRITE32	= (1 << 0),
+};
+
 /* The initialization-invariants. */
 struct ssb_init_invariants {
 	/* Versioning information about the PCB. */
@@ -366,6 +381,12 @@ extern int ssb_bus_pcmciabus_register(st
 				      struct pcmcia_device *pcmcia_dev,
 				      unsigned long baseaddr);
 #endif /* CONFIG_SSB_PCMCIAHOST */
+#ifdef CONFIG_SSB_SDIOHOST
+extern int ssb_bus_sdiobus_register(struct ssb_bus *bus,
+				    struct sdio_func *sdio_func,
+				    unsigned int quirks);
+#endif /* CONFIG_SSB_SDIOHOST */
+
 
 extern void ssb_bus_unregister(struct ssb_bus *bus);
 

-- 
Greetings, Michael.

^ permalink raw reply

* [PATCH] b44/b43/b43legacy: Fix switch warnings introduced by SSB-SDIO
From: Michael Buesch @ 2009-09-08 17:33 UTC (permalink / raw)
  To: John W. Linville; +Cc: Broadcom Wireless, linux-wireless, Albert Herranz

This fixes some gcc warnings for switch statements.

Signed-off-by: Michael Buesch <mb@bu3sch.de>


Index: wireless-testing/drivers/net/b44.c
===================================================================
--- wireless-testing.orig/drivers/net/b44.c	2009-09-08 19:21:34.000000000 +0200
+++ wireless-testing/drivers/net/b44.c	2009-09-08 19:21:37.000000000 +0200
@@ -1302,10 +1302,13 @@ static void b44_chip_reset(struct b44 *b
 		     & MDIO_CTRL_MAXF_MASK)));
 		break;
 	case SSB_BUSTYPE_PCI:
-	case SSB_BUSTYPE_PCMCIA:
 		bw32(bp, B44_MDIO_CTRL, (MDIO_CTRL_PREAMBLE |
 		     (0x0d & MDIO_CTRL_MAXF_MASK)));
 		break;
+	case SSB_BUSTYPE_PCMCIA:
+	case SSB_BUSTYPE_SDIO:
+		WARN_ON(1); /* A device with this bus does not exist. */
+		break;
 	}
 
 	br32(bp, B44_MDIO_CTRL);
@@ -1763,10 +1766,13 @@ static void b44_get_drvinfo (struct net_
 	case SSB_BUSTYPE_PCI:
 		strncpy(info->bus_info, pci_name(bus->host_pci), sizeof(info->bus_info));
 		break;
-	case SSB_BUSTYPE_PCMCIA:
 	case SSB_BUSTYPE_SSB:
 		strncpy(info->bus_info, "SSB", sizeof(info->bus_info));
 		break;
+	case SSB_BUSTYPE_PCMCIA:
+	case SSB_BUSTYPE_SDIO:
+		WARN_ON(1); /* A device with this bus does not exist. */
+		break;
 	}
 }
 
Index: wireless-testing/drivers/net/wireless/b43/main.c
===================================================================
--- wireless-testing.orig/drivers/net/wireless/b43/main.c	2009-09-08 19:19:01.000000000 +0200
+++ wireless-testing/drivers/net/wireless/b43/main.c	2009-09-08 19:25:30.000000000 +0200
@@ -4099,16 +4099,20 @@ static void b43_imcfglo_timeouts_workaro
 	    bus->pcicore.dev->id.revision <= 5) {
 		/* IMCFGLO timeouts workaround. */
 		tmp = ssb_read32(dev->dev, SSB_IMCFGLO);
-		tmp &= ~SSB_IMCFGLO_REQTO;
-		tmp &= ~SSB_IMCFGLO_SERTO;
 		switch (bus->bustype) {
 		case SSB_BUSTYPE_PCI:
 		case SSB_BUSTYPE_PCMCIA:
+			tmp &= ~SSB_IMCFGLO_REQTO;
+			tmp &= ~SSB_IMCFGLO_SERTO;
 			tmp |= 0x32;
 			break;
 		case SSB_BUSTYPE_SSB:
+			tmp &= ~SSB_IMCFGLO_REQTO;
+			tmp &= ~SSB_IMCFGLO_SERTO;
 			tmp |= 0x53;
 			break;
+		default:
+			break;
 		}
 		ssb_write32(dev->dev, SSB_IMCFGLO, tmp);
 	}
Index: wireless-testing/drivers/net/wireless/b43legacy/main.c
===================================================================
--- wireless-testing.orig/drivers/net/wireless/b43legacy/main.c	2009-08-23 00:06:40.000000000 +0200
+++ wireless-testing/drivers/net/wireless/b43legacy/main.c	2009-09-08 19:26:03.000000000 +0200
@@ -3106,16 +3106,20 @@ static void b43legacy_imcfglo_timeouts_w
 	    bus->pcicore.dev->id.revision <= 5) {
 		/* IMCFGLO timeouts workaround. */
 		tmp = ssb_read32(dev->dev, SSB_IMCFGLO);
-		tmp &= ~SSB_IMCFGLO_REQTO;
-		tmp &= ~SSB_IMCFGLO_SERTO;
 		switch (bus->bustype) {
 		case SSB_BUSTYPE_PCI:
 		case SSB_BUSTYPE_PCMCIA:
+			tmp &= ~SSB_IMCFGLO_REQTO;
+			tmp &= ~SSB_IMCFGLO_SERTO;
 			tmp |= 0x32;
 			break;
 		case SSB_BUSTYPE_SSB:
+			tmp &= ~SSB_IMCFGLO_REQTO;
+			tmp &= ~SSB_IMCFGLO_SERTO;
 			tmp |= 0x53;
 			break;
+		default:
+			break;
 		}
 		ssb_write32(dev->dev, SSB_IMCFGLO, tmp);
 	}

-- 
Greetings, Michael.

^ permalink raw reply


This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox