* Re: iwlagn: two regressions 2.6.34->2.6.35-rc6
From: Luis R. Rodriguez @ 2010-07-26 20:01 UTC (permalink / raw)
To: Andrew Lutomirski; +Cc: linux-wireless, ilw, Rafael J. Wysocki
In-Reply-To: <AANLkTimo4RV6UMgti0ng1rQYE2eUVh2WLv_WHQZkz30j@mail.gmail.com>
Adding Rafael, in case they are not yet on his list.
Luis
On Mon, Jul 26, 2010 at 12:08 PM, Andrew Lutomirski <luto@mit.edu> wrote:
> Regression 1: I got a SYSASSERT. rmmod/modprobe fixed it. No fancy
> debug because I can't reproduce it.
>
> [ 167.648419] phy0: device no longer idle - scanning
> [ 167.656408] phy0: device now idle
> [ 167.715946] phy0: device no longer idle - scanning
> [ 167.716066] iwlagn 0000:03:00.0: Microcode SW error detected.
> Restarting 0x82000000.
> [ 167.716069] iwlagn 0000:03:00.0: Loaded firmware version: 8.24.2.12
> [ 167.716105] iwlagn 0000:03:00.0: Start IWL Error Log Dump:
> [ 167.716108] iwlagn 0000:03:00.0: Status: 0x0002B2E4, count: 5
> [ 167.716302] iwlagn 0000:03:00.0: Desc
> Time data1 data2 line
> [ 167.716307] iwlagn 0000:03:00.0: SYSASSERT (#05)
> 1042449688 0x00200200 0x00000000 1051
> [ 167.716312] iwlagn 0000:03:00.0: pc blink1 blink2 ilink1 ilink2 hcmd
> [ 167.716316] iwlagn 0000:03:00.0: 0x02CC8 0x02C98 0x02C98 0x008B2
> 0x00000 0x441C0080
> [ 167.716319] iwlagn 0000:03:00.0: CSR values:
> [ 167.716322] iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is
> CSR_INT_PERIODIC_REG)
> [ 167.716350] iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480301
> [ 167.716376] iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X00000040
> [ 167.716401] iwlagn 0000:03:00.0: CSR_INT: 0X00000000
> [ 167.716409] iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000
> [ 167.716418] iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000
> [ 167.716426] iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000008
> [ 167.716435] iwlagn 0000:03:00.0: CSR_RESET: 0X00000000
> [ 167.716444] iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5
> [ 167.716452] iwlagn 0000:03:00.0: CSR_HW_REV: 0X00000024
> [ 167.716461] iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X00000000
> [ 167.716470] iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000804
> [ 167.716478] iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00060000
> [ 167.716487] iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080042
> [ 167.716495] iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X00002183
> [ 167.716504] iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000
> [ 167.716529] iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000
> [ 167.716537] iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000
> [ 167.716563] iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000058
> [ 167.716588] iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88135b6a
> [ 167.716614] iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200
> [ 167.716639] iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00880300
> [ 167.716664] iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a
> [ 167.716673] iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0000
> [ 167.716675] iwlagn 0000:03:00.0: FH register values:
> [ 167.716710] iwlagn 0000:03:00.0:
> FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X133cf500
> [ 167.716730] iwlagn 0000:03:00.0:
> FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X01339760
> [ 167.716750] iwlagn 0000:03:00.0:
> FH_RSCSR_CHNL0_WPTR: 0X00000098
> [ 167.716770] iwlagn 0000:03:00.0:
> FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104
> [ 167.716789] iwlagn 0000:03:00.0:
> FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc
> [ 167.716808] iwlagn 0000:03:00.0:
> FH_MEM_RSSR_RX_STATUS_REG: 0X07030000
> [ 167.716827] iwlagn 0000:03:00.0:
> FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
> [ 167.716846] iwlagn 0000:03:00.0:
> FH_TSSR_TX_STATUS_REG: 0X07ff0001
> [ 167.716865] iwlagn 0000:03:00.0:
> FH_TSSR_TX_ERROR_REG: 0X00000000
> [ 167.716922] iwlagn 0000:03:00.0: Start IWL Event Log Dump: display
> last 20 entries
> [ 167.716944] iwlagn 0000:03:00.0: EVT_LOGT:0151076484:0x00000037:0353
> [ 167.716975] iwlagn 0000:03:00.0: EVT_LOGT:0151076880:0x0000010f:0106
> [ 167.717006] iwlagn 0000:03:00.0: EVT_LOGT:0151076881:0x00000000:0302
> [ 167.717037] iwlagn 0000:03:00.0: EVT_LOGT:0151076905:0x00000038:0353
> [ 167.717051] iwlagn 0000:03:00.0: EVT_LOGT:0151077567:0x441c0080:0401
> [ 167.717066] iwlagn 0000:03:00.0: EVT_LOGT:0151077568:0x441c0080:0700
> [ 167.717080] iwlagn 0000:03:00.0: EVT_LOGT:0151077569:0x00000000:0706
> [ 167.717094] iwlagn 0000:03:00.0: EVT_LOGT:0151077585:0x00000001:0452
> [ 167.717109] iwlagn 0000:03:00.0: EVT_LOGT:0151077587:0x00000001:0452
> [ 167.717139] iwlagn 0000:03:00.0: EVT_LOGT:0151077588:0x00000233:0601
> [ 167.717153] iwlagn 0000:03:00.0: EVT_LOGT:0151077589:0x00000061:0600
> [ 167.717168] iwlagn 0000:03:00.0: EVT_LOGT:0151077591:0x0000007a:0602
> [ 167.717182] iwlagn 0000:03:00.0: EVT_LOGT:0151077597:0x00000100:0706
> [ 167.717213] iwlagn 0000:03:00.0: EVT_LOGT:0151077601:0x00000000:0708
> [ 167.717227] iwlagn 0000:03:00.0: EVT_LOGT:0151077603:0x01000200:0706
> [ 167.717258] iwlagn 0000:03:00.0: EVT_LOGT:0151077613:0x01000200:0725
> [ 167.717263] iwlagn 0000:03:00.0: EVT_LOGT:0151077613:0x00000000:0709
> [ 167.717263] iwlagn 0000:03:00.0: EVT_LOGT:0151077614:0x00000000:0707
> [ 167.717263] iwlagn 0000:03:00.0: EVT_LOGT:0151077614:0x02000201:0706
> [ 167.717263] iwlagn 0000:03:00.0: EVT_LOGT:0151077622:0x00000000:0125
>
>
> Regression 2:
>
> On 2.6.34 my wireless appears to be rock solid (yay -- it's been awhile).
>
> On 2.6.35-rc6, I have an AP here that doesn't work well. It's an
> EnGenius ESR-7750 with latest firmware. I can connect to its 2.4GHz
> radio (usually but it seems to connect more slowly than 2.6.34), but I
> can't always see the 5GHz radio, let alone connect. It's connected
> exactly once out of many tries on 2.6.35-rc6, but it works fine on
> 2.6.34.
>
> In the attached log, you'll see the one successful connection to
> 00:02:6f:6e:d7:6c as well as a failure. The failure is just:
>
> [ 668.569218] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 1)
> [ 668.769269] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 2)
> [ 668.969150] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 3)
> [ 669.169262] wlan0: authentication with 00:02:6f:6e:d7:6c timed out
>
> --Andy
> --
> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply
* pull request: wireless-2.6 2010-07-26
From: John W. Linville @ 2010-07-26 19:49 UTC (permalink / raw)
To: davem; +Cc: linux-wireless, netdev, linux-kernel
Dave,
Here are two more late-bloomers for 2.6.35. Both are tiny and isolated,
and they fix documented regression BUGs as indicated in their commit logs.
The one from me changes a netif_rx to a netif_rx_ni -- the execution
path is in process context, coming from userland. The bug reporter
confirmed that it addressed the problem he reported.
The one from Ming Lei has been in net-next-2.6 for a while already.
More recently, someone posted an identical patch indicated it addressed
the BUG as reported in the cited LKML thread.
I think it would be best to get these into 2.6.35 if at all possible.
Please let me know if there are problems!
Thanks,
John
---
The following changes since commit 3b87956ea645fb4de7e59c7d0aa94de04be72615:
net sched: fix race in mirred device removal (2010-07-24 21:04:20 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6.git master
John W. Linville (1):
wireless: use netif_rx_ni in ieee80211_send_layer2_update
Ming Lei (1):
ath9k: fix dma direction for map/unmap in ath_rx_tasklet
drivers/net/wireless/ath/ath9k/recv.c | 4 ++--
net/mac80211/cfg.c | 2 +-
2 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
index ca6065b..e3e5291 100644
--- a/drivers/net/wireless/ath/ath9k/recv.c
+++ b/drivers/net/wireless/ath/ath9k/recv.c
@@ -844,9 +844,9 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush, bool hp)
int dma_type;
if (edma)
- dma_type = DMA_FROM_DEVICE;
- else
dma_type = DMA_BIDIRECTIONAL;
+ else
+ dma_type = DMA_FROM_DEVICE;
qtype = hp ? ATH9K_RX_QUEUE_HP : ATH9K_RX_QUEUE_LP;
spin_lock_bh(&sc->rx.rxbuflock);
diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c
index c7000a6..67ee34f 100644
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -632,7 +632,7 @@ static void ieee80211_send_layer2_update(struct sta_info *sta)
skb->dev = sta->sdata->dev;
skb->protocol = eth_type_trans(skb, sta->sdata->dev);
memset(skb->cb, 0, sizeof(skb->cb));
- netif_rx(skb);
+ netif_rx_ni(skb);
}
static void sta_apply_parameters(struct ieee80211_local *local,
--
John W. Linville Someday the world will need a hero, and you
linville@tuxdriver.com might be all we have. Be ready.
^ permalink raw reply related
* ath9k: /proc/net/wireless always shows status of 0
From: Ben Greear @ 2010-07-26 19:49 UTC (permalink / raw)
To: linux-wireless
This is with today's wireless-testing (with no extra hacks)
[root@a230-ath9k ~]# cat /proc/net/wireless
Inter-| sta-| Quality | Discarded packets | Missed | WE
face | tus | link level noise | nwid crypt frag retry misc | beacon | 22
wlan0: 0000 67. -43. -256 0 0 0 0 0 0
The interface is running WPA and is passing traffic, so I'd expect some sort of
useful status. Is this a known issue?
[root@a230-ath9k ~]# iwconfig wlan0
wlan0 IEEE 802.11bgn ESSID:"candela-n"
Mode:Managed Frequency:2.412 GHz Access Point: 00:14:D1:C6:D2:54
Bit Rate=117 Mb/s Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=66/70 Signal level=-44 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Thanks,
Ben
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply
* Re: iwlagn: two regressions 2.6.34->2.6.35-rc6
From: Andrew Lutomirski @ 2010-07-26 19:48 UTC (permalink / raw)
To: linux-wireless, ilw
In-Reply-To: <AANLkTimo4RV6UMgti0ng1rQYE2eUVh2WLv_WHQZkz30j@mail.gmail.com>
[-- Attachment #1: Type: text/plain, Size: 1015 bytes --]
On Mon, Jul 26, 2010 at 3:08 PM, Andrew Lutomirski <luto@mit.edu> wrote:
> Regression 2:
>
> On 2.6.34 my wireless appears to be rock solid (yay -- it's been awhile).
>
> On 2.6.35-rc6, I have an AP here that doesn't work well. It's an
> EnGenius ESR-7750 with latest firmware. I can connect to its 2.4GHz
> radio (usually but it seems to connect more slowly than 2.6.34), but I
> can't always see the 5GHz radio, let alone connect. It's connected
> exactly once out of many tries on 2.6.35-rc6, but it works fine on
> 2.6.34.
>
> In the attached log, you'll see the one successful connection to
> 00:02:6f:6e:d7:6c as well as a failure. The failure is just:
>
> [ 668.569218] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 1)
> [ 668.769269] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 2)
> [ 668.969150] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 3)
> [ 669.169262] wlan0: authentication with 00:02:6f:6e:d7:6c timed out
This time with actual attachment.
>
> --Andy
>
[-- Attachment #2: dmesg --]
[-- Type: application/octet-stream, Size: 127130 bytes --]
ffset 0x1
[ 358.055209] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 358.055214] ieee80211 phy1: U iwl_mac_config leave
[ 358.055236] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x04B9, 8 bytes at 185[25]:4
[ 358.055296] ieee80211 phy1: I iwl_mac_tx enter
[ 358.055309] ieee80211 phy1: I iwl_mac_tx leave
[ 358.056417] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 358.063325] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04BA, 28 bytes at 186[26]:4
[ 358.063366] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 358.540124] ieee80211 phy1: U iwl_mac_hw_scan enter
[ 358.540133] ieee80211 phy1: U iwl_scan_initiate Starting scan...
[ 358.540143] ieee80211 phy1: U iwlagn_request_scan Scanning while associated...
[ 358.540150] ieee80211 phy1: U iwlagn_request_scan suspend_time 0x400000 beacon interval 100
[ 358.540157] ieee80211 phy1: U iwlagn_request_scan Kicking off active scan
[ 358.540169] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=1 prob=0x1 [ACTIVE 33]
[ 358.540178] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=2 prob=0x1 [ACTIVE 33]
[ 358.540186] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=3 prob=0x1 [ACTIVE 33]
[ 358.540194] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=4 prob=0x1 [ACTIVE 33]
[ 358.540202] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=5 prob=0x1 [ACTIVE 33]
[ 358.540210] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=6 prob=0x1 [ACTIVE 33]
[ 358.540218] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=7 prob=0x1 [ACTIVE 33]
[ 358.540226] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=8 prob=0x1 [ACTIVE 33]
[ 358.540233] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=9 prob=0x1 [ACTIVE 33]
[ 358.540241] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=10 prob=0x1 [ACTIVE 33]
[ 358.540249] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=11 prob=0x1 [ACTIVE 33]
[ 358.540257] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=12 prob=0x0 [PASSIVE 88]
[ 358.540265] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=13 prob=0x0 [PASSIVE 88]
[ 358.540272] ieee80211 phy1: U iwl_get_channels_for_scan total channels to scan 13
[ 358.540279] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD
[ 358.540286] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 358.540299] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_SCAN_CMD (#80), seq: 0x44BB, 994 bytes at 187[32]:4
[ 358.542511] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 358.542536] ieee80211 phy1: U iwl_mac_hw_scan leave
[ 358.577291] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 358.577312] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 1 [802.11bg] (TSF: 0x00000000:4982D104) - 1 (beacon timer 671186684)
[ 358.612974] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 1 [802.11bg] (TSF: 0x00000000:49835B93) - 12 elapsed=35471 usec
[ 358.614556] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 2 [802.11bg] (TSF: 0x00000000:49836297) - 1 (beacon timer 671149416)
[ 358.648465] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 2 [802.11bg] (TSF: 0x00000000:4983E6D5) - 6 elapsed=33854 usec
[ 358.650238] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 358.782265] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 358.782290] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 3 [802.11bg] (TSF: 0x00000000:4985F110) - 1 (beacon timer 679575280)
[ 358.816470] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 3 [802.11bg] (TSF: 0x00000000:49867681) - 8 elapsed=34161 usec
[ 358.818046] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 4 [802.11bg] (TSF: 0x00000000:49867D8D) - 1 (beacon timer 679539315)
[ 358.852051] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 4 [802.11bg] (TSF: 0x00000000:49870199) - 3 elapsed=33804 usec
[ 358.852383] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 358.987100] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 358.987126] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 5 [802.11bg] (TSF: 0x00000000:49891115) - 1 (beacon timer 687963883)
[ 358.998258] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 5 [802.11bg] (TSF: 0x00000000:49893CB6) - 1 elapsed=11169 usec
[ 358.999868] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 6 [802.11bg] (TSF: 0x00000000:498943C1) - 1 (beacon timer 687950911)
[ 359.035679] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 6 [802.11bg] (TSF: 0x00000000:4989CECF) - 8 elapsed=35598 usec
[ 359.037258] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 7 [802.11bg] (TSF: 0x00000000:4989D5DB) - 1 (beacon timer 687913509)
[ 359.051875] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 7 [802.11bg] (TSF: 0x00000000:498A0E2B) - 1 elapsed=14416 usec
[ 359.053484] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.191760] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.191786] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 8 [802.11bg] (TSF: 0x00000000:498C3111) - 1 (beacon timer 696352495)
[ 359.225709] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 8 [802.11bg] (TSF: 0x00000000:498CB522) - 4 elapsed=33809 usec
[ 359.227290] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 9 [802.11bg] (TSF: 0x00000000:498CBC30) - 1 (beacon timer 696316880)
[ 359.238533] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 9 [802.11bg] (TSF: 0x00000000:498CE7C8) - 1 elapsed=11160 usec
[ 359.240279] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 10 [802.11bg] (TSF: 0x00000000:498CEECD) - 1 (beacon timer 696303923)
[ 359.252212] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 10 [802.11bg] (TSF: 0x00000000:498D1D6E) - 0 elapsed=11937 usec
[ 359.254008] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.396557] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.396582] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 11 [802.11bg] (TSF: 0x00000000:498F510E) - 1 (beacon timer 704741106)
[ 359.430300] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 11 [802.11bg] (TSF: 0x00000000:498FD51A) - 6 elapsed=33804 usec
[ 359.432121] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.601412] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.601435] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 12 [802.11bg] (TSF: 0x00000000:49927178) - 1 (beacon timer 713129608)
[ 359.691735] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 12 [802.11bg] (TSF: 0x00000000:4993D190) - 3 elapsed=90136 usec
[ 359.693328] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.806098] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.806120] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 13 [802.11bg] (TSF: 0x00000000:4995911A) - 1 (beacon timer 721518310)
[ 359.896274] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 13 [802.11bg] (TSF: 0x00000000:4996F13F) - 0 elapsed=90149 usec
[ 359.898060] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.898434] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan complete: 13 channels (TSF 0x4996F9D3:00000000) - 1
[ 359.898444] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan on 2.4GHz took 1359ms
[ 359.898450] ieee80211 phy1: I iwl_rx_scan_complete_notif Setting scan to off
[ 359.898467] ieee80211 phy1: U iwl_bg_scan_completed SCAN complete scan
[ 359.898491] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x04BC, 8 bytes at 188[28]:4
[ 359.898500] ieee80211 phy1: U iwl_mac_hw_scan enter
[ 359.898512] ieee80211 phy1: U iwl_scan_initiate Starting scan...
[ 359.898521] ieee80211 phy1: U iwlagn_request_scan Scanning while associated...
[ 359.898529] ieee80211 phy1: U iwlagn_request_scan suspend_time 0x400000 beacon interval 100
[ 359.898535] ieee80211 phy1: U iwlagn_request_scan Kicking off active scan
[ 359.898547] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=36 prob=0x0 [PASSIVE 88]
[ 359.898555] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=40 prob=0x0 [PASSIVE 88]
[ 359.898563] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=44 prob=0x0 [PASSIVE 88]
[ 359.898571] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=48 prob=0x0 [PASSIVE 88]
[ 359.898579] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=52 prob=0x0 [PASSIVE 88]
[ 359.898587] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=56 prob=0x0 [PASSIVE 88]
[ 359.898595] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=60 prob=0x0 [PASSIVE 88]
[ 359.898603] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=64 prob=0x0 [PASSIVE 88]
[ 359.898611] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=100 prob=0x0 [PASSIVE 88]
[ 359.898619] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=104 prob=0x0 [PASSIVE 88]
[ 359.898627] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=108 prob=0x0 [PASSIVE 88]
[ 359.898635] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=112 prob=0x0 [PASSIVE 88]
[ 359.898643] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=116 prob=0x0 [PASSIVE 88]
[ 359.898651] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=120 prob=0x0 [PASSIVE 88]
[ 359.898659] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=124 prob=0x0 [PASSIVE 88]
[ 359.898667] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=128 prob=0x0 [PASSIVE 88]
[ 359.898675] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=132 prob=0x0 [PASSIVE 88]
[ 359.898683] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=136 prob=0x0 [PASSIVE 88]
[ 359.898691] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=140 prob=0x0 [PASSIVE 88]
[ 359.898699] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=149 prob=0x0 [PASSIVE 88]
[ 359.898707] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=153 prob=0x0 [PASSIVE 88]
[ 359.898716] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=157 prob=0x0 [PASSIVE 88]
[ 359.898734] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 359.898745] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=161 prob=0x0 [PASSIVE 88]
[ 359.898753] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=165 prob=0x0 [PASSIVE 88]
[ 359.898760] ieee80211 phy1: U iwl_get_channels_for_scan total channels to scan 24
[ 359.898766] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD
[ 359.898773] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 359.898785] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_SCAN_CMD (#80), seq: 0x44BD, 1120 bytes at 189[32]:4
[ 359.901358] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 359.901382] ieee80211 phy1: U iwl_mac_hw_scan leave
[ 359.908708] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 359.908732] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 36 [802.11a] (TSF: 0x00000000:49972121) - 1 (beacon timer 725712607)
[ 359.998853] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 36 [802.11a] (TSF: 0x00000000:4998813D) - 0 elapsed=90140 usec
[ 360.000473] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.113477] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.113500] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 40 [802.11a] (TSF: 0x00000000:499A41D9) - 1 (beacon timer 734101031)
[ 360.203842] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 40 [802.11a] (TSF: 0x00000000:499BA1FA) - 0 elapsed=90145 usec
[ 360.205516] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.319612] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.319640] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 44 [802.11a] (TSF: 0x00000000:499D662C) - 1 (beacon timer 742488532)
[ 360.409622] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 44 [802.11a] (TSF: 0x00000000:499EC643) - 0 elapsed=90135 usec
[ 360.411367] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.523238] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.523263] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 48 [802.11a] (TSF: 0x00000000:49A08216) - 1 (beacon timer 750878186)
[ 360.558281] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 48 [802.11a] (TSF: 0x00000000:49A10B36) - 15 elapsed=35104 usec
[ 360.560084] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.727722] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.727742] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 52 [802.11a] (TSF: 0x00000000:49A3A136) - 1 (beacon timer 759267018)
[ 360.818074] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 52 [802.11a] (TSF: 0x00000000:49A50150) - 0 elapsed=90138 usec
[ 360.819696] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.828286] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.932622] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 360.932646] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 56 [802.11a] (TSF: 0x00000000:49A6C145) - 1 (beacon timer 767655611)
[ 360.985719] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 56 [802.11a] (TSF: 0x00000000:49A790E5) - 2 elapsed=53152 usec
[ 360.987525] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.137548] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.137572] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 60 [802.11a] (TSF: 0x00000000:49A9E13D) - 1 (beacon timer 776044227)
[ 361.227678] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 60 [802.11a] (TSF: 0x00000000:49AB4155) - 0 elapsed=90136 usec
[ 361.229291] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.342356] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.342381] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 64 [802.11a] (TSF: 0x00000000:49AD0142) - 1 (beacon timer 784432830)
[ 361.371674] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 64 [802.11a] (TSF: 0x00000000:49AD73AA) - 12 elapsed=29288 usec
[ 361.373239] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.547157] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.547185] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 100 [802.11a] (TSF: 0x00000000:49B02143) - 1 (beacon timer 792821436)
[ 361.637165] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 100 [802.11a] (TSF: 0x00000000:49B1815B) - 0 elapsed=90136 usec
[ 361.638908] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.751963] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.751989] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 104 [802.11a] (TSF: 0x00000000:49B34148) - 1 (beacon timer 801210039)
[ 361.841965] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 104 [802.11a] (TSF: 0x00000000:49B4A15E) - 0 elapsed=90134 usec
[ 361.843767] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.956752] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 361.956777] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 108 [802.11a] (TSF: 0x00000000:49B6613F) - 1 (beacon timer 809598657)
[ 362.046884] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 108 [802.11a] (TSF: 0x00000000:49B7C15A) - 0 elapsed=90139 usec
[ 362.048573] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.161428] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.161450] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 112 [802.11a] (TSF: 0x00000000:49B9814B) - 1 (beacon timer 817987253)
[ 362.251695] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 112 [802.11a] (TSF: 0x00000000:49BAE162) - 0 elapsed=90135 usec
[ 362.253301] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.366167] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.366190] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 116 [802.11a] (TSF: 0x00000000:49BCA150) - 1 (beacon timer 826375855)
[ 362.456326] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 116 [802.11a] (TSF: 0x00000000:49BE0168) - 0 elapsed=90136 usec
[ 362.458107] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.571172] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.571197] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 120 [802.11a] (TSF: 0x00000000:49BFC14B) - 1 (beacon timer 834764469)
[ 362.661308] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 120 [802.11a] (TSF: 0x00000000:49C12164) - 0 elapsed=90137 usec
[ 362.663114] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.775967] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.775992] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 124 [802.11a] (TSF: 0x00000000:49C2E14B) - 1 (beacon timer 843153077)
[ 362.866096] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 124 [802.11a] (TSF: 0x00000000:49C44165) - 0 elapsed=90138 usec
[ 362.867785] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.980650] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 362.980674] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 128 [802.11a] (TSF: 0x00000000:49C60154) - 1 (beacon timer 851541675)
[ 363.070907] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 128 [802.11a] (TSF: 0x00000000:49C7616B) - 0 elapsed=90135 usec
[ 363.072591] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 363.185582] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 363.185608] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 132 [802.11a] (TSF: 0x00000000:49C92159) - 1 (beacon timer 859930279)
[ 363.275730] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 132 [802.11a] (TSF: 0x00000000:49CA8181) - 0 elapsed=90152 usec
[ 363.277357] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 363.390266] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 363.390290] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 136 [802.11a] (TSF: 0x00000000:49CC4153) - 1 (beacon timer 868318893)
[ 363.480329] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 136 [802.11a] (TSF: 0x00000000:49CDA16B) - 0 elapsed=90136 usec
[ 363.482334] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 363.595214] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 363.595239] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 140 [802.11a] (TSF: 0x00000000:49CF6160) - 1 (beacon timer 876707488)
[ 363.685245] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 140 [802.11a] (TSF: 0x00000000:49D0C189) - 0 elapsed=90153 usec
[ 363.687021] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 363.799862] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 363.799885] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 149 [802.11a] (TSF: 0x00000000:49D2815E) - 1 (beacon timer 885096098)
[ 363.826245] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 149 [802.11a] (TSF: 0x00000000:49D2E8A5) - 7 elapsed=26439 usec
[ 363.828030] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 364.004602] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 364.004626] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 153 [802.11a] (TSF: 0x00000000:49D5A122) - 1 (beacon timer 893484766)
[ 364.094868] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 153 [802.11a] (TSF: 0x00000000:49D70139) - 0 elapsed=90135 usec
[ 364.096488] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 364.209531] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 364.209558] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 157 [802.11a] (TSF: 0x00000000:49D8C11D) - 1 (beacon timer 901873379)
[ 364.299666] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 157 [802.11a] (TSF: 0x00000000:49DA2138) - 0 elapsed=90139 usec
[ 364.301337] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 364.414467] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 364.414491] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 161 [802.11a] (TSF: 0x00000000:49DBE1A8) - 1 (beacon timer 910261848)
[ 364.451586] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 161 [802.11a] (TSF: 0x00000000:49DC72AA) - 6 elapsed=37122 usec
[ 364.453262] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 364.619140] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 364.619164] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 165 [802.11a] (TSF: 0x00000000:49DF0126) - 1 (beacon timer 918650585)
[ 364.709169] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 165 [802.11a] (TSF: 0x00000000:49E0614A) - 0 elapsed=90148 usec
[ 364.711105] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 364.711129] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan complete: 24 channels (TSF 0x49E0692A:00000000) - 1
[ 364.711137] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan on 5.2GHz took 4813ms
[ 364.711143] ieee80211 phy1: I iwl_rx_scan_complete_notif Setting scan to off
[ 364.711171] ieee80211 phy1: U iwl_bg_scan_completed SCAN complete scan
[ 364.711192] ieee80211 phy1: U iwl_mac_config enter to channel 4 changed 0x40
[ 364.711201] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x280E active=2 idle=2
[ 364.711210] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x280E active=2 idle=2
[ 364.711219] ieee80211 phy1: U iwl_set_rxon_ht rxon flags 0x4008035 operation mode :0x0 extension channel offset 0x1
[ 364.711228] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 364.711234] ieee80211 phy1: U iwl_mac_config leave
[ 364.711258] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x04BE, 8 bytes at 190[30]:4
[ 364.711310] ieee80211 phy1: I iwl_mac_tx enter
[ 364.711324] ieee80211 phy1: I iwl_mac_tx leave
[ 364.712216] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 364.719353] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04BF, 28 bytes at 191[31]:4
[ 364.719398] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 365.026614] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C0, 28 bytes at 192[0]:4
[ 365.027623] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 365.231618] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C1, 28 bytes at 193[1]:4
[ 365.231670] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 365.333876] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C2, 28 bytes at 194[2]:4
[ 365.333928] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 365.538808] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C3, 28 bytes at 195[3]:4
[ 365.538863] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 365.641234] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C4, 28 bytes at 196[4]:4
[ 365.641309] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 365.743658] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C5, 28 bytes at 197[5]:4
[ 365.743709] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 365.845844] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C6, 28 bytes at 198[6]:4
[ 365.845897] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 365.948278] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C7, 28 bytes at 199[7]:4
[ 365.948353] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 366.050695] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C8, 28 bytes at 200[8]:4
[ 366.050747] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 366.255653] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04C9, 28 bytes at 201[9]:4
[ 366.255712] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 366.460248] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04CA, 28 bytes at 202[10]:4
[ 366.460292] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 366.562913] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04CB, 28 bytes at 203[11]:4
[ 366.562970] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 366.870054] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04CC, 28 bytes at 204[12]:4
[ 366.870105] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 366.972450] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04CD, 28 bytes at 205[13]:4
[ 366.972507] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 368.098699] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04CE, 28 bytes at 206[14]:4
[ 368.098754] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 368.303639] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04CF, 28 bytes at 207[15]:4
[ 368.303696] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 368.405961] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04D0, 28 bytes at 208[16]:4
[ 368.406006] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 368.610854] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04D1, 28 bytes at 209[17]:4
[ 368.610908] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 368.713284] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04D2, 28 bytes at 210[18]:4
[ 368.713346] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 368.815464] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04D3, 28 bytes at 211[19]:4
[ 368.815517] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 368.918071] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04D4, 28 bytes at 212[20]:4
[ 368.918143] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 369.020336] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04D5, 28 bytes at 213[21]:4
[ 369.020407] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 369.122724] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04D6, 28 bytes at 214[22]:4
[ 369.122776] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 369.327662] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04D7, 28 bytes at 215[23]:4
[ 369.327716] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 369.532399] ieee80211 phy1: I iwl_enqueue_hcmd Sending command REPLY_LEDS_CMD (#48), seq: 0x04D8, 12 bytes at 216[24]:4
[ 369.532517] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_LEDS_CMD (0x00000000)
[ 370.556327] ieee80211 phy1: I iwl_enqueue_hcmd Sending command REPLY_LEDS_CMD (#48), seq: 0x04D9, 12 bytes at 217[25]:4
[ 370.556406] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_LEDS_CMD (0x00000000)
[ 372.809249] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04DA, 28 bytes at 218[26]:4
[ 372.809298] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 372.911667] ieee80211 phy1: U iwl_enqueue_hcmd Sending command SENSITIVITY_CMD (#a8), seq: 0x04DB, 28 bytes at 219[27]:4
[ 372.911722] ieee80211 phy1: I iwl_generic_cmd_callback back from SENSITIVITY_CMD (0x00000000)
[ 641.321546] iwlagn 0000:03:00.0: ACTIVATE a non DRIVER active station id 0 addr 00:02:6f:6e:d7:68
[ 641.325043] phy1: Removed STA 00:02:6f:6e:d7:68
[ 641.325152] phy1: Destroyed STA 00:02:6f:6e:d7:68
[ 641.325161] wlan0: deauthenticating from 00:02:6f:6e:d7:68 by local choice (reason=3)
[ 641.325218] phy1: device now idle
[ 641.325282] phy1: device no longer idle - scanning
[ 641.331588] phy1: device now idle
[ 641.339047] cfg80211: Calling CRDA to update world regulatory domain
[ 641.339208] cfg80211: Calling CRDA for country: US
[ 641.360338] cfg80211: Regulatory domain changed to country: US
[ 641.360341] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 641.360345] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 641.360348] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 641.360351] (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 641.360354] (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 641.360357] (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 641.360360] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 641.405369] phy1: device no longer idle - scanning
[ 643.759736] phy1: device now idle
[ 648.763819] phy1: device no longer idle - scanning
[ 651.140797] phy1: device now idle
[ 656.147968] phy1: device no longer idle - scanning
[ 656.147975] ieee80211 phy1: U iwl_mac_config enter to channel 4 changed 0x100
[ 656.147980] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 656.147985] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 656.147988] ieee80211 phy1: U iwl_mac_config leave
[ 656.147992] ieee80211 phy1: U iwl_mac_hw_scan enter
[ 656.147995] ieee80211 phy1: U iwl_scan_initiate Starting scan...
[ 656.148000] ieee80211 phy1: U iwlagn_request_scan Kicking off active scan
[ 656.148010] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=1 prob=0x1 [ACTIVE 33]
[ 656.148015] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=2 prob=0x1 [ACTIVE 33]
[ 656.148019] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=3 prob=0x1 [ACTIVE 33]
[ 656.148023] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=4 prob=0x1 [ACTIVE 33]
[ 656.148027] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=5 prob=0x1 [ACTIVE 33]
[ 656.148031] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=6 prob=0x1 [ACTIVE 33]
[ 656.148035] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=7 prob=0x1 [ACTIVE 33]
[ 656.148039] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=8 prob=0x1 [ACTIVE 33]
[ 656.148048] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=9 prob=0x1 [ACTIVE 33]
[ 656.148051] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=10 prob=0x1 [ACTIVE 33]
[ 656.148061] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=11 prob=0x1 [ACTIVE 33]
[ 656.148063] ieee80211 phy1: U iwl_get_channels_for_scan total channels to scan 11
[ 656.148067] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD
[ 656.148070] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 656.148076] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_SCAN_CMD (#80), seq: 0x44E9, 970 bytes at 233[32]:4
[ 656.150333] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 656.150347] ieee80211 phy1: U iwl_mac_hw_scan leave
[ 656.151155] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 1 [802.11bg] (TSF: 0x00000000:00E2013C) - 1 (beacon timer 604016324)
[ 656.185759] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 1 [802.11bg] (TSF: 0x00000000:00E28808) - 7 elapsed=34508 usec
[ 656.187497] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 2 [802.11bg] (TSF: 0x00000000:00E28F0E) - 1 (beacon timer 603980018)
[ 656.200249] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 2 [802.11bg] (TSF: 0x00000000:00E2C0B3) - 1 elapsed=12709 usec
[ 656.201999] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 3 [802.11bg] (TSF: 0x00000000:00E2C7B8) - 1 (beacon timer 608262216)
[ 656.235989] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 3 [802.11bg] (TSF: 0x00000000:00E34BC2) - 6 elapsed=33802 usec
[ 656.237803] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 4 [802.11bg] (TSF: 0x00000000:00E352CB) - 1 (beacon timer 608226613)
[ 656.248788] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 4 [802.11bg] (TSF: 0x00000000:00E37E74) - 1 elapsed=11177 usec
[ 656.250557] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 5 [802.11bg] (TSF: 0x00000000:00E3857A) - 1 (beacon timer 608213638)
[ 656.265174] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 5 [802.11bg] (TSF: 0x00000000:00E3BE89) - 1 elapsed=14607 usec
[ 656.266966] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 6 [802.11bg] (TSF: 0x00000000:00E3C58F) - 1 (beacon timer 608197233)
[ 656.303335] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 6 [802.11bg] (TSF: 0x00000000:00E45386) - 11 elapsed=36343 usec
[ 656.305126] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 7 [802.11bg] (TSF: 0x00000000:00E45A8C) - 1 (beacon timer 612455796)
[ 656.340117] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 7 [802.11bg] (TSF: 0x00000000:00E4E2F2) - 7 elapsed=34918 usec
[ 656.341833] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 8 [802.11bg] (TSF: 0x00000000:00E4E9F8) - 1 (beacon timer 612419080)
[ 656.353007] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 8 [802.11bg] (TSF: 0x00000000:00E515A3) - 0 elapsed=11179 usec
[ 656.354882] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 9 [802.11bg] (TSF: 0x00000000:00E51CA9) - 1 (beacon timer 612406103)
[ 656.367166] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 9 [802.11bg] (TSF: 0x00000000:00E54C9E) - 0 elapsed=12277 usec
[ 656.369101] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 10 [802.11bg] (TSF: 0x00000000:00E553A4) - 1 (beacon timer 612392028)
[ 656.403159] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 10 [802.11bg] (TSF: 0x00000000:00E5D8BF) - 2 elapsed=34075 usec
[ 656.404844] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 11 [802.11bg] (TSF: 0x00000000:00E5DFC7) - 1 (beacon timer 616652857)
[ 656.438647] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 11 [802.11bg] (TSF: 0x00000000:00E663DA) - 8 elapsed=33811 usec
[ 656.440375] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan complete: 11 channels (TSF 0x00E66AF6:00000000) - 1
[ 656.440384] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan on 2.4GHz took 293ms
[ 656.440391] ieee80211 phy1: I iwl_rx_scan_complete_notif Setting scan to off
[ 656.440420] ieee80211 phy1: U iwl_bg_scan_completed SCAN complete scan
[ 656.440449] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x04EA, 8 bytes at 234[10]:4
[ 656.440464] ieee80211 phy1: U iwl_mac_hw_scan enter
[ 656.440470] ieee80211 phy1: U iwl_scan_initiate Starting scan...
[ 656.440479] ieee80211 phy1: U iwlagn_request_scan Kicking off active scan
[ 656.440490] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=36 prob=0x0 [PASSIVE 110]
[ 656.440499] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=40 prob=0x0 [PASSIVE 110]
[ 656.440507] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=44 prob=0x0 [PASSIVE 110]
[ 656.440516] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=48 prob=0x0 [PASSIVE 110]
[ 656.440524] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=52 prob=0x0 [PASSIVE 110]
[ 656.440532] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=56 prob=0x0 [PASSIVE 110]
[ 656.440541] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=60 prob=0x0 [PASSIVE 110]
[ 656.440549] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=64 prob=0x0 [PASSIVE 110]
[ 656.440557] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=100 prob=0x0 [PASSIVE 110]
[ 656.440565] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=104 prob=0x0 [PASSIVE 110]
[ 656.440574] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=108 prob=0x0 [PASSIVE 110]
[ 656.440582] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=112 prob=0x0 [PASSIVE 110]
[ 656.440590] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=116 prob=0x0 [PASSIVE 110]
[ 656.440598] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=132 prob=0x0 [PASSIVE 110]
[ 656.440606] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=136 prob=0x0 [PASSIVE 110]
[ 656.440615] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=140 prob=0x0 [PASSIVE 110]
[ 656.440623] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=149 prob=0x0 [PASSIVE 110]
[ 656.440631] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=153 prob=0x0 [PASSIVE 110]
[ 656.440640] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=157 prob=0x0 [PASSIVE 110]
[ 656.440648] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=161 prob=0x0 [PASSIVE 110]
[ 656.440656] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=165 prob=0x0 [PASSIVE 110]
[ 656.440663] ieee80211 phy1: U iwl_get_channels_for_scan total channels to scan 21
[ 656.440680] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 656.440690] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD
[ 656.440697] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 656.440709] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_SCAN_CMD (#80), seq: 0x44EB, 1084 bytes at 235[32]:4
[ 656.442625] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 656.442646] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 36 [802.11a] (TSF: 0x00000000:00E673C9) - 1 (beacon timer 616614967)
[ 656.442655] ieee80211 phy1: U iwl_mac_hw_scan leave
[ 656.555528] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 36 [802.11a] (TSF: 0x00000000:00E82BEB) - 0 elapsed=112674 usec
[ 656.557137] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 40 [802.11a] (TSF: 0x00000000:00E8330F) - 1 (beacon timer 620797169)
[ 656.668064] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 40 [802.11a] (TSF: 0x00000000:00E9E377) - 2 elapsed=110696 usec
[ 656.669679] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 44 [802.11a] (TSF: 0x00000000:00E9EA9C) - 1 (beacon timer 624981348)
[ 656.782579] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 44 [802.11a] (TSF: 0x00000000:00EBA2D6) - 0 elapsed=112698 usec
[ 656.784281] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 48 [802.11a] (TSF: 0x00000000:00EBA9FB) - 1 (beacon timer 629163525)
[ 656.810553] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 48 [802.11a] (TSF: 0x00000000:00EC109A) - 23 elapsed=26271 usec
[ 656.812292] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 52 [802.11a] (TSF: 0x00000000:00EC17BE) - 1 (beacon timer 633432130)
[ 656.925186] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 52 [802.11a] (TSF: 0x00000000:00EDCFE5) - 0 elapsed=112679 usec
[ 656.926816] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 56 [802.11a] (TSF: 0x00000000:00EDD70A) - 1 (beacon timer 637614326)
[ 657.027263] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 56 [802.11a] (TSF: 0x00000000:00EF5F53) - 2 elapsed=100425 usec
[ 657.029142] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 60 [802.11a] (TSF: 0x00000000:00EF6676) - 1 (beacon timer 641808778)
[ 657.141968] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 60 [802.11a] (TSF: 0x00000000:00F11EB0) - 0 elapsed=112698 usec
[ 657.143588] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 64 [802.11a] (TSF: 0x00000000:00F125D4) - 1 (beacon timer 645990956)
[ 657.170120] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 64 [802.11a] (TSF: 0x00000000:00F18CA7) - 8 elapsed=26323 usec
[ 657.171751] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 100 [802.11a] (TSF: 0x00000000:00F193CB) - 1 (beacon timer 645962805)
[ 657.284526] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 100 [802.11a] (TSF: 0x00000000:00F34C06) - 0 elapsed=112699 usec
[ 657.286259] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 104 [802.11a] (TSF: 0x00000000:00F35327) - 1 (beacon timer 650144985)
[ 657.398965] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 104 [802.11a] (TSF: 0x00000000:00F50B66) - 0 elapsed=112703 usec
[ 657.400777] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 108 [802.11a] (TSF: 0x00000000:00F51288) - 1 (beacon timer 654327160)
[ 657.513584] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 108 [802.11a] (TSF: 0x00000000:00F6CAC6) - 0 elapsed=112702 usec
[ 657.515320] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 112 [802.11a] (TSF: 0x00000000:00F6D1E5) - 1 (beacon timer 658509339)
[ 657.628233] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 112 [802.11a] (TSF: 0x00000000:00F88A24) - 0 elapsed=112703 usec
[ 657.629862] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 116 [802.11a] (TSF: 0x00000000:00F89144) - 1 (beacon timer 666988220)
[ 657.742551] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 116 [802.11a] (TSF: 0x00000000:00FA4982) - 0 elapsed=112702 usec
[ 657.744374] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 132 [802.11a] (TSF: 0x00000000:00FA50A2) - 1 (beacon timer 671170398)
[ 657.857120] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 132 [802.11a] (TSF: 0x00000000:00FC08E6) - 0 elapsed=112708 usec
[ 657.858921] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 136 [802.11a] (TSF: 0x00000000:00FC100B) - 1 (beacon timer 675352565)
[ 657.971836] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 136 [802.11a] (TSF: 0x00000000:00FDC84A) - 0 elapsed=112703 usec
[ 657.973444] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 140 [802.11a] (TSF: 0x00000000:00FDCF6D) - 1 (beacon timer 679534739)
[ 658.086242] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 140 [802.11a] (TSF: 0x00000000:00FF87AB) - 0 elapsed=112702 usec
[ 658.087962] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 149 [802.11a] (TSF: 0x00000000:00FF8ECA) - 1 (beacon timer 683716918)
[ 658.118907] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 149 [802.11a] (TSF: 0x00000000:010006D5) - 6 elapsed=30731 usec
[ 658.120524] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 153 [802.11a] (TSF: 0x00000000:01000DF5) - 1 (beacon timer 683684363)
[ 658.233243] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 153 [802.11a] (TSF: 0x00000000:0101C635) - 0 elapsed=112704 usec
[ 658.235065] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 157 [802.11a] (TSF: 0x00000000:0101CD53) - 1 (beacon timer 687866541)
[ 658.347967] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 157 [802.11a] (TSF: 0x00000000:01038595) - 0 elapsed=112706 usec
[ 658.349610] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 161 [802.11a] (TSF: 0x00000000:01038CB2) - 1 (beacon timer 696345421)
[ 658.395442] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 161 [802.11a] (TSF: 0x00000000:01043EFE) - 9 elapsed=45644 usec
[ 658.397056] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 165 [802.11a] (TSF: 0x00000000:01044620) - 1 (beacon timer 696297952)
[ 658.509847] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 165 [802.11a] (TSF: 0x00000000:0105FE61) - 0 elapsed=112705 usec
[ 658.511575] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan complete: 21 channels (TSF 0x0106057E:00000000) - 1
[ 658.511584] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan on 5.2GHz took 2071ms
[ 658.511591] ieee80211 phy1: I iwl_rx_scan_complete_notif Setting scan to off
[ 658.511616] ieee80211 phy1: U iwl_bg_scan_completed SCAN complete scan
[ 658.511634] ieee80211 phy1: U iwl_mac_config enter to channel 4 changed 0x40
[ 658.511643] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x240E active=2 idle=1
[ 658.511654] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 658.511660] ieee80211 phy1: U iwl_mac_config leave
[ 658.511666] phy1: device now idle
[ 658.511672] ieee80211 phy1: U iwl_mac_config enter to channel 4 changed 0x100
[ 658.511679] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 658.511686] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 658.511692] ieee80211 phy1: U iwl_mac_config leave
[ 658.511713] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x04EC, 8 bytes at 236[12]:4
[ 658.512173] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 658.513824] phy1: device no longer idle - scanning
[ 658.513834] ieee80211 phy1: U iwl_mac_config enter to channel 4 changed 0x100
[ 658.513841] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 658.513848] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 658.513855] ieee80211 phy1: U iwl_mac_config leave
[ 658.513864] ieee80211 phy1: U iwl_mac_hw_scan enter
[ 658.513871] ieee80211 phy1: U iwl_scan_initiate Starting scan...
[ 658.513880] ieee80211 phy1: U iwlagn_request_scan Kicking off active scan
[ 658.513893] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=40 prob=0x2 [PASSIVE 110]
[ 658.513902] ieee80211 phy1: U iwl_get_channels_for_scan total channels to scan 1
[ 658.513910] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD
[ 658.513918] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 658.513931] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_SCAN_CMD (#80), seq: 0x44ED, 844 bytes at 237[32]:4
[ 658.515844] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 658.515864] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 40 [802.11a] (TSF: 0x00000000:01061631) - 1 (beacon timer 700475854)
[ 658.515888] ieee80211 phy1: U iwl_mac_hw_scan leave
[ 658.516024] wlan0: deauthenticating from 00:02:6f:6e:d7:6c by local choice (reason=3)
[ 658.516054] ieee80211 phy1: I iwl_mac_tx enter
[ 658.516066] ieee80211 phy1: I iwl_mac_tx leave
[ 658.602591] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 40 [802.11a] (TSF: 0x00000000:01076837) - 2 elapsed=86534 usec
[ 658.604210] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan complete: 1 channels (TSF 0x01076F56:00000000) - 1
[ 658.604220] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan on 5.2GHz took 90ms
[ 658.604227] ieee80211 phy1: I iwl_rx_scan_complete_notif Setting scan to off
[ 658.604247] ieee80211 phy1: U iwl_bg_scan_completed SCAN complete scan
[ 658.604285] ieee80211 phy1: U iwl_mac_config enter to channel 4 changed 0x40
[ 658.604295] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x240E active=2 idle=1
[ 658.604307] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 658.604313] ieee80211 phy1: U iwl_mac_config leave
[ 658.604336] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x04EE, 8 bytes at 238[14]:4
[ 658.604367] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x40
[ 658.604377] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x240E active=2 idle=1
[ 658.604386] ieee80211 phy1: U iwl_set_rxon_channel Staging channel set to 40 [1]
[ 658.604398] ieee80211 phy1: U iwl_commit_rxon Sending RXON
[ 658.604401] * without RXON_FILTER_ASSOC_MSK
[ 658.604403] * channel = 40
[ 658.604405] * bssid = 00:02:6f:6e:d7:68
[ 658.604412] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON
[ 658.604419] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON
[ 658.604429] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_RXON (#10), seq: 0x04EF, 54 bytes at 239[15]:4
[ 658.604706] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 658.606489] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON
[ 658.606509] ieee80211 phy1: U iwl_commit_rxon Return from !new_assoc RXON.
[ 658.606516] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode stations in driver
[ 658.606524] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode active for station 15
[ 658.606532] ieee80211 phy1: U iwl_restore_stations Restoring all known stations ... start.
[ 658.606540] ieee80211 phy1: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff
[ 658.606548] ieee80211 phy1: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously
[ 658.606556] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA
[ 658.606563] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA
[ 658.606574] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x04F0, 96 bytes at 240[16]:4
[ 658.606617] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA
[ 658.606633] ieee80211 phy1: U iwl_process_add_sta_resp Processing response for adding station 15
[ 658.606640] ieee80211 phy1: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 658.606647] ieee80211 phy1: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode
[ 658.606655] ieee80211 phy1: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff
[ 658.606663] ieee80211 phy1: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff
[ 658.606674] ieee80211 phy1: U is_lq_table_valid Channel 40 is not an HT channel
[ 658.606681] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD
[ 658.606688] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 658.606699] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x04F1, 92 bytes at 241[17]:4
[ 658.606748] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 658.606768] ieee80211 phy1: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15
[ 658.606776] ieee80211 phy1: U iwl_restore_stations Restoring all known stations .... complete.
[ 658.606784] ieee80211 phy1: U iwl_print_rx_config_cmd RX CONFIG:
[ 658.606792] iwl data: 00000000: 00 16 eb 05 61 ea 00 00 00 02 6f 6e d7 68 00 00 ....a.....on.h..
[ 658.606799] iwl data: 00000010: 00 16 eb 05 61 ea 00 00 03 00 0e 24 15 03 00 00 ....a......$....
[ 658.606805] iwl data: 00000020: 10 80 00 00 04 00 00 00 28 00 ff ff ff 00 00 00 ........(.......
[ 658.606812] iwl data: 00000030: 00 00 ..
[ 658.606818] ieee80211 phy1: U iwl_print_rx_config_cmd u16 channel: 0x28
[ 658.606825] ieee80211 phy1: U iwl_print_rx_config_cmd u32 flags: 0x00008010
[ 658.606832] ieee80211 phy1: U iwl_print_rx_config_cmd u32 filter_flags: 0x00000004
[ 658.606838] ieee80211 phy1: U iwl_print_rx_config_cmd u8 dev_type: 0x3
[ 658.606844] ieee80211 phy1: U iwl_print_rx_config_cmd u8 ofdm_basic_rates: 0x15
[ 658.606851] ieee80211 phy1: U iwl_print_rx_config_cmd u8 cck_basic_rates: 0x03
[ 658.606857] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] node_addr: 00:16:eb:05:61:ea
[ 658.606864] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] bssid_addr: 00:02:6f:6e:d7:68
[ 658.606871] ieee80211 phy1: U iwl_print_rx_config_cmd u16 assoc_id: 0x0
[ 658.606882] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x04F2, 8 bytes at 242[18]:4
[ 658.606890] ieee80211 phy1: U iwl_mac_config leave
[ 658.606900] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 1)
[ 658.606919] ieee80211 phy1: I iwl_mac_tx enter
[ 658.606931] ieee80211 phy1: I iwl_mac_tx leave
[ 658.607110] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 658.806059] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 2)
[ 658.806088] ieee80211 phy1: I iwl_mac_tx enter
[ 658.806105] ieee80211 phy1: I iwl_mac_tx leave
[ 658.807290] wlan0: authenticated
[ 658.807317] phy1: device now idle
[ 658.807327] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x100
[ 658.807335] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 658.807342] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 658.807348] ieee80211 phy1: U iwl_mac_config leave
[ 658.807355] ieee80211 phy1: U iwl_mac_config enter to channel 4 changed 0x40
[ 658.807364] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x240E active=2 idle=1
[ 658.807372] ieee80211 phy1: U iwl_set_rxon_channel Staging channel set to 4 [0]
[ 658.807384] ieee80211 phy1: U iwl_commit_rxon Sending RXON
[ 658.807386] * without RXON_FILTER_ASSOC_MSK
[ 658.807389] * channel = 4
[ 658.807390] * bssid = 00:02:6f:6e:d7:68
[ 658.807398] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON
[ 658.807405] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON
[ 658.807416] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_RXON (#10), seq: 0x04F3, 54 bytes at 243[19]:4
[ 658.810399] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON
[ 658.810446] ieee80211 phy1: U iwl_commit_rxon Return from !new_assoc RXON.
[ 658.810454] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode stations in driver
[ 658.810462] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode active for station 15
[ 658.810469] ieee80211 phy1: U iwl_restore_stations Restoring all known stations ... start.
[ 658.810477] ieee80211 phy1: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff
[ 658.810486] ieee80211 phy1: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously
[ 658.810494] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA
[ 658.810501] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA
[ 658.810512] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x04F4, 96 bytes at 244[20]:4
[ 658.810568] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA
[ 658.810586] ieee80211 phy1: U iwl_process_add_sta_resp Processing response for adding station 15
[ 658.810592] ieee80211 phy1: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 658.810600] ieee80211 phy1: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode
[ 658.810608] ieee80211 phy1: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff
[ 658.810615] ieee80211 phy1: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff
[ 658.810629] ieee80211 phy1: U is_lq_table_valid Channel 4 is not an HT channel
[ 658.810636] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD
[ 658.810643] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 658.810654] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x04F5, 92 bytes at 245[21]:4
[ 658.810717] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 658.810745] ieee80211 phy1: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15
[ 658.810754] ieee80211 phy1: U iwl_restore_stations Restoring all known stations .... complete.
[ 658.810761] ieee80211 phy1: U iwl_print_rx_config_cmd RX CONFIG:
[ 658.810770] iwl data: 00000000: 00 16 eb 05 61 ea 00 00 00 02 6f 6e d7 68 00 00 ....a.....on.h..
[ 658.810777] iwl data: 00000010: 00 16 eb 05 61 ea 00 00 03 00 0e 24 15 03 00 00 ....a......$....
[ 658.810784] iwl data: 00000020: 15 80 00 00 04 00 00 00 04 00 ff ff ff 00 00 00 ................
[ 658.810790] iwl data: 00000030: 00 00 ..
[ 658.810797] ieee80211 phy1: U iwl_print_rx_config_cmd u16 channel: 0x4
[ 658.810803] ieee80211 phy1: U iwl_print_rx_config_cmd u32 flags: 0x00008015
[ 658.810810] ieee80211 phy1: U iwl_print_rx_config_cmd u32 filter_flags: 0x00000004
[ 658.810816] ieee80211 phy1: U iwl_print_rx_config_cmd u8 dev_type: 0x3
[ 658.810822] ieee80211 phy1: U iwl_print_rx_config_cmd u8 ofdm_basic_rates: 0x15
[ 658.810829] ieee80211 phy1: U iwl_print_rx_config_cmd u8 cck_basic_rates: 0x03
[ 658.810836] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] node_addr: 00:16:eb:05:61:ea
[ 658.810842] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] bssid_addr: 00:02:6f:6e:d7:68
[ 658.810849] ieee80211 phy1: U iwl_print_rx_config_cmd u16 assoc_id: 0x0
[ 658.810862] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x04F6, 8 bytes at 246[22]:4
[ 658.810871] ieee80211 phy1: U iwl_mac_config leave
[ 658.810903] phy1: device no longer idle - working
[ 658.810910] ieee80211 phy1: U iwl_mac_config enter to channel 4 changed 0x100
[ 658.810917] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 658.810925] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 658.810931] ieee80211 phy1: U iwl_mac_config leave
[ 658.810939] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x40
[ 658.810947] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x240E active=2 idle=1
[ 658.810956] ieee80211 phy1: U iwl_set_rxon_channel Staging channel set to 40 [1]
[ 658.810967] ieee80211 phy1: U iwl_commit_rxon Sending RXON
[ 658.810970] * without RXON_FILTER_ASSOC_MSK
[ 658.810972] * channel = 40
[ 658.810974] * bssid = 00:02:6f:6e:d7:68
[ 658.810980] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON
[ 658.810987] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON
[ 658.810997] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_RXON (#10), seq: 0x04F7, 54 bytes at 247[23]:4
[ 658.811097] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 658.813047] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON
[ 658.813066] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 658.813075] ieee80211 phy1: U iwl_commit_rxon Return from !new_assoc RXON.
[ 658.813083] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode stations in driver
[ 658.813090] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode active for station 15
[ 658.813097] ieee80211 phy1: U iwl_restore_stations Restoring all known stations ... start.
[ 658.813104] ieee80211 phy1: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff
[ 658.813112] ieee80211 phy1: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously
[ 658.813120] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA
[ 658.813127] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA
[ 658.813137] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x04F8, 96 bytes at 248[24]:4
[ 658.815049] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA
[ 658.815073] ieee80211 phy1: U iwl_process_add_sta_resp Processing response for adding station 15
[ 658.815080] ieee80211 phy1: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 658.815087] ieee80211 phy1: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode
[ 658.815095] ieee80211 phy1: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff
[ 658.815103] ieee80211 phy1: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff
[ 658.815113] ieee80211 phy1: U is_lq_table_valid Channel 40 is not an HT channel
[ 658.815120] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD
[ 658.815128] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 658.815138] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x04F9, 92 bytes at 249[25]:4
[ 658.815216] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 658.815237] ieee80211 phy1: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15
[ 658.815245] ieee80211 phy1: U iwl_restore_stations Restoring all known stations .... complete.
[ 658.815269] ieee80211 phy1: U iwl_print_rx_config_cmd RX CONFIG:
[ 658.815276] iwl data: 00000000: 00 16 eb 05 61 ea 00 00 00 02 6f 6e d7 68 00 00 ....a.....on.h..
[ 658.815286] iwl data: 00000010: 00 16 eb 05 61 ea 00 00 03 00 0e 24 15 03 00 00 ....a......$....
[ 658.815295] iwl data: 00000020: 10 80 00 00 04 00 00 00 28 00 ff ff ff 00 00 00 ........(.......
[ 658.815303] iwl data: 00000030: 00 00 ..
[ 658.815312] ieee80211 phy1: U iwl_print_rx_config_cmd u16 channel: 0x28
[ 658.815319] ieee80211 phy1: U iwl_print_rx_config_cmd u32 flags: 0x00008010
[ 658.815327] ieee80211 phy1: U iwl_print_rx_config_cmd u32 filter_flags: 0x00000004
[ 658.815335] ieee80211 phy1: U iwl_print_rx_config_cmd u8 dev_type: 0x3
[ 658.815342] ieee80211 phy1: U iwl_print_rx_config_cmd u8 ofdm_basic_rates: 0x15
[ 658.815350] ieee80211 phy1: U iwl_print_rx_config_cmd u8 cck_basic_rates: 0x03
[ 658.815358] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] node_addr: 00:16:eb:05:61:ea
[ 658.815366] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] bssid_addr: 00:02:6f:6e:d7:68
[ 658.815374] ieee80211 phy1: U iwl_print_rx_config_cmd u16 assoc_id: 0x0
[ 658.815388] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x04FA, 8 bytes at 250[26]:4
[ 658.815398] ieee80211 phy1: U iwl_mac_config leave
[ 658.815411] wlan0: associate with 00:02:6f:6e:d7:6c (try 1)
[ 658.815437] ieee80211 phy1: I iwl_mac_tx enter
[ 658.815450] ieee80211 phy1: I iwl_mac_tx leave
[ 658.815620] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 659.015287] wlan0: associate with 00:02:6f:6e:d7:6c (try 2)
[ 659.015316] ieee80211 phy1: I iwl_mac_tx enter
[ 659.015332] ieee80211 phy1: I iwl_mac_tx leave
[ 659.017111] wlan0: RX AssocResp from 00:02:6f:6e:d7:6c (capab=0x831 status=0 aid=2)
[ 659.017119] wlan0: associated
[ 659.017133] phy1: Allocated STA 00:02:6f:6e:d7:6c
[ 659.017146] ieee80211 phy1: U iwlagn_mac_sta_add received request to add station 00:02:6f:6e:d7:6c
[ 659.017153] ieee80211 phy1: U iwlagn_mac_sta_add proceeding to add station 00:02:6f:6e:d7:6c
[ 659.017162] ieee80211 phy1: U iwl_prep_station Add STA to driver ID 0: 00:02:6f:6e:d7:6c
[ 659.017169] ieee80211 phy1: U iwl_set_ht_add_station spatial multiplexing power save mode: disabled
[ 659.017178] ieee80211 phy1: U iwl_send_add_sta Adding sta 0 (00:02:6f:6e:d7:6c) synchronously
[ 659.017187] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA
[ 659.017194] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.017206] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x04FB, 96 bytes at 251[27]:4
[ 659.017284] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.017320] ieee80211 phy1: U iwl_process_add_sta_resp Processing response for adding station 0
[ 659.017329] ieee80211 phy1: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 659.017338] ieee80211 phy1: U iwl_sta_ucode_activate Added STA id 0 addr 00:02:6f:6e:d7:6c to uCode
[ 659.017349] ieee80211 phy1: U iwl_process_add_sta_resp Added station id 0 addr 00:02:6f:6e:d7:6c
[ 659.017358] ieee80211 phy1: U iwl_process_add_sta_resp Added station according to cmd buffer 00:02:6f:6e:d7:6c
[ 659.017370] ieee80211 phy1: U iwlagn_mac_sta_add Initializing rate scaling for station 00:02:6f:6e:d7:6c
[ 659.017386] ieee80211 phy1: U is_lq_table_valid Channel 40 is not an HT channel
[ 659.017395] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD
[ 659.017404] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.017417] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x04FC, 92 bytes at 252[28]:4
[ 659.017470] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.017490] ieee80211 phy1: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0
[ 659.017889] phy1: Inserted STA 00:02:6f:6e:d7:6c
[ 659.017899] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x42
[ 659.017908] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x280E active=2 idle=2
[ 659.017918] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x280E active=2 idle=2
[ 659.017926] ieee80211 phy1: U iwl_set_rxon_ht rxon flags 0x4408010 operation mode :0x0 extension channel offset 0x3
[ 659.017938] ieee80211 phy1: U iwl_commit_rxon Sending RXON
[ 659.017941] * without RXON_FILTER_ASSOC_MSK
[ 659.017943] * channel = 40
[ 659.017945] * bssid = 00:02:6f:6e:d7:68
[ 659.017951] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON
[ 659.017958] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON
[ 659.017968] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_RXON (#10), seq: 0x04FD, 54 bytes at 253[29]:4
[ 659.019459] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON
[ 659.019480] ieee80211 phy1: I iwl_tt_handler Queueing thermal throttling work.
[ 659.019500] ieee80211 phy1: U iwl_commit_rxon Return from !new_assoc RXON.
[ 659.019507] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode stations in driver
[ 659.019514] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode active for station 0
[ 659.019521] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode active for station 15
[ 659.019528] ieee80211 phy1: U iwl_restore_stations Restoring all known stations ... start.
[ 659.019536] ieee80211 phy1: U iwl_restore_stations Restoring sta 00:02:6f:6e:d7:6c
[ 659.019542] ieee80211 phy1: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff
[ 659.019550] ieee80211 phy1: U iwl_send_add_sta Adding sta 0 (00:02:6f:6e:d7:6c) synchronously
[ 659.019557] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA
[ 659.019564] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.019575] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x04FE, 96 bytes at 254[30]:4
[ 659.021458] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.021486] ieee80211 phy1: U iwl_process_add_sta_resp Processing response for adding station 0
[ 659.021493] ieee80211 phy1: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 659.021501] ieee80211 phy1: U iwl_sta_ucode_activate Added STA id 0 addr 00:02:6f:6e:d7:6c to uCode
[ 659.021509] ieee80211 phy1: U iwl_process_add_sta_resp Added station id 0 addr 00:02:6f:6e:d7:6c
[ 659.021516] ieee80211 phy1: U iwl_process_add_sta_resp Added station according to cmd buffer 00:02:6f:6e:d7:6c
[ 659.021529] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD
[ 659.021536] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.021548] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x04FF, 92 bytes at 255[31]:4
[ 659.021623] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.021647] ieee80211 phy1: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0
[ 659.021658] ieee80211 phy1: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously
[ 659.021665] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA
[ 659.021672] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.021682] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x0400, 96 bytes at 0[0]:4
[ 659.021754] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.021772] ieee80211 phy1: U iwl_process_add_sta_resp Processing response for adding station 15
[ 659.021779] ieee80211 phy1: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 659.021786] ieee80211 phy1: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode
[ 659.021794] ieee80211 phy1: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff
[ 659.021801] ieee80211 phy1: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff
[ 659.021811] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD
[ 659.021818] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.021828] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x0401, 92 bytes at 1[1]:4
[ 659.021883] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.021901] ieee80211 phy1: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15
[ 659.021909] ieee80211 phy1: U iwl_restore_stations Restoring all known stations .... complete.
[ 659.021917] ieee80211 phy1: U iwl_print_rx_config_cmd RX CONFIG:
[ 659.021925] iwl data: 00000000: 00 16 eb 05 61 ea 00 00 00 02 6f 6e d7 68 00 00 ....a.....on.h..
[ 659.021932] iwl data: 00000010: 00 16 eb 05 61 ea 00 00 03 00 0e 28 15 03 00 00 ....a......(....
[ 659.021939] iwl data: 00000020: 10 80 40 04 04 00 00 00 28 00 ff ff ff 00 00 00 ..@.....(.......
[ 659.021945] iwl data: 00000030: 00 00 ..
[ 659.021952] ieee80211 phy1: U iwl_print_rx_config_cmd u16 channel: 0x28
[ 659.021958] ieee80211 phy1: U iwl_print_rx_config_cmd u32 flags: 0x04408010
[ 659.021964] ieee80211 phy1: U iwl_print_rx_config_cmd u32 filter_flags: 0x00000004
[ 659.021971] ieee80211 phy1: U iwl_print_rx_config_cmd u8 dev_type: 0x3
[ 659.021977] ieee80211 phy1: U iwl_print_rx_config_cmd u8 ofdm_basic_rates: 0x15
[ 659.021983] ieee80211 phy1: U iwl_print_rx_config_cmd u8 cck_basic_rates: 0x03
[ 659.021990] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] node_addr: 00:16:eb:05:61:ea
[ 659.021997] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] bssid_addr: 00:02:6f:6e:d7:68
[ 659.022026] ieee80211 phy1: U iwl_print_rx_config_cmd u16 assoc_id: 0x0
[ 659.022040] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x0402, 8 bytes at 2[2]:4
[ 659.022050] ieee80211 phy1: U iwl_mac_config leave
[ 659.022064] ieee80211 phy1: U iwl_bss_info_changed changes = 0xFD
[ 659.022073] ieee80211 phy1: U iwl_bss_info_changed BSSID 00:02:6f:6e:d7:6c
[ 659.022081] ieee80211 phy1: U iwl_bss_info_changed ERP_PREAMBLE 1
[ 659.022087] ieee80211 phy1: U iwl_ht_conf enter:
[ 659.022094] ieee80211 phy1: U iwl_ht_conf leave
[ 659.022102] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x280E active=2 idle=2
[ 659.022110] ieee80211 phy1: U iwl_bss_info_changed ASSOC 1
[ 659.022121] ieee80211 phy1: U iwl_commit_rxon Sending RXON
[ 659.022124] * without RXON_FILTER_ASSOC_MSK
[ 659.022127] * channel = 40
[ 659.022129] * bssid = 00:02:6f:6e:d7:6c
[ 659.022137] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON
[ 659.022146] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON
[ 659.022157] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_RXON (#10), seq: 0x0403, 54 bytes at 3[3]:4
[ 659.022275] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 659.022414] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON
[ 659.022432] ieee80211 phy1: U iwl_commit_rxon Return from !new_assoc RXON.
[ 659.022439] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode stations in driver
[ 659.022447] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode active for station 0
[ 659.022455] ieee80211 phy1: U iwl_clear_ucode_stations Clearing ucode active for station 15
[ 659.022464] ieee80211 phy1: U iwl_restore_stations Restoring all known stations ... start.
[ 659.022472] ieee80211 phy1: U iwl_restore_stations Restoring sta 00:02:6f:6e:d7:6c
[ 659.022480] ieee80211 phy1: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff
[ 659.022489] ieee80211 phy1: U iwl_send_add_sta Adding sta 0 (00:02:6f:6e:d7:6c) synchronously
[ 659.022498] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA
[ 659.022506] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.022517] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x0404, 96 bytes at 4[4]:4
[ 659.022566] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.022584] ieee80211 phy1: U iwl_process_add_sta_resp Processing response for adding station 0
[ 659.022592] ieee80211 phy1: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 659.022601] ieee80211 phy1: U iwl_sta_ucode_activate Added STA id 0 addr 00:02:6f:6e:d7:6c to uCode
[ 659.022610] ieee80211 phy1: U iwl_process_add_sta_resp Added station id 0 addr 00:02:6f:6e:d7:6c
[ 659.022619] ieee80211 phy1: U iwl_process_add_sta_resp Added station according to cmd buffer 00:02:6f:6e:d7:6c
[ 659.022630] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD
[ 659.022639] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.022651] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x0405, 92 bytes at 5[5]:4
[ 659.022695] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.022718] ieee80211 phy1: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0
[ 659.022729] ieee80211 phy1: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously
[ 659.022737] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA
[ 659.022747] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.022758] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x0406, 96 bytes at 6[6]:4
[ 659.022806] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA
[ 659.022824] ieee80211 phy1: U iwl_process_add_sta_resp Processing response for adding station 15
[ 659.022832] ieee80211 phy1: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 659.022841] ieee80211 phy1: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode
[ 659.022851] ieee80211 phy1: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff
[ 659.022860] ieee80211 phy1: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff
[ 659.022871] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD
[ 659.022880] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.022892] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x0407, 92 bytes at 7[7]:4
[ 659.022935] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD
[ 659.022957] ieee80211 phy1: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15
[ 659.022966] ieee80211 phy1: U iwl_restore_stations Restoring all known stations .... complete.
[ 659.022975] ieee80211 phy1: U iwl_print_rx_config_cmd RX CONFIG:
[ 659.022983] iwl data: 00000000: 00 16 eb 05 61 ea 00 00 00 02 6f 6e d7 6c 00 00 ....a.....on.l..
[ 659.022991] iwl data: 00000010: 00 16 eb 05 61 ea 00 00 03 00 0e 28 15 03 00 00 ....a......(....
[ 659.022999] iwl data: 00000020: 30 80 40 04 04 00 00 00 28 00 ff ff ff 00 00 00 0.@.....(.......
[ 659.023021] iwl data: 00000030: 00 00 ..
[ 659.023029] ieee80211 phy1: U iwl_print_rx_config_cmd u16 channel: 0x28
[ 659.023037] ieee80211 phy1: U iwl_print_rx_config_cmd u32 flags: 0x04408030
[ 659.023044] ieee80211 phy1: U iwl_print_rx_config_cmd u32 filter_flags: 0x00000004
[ 659.023052] ieee80211 phy1: U iwl_print_rx_config_cmd u8 dev_type: 0x3
[ 659.023059] ieee80211 phy1: U iwl_print_rx_config_cmd u8 ofdm_basic_rates: 0x15
[ 659.023067] ieee80211 phy1: U iwl_print_rx_config_cmd u8 cck_basic_rates: 0x03
[ 659.023074] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] node_addr: 00:16:eb:05:61:ea
[ 659.023082] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] bssid_addr: 00:02:6f:6e:d7:6c
[ 659.023090] ieee80211 phy1: U iwl_print_rx_config_cmd u16 assoc_id: 0x0
[ 659.023101] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x0408, 8 bytes at 8[8]:4
[ 659.023113] ieee80211 phy1: U iwl_setup_rxon_timing beacon interval 100 beacon timer 101046 beacon tim 0
[ 659.023122] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING
[ 659.023131] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING
[ 659.023142] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_RXON_TIMING (#14), seq: 0x0409, 24 bytes at 9[9]:4
[ 659.023328] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 659.023352] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING
[ 659.023408] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x280E active=2 idle=2
[ 659.023416] ieee80211 phy1: U iwl_set_rxon_ht rxon flags 0x4408030 operation mode :0x0 extension channel offset 0x3
[ 659.023424] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x280E active=2 idle=2
[ 659.023431] ieee80211 phy1: U iwl_post_associate assoc id 2 beacon interval 100
[ 659.023440] ieee80211 phy1: U iwl_commit_rxon Sending RXON
[ 659.023443] * with RXON_FILTER_ASSOC_MSK
[ 659.023445] * channel = 40
[ 659.023447] * bssid = 00:02:6f:6e:d7:6c
[ 659.023454] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON
[ 659.023461] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON
[ 659.023470] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_RXON (#10), seq: 0x040A, 54 bytes at 10[10]:4
[ 659.023685] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON
[ 659.023727] ieee80211 phy1: U iwl_print_rx_config_cmd RX CONFIG:
[ 659.023737] iwl data: 00000000: 00 16 eb 05 61 ea 00 00 00 02 6f 6e d7 6c 00 00 ....a.....on.l..
[ 659.023746] iwl data: 00000010: 00 16 eb 05 61 ea 00 00 03 00 0e 28 15 03 02 00 ....a......(....
[ 659.023754] iwl data: 00000020: 30 80 40 44 24 00 00 00 28 00 ff ff ff 00 00 00 0.@D$...(.......
[ 659.023762] iwl data: 00000030: 00 00 ..
[ 659.023770] ieee80211 phy1: U iwl_print_rx_config_cmd u16 channel: 0x28
[ 659.023778] ieee80211 phy1: U iwl_print_rx_config_cmd u32 flags: 0x44408030
[ 659.023785] ieee80211 phy1: U iwl_print_rx_config_cmd u32 filter_flags: 0x00000024
[ 659.023793] ieee80211 phy1: U iwl_print_rx_config_cmd u8 dev_type: 0x3
[ 659.023800] ieee80211 phy1: U iwl_print_rx_config_cmd u8 ofdm_basic_rates: 0x15
[ 659.023808] ieee80211 phy1: U iwl_print_rx_config_cmd u8 cck_basic_rates: 0x03
[ 659.023815] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] node_addr: 00:16:eb:05:61:ea
[ 659.023824] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] bssid_addr: 00:02:6f:6e:d7:6c
[ 659.023832] ieee80211 phy1: U iwl_print_rx_config_cmd u16 assoc_id: 0x2
[ 659.023843] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x040B, 8 bytes at 11[11]:4
[ 659.023855] ieee80211 phy1: U iwl_post_associate Associated as 2 to: 00:02:6f:6e:d7:6c
[ 659.023864] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 659.023873] ieee80211 phy1: U iwl_bss_info_changed Changes (0xfd) while associated
[ 659.023881] ieee80211 phy1: U iwlagn_send_rxon_assoc Using current RXON_ASSOC. Not resending.
[ 659.023893] ieee80211 phy1: U iwl_bss_info_changed leave
[ 659.025891] ieee80211 phy1: I iwl_mac_tx enter
[ 659.025906] ieee80211 phy1: I iwl_mac_tx leave
[ 659.026595] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 659.232980] ieee80211 phy1: I iwl_mac_tx enter
[ 659.232998] ieee80211 phy1: I iwl_mac_tx leave
[ 659.235022] ieee80211 phy1: I iwl_mac_tx enter
[ 659.235034] ieee80211 phy1: I iwl_mac_tx leave
[ 659.235343] ieee80211 phy1: I iwl_send_add_sta Adding sta 0 (00:02:6f:6e:d7:6c) asynchronously
[ 659.235358] ieee80211 phy1: I iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x040C, 96 bytes at 12[12]:4
[ 659.235376] ieee80211 phy1: I iwl_mac_tx enter
[ 659.235386] ieee80211 phy1: I iwl_mac_tx leave
[ 659.235664] ieee80211 phy1: I iwl_process_add_sta_resp Processing response for adding station 0
[ 659.235672] ieee80211 phy1: I iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 659.235681] ieee80211 phy1: I iwl_sta_ucode_activate STA id 0 addr 00:02:6f:6e:d7:6c already present in uCode (according to driver)
[ 659.235690] ieee80211 phy1: I iwl_process_add_sta_resp Modified station id 0 addr 00:02:6f:6e:d7:6c
[ 659.235698] ieee80211 phy1: I iwl_process_add_sta_resp Modified station according to cmd buffer 00:02:6f:6e:d8:6c
[ 659.240028] ieee80211 phy1: U iwl_mac_set_key enter
[ 659.240041] ieee80211 phy1: U iwl_send_add_sta Adding sta 0 (00:02:6f:6e:d7:6c) asynchronously
[ 659.240055] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x040D, 96 bytes at 13[13]:4
[ 659.240065] ieee80211 phy1: U iwl_mac_set_key enable hwcrypto key
[ 659.240071] ieee80211 phy1: U iwl_mac_set_key leave
[ 659.240104] ieee80211 phy1: I iwl_process_add_sta_resp Processing response for adding station 0
[ 659.240111] ieee80211 phy1: I iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 659.240119] ieee80211 phy1: I iwl_sta_ucode_activate STA id 0 addr 00:02:6f:6e:d7:6c already present in uCode (according to driver)
[ 659.240128] ieee80211 phy1: I iwl_process_add_sta_resp Modified station id 0 addr 00:02:6f:6e:d7:6c
[ 659.240136] ieee80211 phy1: I iwl_process_add_sta_resp Modified station according to cmd buffer 00:02:6f:6e:d8:6c
[ 659.240189] ieee80211 phy1: U iwl_mac_set_key enter
[ 659.240196] ieee80211 phy1: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) asynchronously
[ 659.240207] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x040E, 96 bytes at 14[14]:4
[ 659.240215] ieee80211 phy1: U iwl_mac_set_key enable hwcrypto key
[ 659.240221] ieee80211 phy1: U iwl_mac_set_key leave
[ 659.240269] ieee80211 phy1: I iwl_process_add_sta_resp Processing response for adding station 15
[ 659.240278] ieee80211 phy1: I iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 659.240286] ieee80211 phy1: I iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver)
[ 659.240296] ieee80211 phy1: I iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff
[ 659.240303] ieee80211 phy1: I iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:00:ff
[ 659.294692] phy1: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 txop=0 uapsd=0
[ 659.294702] ieee80211 phy1: U iwl_mac_conf_tx enter
[ 659.294708] ieee80211 phy1: U iwl_mac_conf_tx leave
[ 659.294717] phy1: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 txop=0 uapsd=0
[ 659.294723] ieee80211 phy1: U iwl_mac_conf_tx enter
[ 659.294728] ieee80211 phy1: U iwl_mac_conf_tx leave
[ 659.294736] phy1: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 txop=94 uapsd=0
[ 659.294743] ieee80211 phy1: U iwl_mac_conf_tx enter
[ 659.294748] ieee80211 phy1: U iwl_mac_conf_tx leave
[ 659.294756] phy1: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 txop=47 uapsd=0
[ 659.294762] ieee80211 phy1: U iwl_mac_conf_tx enter
[ 659.294767] ieee80211 phy1: U iwl_mac_conf_tx leave
[ 659.294774] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x200
[ 659.294788] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_QOS_PARAM (#13), seq: 0x040F, 40 bytes at 15[15]:4
[ 659.294798] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 659.294804] ieee80211 phy1: U iwl_mac_config leave
[ 659.294824] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_QOS_PARAM (0x00000000)
[ 660.113842] ieee80211 phy1: I iwl_enqueue_hcmd Sending command REPLY_LEDS_CMD (#48), seq: 0x0410, 12 bytes at 16[16]:4
[ 660.113903] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_LEDS_CMD (0x00000000)
[ 660.179615] ieee80211 phy1: I iwl_mac_tx enter
[ 660.179635] ieee80211 phy1: I iwl_mac_tx leave
[ 660.225667] ieee80211 phy1: U iwl_configure_filter Enter: changed: 0x0, total: 0x80000000
[ 660.225680] ieee80211 phy1: U iwlagn_send_rxon_assoc Using current RXON_ASSOC. Not resending.
[ 660.225688] ieee80211 phy1: U iwl_print_rx_config_cmd RX CONFIG:
[ 660.225696] iwl data: 00000000: 00 16 eb 05 61 ea 00 00 00 02 6f 6e d7 6c 00 00 ....a.....on.l..
[ 660.225704] iwl data: 00000010: 00 16 eb 05 61 ea 00 00 03 00 0e 28 15 03 02 00 ....a......(....
[ 660.225711] iwl data: 00000020: 30 80 40 44 24 00 00 00 28 00 ff ff ff 00 00 00 0.@D$...(.......
[ 660.225717] iwl data: 00000030: 00 00 ..
[ 660.225724] ieee80211 phy1: U iwl_print_rx_config_cmd u16 channel: 0x28
[ 660.225730] ieee80211 phy1: U iwl_print_rx_config_cmd u32 flags: 0x44408030
[ 660.225737] ieee80211 phy1: U iwl_print_rx_config_cmd u32 filter_flags: 0x00000024
[ 660.225743] ieee80211 phy1: U iwl_print_rx_config_cmd u8 dev_type: 0x3
[ 660.225749] ieee80211 phy1: U iwl_print_rx_config_cmd u8 ofdm_basic_rates: 0x15
[ 660.225756] ieee80211 phy1: U iwl_print_rx_config_cmd u8 cck_basic_rates: 0x03
[ 660.225763] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] node_addr: 00:16:eb:05:61:ea
[ 660.225770] ieee80211 phy1: U iwl_print_rx_config_cmd u8[6] bssid_addr: 00:02:6f:6e:d7:6c
[ 660.225776] ieee80211 phy1: U iwl_print_rx_config_cmd u16 assoc_id: 0x2
[ 660.226343] ieee80211 phy1: I iwl_mac_tx enter
[ 660.226360] ieee80211 phy1: I iwl_mac_tx leave
[ 661.269288] ieee80211 phy1: I iwl_mac_tx enter
[ 661.269295] ieee80211 phy1: I iwl_mac_tx leave
[ 661.270409] ieee80211 phy1: I iwl_mac_tx enter
[ 661.270415] ieee80211 phy1: I iwl_mac_tx leave
[ 661.275458] ieee80211 phy1: I iwl_mac_tx enter
[ 661.275467] ieee80211 phy1: I iwl_mac_tx leave
[ 661.276229] ieee80211 phy1: I iwl_mac_tx enter
[ 661.276235] ieee80211 phy1: I iwl_mac_tx leave
[ 661.277989] ieee80211 phy1: I iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x0411, 92 bytes at 17[17]:4
[ 661.278033] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_LINK_QUALITY_CMD (0x00000000)
[ 661.294079] ieee80211 phy1: I iwl_mac_tx enter
[ 661.294086] ieee80211 phy1: I iwl_mac_tx leave
[ 661.294308] ieee80211 phy1: I iwl_mac_tx enter
[ 661.294312] ieee80211 phy1: I iwl_mac_tx leave
[ 661.299524] ieee80211 phy1: I iwl_mac_tx enter
[ 661.299529] ieee80211 phy1: I iwl_mac_tx leave
[ 661.299681] ieee80211 phy1: I iwl_mac_tx enter
[ 661.299686] ieee80211 phy1: I iwl_mac_tx leave
[ 661.311249] ieee80211 phy1: I iwl_mac_tx enter
[ 661.311266] ieee80211 phy1: I iwl_mac_tx leave
[ 661.311451] ieee80211 phy1: I iwl_mac_tx enter
[ 661.311456] ieee80211 phy1: I iwl_mac_tx leave
[ 661.311616] ieee80211 phy1: I iwl_mac_tx enter
[ 661.311620] ieee80211 phy1: I iwl_mac_tx leave
[ 661.315970] ieee80211 phy1: I iwl_mac_tx enter
[ 661.315976] ieee80211 phy1: I iwl_mac_tx leave
[ 661.316267] ieee80211 phy1: I iwl_mac_tx enter
[ 661.316272] ieee80211 phy1: I iwl_mac_tx leave
[ 661.316414] ieee80211 phy1: I iwl_mac_tx enter
[ 661.316418] ieee80211 phy1: I iwl_mac_tx leave
[ 661.318403] ieee80211 phy1: I iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x0412, 92 bytes at 18[18]:4
[ 661.318444] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_LINK_QUALITY_CMD (0x00000000)
[ 661.334765] ieee80211 phy1: I iwl_mac_tx enter
[ 661.334773] ieee80211 phy1: I iwl_mac_tx leave
[ 661.334807] ieee80211 phy1: I iwl_mac_tx enter
[ 661.334812] ieee80211 phy1: I iwl_mac_tx leave
[ 661.335025] ieee80211 phy1: I iwl_mac_tx enter
[ 661.335031] ieee80211 phy1: I iwl_mac_tx leave
[ 661.335126] ieee80211 phy1: I iwl_mac_tx enter
[ 661.335131] ieee80211 phy1: I iwl_mac_tx leave
[ 661.357142] ieee80211 phy1: I iwl_mac_tx enter
[ 661.357150] ieee80211 phy1: I iwl_mac_tx leave
[ 661.357170] ieee80211 phy1: I iwl_mac_tx enter
[ 661.357175] ieee80211 phy1: I iwl_mac_tx leave
[ 661.357193] ieee80211 phy1: I iwl_mac_tx enter
[ 661.357197] ieee80211 phy1: I iwl_mac_tx leave
[ 661.357214] ieee80211 phy1: I iwl_mac_tx enter
[ 661.357218] ieee80211 phy1: I iwl_mac_tx leave
[ 661.359432] ieee80211 phy1: I iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x0413, 92 bytes at 19[19]:4
[ 661.359497] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_LINK_QUALITY_CMD (0x00000000)
[ 661.375294] ieee80211 phy1: I iwl_mac_tx enter
[ 661.375301] ieee80211 phy1: I iwl_mac_tx leave
[ 661.375323] ieee80211 phy1: I iwl_mac_tx enter
[ 661.375328] ieee80211 phy1: I iwl_mac_tx leave
[ 661.375356] ieee80211 phy1: I iwl_mac_tx enter
[ 661.375360] ieee80211 phy1: I iwl_mac_tx leave
[ 661.375377] ieee80211 phy1: I iwl_mac_tx enter
[ 661.375381] ieee80211 phy1: I iwl_mac_tx leave
[ 661.375850] ieee80211 phy1: I iwl_mac_tx enter
[ 661.375856] ieee80211 phy1: I iwl_mac_tx leave
[ 661.378236] ieee80211 phy1: I iwl_mac_tx enter
[ 661.378242] ieee80211 phy1: I iwl_mac_tx leave
[ 661.552310] ieee80211 phy1: I iwl_mac_tx enter
[ 661.552331] ieee80211 phy1: I iwl_mac_tx leave
[ 665.884005] ieee80211 phy1: I iwl_mac_tx enter
[ 665.884021] ieee80211 phy1: I iwl_mac_tx leave
[ 665.886792] ieee80211 phy1: I iwl_enqueue_hcmd Sending command REPLY_TX_LINK_QUALITY_CMD (#4e), seq: 0x0414, 92 bytes at 20[20]:4
[ 665.887057] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_LINK_QUALITY_CMD (0x00000000)
[ 665.924180] ieee80211 phy1: I iwl_send_add_sta Adding sta 0 (00:02:6f:6e:d7:6c) asynchronously
[ 665.924196] ieee80211 phy1: I iwl_enqueue_hcmd Sending command REPLY_ADD_STA (#18), seq: 0x0415, 96 bytes at 21[21]:4
[ 665.924248] ieee80211 phy1: I iwl_process_add_sta_resp Processing response for adding station 0
[ 665.924255] ieee80211 phy1: I iwl_process_add_sta_resp REPLY_ADD_STA PASSED
[ 665.924263] ieee80211 phy1: I iwl_sta_ucode_activate STA id 0 addr 00:02:6f:6e:d7:6c already present in uCode (according to driver)
[ 665.924272] ieee80211 phy1: I iwl_process_add_sta_resp Modified station id 0 addr 00:02:6f:6e:d7:6c
[ 665.924280] ieee80211 phy1: I iwl_process_add_sta_resp Modified station according to cmd buffer 00:02:6f:6e:d7:6c
[ 668.322093] phy1: Removed STA 00:02:6f:6e:d7:6c
[ 668.322215] phy1: Destroyed STA 00:02:6f:6e:d7:6c
[ 668.322225] wlan0: deauthenticating from 00:02:6f:6e:d7:6c by local choice (reason=3)
[ 668.322300] phy1: device now idle
[ 668.322391] phy1: device no longer idle - scanning
[ 668.324584] phy1: device now idle
[ 668.328446] cfg80211: Calling CRDA to update world regulatory domain
[ 668.328486] cfg80211: Calling CRDA for country: US
[ 668.351238] cfg80211: Regulatory domain changed to country: US
[ 668.351241] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 668.351245] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 668.351248] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 668.351267] (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 668.351270] (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 668.351273] (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 668.351276] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 668.456180] phy1: device no longer idle - scanning
[ 668.456429] wlan0: deauthenticating from 00:02:6f:6e:d7:6c by local choice (reason=3)
[ 668.569218] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 1)
[ 668.769269] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 2)
[ 668.969150] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 3)
[ 669.169262] wlan0: authentication with 00:02:6f:6e:d7:6c timed out
[ 669.169363] phy1: device now idle
[ 679.527920] phy1: device no longer idle - scanning
[ 679.527927] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x100
[ 679.527931] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 679.527934] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 679.527937] ieee80211 phy1: U iwl_mac_config leave
[ 679.527940] ieee80211 phy1: U iwl_mac_hw_scan enter
[ 679.527943] ieee80211 phy1: U iwl_scan_initiate Starting scan...
[ 679.527947] ieee80211 phy1: U iwlagn_request_scan Kicking off active scan
[ 679.527953] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=1 prob=0x3 [ACTIVE 36]
[ 679.527956] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=2 prob=0x3 [ACTIVE 36]
[ 679.527960] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=3 prob=0x3 [ACTIVE 36]
[ 679.527963] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=4 prob=0x3 [ACTIVE 36]
[ 679.527967] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=5 prob=0x3 [ACTIVE 36]
[ 679.527970] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=6 prob=0x3 [ACTIVE 36]
[ 679.527974] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=7 prob=0x3 [ACTIVE 36]
[ 679.527977] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=8 prob=0x3 [ACTIVE 36]
[ 679.527981] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=9 prob=0x3 [ACTIVE 36]
[ 679.527984] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=10 prob=0x3 [ACTIVE 36]
[ 679.527988] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=11 prob=0x3 [ACTIVE 36]
[ 679.527991] ieee80211 phy1: U iwl_get_channels_for_scan total channels to scan 11
[ 679.527994] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD
[ 679.527997] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 679.528003] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_SCAN_CMD (#80), seq: 0x442A, 970 bytes at 42[32]:4
[ 679.530214] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 679.530226] ieee80211 phy1: U iwl_mac_hw_scan leave
[ 679.530931] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 1 [802.11bg] (TSF: 0x00000000:00AAFF82) - 1 (beacon timer 457236606)
[ 679.567833] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 1 [802.11bg] (TSF: 0x00000000:00AB8F8F) - 14 elapsed=36877 usec
[ 679.569694] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 2 [802.11bg] (TSF: 0x00000000:00AB9698) - 1 (beacon timer 457197928)
[ 679.583214] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 2 [802.11bg] (TSF: 0x00000000:00ABCBB9) - 0 elapsed=13601 usec
[ 679.585010] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 3 [802.11bg] (TSF: 0x00000000:00ABD2BE) - 1 (beacon timer 457182530)
[ 679.598806] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 3 [802.11bg] (TSF: 0x00000000:00AC0854) - 1 elapsed=13718 usec
[ 679.600529] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 4 [802.11bg] (TSF: 0x00000000:00AC0F5E) - 1 (beacon timer 461463714)
[ 679.637631] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 4 [802.11bg] (TSF: 0x00000000:00AC9F77) - 1 elapsed=36889 usec
[ 679.639224] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 5 [802.11bg] (TSF: 0x00000000:00ACA681) - 1 (beacon timer 461425023)
[ 679.652717] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 5 [802.11bg] (TSF: 0x00000000:00ACDAEF) - 0 elapsed=13422 usec
[ 679.654439] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 6 [802.11bg] (TSF: 0x00000000:00ACE1F5) - 1 (beacon timer 461409803)
[ 679.699401] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 6 [802.11bg] (TSF: 0x00000000:00AD9193) - 9 elapsed=44958 usec
[ 679.701197] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 7 [802.11bg] (TSF: 0x00000000:00AD989A) - 1 (beacon timer 465659750)
[ 679.738077] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 7 [802.11bg] (TSF: 0x00000000:00AE28A4) - 4 elapsed=36874 usec
[ 679.739874] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 8 [802.11bg] (TSF: 0x00000000:00AE2FAA) - 1 (beacon timer 465621078)
[ 679.752172] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 8 [802.11bg] (TSF: 0x00000000:00AE5FB2) - 1 elapsed=12296 usec
[ 679.753971] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 9 [802.11bg] (TSF: 0x00000000:00AE66B8) - 1 (beacon timer 465606984)
[ 679.766196] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 9 [802.11bg] (TSF: 0x00000000:00AE9676) - 0 elapsed=12222 usec
[ 679.768220] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 10 [802.11bg] (TSF: 0x00000000:00AE9D7D) - 1 (beacon timer 465592963)
[ 679.806505] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 10 [802.11bg] (TSF: 0x00000000:00AF33F1) - 2 elapsed=38516 usec
[ 679.808304] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 11 [802.11bg] (TSF: 0x00000000:00AF3AF9) - 1 (beacon timer 469849351)
[ 679.845277] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 11 [802.11bg] (TSF: 0x00000000:00AFCB0C) - 11 elapsed=36883 usec
[ 679.847041] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan complete: 11 channels (TSF 0x00AFD242:00000000) - 1
[ 679.847068] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan on 2.4GHz took 320ms
[ 679.847075] ieee80211 phy1: I iwl_rx_scan_complete_notif Setting scan to off
[ 679.847096] ieee80211 phy1: U iwl_bg_scan_completed SCAN complete scan
[ 679.847120] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x042B, 8 bytes at 43[11]:4
[ 679.847151] ieee80211 phy1: U iwl_mac_hw_scan enter
[ 679.847161] ieee80211 phy1: U iwl_scan_initiate Starting scan...
[ 679.847171] ieee80211 phy1: U iwlagn_request_scan Kicking off active scan
[ 679.847184] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=36 prob=0x2 [PASSIVE 110]
[ 679.847194] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=40 prob=0x2 [PASSIVE 110]
[ 679.847204] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=44 prob=0x2 [PASSIVE 110]
[ 679.847214] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=48 prob=0x2 [PASSIVE 110]
[ 679.847223] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=52 prob=0x2 [PASSIVE 110]
[ 679.847233] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=56 prob=0x2 [PASSIVE 110]
[ 679.847243] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=60 prob=0x2 [PASSIVE 110]
[ 679.847252] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=64 prob=0x2 [PASSIVE 110]
[ 679.847281] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=100 prob=0x2 [PASSIVE 110]
[ 679.847292] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=104 prob=0x2 [PASSIVE 110]
[ 679.847301] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=108 prob=0x2 [PASSIVE 110]
[ 679.847311] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=112 prob=0x2 [PASSIVE 110]
[ 679.847321] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=116 prob=0x2 [PASSIVE 110]
[ 679.847331] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=132 prob=0x2 [PASSIVE 110]
[ 679.847349] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 679.847363] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=136 prob=0x2 [PASSIVE 110]
[ 679.847373] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=140 prob=0x2 [PASSIVE 110]
[ 679.847383] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=149 prob=0x2 [PASSIVE 110]
[ 679.847393] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=153 prob=0x2 [PASSIVE 110]
[ 679.847403] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=157 prob=0x2 [PASSIVE 110]
[ 679.847412] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=161 prob=0x2 [PASSIVE 110]
[ 679.847422] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=165 prob=0x2 [PASSIVE 110]
[ 679.847431] ieee80211 phy1: U iwl_get_channels_for_scan total channels to scan 21
[ 679.847439] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD
[ 679.847448] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 679.847461] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_SCAN_CMD (#80), seq: 0x442C, 1084 bytes at 44[32]:4
[ 679.849409] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 679.849428] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 36 [802.11a] (TSF: 0x00000000:00AFDB7A) - 1 (beacon timer 469808262)
[ 679.849450] ieee80211 phy1: U iwl_mac_hw_scan leave
[ 679.962076] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 36 [802.11a] (TSF: 0x00000000:00B1939D) - 0 elapsed=112675 usec
[ 679.963906] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 40 [802.11a] (TSF: 0x00000000:00B19AC1) - 1 (beacon timer 473990463)
[ 680.076586] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 40 [802.11a] (TSF: 0x00000000:00B352E4) - 0 elapsed=112675 usec
[ 680.078399] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 44 [802.11a] (TSF: 0x00000000:00B35A09) - 1 (beacon timer 478172663)
[ 680.191118] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 44 [802.11a] (TSF: 0x00000000:00B51230) - 0 elapsed=112679 usec
[ 680.193127] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 48 [802.11a] (TSF: 0x00000000:00B51955) - 1 (beacon timer 482354859)
[ 680.229922] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 48 [802.11a] (TSF: 0x00000000:00B5A999) - 20 elapsed=36932 usec
[ 680.231745] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 52 [802.11a] (TSF: 0x00000000:00B5B0BE) - 1 (beacon timer 486612802)
[ 680.344563] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 52 [802.11a] (TSF: 0x00000000:00B768E4) - 0 elapsed=112678 usec
[ 680.346264] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 56 [802.11a] (TSF: 0x00000000:00B77009) - 1 (beacon timer 490794999)
[ 680.376952] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 56 [802.11a] (TSF: 0x00000000:00B7E768) - 2 elapsed=30559 usec
[ 680.378567] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 60 [802.11a] (TSF: 0x00000000:00B7EE8B) - 1 (beacon timer 490762613)
[ 680.491284] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 60 [802.11a] (TSF: 0x00000000:00B9A6B1) - 0 elapsed=112678 usec
[ 680.493077] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 64 [802.11a] (TSF: 0x00000000:00B9ADD4) - 1 (beacon timer 494944812)
[ 680.520644] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 64 [802.11a] (TSF: 0x00000000:00BA1971) - 11 elapsed=27549 usec
[ 680.522449] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 100 [802.11a] (TSF: 0x00000000:00BA2093) - 1 (beacon timer 499212141)
[ 680.635159] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 100 [802.11a] (TSF: 0x00000000:00BBD8BC) - 0 elapsed=112681 usec
[ 680.636958] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 104 [802.11a] (TSF: 0x00000000:00BBDFDC) - 1 (beacon timer 503394340)
[ 680.749845] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 104 [802.11a] (TSF: 0x00000000:00BD9808) - 0 elapsed=112684 usec
[ 680.751471] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 108 [802.11a] (TSF: 0x00000000:00BD9F29) - 1 (beacon timer 507576535)
[ 680.864360] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 108 [802.11a] (TSF: 0x00000000:00BF5754) - 0 elapsed=112683 usec
[ 680.865983] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 112 [802.11a] (TSF: 0x00000000:00BF5E74) - 1 (beacon timer 511758732)
[ 680.978754] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 112 [802.11a] (TSF: 0x00000000:00C1169E) - 0 elapsed=112682 usec
[ 680.980504] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 116 [802.11a] (TSF: 0x00000000:00C11DBE) - 1 (beacon timer 515940930)
[ 681.093193] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 116 [802.11a] (TSF: 0x00000000:00C2D5E8) - 0 elapsed=112682 usec
[ 681.095001] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 132 [802.11a] (TSF: 0x00000000:00C2DD08) - 1 (beacon timer 520123128)
[ 681.207886] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 132 [802.11a] (TSF: 0x00000000:00C49538) - 0 elapsed=112688 usec
[ 681.209508] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 136 [802.11a] (TSF: 0x00000000:00C49C5E) - 1 (beacon timer 524305314)
[ 681.322400] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 136 [802.11a] (TSF: 0x00000000:00C65488) - 0 elapsed=112682 usec
[ 681.324024] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 140 [802.11a] (TSF: 0x00000000:00C65BAB) - 1 (beacon timer 528487509)
[ 681.436706] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 140 [802.11a] (TSF: 0x00000000:00C813D5) - 0 elapsed=112682 usec
[ 681.438521] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 149 [802.11a] (TSF: 0x00000000:00C81AF4) - 1 (beacon timer 536966412)
[ 681.468084] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 149 [802.11a] (TSF: 0x00000000:00C88E1A) - 13 elapsed=29478 usec
[ 681.469844] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 153 [802.11a] (TSF: 0x00000000:00C8953A) - 1 (beacon timer 536935110)
[ 681.583073] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 153 [802.11a] (TSF: 0x00000000:00CA4F3F) - 2 elapsed=113157 usec
[ 681.584810] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 157 [802.11a] (TSF: 0x00000000:00CA565C) - 1 (beacon timer 541116835)
[ 681.697518] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 157 [802.11a] (TSF: 0x00000000:00CC0E8B) - 0 elapsed=112687 usec
[ 681.699321] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 161 [802.11a] (TSF: 0x00000000:00CC15A8) - 1 (beacon timer 545299032)
[ 681.732435] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 161 [802.11a] (TSF: 0x00000000:00CC96F2) - 6 elapsed=33098 usec
[ 681.734236] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 165 [802.11a] (TSF: 0x00000000:00CC9E14) - 1 (beacon timer 545264108)
[ 681.847150] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 165 [802.11a] (TSF: 0x00000000:00CE5655) - 0 elapsed=112705 usec
[ 681.848856] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan complete: 21 channels (TSF 0x00CE5D8C:00000000) - 1
[ 681.848866] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan on 5.2GHz took 2001ms
[ 681.848873] ieee80211 phy1: I iwl_rx_scan_complete_notif Setting scan to off
[ 681.848913] ieee80211 phy1: U iwl_bg_scan_completed SCAN complete scan
[ 681.848931] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x40
[ 681.848941] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x240E active=2 idle=1
[ 681.848952] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 681.848958] ieee80211 phy1: U iwl_mac_config leave
[ 681.848964] phy1: device now idle
[ 681.848971] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x100
[ 681.848978] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 681.848986] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 681.848991] ieee80211 phy1: U iwl_mac_config leave
[ 681.849039] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x042D, 8 bytes at 45[13]:4
[ 681.849273] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 686.855593] phy1: device no longer idle - scanning
[ 686.855608] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x100
[ 686.855617] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 686.855625] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 686.855631] ieee80211 phy1: U iwl_mac_config leave
[ 686.855639] ieee80211 phy1: U iwl_mac_hw_scan enter
[ 686.855645] ieee80211 phy1: U iwl_scan_initiate Starting scan...
[ 686.855655] ieee80211 phy1: U iwlagn_request_scan Kicking off active scan
[ 686.855666] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=1 prob=0x1 [ACTIVE 33]
[ 686.855675] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=2 prob=0x1 [ACTIVE 33]
[ 686.855683] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=3 prob=0x1 [ACTIVE 33]
[ 686.855691] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=4 prob=0x1 [ACTIVE 33]
[ 686.855699] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=5 prob=0x1 [ACTIVE 33]
[ 686.855707] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=6 prob=0x1 [ACTIVE 33]
[ 686.855715] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=7 prob=0x1 [ACTIVE 33]
[ 686.855723] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=8 prob=0x1 [ACTIVE 33]
[ 686.855731] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=9 prob=0x1 [ACTIVE 33]
[ 686.855739] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=10 prob=0x1 [ACTIVE 33]
[ 686.855749] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=11 prob=0x1 [ACTIVE 33]
[ 686.855756] ieee80211 phy1: U iwl_get_channels_for_scan total channels to scan 11
[ 686.855764] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD
[ 686.855771] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 686.855784] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_SCAN_CMD (#80), seq: 0x442E, 970 bytes at 46[32]:4
[ 686.857993] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 686.858037] ieee80211 phy1: U iwl_mac_hw_scan leave
[ 686.858720] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 1 [802.11bg] (TSF: 0x00000000:011ACF72) - 1 (beacon timer 754974862)
[ 686.896193] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 1 [802.11bg] (TSF: 0x00000000:011B618C) - 12 elapsed=37402 usec
[ 686.897924] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 2 [802.11bg] (TSF: 0x00000000:011B6892) - 1 (beacon timer 759232366)
[ 686.909926] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 2 [802.11bg] (TSF: 0x00000000:011B9761) - 1 elapsed=11983 usec
[ 686.911701] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 3 [802.11bg] (TSF: 0x00000000:011B9E66) - 1 (beacon timer 759218586)
[ 686.923268] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 3 [802.11bg] (TSF: 0x00000000:011BCAC0) - 1 elapsed=11354 usec
[ 686.924865] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 4 [802.11bg] (TSF: 0x00000000:011BD1C6) - 1 (beacon timer 759205434)
[ 686.937014] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 4 [802.11bg] (TSF: 0x00000000:011C012D) - 1 elapsed=12135 usec
[ 686.938801] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 5 [802.11bg] (TSF: 0x00000000:011C0833) - 1 (beacon timer 759191501)
[ 686.972792] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 5 [802.11bg] (TSF: 0x00000000:011C8C3D) - 1 elapsed=33802 usec
[ 686.974393] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 6 [802.11bg] (TSF: 0x00000000:011C9344) - 1 (beacon timer 763452604)
[ 687.011967] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 6 [802.11bg] (TSF: 0x00000000:011D2612) - 10 elapsed=37582 usec
[ 687.013766] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 7 [802.11bg] (TSF: 0x00000000:011D2D18) - 1 (beacon timer 763413224)
[ 687.047781] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 7 [802.11bg] (TSF: 0x00000000:011DB11D) - 6 elapsed=33797 usec
[ 687.049365] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 8 [802.11bg] (TSF: 0x00000000:011DB823) - 1 (beacon timer 763377629)
[ 687.060817] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 8 [802.11bg] (TSF: 0x00000000:011DE412) - 0 elapsed=11247 usec
[ 687.062436] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 9 [802.11bg] (TSF: 0x00000000:011DEB18) - 1 (beacon timer 763364584)
[ 687.073610] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 9 [802.11bg] (TSF: 0x00000000:011E16D4) - 1 elapsed=11196 usec
[ 687.075408] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 10 [802.11bg] (TSF: 0x00000000:011E1DDB) - 1 (beacon timer 767648293)
[ 687.087373] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 10 [802.11bg] (TSF: 0x00000000:011E4C4C) - 1 elapsed=11889 usec
[ 687.089090] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 11 [802.11bg] (TSF: 0x00000000:011E5353) - 1 (beacon timer 767634605)
[ 687.122991] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 11 [802.11bg] (TSF: 0x00000000:011ED768) - 6 elapsed=33813 usec
[ 687.124753] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan complete: 11 channels (TSF 0x011EDE9E:00000000) - 1
[ 687.124764] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan on 2.4GHz took 269ms
[ 687.124770] ieee80211 phy1: I iwl_rx_scan_complete_notif Setting scan to off
[ 687.124792] ieee80211 phy1: U iwl_bg_scan_completed SCAN complete scan
[ 687.124817] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x042F, 8 bytes at 47[15]:4
[ 687.124827] ieee80211 phy1: U iwl_mac_hw_scan enter
[ 687.124835] ieee80211 phy1: U iwl_scan_initiate Starting scan...
[ 687.124844] ieee80211 phy1: U iwlagn_request_scan Kicking off active scan
[ 687.124856] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=36 prob=0x0 [PASSIVE 110]
[ 687.124865] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=40 prob=0x0 [PASSIVE 110]
[ 687.124874] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=44 prob=0x0 [PASSIVE 110]
[ 687.124882] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=48 prob=0x0 [PASSIVE 110]
[ 687.124890] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=52 prob=0x0 [PASSIVE 110]
[ 687.124898] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=56 prob=0x0 [PASSIVE 110]
[ 687.124906] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=60 prob=0x0 [PASSIVE 110]
[ 687.124914] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=64 prob=0x0 [PASSIVE 110]
[ 687.124923] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=100 prob=0x0 [PASSIVE 110]
[ 687.124931] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=104 prob=0x0 [PASSIVE 110]
[ 687.124939] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=108 prob=0x0 [PASSIVE 110]
[ 687.124947] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=112 prob=0x0 [PASSIVE 110]
[ 687.124956] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=116 prob=0x0 [PASSIVE 110]
[ 687.124964] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=132 prob=0x0 [PASSIVE 110]
[ 687.124972] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=136 prob=0x0 [PASSIVE 110]
[ 687.124980] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=140 prob=0x0 [PASSIVE 110]
[ 687.124989] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=149 prob=0x0 [PASSIVE 110]
[ 687.124997] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=153 prob=0x0 [PASSIVE 110]
[ 687.125005] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=157 prob=0x0 [PASSIVE 110]
[ 687.125013] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=161 prob=0x0 [PASSIVE 110]
[ 687.125022] ieee80211 phy1: U iwl_get_channels_for_scan Scanning ch=165 prob=0x0 [PASSIVE 110]
[ 687.125029] ieee80211 phy1: U iwl_get_channels_for_scan total channels to scan 21
[ 687.125046] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 687.125058] ieee80211 phy1: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD
[ 687.125066] ieee80211 phy1: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 687.125080] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_SCAN_CMD (#80), seq: 0x4430, 1084 bytes at 48[32]:4
[ 687.127081] ieee80211 phy1: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD
[ 687.127100] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 36 [802.11a] (TSF: 0x00000000:011EE76B) - 1 (beacon timer 767596693)
[ 687.127129] ieee80211 phy1: U iwl_mac_hw_scan leave
[ 687.239682] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 36 [802.11a] (TSF: 0x00000000:01209F8E) - 0 elapsed=112675 usec
[ 687.241509] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 40 [802.11a] (TSF: 0x00000000:0120A6B2) - 1 (beacon timer 771778894)
[ 687.354257] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 40 [802.11a] (TSF: 0x00000000:01225ED9) - 0 elapsed=112679 usec
[ 687.356039] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 44 [802.11a] (TSF: 0x00000000:012265FE) - 1 (beacon timer 775961090)
[ 687.468909] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 44 [802.11a] (TSF: 0x00000000:01241E25) - 0 elapsed=112679 usec
[ 687.470558] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 48 [802.11a] (TSF: 0x00000000:0124254A) - 1 (beacon timer 780143286)
[ 687.508591] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 48 [802.11a] (TSF: 0x00000000:0124B9A9) - 22 elapsed=37983 usec
[ 687.510346] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 52 [802.11a] (TSF: 0x00000000:0124C0D1) - 1 (beacon timer 784400175)
[ 687.623104] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 52 [802.11a] (TSF: 0x00000000:012678F4) - 0 elapsed=112675 usec
[ 687.624858] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 56 [802.11a] (TSF: 0x00000000:01268019) - 1 (beacon timer 788582374)
[ 687.747668] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 56 [802.11a] (TSF: 0x00000000:01285F85) - 2 elapsed=122732 usec
[ 687.749413] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 60 [802.11a] (TSF: 0x00000000:012866A8) - 1 (beacon timer 792754519)
[ 687.862317] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 60 [802.11a] (TSF: 0x00000000:012A1EE2) - 0 elapsed=112698 usec
[ 687.864018] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 64 [802.11a] (TSF: 0x00000000:012A2609) - 1 (beacon timer 796936695)
[ 687.914655] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 64 [802.11a] (TSF: 0x00000000:012AEC1C) - 7 elapsed=50707 usec
[ 687.916563] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 100 [802.11a] (TSF: 0x00000000:012AF344) - 1 (beacon timer 801180860)
[ 688.029141] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 100 [802.11a] (TSF: 0x00000000:012CAB67) - 0 elapsed=112675 usec
[ 688.030962] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 104 [802.11a] (TSF: 0x00000000:012CB28C) - 1 (beacon timer 805363060)
[ 688.143650] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 104 [802.11a] (TSF: 0x00000000:012E6AB3) - 0 elapsed=112679 usec
[ 688.145477] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 108 [802.11a] (TSF: 0x00000000:012E71DB) - 1 (beacon timer 809545253)
[ 688.258259] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 108 [802.11a] (TSF: 0x00000000:013029FF) - 0 elapsed=112676 usec
[ 688.260083] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 112 [802.11a] (TSF: 0x00000000:01303125) - 1 (beacon timer 813727451)
[ 688.372891] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 112 [802.11a] (TSF: 0x00000000:0131E949) - 0 elapsed=112676 usec
[ 688.374592] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 116 [802.11a] (TSF: 0x00000000:0131F06F) - 1 (beacon timer 817909649)
[ 688.487250] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 116 [802.11a] (TSF: 0x00000000:0133A893) - 0 elapsed=112676 usec
[ 688.489037] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 132 [802.11a] (TSF: 0x00000000:0133AFC0) - 1 (beacon timer 822091840)
[ 688.601809] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 132 [802.11a] (TSF: 0x00000000:013567F7) - 0 elapsed=112695 usec
[ 688.603636] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 136 [802.11a] (TSF: 0x00000000:01356F20) - 1 (beacon timer 830570720)
[ 688.716337] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 136 [802.11a] (TSF: 0x00000000:0137275B) - 0 elapsed=112699 usec
[ 688.718087] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 140 [802.11a] (TSF: 0x00000000:01372E7F) - 1 (beacon timer 834752897)
[ 688.830989] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 140 [802.11a] (TSF: 0x00000000:0138E6BC) - 0 elapsed=112701 usec
[ 688.832689] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 149 [802.11a] (TSF: 0x00000000:0138EDDE) - 1 (beacon timer 838935074)
[ 688.858599] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 149 [802.11a] (TSF: 0x00000000:0139529E) - 14 elapsed=25792 usec
[ 688.860227] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 153 [802.11a] (TSF: 0x00000000:013959C2) - 1 (beacon timer 838907454)
[ 688.972996] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 153 [802.11a] (TSF: 0x00000000:013B11EA) - 0 elapsed=112680 usec
[ 688.974740] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 157 [802.11a] (TSF: 0x00000000:013B1910) - 1 (beacon timer 843089648)
[ 689.087507] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 157 [802.11a] (TSF: 0x00000000:013CD136) - 0 elapsed=112678 usec
[ 689.089328] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 161 [802.11a] (TSF: 0x00000000:013CD85B) - 1 (beacon timer 847271845)
[ 689.133926] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 161 [802.11a] (TSF: 0x00000000:013D86E1) - 8 elapsed=44678 usec
[ 689.135829] ieee80211 phy1: I iwl_rx_scan_start_notif Scan start: 165 [802.11a] (TSF: 0x00000000:013D8E05) - 1 (beacon timer 851522043)
[ 689.248643] ieee80211 phy1: I iwl_rx_scan_results_notif Scan ch.res: 165 [802.11a] (TSF: 0x00000000:013F4630) - 0 elapsed=112683 usec
[ 689.250270] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan complete: 21 channels (TSF 0x013F4D63:00000000) - 1
[ 689.250279] ieee80211 phy1: I iwl_rx_scan_complete_notif Scan on 5.2GHz took 2126ms
[ 689.250286] ieee80211 phy1: I iwl_rx_scan_complete_notif Setting scan to off
[ 689.250309] ieee80211 phy1: U iwl_bg_scan_completed SCAN complete scan
[ 689.250327] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x40
[ 689.250336] ieee80211 phy1: U iwl_set_rxon_chain rx_chain=0x240E active=2 idle=1
[ 689.250347] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 689.250353] ieee80211 phy1: U iwl_mac_config leave
[ 689.250360] phy1: device now idle
[ 689.250366] ieee80211 phy1: U iwl_mac_config enter to channel 40 changed 0x100
[ 689.250373] ieee80211 phy1: U iwl_power_sleep_cam_cmd Sleep command for CAM
[ 689.250380] ieee80211 phy1: U iwl_mac_config Not re-sending same RXON configuration.
[ 689.250386] ieee80211 phy1: U iwl_mac_config leave
[ 689.250407] ieee80211 phy1: U iwl_enqueue_hcmd Sending command REPLY_TX_POWER_DBM_CMD (#95), seq: 0x0431, 8 bytes at 49[17]:4
[ 689.250888] ieee80211 phy1: I iwl_generic_cmd_callback back from REPLY_TX_POWER_DBM_CMD (0x00000000)
[ 697.693280] phy1: device no longer idle - scanning
[ 697.739250] wlan0: authenticate with 00:02:6f:6e:d7:68 (try 1)
[ 697.742567] wlan0: authenticated
[ 697.742586] phy1: device now idle
[ 697.746369] phy1: device no longer idle - working
[ 697.748621] wlan0: associate with 00:02:6f:6e:d7:68 (try 1)
[ 697.755062] wlan0: RX AssocResp from 00:02:6f:6e:d7:68 (capab=0xc31 status=0 aid=1)
[ 697.755066] wlan0: associated
[ 697.755071] phy1: Allocated STA 00:02:6f:6e:d7:68
[ 697.755229] phy1: Inserted STA 00:02:6f:6e:d7:68
[ 697.828185] phy1: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 txop=0 uapsd=0
[ 697.828197] phy1: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 txop=0 uapsd=0
[ 697.828207] phy1: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 txop=94 uapsd=0
[ 697.828215] phy1: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 txop=47 uapsd=0
[ 768.616236] iwlagn 0000:03:00.0: Aggregation not enabled for tid 0 because load = 0
^ permalink raw reply
* Re: [PATCH v2 00/20] native support for wl1271 on ZOOM
From: John W. Linville @ 2010-07-26 19:30 UTC (permalink / raw)
To: Ohad Ben-Cohen
Cc: linux-wireless, linux-mmc, linux-omap, linux-arm-kernel, linux,
Chikkature Rajashekar Madhusudhan, Luciano Coelho, akpm,
San Mehat, Roger Quadros, Tony Lindgren, Nicolas Pitre,
Pandita Vikram, Kalle Valo
In-Reply-To: <1279733634-21974-1-git-send-email-ohad@wizery.com>
On Wed, Jul 21, 2010 at 08:33:34PM +0300, Ohad Ben-Cohen wrote:
> This patch series adds native support for wl1271 on ZOOM.
Just for the record, I'm fine with the wl1271 bits here going through
the omap tree with the rest of the series.
John
--
John W. Linville Someday the world will need a hero, and you
linville@tuxdriver.com might be all we have. Be ready.
^ permalink raw reply
* Re: [ath9k-devel] [RFC] ath9k: improve aggregation throughput by using only first rate
From: Felix Fietkau @ 2010-07-26 19:41 UTC (permalink / raw)
To: Björn Smedman; +Cc: ath9k-devel, linux-wireless
In-Reply-To: <AANLkTinZ=KDo4aJU6Z93p1DXghF_MzE9CeBN6OuC_LnD@mail.gmail.com>
On 2010-07-26 9:23 PM, Björn Smedman wrote:
> 2010/7/26 Felix Fietkau <nbd@openwrt.org>:
>> On 2010-07-26 7:10 PM, Björn Smedman wrote:
>>> I think there are some (in theory) simple improvements that can be
>>> done to the tx aggregation / rate control logic. A proof of concept of
>>> one such improvement is provided below. Basically, it's a hack that
>> I think it makes sense to rely less on on-chip MRR for fallback, but I
>> think to make this workable, we really should use the MRR table for
>> something, otherwise the rate control algorithm will take much longer to
>> adapt.
>> It's probably better to fix this properly after I'm done with my A-MPDU
>> rewrite, because then I can more easily push parts of the software
>> retransmission behaviour into minstrel_ht directly.
>
> Sounds very reasonable. I'm sure you've thought of it but now that
> it's fresh in my head it would be great if the new aggregation design
> allowed us to experiment with stuff like this:
>
> * The rate control logic treats the average aggregate length as a
> measured independent variable, when in fact it depends heavily on the
> rates selected (via the 4 ms txop limit).
Yes, with the new design maybe we could use the initial rate lookup only
for setting the sampling flag, and then doing a separate per-AMPDU
lookup, which properly takes the AMPDU length into account.
> * When tx is aggregated most rate control probe frames end up inside
> aggregates and are never used for probing (effective probe frequency
> is divided by average aggregate length).
Nope, a probing frame never ends up inside an aggregate. It's always
sent out as a single frame, which is why I had to make the decision
about sending a probing frame more complex in minstrel_ht, compared to
minstrel - the previous 10% stuff was limiting aggregation size.
> * When setting up a hardware MRR for an aggregate the focus should be
> on throughput (as explained earlier in this thread). But there are
> situations when reliability is important: e.g. when a subframe in the
> aggregate is about to expire (because of time or block ack window). It
> may even be advantageous to tx the subframes that are about to expire
> in their own aggregate with lower / more reliable bitrate?
Yes, that's what I was thinking as well. We should probably make this
decision based on the number of sw-retransmitted frames, and maybe
consider the offset of seqno vs baw_tail as well.
> * In many busy radio environments the packet success rate depends very
> much on the protection method being used (none, cts-to-self or
> rts-cts), often more so than on the bitrate itself. It would be
> interesting to experiment with including the protection method in the
> rate selection, i.e. to probe for the optimal protection method and
> bitrate combination.
Sounds good.
> * In order to have the best possible rate control in very dynamic rf
> environments it's important to keep the hardware queue short and
> select rates as late as possible (to not introduce unnecessary delay
> when selecting new rates). I have no idea how to do this but it would
> be great if the tx queue could be kept long enough to never stall tx,
> but no longer.
This would work with what I suggested above - per-AMPDU rate lookup.
With software scheduling that's easy to do, since we already restrict
the queue to max. 2 AMPDUs
> * If I understand correctly the Atheros hardware does not adjust the
> rts / cts-to-self duration field when going through the MRR
> (correct?). In that case it may be even more advantageous to use
> software retry as much as possible when some form of protection is
> enabled.
Not sure, but I think it does adjust the duration field according to the
rate, while transmitting.
> Looking forward to the new aggregation code!
That will still take some time, I recently came up with some better
design ideas, which require some larger changes to the code that I
already wrote.
- Felix
^ permalink raw reply
* Re: [ath9k-devel] [RFC] ath9k: improve aggregation throughput by using only first rate
From: Björn Smedman @ 2010-07-26 19:23 UTC (permalink / raw)
To: Felix Fietkau; +Cc: ath9k-devel, linux-wireless
In-Reply-To: <4C4DC98E.6090002@openwrt.org>
2010/7/26 Felix Fietkau <nbd@openwrt.org>:
> On 2010-07-26 7:10 PM, Björn Smedman wrote:
>> I think there are some (in theory) simple improvements that can be
>> done to the tx aggregation / rate control logic. A proof of concept of
>> one such improvement is provided below. Basically, it's a hack that
> I think it makes sense to rely less on on-chip MRR for fallback, but I
> think to make this workable, we really should use the MRR table for
> something, otherwise the rate control algorithm will take much longer to
> adapt.
> It's probably better to fix this properly after I'm done with my A-MPDU
> rewrite, because then I can more easily push parts of the software
> retransmission behaviour into minstrel_ht directly.
Sounds very reasonable. I'm sure you've thought of it but now that
it's fresh in my head it would be great if the new aggregation design
allowed us to experiment with stuff like this:
* The rate control logic treats the average aggregate length as a
measured independent variable, when in fact it depends heavily on the
rates selected (via the 4 ms txop limit).
* When tx is aggregated most rate control probe frames end up inside
aggregates and are never used for probing (effective probe frequency
is divided by average aggregate length).
* When setting up a hardware MRR for an aggregate the focus should be
on throughput (as explained earlier in this thread). But there are
situations when reliability is important: e.g. when a subframe in the
aggregate is about to expire (because of time or block ack window). It
may even be advantageous to tx the subframes that are about to expire
in their own aggregate with lower / more reliable bitrate?
* In many busy radio environments the packet success rate depends very
much on the protection method being used (none, cts-to-self or
rts-cts), often more so than on the bitrate itself. It would be
interesting to experiment with including the protection method in the
rate selection, i.e. to probe for the optimal protection method and
bitrate combination.
* In order to have the best possible rate control in very dynamic rf
environments it's important to keep the hardware queue short and
select rates as late as possible (to not introduce unnecessary delay
when selecting new rates). I have no idea how to do this but it would
be great if the tx queue could be kept long enough to never stall tx,
but no longer.
* If I understand correctly the Atheros hardware does not adjust the
rts / cts-to-self duration field when going through the MRR
(correct?). In that case it may be even more advantageous to use
software retry as much as possible when some form of protection is
enabled.
Looking forward to the new aggregation code!
/Björn
^ permalink raw reply
* [PATCH] iwlagn: use __packed on new structure definitions
From: John W. Linville @ 2010-07-26 19:12 UTC (permalink / raw)
To: linux-wireless; +Cc: wey-yi.w.guy, John W. Linville
"iwlagn: add statistic notification structure for WiFi/BT devices" added
several new '__attribute__ ((packed))' lines. Change them to the
generic __packed.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
drivers/net/wireless/iwlwifi/iwl-commands.h | 12 ++++++------
1 files changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/iwlwifi/iwl-commands.h b/drivers/net/wireless/iwlwifi/iwl-commands.h
index 798bf9e..9c44ab5 100644
--- a/drivers/net/wireless/iwlwifi/iwl-commands.h
+++ b/drivers/net/wireless/iwlwifi/iwl-commands.h
@@ -3132,7 +3132,7 @@ struct statistics_rx_non_phy_bt {
/* additional stats for bt */
__le32 num_bt_kills;
__le32 reserved[2];
-} __attribute__ ((packed));
+} __packed;
struct statistics_rx {
struct statistics_rx_phy ofdm;
@@ -3146,7 +3146,7 @@ struct statistics_rx_bt {
struct statistics_rx_phy cck;
struct statistics_rx_non_phy_bt general;
struct statistics_rx_ht_phy ofdm_ht;
-} __attribute__ ((packed));
+} __packed;
/**
* struct statistics_tx_power - current tx power
@@ -3226,7 +3226,7 @@ struct statistics_general_common {
* in order to get out of bad PHY status
*/
__le32 num_of_sos_states;
-} __attribute__ ((packed));
+} __packed;
struct statistics_bt_activity {
/* Tx statistics */
@@ -3239,13 +3239,13 @@ struct statistics_bt_activity {
__le32 hi_priority_rx_denied_cnt;
__le32 lo_priority_rx_req_cnt;
__le32 lo_priority_rx_denied_cnt;
-} __attribute__ ((packed));
+} __packed;
struct statistics_general {
struct statistics_general_common common;
__le32 reserved2;
__le32 reserved3;
-} __attribute__ ((packed));
+} __packed;
struct statistics_general_bt {
struct statistics_general_common common;
@@ -3316,7 +3316,7 @@ struct iwl_bt_notif_statistics {
struct statistics_rx_bt rx;
struct statistics_tx tx;
struct statistics_general_bt general;
-} __attribute__ ((packed));
+} __packed;
/*
* MISSED_BEACONS_NOTIFICATION = 0xa2 (notification only, not a command)
--
1.7.1.1
^ permalink raw reply related
* iwlagn: two regressions 2.6.34->2.6.35-rc6
From: Andrew Lutomirski @ 2010-07-26 19:08 UTC (permalink / raw)
To: linux-wireless, ilw
Regression 1: I got a SYSASSERT. rmmod/modprobe fixed it. No fancy
debug because I can't reproduce it.
[ 167.648419] phy0: device no longer idle - scanning
[ 167.656408] phy0: device now idle
[ 167.715946] phy0: device no longer idle - scanning
[ 167.716066] iwlagn 0000:03:00.0: Microcode SW error detected.
Restarting 0x82000000.
[ 167.716069] iwlagn 0000:03:00.0: Loaded firmware version: 8.24.2.12
[ 167.716105] iwlagn 0000:03:00.0: Start IWL Error Log Dump:
[ 167.716108] iwlagn 0000:03:00.0: Status: 0x0002B2E4, count: 5
[ 167.716302] iwlagn 0000:03:00.0: Desc
Time data1 data2 line
[ 167.716307] iwlagn 0000:03:00.0: SYSASSERT (#05)
1042449688 0x00200200 0x00000000 1051
[ 167.716312] iwlagn 0000:03:00.0: pc blink1 blink2 ilink1 ilink2 hcmd
[ 167.716316] iwlagn 0000:03:00.0: 0x02CC8 0x02C98 0x02C98 0x008B2
0x00000 0x441C0080
[ 167.716319] iwlagn 0000:03:00.0: CSR values:
[ 167.716322] iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is
CSR_INT_PERIODIC_REG)
[ 167.716350] iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480301
[ 167.716376] iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X00000040
[ 167.716401] iwlagn 0000:03:00.0: CSR_INT: 0X00000000
[ 167.716409] iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000
[ 167.716418] iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000
[ 167.716426] iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000008
[ 167.716435] iwlagn 0000:03:00.0: CSR_RESET: 0X00000000
[ 167.716444] iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5
[ 167.716452] iwlagn 0000:03:00.0: CSR_HW_REV: 0X00000024
[ 167.716461] iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X00000000
[ 167.716470] iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000804
[ 167.716478] iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00060000
[ 167.716487] iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080042
[ 167.716495] iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X00002183
[ 167.716504] iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000
[ 167.716529] iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000
[ 167.716537] iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000
[ 167.716563] iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000058
[ 167.716588] iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88135b6a
[ 167.716614] iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200
[ 167.716639] iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00880300
[ 167.716664] iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a
[ 167.716673] iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0000
[ 167.716675] iwlagn 0000:03:00.0: FH register values:
[ 167.716710] iwlagn 0000:03:00.0:
FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X133cf500
[ 167.716730] iwlagn 0000:03:00.0:
FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X01339760
[ 167.716750] iwlagn 0000:03:00.0:
FH_RSCSR_CHNL0_WPTR: 0X00000098
[ 167.716770] iwlagn 0000:03:00.0:
FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104
[ 167.716789] iwlagn 0000:03:00.0:
FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc
[ 167.716808] iwlagn 0000:03:00.0:
FH_MEM_RSSR_RX_STATUS_REG: 0X07030000
[ 167.716827] iwlagn 0000:03:00.0:
FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
[ 167.716846] iwlagn 0000:03:00.0:
FH_TSSR_TX_STATUS_REG: 0X07ff0001
[ 167.716865] iwlagn 0000:03:00.0:
FH_TSSR_TX_ERROR_REG: 0X00000000
[ 167.716922] iwlagn 0000:03:00.0: Start IWL Event Log Dump: display
last 20 entries
[ 167.716944] iwlagn 0000:03:00.0: EVT_LOGT:0151076484:0x00000037:0353
[ 167.716975] iwlagn 0000:03:00.0: EVT_LOGT:0151076880:0x0000010f:0106
[ 167.717006] iwlagn 0000:03:00.0: EVT_LOGT:0151076881:0x00000000:0302
[ 167.717037] iwlagn 0000:03:00.0: EVT_LOGT:0151076905:0x00000038:0353
[ 167.717051] iwlagn 0000:03:00.0: EVT_LOGT:0151077567:0x441c0080:0401
[ 167.717066] iwlagn 0000:03:00.0: EVT_LOGT:0151077568:0x441c0080:0700
[ 167.717080] iwlagn 0000:03:00.0: EVT_LOGT:0151077569:0x00000000:0706
[ 167.717094] iwlagn 0000:03:00.0: EVT_LOGT:0151077585:0x00000001:0452
[ 167.717109] iwlagn 0000:03:00.0: EVT_LOGT:0151077587:0x00000001:0452
[ 167.717139] iwlagn 0000:03:00.0: EVT_LOGT:0151077588:0x00000233:0601
[ 167.717153] iwlagn 0000:03:00.0: EVT_LOGT:0151077589:0x00000061:0600
[ 167.717168] iwlagn 0000:03:00.0: EVT_LOGT:0151077591:0x0000007a:0602
[ 167.717182] iwlagn 0000:03:00.0: EVT_LOGT:0151077597:0x00000100:0706
[ 167.717213] iwlagn 0000:03:00.0: EVT_LOGT:0151077601:0x00000000:0708
[ 167.717227] iwlagn 0000:03:00.0: EVT_LOGT:0151077603:0x01000200:0706
[ 167.717258] iwlagn 0000:03:00.0: EVT_LOGT:0151077613:0x01000200:0725
[ 167.717263] iwlagn 0000:03:00.0: EVT_LOGT:0151077613:0x00000000:0709
[ 167.717263] iwlagn 0000:03:00.0: EVT_LOGT:0151077614:0x00000000:0707
[ 167.717263] iwlagn 0000:03:00.0: EVT_LOGT:0151077614:0x02000201:0706
[ 167.717263] iwlagn 0000:03:00.0: EVT_LOGT:0151077622:0x00000000:0125
Regression 2:
On 2.6.34 my wireless appears to be rock solid (yay -- it's been awhile).
On 2.6.35-rc6, I have an AP here that doesn't work well. It's an
EnGenius ESR-7750 with latest firmware. I can connect to its 2.4GHz
radio (usually but it seems to connect more slowly than 2.6.34), but I
can't always see the 5GHz radio, let alone connect. It's connected
exactly once out of many tries on 2.6.35-rc6, but it works fine on
2.6.34.
In the attached log, you'll see the one successful connection to
00:02:6f:6e:d7:6c as well as a failure. The failure is just:
[ 668.569218] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 1)
[ 668.769269] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 2)
[ 668.969150] wlan0: authenticate with 00:02:6f:6e:d7:6c (try 3)
[ 669.169262] wlan0: authentication with 00:02:6f:6e:d7:6c timed out
--Andy
^ permalink raw reply
* Compat-wireless release for 2010-07-26 is baked
From: Compat-wireless cronjob account @ 2010-07-26 19:04 UTC (permalink / raw)
To: linux-wireless
>From git://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next
f435fa7..d40de6c history -> origin/history
+ 80e9579...f0fbdf0 master -> origin/master (forced update)
b37fa16..86c65a7 stable -> origin/stable
* [new tag] next-20100726 -> next-20100726
compat-wireless code metrics
493710 - Total upstream lines of code being pulled
1447 - backport code changes
1211 - backport code additions
236 - backport code deletions
5764 - backport from compat module
7211 - total backport code
1.4606 - % of code consists of backport work
1218 - Crap changes not yet posted
1179 - Crap additions not yet posted
39 - Crap deletions not yet posted
0.2467 - % of crap code
Base tree: linux-next.git
Base tree version: next-20100726
compat-wireless release: compat-wireless-2010-07-13-4-g04898a5
^ permalink raw reply
* Re: [PATCH] ath5k: disable ASPM
From: John W. Linville @ 2010-07-26 18:37 UTC (permalink / raw)
To: Maxim Levitsky
Cc: Jussi Kivilinna, ath5k-devel, linux-wireless, Luis R. Rodriguez
In-Reply-To: <1280162044.3492.14.camel@maxim-laptop>
On Mon, Jul 26, 2010 at 07:34:04PM +0300, Maxim Levitsky wrote:
> Just want to summarize and finally put that problem to rest.
>
> Was the patch that removes & sets on CONFIG_PCIEASPM? accepted?
>
> Is it possible to check that all ath5k pcie devices that must not use
> L0s actually have the 'PCI_EXP_DEVCAP_RBER' disabled (this bit causes
> pcie device be marked as legacy, and ASPM is disabled on it)
http://marc.info/?l=linux-wireless&m=127507083106814&w=2
"Sorry, I meant to this to be RFC patch."
So, I dropped it.
John
--
John W. Linville Someday the world will need a hero, and you
linville@tuxdriver.com might be all we have. Be ready.
^ permalink raw reply
* Re: [ath5k-devel] [PATCH] ath5k: disable ASPM
From: Luis R. Rodriguez @ 2010-07-26 18:41 UTC (permalink / raw)
To: Maxim Levitsky
Cc: Jussi Kivilinna, Luis R. Rodriguez, ath5k-devel, linux-wireless,
David Quan
In-Reply-To: <1280162044.3492.14.camel@maxim-laptop>
On Mon, Jul 26, 2010 at 9:34 AM, Maxim Levitsky <maximlevitsky@gmail.com> wrote:
> Hi,
>
> Just want to summarize and finally put that problem to rest.
>
> Was the patch that removes & sets on CONFIG_PCIEASPM? accepted?
>
> Is it possible to check that all ath5k pcie devices that must not use
> L0s actually have the 'PCI_EXP_DEVCAP_RBER' disabled (this bit causes
> pcie device be marked as legacy, and ASPM is disabled on it)
ASPM should be kept enabled for ath5k but L0s should be disabled, so
that is, only L1 for ASPM should be kept enabled for ath5k for all
ath5k chipsets. Can someone resubmit the simpler patch again on a new
independent thread?
Luis
^ permalink raw reply
* RE: [PATCH v2 19/20] omap: zoom: keep the MMC3 wl1271 device powered off
From: Gabay, Benzy @ 2010-07-26 18:33 UTC (permalink / raw)
To: Ohad Ben-Cohen
Cc: linux-wireless@vger.kernel.org, linux-mmc@vger.kernel.org,
linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux@arm.linux.org.uk, Chikkature Rajashekar, Madhusudhan,
Luciano Coelho, akpm@linux-foundation.org, San Mehat,
Roger Quadros, Tony Lindgren, Nicolas Pitre, Pandita, Vikram,
Kalle Valo
In-Reply-To: <AANLkTim3RWv2-qi9UMg1imwKTJuh3GstdjMTxz64uOHf@mail.gmail.com>
Ohad,
> -----Original Message-----
> From: Ohad Ben-Cohen [mailto:ohad@wizery.com]
> Sent: Thursday, July 22, 2010 6:18 PM
> To: Gabay, Benzy
> Cc: linux-wireless@vger.kernel.org; linux-mmc@vger.kernel.org; linux-
> omap@vger.kernel.org; linux-arm-kernel@lists.infradead.org;
> linux@arm.linux.org.uk; Chikkature Rajashekar, Madhusudhan; Luciano
> Coelho; akpm@linux-foundation.org; San Mehat; Roger Quadros; Tony
> Lindgren; Nicolas Pitre; Pandita, Vikram; Kalle Valo
> Subject: Re: [PATCH v2 19/20] omap: zoom: keep the MMC3 wl1271 device
> powered off
>
> Hi Gever,
>
> On Wed, Jul 21, 2010 at 9:55 PM, Gabay, Benzy <benzyg@ti.com> wrote:
> > From: Ohad Ben-Cohen [mailto:ohad@wizery.com]
> > Sent: Wednesday, July 21, 2010 12:34 PM
> > To: linux-wireless@vger.kernel.org; linux-mmc@vger.kernel.org; linux-
> omap@vger.kernel.org
> > Cc: linux-arm-kernel@lists.infradead.org; linux@arm.linux.org.uk;
> Chikkature Rajashekar, Madhusudhan; Luciano Coelho; akpm@linux-
> foundation.org; San Mehat; Roger Quadros; Tony Lindgren; Nicolas Pitre;
> Pandita, Vikram; Kalle Valo; Ohad Ben-Cohen
> > Subject: [PATCH v2 19/20] omap: zoom: keep the MMC3 wl1271 device
> powered off
> >
> > Keep the MMC3 wl1271 WLAN device powered off until its
> > SDIO function driver requests otherwise.
> >
> > Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
> > ---
> > arch/arm/mach-omap2/board-zoom-peripherals.c | 1 +
> > arch/arm/mach-omap2/hsmmc.c | 3 +++
> > arch/arm/mach-omap2/hsmmc.h | 1 +
> > arch/arm/plat-omap/include/plat/mmc.h | 3 +++
> > drivers/mmc/host/omap_hsmmc.c | 3 +++
> > 5 files changed, 11 insertions(+), 0 deletions(-)
> >
> > diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c
> b/arch/arm/mach-omap2/board-zoom-peripherals.c
> > index 3230801..3ab9125 100644
> > --- a/arch/arm/mach-omap2/board-zoom-peripherals.c
> > +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c
> > @@ -217,6 +217,7 @@ static struct omap2_hsmmc_info mmc[] __initdata =
> {
> > .gpio_wp = -EINVAL,
> > .gpio_cd = -EINVAL,
> > .ocr_mask = MMC_VDD_165_195,
> > + .dont_power_card = true,
> > .priv_data = &omap_zoom_wlan_data,
> > },
> > {} /* Terminator */
> ...
> > --
> > 1.7.0.4
> >
> > [Benzy Gabay] small comment: Please make sure that all 127x related
> changes are not bounded only to MMC3.
> > On OMAP4 WLAN is used on MMC5.
>
>
> The only place MMC3 is bound is in the board files (see code snippet
> above), so that should be ok.
>
> I can probably split this patch to make this more obvious just by
> reading the diffstat if you prefer.
Yep. That will be great.
Benzy
>
>
> Thanks,
> Ohad.
>
>
> >
^ permalink raw reply
* Re: [PATCH 4/5] wireless: use newly introduced hex_to_bin()
From: John W. Linville @ 2010-07-26 18:27 UTC (permalink / raw)
To: Andy Shevchenko
Cc: David S. Miller, netdev, linux-kernel, Corey Thomas,
linux-wireless
In-Reply-To: <9d7821ff7791c30772667681c0eab829e6e93e59.1279890832.git.andy.shevchenko@gmail.com>
On Fri, Jul 23, 2010 at 04:18:09PM +0300, Andy Shevchenko wrote:
> Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
> Cc: Corey Thomas <coreythomas@charter.net>
> Cc: "John W. Linville" <linville@tuxdriver.com>
> Cc: linux-wireless@vger.kernel.org
Acked-by: John W. Linville <linville@tuxdriver.com>
--
John W. Linville Someday the world will need a hero, and you
linville@tuxdriver.com might be all we have. Be ready.
^ permalink raw reply
* Re: Atheros 0cf3:b003
From: Luis R. Rodriguez @ 2010-07-26 18:29 UTC (permalink / raw)
To: sergi; +Cc: linux-wireless, Stephen Chen
In-Reply-To: <AANLkTin7cn_TgEeepaWrE4sTuu5YxqPNDTDs-hxCs0vC@mail.gmail.com>
On Mon, Jul 26, 2010 at 11:29 AM, Luis R. Rodriguez <mcgrof@gmail.com> wrote:
> On Sat, Jul 24, 2010 at 1:04 AM, sergi <sergitfe1974@gmail.com> wrote:
>> Luis R. Rodriguez <mcgrof@...> writes:
>>
>>>
>>> 2010/7/23 Maximi89 <maximi89@...>:
>>> > Hola Luis, conoces ese ID?, Atheros 0cf3:b003
>>> > Es efectivamente un AR9271?
>>>
>>> No, cual tarjeta es esa? Las que tenemos son estos:
>>>
>>
>>> { },
>>> };
>>>
>>> Stephen, have you heard of 0cf3:b003 as an ar9271 or HB94 card?
>>>
>>> Luis
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
>>> the body of a message to majordomo@...
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>
>>> Hola Luis yo fui quien le mando la consulta a maximiliano,,mi lapiz usb es de
>> la casa Ubiquiti modelo wifistation ext y ahi dicen k tiene el atheros 9271..y
>> el id k me sale es el mencionado,,tanto en Mac,Linux y con Everest en win,uso
>> Ubuntu Ultimate 2.7 con kernel 2.6.32-24 y nada k no me funciona,Podria cmbiar
>> el Id para k sea compatible?? ..bueno muchas gracias por tu atencion
>
> Can you please share your Windows driver INF file ?
Forgot to CC Stephen, please include him in your replies.
Luis
^ permalink raw reply
* Re: Atheros 0cf3:b003
From: Luis R. Rodriguez @ 2010-07-26 18:29 UTC (permalink / raw)
To: sergi; +Cc: linux-wireless
In-Reply-To: <loom.20100724T095719-176@post.gmane.org>
On Sat, Jul 24, 2010 at 1:04 AM, sergi <sergitfe1974@gmail.com> wrote:
> Luis R. Rodriguez <mcgrof@...> writes:
>
>>
>> 2010/7/23 Maximi89 <maximi89@...>:
>> > Hola Luis, conoces ese ID?, Atheros 0cf3:b003
>> > Es efectivamente un AR9271?
>>
>> No, cual tarjeta es esa? Las que tenemos son estos:
>>
>
>> { },
>> };
>>
>> Stephen, have you heard of 0cf3:b003 as an ar9271 or HB94 card?
>>
>> Luis
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
>> the body of a message to majordomo@...
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>> Hola Luis yo fui quien le mando la consulta a maximiliano,,mi lapiz usb es de
> la casa Ubiquiti modelo wifistation ext y ahi dicen k tiene el atheros 9271..y
> el id k me sale es el mencionado,,tanto en Mac,Linux y con Everest en win,uso
> Ubuntu Ultimate 2.7 con kernel 2.6.32-24 y nada k no me funciona,Podria cmbiar
> el Id para k sea compatible?? ..bueno muchas gracias por tu atencion
Can you please share your Windows driver INF file ?
Luis
^ permalink raw reply
* Re: linux-wireless compile broken
From: Ben Greear @ 2010-07-26 18:01 UTC (permalink / raw)
To: John W. Linville; +Cc: linux-wireless
In-Reply-To: <20100726174902.GD3903@tuxdriver.com>
On 07/26/2010 10:49 AM, John W. Linville wrote:
> On Mon, Jul 26, 2010 at 10:31:05AM -0700, Ben Greear wrote:
> Cc: John W. Linville<linville@tuxdriver.com>
> Signed-off-by: Greg Kroah-Hartman<gregkh@suse.de>
>
> You should probably just turn-off that driver in your .config.
> Anyway, I normally recommend that people use wireless-testing for
> actual development.
Ok, I'll dig up wireless-testing.
Thanks,
Ben
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply
* Re: linux-wireless compile broken
From: John W. Linville @ 2010-07-26 17:49 UTC (permalink / raw)
To: Ben Greear; +Cc: linux-wireless
In-Reply-To: <4C4DC659.7090006@candelatech.com>
On Mon, Jul 26, 2010 at 10:31:05AM -0700, Ben Greear wrote:
> Pulled and attempted to build linux-wireless this morning:
>
> [greearb@build-32 linux-wireless.p4s]$ make bzImage modules
> make -C /home/greearb/git/wireless-2.6 O=/home/greearb/kernel/2.6/linux-wireless.p4s/. bzImage modules
> Using /home/greearb/git/wireless-2.6 as source for kernel
> GEN /home/greearb/kernel/2.6/linux-wireless.p4s/Makefile
> CHK include/linux/version.h
> CHK include/generated/utsrelease.h
> CALL /home/greearb/git/wireless-2.6/scripts/checksyscalls.sh
> CHK include/generated/compile.h
> LD drivers/staging/built-in.o
> CC [M] drivers/staging/netwave/netwave_cs.o
> /home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:250: error: expected specifier-qualifier-list before ‘dev_node_t’
> /home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c: In function ‘netwave_snapshot’:
> /home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:291: error: ‘netwave_private’ has no member named ‘lastExec’
> /home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:302: error: implicit declaration of function ‘copy_from_pc’
> /home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:302: error: ‘netwave_private’ has no member named ‘nss’
> /home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c: In function ‘netwave_get_wireless_stats’:
> /home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:318: error: ‘netwave_private’ has no member named ‘ramBase’
wireless-2.6 doesn't have this:
commit e5b3e80016198ee55c82dfd653c1dee99a38964b
Author: Greg Kroah-Hartman <gregkh@suse.de>
Date: Wed May 5 23:17:29 2010 -0700
Staging: netwave: delete the driver
It has sat in the staging directory since October of 2009, and no one
has stepped up to take it over, so odds are, no one cares about it
anymore. So, it is now deleted as scheduled, and documented in the TODO
file.
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
You should probably just turn-off that driver in your .config.
Anyway, I normally recommend that people use wireless-testing for
actual development.
John
--
John W. Linville Someday the world will need a hero, and you
linville@tuxdriver.com might be all we have. Be ready.
^ permalink raw reply
* Re: [ath9k-devel] [RFC] ath9k: improve aggregation throughput by using only first rate
From: Felix Fietkau @ 2010-07-26 17:44 UTC (permalink / raw)
To: Björn Smedman; +Cc: ath9k-devel, linux-wireless
In-Reply-To: <AANLkTimWoSTAtb0m9V=0CNowhy=KtpiKj-O3vdmV8qxB@mail.gmail.com>
On 2010-07-26 7:10 PM, Björn Smedman wrote:
> Hi all,
>
> I've been running a lot of iperf on AR913x /
> compat-wireless-2010-07-16 (w/ openwrt/trunk@22388).
>
> I think there are some (in theory) simple improvements that can be
> done to the tx aggregation / rate control logic. A proof of concept of
> one such improvement is provided below. Basically, it's a hack that
> makes ath9k output aggregates with only the first rate in the rate
> series. The reasoning is that a failure is not a problem for
> aggregates because there is software retry. Retrying in hardware at a
> slower rate is counter productive. So, better to fail and do a
> software retry at possibly another rate. Also, since the aggregate
> size is often limited by the slowest rate in the MRR series (4 ms txop
> limit) having a slow rate in the series may affect performance even if
> it is never used by the hardware.
>
> In my (not so scientific) tests max AP downstream throughput increases
> about 30-40% with the patch below (from 33.9 to 55.7 Mbit/s with HT20
> in noisy environment with 20 meters and a few walls between AP and
> client).
>
> Of course, if all rates in the series are high then this patch has no effect.
I think it makes sense to rely less on on-chip MRR for fallback, but I
think to make this workable, we really should use the MRR table for
something, otherwise the rate control algorithm will take much longer to
adapt.
It's probably better to fix this properly after I'm done with my A-MPDU
rewrite, because then I can more easily push parts of the software
retransmission behaviour into minstrel_ht directly.
- Felix
^ permalink raw reply
* linux-wireless compile broken
From: Ben Greear @ 2010-07-26 17:31 UTC (permalink / raw)
To: linux-wireless
Pulled and attempted to build linux-wireless this morning:
[greearb@build-32 linux-wireless.p4s]$ make bzImage modules
make -C /home/greearb/git/wireless-2.6 O=/home/greearb/kernel/2.6/linux-wireless.p4s/. bzImage modules
Using /home/greearb/git/wireless-2.6 as source for kernel
GEN /home/greearb/kernel/2.6/linux-wireless.p4s/Makefile
CHK include/linux/version.h
CHK include/generated/utsrelease.h
CALL /home/greearb/git/wireless-2.6/scripts/checksyscalls.sh
CHK include/generated/compile.h
LD drivers/staging/built-in.o
CC [M] drivers/staging/netwave/netwave_cs.o
/home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:250: error: expected specifier-qualifier-list before ‘dev_node_t’
/home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c: In function ‘netwave_snapshot’:
/home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:291: error: ‘netwave_private’ has no member named ‘lastExec’
/home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:302: error: implicit declaration of function ‘copy_from_pc’
/home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:302: error: ‘netwave_private’ has no member named ‘nss’
/home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c: In function ‘netwave_get_wireless_stats’:
/home/greearb/git/wireless-2.6/drivers/staging/netwave/netwave_cs.c:318: error: ‘netwave_private’ has no member named ‘ramBase’
Thanks,
Ben
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
^ permalink raw reply
* Re: iw dev wlan0 link - "Not connected"
From: Luis R. Rodriguez @ 2010-07-26 17:23 UTC (permalink / raw)
To: Zhongliang Zhao; +Cc: linux-wireless
In-Reply-To: <4C4D5560.2040201@iam.unibe.ch>
On Mon, Jul 26, 2010 at 2:29 AM, Zhongliang Zhao <zhao@iam.unibe.ch> wrote:
> Dear all,
>
> When I use "iw dev wlan0 link" to get information on wlan0 (basically to
> check the channel used on wlan0),
> it says: " Not connected "
>
> Can someone tell me how to fix this?
Refer to:
http://wireless.kernel.org/en/users/Documentation/iw#Getting_link_status
And then:
http://wireless.kernel.org/en/users/Documentation/iw#Establishing_a_basic_connection
What you really want to use is:
http://wireless.kernel.org/en/users/Documentation/wpa_supplicant
Luis
^ permalink raw reply
* Re: BUG at arch/x86/mm/physaddr.c:5
From: Felix Fietkau @ 2010-07-26 17:22 UTC (permalink / raw)
To: Luis R. Rodriguez
Cc: Jike Song, Ortwin Glück, linux-kernel,
Vasanthakumar Thiagarajan, jmalinen, Sujith.Manoharan,
senthilkumar, linux-wireless, John W. Linville
In-Reply-To: <AANLkTi=Ga2Sy60=wXKQT3nv_PRYw-og7279bD9LTWENE@mail.gmail.com>
On 2010-07-26 6:55 PM, Luis R. Rodriguez wrote:
> 2010/7/25 Jike Song <albcamus@gmail.com>:
>> 2010/7/23 Ortwin Glück <odi@odi.ch>:
>>> On 23.07.2010 10:04, Jike Song wrote:
>>>> Seems to be a logical error? Does the following patch remove your Oops?
>>>
>>> Looking at the init code I agree. Yes, the patch fixes the OOPS. I am sure
>>> because the OOPS occurred at every boot and now it's gone.
>>>
>>> Thanks!
>>>
>>> Ortwin
>>
>> Hi Maintainers,
>>
>> Since Ortwin has confirmed this patch , would you give me an ACK/NAK please?
>>
> I'll let Felix chime in on this one as he last reviewed this path.
> There were some serious issues with MIPs and DMA that at this point I
> think only he grocked.
A patch exactly like that was already posted and merged into the
wireless-testing tree a while ago, it apparently just hasn't made it to
Linus' tree. John, could we get this one into 2.6.35?
http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commitdiff;h=56824223ac97ca845652c59bed9ce139e100261b
commit 56824223ac97ca845652c59bed9ce139e100261b
Author: Ming Lei <tom.leiming@gmail.com>
Date: Fri May 14 21:15:38 2010 +0800
ath9k: fix dma direction for map/unmap in ath_rx_tasklet
For edma, we should use DMA_BIDIRECTIONAL, or else use
DMA_FROM_DEVICE.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
^ permalink raw reply
* [RFC] ath9k: improve aggregation throughput by using only first rate
From: Björn Smedman @ 2010-07-26 17:10 UTC (permalink / raw)
To: ath9k-devel, linux-wireless
Hi all,
I've been running a lot of iperf on AR913x /
compat-wireless-2010-07-16 (w/ openwrt/trunk@22388).
I think there are some (in theory) simple improvements that can be
done to the tx aggregation / rate control logic. A proof of concept of
one such improvement is provided below. Basically, it's a hack that
makes ath9k output aggregates with only the first rate in the rate
series. The reasoning is that a failure is not a problem for
aggregates because there is software retry. Retrying in hardware at a
slower rate is counter productive. So, better to fail and do a
software retry at possibly another rate. Also, since the aggregate
size is often limited by the slowest rate in the MRR series (4 ms txop
limit) having a slow rate in the series may affect performance even if
it is never used by the hardware.
In my (not so scientific) tests max AP downstream throughput increases
about 30-40% with the patch below (from 33.9 to 55.7 Mbit/s with HT20
in noisy environment with 20 meters and a few walls between AP and
client).
Of course, if all rates in the series are high then this patch has no effect.
/Björn
---
diff -urpN a/drivers/net/wireless/ath/ath9k/xmit.c
b/drivers/net/wireless/ath/ath9k/xmit.c
--- a/drivers/net/wireless/ath/ath9k/xmit.c 2010-07-26 15:35:17.000000000 +0200
+++ b/drivers/net/wireless/ath/ath9k/xmit.c 2010-07-26 17:11:33.000000000 +0200
@@ -565,7 +565,7 @@ static u32 ath_lookup_rate(struct ath_so
*/
max_4ms_framelen = ATH_AMPDU_LIMIT_MAX;
- for (i = 0; i < 4; i++) {
+ for (i = 0; i < 1; i++) {
if (rates[i].count) {
int modeidx;
if (!(rates[i].flags & IEEE80211_TX_RC_MCS)) {
@@ -1553,6 +1553,9 @@ static void ath_buf_set_rate(struct ath_
if (sc->sc_flags & SC_OP_PREAMBLE_SHORT)
ctsrate |= rate->hw_value_short;
+ if (bf_isaggr(bf))
+ rates[1].count = rates[2].count = rates[3].count = 0;
+
for (i = 0; i < 4; i++) {
bool is_40, is_sgi, is_sp;
int phy;
^ permalink raw reply
* Re: BUG at arch/x86/mm/physaddr.c:5
From: Luis R. Rodriguez @ 2010-07-26 16:55 UTC (permalink / raw)
To: Jike Song
Cc: Ortwin Glück, linux-kernel, Felix Fietkau,
Vasanthakumar Thiagarajan, jmalinen, Sujith.Manoharan,
senthilkumar, linux-wireless
In-Reply-To: <AANLkTikrmM0pwBLLMWTCO-stRnoCxwQf0M3ZByc7=8_b@mail.gmail.com>
2010/7/25 Jike Song <albcamus@gmail.com>:
> 2010/7/23 Ortwin Glück <odi@odi.ch>:
>> On 23.07.2010 10:04, Jike Song wrote:
>>> Seems to be a logical error? Does the following patch remove your Oops?
>>
>> Looking at the init code I agree. Yes, the patch fixes the OOPS. I am sure
>> because the OOPS occurred at every boot and now it's gone.
>>
>> Thanks!
>>
>> Ortwin
>
> Hi Maintainers,
>
> Since Ortwin has confirmed this patch , would you give me an ACK/NAK please?
>
>
> --
> Thanks,
> Jike
>
>
> From 1414829dcc5b53ef4802f5de2b9be58e2ca0fb23 Mon Sep 17 00:00:00 2001
> From: Jike Song <albcamus@gmail.com>
> Date: Mon, 26 Jul 2010 13:42:41 +0800
> Subject: [PATCH] ath9k: fix wrong DMA direction in RX tasklet
> MIME-Version: 1.0
> Content-Type: text/plain; charset=utf-8
> Content-Transfer-Encoding: 8bit
>
> Commit b5c80475abaad015699384ca64ef8229fdd88758 introduced edma
> support for RX, hence bidirectional DMA support. But it
> specified the DMA type as DMA_FROM_DEVICE by mistake.
>
> Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
> Signed-off-by: Jike Song <albcamus@gmail.com>
> ---
> drivers/net/wireless/ath/ath9k/recv.c | 4 ++--
> 1 files changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/wireless/ath/ath9k/recv.c
> b/drivers/net/wireless/ath/ath9k/recv.c
> index ca6065b..e3e5291 100644
> --- a/drivers/net/wireless/ath/ath9k/recv.c
> +++ b/drivers/net/wireless/ath/ath9k/recv.c
> @@ -844,9 +844,9 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush, bool hp)
> int dma_type;
>
> if (edma)
> - dma_type = DMA_FROM_DEVICE;
> - else
> dma_type = DMA_BIDIRECTIONAL;
> + else
> + dma_type = DMA_FROM_DEVICE;
>
> qtype = hp ? ATH9K_RX_QUEUE_HP : ATH9K_RX_QUEUE_LP;
> spin_lock_bh(&sc->rx.rxbuflock);
> --
I'll let Felix chime in on this one as he last reviewed this path.
There were some serious issues with MIPs and DMA that at this point I
think only he grocked.
Luis
^ permalink raw reply
* Re: [PATCH] ath5k: disable ASPM
From: Maxim Levitsky @ 2010-07-26 16:34 UTC (permalink / raw)
To: Jussi Kivilinna; +Cc: ath5k-devel, linux-wireless, Luis R. Rodriguez
In-Reply-To: <20100528100901.14580.1322.stgit@fate.lan>
Hi,
Just want to summarize and finally put that problem to rest.
Was the patch that removes & sets on CONFIG_PCIEASPM? accepted?
Is it possible to check that all ath5k pcie devices that must not use
L0s actually have the 'PCI_EXP_DEVCAP_RBER' disabled (this bit causes
pcie device be marked as legacy, and ASPM is disabled on it)
Best regards,
Maxim Levitsky
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox