* Re: Problem bringing up wlan0 interface up with mainline wl1271 drivers
From: Elvis Dowson @ 2010-12-17 10:25 UTC (permalink / raw)
To: Arik Nemtsov
Cc: panduranga, Ohad Ben-Cohen, Linux Wireless Mailing List,
Jara, Pedro
In-Reply-To: <AANLkTikvk+AqKRr1VbKv9pSHicy7PAGu8GkdeZuvYwFh@mail.gmail.com>
Hi Arik,
On Dec 17, 2010, at 2:12 PM, Arik Nemtsov wrote:
>
> The firmware file should be called wl1271-fw.bin and the nvs file
> should be called wl1271-nvs.bin. Both should reside in /etc/firmware
> (if you're running a standard linux).
I got the files from this git repo
git clone git://git.kernel.org/pub/scm/linux/kernel/git/dwmw2/linux-firmware.git
and copied them over to /etc/firmware
/etc/firmware# ls -l
total 276
-r--r--r-- 1 root root 271712 Dec 17 2010 wl1271-fw.bin
-rw-rw-r-- 1 root root 912 Dec 17 2010 wl1271-nvs.bin
But I still get a error saying the the nvs file could not be found:
[ 63.852264] wl1271: ERROR could not get nvs file: -2
[ 63.906250] wl1271: loaded
[ 63.909271] wl1271: initialized
Best regards,
Elvis Dowson
^ permalink raw reply
* Re: Problem bringing up wlan0 interface up with mainline wl1271 drivers
From: Arik Nemtsov @ 2010-12-17 10:12 UTC (permalink / raw)
To: Elvis Dowson
Cc: panduranga, Ohad Ben-Cohen, Linux Wireless Mailing List,
Jara, Pedro
In-Reply-To: <C4B3622F-ADC4-481E-9340-1819C815184A@mac.com>
On Fri, Dec 17, 2010 at 11:44, Elvis Dowson <elvis.dowson@mac.com> wrote:
>
> On Dec 17, 2010, at 12:51 PM, Arik Nemtsov wrote:
>
>> Ethernet addresses with the LSB of the first octet turned on are considered multicast addresses. Please try:
>>
>> ifconfig wlan0 hw ether 00:22:33:44:55:66
>
> That worked, now the only thing is to put the firmware file in the appropriate place, I guess:
>
> # ifconfig wlan0 hw ether 00:22:33:44:55:66
>
> # ifconfig wlan0 up
>
> [ 153.843597] wl1271: ERROR could not get firmware: -2
>
> Where should the firmware file be located? /etc/firmware ?
>
> Elvis Dowson
>
The firmware file should be called wl1271-fw.bin and the nvs file
should be called wl1271-nvs.bin. Both should reside in /etc/firmware
(if you're running a standard linux).
Regards,
Arik
^ permalink raw reply
* Re: [RFT] rtlwifi: use alloc_workqueue
From: Tejun Heo @ 2010-12-17 9:57 UTC (permalink / raw)
To: Larry Finger; +Cc: John W. Linville, linux-wireless
In-Reply-To: <4D0ADCBC.1000300@lwfinger.net>
Hello,
On 12/17/2010 04:45 AM, Larry Finger wrote:
> On 12/16/2010 01:59 PM, John W. Linville wrote:
>> create_workqueue is deprecated. The workqueue usage does not seem to
>> demand any special treatment, so do not set any flags either.
>>
>> Signed-off-by: John W. Linville <linville@tuxdriver.com>
>> ---
>> I don't have the hardware to test...
>
> Hold off on this one. It seems to break the driver, but I do not
> know why just yet.
There are two differences between create_workqueue(name) and
alloc_workqueue(name, 0, 0).
* The former has WQ_MEM_RECLAIM set and forward progress is guaranteed
regardless of memory pressure. In this case, this shouldn't make
any difference.
* The former has @max_active set to 1 while the latter to
WQ_DFL_ACTIVE. IOW, works queued on the same CPU would be allowed
to run concurrently while before conversion only different CPUs can
run works queued to the workqueue in parallel. This usually
shouldn't make difference either as works could have run in parallel
on different CPUs before too.
Does alloc_workqueue(name, 0, 1) fix the problem? If so, it might be
that the current workqueue usage has problem too.
Thanks.
--
tejun
^ permalink raw reply
* Re: [RFC 3/8] cfg80211: pass DFS region to drivers through reg_notifier()
From: Johannes Berg @ 2010-12-17 9:50 UTC (permalink / raw)
To: Luis R. Rodriguez; +Cc: linux-wireless
In-Reply-To: <1292556197-4820-4-git-send-email-lrodriguez@atheros.com>
On Thu, 2010-12-16 at 19:23 -0800, Luis R. Rodriguez wrote:
> /* Lets us get back the wiphy on the callback */
> int (*reg_notifier)(struct wiphy *wiphy,
> - struct regulatory_request *request);
> + struct regulatory_request *request,
> + u8 dfs_region);
So does that mean we need to implement a reg_notifier if we want to have
radar detection? Doesn't an empty reg_notifier already alter behaviour
somewhere which would make this not feasible?
johannes
^ permalink raw reply
* Re: [RFC 2/8] cfg80211: process new country regulatory flags (DFS)
From: Johannes Berg @ 2010-12-17 9:49 UTC (permalink / raw)
To: Luis R. Rodriguez; +Cc: linux-wireless
In-Reply-To: <1292556197-4820-3-git-send-email-lrodriguez@atheros.com>
On Thu, 2010-12-16 at 19:23 -0800, Luis R. Rodriguez wrote:
> + * @NL80211_ATTR_REG_COUNTRY_FLAGS: Country specific regulatory flags.
> + * These are @NL80211_CFLAG_DFS_FCC_*
How many FCCs are there? ;-)
johannes
^ permalink raw reply
* Re: Problem bringing up wlan0 interface up with mainline wl1271 drivers
From: Elvis Dowson @ 2010-12-17 9:44 UTC (permalink / raw)
To: Arik Nemtsov
Cc: panduranga, Ohad Ben-Cohen, Linux Wireless Mailing List,
Jara, Pedro
In-Reply-To: <AANLkTinejL9LeocQPzjrqrCFYbrF9wqpD9dSyfEVu8us@mail.gmail.com>
On Dec 17, 2010, at 12:51 PM, Arik Nemtsov wrote:
> Ethernet addresses with the LSB of the first octet turned on are considered multicast addresses. Please try:
>
> ifconfig wlan0 hw ether 00:22:33:44:55:66
That worked, now the only thing is to put the firmware file in the appropriate place, I guess:
# ifconfig wlan0 hw ether 00:22:33:44:55:66
# ifconfig wlan0 up
[ 153.843597] wl1271: ERROR could not get firmware: -2
Where should the firmware file be located? /etc/firmware ?
Elvis Dowson
^ permalink raw reply
* Re: Problem bringing up wlan0 interface up with mainline wl1271 drivers
From: Elvis Dowson @ 2010-12-17 9:33 UTC (permalink / raw)
To: panduranga; +Cc: Ohad Ben-Cohen, Linux Wireless Mailing List, Jara, Pedro
In-Reply-To: <E680F3C4CE6F415E95DCBDA48F0158FC@MINX0125717>
Hi,
On Dec 17, 2010, at 9:11 AM, panduranga wrote:
> add the following patch (http://www.spinics.net/lists/linux-wireless/msg59391.html) by Arik Nemtsov.
>
> diff --git a/drivers/net/wireless/wl12xx/main.c b/drivers/net/wireless/wl12xx/main.c
> index 708b699..e5fbbb6 100644
> --- a/drivers/net/wireless/wl12xx/main.c
> +++ b/drivers/net/wireless/wl12xx/main.c
> @@ -2987,6 +2987,18 @@ int wl1271_register_hw(struct wl1271 *wl)
> if (wl->mac80211_registered)
> return 0;
>
> + ret = wl1271_fetch_nvs(wl);
> + if (ret == 0) {
> + u8 *nvs_ptr = (u8 *)wl->nvs->nvs;
> +
> + wl->mac_addr[0] = nvs_ptr[11];
> + wl->mac_addr[1] = nvs_ptr[10];
> + wl->mac_addr[2] = nvs_ptr[6];
> + wl->mac_addr[3] = nvs_ptr[5];
> + wl->mac_addr[4] = nvs_ptr[4];
> + wl->mac_addr[5] = nvs_ptr[3];
> + }
> +
> SET_IEEE80211_PERM_ADDR(wl->hw, wl->mac_addr);
>
> ret = ieee80211_register_hw(wl->hw);
Where should the firmware file be located? What name should I give the firmware file : firmware.bin ?
I get the following error after adding the following patch:
[ 62.835174] wl1271: ERROR could not get nvs file: -2
[ 62.887786] wl1271: loaded
[ 62.890655] wl1271: initialized
Elvis Dowson
^ permalink raw reply
* Problem bringing up wlan0 interface up with mainline wl1271 drivers
From: Arik Nemtsov @ 2010-12-17 8:59 UTC (permalink / raw)
To: Elvis Dowson
Cc: panduranga, Ohad Ben-Cohen, Linux Wireless Mailing List,
Jara, Pedro
In-Reply-To: <AANLkTinejL9LeocQPzjrqrCFYbrF9wqpD9dSyfEVu8us@mail.gmail.com>
[ resending to list since it rejects html subparts ]
Hey Elvis,
>
> On Fri, Dec 17, 2010 at 10:36, Elvis Dowson <elvis.dowson@mac.com> wrote:
>>
>> Hi,
>>
>> On Dec 17, 2010, at 9:11 AM, panduranga wrote:
>>
>> # ifconfig wlan0 hw ether 11:22:33:44:55:66
>> SIOCSIFHWADDR: Cannot assign requested address
>>
>> Even trying to assign an IP address doesn't work.
>>
>> # ifconfig wlan0 inet 192.168.1.105 netmask 255.255.255.0
>> SIOCSIFFLAGS: Cannot assign requested address
>>
>
Ethernet addresses with the LSB of the first octet turned on are
considered multicast addresses. Please try:
ifconfig wlan0 hw ether 00:22:33:44:55:66
Regards,
Arik
^ permalink raw reply
* Re: Problem bringing up wlan0 interface up with mainline wl1271 drivers
From: Elvis Dowson @ 2010-12-17 8:36 UTC (permalink / raw)
To: panduranga; +Cc: Ohad Ben-Cohen, Linux Wireless Mailing List, Jara, Pedro
In-Reply-To: <E680F3C4CE6F415E95DCBDA48F0158FC@MINX0125717>
Hi,
On Dec 17, 2010, at 9:11 AM, panduranga wrote:
> This because you havent set the mac address for wlan0
>
> wlan0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
>
> You can do by using the following command:
> ifconfig wlan0 hw ether 11:22:33:44:55:66
I tried that earlier, but got the same results.
# ifconfig wlan0 hw ether 11:22:33:44:55:66
SIOCSIFHWADDR: Cannot assign requested address
Even trying to assign an IP address doesn't work.
# ifconfig wlan0 inet 192.168.1.105 netmask 255.255.255.0
SIOCSIFFLAGS: Cannot assign requested address
Here's how my modified board-omap3beagle.c looks like, for the mainline wl1271 drivers. (The modifications for the board file and the board-wifi for the TI proprietary drivers are different, and that is a separate issue that I'm working on in parallel for android-2.6.32 kernel).
>From e84ded71b45aecd340ec6030a540d0305c43c82d Mon Sep 17 00:00:00 2001
From: Elvis Dowson <elvis.dowson@gmail.com>
Date: Fri, 17 Dec 2010 12:27:23 +0400
Subject: [PATCH] Add support for Murata wl1271 wlan module.
---
arch/arm/mach-omap2/Makefile | 1 +
arch/arm/mach-omap2/board-beagle20-wifi.c | 64 ++++++++++++++++++++++++++
arch/arm/mach-omap2/board-beagle20-wifi.h | 24 ++++++++++
arch/arm/mach-omap2/board-omap3beagle.c | 62 +++++++++++++++++++++++++
4 files changed, 151 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-omap2/board-beagle20-wifi.c
create mode 100644 arch/arm/mach-omap2/board-beagle20-wifi.h
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 60e51bc..36f2b69 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -119,6 +119,7 @@ obj-$(CONFIG_MACH_OMAP_2430SDP) += board-2430sdp.o \
hsmmc.o
obj-$(CONFIG_MACH_OMAP_APOLLON) += board-apollon.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o \
+ board-beagle20-wifi.o \
hsmmc.o
obj-$(CONFIG_MACH_DEVKIT8000) += board-devkit8000.o \
hsmmc.o
diff --git a/arch/arm/mach-omap2/board-beagle20-wifi.c b/arch/arm/mach-omap2/board-beagle20-wifi.c
new file mode 100644
index 0000000..4f75e2d
--- /dev/null
+++ b/arch/arm/mach-omap2/board-beagle20-wifi.c
@@ -0,0 +1,64 @@
+/*
+ * linux/arch/arm/mach-omap2/board-beagle20-wifi.c
+ *
+ *
+ *
+ * Copyright (C) 2010 Texas Instruments Inc.
+ *
+ * Author :
+ * Elvis Dowson <elvis.dowson@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+
+#include <linux/mmc/host.h>
+#include <linux/mmc/sdio_ids.h>
+
+#include <linux/gpio.h>
+
+#include "board-beagle20-wifi.h"
+#include "mux.h"
+
+void wlan_mux_init(void)
+{
+ pr_info("%s: Configuring mux settings for wl1271 wlan module\n", __func__);
+
+ /* OMAP_BEAGLE20_WIFI_PMENA_GPIO and OMAP_BEAGLE20_WIFI_IRQ_GPIO */
+ omap_mux_init_gpio(OMAP_BEAGLE20_WIFI_PMENA_GPIO, OMAP_PIN_OUTPUT);
+ omap_mux_init_gpio(OMAP_BEAGLE20_WIFI_IRQ_GPIO, OMAP_PIN_INPUT_PULLUP);
+
+ /*
+ * MMC2 pin mux settings.
+ *
+ * The pix mux strings can be found in /arch/arm/mach-omap2/mux34xx.c
+ *
+ * Refer the TI OMAP 35x Technical Reference Manual (Rev.D), page 840
+ * for the following example.
+ *
+ * If the string name is “xxx.yyy”
+ * xxx – is the name of the default mode of the pad, usually Mode 0
+ * as described in the TRM.
+ * yyy – is the pin on that pad you want to select.
+ *
+ * For example, MMC3 CLK line ("sdmmc3_clk") can be brought out in
+ * 2 places ("mcspi1_cs2" and "etk_clk").
+ *
+ */
+ omap_mux_init_signal("sdmmc2_clk.sdmmc2_clk", OMAP_PIN_INPUT_PULLUP);
+ omap_mux_init_signal("sdmmc2_cmd.sdmmc2_cmd", OMAP_PIN_INPUT_PULLUP);
+ omap_mux_init_signal("sdmmc2_dat0.sdmmc2_dat0", OMAP_PIN_INPUT_PULLUP);
+ omap_mux_init_signal("sdmmc2_dat1.sdmmc2_dat1", OMAP_PIN_INPUT_PULLUP);
+ omap_mux_init_signal("sdmmc2_dat2.sdmmc2_dat2", OMAP_PIN_INPUT_PULLUP);
+ omap_mux_init_signal("sdmmc2_dat3.sdmmc2_dat3", OMAP_PIN_INPUT_PULLUP);
+}
+
diff --git a/arch/arm/mach-omap2/board-beagle20-wifi.h b/arch/arm/mach-omap2/board-beagle20-wifi.h
new file mode 100644
index 0000000..5ce7df2
--- /dev/null
+++ b/arch/arm/mach-omap2/board-beagle20-wifi.h
@@ -0,0 +1,24 @@
+/*
+ * linux/arch/arm/mach-omap2/board-beagle20-wifi.h
+ *
+ *
+ *
+ * Copyright (C) 2010 Texas Instruments Inc.
+ *
+ * Author :
+ * Elvis Dowson <elvis.dowson@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef BOARD_BEAGLE20_WIFI_H_
+#define BOARD_BEAGLE20_WIFI_H_
+
+#define OMAP_BEAGLE20_WIFI_PMENA_GPIO 94 /* Murata TI WL1271 WLAN module enable GPIO */
+#define OMAP_BEAGLE20_WIFI_IRQ_GPIO 97 /* Murata TI WL1271 WLAN module IRQ GPIO */
+
+void wlan_mux_init(void);
+
+#endif /* BOARD_BEAGLE20_WIFI_H_ */
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 50af879..6d1fcd6 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -30,7 +30,9 @@
#include <linux/mmc/host.h>
#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
#include <linux/i2c/twl.h>
+#include <linux/wl12xx.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -45,6 +47,7 @@
#include <plat/nand.h>
#include <plat/usb.h>
+#include "board-beagle20-wifi.h"
#include "mux.h"
#include "hsmmc.h"
#include "timer-gp.h"
@@ -166,6 +169,14 @@ static struct omap2_hsmmc_info mmc[] = {
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
},
+ {
+ .name = "wl1271",
+ .mmc = 2,
+ .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
+ .gpio_wp = -EINVAL,
+ .gpio_cd = -EINVAL,
+ .nonremovable = true,
+ },
{} /* Terminator */
};
@@ -177,6 +188,10 @@ static struct regulator_consumer_supply beagle_vsim_supply = {
.supply = "vmmc_aux",
};
+static struct regulator_consumer_supply beagle_vmmc2_supply = {
+ .supply = "vmmc",
+};
+
static struct gpio_led gpio_leds[];
static int beagle_twl_gpio_setup(struct device *dev,
@@ -187,6 +202,7 @@ static int beagle_twl_gpio_setup(struct device *dev,
/* link regulators to MMC adapters */
beagle_vmmc1_supply.dev = mmc[0].dev;
beagle_vsim_supply.dev = mmc[0].dev;
+ beagle_vmmc2_supply.dev = mmc[1].dev;
return 0;
}
@@ -217,6 +233,21 @@ static struct regulator_init_data beagle_vmmc1 = {
.consumer_supplies = &beagle_vmmc1_supply,
};
+/* VMMC2 for MMC2 card */
+static struct regulator_init_data beagle_vmmc2 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 1850000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &beagle_vmmc2_supply,
+};
+
/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
static struct regulator_init_data beagle_vsim = {
.constraints = {
@@ -261,6 +292,31 @@ static struct regulator_init_data beagle_vpll2 = {
.consumer_supplies = &beagle_vdvi_supply,
};
+/* Fixed voltage regulator for wlan module */
+static struct fixed_voltage_config beagle_vwlan = {
+ .supply_name = "vwl1271",
+ .microvolts = 1850000, /* 1.8V */
+ .gpio = OMAP_BEAGLE20_WIFI_PMENA_GPIO,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0,
+ .init_data = &beagle_vmmc2,
+};
+
+static struct platform_device omap_vwlan_device = {
+ .name = "reg-fixed-voltage",
+ .id = 1,
+ .dev = {
+ .platform_data = &beagle_vwlan,
+ },
+};
+
+struct wl12xx_platform_data omap_beagle_wlan_data __initdata = {
+ .irq = OMAP_GPIO_IRQ(OMAP_BEAGLE20_WIFI_IRQ_GPIO),
+ /* ZOOM ref clock is 26 MHz */
+ .board_ref_clock = 1,
+};
+
static struct twl4030_usb_data beagle_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
@@ -455,6 +511,12 @@ static void __init omap3_beagle_init(void)
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
beagle_display_init();
+
+ /* wl12xx wlan module */
+ wlan_mux_init();
+ if (wl12xx_set_platform_data(&omap_beagle_wlan_data))
+ pr_err("error setting wl12xx data\n");
+ platform_device_register(&omap_vwlan_device);
}
MACHINE_START(OMAP3_BEAGLE, "Custom BeagleBoard 2.0")
--
1.7.0.4
^ permalink raw reply related
* Re: [RFC 3/8] cfg80211: pass DFS region to drivers through reg_notifier()
From: Senthil Balasubramanian @ 2010-12-17 6:39 UTC (permalink / raw)
To: Luis R. Rodriguez; +Cc: linux-wireless@vger.kernel.org, Luis Rodriguez
In-Reply-To: <1292556197-4820-4-git-send-email-lrodriguez@atheros.com>
On Fri, Dec 17, 2010 at 08:53:12AM +0530, Luis R. Rodriguez wrote:
> This grants drivers access to the DFS region that a
> regulatory domain belongs to.
>
> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
> ---
> drivers/net/wireless/ath/ar9170/main.c | 6 ++++--
> drivers/net/wireless/ath/ath5k/base.c | 6 ++++--
> drivers/net/wireless/ath/ath9k/htc_drv_init.c | 6 ++++--
> drivers/net/wireless/ath/ath9k/init.c | 5 +++--
> drivers/net/wireless/ath/carl9170/main.c | 6 ++++--
> drivers/net/wireless/ath/regd.c | 9 ++++++---
> drivers/net/wireless/ath/regd.h | 5 +++--
> include/net/cfg80211.h | 3 ++-
> net/wireless/reg.c | 4 +++-
> 9 files changed, 33 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/net/wireless/ath/ar9170/main.c b/drivers/net/wireless/ath/ar9170/main.c
> index 32bf79e..7f65d3d 100644
> --- a/drivers/net/wireless/ath/ar9170/main.c
> +++ b/drivers/net/wireless/ath/ar9170/main.c
> @@ -2122,12 +2122,14 @@ static int ar9170_read_eeprom(struct ar9170 *ar)
> }
>
> static int ar9170_reg_notifier(struct wiphy *wiphy,
> - struct regulatory_request *request)
> + struct regulatory_request *request,
> + u8 dfs_region)
> {
> struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
> struct ar9170 *ar = hw->priv;
>
> - return ath_reg_notifier_apply(wiphy, request, &ar->common.regulatory);
> + return ath_reg_notifier_apply(wiphy, request,
> + &ar->common.regulatory, dfs_region);
> }
>
> int ar9170_register(struct ar9170 *ar, struct device *pdev)
> diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c
> index 4e3b97c..5a8d9a9 100644
> --- a/drivers/net/wireless/ath/ath5k/base.c
> +++ b/drivers/net/wireless/ath/ath5k/base.c
> @@ -261,13 +261,15 @@ static const struct ath_ops ath5k_common_ops = {
> * Driver Initialization *
> \***********************/
>
> -static int ath5k_reg_notifier(struct wiphy *wiphy, struct regulatory_request *request)
> +static int ath5k_reg_notifier(struct wiphy *wiphy,
> + struct regulatory_request *request,
> + u8 dfs_region)
> {
> struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
> struct ath5k_softc *sc = hw->priv;
> struct ath_regulatory *regulatory = ath5k_hw_regulatory(sc->ah);
>
> - return ath_reg_notifier_apply(wiphy, request, regulatory);
> + return ath_reg_notifier_apply(wiphy, request, regulatory, dfs_region);
> }
>
> /********************\
> diff --git a/drivers/net/wireless/ath/ath9k/htc_drv_init.c b/drivers/net/wireless/ath/ath9k/htc_drv_init.c
> index 0f6be35..2970026 100644
> --- a/drivers/net/wireless/ath/ath9k/htc_drv_init.c
> +++ b/drivers/net/wireless/ath/ath9k/htc_drv_init.c
> @@ -266,13 +266,15 @@ err:
> }
>
> static int ath9k_reg_notifier(struct wiphy *wiphy,
> - struct regulatory_request *request)
> + struct regulatory_request *request,
> + u8 dfs_region)
> {
> struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
> struct ath9k_htc_priv *priv = hw->priv;
>
> return ath_reg_notifier_apply(wiphy, request,
> - ath9k_hw_regulatory(priv->ah));
> + ath9k_hw_regulatory(priv->ah),
> + dfs_region);
> }
>
> static unsigned int ath9k_regread(void *hw_priv, u32 reg_offset)
> diff --git a/drivers/net/wireless/ath/ath9k/init.c b/drivers/net/wireless/ath/ath9k/init.c
> index 1238795..930ccec 100644
> --- a/drivers/net/wireless/ath/ath9k/init.c
> +++ b/drivers/net/wireless/ath/ath9k/init.c
> @@ -249,14 +249,15 @@ static void setup_ht_cap(struct ath_softc *sc,
> }
>
> static int ath9k_reg_notifier(struct wiphy *wiphy,
> - struct regulatory_request *request)
> + struct regulatory_request *request,
> + u8 dfs_region)
> {
> struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
> struct ath_wiphy *aphy = hw->priv;
> struct ath_softc *sc = aphy->sc;
> struct ath_regulatory *reg = ath9k_hw_regulatory(sc->sc_ah);
>
> - return ath_reg_notifier_apply(wiphy, request, reg);
> + return ath_reg_notifier_apply(wiphy, request, reg, dfs_region);
> }
>
> /*
> diff --git a/drivers/net/wireless/ath/carl9170/main.c b/drivers/net/wireless/ath/carl9170/main.c
> index 870df8c..474a04a 100644
> --- a/drivers/net/wireless/ath/carl9170/main.c
> +++ b/drivers/net/wireless/ath/carl9170/main.c
> @@ -1774,12 +1774,14 @@ static int carl9170_parse_eeprom(struct ar9170 *ar)
> }
>
> static int carl9170_reg_notifier(struct wiphy *wiphy,
> - struct regulatory_request *request)
> + struct regulatory_request *request,
> + u8 dfs_region)
> {
> struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
> struct ar9170 *ar = hw->priv;
>
> - return ath_reg_notifier_apply(wiphy, request, &ar->common.regulatory);
> + return ath_reg_notifier_apply(wiphy, request,
> + &ar->common.regulatory, dfs_region);
> }
>
> int carl9170_register(struct ar9170 *ar)
> diff --git a/drivers/net/wireless/ath/regd.c b/drivers/net/wireless/ath/regd.c
> index 2b14775..426b514 100644
> --- a/drivers/net/wireless/ath/regd.c
> +++ b/drivers/net/wireless/ath/regd.c
> @@ -337,7 +337,8 @@ static void ath_reg_apply_world_flags(struct wiphy *wiphy,
>
> int ath_reg_notifier_apply(struct wiphy *wiphy,
> struct regulatory_request *request,
> - struct ath_regulatory *reg)
> + struct ath_regulatory *reg,
> + u16 dfs_region)
may be we can maintain consistency of dfs_regsion type. It's u8 everywhere
except here..???
> {
> /* We always apply this */
> ath_reg_apply_radar_flags(wiphy);
> @@ -453,7 +454,8 @@ static int
> ath_regd_init_wiphy(struct ath_regulatory *reg,
> struct wiphy *wiphy,
> int (*reg_notifier)(struct wiphy *wiphy,
> - struct regulatory_request *request))
> + struct regulatory_request *request,
> + u8 dfs_region))
> {
> const struct ieee80211_regdomain *regd;
>
> @@ -500,7 +502,8 @@ int
> ath_regd_init(struct ath_regulatory *reg,
> struct wiphy *wiphy,
> int (*reg_notifier)(struct wiphy *wiphy,
> - struct regulatory_request *request))
> + struct regulatory_request *request,
> + u8 dfs_region))
> {
> struct country_code_to_enum_rd *country = NULL;
> u16 regdmn;
> diff --git a/drivers/net/wireless/ath/regd.h b/drivers/net/wireless/ath/regd.h
> index 345dd97..e06c784 100644
> --- a/drivers/net/wireless/ath/regd.h
> +++ b/drivers/net/wireless/ath/regd.h
> @@ -252,11 +252,12 @@ enum CountryCode {
> bool ath_is_world_regd(struct ath_regulatory *reg);
> int ath_regd_init(struct ath_regulatory *reg, struct wiphy *wiphy,
> int (*reg_notifier)(struct wiphy *wiphy,
> - struct regulatory_request *request));
> + struct regulatory_request *request, u8 dfs_region));
> u32 ath_regd_get_band_ctl(struct ath_regulatory *reg,
> enum ieee80211_band band);
> int ath_reg_notifier_apply(struct wiphy *wiphy,
> struct regulatory_request *request,
> - struct ath_regulatory *reg);
> + struct ath_regulatory *reg,
> + u16 dfs_region);
>
> #endif
> diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
> index 1db4d8d..ae5d590 100644
> --- a/include/net/cfg80211.h
> +++ b/include/net/cfg80211.h
> @@ -1533,7 +1533,8 @@ struct wiphy {
>
> /* Lets us get back the wiphy on the callback */
> int (*reg_notifier)(struct wiphy *wiphy,
> - struct regulatory_request *request);
> + struct regulatory_request *request,
> + u8 dfs_region);
>
> /* fields below are read-only, assigned by cfg80211 */
>
> diff --git a/net/wireless/reg.c b/net/wireless/reg.c
> index a3731d2..b6780f6 100644
> --- a/net/wireless/reg.c
> +++ b/net/wireless/reg.c
> @@ -1126,6 +1126,8 @@ void wiphy_update_regulatory(struct wiphy *wiphy,
> enum nl80211_reg_initiator initiator)
> {
> enum ieee80211_band band;
> + u8 dfs_region = (cfg80211_regdomain->flags &
> + NL80211_CFLAG_ALL_DFS_FLAGS);
>
> if (ignore_reg_update(wiphy, initiator))
> goto out;
> @@ -1137,7 +1139,7 @@ out:
> reg_process_beacons(wiphy);
> reg_process_ht_flags(wiphy);
> if (wiphy->reg_notifier)
> - wiphy->reg_notifier(wiphy, last_request);
> + wiphy->reg_notifier(wiphy, last_request, dfs_region);
> }
>
> static void handle_channel_custom(struct wiphy *wiphy,
> --
> 1.7.3.2.90.gd4c43
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: Problem bringing up wlan0 interface up with mainline wl1271 drivers
From: panduranga @ 2010-12-17 5:11 UTC (permalink / raw)
To: Elvis Dowson, Ohad Ben-Cohen; +Cc: Linux Wireless Mailing List, Jara, Pedro
In-Reply-To: <C77CCCD3-2467-4363-A513-05B68B9F57F6@mac.com>
Hi Elvis,
This because you havent set the mac address for wlan0
wlan0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
You can do by using the following command:
ifconfig wlan0 hw ether 11:22:33:44:55:66
OR
add the following patch
(http://www.spinics.net/lists/linux-wireless/msg59391.html) by Arik Nemtsov.
diff --git a/drivers/net/wireless/wl12xx/main.c
b/drivers/net/wireless/wl12xx/main.c
index 708b699..e5fbbb6 100644
--- a/drivers/net/wireless/wl12xx/main.c
+++ b/drivers/net/wireless/wl12xx/main.c
@@ -2987,6 +2987,18 @@ int wl1271_register_hw(struct wl1271 *wl)
if (wl->mac80211_registered)
return 0;
+ ret = wl1271_fetch_nvs(wl);
+ if (ret == 0) {
+ u8 *nvs_ptr = (u8 *)wl->nvs->nvs;
+
+ wl->mac_addr[0] = nvs_ptr[11];
+ wl->mac_addr[1] = nvs_ptr[10];
+ wl->mac_addr[2] = nvs_ptr[6];
+ wl->mac_addr[3] = nvs_ptr[5];
+ wl->mac_addr[4] = nvs_ptr[4];
+ wl->mac_addr[5] = nvs_ptr[3];
+ }
+
SET_IEEE80211_PERM_ADDR(wl->hw, wl->mac_addr);
ret = ieee80211_register_hw(wl->hw);
--
Regards,
Pandu.
----- Original Message -----
From: "Elvis Dowson" <elvis.dowson@mac.com>
To: "Ohad Ben-Cohen" <ohad@wizery.com>
Cc: "Linux Wireless Mailing List" <linux-wireless@vger.kernel.org>;
"Mallireddy, Panduranga" <x0125717@ti.com>; "Jara, Pedro" <pedrojara@ti.com>
Sent: Friday, December 17, 2010 5:53 AM
Subject: Problem bringing up wlan0 interface up with mainline wl1271 drivers
Hi,
On Dec 12, 2010, at 1:24 AM, Ohad Ben-Cohen wrote:
>> When I build the TI WiLink drivers from the ti rowboat hardware/ti/wlan
>> project
>
> The linux-omap community can help you with mainline drivers, but no so
> much with proprietary ones. Why don't you use the upstream wl12xx
> driver ?
I've built linux kernel 2.6.37-rc6, and patched board-omap3beagle.c to
interface with MMC2 SDIO controller,
but I'm unable to bring the wlan0 interface up.
Here are the messages during kernel boot:
[ 0.000000] wlan_mux_init: Configuring mux settings for wl1271 wlan
module
[ 0.077117] regulator: vwl1271: 1850 mV normal standby
[ 2.171813] mmc1: mmc_rescan: trying to init card at 400000 Hz
[ 2.323120] mmc1: card claims to support voltages below the defined
range. These will be ignored.
[ 2.368865] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
[ 2.392150] mmc1: new SDIO card at address 0001
[ 2.787597] wl1271: loaded
[ 2.790802] wl1271: initialized
# ifconfig -a
lo Link encap:Local Loopback
LOOPBACK MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
# ifconfig wlan0 up
SIOCSIFFLAGS: Cannot assign requested address
What could the reason be?
Elvis Dowson
^ permalink raw reply related
* [PATCH] mwifiex: use debugfs_remove_recursive()
From: Bing Zhao @ 2010-12-17 3:56 UTC (permalink / raw)
To: linux-wireless
Cc: John W. Linville, Johannes Berg, Amitkumar Karwar, Kiran Divekar,
Frank Huang, Bing Zhao
From: Amitkumar Karwar <akarwar@marvell.com>
instead of keeping pointers to all entries.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
---
drivers/net/wireless/mwifiex/debugfs.c | 36 +++----------------------------
drivers/net/wireless/mwifiex/main.h | 23 --------------------
2 files changed, 4 insertions(+), 55 deletions(-)
diff --git a/drivers/net/wireless/mwifiex/debugfs.c b/drivers/net/wireless/mwifiex/debugfs.c
index 4ea5cbc..9d23c68 100644
--- a/drivers/net/wireless/mwifiex/debugfs.c
+++ b/drivers/net/wireless/mwifiex/debugfs.c
@@ -2404,14 +2404,9 @@ exit:
}
#define MWIFIEX_DFS_ADD_FILE(name) do { \
- priv->dfs_##name = \
- debugfs_create_file(#name, 0644, priv->dfs_dev_dir, \
- priv, &mwifiex_dfs_##name##_fops); \
-} while (0);
-
-#define MWIFIEX_DFS_REM_FILE(name) do { \
- if (priv->dfs_##name) \
- debugfs_remove(priv->dfs_##name); \
+ if (!debugfs_create_file(#name, 0644, priv->dfs_dev_dir, \
+ priv, &mwifiex_dfs_##name##_fops)) \
+ goto exit; \
} while (0);
#define MWIFIEX_DFS_FILE_OPS(name) \
@@ -2524,30 +2519,7 @@ mwifiex_dev_debugfs_remove(struct mwifiex_private *priv)
if (!priv)
goto exit;
- MWIFIEX_DFS_REM_FILE(info);
- MWIFIEX_DFS_REM_FILE(debug);
- MWIFIEX_DFS_REM_FILE(deepsleep);
- MWIFIEX_DFS_REM_FILE(hscfg);
- MWIFIEX_DFS_REM_FILE(amsduaggrctrl);
- MWIFIEX_DFS_REM_FILE(txaggrprio);
- MWIFIEX_DFS_REM_FILE(sleeppd);
- MWIFIEX_DFS_REM_FILE(mpactrl);
- MWIFIEX_DFS_REM_FILE(qoscfg);
- MWIFIEX_DFS_REM_FILE(atimwindow);
- MWIFIEX_DFS_REM_FILE(txratecfg);
- MWIFIEX_DFS_REM_FILE(addbapara);
- MWIFIEX_DFS_REM_FILE(addbareject);
- MWIFIEX_DFS_REM_FILE(httxcfg);
- MWIFIEX_DFS_REM_FILE(htcapinfo);
- MWIFIEX_DFS_REM_FILE(getlog);
- MWIFIEX_DFS_REM_FILE(antcfg);
- MWIFIEX_DFS_REM_FILE(regrdwr);
- MWIFIEX_DFS_REM_FILE(rdeeprom);
- MWIFIEX_DFS_REM_FILE(drvdbg);
- MWIFIEX_DFS_REM_FILE(txbufcfg);
- MWIFIEX_DFS_REM_FILE(passphrase);
- MWIFIEX_DFS_REM_FILE(esuppmode);
- MWIFIEX_DFS_REM_FILE(dev_dir);
+ debugfs_remove_recursive(priv->dfs_dev_dir);
exit:
LEAVE();
}
diff --git a/drivers/net/wireless/mwifiex/main.h b/drivers/net/wireless/mwifiex/main.h
index 8bb8b45..646cc55 100644
--- a/drivers/net/wireless/mwifiex/main.h
+++ b/drivers/net/wireless/mwifiex/main.h
@@ -419,29 +419,6 @@ struct mwifiex_private {
char version_str[128];
#ifdef CONFIG_DEBUG_FS
struct dentry *dfs_dev_dir;
- struct dentry *dfs_info;
- struct dentry *dfs_debug;
- struct dentry *dfs_deepsleep;
- struct dentry *dfs_hscfg;
- struct dentry *dfs_amsduaggrctrl;
- struct dentry *dfs_txaggrprio;
- struct dentry *dfs_sleeppd;
- struct dentry *dfs_mpactrl;
- struct dentry *dfs_qoscfg;
- struct dentry *dfs_atimwindow;
- struct dentry *dfs_txratecfg;
- struct dentry *dfs_addbapara;
- struct dentry *dfs_addbareject;
- struct dentry *dfs_httxcfg;
- struct dentry *dfs_htcapinfo;
- struct dentry *dfs_getlog;
- struct dentry *dfs_antcfg;
- struct dentry *dfs_regrdwr;
- struct dentry *dfs_rdeeprom;
- struct dentry *dfs_drvdbg;
- struct dentry *dfs_txbufcfg;
- struct dentry *dfs_passphrase;
- struct dentry *dfs_esuppmode;
#endif
u8 nick_name[16];
bool is_adhoc_link_sensed;
--
1.7.0.2
^ permalink raw reply related
* Re: [RFT] rtlwifi: use alloc_workqueue
From: Larry Finger @ 2010-12-17 3:45 UTC (permalink / raw)
To: John W. Linville; +Cc: linux-wireless, Tejun Heo
In-Reply-To: <1292529589-5904-1-git-send-email-linville@tuxdriver.com>
On 12/16/2010 01:59 PM, John W. Linville wrote:
> create_workqueue is deprecated. The workqueue usage does not seem to
> demand any special treatment, so do not set any flags either.
>
> Signed-off-by: John W. Linville <linville@tuxdriver.com>
> ---
> I don't have the hardware to test...
Hold off on this one. It seems to break the driver, but I do not know why just yet.
Larry
^ permalink raw reply
* Re: [PATCH] rtl8192ce: drop 'rtl8192c-' prefix from files
From: Larry Finger @ 2010-12-17 3:43 UTC (permalink / raw)
To: John W. Linville; +Cc: linux-wireless, Chaoming Li
In-Reply-To: <1292532216-14491-1-git-send-email-linville@tuxdriver.com>
On 12/16/2010 02:43 PM, John W. Linville wrote:
> Signed-off-by: John W. Linville <linville@tuxdriver.com>
> ---
> Any objections? It's less to type/read/whatever...
No objections. Please add a "Tested-by:" to it.
Larry
^ permalink raw reply
* [RFC 8/8] wireless-regdb: add FCC as the DFS region for US
From: Luis R. Rodriguez @ 2010-12-17 3:23 UTC (permalink / raw)
To: linux-wireless; +Cc: Luis R. Rodriguez
In-Reply-To: <1292556197-4820-1-git-send-email-lrodriguez@atheros.com>
DFS master support in the US requires consideration for DFS
requirements as defined by the FCC rules.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
---
db.txt | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/db.txt b/db.txt
index e63a43e..d1616ef 100644
--- a/db.txt
+++ b/db.txt
@@ -611,7 +611,7 @@ country TR:
country UA:
(2402 - 2482 @ 40), (N/A, 20)
-country US:
+country US: DFS-FCC
(2402 - 2472 @ 40), (3, 27)
(5170 - 5250 @ 40), (3, 17)
(5250 - 5330 @ 40), (3, 20), DFS
--
1.7.3.2.90.gd4c43
^ permalink raw reply related
* [RFC 7/8] iw: add DFS region parsing support
From: Luis R. Rodriguez @ 2010-12-17 3:23 UTC (permalink / raw)
To: linux-wireless; +Cc: Luis R. Rodriguez
In-Reply-To: <1292556197-4820-1-git-send-email-lrodriguez@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
---
reg.c | 36 +++++++++++++++++++++++++++++++++++-
1 files changed, 35 insertions(+), 1 deletions(-)
diff --git a/reg.c b/reg.c
index 7f82e08..3c1b334 100644
--- a/reg.c
+++ b/reg.c
@@ -96,6 +96,33 @@ COMMAND(reg, set, "<ISO/IEC 3166-1 alpha2>",
NL80211_CMD_REQ_SET_REG, 0, CIB_NONE, handle_reg_set,
"Notify the kernel about the current regulatory domain.");
+#define flag_check_print(_str) \
+ do { \
+ if (has_flag) \
+ printf(", "); \
+ printf(_str); \
+ has_flag = true; \
+ } while (0)
+
+static void print_dfs_region(__u16 flags)
+{
+ bool has_flag = false;
+
+ if (!flags)
+ return;
+
+ printf(" ");
+
+ if (flags & NL80211_CFLAG_DFS_FCC)
+ flag_check_print("DFS-FCC");
+ if (flags & NL80211_CFLAG_DFS_ETSI)
+ flag_check_print("DFS-ETSI");
+ if (flags & NL80211_CFLAG_DFS_JP)
+ flag_check_print("DFS-JP");
+
+ printf("\n");
+}
+
static int print_reg_handler(struct nl_msg *msg, void *arg)
{
@@ -107,8 +134,10 @@ static int print_reg_handler(struct nl_msg *msg, void *arg)
struct nlattr *tb_msg[NL80211_ATTR_MAX + 1];
struct genlmsghdr *gnlh = nlmsg_data(nlmsg_hdr(msg));
char *alpha2;
+ char calpha2[2];
struct nlattr *nl_rule;
int rem_rule;
+ __u16 dfs_region;
static struct nla_policy reg_rule_policy[NL80211_FREQUENCY_ATTR_MAX + 1] = {
[NL80211_ATTR_REG_RULE_FLAGS] = { .type = NLA_U32 },
[NL80211_ATTR_FREQ_RANGE_START] = { .type = NLA_U32 },
@@ -132,7 +161,12 @@ static int print_reg_handler(struct nl_msg *msg, void *arg)
}
alpha2 = nla_data(tb_msg[NL80211_ATTR_REG_ALPHA2]);
- printf("country %s:\n", alpha2);
+ calpha2[0] = alpha2[0];
+ calpha2[1] = alpha2[1];
+ dfs_region = nla_get_u16(tb_msg[NL80211_ATTR_REG_COUNTRY_FLAGS]);
+
+ printf("country %c%c:", calpha2[0], calpha2[1]);
+ print_dfs_region(dfs_region);
nla_for_each_nested(nl_rule, tb_msg[NL80211_ATTR_REG_RULES], rem_rule) {
struct nlattr *tb_rule[NL80211_FREQUENCY_ATTR_MAX + 1];
--
1.7.3.2.90.gd4c43
^ permalink raw reply related
* [RFC 6/8] iw: synch up nl80211.h
From: Luis R. Rodriguez @ 2010-12-17 3:23 UTC (permalink / raw)
To: linux-wireless; +Cc: Luis R. Rodriguez
In-Reply-To: <1292556197-4820-1-git-send-email-lrodriguez@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
---
nl80211.h | 55 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 55 insertions(+), 0 deletions(-)
diff --git a/nl80211.h b/nl80211.h
index 3804212..061c9a1 100644
--- a/nl80211.h
+++ b/nl80211.h
@@ -773,6 +773,9 @@ enum nl80211_commands {
* cache, a wiphy attribute.
*
* @NL80211_ATTR_DURATION: Duration of an operation in milliseconds, u32.
+ * @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that
+ * specifies the maximum duration that can be requested with the
+ * remain-on-channel operation, in milliseconds, u32.
*
* @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects.
*
@@ -851,6 +854,13 @@ enum nl80211_commands {
*
* @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16)
*
+ * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags
+ * attributes, specifying what a key should be set as default as.
+ * See &enum nl80211_key_default_types.
+ *
+ * @NL80211_ATTR_REG_COUNTRY_FLAGS: Country specific regulatory flags.
+ * These are @NL80211_CFLAG_DFS_FCC_*
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
@@ -1029,6 +1039,12 @@ enum nl80211_attrs {
NL80211_ATTR_BSS_HT_OPMODE,
+ NL80211_ATTR_KEY_DEFAULT_TYPES,
+
+ NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION,
+
+ NL80211_ATTR_REG_COUNTRY_FLAGS,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
@@ -1466,6 +1482,24 @@ enum nl80211_reg_rule_flags {
};
/**
+ * enum nl80211_cflags - country regulatory flags
+ *
+ * @NL80211_CFLAG_DFS_FCC_: Country follows DFS master rules from FCC
+ * @NL80211_CFLAG_DFS_FCC_: Country follows DFS master rules from ETSI
+ * @NL80211_CFLAG_DFS_JP_: Country follows DFS master rules from JP/Telec
+ */
+enum nl80211_cflags {
+ NL80211_CFLAG_DFS_FCC = 1<<0,
+ NL80211_CFLAG_DFS_ETSI = 1<<1,
+ NL80211_CFLAG_DFS_JP = 1<<2,
+};
+
+#define NL80211_CFLAG_ALL_DFS_FLAGS \
+ (NL80211_CFLAG_DFS_FCC | \
+ NL80211_CFLAG_DFS_ETSI | \
+ NL80211_CFLAG_DFS_JP)
+
+/**
* enum nl80211_survey_info - survey information
*
* These attribute types are used with %NL80211_ATTR_SURVEY_INFO
@@ -1775,6 +1809,23 @@ enum nl80211_wpa_versions {
};
/**
+ * enum nl80211_key_default_types - key default types
+ * @__NL80211_KEY_DEFAULT_TYPE_INVALID: invalid
+ * @NL80211_KEY_DEFAULT_TYPE_UNICAST: key should be used as default
+ * unicast key
+ * @NL80211_KEY_DEFAULT_TYPE_MULTICAST: key should be used as default
+ * multicast key
+ * @NUM_NL80211_KEY_DEFAULT_TYPES: number of default types
+ */
+enum nl80211_key_default_types {
+ __NL80211_KEY_DEFAULT_TYPE_INVALID,
+ NL80211_KEY_DEFAULT_TYPE_UNICAST,
+ NL80211_KEY_DEFAULT_TYPE_MULTICAST,
+
+ NUM_NL80211_KEY_DEFAULT_TYPES
+};
+
+/**
* enum nl80211_key_attributes - key attributes
* @__NL80211_KEY_INVALID: invalid
* @NL80211_KEY_DATA: (temporal) key data; for TKIP this consists of
@@ -1790,6 +1841,9 @@ enum nl80211_wpa_versions {
* @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not
* specified the default depends on whether a MAC address was
* given with the command using the key or not (u32)
+ * @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags
+ * attributes, specifying what a key should be set as default as.
+ * See &enum nl80211_key_default_types.
* @__NL80211_KEY_AFTER_LAST: internal
* @NL80211_KEY_MAX: highest key attribute
*/
@@ -1802,6 +1856,7 @@ enum nl80211_key_attributes {
NL80211_KEY_DEFAULT,
NL80211_KEY_DEFAULT_MGMT,
NL80211_KEY_TYPE,
+ NL80211_KEY_DEFAULT_TYPES,
/* keep last */
__NL80211_KEY_AFTER_LAST,
--
1.7.3.2.90.gd4c43
^ permalink raw reply related
* [RFC 5/8] crda: synch up nl80211.h header with upstream for country flags
From: Luis R. Rodriguez @ 2010-12-17 3:23 UTC (permalink / raw)
To: linux-wireless; +Cc: Luis R. Rodriguez
In-Reply-To: <1292556197-4820-1-git-send-email-lrodriguez@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
---
nl80211.h | 23 +++++++++++++++++++++++
1 files changed, 23 insertions(+), 0 deletions(-)
diff --git a/nl80211.h b/nl80211.h
index 1cee56b..061c9a1 100644
--- a/nl80211.h
+++ b/nl80211.h
@@ -858,6 +858,9 @@ enum nl80211_commands {
* attributes, specifying what a key should be set as default as.
* See &enum nl80211_key_default_types.
*
+ * @NL80211_ATTR_REG_COUNTRY_FLAGS: Country specific regulatory flags.
+ * These are @NL80211_CFLAG_DFS_FCC_*
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
@@ -1040,6 +1043,8 @@ enum nl80211_attrs {
NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION,
+ NL80211_ATTR_REG_COUNTRY_FLAGS,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
@@ -1477,6 +1482,24 @@ enum nl80211_reg_rule_flags {
};
/**
+ * enum nl80211_cflags - country regulatory flags
+ *
+ * @NL80211_CFLAG_DFS_FCC_: Country follows DFS master rules from FCC
+ * @NL80211_CFLAG_DFS_FCC_: Country follows DFS master rules from ETSI
+ * @NL80211_CFLAG_DFS_JP_: Country follows DFS master rules from JP/Telec
+ */
+enum nl80211_cflags {
+ NL80211_CFLAG_DFS_FCC = 1<<0,
+ NL80211_CFLAG_DFS_ETSI = 1<<1,
+ NL80211_CFLAG_DFS_JP = 1<<2,
+};
+
+#define NL80211_CFLAG_ALL_DFS_FLAGS \
+ (NL80211_CFLAG_DFS_FCC | \
+ NL80211_CFLAG_DFS_ETSI | \
+ NL80211_CFLAG_DFS_JP)
+
+/**
* enum nl80211_survey_info - survey information
*
* These attribute types are used with %NL80211_ATTR_SURVEY_INFO
--
1.7.3.2.90.gd4c43
^ permalink raw reply related
* [RFC 4/8] crda: synch up nl80211.h copy file
From: Luis R. Rodriguez @ 2010-12-17 3:23 UTC (permalink / raw)
To: linux-wireless; +Cc: Luis R. Rodriguez
In-Reply-To: <1292556197-4820-1-git-send-email-lrodriguez@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
---
nl80211.h | 1218 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++--
1 files changed, 1182 insertions(+), 36 deletions(-)
diff --git a/nl80211.h b/nl80211.h
index 04d4516..1cee56b 100644
--- a/nl80211.h
+++ b/nl80211.h
@@ -3,11 +3,11 @@
/*
* 802.11 netlink interface public header
*
- * Copyright 2006, 2007, 2008 Johannes Berg <johannes@sipsolutions.net>
+ * Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
* Copyright 2008 Michael Wu <flamingice@sourmilk.net>
* Copyright 2008 Luis Carlos Cobo <luisca@cozybit.com>
* Copyright 2008 Michael Buesch <mb@bu3sch.de>
- * Copyright 2008 Luis R. Rodriguez <lrodriguez@atheros.com>
+ * Copyright 2008, 2009 Luis R. Rodriguez <lrodriguez@atheros.com>
* Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
* Copyright 2008 Colin McCabe <colin@cozybit.com>
*
@@ -25,6 +25,8 @@
*
*/
+#include <linux/types.h>
+
/**
* DOC: Station handling
*
@@ -38,6 +40,43 @@
*/
/**
+ * DOC: Frame transmission/registration support
+ *
+ * Frame transmission and registration support exists to allow userspace
+ * management entities such as wpa_supplicant react to management frames
+ * that are not being handled by the kernel. This includes, for example,
+ * certain classes of action frames that cannot be handled in the kernel
+ * for various reasons.
+ *
+ * Frame registration is done on a per-interface basis and registrations
+ * cannot be removed other than by closing the socket. It is possible to
+ * specify a registration filter to register, for example, only for a
+ * certain type of action frame. In particular with action frames, those
+ * that userspace registers for will not be returned as unhandled by the
+ * driver, so that the registered application has to take responsibility
+ * for doing that.
+ *
+ * The type of frame that can be registered for is also dependent on the
+ * driver and interface type. The frame types are advertised in wiphy
+ * attributes so applications know what to expect.
+ *
+ * NOTE: When an interface changes type while registrations are active,
+ * these registrations are ignored until the interface type is
+ * changed again. This means that changing the interface type can
+ * lead to a situation that couldn't otherwise be produced, but
+ * any such registrations will be dormant in the sense that they
+ * will not be serviced, i.e. they will not receive any frames.
+ *
+ * Frame transmission allows userspace to send for example the required
+ * responses to action frames. It is subject to some sanity checking,
+ * but many frames can be transmitted. When a frame was transmitted, its
+ * status is indicated to the sending socket.
+ *
+ * For more technical details, see the corresponding command descriptions
+ * below.
+ */
+
+/**
* enum nl80211_commands - supported nl80211 commands
*
* @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -46,8 +85,12 @@
* to get a list of all present wiphys.
* @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
* %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
- * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ, and/or
- * %NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET.
+ * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ,
+ * %NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT,
+ * %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
+ * and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
+ * However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
+ * instead, the support here is for backward compatibility only.
* @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
* or rename notification. Has attributes %NL80211_ATTR_WIPHY and
* %NL80211_ATTR_WIPHY_NAME.
@@ -72,11 +115,11 @@
*
* @NL80211_CMD_GET_KEY: Get sequence counter information for a key specified
* by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC.
- * @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT or
- * %NL80211_ATTR_KEY_THRESHOLD.
+ * @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT,
+ * %NL80211_ATTR_KEY_DEFAULT_MGMT, or %NL80211_ATTR_KEY_THRESHOLD.
* @NL80211_CMD_NEW_KEY: add a key with given %NL80211_ATTR_KEY_DATA,
- * %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC and %NL80211_ATTR_KEY_CIPHER
- * attributes.
+ * %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC, %NL80211_ATTR_KEY_CIPHER,
+ * and %NL80211_ATTR_KEY_SEQ attributes.
* @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX
* or %NL80211_ATTR_MAC.
*
@@ -84,7 +127,7 @@
* %NL80222_CMD_NEW_BEACON message)
* @NL80211_CMD_SET_BEACON: set the beacon on an access point interface
* using the %NL80211_ATTR_BEACON_INTERVAL, %NL80211_ATTR_DTIM_PERIOD,
- * %NL80211_BEACON_HEAD and %NL80211_BEACON_TAIL attributes.
+ * %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL attributes.
* @NL80211_CMD_NEW_BEACON: add a new beacon to an access point interface,
* parameters are like for %NL80211_CMD_SET_BEACON.
* @NL80211_CMD_DEL_BEACON: remove the beacon, stop sending it
@@ -113,6 +156,8 @@
* @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by
* %NL80211_ATTR_IFINDEX.
*
+ * @NL80211_CMD_GET_REG: ask the wireless core to send us its currently set
+ * regulatory domain.
* @NL80211_CMD_SET_REG: Set current regulatory domain. CRDA sends this command
* after being queried by the kernel. CRDA replies by sending a regulatory
* domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our
@@ -124,7 +169,7 @@
* %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and
* %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP.
* @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
- * to the the specified ISO/IEC 3166-1 alpha2 country code. The core will
+ * to the specified ISO/IEC 3166-1 alpha2 country code. The core will
* store this as a valid request and then query userspace for it.
*
* @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the
@@ -133,6 +178,227 @@
* @NL80211_CMD_SET_MESH_PARAMS: Set mesh networking properties for the
* interface identified by %NL80211_ATTR_IFINDEX
*
+ * @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The
+ * interface is identified with %NL80211_ATTR_IFINDEX and the management
+ * frame subtype with %NL80211_ATTR_MGMT_SUBTYPE. The extra IE data to be
+ * added to the end of the specified management frame is specified with
+ * %NL80211_ATTR_IE. If the command succeeds, the requested data will be
+ * added to all specified management frames generated by
+ * kernel/firmware/driver.
+ * Note: This command has been removed and it is only reserved at this
+ * point to avoid re-using existing command number. The functionality this
+ * command was planned for has been provided with cleaner design with the
+ * option to specify additional IEs in NL80211_CMD_TRIGGER_SCAN,
+ * NL80211_CMD_AUTHENTICATE, NL80211_CMD_ASSOCIATE,
+ * NL80211_CMD_DEAUTHENTICATE, and NL80211_CMD_DISASSOCIATE.
+ *
+ * @NL80211_CMD_GET_SCAN: get scan results
+ * @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters
+ * @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to
+ * NL80211_CMD_GET_SCAN and on the "scan" multicast group)
+ * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
+ * partial scan results may be available
+ *
+ * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
+ * or noise level
+ * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
+ * NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
+ *
+ * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
+ * has been changed and provides details of the request information
+ * that caused the change such as who initiated the regulatory request
+ * (%NL80211_ATTR_REG_INITIATOR), the wiphy_idx
+ * (%NL80211_ATTR_REG_ALPHA2) on which the request was made from if
+ * the initiator was %NL80211_REGDOM_SET_BY_COUNTRY_IE or
+ * %NL80211_REGDOM_SET_BY_DRIVER, the type of regulatory domain
+ * set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is
+ * %NL80211_REG_TYPE_COUNTRY the alpha2 to which we have moved on
+ * to (%NL80211_ATTR_REG_ALPHA2).
+ * @NL80211_CMD_REG_BEACON_HINT: indicates to userspace that an AP beacon
+ * has been found while world roaming thus enabling active scan or
+ * any mode of operation that initiates TX (beacons) on a channel
+ * where we would not have been able to do either before. As an example
+ * if you are world roaming (regulatory domain set to world or if your
+ * driver is using a custom world roaming regulatory domain) and while
+ * doing a passive scan on the 5 GHz band you find an AP there (if not
+ * on a DFS channel) you will now be able to actively scan for that AP
+ * or use AP mode on your card on that same channel. Note that this will
+ * never be used for channels 1-11 on the 2 GHz band as they are always
+ * enabled world wide. This beacon hint is only sent if your device had
+ * either disabled active scanning or beaconing on a channel. We send to
+ * userspace the wiphy on which we removed a restriction from
+ * (%NL80211_ATTR_WIPHY) and the channel on which this occurred
+ * before (%NL80211_ATTR_FREQ_BEFORE) and after (%NL80211_ATTR_FREQ_AFTER)
+ * the beacon hint was processed.
+ *
+ * @NL80211_CMD_AUTHENTICATE: authentication request and notification.
+ * This command is used both as a command (request to authenticate) and
+ * as an event on the "mlme" multicast group indicating completion of the
+ * authentication process.
+ * When used as a command, %NL80211_ATTR_IFINDEX is used to identify the
+ * interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and
+ * BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
+ * the SSID (mainly for association, but is included in authentication
+ * request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ is used
+ * to specify the frequence of the channel in MHz. %NL80211_ATTR_AUTH_TYPE
+ * is used to specify the authentication type. %NL80211_ATTR_IE is used to
+ * define IEs (VendorSpecificInfo, but also including RSN IE and FT IEs)
+ * to be added to the frame.
+ * When used as an event, this reports reception of an Authentication
+ * frame in station and IBSS modes when the local MLME processed the
+ * frame, i.e., it was for the local STA and was received in correct
+ * state. This is similar to MLME-AUTHENTICATE.confirm primitive in the
+ * MLME SAP interface (kernel providing MLME, userspace SME). The
+ * included %NL80211_ATTR_FRAME attribute contains the management frame
+ * (including both the header and frame body, but not FCS). This event is
+ * also used to indicate if the authentication attempt timed out. In that
+ * case the %NL80211_ATTR_FRAME attribute is replaced with a
+ * %NL80211_ATTR_TIMED_OUT flag (and %NL80211_ATTR_MAC to indicate which
+ * pending authentication timed out).
+ * @NL80211_CMD_ASSOCIATE: association request and notification; like
+ * NL80211_CMD_AUTHENTICATE but for Association and Reassociation
+ * (similar to MLME-ASSOCIATE.request, MLME-REASSOCIATE.request,
+ * MLME-ASSOCIATE.confirm or MLME-REASSOCIATE.confirm primitives).
+ * @NL80211_CMD_DEAUTHENTICATE: deauthentication request and notification; like
+ * NL80211_CMD_AUTHENTICATE but for Deauthentication frames (similar to
+ * MLME-DEAUTHENTICATION.request and MLME-DEAUTHENTICATE.indication
+ * primitives).
+ * @NL80211_CMD_DISASSOCIATE: disassociation request and notification; like
+ * NL80211_CMD_AUTHENTICATE but for Disassociation frames (similar to
+ * MLME-DISASSOCIATE.request and MLME-DISASSOCIATE.indication primitives).
+ *
+ * @NL80211_CMD_MICHAEL_MIC_FAILURE: notification of a locally detected Michael
+ * MIC (part of TKIP) failure; sent on the "mlme" multicast group; the
+ * event includes %NL80211_ATTR_MAC to describe the source MAC address of
+ * the frame with invalid MIC, %NL80211_ATTR_KEY_TYPE to show the key
+ * type, %NL80211_ATTR_KEY_IDX to indicate the key identifier, and
+ * %NL80211_ATTR_KEY_SEQ to indicate the TSC value of the frame; this
+ * event matches with MLME-MICHAELMICFAILURE.indication() primitive
+ *
+ * @NL80211_CMD_JOIN_IBSS: Join a new IBSS -- given at least an SSID and a
+ * FREQ attribute (for the initial frequency if no peer can be found)
+ * and optionally a MAC (as BSSID) and FREQ_FIXED attribute if those
+ * should be fixed rather than automatically determined. Can only be
+ * executed on a network interface that is UP, and fixed BSSID/FREQ
+ * may be rejected. Another optional parameter is the beacon interval,
+ * given in the %NL80211_ATTR_BEACON_INTERVAL attribute, which if not
+ * given defaults to 100 TU (102.4ms).
+ * @NL80211_CMD_LEAVE_IBSS: Leave the IBSS -- no special arguments, the IBSS is
+ * determined by the network interface.
+ *
+ * @NL80211_CMD_TESTMODE: testmode command, takes a wiphy (or ifindex) attribute
+ * to identify the device, and the TESTDATA blob attribute to pass through
+ * to the driver.
+ *
+ * @NL80211_CMD_CONNECT: connection request and notification; this command
+ * requests to connect to a specified network but without separating
+ * auth and assoc steps. For this, you need to specify the SSID in a
+ * %NL80211_ATTR_SSID attribute, and can optionally specify the association
+ * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC,
+ * %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
+ * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
+ * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
+ * It is also sent as an event, with the BSSID and response IEs when the
+ * connection is established or failed to be established. This can be
+ * determined by the STATUS_CODE attribute.
+ * @NL80211_CMD_ROAM: request that the card roam (currently not implemented),
+ * sent as an event when the card/driver roamed by itself.
+ * @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
+ * userspace that a connection was dropped by the AP or due to other
+ * reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and
+ * %NL80211_ATTR_REASON_CODE attributes are used.
+ *
+ * @NL80211_CMD_SET_WIPHY_NETNS: Set a wiphy's netns. Note that all devices
+ * associated with this wiphy must be down and will follow.
+ *
+ * @NL80211_CMD_REMAIN_ON_CHANNEL: Request to remain awake on the specified
+ * channel for the specified amount of time. This can be used to do
+ * off-channel operations like transmit a Public Action frame and wait for
+ * a response while being associated to an AP on another channel.
+ * %NL80211_ATTR_IFINDEX is used to specify which interface (and thus
+ * radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
+ * frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be
+ * optionally used to specify additional channel parameters.
+ * %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
+ * to remain on the channel. This command is also used as an event to
+ * notify when the requested duration starts (it may take a while for the
+ * driver to schedule this time due to other concurrent needs for the
+ * radio).
+ * When called, this operation returns a cookie (%NL80211_ATTR_COOKIE)
+ * that will be included with any events pertaining to this request;
+ * the cookie is also used to cancel the request.
+ * @NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL: This command can be used to cancel a
+ * pending remain-on-channel duration if the desired operation has been
+ * completed prior to expiration of the originally requested duration.
+ * %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify the
+ * radio. The %NL80211_ATTR_COOKIE attribute must be given as well to
+ * uniquely identify the request.
+ * This command is also used as an event to notify when a requested
+ * remain-on-channel duration has expired.
+ *
+ * @NL80211_CMD_SET_TX_BITRATE_MASK: Set the mask of rates to be used in TX
+ * rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface
+ * and @NL80211_ATTR_TX_RATES the set of allowed rates.
+ *
+ * @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames
+ * (via @NL80211_CMD_FRAME) for processing in userspace. This command
+ * requires an interface index, a frame type attribute (optional for
+ * backward compatibility reasons, if not given assumes action frames)
+ * and a match attribute containing the first few bytes of the frame
+ * that should match, e.g. a single byte for only a category match or
+ * four bytes for vendor frames including the OUI. The registration
+ * cannot be dropped, but is removed automatically when the netlink
+ * socket is closed. Multiple registrations can be made.
+ * @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
+ * backward compatibility
+ * @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
+ * command is used both as a request to transmit a management frame and
+ * as an event indicating reception of a frame that was not processed in
+ * kernel code, but is for us (i.e., which may need to be processed in a
+ * user space application). %NL80211_ATTR_FRAME is used to specify the
+ * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and
+ * optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on
+ * which channel the frame is to be transmitted or was received. If this
+ * channel is not the current channel (remain-on-channel or the
+ * operational channel) the device will switch to the given channel and
+ * transmit the frame, optionally waiting for a response for the time
+ * specified using %NL80211_ATTR_DURATION. When called, this operation
+ * returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the
+ * TX status event pertaining to the TX request.
+ * @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
+ * command may be used with the corresponding cookie to cancel the wait
+ * time if it is known that it is no longer necessary.
+ * @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility.
+ * @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame
+ * transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
+ * the TX command and %NL80211_ATTR_FRAME includes the contents of the
+ * frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
+ * the frame.
+ * @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
+ * backward compatibility.
+ * @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
+ * is used to configure connection quality monitoring notification trigger
+ * levels.
+ * @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This
+ * command is used as an event to indicate the that a trigger level was
+ * reached.
+ * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
+ * and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed
+ * by %NL80211_ATTR_IFINDEX) shall operate on.
+ * In case multiple channels are supported by the device, the mechanism
+ * with which it switches channels is implementation-defined.
+ * When a monitor interface is given, it can only switch channel while
+ * no other interfaces are operating to avoid disturbing the operation
+ * of any other interfaces, and other interfaces will again take
+ * precedence when they are used.
+ *
+ * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
+ *
+ * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial
+ * mesh config parameters may be given.
+ * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the
+ * network is determined by the network interface.
+ *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
@@ -178,6 +444,70 @@ enum nl80211_commands {
NL80211_CMD_GET_MESH_PARAMS,
NL80211_CMD_SET_MESH_PARAMS,
+ NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */,
+
+ NL80211_CMD_GET_REG,
+
+ NL80211_CMD_GET_SCAN,
+ NL80211_CMD_TRIGGER_SCAN,
+ NL80211_CMD_NEW_SCAN_RESULTS,
+ NL80211_CMD_SCAN_ABORTED,
+
+ NL80211_CMD_REG_CHANGE,
+
+ NL80211_CMD_AUTHENTICATE,
+ NL80211_CMD_ASSOCIATE,
+ NL80211_CMD_DEAUTHENTICATE,
+ NL80211_CMD_DISASSOCIATE,
+
+ NL80211_CMD_MICHAEL_MIC_FAILURE,
+
+ NL80211_CMD_REG_BEACON_HINT,
+
+ NL80211_CMD_JOIN_IBSS,
+ NL80211_CMD_LEAVE_IBSS,
+
+ NL80211_CMD_TESTMODE,
+
+ NL80211_CMD_CONNECT,
+ NL80211_CMD_ROAM,
+ NL80211_CMD_DISCONNECT,
+
+ NL80211_CMD_SET_WIPHY_NETNS,
+
+ NL80211_CMD_GET_SURVEY,
+ NL80211_CMD_NEW_SURVEY_RESULTS,
+
+ NL80211_CMD_SET_PMKSA,
+ NL80211_CMD_DEL_PMKSA,
+ NL80211_CMD_FLUSH_PMKSA,
+
+ NL80211_CMD_REMAIN_ON_CHANNEL,
+ NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL,
+
+ NL80211_CMD_SET_TX_BITRATE_MASK,
+
+ NL80211_CMD_REGISTER_FRAME,
+ NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME,
+ NL80211_CMD_FRAME,
+ NL80211_CMD_ACTION = NL80211_CMD_FRAME,
+ NL80211_CMD_FRAME_TX_STATUS,
+ NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS,
+
+ NL80211_CMD_SET_POWER_SAVE,
+ NL80211_CMD_GET_POWER_SAVE,
+
+ NL80211_CMD_SET_CQM,
+ NL80211_CMD_NOTIFY_CQM,
+
+ NL80211_CMD_SET_CHANNEL,
+ NL80211_CMD_SET_WDS_PEER,
+
+ NL80211_CMD_FRAME_WAIT_CANCEL,
+
+ NL80211_CMD_JOIN_MESH,
+ NL80211_CMD_LEAVE_MESH,
+
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
@@ -190,6 +520,13 @@ enum nl80211_commands {
* here
*/
#define NL80211_CMD_SET_BSS NL80211_CMD_SET_BSS
+#define NL80211_CMD_SET_MGMT_EXTRA_IE NL80211_CMD_SET_MGMT_EXTRA_IE
+#define NL80211_CMD_REG_CHANGE NL80211_CMD_REG_CHANGE
+#define NL80211_CMD_AUTHENTICATE NL80211_CMD_AUTHENTICATE
+#define NL80211_CMD_ASSOCIATE NL80211_CMD_ASSOCIATE
+#define NL80211_CMD_DEAUTHENTICATE NL80211_CMD_DEAUTHENTICATE
+#define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE
+#define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT
/**
* enum nl80211_attrs - nl80211 netlink attributes
@@ -201,13 +538,27 @@ enum nl80211_commands {
* @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming)
* @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters
* @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz
- * @NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET: included with NL80211_ATTR_WIPHY_FREQ
+ * @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
* if HT20 or HT40 are allowed (i.e., 802.11n disabled if not included):
- * NL80211_SEC_CHAN_NO_HT = HT not allowed (i.e., same as not including
+ * NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including
* this attribute)
- * NL80211_SEC_CHAN_DISABLED = HT20 only
- * NL80211_SEC_CHAN_BELOW = secondary channel is below the primary channel
- * NL80211_SEC_CHAN_ABOVE = secondary channel is above the primary channel
+ * NL80211_CHAN_HT20 = HT20 only
+ * NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel
+ * NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel
+ * @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is
+ * less than or equal to the RTS threshold; allowed range: 1..255;
+ * dot11ShortRetryLimit; u8
+ * @NL80211_ATTR_WIPHY_RETRY_LONG: TX retry limit for frames whose length is
+ * greater than the RTS threshold; allowed range: 1..255;
+ * dot11ShortLongLimit; u8
+ * @NL80211_ATTR_WIPHY_FRAG_THRESHOLD: fragmentation threshold, i.e., maximum
+ * length in octets for frames; allowed range: 256..8000, disable
+ * fragmentation with (u32)-1; dot11FragmentationThreshold; u32
+ * @NL80211_ATTR_WIPHY_RTS_THRESHOLD: RTS threshold (TX frames with length
+ * larger than or equal to this use RTS/CTS handshake); allowed range:
+ * 0..65536, disable with (u32)-1; dot11RTSThreshold; u32
+ * @NL80211_ATTR_WIPHY_COVERAGE_CLASS: Coverage Class as defined by IEEE 802.11
+ * section 7.3.2.9; dot11CoverageClass; u8
*
* @NL80211_ATTR_IFINDEX: network interface index of the device to operate on
* @NL80211_ATTR_IFNAME: network interface name
@@ -231,7 +582,7 @@ enum nl80211_commands {
*
* @NL80211_ATTR_STA_AID: Association ID for the station (u16)
* @NL80211_ATTR_STA_FLAGS: flags, nested element with NLA_FLAG attributes of
- * &enum nl80211_sta_flags.
+ * &enum nl80211_sta_flags (deprecated, use %NL80211_ATTR_STA_FLAGS2)
* @NL80211_ATTR_STA_LISTEN_INTERVAL: listen interval as defined by
* IEEE 802.11 7.3.1.6 (u16).
* @NL80211_ATTR_STA_SUPPORTED_RATES: supported rates, array of supported
@@ -284,6 +635,229 @@ enum nl80211_commands {
* supported interface types, each a flag attribute with the number
* of the interface mode.
*
+ * @NL80211_ATTR_MGMT_SUBTYPE: Management frame subtype for
+ * %NL80211_CMD_SET_MGMT_EXTRA_IE.
+ *
+ * @NL80211_ATTR_IE: Information element(s) data (used, e.g., with
+ * %NL80211_CMD_SET_MGMT_EXTRA_IE).
+ *
+ * @NL80211_ATTR_MAX_NUM_SCAN_SSIDS: number of SSIDs you can scan with
+ * a single scan request, a wiphy attribute.
+ * @NL80211_ATTR_MAX_SCAN_IE_LEN: maximum length of information elements
+ * that can be added to a scan request
+ *
+ * @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz)
+ * @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive
+ * scanning and include a zero-length SSID (wildcard) for wildcard scan
+ * @NL80211_ATTR_BSS: scan result BSS
+ *
+ * @NL80211_ATTR_REG_INITIATOR: indicates who requested the regulatory domain
+ * currently in effect. This could be any of the %NL80211_REGDOM_SET_BY_*
+ * @NL80211_ATTR_REG_TYPE: indicates the type of the regulatory domain currently
+ * set. This can be one of the nl80211_reg_type (%NL80211_REGDOM_TYPE_*)
+ *
+ * @NL80211_ATTR_SUPPORTED_COMMANDS: wiphy attribute that specifies
+ * an array of command numbers (i.e. a mapping index to command number)
+ * that the driver for the given wiphy supports.
+ *
+ * @NL80211_ATTR_FRAME: frame data (binary attribute), including frame header
+ * and body, but not FCS; used, e.g., with NL80211_CMD_AUTHENTICATE and
+ * NL80211_CMD_ASSOCIATE events
+ * @NL80211_ATTR_SSID: SSID (binary attribute, 0..32 octets)
+ * @NL80211_ATTR_AUTH_TYPE: AuthenticationType, see &enum nl80211_auth_type,
+ * represented as a u32
+ * @NL80211_ATTR_REASON_CODE: ReasonCode for %NL80211_CMD_DEAUTHENTICATE and
+ * %NL80211_CMD_DISASSOCIATE, u16
+ *
+ * @NL80211_ATTR_KEY_TYPE: Key Type, see &enum nl80211_key_type, represented as
+ * a u32
+ *
+ * @NL80211_ATTR_FREQ_BEFORE: A channel which has suffered a regulatory change
+ * due to considerations from a beacon hint. This attribute reflects
+ * the state of the channel _before_ the beacon hint processing. This
+ * attributes consists of a nested attribute containing
+ * NL80211_FREQUENCY_ATTR_*
+ * @NL80211_ATTR_FREQ_AFTER: A channel which has suffered a regulatory change
+ * due to considerations from a beacon hint. This attribute reflects
+ * the state of the channel _after_ the beacon hint processing. This
+ * attributes consists of a nested attribute containing
+ * NL80211_FREQUENCY_ATTR_*
+ *
+ * @NL80211_ATTR_CIPHER_SUITES: a set of u32 values indicating the supported
+ * cipher suites
+ *
+ * @NL80211_ATTR_FREQ_FIXED: a flag indicating the IBSS should not try to look
+ * for other networks on different channels
+ *
+ * @NL80211_ATTR_TIMED_OUT: a flag indicating than an operation timed out; this
+ * is used, e.g., with %NL80211_CMD_AUTHENTICATE event
+ *
+ * @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is
+ * used for the association (&enum nl80211_mfp, represented as a u32);
+ * this attribute can be used
+ * with %NL80211_CMD_ASSOCIATE request
+ *
+ * @NL80211_ATTR_STA_FLAGS2: Attribute containing a
+ * &struct nl80211_sta_flag_update.
+ *
+ * @NL80211_ATTR_CONTROL_PORT: A flag indicating whether user space controls
+ * IEEE 802.1X port, i.e., sets/clears %NL80211_STA_FLAG_AUTHORIZED, in
+ * station mode. If the flag is included in %NL80211_CMD_ASSOCIATE
+ * request, the driver will assume that the port is unauthorized until
+ * authorized by user space. Otherwise, port is marked authorized by
+ * default in station mode.
+ * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the
+ * ethertype that will be used for key negotiation. It can be
+ * specified with the associate and connect commands. If it is not
+ * specified, the value defaults to 0x888E (PAE, 802.1X). This
+ * attribute is also used as a flag in the wiphy information to
+ * indicate that protocols other than PAE are supported.
+ * @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with
+ * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom
+ * ethertype frames used for key negotiation must not be encrypted.
+ *
+ * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
+ * We recommend using nested, driver-specific attributes within this.
+ *
+ * @NL80211_ATTR_DISCONNECTED_BY_AP: A flag indicating that the DISCONNECT
+ * event was due to the AP disconnecting the station, and not due to
+ * a local disconnect request.
+ * @NL80211_ATTR_STATUS_CODE: StatusCode for the %NL80211_CMD_CONNECT
+ * event (u16)
+ * @NL80211_ATTR_PRIVACY: Flag attribute, used with connect(), indicating
+ * that protected APs should be used.
+ *
+ * @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT and ASSOCIATE to
+ * indicate which unicast key ciphers will be used with the connection
+ * (an array of u32).
+ * @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT and ASSOCIATE to indicate
+ * which group key cipher will be used with the connection (a u32).
+ * @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT and ASSOCIATE to indicate
+ * which WPA version(s) the AP we want to associate with is using
+ * (a u32 with flags from &enum nl80211_wpa_versions).
+ * @NL80211_ATTR_AKM_SUITES: Used with CONNECT and ASSOCIATE to indicate
+ * which key management algorithm(s) to use (an array of u32).
+ *
+ * @NL80211_ATTR_REQ_IE: (Re)association request information elements as
+ * sent out by the card, for ROAM and successful CONNECT events.
+ * @NL80211_ATTR_RESP_IE: (Re)association response information elements as
+ * sent by peer, for ROAM and successful CONNECT events.
+ *
+ * @NL80211_ATTR_PREV_BSSID: previous BSSID, to be used by in ASSOCIATE
+ * commands to specify using a reassociate frame
+ *
+ * @NL80211_ATTR_KEY: key information in a nested attribute with
+ * %NL80211_KEY_* sub-attributes
+ * @NL80211_ATTR_KEYS: array of keys for static WEP keys for connect()
+ * and join_ibss(), key information is in a nested attribute each
+ * with %NL80211_KEY_* sub-attributes
+ *
+ * @NL80211_ATTR_PID: Process ID of a network namespace.
+ *
+ * @NL80211_ATTR_GENERATION: Used to indicate consistent snapshots for
+ * dumps. This number increases whenever the object list being
+ * dumped changes, and as such userspace can verify that it has
+ * obtained a complete and consistent snapshot by verifying that
+ * all dump messages contain the same generation number. If it
+ * changed then the list changed and the dump should be repeated
+ * completely from scratch.
+ *
+ * @NL80211_ATTR_4ADDR: Use 4-address frames on a virtual interface
+ *
+ * @NL80211_ATTR_SURVEY_INFO: survey information about a channel, part of
+ * the survey response for %NL80211_CMD_GET_SURVEY, nested attribute
+ * containing info as possible, see &enum survey_info.
+ *
+ * @NL80211_ATTR_PMKID: PMK material for PMKSA caching.
+ * @NL80211_ATTR_MAX_NUM_PMKIDS: maximum number of PMKIDs a firmware can
+ * cache, a wiphy attribute.
+ *
+ * @NL80211_ATTR_DURATION: Duration of an operation in milliseconds, u32.
+ * @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that
+ * specifies the maximum duration that can be requested with the
+ * remain-on-channel operation, in milliseconds, u32.
+ *
+ * @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects.
+ *
+ * @NL80211_ATTR_TX_RATES: Nested set of attributes
+ * (enum nl80211_tx_rate_attributes) describing TX rates per band. The
+ * enum nl80211_band value is used as the index (nla_type() of the nested
+ * data. If a band is not included, it will be configured to allow all
+ * rates based on negotiated supported rates information. This attribute
+ * is used with %NL80211_CMD_SET_TX_BITRATE_MASK.
+ *
+ * @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
+ * at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
+ * @NL80211_ATTR_FRAME_TYPE: A u16 indicating the frame type/subtype for the
+ * @NL80211_CMD_REGISTER_FRAME command.
+ * @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a
+ * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
+ * information about which frame types can be transmitted with
+ * %NL80211_CMD_FRAME.
+ * @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a
+ * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
+ * information about which frame types can be registered for RX.
+ *
+ * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was
+ * acknowledged by the recipient.
+ *
+ * @NL80211_ATTR_CQM: connection quality monitor configuration in a
+ * nested attribute with %NL80211_ATTR_CQM_* sub-attributes.
+ *
+ * @NL80211_ATTR_LOCAL_STATE_CHANGE: Flag attribute to indicate that a command
+ * is requesting a local authentication/association state change without
+ * invoking actual management frame exchange. This can be used with
+ * NL80211_CMD_AUTHENTICATE, NL80211_CMD_DEAUTHENTICATE,
+ * NL80211_CMD_DISASSOCIATE.
+ *
+ * @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations
+ * connected to this BSS.
+ *
+ * @NL80211_ATTR_WIPHY_TX_POWER_SETTING: Transmit power setting type. See
+ * &enum nl80211_tx_power_setting for possible values.
+ * @NL80211_ATTR_WIPHY_TX_POWER_LEVEL: Transmit power level in signed mBm units.
+ * This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING
+ * for non-automatic settings.
+ *
+ * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly
+ * means support for per-station GTKs.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting.
+ * This can be used to mask out antennas which are not attached or should
+ * not be used for transmitting. If an antenna is not selected in this
+ * bitmap the hardware is not allowed to transmit on this antenna.
+ *
+ * Each bit represents one antenna, starting with antenna 1 at the first
+ * bit. Depending on which antennas are selected in the bitmap, 802.11n
+ * drivers can derive which chainmasks to use (if all antennas belonging to
+ * a particular chain are disabled this chain should be disabled) and if
+ * a chain has diversity antennas wether diversity should be used or not.
+ * HT capabilities (STBC, TX Beamforming, Antenna selection) can be
+ * derived from the available chains after applying the antenna mask.
+ * Non-802.11n drivers can derive wether to use diversity or not.
+ * Drivers may reject configurations or RX/TX mask combinations they cannot
+ * support by returning -EINVAL.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving.
+ * This can be used to mask out antennas which are not attached or should
+ * not be used for receiving. If an antenna is not selected in this bitmap
+ * the hardware should not be configured to receive on this antenna.
+ * For a more detailed descripton see @NL80211_ATTR_WIPHY_ANTENNA_TX.
+ *
+ * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS
+ *
+ * @NL80211_ATTR_OFFCHANNEL_TX_OK: For management frame TX, the frame may be
+ * transmitted on another channel when the channel given doesn't match
+ * the current channel. If the current channel doesn't match and this
+ * flag isn't set, the frame will be rejected. This is also used as an
+ * nl80211 capability flag.
+ *
+ * @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16)
+ *
+ * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags
+ * attributes, specifying what a key should be set as default as.
+ * See &enum nl80211_key_default_types.
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
@@ -344,7 +918,127 @@ enum nl80211_attrs {
NL80211_ATTR_WIPHY_TXQ_PARAMS,
NL80211_ATTR_WIPHY_FREQ,
- NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET,
+ NL80211_ATTR_WIPHY_CHANNEL_TYPE,
+
+ NL80211_ATTR_KEY_DEFAULT_MGMT,
+
+ NL80211_ATTR_MGMT_SUBTYPE,
+ NL80211_ATTR_IE,
+
+ NL80211_ATTR_MAX_NUM_SCAN_SSIDS,
+
+ NL80211_ATTR_SCAN_FREQUENCIES,
+ NL80211_ATTR_SCAN_SSIDS,
+ NL80211_ATTR_GENERATION, /* replaces old SCAN_GENERATION */
+ NL80211_ATTR_BSS,
+
+ NL80211_ATTR_REG_INITIATOR,
+ NL80211_ATTR_REG_TYPE,
+
+ NL80211_ATTR_SUPPORTED_COMMANDS,
+
+ NL80211_ATTR_FRAME,
+ NL80211_ATTR_SSID,
+ NL80211_ATTR_AUTH_TYPE,
+ NL80211_ATTR_REASON_CODE,
+
+ NL80211_ATTR_KEY_TYPE,
+
+ NL80211_ATTR_MAX_SCAN_IE_LEN,
+ NL80211_ATTR_CIPHER_SUITES,
+
+ NL80211_ATTR_FREQ_BEFORE,
+ NL80211_ATTR_FREQ_AFTER,
+
+ NL80211_ATTR_FREQ_FIXED,
+
+
+ NL80211_ATTR_WIPHY_RETRY_SHORT,
+ NL80211_ATTR_WIPHY_RETRY_LONG,
+ NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
+ NL80211_ATTR_WIPHY_RTS_THRESHOLD,
+
+ NL80211_ATTR_TIMED_OUT,
+
+ NL80211_ATTR_USE_MFP,
+
+ NL80211_ATTR_STA_FLAGS2,
+
+ NL80211_ATTR_CONTROL_PORT,
+
+ NL80211_ATTR_TESTDATA,
+
+ NL80211_ATTR_PRIVACY,
+
+ NL80211_ATTR_DISCONNECTED_BY_AP,
+ NL80211_ATTR_STATUS_CODE,
+
+ NL80211_ATTR_CIPHER_SUITES_PAIRWISE,
+ NL80211_ATTR_CIPHER_SUITE_GROUP,
+ NL80211_ATTR_WPA_VERSIONS,
+ NL80211_ATTR_AKM_SUITES,
+
+ NL80211_ATTR_REQ_IE,
+ NL80211_ATTR_RESP_IE,
+
+ NL80211_ATTR_PREV_BSSID,
+
+ NL80211_ATTR_KEY,
+ NL80211_ATTR_KEYS,
+
+ NL80211_ATTR_PID,
+
+ NL80211_ATTR_4ADDR,
+
+ NL80211_ATTR_SURVEY_INFO,
+
+ NL80211_ATTR_PMKID,
+ NL80211_ATTR_MAX_NUM_PMKIDS,
+
+ NL80211_ATTR_DURATION,
+
+ NL80211_ATTR_COOKIE,
+
+ NL80211_ATTR_WIPHY_COVERAGE_CLASS,
+
+ NL80211_ATTR_TX_RATES,
+
+ NL80211_ATTR_FRAME_MATCH,
+
+ NL80211_ATTR_ACK,
+
+ NL80211_ATTR_PS_STATE,
+
+ NL80211_ATTR_CQM,
+
+ NL80211_ATTR_LOCAL_STATE_CHANGE,
+
+ NL80211_ATTR_AP_ISOLATE,
+
+ NL80211_ATTR_WIPHY_TX_POWER_SETTING,
+ NL80211_ATTR_WIPHY_TX_POWER_LEVEL,
+
+ NL80211_ATTR_TX_FRAME_TYPES,
+ NL80211_ATTR_RX_FRAME_TYPES,
+ NL80211_ATTR_FRAME_TYPE,
+
+ NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
+ NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
+
+ NL80211_ATTR_SUPPORT_IBSS_RSN,
+
+ NL80211_ATTR_WIPHY_ANTENNA_TX,
+ NL80211_ATTR_WIPHY_ANTENNA_RX,
+
+ NL80211_ATTR_MCAST_RATE,
+
+ NL80211_ATTR_OFFCHANNEL_TX_OK,
+
+ NL80211_ATTR_BSS_HT_OPMODE,
+
+ NL80211_ATTR_KEY_DEFAULT_TYPES,
+
+ NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION,
/* add attributes here, update the policy in nl80211.c */
@@ -352,15 +1046,33 @@ enum nl80211_attrs {
NL80211_ATTR_MAX = __NL80211_ATTR_AFTER_LAST - 1
};
+/* source-level API compatibility */
+#define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION
+
/*
* Allow user space programs to use #ifdef on new attributes by defining them
* here
*/
+#define NL80211_CMD_CONNECT NL80211_CMD_CONNECT
#define NL80211_ATTR_HT_CAPABILITY NL80211_ATTR_HT_CAPABILITY
#define NL80211_ATTR_BSS_BASIC_RATES NL80211_ATTR_BSS_BASIC_RATES
#define NL80211_ATTR_WIPHY_TXQ_PARAMS NL80211_ATTR_WIPHY_TXQ_PARAMS
#define NL80211_ATTR_WIPHY_FREQ NL80211_ATTR_WIPHY_FREQ
-#define NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET
+#define NL80211_ATTR_WIPHY_CHANNEL_TYPE NL80211_ATTR_WIPHY_CHANNEL_TYPE
+#define NL80211_ATTR_MGMT_SUBTYPE NL80211_ATTR_MGMT_SUBTYPE
+#define NL80211_ATTR_IE NL80211_ATTR_IE
+#define NL80211_ATTR_REG_INITIATOR NL80211_ATTR_REG_INITIATOR
+#define NL80211_ATTR_REG_TYPE NL80211_ATTR_REG_TYPE
+#define NL80211_ATTR_FRAME NL80211_ATTR_FRAME
+#define NL80211_ATTR_SSID NL80211_ATTR_SSID
+#define NL80211_ATTR_AUTH_TYPE NL80211_ATTR_AUTH_TYPE
+#define NL80211_ATTR_REASON_CODE NL80211_ATTR_REASON_CODE
+#define NL80211_ATTR_CIPHER_SUITES_PAIRWISE NL80211_ATTR_CIPHER_SUITES_PAIRWISE
+#define NL80211_ATTR_CIPHER_SUITE_GROUP NL80211_ATTR_CIPHER_SUITE_GROUP
+#define NL80211_ATTR_WPA_VERSIONS NL80211_ATTR_WPA_VERSIONS
+#define NL80211_ATTR_AKM_SUITES NL80211_ATTR_AKM_SUITES
+#define NL80211_ATTR_KEY NL80211_ATTR_KEY
+#define NL80211_ATTR_KEYS NL80211_ATTR_KEYS
#define NL80211_MAX_SUPP_RATES 32
#define NL80211_MAX_SUPP_REG_RULES 32
@@ -369,6 +1081,9 @@ enum nl80211_attrs {
#define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24
#define NL80211_HT_CAPABILITY_LEN 26
+#define NL80211_MAX_NR_CIPHER_SUITES 5
+#define NL80211_MAX_NR_AKM_SUITES 2
+
/**
* enum nl80211_iftype - (virtual) interface types
*
@@ -380,8 +1095,10 @@ enum nl80211_attrs {
* @NL80211_IFTYPE_WDS: wireless distribution interface
* @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
* @NL80211_IFTYPE_MESH_POINT: mesh point
+ * @NL80211_IFTYPE_P2P_CLIENT: P2P client
+ * @NL80211_IFTYPE_P2P_GO: P2P group owner
* @NL80211_IFTYPE_MAX: highest interface type number currently defined
- * @__NL80211_IFTYPE_AFTER_LAST: internal use
+ * @NUM_NL80211_IFTYPES: number of defined interface types
*
* These values are used with the %NL80211_ATTR_IFTYPE
* to set the type of an interface.
@@ -396,10 +1113,12 @@ enum nl80211_iftype {
NL80211_IFTYPE_WDS,
NL80211_IFTYPE_MONITOR,
NL80211_IFTYPE_MESH_POINT,
+ NL80211_IFTYPE_P2P_CLIENT,
+ NL80211_IFTYPE_P2P_GO,
/* keep last */
- __NL80211_IFTYPE_AFTER_LAST,
- NL80211_IFTYPE_MAX = __NL80211_IFTYPE_AFTER_LAST - 1
+ NUM_NL80211_IFTYPES,
+ NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1
};
/**
@@ -408,16 +1127,21 @@ enum nl80211_iftype {
* Station flags. When a station is added to an AP interface, it is
* assumed to be already associated (and hence authenticated.)
*
+ * @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved
* @NL80211_STA_FLAG_AUTHORIZED: station is authorized (802.1X)
* @NL80211_STA_FLAG_SHORT_PREAMBLE: station is capable of receiving frames
* with short barker preamble
* @NL80211_STA_FLAG_WME: station is WME/QoS capable
+ * @NL80211_STA_FLAG_MFP: station uses management frame protection
+ * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
+ * @__NL80211_STA_FLAG_AFTER_LAST: internal use
*/
enum nl80211_sta_flags {
__NL80211_STA_FLAG_INVALID,
NL80211_STA_FLAG_AUTHORIZED,
NL80211_STA_FLAG_SHORT_PREAMBLE,
NL80211_STA_FLAG_WME,
+ NL80211_STA_FLAG_MFP,
/* keep last */
__NL80211_STA_FLAG_AFTER_LAST,
@@ -425,6 +1149,44 @@ enum nl80211_sta_flags {
};
/**
+ * struct nl80211_sta_flag_update - station flags mask/set
+ * @mask: mask of station flags to set
+ * @set: which values to set them to
+ *
+ * Both mask and set contain bits as per &enum nl80211_sta_flags.
+ */
+struct nl80211_sta_flag_update {
+ __u32 mask;
+ __u32 set;
+} __attribute__((packed));
+
+/**
+ * enum nl80211_rate_info - bitrate information
+ *
+ * These attribute types are used with %NL80211_STA_INFO_TXRATE
+ * when getting information about the bitrate of a station.
+ *
+ * @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved
+ * @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s)
+ * @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8)
+ * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 Mhz dualchannel bitrate
+ * @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval
+ * @NL80211_RATE_INFO_MAX: highest rate_info number currently defined
+ * @__NL80211_RATE_INFO_AFTER_LAST: internal use
+ */
+enum nl80211_rate_info {
+ __NL80211_RATE_INFO_INVALID,
+ NL80211_RATE_INFO_BITRATE,
+ NL80211_RATE_INFO_MCS,
+ NL80211_RATE_INFO_40_MHZ_WIDTH,
+ NL80211_RATE_INFO_SHORT_GI,
+
+ /* keep last */
+ __NL80211_RATE_INFO_AFTER_LAST,
+ NL80211_RATE_INFO_MAX = __NL80211_RATE_INFO_AFTER_LAST - 1
+};
+
+/**
* enum nl80211_sta_info - station information
*
* These attribute types are used with %NL80211_ATTR_STA_INFO
@@ -436,6 +1198,15 @@ enum nl80211_sta_flags {
* @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station)
* @__NL80211_STA_INFO_AFTER_LAST: internal
* @NL80211_STA_INFO_MAX: highest possible station info attribute
+ * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
+ * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
+ * containing info as possible, see &enum nl80211_sta_info_txrate.
+ * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station)
+ * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this
+ * station)
+ * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station)
+ * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station)
+ * @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm)
*/
enum nl80211_sta_info {
__NL80211_STA_INFO_INVALID,
@@ -445,6 +1216,13 @@ enum nl80211_sta_info {
NL80211_STA_INFO_LLID,
NL80211_STA_INFO_PLID,
NL80211_STA_INFO_PLINK_STATE,
+ NL80211_STA_INFO_SIGNAL,
+ NL80211_STA_INFO_TX_BITRATE,
+ NL80211_STA_INFO_RX_PACKETS,
+ NL80211_STA_INFO_TX_PACKETS,
+ NL80211_STA_INFO_TX_RETRIES,
+ NL80211_STA_INFO_TX_FAILED,
+ NL80211_STA_INFO_SIGNAL_AVG,
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
@@ -456,14 +1234,14 @@ enum nl80211_sta_info {
*
* @NL80211_MPATH_FLAG_ACTIVE: the mesh path is active
* @NL80211_MPATH_FLAG_RESOLVING: the mesh path discovery process is running
- * @NL80211_MPATH_FLAG_DSN_VALID: the mesh path contains a valid DSN
+ * @NL80211_MPATH_FLAG_SN_VALID: the mesh path contains a valid SN
* @NL80211_MPATH_FLAG_FIXED: the mesh path has been manually set
* @NL80211_MPATH_FLAG_RESOLVED: the mesh path discovery process succeeded
*/
enum nl80211_mpath_flags {
NL80211_MPATH_FLAG_ACTIVE = 1<<0,
NL80211_MPATH_FLAG_RESOLVING = 1<<1,
- NL80211_MPATH_FLAG_DSN_VALID = 1<<2,
+ NL80211_MPATH_FLAG_SN_VALID = 1<<2,
NL80211_MPATH_FLAG_FIXED = 1<<3,
NL80211_MPATH_FLAG_RESOLVED = 1<<4,
};
@@ -475,19 +1253,22 @@ enum nl80211_mpath_flags {
* information about a mesh path.
*
* @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved
- * @NL80211_ATTR_MPATH_FRAME_QLEN: number of queued frames for this destination
- * @NL80211_ATTR_MPATH_DSN: destination sequence number
- * @NL80211_ATTR_MPATH_METRIC: metric (cost) of this mesh path
- * @NL80211_ATTR_MPATH_EXPTIME: expiration time for the path, in msec from now
- * @NL80211_ATTR_MPATH_FLAGS: mesh path flags, enumerated in
+ * @NL80211_MPATH_INFO_FRAME_QLEN: number of queued frames for this destination
+ * @NL80211_MPATH_INFO_SN: destination sequence number
+ * @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path
+ * @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now
+ * @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in
* &enum nl80211_mpath_flags;
- * @NL80211_ATTR_MPATH_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
- * @NL80211_ATTR_MPATH_DISCOVERY_RETRIES: mesh path discovery retries
+ * @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
+ * @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries
+ * @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number
+ * currently defind
+ * @__NL80211_MPATH_INFO_AFTER_LAST: internal use
*/
enum nl80211_mpath_info {
__NL80211_MPATH_INFO_INVALID,
NL80211_MPATH_INFO_FRAME_QLEN,
- NL80211_MPATH_INFO_DSN,
+ NL80211_MPATH_INFO_SN,
NL80211_MPATH_INFO_METRIC,
NL80211_MPATH_INFO_EXPTIME,
NL80211_MPATH_INFO_FLAGS,
@@ -511,6 +1292,8 @@ enum nl80211_mpath_info {
* @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE
* @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n
* @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n
+ * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
+ * @__NL80211_BAND_ATTR_AFTER_LAST: internal use
*/
enum nl80211_band_attr {
__NL80211_BAND_ATTR_INVALID,
@@ -531,6 +1314,7 @@ enum nl80211_band_attr {
/**
* enum nl80211_frequency_attr - frequency attributes
+ * @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz
* @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current
* regulatory domain.
@@ -542,6 +1326,9 @@ enum nl80211_band_attr {
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm
* (100 * dBm).
+ * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
+ * currently defined
+ * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
*/
enum nl80211_frequency_attr {
__NL80211_FREQUENCY_ATTR_INVALID,
@@ -561,9 +1348,13 @@ enum nl80211_frequency_attr {
/**
* enum nl80211_bitrate_attr - bitrate attributes
+ * @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps
* @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported
* in 2.4 GHz band.
+ * @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number
+ * currently defined
+ * @__NL80211_BITRATE_ATTR_AFTER_LAST: internal use
*/
enum nl80211_bitrate_attr {
__NL80211_BITRATE_ATTR_INVALID,
@@ -576,7 +1367,54 @@ enum nl80211_bitrate_attr {
};
/**
+ * enum nl80211_initiator - Indicates the initiator of a reg domain request
+ * @NL80211_REGDOM_SET_BY_CORE: Core queried CRDA for a dynamic world
+ * regulatory domain.
+ * @NL80211_REGDOM_SET_BY_USER: User asked the wireless core to set the
+ * regulatory domain.
+ * @NL80211_REGDOM_SET_BY_DRIVER: a wireless drivers has hinted to the
+ * wireless core it thinks its knows the regulatory domain we should be in.
+ * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an
+ * 802.11 country information element with regulatory information it
+ * thinks we should consider. cfg80211 only processes the country
+ * code from the IE, and relies on the regulatory domain information
+ * structure pased by userspace (CRDA) from our wireless-regdb.
+ * If a channel is enabled but the country code indicates it should
+ * be disabled we disable the channel and re-enable it upon disassociation.
+ */
+enum nl80211_reg_initiator {
+ NL80211_REGDOM_SET_BY_CORE,
+ NL80211_REGDOM_SET_BY_USER,
+ NL80211_REGDOM_SET_BY_DRIVER,
+ NL80211_REGDOM_SET_BY_COUNTRY_IE,
+};
+
+/**
+ * enum nl80211_reg_type - specifies the type of regulatory domain
+ * @NL80211_REGDOM_TYPE_COUNTRY: the regulatory domain set is one that pertains
+ * to a specific country. When this is set you can count on the
+ * ISO / IEC 3166 alpha2 country code being valid.
+ * @NL80211_REGDOM_TYPE_WORLD: the regulatory set domain is the world regulatory
+ * domain.
+ * @NL80211_REGDOM_TYPE_CUSTOM_WORLD: the regulatory domain set is a custom
+ * driver specific world regulatory domain. These do not apply system-wide
+ * and are only applicable to the individual devices which have requested
+ * them to be applied.
+ * @NL80211_REGDOM_TYPE_INTERSECTION: the regulatory domain set is the product
+ * of an intersection between two regulatory domains -- the previously
+ * set regulatory domain on the system and the last accepted regulatory
+ * domain request to be processed.
+ */
+enum nl80211_reg_type {
+ NL80211_REGDOM_TYPE_COUNTRY,
+ NL80211_REGDOM_TYPE_WORLD,
+ NL80211_REGDOM_TYPE_CUSTOM_WORLD,
+ NL80211_REGDOM_TYPE_INTERSECTION,
+};
+
+/**
* enum nl80211_reg_rule_attr - regulatory rule attributes
+ * @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional
* considerations for a given frequency range. These are the
* &enum nl80211_reg_rule_flags.
@@ -593,6 +1431,9 @@ enum nl80211_bitrate_attr {
* If you don't have one then don't send this.
* @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for
* a given frequency range. The value is in mBm (100 * dBm).
+ * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
+ * currently defined
+ * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
*/
enum nl80211_reg_rule_attr {
__NL80211_REG_RULE_ATTR_INVALID,
@@ -636,6 +1477,46 @@ enum nl80211_reg_rule_flags {
};
/**
+ * enum nl80211_survey_info - survey information
+ *
+ * These attribute types are used with %NL80211_ATTR_SURVEY_INFO
+ * when getting information about a survey.
+ *
+ * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
+ * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
+ * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
+ * @NL80211_SURVEY_INFO_IN_USE: channel is currently being used
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME: amount of time (in ms) that the radio
+ * spent on this channel
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY: amount of the time the primary
+ * channel was sensed busy (either due to activity or energy detect)
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: amount of time the extension
+ * channel was sensed busy
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_RX: amount of time the radio spent
+ * receiving data
+ * @NL80211_SURVEY_INFO_CHANNEL_TIME_TX: amount of time the radio spent
+ * transmitting data
+ * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
+ * currently defined
+ * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
+ */
+enum nl80211_survey_info {
+ __NL80211_SURVEY_INFO_INVALID,
+ NL80211_SURVEY_INFO_FREQUENCY,
+ NL80211_SURVEY_INFO_NOISE,
+ NL80211_SURVEY_INFO_IN_USE,
+ NL80211_SURVEY_INFO_CHANNEL_TIME,
+ NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY,
+ NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY,
+ NL80211_SURVEY_INFO_CHANNEL_TIME_RX,
+ NL80211_SURVEY_INFO_CHANNEL_TIME_TX,
+
+ /* keep last */
+ __NL80211_SURVEY_INFO_AFTER_LAST,
+ NL80211_SURVEY_INFO_MAX = __NL80211_SURVEY_INFO_AFTER_LAST - 1
+};
+
+/**
* enum nl80211_mntr_flags - monitor configuration flags
*
* Monitor configuration flags.
@@ -691,6 +1572,9 @@ enum nl80211_mntr_flags {
* @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh
* point.
*
+ * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
+ * source mesh point for path selection elements.
+ *
* @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically
* open peer links when we detect compatible mesh peers.
*
@@ -715,6 +1599,8 @@ enum nl80211_mntr_flags {
* @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs)
* that it takes for an HWMP information element to propagate across the mesh
*
+ * @NL80211_MESHCONF_ROOTMODE: whether root mode is enabled or not
+ *
* @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
*
* @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
@@ -734,6 +1620,8 @@ enum nl80211_meshconf_params {
NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT,
NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL,
NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME,
+ NL80211_MESHCONF_HWMP_ROOTMODE,
+ NL80211_MESHCONF_ELEMENT_TTL,
/* keep last */
__NL80211_MESHCONF_ATTR_AFTER_LAST,
@@ -774,10 +1662,268 @@ enum nl80211_txq_q {
NL80211_TXQ_Q_BK
};
-enum nl80211_sec_chan_offset {
- NL80211_SEC_CHAN_NO_HT /* No HT */,
- NL80211_SEC_CHAN_DISABLED /* HT20 only */,
- NL80211_SEC_CHAN_BELOW /* HT40- */,
- NL80211_SEC_CHAN_ABOVE /* HT40+ */
+enum nl80211_channel_type {
+ NL80211_CHAN_NO_HT,
+ NL80211_CHAN_HT20,
+ NL80211_CHAN_HT40MINUS,
+ NL80211_CHAN_HT40PLUS
+};
+
+/**
+ * enum nl80211_bss - netlink attributes for a BSS
+ *
+ * @__NL80211_BSS_INVALID: invalid
+ * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
+ * @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
+ * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
+ * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
+ * @NL80211_BSS_CAPABILITY: capability field (CPU order, u16)
+ * @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the
+ * raw information elements from the probe response/beacon (bin);
+ * if the %NL80211_BSS_BEACON_IES attribute is present, the IEs here are
+ * from a Probe Response frame; otherwise they are from a Beacon frame.
+ * However, if the driver does not indicate the source of the IEs, these
+ * IEs may be from either frame subtype.
+ * @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon
+ * in mBm (100 * dBm) (s32)
+ * @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon
+ * in unspecified units, scaled to 0..100 (u8)
+ * @NL80211_BSS_STATUS: status, if this BSS is "used"
+ * @NL80211_BSS_SEEN_MS_AGO: age of this BSS entry in ms
+ * @NL80211_BSS_BEACON_IES: binary attribute containing the raw information
+ * elements from a Beacon frame (bin); not present if no Beacon frame has
+ * yet been received
+ * @__NL80211_BSS_AFTER_LAST: internal
+ * @NL80211_BSS_MAX: highest BSS attribute
+ */
+enum nl80211_bss {
+ __NL80211_BSS_INVALID,
+ NL80211_BSS_BSSID,
+ NL80211_BSS_FREQUENCY,
+ NL80211_BSS_TSF,
+ NL80211_BSS_BEACON_INTERVAL,
+ NL80211_BSS_CAPABILITY,
+ NL80211_BSS_INFORMATION_ELEMENTS,
+ NL80211_BSS_SIGNAL_MBM,
+ NL80211_BSS_SIGNAL_UNSPEC,
+ NL80211_BSS_STATUS,
+ NL80211_BSS_SEEN_MS_AGO,
+ NL80211_BSS_BEACON_IES,
+
+ /* keep last */
+ __NL80211_BSS_AFTER_LAST,
+ NL80211_BSS_MAX = __NL80211_BSS_AFTER_LAST - 1
+};
+
+/**
+ * enum nl80211_bss_status - BSS "status"
+ * @NL80211_BSS_STATUS_AUTHENTICATED: Authenticated with this BSS.
+ * @NL80211_BSS_STATUS_ASSOCIATED: Associated with this BSS.
+ * @NL80211_BSS_STATUS_IBSS_JOINED: Joined to this IBSS.
+ *
+ * The BSS status is a BSS attribute in scan dumps, which
+ * indicates the status the interface has wrt. this BSS.
+ */
+enum nl80211_bss_status {
+ NL80211_BSS_STATUS_AUTHENTICATED,
+ NL80211_BSS_STATUS_ASSOCIATED,
+ NL80211_BSS_STATUS_IBSS_JOINED,
+};
+
+/**
+ * enum nl80211_auth_type - AuthenticationType
+ *
+ * @NL80211_AUTHTYPE_OPEN_SYSTEM: Open System authentication
+ * @NL80211_AUTHTYPE_SHARED_KEY: Shared Key authentication (WEP only)
+ * @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r)
+ * @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP)
+ * @__NL80211_AUTHTYPE_NUM: internal
+ * @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm
+ * @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by
+ * trying multiple times); this is invalid in netlink -- leave out
+ * the attribute for this on CONNECT commands.
+ */
+enum nl80211_auth_type {
+ NL80211_AUTHTYPE_OPEN_SYSTEM,
+ NL80211_AUTHTYPE_SHARED_KEY,
+ NL80211_AUTHTYPE_FT,
+ NL80211_AUTHTYPE_NETWORK_EAP,
+
+ /* keep last */
+ __NL80211_AUTHTYPE_NUM,
+ NL80211_AUTHTYPE_MAX = __NL80211_AUTHTYPE_NUM - 1,
+ NL80211_AUTHTYPE_AUTOMATIC
+};
+
+/**
+ * enum nl80211_key_type - Key Type
+ * @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key
+ * @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key
+ * @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS)
+ * @NUM_NL80211_KEYTYPES: number of defined key types
+ */
+enum nl80211_key_type {
+ NL80211_KEYTYPE_GROUP,
+ NL80211_KEYTYPE_PAIRWISE,
+ NL80211_KEYTYPE_PEERKEY,
+
+ NUM_NL80211_KEYTYPES
+};
+
+/**
+ * enum nl80211_mfp - Management frame protection state
+ * @NL80211_MFP_NO: Management frame protection not used
+ * @NL80211_MFP_REQUIRED: Management frame protection required
+ */
+enum nl80211_mfp {
+ NL80211_MFP_NO,
+ NL80211_MFP_REQUIRED,
+};
+
+enum nl80211_wpa_versions {
+ NL80211_WPA_VERSION_1 = 1 << 0,
+ NL80211_WPA_VERSION_2 = 1 << 1,
};
+
+/**
+ * enum nl80211_key_default_types - key default types
+ * @__NL80211_KEY_DEFAULT_TYPE_INVALID: invalid
+ * @NL80211_KEY_DEFAULT_TYPE_UNICAST: key should be used as default
+ * unicast key
+ * @NL80211_KEY_DEFAULT_TYPE_MULTICAST: key should be used as default
+ * multicast key
+ * @NUM_NL80211_KEY_DEFAULT_TYPES: number of default types
+ */
+enum nl80211_key_default_types {
+ __NL80211_KEY_DEFAULT_TYPE_INVALID,
+ NL80211_KEY_DEFAULT_TYPE_UNICAST,
+ NL80211_KEY_DEFAULT_TYPE_MULTICAST,
+
+ NUM_NL80211_KEY_DEFAULT_TYPES
+};
+
+/**
+ * enum nl80211_key_attributes - key attributes
+ * @__NL80211_KEY_INVALID: invalid
+ * @NL80211_KEY_DATA: (temporal) key data; for TKIP this consists of
+ * 16 bytes encryption key followed by 8 bytes each for TX and RX MIC
+ * keys
+ * @NL80211_KEY_IDX: key ID (u8, 0-3)
+ * @NL80211_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11
+ * section 7.3.2.25.1, e.g. 0x000FAC04)
+ * @NL80211_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and
+ * CCMP keys, each six bytes in little endian
+ * @NL80211_KEY_DEFAULT: flag indicating default key
+ * @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key
+ * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not
+ * specified the default depends on whether a MAC address was
+ * given with the command using the key or not (u32)
+ * @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags
+ * attributes, specifying what a key should be set as default as.
+ * See &enum nl80211_key_default_types.
+ * @__NL80211_KEY_AFTER_LAST: internal
+ * @NL80211_KEY_MAX: highest key attribute
+ */
+enum nl80211_key_attributes {
+ __NL80211_KEY_INVALID,
+ NL80211_KEY_DATA,
+ NL80211_KEY_IDX,
+ NL80211_KEY_CIPHER,
+ NL80211_KEY_SEQ,
+ NL80211_KEY_DEFAULT,
+ NL80211_KEY_DEFAULT_MGMT,
+ NL80211_KEY_TYPE,
+ NL80211_KEY_DEFAULT_TYPES,
+
+ /* keep last */
+ __NL80211_KEY_AFTER_LAST,
+ NL80211_KEY_MAX = __NL80211_KEY_AFTER_LAST - 1
+};
+
+/**
+ * enum nl80211_tx_rate_attributes - TX rate set attributes
+ * @__NL80211_TXRATE_INVALID: invalid
+ * @NL80211_TXRATE_LEGACY: Legacy (non-MCS) rates allowed for TX rate selection
+ * in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with
+ * 1 = 500 kbps) but without the IE length restriction (at most
+ * %NL80211_MAX_SUPP_RATES in a single array).
+ * @__NL80211_TXRATE_AFTER_LAST: internal
+ * @NL80211_TXRATE_MAX: highest TX rate attribute
+ */
+enum nl80211_tx_rate_attributes {
+ __NL80211_TXRATE_INVALID,
+ NL80211_TXRATE_LEGACY,
+
+ /* keep last */
+ __NL80211_TXRATE_AFTER_LAST,
+ NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1
+};
+
+/**
+ * enum nl80211_band - Frequency band
+ * @NL80211_BAND_2GHZ: 2.4 GHz ISM band
+ * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
+ */
+enum nl80211_band {
+ NL80211_BAND_2GHZ,
+ NL80211_BAND_5GHZ,
+};
+
+enum nl80211_ps_state {
+ NL80211_PS_DISABLED,
+ NL80211_PS_ENABLED,
+};
+
+/**
+ * enum nl80211_attr_cqm - connection quality monitor attributes
+ * @__NL80211_ATTR_CQM_INVALID: invalid
+ * @NL80211_ATTR_CQM_RSSI_THOLD: RSSI threshold in dBm. This value specifies
+ * the threshold for the RSSI level at which an event will be sent. Zero
+ * to disable.
+ * @NL80211_ATTR_CQM_RSSI_HYST: RSSI hysteresis in dBm. This value specifies
+ * the minimum amount the RSSI level must change after an event before a
+ * new event may be issued (to reduce effects of RSSI oscillation).
+ * @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event
+ * @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many
+ * consecutive packets were not acknowledged by the peer
+ * @__NL80211_ATTR_CQM_AFTER_LAST: internal
+ * @NL80211_ATTR_CQM_MAX: highest key attribute
+ */
+enum nl80211_attr_cqm {
+ __NL80211_ATTR_CQM_INVALID,
+ NL80211_ATTR_CQM_RSSI_THOLD,
+ NL80211_ATTR_CQM_RSSI_HYST,
+ NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT,
+ NL80211_ATTR_CQM_PKT_LOSS_EVENT,
+
+ /* keep last */
+ __NL80211_ATTR_CQM_AFTER_LAST,
+ NL80211_ATTR_CQM_MAX = __NL80211_ATTR_CQM_AFTER_LAST - 1
+};
+
+/**
+ * enum nl80211_cqm_rssi_threshold_event - RSSI threshold event
+ * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW: The RSSI level is lower than the
+ * configured threshold
+ * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the
+ * configured threshold
+ */
+enum nl80211_cqm_rssi_threshold_event {
+ NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW,
+ NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
+};
+
+
+/**
+ * enum nl80211_tx_power_setting - TX power adjustment
+ * @NL80211_TX_POWER_AUTOMATIC: automatically determine transmit power
+ * @NL80211_TX_POWER_LIMITED: limit TX power by the mBm parameter
+ * @NL80211_TX_POWER_FIXED: fix TX power to the mBm parameter
+ */
+enum nl80211_tx_power_setting {
+ NL80211_TX_POWER_AUTOMATIC,
+ NL80211_TX_POWER_LIMITED,
+ NL80211_TX_POWER_FIXED,
+};
+
#endif /* __LINUX_NL80211_H */
--
1.7.3.2.90.gd4c43
^ permalink raw reply related
* [RFC 3/8] cfg80211: pass DFS region to drivers through reg_notifier()
From: Luis R. Rodriguez @ 2010-12-17 3:23 UTC (permalink / raw)
To: linux-wireless; +Cc: Luis R. Rodriguez
In-Reply-To: <1292556197-4820-1-git-send-email-lrodriguez@atheros.com>
This grants drivers access to the DFS region that a
regulatory domain belongs to.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
---
drivers/net/wireless/ath/ar9170/main.c | 6 ++++--
drivers/net/wireless/ath/ath5k/base.c | 6 ++++--
drivers/net/wireless/ath/ath9k/htc_drv_init.c | 6 ++++--
drivers/net/wireless/ath/ath9k/init.c | 5 +++--
drivers/net/wireless/ath/carl9170/main.c | 6 ++++--
drivers/net/wireless/ath/regd.c | 9 ++++++---
drivers/net/wireless/ath/regd.h | 5 +++--
include/net/cfg80211.h | 3 ++-
net/wireless/reg.c | 4 +++-
9 files changed, 33 insertions(+), 17 deletions(-)
diff --git a/drivers/net/wireless/ath/ar9170/main.c b/drivers/net/wireless/ath/ar9170/main.c
index 32bf79e..7f65d3d 100644
--- a/drivers/net/wireless/ath/ar9170/main.c
+++ b/drivers/net/wireless/ath/ar9170/main.c
@@ -2122,12 +2122,14 @@ static int ar9170_read_eeprom(struct ar9170 *ar)
}
static int ar9170_reg_notifier(struct wiphy *wiphy,
- struct regulatory_request *request)
+ struct regulatory_request *request,
+ u8 dfs_region)
{
struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
struct ar9170 *ar = hw->priv;
- return ath_reg_notifier_apply(wiphy, request, &ar->common.regulatory);
+ return ath_reg_notifier_apply(wiphy, request,
+ &ar->common.regulatory, dfs_region);
}
int ar9170_register(struct ar9170 *ar, struct device *pdev)
diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c
index 4e3b97c..5a8d9a9 100644
--- a/drivers/net/wireless/ath/ath5k/base.c
+++ b/drivers/net/wireless/ath/ath5k/base.c
@@ -261,13 +261,15 @@ static const struct ath_ops ath5k_common_ops = {
* Driver Initialization *
\***********************/
-static int ath5k_reg_notifier(struct wiphy *wiphy, struct regulatory_request *request)
+static int ath5k_reg_notifier(struct wiphy *wiphy,
+ struct regulatory_request *request,
+ u8 dfs_region)
{
struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
struct ath5k_softc *sc = hw->priv;
struct ath_regulatory *regulatory = ath5k_hw_regulatory(sc->ah);
- return ath_reg_notifier_apply(wiphy, request, regulatory);
+ return ath_reg_notifier_apply(wiphy, request, regulatory, dfs_region);
}
/********************\
diff --git a/drivers/net/wireless/ath/ath9k/htc_drv_init.c b/drivers/net/wireless/ath/ath9k/htc_drv_init.c
index 0f6be35..2970026 100644
--- a/drivers/net/wireless/ath/ath9k/htc_drv_init.c
+++ b/drivers/net/wireless/ath/ath9k/htc_drv_init.c
@@ -266,13 +266,15 @@ err:
}
static int ath9k_reg_notifier(struct wiphy *wiphy,
- struct regulatory_request *request)
+ struct regulatory_request *request,
+ u8 dfs_region)
{
struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
struct ath9k_htc_priv *priv = hw->priv;
return ath_reg_notifier_apply(wiphy, request,
- ath9k_hw_regulatory(priv->ah));
+ ath9k_hw_regulatory(priv->ah),
+ dfs_region);
}
static unsigned int ath9k_regread(void *hw_priv, u32 reg_offset)
diff --git a/drivers/net/wireless/ath/ath9k/init.c b/drivers/net/wireless/ath/ath9k/init.c
index 1238795..930ccec 100644
--- a/drivers/net/wireless/ath/ath9k/init.c
+++ b/drivers/net/wireless/ath/ath9k/init.c
@@ -249,14 +249,15 @@ static void setup_ht_cap(struct ath_softc *sc,
}
static int ath9k_reg_notifier(struct wiphy *wiphy,
- struct regulatory_request *request)
+ struct regulatory_request *request,
+ u8 dfs_region)
{
struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
struct ath_wiphy *aphy = hw->priv;
struct ath_softc *sc = aphy->sc;
struct ath_regulatory *reg = ath9k_hw_regulatory(sc->sc_ah);
- return ath_reg_notifier_apply(wiphy, request, reg);
+ return ath_reg_notifier_apply(wiphy, request, reg, dfs_region);
}
/*
diff --git a/drivers/net/wireless/ath/carl9170/main.c b/drivers/net/wireless/ath/carl9170/main.c
index 870df8c..474a04a 100644
--- a/drivers/net/wireless/ath/carl9170/main.c
+++ b/drivers/net/wireless/ath/carl9170/main.c
@@ -1774,12 +1774,14 @@ static int carl9170_parse_eeprom(struct ar9170 *ar)
}
static int carl9170_reg_notifier(struct wiphy *wiphy,
- struct regulatory_request *request)
+ struct regulatory_request *request,
+ u8 dfs_region)
{
struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
struct ar9170 *ar = hw->priv;
- return ath_reg_notifier_apply(wiphy, request, &ar->common.regulatory);
+ return ath_reg_notifier_apply(wiphy, request,
+ &ar->common.regulatory, dfs_region);
}
int carl9170_register(struct ar9170 *ar)
diff --git a/drivers/net/wireless/ath/regd.c b/drivers/net/wireless/ath/regd.c
index 2b14775..426b514 100644
--- a/drivers/net/wireless/ath/regd.c
+++ b/drivers/net/wireless/ath/regd.c
@@ -337,7 +337,8 @@ static void ath_reg_apply_world_flags(struct wiphy *wiphy,
int ath_reg_notifier_apply(struct wiphy *wiphy,
struct regulatory_request *request,
- struct ath_regulatory *reg)
+ struct ath_regulatory *reg,
+ u16 dfs_region)
{
/* We always apply this */
ath_reg_apply_radar_flags(wiphy);
@@ -453,7 +454,8 @@ static int
ath_regd_init_wiphy(struct ath_regulatory *reg,
struct wiphy *wiphy,
int (*reg_notifier)(struct wiphy *wiphy,
- struct regulatory_request *request))
+ struct regulatory_request *request,
+ u8 dfs_region))
{
const struct ieee80211_regdomain *regd;
@@ -500,7 +502,8 @@ int
ath_regd_init(struct ath_regulatory *reg,
struct wiphy *wiphy,
int (*reg_notifier)(struct wiphy *wiphy,
- struct regulatory_request *request))
+ struct regulatory_request *request,
+ u8 dfs_region))
{
struct country_code_to_enum_rd *country = NULL;
u16 regdmn;
diff --git a/drivers/net/wireless/ath/regd.h b/drivers/net/wireless/ath/regd.h
index 345dd97..e06c784 100644
--- a/drivers/net/wireless/ath/regd.h
+++ b/drivers/net/wireless/ath/regd.h
@@ -252,11 +252,12 @@ enum CountryCode {
bool ath_is_world_regd(struct ath_regulatory *reg);
int ath_regd_init(struct ath_regulatory *reg, struct wiphy *wiphy,
int (*reg_notifier)(struct wiphy *wiphy,
- struct regulatory_request *request));
+ struct regulatory_request *request, u8 dfs_region));
u32 ath_regd_get_band_ctl(struct ath_regulatory *reg,
enum ieee80211_band band);
int ath_reg_notifier_apply(struct wiphy *wiphy,
struct regulatory_request *request,
- struct ath_regulatory *reg);
+ struct ath_regulatory *reg,
+ u16 dfs_region);
#endif
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 1db4d8d..ae5d590 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -1533,7 +1533,8 @@ struct wiphy {
/* Lets us get back the wiphy on the callback */
int (*reg_notifier)(struct wiphy *wiphy,
- struct regulatory_request *request);
+ struct regulatory_request *request,
+ u8 dfs_region);
/* fields below are read-only, assigned by cfg80211 */
diff --git a/net/wireless/reg.c b/net/wireless/reg.c
index a3731d2..b6780f6 100644
--- a/net/wireless/reg.c
+++ b/net/wireless/reg.c
@@ -1126,6 +1126,8 @@ void wiphy_update_regulatory(struct wiphy *wiphy,
enum nl80211_reg_initiator initiator)
{
enum ieee80211_band band;
+ u8 dfs_region = (cfg80211_regdomain->flags &
+ NL80211_CFLAG_ALL_DFS_FLAGS);
if (ignore_reg_update(wiphy, initiator))
goto out;
@@ -1137,7 +1139,7 @@ out:
reg_process_beacons(wiphy);
reg_process_ht_flags(wiphy);
if (wiphy->reg_notifier)
- wiphy->reg_notifier(wiphy, last_request);
+ wiphy->reg_notifier(wiphy, last_request, dfs_region);
}
static void handle_channel_custom(struct wiphy *wiphy,
--
1.7.3.2.90.gd4c43
^ permalink raw reply related
* [RFC 2/8] cfg80211: process new country regulatory flags (DFS)
From: Luis R. Rodriguez @ 2010-12-17 3:23 UTC (permalink / raw)
To: linux-wireless; +Cc: Luis R. Rodriguez
In-Reply-To: <1292556197-4820-1-git-send-email-lrodriguez@atheros.com>
This lets us pick up the new country regulatory flags.
This will later be used to inform of drivers later of
DFS parameters.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
---
include/linux/nl80211.h | 23 +++++++++++++++++++++++
include/net/regulatory.h | 1 +
net/wireless/nl80211.c | 9 +++++++++
net/wireless/reg.c | 26 ++++++++++++++++++++++++++
4 files changed, 59 insertions(+), 0 deletions(-)
diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h
index 1cee56b..061c9a1 100644
--- a/include/linux/nl80211.h
+++ b/include/linux/nl80211.h
@@ -858,6 +858,9 @@ enum nl80211_commands {
* attributes, specifying what a key should be set as default as.
* See &enum nl80211_key_default_types.
*
+ * @NL80211_ATTR_REG_COUNTRY_FLAGS: Country specific regulatory flags.
+ * These are @NL80211_CFLAG_DFS_FCC_*
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
@@ -1040,6 +1043,8 @@ enum nl80211_attrs {
NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION,
+ NL80211_ATTR_REG_COUNTRY_FLAGS,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
@@ -1477,6 +1482,24 @@ enum nl80211_reg_rule_flags {
};
/**
+ * enum nl80211_cflags - country regulatory flags
+ *
+ * @NL80211_CFLAG_DFS_FCC_: Country follows DFS master rules from FCC
+ * @NL80211_CFLAG_DFS_FCC_: Country follows DFS master rules from ETSI
+ * @NL80211_CFLAG_DFS_JP_: Country follows DFS master rules from JP/Telec
+ */
+enum nl80211_cflags {
+ NL80211_CFLAG_DFS_FCC = 1<<0,
+ NL80211_CFLAG_DFS_ETSI = 1<<1,
+ NL80211_CFLAG_DFS_JP = 1<<2,
+};
+
+#define NL80211_CFLAG_ALL_DFS_FLAGS \
+ (NL80211_CFLAG_DFS_FCC | \
+ NL80211_CFLAG_DFS_ETSI | \
+ NL80211_CFLAG_DFS_JP)
+
+/**
* enum nl80211_survey_info - survey information
*
* These attribute types are used with %NL80211_ATTR_SURVEY_INFO
diff --git a/include/net/regulatory.h b/include/net/regulatory.h
index 356d6e3..9fcb603 100644
--- a/include/net/regulatory.h
+++ b/include/net/regulatory.h
@@ -85,6 +85,7 @@ struct ieee80211_reg_rule {
struct ieee80211_regdomain {
u32 n_reg_rules;
char alpha2[2];
+ u16 flags;
struct ieee80211_reg_rule reg_rules[];
};
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 594a6ac..d255499 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -172,6 +172,7 @@ static const struct nla_policy nl80211_policy[NL80211_ATTR_MAX+1] = {
[NL80211_ATTR_MCAST_RATE] = { .type = NLA_U32 },
[NL80211_ATTR_OFFCHANNEL_TX_OK] = { .type = NLA_FLAG },
[NL80211_ATTR_KEY_DEFAULT_TYPES] = { .type = NLA_NESTED },
+ [NL80211_ATTR_REG_COUNTRY_FLAGS] = { .type = NLA_U16 },
};
/* policy for the key attributes */
@@ -2906,6 +2907,8 @@ static int nl80211_get_reg(struct sk_buff *skb, struct genl_info *info)
NLA_PUT_STRING(msg, NL80211_ATTR_REG_ALPHA2,
cfg80211_regdomain->alpha2);
+ NLA_PUT_U16(msg, NL80211_ATTR_REG_COUNTRY_FLAGS,
+ cfg80211_regdomain->flags);
nl_reg_rules = nla_nest_start(msg, NL80211_ATTR_REG_RULES);
if (!nl_reg_rules)
@@ -2963,6 +2966,7 @@ static int nl80211_set_reg(struct sk_buff *skb, struct genl_info *info)
char *alpha2 = NULL;
int rem_reg_rules = 0, r = 0;
u32 num_rules = 0, rule_idx = 0, size_of_regd;
+ u16 cflags = 0;
struct ieee80211_regdomain *rd = NULL;
if (!info->attrs[NL80211_ATTR_REG_ALPHA2])
@@ -2973,6 +2977,10 @@ static int nl80211_set_reg(struct sk_buff *skb, struct genl_info *info)
alpha2 = nla_data(info->attrs[NL80211_ATTR_REG_ALPHA2]);
+ if (info->attrs[NL80211_ATTR_REG_COUNTRY_FLAGS])
+ cflags =
+ nla_get_u16(info->attrs[NL80211_ATTR_REG_COUNTRY_FLAGS]);
+
nla_for_each_nested(nl_reg_rule, info->attrs[NL80211_ATTR_REG_RULES],
rem_reg_rules) {
num_rules++;
@@ -2999,6 +3007,7 @@ static int nl80211_set_reg(struct sk_buff *skb, struct genl_info *info)
rd->n_reg_rules = num_rules;
rd->alpha2[0] = alpha2[0];
rd->alpha2[1] = alpha2[1];
+ rd->flags = cflags;
nla_for_each_nested(nl_reg_rule, info->attrs[NL80211_ATTR_REG_RULES],
rem_reg_rules) {
diff --git a/net/wireless/reg.c b/net/wireless/reg.c
index 99d4183..a3731d2 100644
--- a/net/wireless/reg.c
+++ b/net/wireless/reg.c
@@ -1881,6 +1881,31 @@ static void print_rd_rules(const struct ieee80211_regdomain *rd)
}
}
+#define flag_check_print(_str) \
+ do { \
+ if (has_flag) \
+ pr_info(", "); \
+ pr_info(_str); \
+ has_flag = true; \
+ } while (0)
+
+static void print_country_flags(u16 flags)
+{
+ bool has_flag = false;
+
+ if (!(flags & NL80211_CFLAG_ALL_DFS_FLAGS))
+ return;
+
+ pr_info("DFS Master region:");
+
+ if (flags & NL80211_CFLAG_DFS_FCC)
+ flag_check_print("FCC");
+ if (flags & NL80211_CFLAG_DFS_ETSI)
+ flag_check_print("ETSI");
+ if (flags & NL80211_CFLAG_DFS_JP)
+ flag_check_print("JP");
+}
+
static void print_regdomain(const struct ieee80211_regdomain *rd)
{
@@ -1908,6 +1933,7 @@ static void print_regdomain(const struct ieee80211_regdomain *rd)
pr_info("Regulatory domain changed to country: %c%c\n",
rd->alpha2[0], rd->alpha2[1]);
}
+ print_country_flags(rd->flags);
print_rd_rules(rd);
}
--
1.7.3.2.90.gd4c43
^ permalink raw reply related
* [RFC 1/8] wireless-regdb: Add DFS bit fields for countries
From: Luis R. Rodriguez @ 2010-12-17 3:23 UTC (permalink / raw)
To: linux-wireless; +Cc: Luis R. Rodriguez
In-Reply-To: <1292556197-4820-1-git-send-email-lrodriguez@atheros.com>
To support DFS we add the three known DFS regions which countries
can support. In order to not modify the regulatory database scheme
in an incompatible way we use some two pad bytes which were unused
for this. This lets us later also add some more bits for general
country specific regulatory data.
We keep the regulatory database intact as otherwise older CRDA
versions will not read new regulatory file updates. Instead of
requiring new CRDA version out in the field we can treat this
as a regulatory update and simply have users who want DFS master
support to upgrade their CRDA. We'll treat the DFS region assignemnts
as a simple regulatory update.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
---
db2bin.py | 2 +-
dbparse.py | 25 ++++++++++++++++++++-----
2 files changed, 21 insertions(+), 6 deletions(-)
diff --git a/db2bin.py b/db2bin.py
index 23d3ee2..b8a153c 100755
--- a/db2bin.py
+++ b/db2bin.py
@@ -116,7 +116,7 @@ countrynames.sort()
for alpha2 in countrynames:
coll = countries[alpha2]
# struct regdb_file_reg_country
- output.write(struct.pack('>ccxxI', str(alpha2[0]), str(alpha2[1]), reg_rules_collections[coll.permissions]))
+ output.write(struct.pack('>cchI', str(alpha2[0]), str(alpha2[1]), coll.cflags, reg_rules_collections[coll.permissions]))
if len(sys.argv) > 3:
diff --git a/dbparse.py b/dbparse.py
index 2c0d738..f5087f2 100755
--- a/dbparse.py
+++ b/dbparse.py
@@ -18,6 +18,12 @@ flag_definitions = {
'NO-HT40': 1<<10,
}
+country_flag_definitions = {
+ 'DFS-FCC': 1<<0,
+ 'DFS-ETSI': 1<<1,
+ 'DFS-JP': 1<<2,
+}
+
class FreqBand(object):
def __init__(self, start, end, bw, comments=None):
self.start = start
@@ -61,6 +67,10 @@ class PowerRestriction(object):
s = self
return hash((s.max_ant_gain, s.max_eirp))
+class CountryFlagError(Exception):
+ def __init__(self, cflag):
+ self.flag = cflag
+
class FlagError(Exception):
def __init__(self, flag):
self.flag = flag
@@ -90,9 +100,15 @@ class Permission(object):
return hash(self._as_tuple())
class Country(object):
- def __init__(self, permissions=None, comments=None):
+ def __init__(self, cflags, permissions=None, comments=None):
self._permissions = permissions or []
self.comments = comments or []
+ self.cflags = 0
+ if cflags:
+ for cflag in cflags.split(','):
+ if not cflag in country_flag_definitions:
+ raise CountryFlagError(cflag)
+ self.cflags |= country_flag_definitions[cflag]
def add(self, perm):
assert isinstance(perm, Permission)
@@ -224,11 +240,10 @@ class DBParser(object):
def _parse_country(self, line):
try:
- cname, line = line.split(':', 1)
+ cname, cflags = line.split(':', 1)
+ cflags = cflags.strip()
if not cname:
self._syntax_error("'country' keyword must be followed by name")
- if line:
- self._syntax_error("extra data at end of country line")
except ValueError:
self._syntax_error("country name must be followed by colon")
@@ -239,7 +254,7 @@ class DBParser(object):
if len(cname) != 2:
self._warn("country '%s' not alpha2" % cname)
if not cname in self._countries:
- self._countries[cname] = Country(comments=self._comments)
+ self._countries[cname] = Country(cflags, comments=self._comments)
self._current_countries[cname] = self._countries[cname]
self._comments = []
--
1.7.3.2.90.gd4c43
^ permalink raw reply related
* [RFC 0/8] wireless: DFS region support
From: Luis R. Rodriguez @ 2010-12-17 3:23 UTC (permalink / raw)
To: linux-wireless; +Cc: Luis R. Rodriguez
This series has a list of changes to kernel and userspace
to start addressing DFS region support. I've cheated and
figured out a way to alter the current regulatory database
in such a way that it remains backwards compatible with
older databases so that no new CRDAs are required and we
don't have to provide two releases for old kernels and
newer kernels for wireless-regdb updates.
Let me know if this seems agreeable. In the end we end
up passing the DFS region to the drivers, the next question
then is what to do next.
Luis
^ permalink raw reply
* [PATCH 1/3 v3] mac80211: Rename mesh_params to mesh_config to prepare for mesh_setup
From: Javier Cardona @ 2010-12-17 1:25 UTC (permalink / raw)
To: John W. Linville
Cc: Javier Cardona, Steve Derosier, devel, Johannes Berg,
linux-wireless
In-Reply-To: <1292525513.3612.26.camel@jlt3.sipsolutions.net>
Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.
Signed-off-by: Javier Cardona <javier@cozybit.com>
---
v2: - separate mesh config and setup parametres and split the original patch
v3: - add #defines for source-level API compatibility
include/linux/nl80211.h | 15 ++++++++++-----
include/net/cfg80211.h | 8 ++++----
net/mac80211/cfg.c | 8 ++++----
net/wireless/nl80211.c | 40 ++++++++++++++++++++--------------------
4 files changed, 38 insertions(+), 33 deletions(-)
diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h
index 1cee56b..d626ad2 100644
--- a/include/linux/nl80211.h
+++ b/include/linux/nl80211.h
@@ -172,10 +172,10 @@
* to the specified ISO/IEC 3166-1 alpha2 country code. The core will
* store this as a valid request and then query userspace for it.
*
- * @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the
+ * @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the
* interface identified by %NL80211_ATTR_IFINDEX
*
- * @NL80211_CMD_SET_MESH_PARAMS: Set mesh networking properties for the
+ * @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the
* interface identified by %NL80211_ATTR_IFINDEX
*
* @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The
@@ -441,8 +441,8 @@ enum nl80211_commands {
NL80211_CMD_SET_REG,
NL80211_CMD_REQ_SET_REG,
- NL80211_CMD_GET_MESH_PARAMS,
- NL80211_CMD_SET_MESH_PARAMS,
+ NL80211_CMD_GET_MESH_CONFIG,
+ NL80211_CMD_SET_MESH_CONFIG,
NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */,
@@ -528,6 +528,10 @@ enum nl80211_commands {
#define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE
#define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT
+/* source-level API compatibility */
+#define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG
+#define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG
+
/**
* enum nl80211_attrs - nl80211 netlink attributes
*
@@ -912,7 +916,7 @@ enum nl80211_attrs {
NL80211_ATTR_REG_ALPHA2,
NL80211_ATTR_REG_RULES,
- NL80211_ATTR_MESH_PARAMS,
+ NL80211_ATTR_MESH_CONFIG,
NL80211_ATTR_BSS_BASIC_RATES,
@@ -1048,6 +1052,7 @@ enum nl80211_attrs {
/* source-level API compatibility */
#define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION
+#define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG
/*
* Allow user space programs to use #ifdef on new attributes by defining them
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index f45e15f..1bac74a 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -1096,9 +1096,9 @@ struct cfg80211_pmksa {
* @get_mpath: get a mesh path for the given parameters
* @dump_mpath: dump mesh path callback -- resume dump at index @idx
*
- * @get_mesh_params: Put the current mesh parameters into *params
+ * @get_mesh_config: Get the current mesh configuration
*
- * @update_mesh_params: Update mesh parameters on a running mesh.
+ * @update_mesh_config: Update mesh parameters on a running mesh.
* The mask is a bitfield which tells us which parameters to
* set, and which to leave alone.
*
@@ -1246,10 +1246,10 @@ struct cfg80211_ops {
int (*dump_mpath)(struct wiphy *wiphy, struct net_device *dev,
int idx, u8 *dst, u8 *next_hop,
struct mpath_info *pinfo);
- int (*get_mesh_params)(struct wiphy *wiphy,
+ int (*get_mesh_config)(struct wiphy *wiphy,
struct net_device *dev,
struct mesh_config *conf);
- int (*update_mesh_params)(struct wiphy *wiphy,
+ int (*update_mesh_config)(struct wiphy *wiphy,
struct net_device *dev, u32 mask,
const struct mesh_config *nconf);
int (*join_mesh)(struct wiphy *wiphy, struct net_device *dev,
diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c
index ea06f92..1c94a2a 100644
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -984,7 +984,7 @@ static int ieee80211_dump_mpath(struct wiphy *wiphy, struct net_device *dev,
return 0;
}
-static int ieee80211_get_mesh_params(struct wiphy *wiphy,
+static int ieee80211_get_mesh_config(struct wiphy *wiphy,
struct net_device *dev,
struct mesh_config *conf)
{
@@ -1000,7 +1000,7 @@ static inline bool _chg_mesh_attr(enum nl80211_meshconf_params parm, u32 mask)
return (mask >> (parm-1)) & 0x1;
}
-static int ieee80211_update_mesh_params(struct wiphy *wiphy,
+static int ieee80211_update_mesh_config(struct wiphy *wiphy,
struct net_device *dev, u32 mask,
const struct mesh_config *nconf)
{
@@ -1787,8 +1787,8 @@ struct cfg80211_ops mac80211_config_ops = {
.change_mpath = ieee80211_change_mpath,
.get_mpath = ieee80211_get_mpath,
.dump_mpath = ieee80211_dump_mpath,
- .update_mesh_params = ieee80211_update_mesh_params,
- .get_mesh_params = ieee80211_get_mesh_params,
+ .update_mesh_config = ieee80211_update_mesh_config,
+ .get_mesh_config = ieee80211_get_mesh_config,
.join_mesh = ieee80211_join_mesh,
.leave_mesh = ieee80211_leave_mesh,
#endif
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 594a6ac..d783dca 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -123,7 +123,7 @@ static const struct nla_policy nl80211_policy[NL80211_ATTR_MAX+1] = {
.len = NL80211_MAX_SUPP_RATES },
[NL80211_ATTR_BSS_HT_OPMODE] = { .type = NLA_U16 },
- [NL80211_ATTR_MESH_PARAMS] = { .type = NLA_NESTED },
+ [NL80211_ATTR_MESH_CONFIG] = { .type = NLA_NESTED },
[NL80211_ATTR_HT_CAPABILITY] = { .type = NLA_BINARY,
.len = NL80211_HT_CAPABILITY_LEN },
@@ -719,7 +719,7 @@ static int nl80211_send_wiphy(struct sk_buff *msg, u32 pid, u32 seq, int flags,
CMD(add_beacon, NEW_BEACON);
CMD(add_station, NEW_STATION);
CMD(add_mpath, NEW_MPATH);
- CMD(update_mesh_params, SET_MESH_PARAMS);
+ CMD(update_mesh_config, SET_MESH_CONFIG);
CMD(change_bss, SET_BSS);
CMD(auth, AUTHENTICATE);
CMD(assoc, ASSOCIATE);
@@ -2673,7 +2673,7 @@ static int nl80211_req_set_reg(struct sk_buff *skb, struct genl_info *info)
return r;
}
-static int nl80211_get_mesh_params(struct sk_buff *skb,
+static int nl80211_get_mesh_config(struct sk_buff *skb,
struct genl_info *info)
{
struct cfg80211_registered_device *rdev = info->user_ptr[0];
@@ -2688,7 +2688,7 @@ static int nl80211_get_mesh_params(struct sk_buff *skb,
if (wdev->iftype != NL80211_IFTYPE_MESH_POINT)
return -EOPNOTSUPP;
- if (!rdev->ops->get_mesh_params)
+ if (!rdev->ops->get_mesh_config)
return -EOPNOTSUPP;
wdev_lock(wdev);
@@ -2696,7 +2696,7 @@ static int nl80211_get_mesh_params(struct sk_buff *skb,
if (!wdev->mesh_id_len)
memcpy(&cur_params, &default_mesh_config, sizeof(cur_params));
else
- err = rdev->ops->get_mesh_params(&rdev->wiphy, dev,
+ err = rdev->ops->get_mesh_config(&rdev->wiphy, dev,
&cur_params);
wdev_unlock(wdev);
@@ -2708,10 +2708,10 @@ static int nl80211_get_mesh_params(struct sk_buff *skb,
if (!msg)
return -ENOMEM;
hdr = nl80211hdr_put(msg, info->snd_pid, info->snd_seq, 0,
- NL80211_CMD_GET_MESH_PARAMS);
+ NL80211_CMD_GET_MESH_CONFIG);
if (!hdr)
goto nla_put_failure;
- pinfoattr = nla_nest_start(msg, NL80211_ATTR_MESH_PARAMS);
+ pinfoattr = nla_nest_start(msg, NL80211_ATTR_MESH_CONFIG);
if (!pinfoattr)
goto nla_put_failure;
NLA_PUT_U32(msg, NL80211_ATTR_IFINDEX, dev->ifindex);
@@ -2773,7 +2773,7 @@ static const struct nla_policy nl80211_meshconf_params_policy[NL80211_MESHCONF_A
[NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME] = { .type = NLA_U16 },
};
-static int nl80211_parse_mesh_params(struct genl_info *info,
+static int nl80211_parse_mesh_config(struct genl_info *info,
struct mesh_config *cfg,
u32 *mask_out)
{
@@ -2789,10 +2789,10 @@ do {\
} while (0);\
- if (!info->attrs[NL80211_ATTR_MESH_PARAMS])
+ if (!info->attrs[NL80211_ATTR_MESH_CONFIG])
return -EINVAL;
if (nla_parse_nested(tb, NL80211_MESHCONF_ATTR_MAX,
- info->attrs[NL80211_ATTR_MESH_PARAMS],
+ info->attrs[NL80211_ATTR_MESH_CONFIG],
nl80211_meshconf_params_policy))
return -EINVAL;
@@ -2847,7 +2847,7 @@ do {\
#undef FILL_IN_MESH_PARAM_IF_SET
}
-static int nl80211_update_mesh_params(struct sk_buff *skb,
+static int nl80211_update_mesh_config(struct sk_buff *skb,
struct genl_info *info)
{
struct cfg80211_registered_device *rdev = info->user_ptr[0];
@@ -2860,10 +2860,10 @@ static int nl80211_update_mesh_params(struct sk_buff *skb,
if (wdev->iftype != NL80211_IFTYPE_MESH_POINT)
return -EOPNOTSUPP;
- if (!rdev->ops->update_mesh_params)
+ if (!rdev->ops->update_mesh_config)
return -EOPNOTSUPP;
- err = nl80211_parse_mesh_params(info, &cfg, &mask);
+ err = nl80211_parse_mesh_config(info, &cfg, &mask);
if (err)
return err;
@@ -2872,7 +2872,7 @@ static int nl80211_update_mesh_params(struct sk_buff *skb,
err = -ENOLINK;
if (!err)
- err = rdev->ops->update_mesh_params(&rdev->wiphy, dev,
+ err = rdev->ops->update_mesh_config(&rdev->wiphy, dev,
mask, &cfg);
wdev_unlock(wdev);
@@ -4672,9 +4672,9 @@ static int nl80211_join_mesh(struct sk_buff *skb, struct genl_info *info)
/* start with default */
memcpy(&cfg, &default_mesh_config, sizeof(cfg));
- if (info->attrs[NL80211_ATTR_MESH_PARAMS]) {
+ if (info->attrs[NL80211_ATTR_MESH_CONFIG]) {
/* and parse parameters if given */
- err = nl80211_parse_mesh_params(info, &cfg, NULL);
+ err = nl80211_parse_mesh_config(info, &cfg, NULL);
if (err)
return err;
}
@@ -4952,16 +4952,16 @@ static struct genl_ops nl80211_ops[] = {
.flags = GENL_ADMIN_PERM,
},
{
- .cmd = NL80211_CMD_GET_MESH_PARAMS,
- .doit = nl80211_get_mesh_params,
+ .cmd = NL80211_CMD_GET_MESH_CONFIG,
+ .doit = nl80211_get_mesh_config,
.policy = nl80211_policy,
/* can be retrieved by unprivileged users */
.internal_flags = NL80211_FLAG_NEED_NETDEV |
NL80211_FLAG_NEED_RTNL,
},
{
- .cmd = NL80211_CMD_SET_MESH_PARAMS,
- .doit = nl80211_update_mesh_params,
+ .cmd = NL80211_CMD_SET_MESH_CONFIG,
+ .doit = nl80211_update_mesh_config,
.policy = nl80211_policy,
.flags = GENL_ADMIN_PERM,
.internal_flags = NL80211_FLAG_NEED_NETDEV_UP |
--
1.7.1
^ permalink raw reply related
* [PATCH 3/3 v3] mac80211: Send mesh non-HWMP path selection frames to userspace
From: Javier Cardona @ 2010-12-17 1:37 UTC (permalink / raw)
To: John W. Linville
Cc: Javier Cardona, Steve Derosier, devel, Johannes Berg,
linux-wireless
In-Reply-To: <1292525513.3612.26.camel@jlt3.sipsolutions.net>
Let path selection frames for protocols other than HWMP be sent to
userspace via NL80211_CMD_REGISTER_FRAME. Also allow userspace to send
and receive mesh path selection frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
---
v2: - update patch description (Johannes)
- remove mesh_ids_set_default and initialize ids in start_mesh (Johannes)
- more elegant check for mesh_path_sel_is_hwmp (Johannes)
v3: - no change, just rebased
net/mac80211/cfg.c | 1 +
net/mac80211/main.c | 4 ++++
net/mac80211/mesh.c | 13 +++----------
net/mac80211/mesh.h | 7 +++++++
net/mac80211/rx.c | 5 ++++-
net/wireless/nl80211.c | 2 ++
6 files changed, 21 insertions(+), 11 deletions(-)
diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c
index ae2c712..5892b03 100644
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -1670,6 +1670,7 @@ static int ieee80211_mgmt_tx(struct wiphy *wiphy, struct net_device *dev,
case NL80211_IFTYPE_AP:
case NL80211_IFTYPE_AP_VLAN:
case NL80211_IFTYPE_P2P_GO:
+ case NL80211_IFTYPE_MESH_POINT:
if (!ieee80211_is_action(mgmt->frame_control) ||
mgmt->u.action.category == WLAN_CATEGORY_PUBLIC)
break;
diff --git a/net/mac80211/main.c b/net/mac80211/main.c
index a9454cb..bbe8e0a 100644
--- a/net/mac80211/main.c
+++ b/net/mac80211/main.c
@@ -484,6 +484,10 @@ ieee80211_default_mgmt_stypes[NUM_NL80211_IFTYPES] = {
BIT(IEEE80211_STYPE_DEAUTH >> 4) |
BIT(IEEE80211_STYPE_ACTION >> 4),
},
+ [NL80211_IFTYPE_MESH_POINT] = {
+ .tx = 0xffff,
+ .rx = BIT(IEEE80211_STYPE_ACTION >> 4),
+ },
};
struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
diff --git a/net/mac80211/mesh.c b/net/mac80211/mesh.c
index c326e00..8b5906c 100644
--- a/net/mac80211/mesh.c
+++ b/net/mac80211/mesh.c
@@ -124,15 +124,6 @@ void mesh_accept_plinks_update(struct ieee80211_sub_if_data *sdata)
ieee80211_mesh_housekeeping_timer((unsigned long) sdata);
}
-void mesh_ids_set_default(struct ieee80211_if_mesh *sta)
-{
- sta->mesh_pp_id = 0; /* HWMP */
- sta->mesh_pm_id = 0; /* Airtime */
- sta->mesh_cc_id = 0; /* Disabled */
- sta->mesh_sp_id = 0; /* Neighbor Offset */
- sta->mesh_auth_id = 0; /* Disabled */
-}
-
int mesh_rmc_init(struct ieee80211_sub_if_data *sdata)
{
int i;
@@ -525,6 +516,9 @@ void ieee80211_start_mesh(struct ieee80211_sub_if_data *sdata)
atomic_inc(&local->iff_allmultis);
ieee80211_configure_filter(local);
+ ifmsh->mesh_cc_id = 0; /* Disabled */
+ ifmsh->mesh_sp_id = 0; /* Neighbor Offset */
+ ifmsh->mesh_auth_id = 0; /* Disabled */
set_bit(MESH_WORK_HOUSEKEEPING, &ifmsh->wrkq_flags);
ieee80211_mesh_root_setup(ifmsh);
ieee80211_queue_work(&local->hw, &sdata->work);
@@ -695,7 +689,6 @@ void ieee80211_mesh_init_sdata(struct ieee80211_sub_if_data *sdata)
/* Allocate all mesh structures when creating the first mesh interface. */
if (!mesh_allocated)
ieee80211s_init();
- mesh_ids_set_default(ifmsh);
setup_timer(&ifmsh->mesh_path_timer,
ieee80211_mesh_path_timer,
(unsigned long) sdata);
diff --git a/net/mac80211/mesh.h b/net/mac80211/mesh.h
index 5b828fa..890dd19 100644
--- a/net/mac80211/mesh.h
+++ b/net/mac80211/mesh.h
@@ -284,6 +284,11 @@ static inline void mesh_path_activate(struct mesh_path *mpath)
mpath->flags |= MESH_PATH_ACTIVE | MESH_PATH_RESOLVED;
}
+static inline bool mesh_path_sel_is_hwmp(struct ieee80211_sub_if_data *sdata)
+{
+ return sdata->u.mesh.mesh_pp_id == IEEE80211_PATH_PROTOCOL_HWMP;
+}
+
#define for_each_mesh_entry(x, p, node, i) \
for (i = 0; i <= x->hash_mask; i++) \
hlist_for_each_entry_rcu(node, p, &x->hash_buckets[i], list)
@@ -304,6 +309,8 @@ static inline void ieee80211_mesh_restart(struct ieee80211_sub_if_data *sdata)
{}
static inline void mesh_plink_quiesce(struct sta_info *sta) {}
static inline void mesh_plink_restart(struct sta_info *sta) {}
+static inline bool mesh_path_sel_is_hwmp(struct ieee80211_sub_if_data *sdata)
+{ return false; }
#endif
#endif /* IEEE80211S_H */
diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c
index f39524b..cdbc824 100644
--- a/net/mac80211/rx.c
+++ b/net/mac80211/rx.c
@@ -2143,10 +2143,13 @@ ieee80211_rx_h_action(struct ieee80211_rx_data *rx)
}
break;
case WLAN_CATEGORY_MESH_PLINK:
- case WLAN_CATEGORY_MESH_PATH_SEL:
if (!ieee80211_vif_is_mesh(&sdata->vif))
break;
goto queue;
+ case WLAN_CATEGORY_MESH_PATH_SEL:
+ if (!mesh_path_sel_is_hwmp(sdata))
+ break;
+ goto queue;
}
return RX_CONTINUE;
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 356c33e..177ea21 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -4445,6 +4445,7 @@ static int nl80211_register_mgmt(struct sk_buff *skb, struct genl_info *info)
dev->ieee80211_ptr->iftype != NL80211_IFTYPE_P2P_CLIENT &&
dev->ieee80211_ptr->iftype != NL80211_IFTYPE_AP &&
dev->ieee80211_ptr->iftype != NL80211_IFTYPE_AP_VLAN &&
+ dev->ieee80211_ptr->iftype != NL80211_IFTYPE_MESH_POINT &&
dev->ieee80211_ptr->iftype != NL80211_IFTYPE_P2P_GO)
return -EOPNOTSUPP;
@@ -4485,6 +4486,7 @@ static int nl80211_tx_mgmt(struct sk_buff *skb, struct genl_info *info)
dev->ieee80211_ptr->iftype != NL80211_IFTYPE_P2P_CLIENT &&
dev->ieee80211_ptr->iftype != NL80211_IFTYPE_AP &&
dev->ieee80211_ptr->iftype != NL80211_IFTYPE_AP_VLAN &&
+ dev->ieee80211_ptr->iftype != NL80211_IFTYPE_MESH_POINT &&
dev->ieee80211_ptr->iftype != NL80211_IFTYPE_P2P_GO)
return -EOPNOTSUPP;
--
1.7.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox