xfs_check - out of memory | xfs_repair - superblock error reading

xfs_check - out of memory | xfs_repair - superblock error reading

[christian gattermair]

hi!

after a reboot of our box (debian sarge, 3ware controller, raid 5 - 3tb xfs) 
we can not mount it any more.

from syslog:

Sep 18 12:51:36 localhost kernel: SGI XFS with ACLs, security attributes, 
realtime, large block numbers, no debug enabled
Sep 18 12:51:36 localhost kernel: SGI XFS Quota Management subsystem
Sep 18 12:51:53 localhost kernel: attempt to access beyond end of device
Sep 18 12:51:53 localhost kernel: sdb1: rw=0, want=6445069056, 
limit=2150101796
Sep 18 12:51:53 localhost kernel: I/O error in filesystem ("sdb1") meta-data 
dev sdb1 block 0x18027f2ff       ("xfs_read_buf") error 5 buf count 512
Sep 18 12:51:53 localhost kernel: XFS: size check 2 failed

xfs_check fails with:

xfs_check /dev/sdb1
XFS: totally zeroed log
xfs_check: out of memory

there is a lot of space (i tryed more swap)

Mem:          1011       1006          5          0        750        111
-/+ buffers/cache:        144        867
Swap:        57812          0      57812

does xfs_check only looks at the mem or also an swap??? is there any hint to 
use the swap?

second question:

xfs_repair works but can not find any superblock. any hints?

xfs_repair /dev/sdb1
Phase 1 - find and verify superblock...
error reading superblock 11 -- seek to offset 1134332153856 failed
couldn't verify primary superblock - bad magic number !!!

attempting to find secondary superblock...
...
...
..............found candidate secondary superblock...
error reading superblock 11 -- seek to offset 1134332153856 failed
unable to verify superblock, continuing...


the whole system runs one year without any errors. only today one shutdown for 
chaning the usv ....

thanks for any hint!

with friendly greetings,

christian gattermair

Re: xfs_check - out of memory | xfs_repair - superblock error reading

[linux-xfs]

christian gattermair wrote:

> xfs_repair works but can not find any superblock. any hints?
> 
> xfs_repair /dev/sdb1
> Phase 1 - find and verify superblock...
> error reading superblock 11 -- seek to offset 1134332153856 failed
> couldn't verify primary superblock - bad magic number !!!
> 
> attempting to find secondary superblock...
> ...
> ...
> ..............found candidate secondary superblock...
> error reading superblock 11 -- seek to offset 1134332153856 failed

That's about a terabyte into your 3t fs, but you can't seek to it?  Any kernel 
messages when this happens?  What does /proc/partitions and/or parted  say about 
the size of /dev/sdb1?  Seems like maybe your device itself is not as expected.

-Eric

Re: xfs_check - out of memory | xfs_repair - superblock error reading

[christian gattermair]

hi!

thanks for all your answers


parted:

Disk geometry for /dev/sda: 0.000-3147012,000 megabytes
Disk label type: msdos
Minor    Start       End     Type      Filesystem  Flags
1          0,031 1049854,423  primary   xfs

cat /proc/partitions

  8     0 3222540288 sda
   8     1 1075050898 sda1


tw_cli (3ware raid tool)

Unit  UnitType  Status         %Cmpl  Stripe  Size(GB)  Cache  AVerify  IgnECC
------------------------------------------------------------------------------
u0    RAID-5    OK             -      64K     3073.25   ON     OFF      OFF

Port   Status           Unit   Size        Blocks        Serial
---------------------------------------------------------------
p0     OK               u0     279.46 GB   586072368     3NF04F4D
p1     OK               u0     279.46 GB   586072368     3NF09YMR
p2     OK               u0     279.46 GB   586072368     3NF0AGN2
p3     OK               u0     279.46 GB   586072368     3NF0D6ZM
p4     OK               u0     279.46 GB   586072368     3NF0BG47
p5     OK               u0     279.46 GB   586072368     3NF09YQT
p6     OK               u0     279.46 GB   586072368     3NF02SMD
p7     OK               u0     279.46 GB   586072368     3NF01YL5
p8     OK               u0     279.46 GB   586072368     3NF02J46
p9     OK               u0     279.46 GB   586072368     3NF04EYE
p10    OK               u0     279.46 GB   586072368     3NF0ECRG
p11    OK               u0     279.46 GB   586072368     3NF071X5

Name  OnlineState  BBUReady  Status    Volt     Temp     Hours  LastCapTest
---------------------------------------------------------------------------
bbu   On           Yes       OK        OK       OK       255    23-Aug-2005


dmesg:

3ware 9000 Storage Controller device driver for Linux v2.26.02.001.
ACPI: PCI interrupt 0000:04:02.0[A] -> GSI 52 (level, low) -> IRQ 185
scsi_proc_hostdir_add: proc_mkdir failed for <NULL>
3w-9xxx: scsi0: AEN: INFO (0x04:0x0055): <NULL>:.
3w-9xxx: scsi0: AEN: INFO (0x04:0x0053): <NULL>:.
scsi0 : 3ware 9000 Storage Controller
3w-9xxx: scsi0: Found a 3ware 9000 Storage Controller at 0xfeaf0000, IRQ: 185.
3w-9xxx: scsi0: Firmware FE9X 2.06.00.009, BIOS BE9X 2.03.01.051, Ports: 12.
  Vendor: AMCC      Model: 9500S-12   DISK   Rev: 2.06
  Type:   Direct-Access                      ANSI SCSI revision: 03
sda : very big device. try to use READ CAPACITY(16).
SCSI device sda: 6445080576 512-byte hdwr sectors (3299881 MB)
SCSI device sda: drive cache: write back, no read (daft)
 /dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0


what is a usv? sorry a german shurtcut. i mean ups.
no i have nothing changed on the system. normal shutdown for changing the ups 
and then boot. and know i can not mount the drive ....

yes it is the same kernel (debian 2.6.8-2-686-smp)

i have know updated xfsprogs to 2.8.11 and i get a new error message with 
xfs_check:

xfs_check /dev/sda1
XFS: Log inconsistent (didn't find previous header)
XFS: failed to find log head
ERROR: cannot find log head/tail, run xfs_repair

i will try ... and hope

with friendly greetings,

christian gattermair

Re: xfs_check - out of memory | xfs_repair - superblock error reading

[Eric Sandeen]

christian gattermair wrote:
> hi!
> 
> thanks for all your answers
> 
> 
> parted:
> 
> Disk geometry for /dev/sda: 0.000-3147012,000 megabytes
> Disk label type: msdos
> Minor    Start       End     Type      Filesystem  Flags
> 1          0,031 1049854,423  primary   xfs
> 
> cat /proc/partitions
> 
>   8     0 3222540288 sda
>    8     1 1075050898 sda1

sda1 is only 1 terabyte.  sda itself appears to be about 3 terabytes.

I think you need to sort out where your filesystem is living...

Did someone repartition sda?

>   Vendor: AMCC      Model: 9500S-12   DISK   Rev: 2.06
>   Type:   Direct-Access                      ANSI SCSI revision: 03
> sda : very big device. try to use READ CAPACITY(16).

Or perhaps this is the 2T lun problem... although you say it was working
before.  At any rate this isn't looking like an xfs problem at this
stage - your kernel thinks that your storage is smaller than you think
it is.

-Eric

> SCSI device sda: 6445080576 512-byte hdwr sectors (3299881 MB)
> SCSI device sda: drive cache: write back, no read (daft)
>  /dev/scsi/host0/bus0/target0/lun0: p1
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0

Re: xfs_check - out of memory | xfs_repair - superblock error reading

[christian gattermair]

hi!

thanks for all your answers

> > parted:
> >
> > Disk geometry for /dev/sda: 0.000-3147012,000 megabytes
> > Disk label type: msdos
> > Minor    Start       End     Type      Filesystem  Flags
> > 1          0,031 1049854,423  primary   xfs
> >
> > cat /proc/partitions
> >
> >   8     0 3222540288 sda
> >    8     1 1075050898 sda1
>
> sda1 is only 1 terabyte.  sda itself appears to be about 3 terabytes.
>
> I think you need to sort out where your filesystem is living...
>
> Did someone repartition sda?

no repartition of sda or other partitions .... sda1 was the whole space of sda 
(3t)

> >   Vendor: AMCC      Model: 9500S-12   DISK   Rev: 2.06
> >   Type:   Direct-Access                      ANSI SCSI revision: 03
> > sda : very big device. try to use READ CAPACITY(16).
>
> Or perhaps this is the 2T lun problem... although you say it was working
> before.  At any rate this isn't looking like an xfs problem at this
> stage - your kernel thinks that your storage is smaller than you think
> it is.

how can i bring back the right size? today i have compiled a 2.6.18 kernel. 
same error ....

any ideas?

thanks for help

with friendly greetings,

christian gattermair

> -Eric
>
> > SCSI device sda: 6445080576 512-byte hdwr sectors (3299881 MB)
> > SCSI device sda: drive cache: write back, no read (daft)
> >  /dev/scsi/host0/bus0/target0/lun0: p1
> > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0

Re: xfs_check - out of memory | xfs_repair - superblock error reading

[David Chinner]

On Mon, Sep 18, 2006 at 03:19:18PM +0200, christian gattermair wrote:
> hi!
> 
> after a reboot of our box (debian sarge, 3ware controller, raid 5 - 3tb xfs) 
> we can not mount it any more.
> 
> from syslog:
> 
> Sep 18 12:51:36 localhost kernel: SGI XFS with ACLs, security attributes, 
> realtime, large block numbers, no debug enabled
> Sep 18 12:51:36 localhost kernel: SGI XFS Quota Management subsystem
> Sep 18 12:51:53 localhost kernel: attempt to access beyond end of device
> Sep 18 12:51:53 localhost kernel: sdb1: rw=0, want=6445069056, 
> limit=2150101796
> Sep 18 12:51:53 localhost kernel: I/O error in filesystem ("sdb1") meta-data 
> dev sdb1 block 0x18027f2ff       ("xfs_read_buf") error 5 buf count 512
> Sep 18 12:51:53 localhost kernel: XFS: size check 2 failed

I/O error - something is not right with your raid controller i think.
Are there any other errors in dmesg? What does /proc/partitions tell
you about the size of the device?

> xfs_check fails with:
> 
> xfs_check /dev/sdb1
> XFS: totally zeroed log
> xfs_check: out of memory

3TB filesystem - you won't be able to xfs_check that on a 32 bit system,
and you'll need >6GiB RAM to check it on a 64bit system.

> there is a lot of space (i tryed more swap)
> 
> Mem:          1011       1006          5          0        750        111
> -/+ buffers/cache:        144        867
> Swap:        57812          0      57812
> 
> does xfs_check only looks at the mem or also an swap??? is there any hint to 
> use the swap?

Sounds like a 32 bit system where a process can't use more than 2-3GB of RAM.
No amount of swap will help if the process requires more then the maximum
thæt can be addressed per process.

> second question:
> 
> xfs_repair works but can not find any superblock. any hints?
> 
> xfs_repair /dev/sdb1
> Phase 1 - find and verify superblock...
> error reading superblock 11 -- seek to offset 1134332153856 failed
> couldn't verify primary superblock - bad magic number !!!

As already commented, that's about 1TB into 3TB volume. I'd suggest
raid controller problems....

Did you boot the same kernel you'd been running previously?

> the whole system runs one year without any errors. only today one shutdown for 
> chaning the usv ....

What's a usv? Did you change anything else?

Cheers,

Dave.
-- 
Dave Chinner
Principal Engineer
SGI Australian Software Group

Re: xfs_check - out of memory | xfs_repair - superblock error reading

[Stephan Jansen]

[-- Attachment #1: Type: text/plain, Size: 1623 bytes --]


Hi,


On Sep 18, 2006, at 5:23 PM, David Chinner wrote:

> On Mon, Sep 18, 2006 at 03:19:18PM +0200, christian gattermair wrote:
>> hi!
>>
>> after a reboot of our box (debian sarge, 3ware controller, raid 5  
>> - 3tb xfs)
>> we can not mount it any more.
>>
>> from syslog:
>>
>> Sep 18 12:51:36 localhost kernel: SGI XFS with ACLs, security  
>> attributes,
>> realtime, large block numbers, no debug enabled
>> Sep 18 12:51:36 localhost kernel: SGI XFS Quota Management subsystem
>> Sep 18 12:51:53 localhost kernel: attempt to access beyond end of  
>> device
>> Sep 18 12:51:53 localhost kernel: sdb1: rw=0, want=6445069056,
>> limit=2150101796
>> Sep 18 12:51:53 localhost kernel: I/O error in filesystem ("sdb1")  
>> meta-data
>> dev sdb1 block 0x18027f2ff       ("xfs_read_buf") error 5 buf  
>> count 512
>> Sep 18 12:51:53 localhost kernel: XFS: size check 2 failed
>
> I/O error - something is not right with your raid controller i think.
> Are there any other errors in dmesg? What does /proc/partitions tell
> you about the size of the device?
>
>> xfs_check fails with:
>>
>> xfs_check /dev/sdb1
>> XFS: totally zeroed log
>> xfs_check: out of memory
>
> 3TB filesystem - you won't be able to xfs_check that on a 32 bit  
> system,
> and you'll need >6GiB RAM to check it on a 64bit system.
>
>

I was just going to create a 3TB filesystem on a 32 bit system.  So
xfs_check will not work?  How about xfs_repair?  I assume that will
work but would like to know beforehand.

[stuff deleted]

> Cheers,
>
> Dave.
> -- 
> Dave Chinner
> Principal Engineer
> SGI Australian Software Group
>

--

----- Stephan


[-- Attachment #2: smime.p7s --]
[-- Type: application/pkcs7-signature, Size: 2383 bytes --]

RE: xfs_check - out of memory | xfs_repair - superblock error reading

[Barry Naujok]

 

> -----Original Message-----
> From: xfs-bounce@oss.sgi.com [mailto:xfs-bounce@oss.sgi.com] 
> On Behalf Of Stephan Jansen
> Sent: Tuesday, 19 September 2006 8:56 AM
> To: xfs@oss.sgi.com
> Subject: Re: xfs_check - out of memory | xfs_repair - 
> superblock error reading
> 
> 
> I was just going to create a 3TB filesystem on a 32 bit system.  So
> xfs_check will not work?  How about xfs_repair?  I assume that will
> work but would like to know beforehand.

Just to let you know, I'm currently working on memory optimisations for
xfs_repair and when it's released, it should work on your system. Memory
usage will grow with inode count and free space fragementation and not based
on filesystem size as it currently does.

The first set of changes have been done and are currently being tested.

Re: xfs_check - out of memory | xfs_repair - superblock error reading

[Frank Hellmann]

Hi,

Stephan Jansen wrote:
>
> Hi,
>
> I was just going to create a 3TB filesystem on a 32 bit system.  So
> xfs_check will not work?  How about xfs_repair?  I assume that will
> work but would like to know beforehand.
>
> [stuff deleted]
>
>
> ----- Stephan
>

I have a couple of 3.1TB FC arrays here and I had no real problems with
xfs on them so far. We have to reset the machines from time to time,
'cause nvidia drivers and data moving locks up the complete machine, but
even then no data losses occured. The lastest kernels we use (2.6.16)
checks the filesystems/logs without any hickups during mount phase.

Commandline xfs_check won't work (out of memory error), but checking
with xfs_repair works fine here. It will need a lot of memory though, so
have at least 3GB RAM installed.

    Cheers,
                   Frank...

-- 
--------------------------------------------------------------------------
Frank Hellmann          Optical Art GmbH           Waterloohain 7a
DI Supervisor           http://www.opticalart.de   22769 Hamburg
frank@opticalart.de     Tel: ++49 40 5111051       Fax: ++49 40 43169199 

Re: xfs_check - out of memory | xfs_repair - superblock error reading

[christian gattermair]

hi!

xfs_repair

.....................................Sorry, could not find valid secondary 
superblock
Exiting now.

data lose or any option to recover anything????

thanks for any tip or hint!

with friendly greetings,

christian gattermair