Re: [PATCH] xfs/053: test for stale data exposure via falloc/writeback interaction

[Brian Foster <bfoster@redhat.com>]

On Mon, Sep 29, 2014 at 01:32:44PM +1000, Dave Chinner wrote:
> On Fri, Sep 26, 2014 at 02:32:29PM -0400, Brian Foster wrote:
> > XFS buffered I/O writeback has a subtle race condition that leads to
> > stale data exposure if the filesystem happens to crash after delayed
> > allocation blocks are converted on disk and before data is written back
> > to said blocks.
> > 
> > Use file allocation commands to attempt to reproduce a related, but
> > slightly different variant of this problem. The associated falloc
> > commands can lead to partial writeback that converts an extent larger
> > than the range affected by falloc. If the filesystem crashes after the
> > extent conversion but before all other cached data is written to the
> > extent, stale data can be exposed.
> > 
> > Signed-off-by: Brian Foster <bfoster@redhat.com>
> > ---
> > 
> > This fell out of a combination of a conversation with Dave about XFS
> > writeback and buffer/cache coherency and some hacking I'm doing on the
> > XFS zero range implementation. Note that fpunch currently fails the
> > test. Also, this test is XFS specific primarily due to the use of
> > godown.
> .....
> > +_crashtest()
> > +{
> > +	cmd=$1
> > +	img=$SCRATCH_MNT/$seq.img
> > +	mnt=$SCRATCH_MNT/$seq.mnt
> > +	file=$mnt/file
> > +
> > +	# Create an fs on a small, initialized image. The pattern is written to
> > +	# the image to detect stale data exposure.
> > +	$XFS_IO_PROG -f -c "truncate 0" -c "pwrite 0 25M" $img \
> > +		>> $seqres.full 2>&1
> > +	$MKFS_XFS_PROG $MKFS_OPTIONS $img >> $seqres.full 2>&1
> > +
> > +	mkdir -p $mnt
> > +	mount $img $mnt
> > +
> > +	echo $cmd
> > +
> > +	# write, run the test command and shutdown the fs
> > +	$XFS_IO_PROG -f -c "pwrite -S 1 0 64k" -c "$cmd 60k 4k" $file | \
> > +		_filter_xfs_io
> 
> So at this point the file is correctly 64k in size in memory.
> 
> > +	./src/godown -f $mnt
> 
> And here you tell godown to flush the log, so if there's a
> transaction in the that sets the inode size to 64k.
> 
> > +	umount $mnt
> > +	mount $img $mnt
> 
> Then log recovery will set the file size to 64k, and:
> 
> > +
> > +	# we generally expect a zero-sized file (this should be silent)
> > +	hexdump $file
> 
> This comment is not actually correct. I'm actually seeing 64k length
> files after recovery in 2 of 3 cases being tested, so I don't think
> this is a correct observation.
> 
> Some clarification of what is actually being tested is needed
> here. 
> 

What output is dumped for the file? I normally see either a zero length
file or data that was never written to the file. For example, punch
fails with this:

+0000000 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
+*
+000f000 0000 0000 0000 0000 0000 0000 0000 0000
+*
+0010000

I suppose it could be possible to see a non-zero length file with valid
data, but I've not seen that occur.

Brian

> Cheers,
> 
> Dave.
> -- 
> Dave Chinner
> david@fromorbit.com

_______________________________________________
xfs mailing list
xfs@oss.sgi.com
http://oss.sgi.com/mailman/listinfo/xfs