public inbox for linux-xfs@vger.kernel.org
 help / color / mirror / Atom feed
From: Richard Ems <richard.ems@cape-horn-eng.com>
To: xfs@oss.sgi.com, Stan Hoeppner <stan@hardwarefreak.com>
Subject: Re: XFS unlink still slow on 3.1.9 kernel ?
Date: Tue, 14 Feb 2012 14:02:01 +0100	[thread overview]
Message-ID: <4F3A5B49.6020803@cape-horn-eng.com> (raw)

Hi Stan,

I was not subscribed to the list so I did not get your mail. I
subscribed now, but apparently and admin has to aprove the subscription
since I am not getting any confirmation email. so this will take some time.

> On 2/13/2012 10:57 AM, Richard Ems wrote:
>> The case is connected through SCSI.
> 
> Do you mean iSCSI?  Does the host on which you're running your "find
> dir" command have a 1GbE or 10GbE connection to the InforTrend unit?
> More than one connection using bonding or multipath?  Direct connected
> or through a switch(es)?  What brand is the switch(es)?  Switch(es)
> under heavy load?

NO. SCSI. Not iSCSI. No switches, it's direct attached through a LSI
SCSI Controller:

lspci shows:

LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI



> If it's a single direct 1GbE connection it's possible you're running out
> of host pipe bandwidth which is only ~100MB/s in each direction.  Check
> iotop/iostat while running your command to see if you're peaking the
> interface with either read or write bytes.  If either are at or above
> 100MB/s then your host pipe is full, thus this is a significant part of
> your high run time problem.

This does not apply, or?


> Also check the performance data in the management interface on the
> InforTrend unit to see if you're hitting any limits there (if it has
> such a feature).  RAID6 is numerically intensive and that particular
> controller may not have the ASIC horsepower to keep up with the IOPS
> workload you're throwing at it.

There is no performance data in the management interface to check.


> Lastly, please paste the exact command or script you refer to as "find
> dir" which is generating the workload in question.

See previous answers to the list. You will see all commands there.

Thanks,
Richard



-- 
Richard Ems       mail: Richard.Ems@Cape-Horn-Eng.com

Cape Horn Engineering S.L.
C/ Dr. J.J. Dómine 1, 5º piso
46011 Valencia
Tel : +34 96 3242923 / Fax 924
http://www.cape-horn-eng.com

_______________________________________________
xfs mailing list
xfs@oss.sgi.com
http://oss.sgi.com/mailman/listinfo/xfs

             reply	other threads:[~2012-02-14 13:02 UTC|newest]

Thread overview: 31+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-02-14 13:02 Richard Ems [this message]
     [not found] ` <4F3AA191.9030606@mnsu.edu>
2012-02-14 18:12   ` XFS unlink still slow on 3.1.9 kernel ? Richard Ems
2012-02-14 19:07     ` Christoph Hellwig
2012-02-15 12:48       ` Richard Ems
2012-02-14 23:10 ` Stan Hoeppner
2012-02-15 15:54   ` Richard Ems
  -- strict thread matches above, loose matches on Subject: below --
2012-02-13 16:57 Richard Ems
2012-02-13 17:08 ` Christoph Hellwig
2012-02-13 17:11   ` Richard Ems
2012-02-13 17:15     ` Christoph Hellwig
2012-02-13 17:26       ` Richard Ems
2012-02-13 17:29         ` Christoph Hellwig
2012-02-13 17:53           ` Richard Ems
2012-02-13 18:02             ` Christoph Hellwig
2012-02-13 18:06               ` Richard Ems
2012-02-13 18:10                 ` Christoph Hellwig
2012-02-13 18:18                   ` Richard Ems
2012-02-13 18:48                   ` Richard Ems
2012-02-13 21:16                     ` Christoph Hellwig
2012-02-14  5:31                       ` Stan Hoeppner
2012-02-14  9:48                       ` Richard Ems
2012-02-14 19:43                         ` Christoph Hellwig
2012-02-14  9:49                       ` Richard Ems
2012-02-14 10:54                       ` Richard Ems
2012-02-14 11:44                       ` Richard Ems
2012-02-14  0:09 ` Dave Chinner
2012-02-14 12:32   ` Richard Ems
2012-02-14 19:45     ` Christoph Hellwig
2012-02-15 12:07       ` Richard Ems
2012-02-15  1:27     ` Dave Chinner
2012-02-15 12:07       ` Richard Ems

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4F3A5B49.6020803@cape-horn-eng.com \
    --to=richard.ems@cape-horn-eng.com \
    --cc=stan@hardwarefreak.com \
    --cc=xfs@oss.sgi.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox