>>>>>>>>>>>>>>>>>>>>> Thanks in advance Haroun Ansari M A ------=_NextPart_000_0005_01C7CF80.1308DD20 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable

Hi all,

Processor (MPC8560)

Whenever reboot command is given in the = linux=20 console. The processor gets reset and it loads bootloader , kernel and = when=20 uncompressing the ramdisk it gets hang. The sample log is given below. = Any u=20 please tell me what are the factors that can makes this to = happen.

Log
----

070500 U-Boot 1.1.2 (May 30 2007 -=20 20:20:09)

Motorola PowerPC ProcessorID=3D00000000 = Rev.=20 PVR=3D80200020
Board: XXX MPC8560 [PowerQUICC=20 III]
        CPU: 660=20 MHz
        CCB: 330=20 MHz
        DDR: 165 = MHz
Performing=20 version scanning
I2C:   ready
DRAM: Configuring = UPM for=20 NAND
Configuring UPM for MSC8122 DSI Port
Initializing=20 DRAM
    DDR: 256 MB
Relocating POST = functions.
FLASH:=20 16 MB
L2 cache enabled: 256KB
In:   =20 serial
Out:   serial
Err:   = serial
Net:  =20 MOTO ENET0: PHY is Intel LXT971A (1378e2)
MOTO ENET1: PHY is Intel = LXT971A=20 (1378e2)
MOTO ENET0, MOTO ENET1
POST I: Before relocation. = <DEL> to=20 start...   1
POST II: After relocation. <DEL> to=20 start...   1
Micro Controller version 75
Hit any key to = stop=20 autoboot: 0
## Booting image at ffd00000 ...
   = Image=20 Name:   070500 Linux-cscpp
  =20 Created:      2007-05-30 14:49:24=20 UTC
   Image Type:   PowerPC Linux Kernel Image = (gzip=20 compressed)
   Data Size:    938254 Bytes = =3D 916.3=20 kB
   Load Address: 00000000
   Entry = Point: =20 00000000
   Verifying Checksum ... OK
   = Uncompressing=20 Kernel Image ... OK
## Loading RAMDisk Image at ff000000 = ...
  =20 Image Name:   070500 cscpp-REL_7_5
  =20 Created:      2007-05-30 14:51:09=20 UTC
   Image Type:   PowerPC Linux RAMDisk Image = (gzip=20 compressed)
   Data Size:    3543240 Bytes = =3D =20 3.4 MB
   Load Address: 00000000
   Entry = Point: =20 00000000
   Verifying Checksum ... OK
   = Loading=20 Ramdisk to 0fc4e000, end 0ffaf0c8 ... OK
Memory CAM mapping: = CAM0=3D256Mb,=20 CAM1=3D0Mb, CAM2=3D0Mb residual: 0Mb
Linux version = 2.4.20_mvlcge31-cscpp-7.5 (root@turing) (gcc version 3.3.1 = (MontaVista=20 3.3.1-3.0.10.0300532 2003-12-24)) #1 Wed May 30 20:14:43 IST = 2007
max_pfn =3D=20 8192
On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): = 0=20 pages.
zone(2): 0 pages.
Kernel command line: root=3D/dev/ram rw=20 console=3DttyS0,115200 ip=3Doff
OpenPIC Version 1.2 (1 CPUs and 44 = IRQ sources)=20 at fdf80000
time_init: decrementer frequency =3D 41.250000 = MHz
hr_time_init:=20 arch_to_nsec =3D 50840048, nsec_to_arch =3D 177167400
Calibrating = delay loop...=20 658.63 BogoMIPS
Memory: 253056k available (1696k kernel code, 760k = data, 68k=20 init, 0k highmem)
RMON - kernel resource monitoring
Dentry cache = hash=20 table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table = entries:=20 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 = (order:=20 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, = 65536=20 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 = bytes)
POSIX=20 conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based = upon=20 Swansea University Computer Society NET3.039
Initializing RT netlink=20 socket
LSP Revision 14
ikconfig 0.5 with = /proc/ikconfig
Starting=20 kswapd
Journalled Block Device driver loaded
JFFS version 1.0, (C) = 1999,=20 2000 Axis Communications AB
JFFS2 version 2.1. (C) 2001, 2002 = Red Hat,=20 Inc., designed by Axis Communications AB.
CPM UART driver version=20 0.01
ttyS0 on SCC1 at 0x8000, BRG1
pty: 256 Unix98 ptys=20 configured
eth0: FCC ENET Version 0.3, 02:e0:0c:80:31:03
eth0: = RMON=20 initialized
RAMDISK driver initialized: 16 RAM disks of 32768K size = 1024=20 blocksize
loop: loaded (max 8 devices)
eth1: Gianfar Ethernet = Controller=20 Version 1.0, 02:e0:0c:00:31:03
eth1: Running with NAPI = disabled
eth1:=20 64/64 RX/TX BD ring size
eth1: RMON initialized
eth2: Gianfar = Ethernet=20 Controller Version 1.0, 02:e0:0c:00:31:02
eth2: Running with NAPI=20 disabled
eth2: 64/64 RX/TX BD ring size
eth2: RMON = initialized
network=20 device driver for LKCD registered
Crash dump driver = initialized.
CSC=20 flash: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp = Extended=20 Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: = Erase=20 suspend on write enabled
Creating 7 MTD partitions on "CSC=20 flash":
0x00f80000-0x01000000 : "uboot"
0x00d00000-0x00e00000 :=20 "kernel0"
0x00e00000-0x00f00000 : "kernel1"
0x00700000-0x00d00000 = :=20 "app"
0x00000000-0x00380000 : "root0"
0x00380000-0x00700000 :=20 "root1"
0x00f00000-0x00f80000 : "env"
Creating 2 MTD partitions on = "CSC=20 NVRAM":
0x00000000-0x00010000 : "applog"
0x00010000-0x00020000 :=20 "kernellog"
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca = (Unknown NAND=20 256MiB 3,3V 16-bit)
Scanning device for bad blocks
Bad eraseblock = 1780 at=20 0x0de80000
Creating 1 MTD partitions on "NAND 256MiB 3,3V=20 16-bit":
0x00000000-0x10000000 : "NAND Partition"
NET4: Linux = TCP/IP 1.0=20 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache = hash table=20 of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established = 16384 bind=20 32768)
ip_conntrack version 2.1 (2048 buckets, 16384 max) - 296 bytes = per=20 conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix = domain=20 sockets 1.0/SMP for Linux NET4.0.
Event Broker Driver (C) 2001,2002=20 MontaVista Software (source@mvista.com)
Done = starting=20 sysfs
RAMDISK: Compressed image found at block 0
Freeing initrd = memory:=20 3460k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused = kernel=20 memory: 68k init

Welcome to Linux Group

Starting system...
Mounting /proc:=20 done.
Brining up loopback interface: done.
Mounting /tmp:=20 done.
Starting syslogd: done.
Starting klogd: done.
Starting = telnetd:=20 done.

MC-I2C DRIVER Successfully = Installed
mcc:=20 mcc_dev_siram_entries_config: siram config: start entry: 0, start = channel: 128,=20 count: 64
mcc: mcc_dev_siram_entries_config: siram config: start = entry: 128,=20 start channel: 192, count: 64
mcc: mcc_dev_iopin_init: IO port init=20 done
mcc: mcc_dev_clock_mux_init: clock mux init done 0x88
mcc:=20 mcc_dev_init: Board specific init done.
mcc: mcc_dev_init: BDs init=20 done
mcc: mcc_dev_init: global param init done
mcc: mcc_dev_init: = extra=20 channel param init done
mcc: mcc_dev_init: channel param init = done
[: 1:=20 unknown operand

DSP-7116: Driver registered.
DSP = MSC 7116=20 Driver for HDI Interface May 30 2007 20:19:35
DSP-7116: = Insmoded=20 Successfully Default Status & Control Register 426 6618

MSC8122_DSI driver registered. =
MSC8122_DSI=20 Driver for DSI Interface May 30 2007 20:19:35DSI = init...[2]
loading=20 LSCL module...May 30 2007 ,20:19:36
scc at 0x8100
sccp=20 0xd2575a20
priv size 176
dev name lscl0
scc1 clk = 0x000100b2
device=20 lscl0
lscl module loaded
Setting the LSCL address & IP=20 address
setting slot id 0x0021
bonding.c:v2.2.5 (May 22,=20 2003)
bonding_init(): eth1 primary device specified but has no effect = in=20 fault-tolerance (broadcast) mode
bond0 registered with MII link = monitoring=20 set to 200 ms, in fault-tolerance (broadcast) mode.
bond0 registered = without=20 ARP monitoring
eth1: PHY is Intel LXT971A (1378e2)
eth1: No link=20 detected
bond0: enslaving eth1 as an active interface with a down=20 link.
eth1: Auto-negotiation done
eth1: Full Duplex
eth1: Speed = 100BT
eth1: Link is up
eth2: PHY is Intel LXT971A = (1378e2)
eth2: No=20 link detected
bond0: enslaving eth2 as an active interface with a = down=20 link.
eth2: Auto-negotiation done
eth2: Full Duplex
eth2: Speed = 100BT
eth2: Link is up
Setting system time from hardware = clock.
yaffs:=20 dev is 7945 name is "1f:09"
bond0: link status definitely up for = interface=20 eth2.
bond0: link status definitely up for interface=20 eth1.
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at = 0x00000000:=20 0xd355 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not = found at=20 0x00000004: 0xcf85 instead
jffs2_scan_eraseblock(): Magic bitmask = 0x1985 not=20 found at 0x00000008: 0x435c instead
jffs2_scan_eraseblock(): Magic = bitmask=20 0x1985 not found at 0x0000000c: 0xc451 = instead
jffs2_scan_eraseblock(): Magic=20 bitmask 0x1985 not found at 0x00000010: 0xb677=20 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at=20 0x00000014: 0x15f5 instead
jffs2_scan_eraseblock(): Magic bitmask = 0x1985 not=20 found at 0x00000018: 0xfbfb instead
jffs2_scan_eraseblock(): Magic = bitmask=20 0x1985 not found at 0x0000001c: 0x4491 = instead
jffs2_scan_eraseblock(): Magic=20 bitmask 0x1985 not found at 0x00000020: 0x543a=20 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at=20 0x00000024: 0x1193 instead
Further such events for this erase block = will not=20 be printed
Cowardly refusing to erase blocks on filesystem with no = valid=20 JFFS2 nodes
empty_blocks 0, bad_blocks 0, c->nr_blocks = 16
mount:=20 Mounting /dev/mtdblock7 on /mnt/app-nvram failed: Invalid = argument
Punching=20 Microcontroller.
Creating TSI LOCK fileDone
Starting the xxx=20 agent

&nbs= p; =20 =3D=3D=3D=3D=3D=3D SYSTEM STARTED =3D=3D=3D=3D=3D=3D

System started

_____ _   _ _   =20 _      __ _       = _            =         =20
/ ____|| \ | || | | |    / /|=20 |    =20 (_)           &nbs= p;       =20
| | __ | \| || | | |   / / |=20 |      _ _ __   _   _ = __ __
| | |_ || .   || | | | / / |=20 |     | || '_ \ | | | |\ \/ /
| |__| || |\ = || |__|=20 | / /   | |____ | || | | || |_| | > < =
\_____||_|=20 \_| \____/ /_/    |______||_||_| |_| \__,_|/_/\_\

(none) login: root

BusyBox v1.1.0 (2006.03.23-09:02+0000) Built-in shell = (ash)
Enter=20 'help' for a list of built-in commands.

[root@(none) /root]# reboot

The system is going down NOW !!
Sending SIGTERM to all = processeExiting=20 Syslogd!
Sending SIGKILL to all processes.
Please stand by while = rebooting=20 the system.
Restarting systemste?

070500 U-Boot 1.1.2 (May 30 2007 - 20:20:09)

Motorola PowerPC ProcessorID=3D00000000 Rev. = PVR=3D80200020
Board: XXX=20 MPC8560 [PowerQUICC III]
        = CPU: 660=20 MHz
        CCB: 330=20 MHz
        DDR: 165 = MHz
Performing=20 version scanning
I2C:   ready
DRAM: Configuring = UPM for=20 NAND
Configuring UPM for MSC8122 DSI Port
Initializing=20 DRAM
    DDR: 256 MB
Relocating POST = functions.
FLASH:=20 16 MB
L2 cache enabled: 256KB
In:   =20 serial
Out:   serial
Err:   = serial
Net:  =20 MOTO ENET0: PHY is Intel LXT971A (1378e2)
MOTO ENET1: PHY is Intel = LXT971A=20 (1378e2)
MOTO ENET0, MOTO ENET1
POST I: Before relocation. = <DEL> to=20 start...   1
POST II: After relocation. <DEL> to=20 start...   1
Micro Controller version 75
Hit any key to = stop=20 autoboot: 0
## Booting image at ffd00000 ...
   = Image=20 Name:   070500 Linux-cscpp
  =20 Created:      2007-05-30 14:49:24=20 UTC
   Image Type:   PowerPC Linux Kernel Image = (gzip=20 compressed)
   Data Size:    938254 Bytes = =3D 916.3=20 kB
   Load Address: 00000000
   Entry = Point: =20 00000000
   Verifying Checksum ... OK
   = Uncompressing=20 Kernel Image ... OK
## Loading RAMDisk Image at ff000000 = ...
  =20 Image Name:   070500 cscpp-REL_7_5
  =20 Created:      2007-05-30 14:51:09=20 UTC
   Image Type:   PowerPC Linux RAMDisk Image = (gzip=20 compressed)
   Data Size:    3543240 Bytes = =3D =20 3.4 MB
   Load Address: 00000000
   Entry = Point: =20 00000000
   Verifying Checksum ... OK
   = Loading=20 Ramdisk to 0fc4e000, end 0ffaf0c8 ... OK
Memory CAM mapping: = CAM0=3D256Mb,=20 CAM1=3D0Mb, CAM2=3D0Mb residual: 0Mb
Linux version = 2.4.20_mvlcge31-cscpp-7.5 (root@turing) (gcc version 3.3.1 = (MontaVista=20 3.3.1-3.0.10.0300532 2003-12-24)) #1 Wed May 30 20:14:43 IST = 2007
max_pfn =3D=20 8192
On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): = 0=20 pages.
zone(2): 0 pages.
Kernel command line: root=3D/dev/ram rw=20 console=3DttyS0,115200 ip=3Doff
OpenPIC Version 1.2 (1 CPUs and 44 = IRQ sources)=20 at fdf80000
time_init: decrementer frequency =3D 41.250000 = MHz
hr_time_init:=20 arch_to_nsec =3D 50840048, nsec_to_arch =3D 177167400
Calibrating = delay loop...=20 658.63 BogoMIPS
Memory: 253056k available (1696k kernel code, 760k = data, 68k=20 init, 0k highmem)
RMON - kernel resource monitoring
Dentry cache = hash=20 table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table = entries:=20 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 = (order:=20 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, = 65536=20 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 = bytes)
POSIX=20 conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based = upon=20 Swansea University Computer Society NET3.039
Initializing RT netlink=20 socket
LSP Revision 14
ikconfig 0.5 with = /proc/ikconfig
Starting=20 kswapd
Journalled Block Device driver loaded
JFFS version 1.0, (C) = 1999,=20 2000 Axis Communications AB
JFFS2 version 2.1. (C) 2001, 2002 = Red Hat,=20 Inc., designed by Axis Communications AB.
CPM UART driver version=20 0.01
ttyS0 on SCC1 at 0x8000, BRG1
pty: 256 Unix98 ptys=20 configured
eth0: FCC ENET Version 0.3, 02:e0:0c:80:31:03
eth0: = RMON=20 initialized
RAMDISK driver initialized: 16 RAM disks of 32768K size = 1024=20 blocksize
loop: loaded (max 8 devices)
eth1: Gianfar Ethernet = Controller=20 Version 1.0, 02:e0:0c:00:31:03
eth1: Running with NAPI = disabled
eth1:=20 64/64 RX/TX BD ring size
eth1: RMON initialized
eth2: Gianfar = Ethernet=20 Controller Version 1.0, 02:e0:0c:00:31:02
eth2: Running with NAPI=20 disabled
eth2: 64/64 RX/TX BD ring size
eth2: RMON = initialized
network=20 device driver for LKCD registered
Crash dump driver = initialized.
CSC=20 flash: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp = Extended=20 Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: = Erase=20 suspend on write enabled
Creating 7 MTD partitions on "CSC=20 flash":
0x00f80000-0x01000000 : "uboot"
0x00d00000-0x00e00000 :=20 "kernel0"
0x00e00000-0x00f00000 : "kernel1"
0x00700000-0x00d00000 = :=20 "app"
0x00000000-0x00380000 : "root0"
0x00380000-0x00700000 :=20 "root1"
0x00f00000-0x00f80000 : "env"
Creating 2 MTD partitions on = "CSC=20 NVRAM":
0x00000000-0x00010000 : "applog"
0x00010000-0x00020000 :=20 "kernellog"
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca = (Unknown NAND=20 256MiB 3,3V 16-bit)
Scanning device for bad blocks
Bad eraseblock = 1780 at=20 0x0de80000
Creating 1 MTD partitions on "NAND 256MiB 3,3V=20 16-bit":
0x00000000-0x10000000 : "NAND Partition"
NET4: Linux = TCP/IP 1.0=20 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache = hash table=20 of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established = 16384 bind=20 32768)
ip_conntrack version 2.1 (2048 buckets, 16384 max) - 296 bytes = per=20 conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix = domain=20 sockets 1.0/SMP for Linux NET4.0.
Event Broker Driver (C) 2001,2002=20 MontaVista Software (source@mvista.com)
Done = starting=20 sysfs
RAMDISK: Compressed image found at block=20 0
<<<<<<<<<<<<<<<<<= <<<<<<<<<<<<<<<<<<&= lt;<<<<<<<<<<<<<<<<<&l= t;<<<<<<<<<<<<<<<<<Han= gs=20 Here>>>>>>>>>>>>>>>>>&= gt;>>>>

Thanks in advance

Haroun Ansari M A

------=_NextPart_000_0005_01C7CF80.1308DD20--