MPC8245 platform

MPC8245 platform

[siman]

Hi All:
Did anybody have MPC8245 patch on any kernel version? Please give me some
advise. Thanks.
I found the prpmc610(with mpc8245) could not be init by the Linux kernel.
Thanks.

Re: MPC8245 platform

[Daniel Ann]

You should try selecting sandpoint as your platform. That's using MPC8245.

Cheers,
Dan.

On 12/30/05, siman <siman@bsysjob.sharella.com> wrote:
> Hi All:
> Did anybody have MPC8245 patch on any kernel version? Please give me some
> advise. Thanks.
> I found the prpmc610(with mpc8245) could not be init by the Linux kernel.
> Thanks.
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>


--
Daniel

Migrate vxworks bsp to linux

[siman]

Hi All:
I have the prpmc610 borad(with MPC8245), I have the board's vxworks bsp, did
anybody have experience to migrate  from the vxworks to Linux system? I
think the main problem is initial the boards. 
Thank all.
Siman 

Re: Migrate vxworks bsp to linux

[Wolfgang Denk]

In message <001301c60ce8$7b4456a0$1200a8c0@xbh> you wrote:
>
> I have the prpmc610 borad(with MPC8245), I have the board's vxworks bsp, did
> anybody have experience to migrate  from the vxworks to Linux system? I
> think the main problem is initial the boards. 

You start porting a boot loader, like U-Boot.

Best regards,

Wolfgang Denk

-- 
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de
As far as the laws of mathematics refer  to  reality,  they  are  not
certain;  and  as  far  as  they  are  certain,  they do not refer to
reality.                                           -- Albert Einstein

Re: Migrate vxworks bsp to linux

[Esben Nielsen]

On Fri, 30 Dec 2005, Wolfgang Denk wrote:

> In message <001301c60ce8$7b4456a0$1200a8c0@xbh> you wrote:
> >
> > I have the prpmc610 borad(with MPC8245), I have the board's vxworks bsp, did
> > anybody have experience to migrate  from the vxworks to Linux system? I
> > think the main problem is initial the boards.
>
> You start porting a boot loader, like U-Boot.

To see if I could get Linux to run on our MPC5200 board I politely asked
the vxWorks bootloader to boot the Linux kernel via ftp. It worked. I used
the Denx kernel for the Lite5200. I had to compile the kernel with good
default parameters (ip address, nfsroot, serial setup etc.) as I couldn't
make the  vxWorks bootsector parse kernel parameters. It was a good and
very easy way to demonstrate that Linux could run on our board.

Esben

>
> Best regards,
>
> Wolfgang Denk
>
> --
> Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
> Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de
> As far as the laws of mathematics refer  to  reality,  they  are  not
> certain;  and  as  far  as  they  are  certain,  they do not refer to
> reality.                                           -- Albert Einstein
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>