* Problem with MPC8260 buffer descriptor
@ 2002-10-16 14:56 Dominique Letty
2002-10-16 15:15 ` Allen Curtis
0 siblings, 1 reply; 8+ messages in thread
From: Dominique Letty @ 2002-10-16 14:56 UTC (permalink / raw)
To: linuxppc-embedded
I wrote an hdlc driver for a MPC860 SCC device under Linux 2.2.x Kernel and
it works without
any problem.
Now I try to port this driver under Linux 2.4.17 Kernel for a MPC8260. I
have allocated
Buffer Descriptors in DPRAM and Data Buffers in SDRAM. When I try to send a
buffer, I fill
a data buffer and the first BD registers, I think, with the correct values.
It doesn't work
anytimes. When the buffer is transmited, the sending data are correct. The
problem seems to
come from the CPM which can't access to the BD modifications in the DPRAM.
Does anyone have already meet these problems?
Thanks
Dominique
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Problem with MPC8260 buffer descriptor
2002-10-16 14:56 Problem with MPC8260 buffer descriptor Dominique Letty
@ 2002-10-16 15:15 ` Allen Curtis
2002-10-17 7:56 ` John Nikiforos
0 siblings, 1 reply; 8+ messages in thread
From: Allen Curtis @ 2002-10-16 15:15 UTC (permalink / raw)
To: Dominique Letty, linuxppc-embedded
> Now I try to port this driver under Linux 2.4.17 Kernel for a MPC8260. I
> have allocated
> Buffer Descriptors in DPRAM and Data Buffers in SDRAM. When I try
> to send a
> buffer, I fill
> a data buffer and the first BD registers, I think, with the
> correct values.
> It doesn't work
> anytimes. When the buffer is transmited, the sending data are correct. The
> problem seems to
> come from the CPM which can't access to the BD modifications in the DPRAM.
>
> Does anyone have already meet these problems?
Would it be a problem to post your:
1. GSMRH & GSRM_L initialization
2. SCC Parameter RAM configuration
3. Location of your BDs in DPRAM
THX
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Problem with MPC8260 buffer descriptor
2002-10-16 15:15 ` Allen Curtis
@ 2002-10-17 7:56 ` John Nikiforos
2002-10-17 12:36 ` Dominique Letty
0 siblings, 1 reply; 8+ messages in thread
From: John Nikiforos @ 2002-10-17 7:56 UTC (permalink / raw)
To: acurtis, Dominique Letty, linuxppc-embedded
Is the ECE bit enabled?
(Cache coherency for the 8260, so that the
CPM wont get any stalled data)
John
--- Allen Curtis <acurtis@onz.com> έγραψε: >
> > Now I try to port this driver under Linux 2.4.17
> Kernel for a MPC8260. I
> > have allocated
> > Buffer Descriptors in DPRAM and Data Buffers in
> SDRAM. When I try
> > to send a
> > buffer, I fill
> > a data buffer and the first BD registers, I think,
> with the
> > correct values.
> > It doesn't work
> > anytimes. When the buffer is transmited, the
> sending data are correct. The
> > problem seems to
> > come from the CPM which can't access to the BD
> modifications in the DPRAM.
> >
> > Does anyone have already meet these problems?
>
> Would it be a problem to post your:
>
> 1. GSMRH & GSRM_L initialization
> 2. SCC Parameter RAM configuration
> 3. Location of your BDs in DPRAM
>
> THX
>
>
>
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Problem with MPC8260 buffer descriptor
2002-10-17 7:56 ` John Nikiforos
@ 2002-10-17 12:36 ` Dominique Letty
2002-10-17 13:50 ` John Nikiforos
0 siblings, 1 reply; 8+ messages in thread
From: Dominique Letty @ 2002-10-17 12:36 UTC (permalink / raw)
To: 'John Nikiforos'; +Cc: linuxppc-embedded
I don't find any information about this ECE bit in MPC8260UM and 603eUM.
Where can I enable it?
Thinks for your help.
Dominique
-----Message d'origine-----
De : John Nikiforos [mailto:ppclinuxuser@yahoo.gr]
Envoye : jeudi 17 octobre 2002 09:57
A : acurtis@onz.com; Dominique Letty; linuxppc-embedded@lists.linuxppc.org
Objet : RE: Problem with MPC8260 buffer descriptor
Is the ECE bit enabled?
(Cache coherency for the 8260, so that the
CPM wont get any stalled data)
John
--- Allen Curtis <acurtis@onz.com> έγραψε: >
> > Now I try to port this driver under Linux 2.4.17
> Kernel for a MPC8260. I
> > have allocated
> > Buffer Descriptors in DPRAM and Data Buffers in
> SDRAM. When I try
> > to send a
> > buffer, I fill
> > a data buffer and the first BD registers, I think,
> with the
> > correct values.
> > It doesn't work
> > anytimes. When the buffer is transmited, the
> sending data are correct. The
> > problem seems to
> > come from the CPM which can't access to the BD
> modifications in the DPRAM.
> >
> > Does anyone have already meet these problems?
>
> Would it be a problem to post your:
>
> 1. GSMRH & GSRM_L initialization
> 2. SCC Parameter RAM configuration
> 3. Location of your BDs in DPRAM
>
> THX
>
>
>
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Problem with MPC8260 buffer descriptor
2002-10-17 12:36 ` Dominique Letty
@ 2002-10-17 13:50 ` John Nikiforos
2002-10-17 14:30 ` Allen Curtis
0 siblings, 1 reply; 8+ messages in thread
From: John Nikiforos @ 2002-10-17 13:50 UTC (permalink / raw)
To: Dominique Letty; +Cc: linuxppc-embedded
I don't remember if it is called ECE or ESE.
I think it is on the HID0. But I am not sure.
I currently don't have the manual handy.
John
--- Dominique Letty <dletty@interfaceconcept.com>
έγραψε: >
> I don't find any information about this ECE bit in
> MPC8260UM and 603eUM.
> Where can I enable it?
>
> Thinks for your help.
>
> Dominique
> -----Message d'origine-----
> De : John Nikiforos [mailto:ppclinuxuser@yahoo.gr]
> Envoye : jeudi 17 octobre 2002 09:57
> A : acurtis@onz.com; Dominique Letty;
> linuxppc-embedded@lists.linuxppc.org
> Objet : RE: Problem with MPC8260 buffer descriptor
>
>
> Is the ECE bit enabled?
> (Cache coherency for the 8260, so that the
> CPM wont get any stalled data)
>
> John
>
> --- Allen Curtis <acurtis@onz.com> έγραψε: >
> > > Now I try to port this driver under Linux 2.4.17
> > Kernel for a MPC8260. I
> > > have allocated
> > > Buffer Descriptors in DPRAM and Data Buffers in
> > SDRAM. When I try
> > > to send a
> > > buffer, I fill
> > > a data buffer and the first BD registers, I
> think,
> > with the
> > > correct values.
> > > It doesn't work
> > > anytimes. When the buffer is transmited, the
> > sending data are correct. The
> > > problem seems to
> > > come from the CPM which can't access to the BD
> > modifications in the DPRAM.
> > >
> > > Does anyone have already meet these problems?
> >
> > Would it be a problem to post your:
> >
> > 1. GSMRH & GSRM_L initialization
> > 2. SCC Parameter RAM configuration
> > 3. Location of your BDs in DPRAM
> >
> > THX
> >
> >
> >
>
>
>
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Problem with MPC8260 buffer descriptor
2002-10-17 13:50 ` John Nikiforos
@ 2002-10-17 14:30 ` Allen Curtis
2002-10-17 16:54 ` Dominique Letty
0 siblings, 1 reply; 8+ messages in thread
From: Allen Curtis @ 2002-10-17 14:30 UTC (permalink / raw)
To: John Nikiforos, Dominique Letty; +Cc: linuxppc-embedded
There are 2 bits in the rfcr & tfcr fields of parameter RAM that are very
important.
1. GBL - I believe that this is the cache coherency bit you are looking for
2. DTB - this determines which RAM are the data buffers that the BD
structures point to are located
Hint, if you are using local RAM for your buffers you do not need GBL. Your
buffer descriptors must reside in DP RAM. If you want help, post the
information I requested before, otherwise this is a guessing game.
>
> I don't remember if it is called ECE or ESE.
> I think it is on the HID0. But I am not sure.
> I currently don't have the manual handy.
>
> John
>
> --- Dominique Letty <dletty@interfaceconcept.com>
> έγραψε: >
> > I don't find any information about this ECE bit in
> > MPC8260UM and 603eUM.
> > Where can I enable it?
> >
> > Thinks for your help.
> >
> > Dominique
> > -----Message d'origine-----
> > De : John Nikiforos [mailto:ppclinuxuser@yahoo.gr]
> > Envoye : jeudi 17 octobre 2002 09:57
> > A : acurtis@onz.com; Dominique Letty;
> > linuxppc-embedded@lists.linuxppc.org
> > Objet : RE: Problem with MPC8260 buffer descriptor
> >
> >
> > Is the ECE bit enabled?
> > (Cache coherency for the 8260, so that the
> > CPM wont get any stalled data)
> >
> > John
> >
> > --- Allen Curtis <acurtis@onz.com> έγραψε: >
> > > > Now I try to port this driver under Linux 2.4.17
> > > Kernel for a MPC8260. I
> > > > have allocated
> > > > Buffer Descriptors in DPRAM and Data Buffers in
> > > SDRAM. When I try
> > > > to send a
> > > > buffer, I fill
> > > > a data buffer and the first BD registers, I
> > think,
> > > with the
> > > > correct values.
> > > > It doesn't work
> > > > anytimes. When the buffer is transmited, the
> > > sending data are correct. The
> > > > problem seems to
> > > > come from the CPM which can't access to the BD
> > > modifications in the DPRAM.
> > > >
> > > > Does anyone have already meet these problems?
> > >
> > > Would it be a problem to post your:
> > >
> > > 1. GSMRH & GSRM_L initialization
> > > 2. SCC Parameter RAM configuration
> > > 3. Location of your BDs in DPRAM
> > >
> > > THX
> > >
> > >
> > >
> >
> >
> >
>
>
>
>
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Problem with MPC8260 buffer descriptor
2002-10-17 14:30 ` Allen Curtis
@ 2002-10-17 16:54 ` Dominique Letty
2002-10-17 17:08 ` Dominique Letty
0 siblings, 1 reply; 8+ messages in thread
From: Dominique Letty @ 2002-10-17 16:54 UTC (permalink / raw)
To: acurtis
Hi Allen,
You will find my SCC configuration below. I was thinking that my problem in
this driver was
cache and MMU configurations. But now, I'm not sure.
Dominique
IMAP_ADDR = 0xff000000
scc dpram = 0xff008000
scc_rbase = 0x890
scc_tbase = 0x8b0
scc_rfcr = 0x30
scc_tfcr = 0x30
scc_mrblr = 0x800
scc_rstate = 0x0
scc_idp = 0x15c006c
scc_rbptr = 0x890
scc_ibc = 0x64
scc_rxtmp = 0x0
scc_tstate = 0x0
scc_tdp = 0x161c068
scc_tbptr = 0x8b0
scc_tbc = 0x0
scc_txtmp = 0x65f00f42
scc_rcrc = 0x9a0ff0bd
scc_tcrc = 0x873759e0
c_mask = 0xdebb20e3
c_pres = 0xffffffff
disfc = 0x0
crcec = 0x0
abtsc = 0x0
nmarc = 0x0
retrc = 0x0
mflr = 0xc8
max_cnt = 0x60
rfthr = 0x1
rfcnt = 0x1
hmask = 0x0
haddr1 = 0x0
haddr2 = 0x0
haddr3 = 0x0
haddr4 = 0x0
tmp1 = 0x0
tmp_mb = 0xc8
SCC register = 0xff011a00
scc_gsmrl = 0x0
scc_gsmrh = 0x8000
scc_pmsr = 0x800
scc_todr = 0x0
scc_dsr = 0x7e7e
scc_scce = 0x0
scc_sccm = 0x1b
scc_sccs = 0x3
rx bd address = 0xff000890
tx bd address = 0xff0008b0
-----Message d'origine-----
De : Allen Curtis [mailto:acurtis@onz.com]
Envoye : jeudi 17 octobre 2002 16:31
A : John Nikiforos; Dominique Letty
Cc : linuxppc-embedded@lists.linuxppc.org
Objet : RE: Problem with MPC8260 buffer descriptor
There are 2 bits in the rfcr & tfcr fields of parameter RAM that are very
important.
1. GBL - I believe that this is the cache coherency bit you are looking for
2. DTB - this determines which RAM are the data buffers that the BD
structures point to are located
Hint, if you are using local RAM for your buffers you do not need GBL. Your
buffer descriptors must reside in DP RAM. If you want help, post the
information I requested before, otherwise this is a guessing game.
>
> I don't remember if it is called ECE or ESE.
> I think it is on the HID0. But I am not sure.
> I currently don't have the manual handy.
>
> John
>
> --- Dominique Letty <dletty@interfaceconcept.com>
> έγραψε: >
> > I don't find any information about this ECE bit in
> > MPC8260UM and 603eUM.
> > Where can I enable it?
> >
> > Thinks for your help.
> >
> > Dominique
> > -----Message d'origine-----
> > De : John Nikiforos [mailto:ppclinuxuser@yahoo.gr]
> > Envoye : jeudi 17 octobre 2002 09:57
> > A : acurtis@onz.com; Dominique Letty;
> > linuxppc-embedded@lists.linuxppc.org
> > Objet : RE: Problem with MPC8260 buffer descriptor
> >
> >
> > Is the ECE bit enabled?
> > (Cache coherency for the 8260, so that the
> > CPM wont get any stalled data)
> >
> > John
> >
> > --- Allen Curtis <acurtis@onz.com> έγραψε: >
> > > > Now I try to port this driver under Linux 2.4.17
> > > Kernel for a MPC8260. I
> > > > have allocated
> > > > Buffer Descriptors in DPRAM and Data Buffers in
> > > SDRAM. When I try
> > > > to send a
> > > > buffer, I fill
> > > > a data buffer and the first BD registers, I
> > think,
> > > with the
> > > > correct values.
> > > > It doesn't work
> > > > anytimes. When the buffer is transmited, the
> > > sending data are correct. The
> > > > problem seems to
> > > > come from the CPM which can't access to the BD
> > > modifications in the DPRAM.
> > > >
> > > > Does anyone have already meet these problems?
> > >
> > > Would it be a problem to post your:
> > >
> > > 1. GSMRH & GSRM_L initialization
> > > 2. SCC Parameter RAM configuration
> > > 3. Location of your BDs in DPRAM
> > >
> > > THX
> > >
> > >
> > >
> >
> >
> >
>
>
>
>
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Problem with MPC8260 buffer descriptor
2002-10-17 16:54 ` Dominique Letty
@ 2002-10-17 17:08 ` Dominique Letty
0 siblings, 0 replies; 8+ messages in thread
From: Dominique Letty @ 2002-10-17 17:08 UTC (permalink / raw)
To: 'Dominique Letty'; +Cc: acurtis
Sorry,
I forgot the last initialization instruction that enables reception and
transmission.
dominique
IMAP_ADDR = 0xff000000
scc dpram = 0xff008000
scc_rbase = 0x890
scc_tbase = 0x8b0
scc_rfcr = 0x30
scc_tfcr = 0x30
scc_mrblr = 0x800
scc_rstate = 0x0
scc_idp = 0x0
scc_rbptr = 0x890
scc_ibc = 0x0
scc_rxtmp = 0x0
scc_tstate = 0x0
scc_tdp = 0x0
scc_tbptr = 0x8b0
scc_tbc = 0x0
scc_txtmp = 0x0
scc_rcrc = 0x0
scc_tcrc = 0x0
c_mask = 0xdebb20e3
c_pres = 0xffffffff
disfc = 0x0
crcec = 0x0
abtsc = 0x0
nmarc = 0x0
retrc = 0x0
mflr = 0xc8
max_cnt = 0x0
rfthr = 0x1
rfcnt = 0x0
hmask = 0x0
haddr1 = 0x0
haddr2 = 0x0
haddr3 = 0x0
haddr4 = 0x0
tmp1 = 0x0
tmp_mb = 0x0
SCC register = 0xff011a00
scc_gsmrl = 0x30
scc_gsmrh = 0x8000
scc_pmsr = 0x800
scc_todr = 0x0
scc_dsr = 0x7e7e
scc_scce = 0x0
scc_sccm = 0x1b
scc_sccs = 0x2
rx bd address = 0xff000890
tx bd address = 0xff0008b0
-----Message d'origine-----
De : owner-linuxppc-embedded@lists.linuxppc.org
[mailto:owner-linuxppc-embedded@lists.linuxppc.org]De la part de Dominique
Letty
Envoye : jeudi 17 octobre 2002 18:55
A : acurtis@onz.com
Objet : RE: Problem with MPC8260 buffer descriptor
Hi Allen,
You will find my SCC configuration below. I was thinking that my problem in
this driver was
cache and MMU configurations. But now, I'm not sure.
Dominique
IMAP_ADDR = 0xff000000
scc dpram = 0xff008000
scc_rbase = 0x890
scc_tbase = 0x8b0
scc_rfcr = 0x30
scc_tfcr = 0x30
scc_mrblr = 0x800
scc_rstate = 0x0
scc_idp = 0x15c006c
scc_rbptr = 0x890
scc_ibc = 0x64
scc_rxtmp = 0x0
scc_tstate = 0x0
scc_tdp = 0x161c068
scc_tbptr = 0x8b0
scc_tbc = 0x0
scc_txtmp = 0x65f00f42
scc_rcrc = 0x9a0ff0bd
scc_tcrc = 0x873759e0
c_mask = 0xdebb20e3
c_pres = 0xffffffff
disfc = 0x0
crcec = 0x0
abtsc = 0x0
nmarc = 0x0
retrc = 0x0
mflr = 0xc8
max_cnt = 0x60
rfthr = 0x1
rfcnt = 0x1
hmask = 0x0
haddr1 = 0x0
haddr2 = 0x0
haddr3 = 0x0
haddr4 = 0x0
tmp1 = 0x0
tmp_mb = 0xc8
SCC register = 0xff011a00
scc_gsmrl = 0x0
scc_gsmrh = 0x8000
scc_pmsr = 0x800
scc_todr = 0x0
scc_dsr = 0x7e7e
scc_scce = 0x0
scc_sccm = 0x1b
scc_sccs = 0x3
rx bd address = 0xff000890
tx bd address = 0xff0008b0
-----Message d'origine-----
De : Allen Curtis [mailto:acurtis@onz.com]
Envoye : jeudi 17 octobre 2002 16:31
A : John Nikiforos; Dominique Letty
Cc : linuxppc-embedded@lists.linuxppc.org
Objet : RE: Problem with MPC8260 buffer descriptor
There are 2 bits in the rfcr & tfcr fields of parameter RAM that are very
important.
1. GBL - I believe that this is the cache coherency bit you are looking for
2. DTB - this determines which RAM are the data buffers that the BD
structures point to are located
Hint, if you are using local RAM for your buffers you do not need GBL. Your
buffer descriptors must reside in DP RAM. If you want help, post the
information I requested before, otherwise this is a guessing game.
>
> I don't remember if it is called ECE or ESE.
> I think it is on the HID0. But I am not sure.
> I currently don't have the manual handy.
>
> John
>
> --- Dominique Letty <dletty@interfaceconcept.com>
> έγραψε: >
> > I don't find any information about this ECE bit in
> > MPC8260UM and 603eUM.
> > Where can I enable it?
> >
> > Thinks for your help.
> >
> > Dominique
> > -----Message d'origine-----
> > De : John Nikiforos [mailto:ppclinuxuser@yahoo.gr]
> > Envoye : jeudi 17 octobre 2002 09:57
> > A : acurtis@onz.com; Dominique Letty;
> > linuxppc-embedded@lists.linuxppc.org
> > Objet : RE: Problem with MPC8260 buffer descriptor
> >
> >
> > Is the ECE bit enabled?
> > (Cache coherency for the 8260, so that the
> > CPM wont get any stalled data)
> >
> > John
> >
> > --- Allen Curtis <acurtis@onz.com> έγραψε: >
> > > > Now I try to port this driver under Linux 2.4.17
> > > Kernel for a MPC8260. I
> > > > have allocated
> > > > Buffer Descriptors in DPRAM and Data Buffers in
> > > SDRAM. When I try
> > > > to send a
> > > > buffer, I fill
> > > > a data buffer and the first BD registers, I
> > think,
> > > with the
> > > > correct values.
> > > > It doesn't work
> > > > anytimes. When the buffer is transmited, the
> > > sending data are correct. The
> > > > problem seems to
> > > > come from the CPM which can't access to the BD
> > > modifications in the DPRAM.
> > > >
> > > > Does anyone have already meet these problems?
> > >
> > > Would it be a problem to post your:
> > >
> > > 1. GSMRH & GSRM_L initialization
> > > 2. SCC Parameter RAM configuration
> > > 3. Location of your BDs in DPRAM
> > >
> > > THX
> > >
> > >
> > >
> >
> >
> >
>
>
>
>
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2002-10-17 17:08 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2002-10-16 14:56 Problem with MPC8260 buffer descriptor Dominique Letty
2002-10-16 15:15 ` Allen Curtis
2002-10-17 7:56 ` John Nikiforos
2002-10-17 12:36 ` Dominique Letty
2002-10-17 13:50 ` John Nikiforos
2002-10-17 14:30 ` Allen Curtis
2002-10-17 16:54 ` Dominique Letty
2002-10-17 17:08 ` Dominique Letty
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).