[PATCH v3 0/7] Add support for 750CL Holly board

[PATCH v3 0/7] Add support for 750CL Holly board

[Josh Boyer]

Hi All,

This is round 3 of the patches to support the 750CL Holly board.  I
think I've gotten all the comments from rounds 1 and 2 fixed up now.

Included are a few TSI108 ethernet and PCI cleanups that should allow
for multiplatform builds for boards that contain a TSI chipset.

Paul, I think patches 1, 2, and 3 are ready to be merged.  And unless
there are lots of comments on the rest, I'd like to get them merged for
2.6.22 as well if possible.

thx,
josh

[PATCH v3 1/7] Add tsi108_pci.h for common PCI functions

[Josh Boyer]

Add a header file for the common PCI routines used for the TSI bridge

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

---
 arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c |    5 --
 arch/powerpc/sysdev/tsi108_pci.c                  |    1 
 include/asm-powerpc/tsi108_pci.h                  |   45 ++++++++++++++++++++++
 3 files changed, 47 insertions(+), 4 deletions(-)

--- linux-2.6.orig/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c
+++ linux-2.6/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c
@@ -41,6 +41,7 @@
 #include <asm/reg.h>
 #include <mm/mmu_decl.h>
 #include "mpc7448_hpc2.h"
+#include <asm/tsi108_pci.h>
 #include <asm/tsi108_irq.h>
 #include <asm/mpic.h>
 
@@ -57,10 +58,7 @@ isa_mem_base = MPC7448_HPC2_ISA_MEM_BASE
 pci_dram_offset = MPC7448_HPC2_PCI_MEM_OFFSET;
 #endif
 
-extern int tsi108_setup_pci(struct device_node *dev);
 extern void _nmask_and_or_msr(unsigned long nmask, unsigned long or_val);
-extern void tsi108_pci_int_init(struct device_node *node);
-extern void tsi108_irq_cascade(unsigned int irq, struct irq_desc *desc);
 
 int mpc7448_hpc2_exclude_device(u_char bus, u_char devfn)
 {
@@ -210,7 +208,6 @@ static int __init mpc7448_hpc2_probe(voi
 
 static int mpc7448_machine_check_exception(struct pt_regs *regs)
 {
-	extern void tsi108_clear_pci_cfg_error(void);
 	const struct exception_table_entry *entry;
 
 	/* Are we prepared to handle this fault */
--- linux-2.6.orig/arch/powerpc/sysdev/tsi108_pci.c
+++ linux-2.6/arch/powerpc/sysdev/tsi108_pci.c
@@ -35,6 +35,7 @@
 #include <asm/machdep.h>
 #include <asm/pci-bridge.h>
 #include <asm/tsi108.h>
+#include <asm/tsi108_pci.h>
 #include <asm/tsi108_irq.h>
 #include <asm/prom.h>
 
--- /dev/null
+++ linux-2.6/include/asm-powerpc/tsi108_pci.h
@@ -0,0 +1,45 @@
+/*
+ * Copyright 2007 IBM Corp
+ *
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _ASM_PPC_TSI108_PCI_H
+#define _ASM_PPC_TSI108_PCI_H
+
+#include <asm/tsi108.h>
+
+/* Register definitions */
+#define TSI108_PCI_P2O_BAR0 (TSI108_PCI_OFFSET + 0x10)
+#define TSI108_PCI_P2O_BAR0_UPPER (TSI108_PCI_OFFSET + 0x14)
+#define TSI108_PCI_P2O_BAR2 (TSI108_PCI_OFFSET + 0x18)
+#define TSI108_PCI_P2O_BAR2_UPPER (TSI108_PCI_OFFSET + 0x1c)
+#define TSI108_PCI_P2O_PAGE_SIZES (TSI108_PCI_OFFSET + 0x4c)
+#define TSI108_PCI_PFAB_BAR0 (TSI108_PCI_OFFSET + 0x204)
+#define TSI108_PCI_PFAB_BAR0_UPPER (TSI108_PCI_OFFSET + 0x208)
+#define TSI108_PCI_PFAB_IO (TSI108_PCI_OFFSET + 0x20c)
+#define TSI108_PCI_PFAB_IO_UPPER (TSI108_PCI_OFFSET + 0x210)
+#define TSI108_PCI_PFAB_MEM32 (TSI108_PCI_OFFSET + 0x214)
+#define TSI108_PCI_PFAB_PFM3 (TSI108_PCI_OFFSET + 0x220)
+#define TSI108_PCI_PFAB_PFM4 (TSI108_PCI_OFFSET + 0x230)
+
+extern int tsi108_setup_pci(struct device_node *dev);
+extern void tsi108_pci_int_init(struct device_node *node);
+extern void tsi108_irq_cascade(unsigned int irq, struct irq_desc *desc);
+extern void tsi108_clear_pci_cfg_error(void);
+
+#endif				/*  _ASM_PPC_TSI108_PCI_H */

[PATCH v3 2/7] Generalize tsi108 PHY types

[Josh Boyer]

Add a phy_type field to the tsi108 ethernet structures to indicate which PHY
is used on a board.  This is derived from the "compatible" property in the
ethernet-phy node of the device tree.  The default remains the MV88E PHY.

Also, convert the setup code to use of_get_mac_address instead of hard coding
a lookup for the "address" property in the ethernet node.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

---
 arch/powerpc/sysdev/tsi108_dev.c |    7 +++++--
 drivers/net/tsi108_eth.c         |   12 +++++++-----
 drivers/net/tsi108_eth.h         |    9 ---------
 include/asm-powerpc/tsi108.h     |   11 +++++++++++
 4 files changed, 23 insertions(+), 16 deletions(-)

--- linux-2.6.orig/arch/powerpc/sysdev/tsi108_dev.c
+++ linux-2.6/arch/powerpc/sysdev/tsi108_dev.c
@@ -107,8 +107,9 @@ static int __init tsi108_eth_of_init(voi
 			goto err;
 		}
 
-		mac_addr = of_get_property(np, "address", NULL);
-		memcpy(tsi_eth_data.mac_addr, mac_addr, 6);
+		mac_addr = of_get_mac_address(np);
+		if (mac_addr)
+			memcpy(tsi_eth_data.mac_addr, mac_addr, 6);
 
 		ph = of_get_property(np, "phy-handle", NULL);
 		phy = of_find_node_by_phandle(*ph);
@@ -129,6 +130,8 @@ static int __init tsi108_eth_of_init(voi
 		tsi_eth_data.phyregs = res.start;
 		tsi_eth_data.phy = *phy_id;
 		tsi_eth_data.irq_num = irq_of_parse_and_map(np, 0);
+		if (of_device_is_compatible(phy, "bcm54xx"))
+			tsi_eth_data.phy_type = TSI108_PHY_BCM54XX;
 		of_node_put(phy);
 		ret =
 		    platform_device_add_data(tsi_eth_dev, &tsi_eth_data,
--- linux-2.6.orig/drivers/net/tsi108_eth.c
+++ linux-2.6/drivers/net/tsi108_eth.c
@@ -82,6 +82,7 @@ struct tsi108_prv_data {
 	unsigned int phy;		/* Index of PHY for this interface */
 	unsigned int irq_num;
 	unsigned int id;
+	unsigned int phy_type;
 
 	struct timer_list timer;/* Timer that triggers the check phy function */
 	unsigned int rxtail;	/* Next entry in rxring to read */
@@ -1256,11 +1257,11 @@ static void tsi108_init_phy(struct net_d
 	if (i == 0)
 		printk(KERN_ERR "%s function time out \n", __FUNCTION__);
 
-#if (TSI108_PHY_TYPE == PHY_BCM54XX)	/* Broadcom BCM54xx PHY */
-	tsi108_write_mii(data, 0x09, 0x0300);
-	tsi108_write_mii(data, 0x10, 0x1020);
-	tsi108_write_mii(data, 0x1c, 0x8c00);
-#endif
+	if (data->phy_type == TSI108_PHY_BCM54XX) {
+		tsi108_write_mii(data, 0x09, 0x0300);
+		tsi108_write_mii(data, 0x10, 0x1020);
+		tsi108_write_mii(data, 0x1c, 0x8c00);
+	}
 
 	tsi108_write_mii(data,
 			 MII_BMCR,
@@ -1587,6 +1588,7 @@ tsi108_init_one(struct platform_device *
 	data->mii_if.supports_gmii = mii_check_gmii_support(&data->mii_if);
 
 	data->phy = einfo->phy;
+	data->phy_type = einfo->phy_type;
 	data->irq_num = einfo->irq_num;
 	data->id = pdev->id;
 	dev->open = tsi108_open;
--- linux-2.6.orig/drivers/net/tsi108_eth.h
+++ linux-2.6/drivers/net/tsi108_eth.h
@@ -43,15 +43,6 @@
 	in_be32((data->phyregs + (offset)))
 
 /*
- * PHY Configuration Options
- *
- * NOTE: Enable set of definitions corresponding to your board type
- */
-#define PHY_MV88E	1	/* Marvel 88Exxxx PHY */
-#define PHY_BCM54XX	2	/* Broardcom BCM54xx PHY */
-#define TSI108_PHY_TYPE	PHY_MV88E
-
-/*
  * TSI108 GIGE port registers
  */
 
--- linux-2.6.orig/include/asm-powerpc/tsi108.h
+++ linux-2.6/include/asm-powerpc/tsi108.h
@@ -70,6 +70,16 @@
 
 #define TSI108_PCI_CFG_BASE_PHYS	(0xfb000000)
 #define TSI108_PCI_CFG_SIZE		(0x01000000)
+
+/*
+ * PHY Configuration Options
+ *
+ * Specify "bcm54xx" in the compatible property of your device tree phy
+ * nodes if your board uses the Broadcom PHYs
+ */
+#define TSI108_PHY_MV88E	0	/* Marvel 88Exxxx PHY */
+#define TSI108_PHY_BCM54XX	1	/* Broardcom BCM54xx PHY */
+
 /* Global variables */
 
 extern u32 tsi108_pci_cfg_base;
@@ -93,6 +103,7 @@ typedef struct {
 	u16 phy;		/* phy address */
 	u16 irq_num;		/* irq number */
 	u8 mac_addr[6];		/* phy mac address */
+	u16 phy_type;	/* type of phy on board */
 } hw_info;
 
 extern u32 get_vir_csrbase(void);

[PATCH v3 3/7] Generalize tsi108 PCI setup

[Josh Boyer]

Generalize tsi108_setup_pci to take the config space physical address as
a parameter.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

---
 arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c |    4 +++-
 arch/powerpc/sysdev/tsi108_pci.c                  |    9 +++++----
 include/asm-powerpc/tsi108.h                      |    1 -
 include/asm-powerpc/tsi108_pci.h                  |    2 +-
 4 files changed, 9 insertions(+), 7 deletions(-)

--- linux-2.6.orig/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c
+++ linux-2.6/arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c
@@ -52,6 +52,8 @@
 #define DBG(fmt...) do { } while(0)
 #endif
 
+#define MPC7448HPC2_PCI_CFG_PHYS 0xfb000000
+
 #ifndef CONFIG_PCI
 isa_io_base = MPC7448_HPC2_ISA_IO_BASE;
 isa_mem_base = MPC7448_HPC2_ISA_MEM_BASE;
@@ -79,7 +81,7 @@ static void __init mpc7448_hpc2_setup_ar
 	/* setup PCI host bridge */
 #ifdef CONFIG_PCI
 	for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
-		tsi108_setup_pci(np);
+		tsi108_setup_pci(np, MPC7448HPC2_PCI_CFG_PHYS);
 
 	ppc_md.pci_exclude_device = mpc7448_hpc2_exclude_device;
 	if (ppc_md.progress)
--- linux-2.6.orig/arch/powerpc/sysdev/tsi108_pci.c
+++ linux-2.6/arch/powerpc/sysdev/tsi108_pci.c
@@ -50,6 +50,7 @@
 	((((bus)<<16) | ((devfunc)<<8) | (offset & 0xfc)) + tsi108_pci_cfg_base)
 
 u32 tsi108_pci_cfg_base;
+static u32 tsi108_pci_cfg_phys;
 u32 tsi108_csr_vir_base;
 static struct device_node *pci_irq_node;
 static struct irq_host *pci_irq_host;
@@ -186,7 +187,7 @@ tsi108_direct_read_config(struct pci_bus
 
 void tsi108_clear_pci_cfg_error(void)
 {
-	tsi108_clear_pci_error(TSI108_PCI_CFG_BASE_PHYS);
+	tsi108_clear_pci_error(tsi108_pci_cfg_phys);
 }
 
 static struct pci_ops tsi108_direct_pci_ops = {
@@ -194,7 +195,7 @@ static struct pci_ops tsi108_direct_pci_
 	tsi108_direct_write_config
 };
 
-int __init tsi108_setup_pci(struct device_node *dev)
+int __init tsi108_setup_pci(struct device_node *dev, u32 cfg_phys)
 {
 	int len;
 	struct pci_controller *hose;
@@ -203,8 +204,8 @@ int __init tsi108_setup_pci(struct devic
 	int primary = 0, has_address = 0;
 
 	/* PCI Config mapping */
-	tsi108_pci_cfg_base = (u32)ioremap(TSI108_PCI_CFG_BASE_PHYS,
-			TSI108_PCI_CFG_SIZE);
+	tsi108_pci_cfg_base = (u32)ioremap(cfg_phys, TSI108_PCI_CFG_SIZE);
+	tsi108_pci_cfg_phys = cfg_phys;
 	DBG("TSI_PCI: %s tsi108_pci_cfg_base=0x%x\n", __FUNCTION__,
 	    tsi108_pci_cfg_base);
 
--- linux-2.6.orig/include/asm-powerpc/tsi108_pci.h
+++ linux-2.6/include/asm-powerpc/tsi108_pci.h
@@ -37,7 +37,7 @@
 #define TSI108_PCI_PFAB_PFM3 (TSI108_PCI_OFFSET + 0x220)
 #define TSI108_PCI_PFAB_PFM4 (TSI108_PCI_OFFSET + 0x230)
 
-extern int tsi108_setup_pci(struct device_node *dev);
+extern int tsi108_setup_pci(struct device_node *dev, u32 cfg_phys);
 extern void tsi108_pci_int_init(struct device_node *node);
 extern void tsi108_irq_cascade(unsigned int irq, struct irq_desc *desc);
 extern void tsi108_clear_pci_cfg_error(void);
--- linux-2.6.orig/include/asm-powerpc/tsi108.h
+++ linux-2.6/include/asm-powerpc/tsi108.h
@@ -68,7 +68,6 @@
 #define TSI108_PB_ERRCS_ES		(1 << 1)
 #define TSI108_PB_ISR_PBS_RD_ERR	(1 << 8)
 
-#define TSI108_PCI_CFG_BASE_PHYS	(0xfb000000)
 #define TSI108_PCI_CFG_SIZE		(0x01000000)
 
 /*

[PATCH v3 4/7] Add support for 750CL Holly board

[Josh Boyer]

Add PowerPC 750 Holly/Hickory platform support

Signed-off-by: Stephen Winiecki <stevewin@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
---
 arch/powerpc/Kconfig                        |    2 
 arch/powerpc/platforms/embedded6xx/Kconfig  |   14 -
 arch/powerpc/platforms/embedded6xx/Makefile |    1 
 arch/powerpc/platforms/embedded6xx/holly.c  |  316 ++++++++++++++++++++++++++++
 4 files changed, 329 insertions(+), 4 deletions(-)

--- linux-2.6.orig/arch/powerpc/Kconfig
+++ linux-2.6/arch/powerpc/Kconfig
@@ -659,7 +659,7 @@ config MCA
 config PCI
 	bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_85xx || PPC_86xx \
 		|| PPC_MPC52xx || (EMBEDDED && (PPC_PSERIES || PPC_ISERIES)) \
-		|| MPC7448HPC2 || PPC_PS3
+		|| MPC7448HPC2 || PPC_PS3 || PPC_HOLLY
 	default y if !40x && !CPM2 && !8xx && !APUS && !PPC_83xx \
 		&& !PPC_85xx && !PPC_86xx
 	default PCI_PERMEDIA if !4xx && !CPM2 && !8xx && APUS
--- linux-2.6.orig/arch/powerpc/platforms/embedded6xx/Kconfig
+++ linux-2.6/arch/powerpc/platforms/embedded6xx/Kconfig
@@ -20,16 +20,24 @@ config MPC7448HPC2
 	select TSI108_BRIDGE
 	select DEFAULT_UIMAGE
 	select PPC_UDBG_16550
-	select MPIC
-	select MPIC_WEIRD
 	help
 	  Select MPC7448HPC2 if configuring for Freescale MPC7448HPC2 (Taiga)
 	  platform
+
+config PPC_HOLLY
+	bool "PPC750GX/CL with TSI10x bridge (Hickory/Holly)"
+	select TSI108_BRIDGE
+	select PPC_UDBG_16550
+	help
+	  Select PPC_HOLLY if configuring for an IBM 750GX/CL Eval
+	  Board with TSI108/9 bridge (Hickory/Holly)
 endchoice
 
 config TSI108_BRIDGE
 	bool
-	depends on MPC7448HPC2
+	depends on MPC7448HPC2 || PPC_HOLLY
+	select MPIC
+	select MPIC_WEIRD
 	default y
 
 config MPC10X_BRIDGE
--- linux-2.6.orig/arch/powerpc/platforms/embedded6xx/Makefile
+++ linux-2.6/arch/powerpc/platforms/embedded6xx/Makefile
@@ -3,3 +3,4 @@
 #
 obj-$(CONFIG_MPC7448HPC2)	+= mpc7448_hpc2.o
 obj-$(CONFIG_LINKSTATION)	+= linkstation.o ls_uart.o
+obj-$(CONFIG_PPC_HOLLY)		+= holly.o
--- /dev/null
+++ linux-2.6/arch/powerpc/platforms/embedded6xx/holly.c
@@ -0,0 +1,316 @@
+/*
+ * Board setup routines for the IBM 750GX/CL platform w/ TSI10x bridge
+ *
+ * Copyright 2007 IBM Corporation
+ *
+ * Stephen Winiecki <stevewin@us.ibm.com>
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * Based on code from mpc7448_hpc2.c
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/ide.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_core.h>
+
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/tsi108.h>
+#include <asm/pci-bridge.h>
+#include <asm/reg.h>
+#include <mm/mmu_decl.h>
+#include <asm/tsi108_irq.h>
+#include <asm/tsi108_pci.h>
+#include <asm/mpic.h>
+#include <asm/of_platform.h>
+
+#undef DEBUG
+
+#define HOLLY_PCI_CFG_PHYS 0x7e000000
+
+int holly_exclude_device(u_char bus, u_char devfn)
+{
+	if (bus == 0 && PCI_SLOT(devfn) == 0)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	else
+		return PCIBIOS_SUCCESSFUL;
+}
+
+static void holly_remap_bridge(void)
+{
+	u32 lut_val, lut_addr;
+	int i;
+
+	printk(KERN_INFO "Remapping PCI bridge\n");
+
+	/* Re-init the PCI bridge and LUT registers to have mappings that don't
+	 * rely on PIBS
+	 */
+	lut_addr = 0x900;
+	for (i = 0; i < 31; i++) {
+		tsi108_write_reg(TSI108_PB_OFFSET + lut_addr, 0x00000201);
+		lut_addr += 4;
+		tsi108_write_reg(TSI108_PB_OFFSET + lut_addr, 0x0);
+		lut_addr += 4;
+	}
+
+	/* Reserve the last LUT entry for PCI I/O space */
+	tsi108_write_reg(TSI108_PB_OFFSET + lut_addr, 0x00000241);
+	lut_addr += 4;
+	tsi108_write_reg(TSI108_PB_OFFSET + lut_addr, 0x0);
+
+	/* Map PCI I/O space */
+	tsi108_write_reg(TSI108_PCI_PFAB_IO_UPPER, 0x0);
+	tsi108_write_reg(TSI108_PCI_PFAB_IO, 0x1);
+
+	/* Map PCI CFG space */
+	tsi108_write_reg(TSI108_PCI_PFAB_BAR0_UPPER, 0x0);
+	tsi108_write_reg(TSI108_PCI_PFAB_BAR0, 0x7c000000 | 0x01);
+
+	/* We don't need MEM32 and PRM remapping so disable them */
+	tsi108_write_reg(TSI108_PCI_PFAB_MEM32, 0x0);
+	tsi108_write_reg(TSI108_PCI_PFAB_PFM3, 0x0);
+	tsi108_write_reg(TSI108_PCI_PFAB_PFM4, 0x0);
+
+	/* Set P2O_BAR0 */
+	tsi108_write_reg(TSI108_PCI_P2O_BAR0_UPPER, 0x0);
+	tsi108_write_reg(TSI108_PCI_P2O_BAR0, 0xc0000000);
+
+	/* Init the PCI LUTs to do no remapping */
+	lut_addr = 0x500;
+	lut_val = 0x00000002;
+
+	for (i = 0; i < 32; i++) {
+		tsi108_write_reg(TSI108_PCI_OFFSET + lut_addr, lut_val);
+		lut_addr += 4;
+		tsi108_write_reg(TSI108_PCI_OFFSET + lut_addr, 0x40000000);
+		lut_addr += 4;
+		lut_val += 0x02000000;
+	}
+	tsi108_write_reg(TSI108_PCI_P2O_PAGE_SIZES, 0x00007900);
+
+	/* Set 64-bit PCI bus address for system memory */
+	tsi108_write_reg(TSI108_PCI_P2O_BAR2_UPPER, 0x0);
+	tsi108_write_reg(TSI108_PCI_P2O_BAR2, 0x0);
+}
+
+static void __init holly_setup_arch(void)
+{
+	struct device_node *cpu;
+	struct device_node *np;
+
+	if (ppc_md.progress)
+		ppc_md.progress("holly_setup_arch():set_bridge", 0);
+
+	cpu = of_find_node_by_type(NULL, "cpu");
+	if (cpu != 0) {
+		const unsigned int *fp;
+
+		fp = of_get_property(cpu, "clock-frequency", NULL);
+		if (fp != 0)
+			loops_per_jiffy = *fp / HZ;
+		else
+			loops_per_jiffy = 50000000 / HZ;
+		of_node_put(cpu);
+	}
+	tsi108_csr_vir_base = get_vir_csrbase();
+
+	/* setup PCI host bridge */
+	holly_remap_bridge();
+
+	for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
+		tsi108_setup_pci(np, HOLLY_PCI_CFG_PHYS);
+
+	ppc_md.pci_exclude_device = holly_exclude_device;
+	if (ppc_md.progress)
+		ppc_md.progress("tsi108: resources set", 0x100);
+
+	printk(KERN_INFO "PPC750GX/CL Platform\n");
+}
+
+/*
+ * Interrupt setup and service.  Interrrupts on the holly come
+ * from the four external INT pins, PCI interrupts are routed via
+ * PCI interrupt control registers, it generates internal IRQ23
+ *
+ * Interrupt routing on the Holly Board:
+ * TSI108:PB_INT[0] -> CPU0:INT#
+ * TSI108:PB_INT[1] -> CPU0:MCP#
+ * TSI108:PB_INT[2] -> N/C
+ * TSI108:PB_INT[3] -> N/C
+ */
+static void __init holly_init_IRQ(void)
+{
+	struct mpic *mpic;
+	phys_addr_t mpic_paddr = 0;
+	struct device_node *tsi_pic;
+#ifdef CONFIG_PCI
+	unsigned int cascade_pci_irq;
+	struct device_node *tsi_pci;
+	struct device_node *cascade_node = NULL;
+#endif
+
+	tsi_pic = of_find_node_by_type(NULL, "open-pic");
+	if (tsi_pic) {
+		unsigned int size;
+		const void *prop = of_get_property(tsi_pic, "reg", &size);
+		mpic_paddr = of_translate_address(tsi_pic, prop);
+	}
+
+	if (mpic_paddr == 0) {
+		printk(KERN_ERR "%s: No tsi108 PIC found !\n", __func__);
+		return;
+	}
+
+	pr_debug("%s: tsi108 pic phys_addr = 0x%x\n", __func__, (u32) mpic_paddr);
+
+	mpic = mpic_alloc(tsi_pic, mpic_paddr,
+			MPIC_PRIMARY | MPIC_BIG_ENDIAN | MPIC_WANTS_RESET |
+			MPIC_SPV_EOI | MPIC_NO_PTHROU_DIS | MPIC_REGSET_TSI108,
+			24,
+			NR_IRQS-4, /* num_sources used */
+			"Tsi108_PIC");
+
+	BUG_ON(mpic == NULL);
+
+	mpic_assign_isu(mpic, 0, mpic_paddr + 0x100);
+
+	mpic_init(mpic);
+
+#ifdef CONFIG_PCI
+	tsi_pci = of_find_node_by_type(NULL, "pci");
+	if (tsi_pci == NULL) {
+		printk(KERN_ERR "%s: No tsi108 pci node found !\n", __func__);
+		return;
+	}
+
+	cascade_node = of_find_node_by_type(NULL, "pic-router");
+	if (cascade_node == NULL) {
+		printk(KERN_ERR "%s: No tsi108 pci cascade node found !\n", __func__);
+		return;
+	}
+
+	cascade_pci_irq = irq_of_parse_and_map(tsi_pci, 0);
+	pr_debug("%s: tsi108 cascade_pci_irq = 0x%x\n", __func__, (u32) cascade_pci_irq);
+	tsi108_pci_int_init(cascade_node);
+	set_irq_data(cascade_pci_irq, mpic);
+	set_irq_chained_handler(cascade_pci_irq, tsi108_irq_cascade);
+#endif
+	/* Configure MPIC outputs to CPU0 */
+	tsi108_write_reg(TSI108_MPIC_OFFSET + 0x30c, 0);
+	of_node_put(tsi_pic);
+}
+
+void holly_show_cpuinfo(struct seq_file *m)
+{
+	seq_printf(m, "vendor\t\t: IBM\n");
+	seq_printf(m, "machine\t\t: PPC750 GX/CL\n");
+}
+
+void holly_restart(char *cmd)
+{
+	__be32 __iomem *ocn_bar1 = NULL;
+	unsigned long bar;
+	struct device_node *bridge = NULL;
+	const void *prop;
+	int size;
+	phys_addr_t addr = 0xc0000000;
+
+	local_irq_disable();
+
+	bridge = of_find_node_by_type(NULL, "tsi-bridge");
+	if (bridge) {
+		prop = of_get_property(bridge, "reg", &size);
+		addr = of_translate_address(bridge, prop);
+	}
+	addr += (TSI108_PB_OFFSET + 0x414);
+
+	ocn_bar1 = ioremap(addr, 0x4);
+
+	/* Turn on the BOOT bit so the addresses are correctly
+	 * routed to the HLP interface */
+	bar = ioread32be(ocn_bar1);
+	bar |= 2;
+	iowrite32be(bar, ocn_bar1);
+	iosync();
+
+	/* Set SRR0 to the reset vector and turn on MSR_IP */
+	mtspr(SPRN_SRR0, 0xfff00100);
+	mtspr(SPRN_SRR1, MSR_IP);
+
+	/* Do an rfi to jump back to firmware.  Somewhat evil,
+	 * but it works
+	 */
+	__asm__ __volatile__("rfi" : : : "memory");
+
+	/* Spin until reset happens.  Shouldn't really get here */
+	for (;;) ;
+}
+
+void holly_power_off(void)
+{
+	local_irq_disable();
+	/* No way to shut power off with software */
+	for (;;) ;
+}
+
+void holly_halt(void)
+{
+	holly_power_off();
+}
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init holly_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+
+	if (!of_flat_dt_is_compatible(root, "ibm,holly"))
+		return 0;
+	return 1;
+}
+
+static int ppc750_machine_check_exception(struct pt_regs *regs)
+{
+	const struct exception_table_entry *entry;
+
+	/* Are we prepared to handle this fault */
+	if ((entry = search_exception_tables(regs->nip)) != NULL) {
+		tsi108_clear_pci_cfg_error();
+		regs->msr |= MSR_RI;
+		regs->nip = entry->fixup;
+		return 1;
+	}
+	return 0;
+}
+
+define_machine(holly){
+	.name                   	= "PPC750 GX/CL TSI",
+	.probe                  	= holly_probe,
+	.setup_arch             	= holly_setup_arch,
+	.init_IRQ               	= holly_init_IRQ,
+	.show_cpuinfo           	= holly_show_cpuinfo,
+	.get_irq                	= mpic_get_irq,
+	.restart                	= holly_restart,
+	.calibrate_decr         	= generic_calibrate_decr,
+	.machine_check_exception	= ppc750_machine_check_exception,
+	.progress               	= udbg_progress,
+};

[PATCH v3 5/7] Holly defconfig

[Josh Boyer]

Holly/Hickory defconfig

Signed-off-by: Stephen Winiecki <stevewin@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
---
 arch/powerpc/configs/holly_defconfig | 1070 +++++++++++++++++++++++++++++++++++
 1 file changed, 1070 insertions(+)

--- /dev/null
+++ linux-2.6/arch/powerpc/configs/holly_defconfig
@@ -0,0 +1,1070 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.21
+# Sat May  5 11:02:35 2007
+#
+# CONFIG_PPC64 is not set
+CONFIG_PPC32=y
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+
+#
+# Processor support
+#
+CONFIG_CLASSIC32=y
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_6xx=y
+CONFIG_PPC_FPU=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+# CONFIG_ALTIVEC is not set
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_SMP is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+# CONFIG_MODULE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+# CONFIG_KMOD is not set
+
+#
+# Block layer
+#
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MULTIPLATFORM is not set
+CONFIG_EMBEDDED6xx=y
+# CONFIG_APUS is not set
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_LINKSTATION is not set
+# CONFIG_MPC7448HPC2 is not set
+CONFIG_PPC_HOLLY=y
+CONFIG_TSI108_BRIDGE=y
+CONFIG_MPIC=y
+CONFIG_MPIC_WEIRD=y
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_TAU is not set
+# CONFIG_CPM2 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SECCOMP is not set
+# CONFIG_WANT_DEVICE_TREE is not set
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_ISA_DMA=y
+# CONFIG_PPC_INDIRECT_PCI is not set
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCIEPORTBUS is not set
+# CONFIG_PCI_DEBUG is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# PCI Hotplug Support
+#
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=y
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+# CONFIG_MTD is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+# CONFIG_PNPACPI is not set
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=131072
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# Misc devices
+#
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ARCMSR is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_HPTIOP is not set
+# CONFIG_SCSI_BUSLOGIC is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_EATA is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_GDTH is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_STEX is not set
+# CONFIG_SCSI_SYM53C8XX_2 is not set
+# CONFIG_SCSI_IPR is not set
+# CONFIG_SCSI_QLOGIC_1280 is not set
+# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
+# CONFIG_SCSI_LPFC is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_NSP32 is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_ESP_CORE is not set
+# CONFIG_SCSI_SRP is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+CONFIG_ATA=y
+# CONFIG_ATA_NONSTANDARD is not set
+# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SVW is not set
+# CONFIG_ATA_PIIX is not set
+# CONFIG_SATA_MV is not set
+# CONFIG_SATA_NV is not set
+# CONFIG_PDC_ADMA is not set
+# CONFIG_SATA_QSTOR is not set
+# CONFIG_SATA_PROMISE is not set
+# CONFIG_SATA_SX4 is not set
+# CONFIG_SATA_SIL is not set
+# CONFIG_SATA_SIL24 is not set
+# CONFIG_SATA_SIS is not set
+# CONFIG_SATA_ULI is not set
+# CONFIG_SATA_VIA is not set
+# CONFIG_SATA_VITESSE is not set
+# CONFIG_SATA_INIC162X is not set
+# CONFIG_PATA_ALI is not set
+# CONFIG_PATA_AMD is not set
+# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
+# CONFIG_PATA_CMD64X is not set
+# CONFIG_PATA_CS5520 is not set
+# CONFIG_PATA_CS5530 is not set
+# CONFIG_PATA_CYPRESS is not set
+# CONFIG_PATA_EFAR is not set
+# CONFIG_ATA_GENERIC is not set
+# CONFIG_PATA_HPT366 is not set
+# CONFIG_PATA_HPT37X is not set
+# CONFIG_PATA_HPT3X2N is not set
+# CONFIG_PATA_HPT3X3 is not set
+# CONFIG_PATA_IT821X is not set
+# CONFIG_PATA_IT8213 is not set
+# CONFIG_PATA_JMICRON is not set
+# CONFIG_PATA_TRIFLEX is not set
+# CONFIG_PATA_MARVELL is not set
+# CONFIG_PATA_MPIIX is not set
+# CONFIG_PATA_OLDPIIX is not set
+# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_OPTI is not set
+# CONFIG_PATA_OPTIDMA is not set
+# CONFIG_PATA_PDC_OLD is not set
+# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RZ1000 is not set
+# CONFIG_PATA_SC1200 is not set
+# CONFIG_PATA_SERVERWORKS is not set
+# CONFIG_PATA_PDC2027X is not set
+# CONFIG_PATA_SIL680 is not set
+# CONFIG_PATA_SIS is not set
+# CONFIG_PATA_VIA is not set
+# CONFIG_PATA_WINBOND is not set
+# CONFIG_PATA_PLATFORM is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+# CONFIG_FUSION_SPI is not set
+# CONFIG_FUSION_FC is not set
+# CONFIG_FUSION_SAS is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_FIXED_PHY is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+CONFIG_NET_VENDOR_3COM=y
+CONFIG_VORTEX=y
+# CONFIG_TYPHOON is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_NET_PCI is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_TSI108_ETH=y
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_FB is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# HID Devices
+#
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
+#
+
+#
+# Real Time Clock
+#
+# CONFIG_RTC_CLASS is not set
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# Auxiliary Display support
+#
+
+#
+# Virtualization
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+# CONFIG_UCC_FAST is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+# CONFIG_KPROBES is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+CONFIG_DEBUGGER=y
+CONFIG_XMON=y
+CONFIG_XMON_DEFAULT=y
+CONFIG_XMON_DISASSEMBLY=y
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_BOOTX_TEXT is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set

[PATCH v3 6/7] Holly DTS

[Josh Boyer]

Add Holly DTS file

Signed-off-by: Stephen Winiecki <stevewin@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
---
 arch/powerpc/boot/dts/holly.dts |  198 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 198 insertions(+)

--- /dev/null
+++ linux-2.6/arch/powerpc/boot/dts/holly.dts
@@ -0,0 +1,198 @@
+/*
+ * Device Tree Source for IBM Holly (PPC 750CL with TSI controller)
+ * Copyright 2007, IBM Corporation
+ *
+ * Stephen Winiecki <stevewin@us.ibm.com>
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * To build:
+ *   dtc -I dts -O asm -o holly.S -b 0 holly.dts
+ *   dtc -I dts -O dtb -o holly.dtb -b 0 holly.dts
+ */
+
+/ {
+	model = "41K7339";
+	compatible = "ibm,holly";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells =<0>;
+		PowerPC,750CL@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <20>;
+			i-cache-line-size = <20>;
+			d-cache-size = <8000>;
+			i-cache-size = <8000>;
+			d-cache-sets = <80>;
+			i-cache-sets = <80>;
+			timebase-frequency = <2faf080>;
+			clock-frequency = <23c34600>;
+			bus-frequency = <bebc200>;
+			32-bit;
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <00000000 20000000>;
+	};
+
+  	tsi109@c0000000 {
+		device_type = "tsi-bridge";
+		compatible = "tsi-bridge";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <00000000 c0000000 00010000>;
+		reg = <c0000000 00010000>;
+
+		i2c@7000 {
+			device_type = "i2c";
+			compatible  = "tsi-i2c";
+			interrupt-parent = < &/tsi109@c0000000/pic@7400 >;
+			interrupts = <e 2>;
+			reg = <7000 400>;
+		};
+
+		mdio@6000 {
+			device_type = "mdio";
+			compatible = "tsi-ethernet";
+
+			PHY1: ethernet-phy@6000 {
+				device_type = "ethernet-phy";
+				compatible = "bcm54xx";
+				reg = <6000 50>;
+				phy-id = <1>;
+			};
+
+			PHY2: ethernet-phy@6400 {
+				device_type = "ethernet-phy";
+				compatible = "bcm54xx";
+				reg = <6000 50>;
+				phy-id = <2>;
+			};
+		};
+
+		ethernet@6200 {
+			device_type = "network";
+			compatible = "tsi-ethernet";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6000 200>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = < &/tsi109@c0000000/pic@7400 >;
+			interrupts = <10 2>;
+			phy-handle = <&PHY1>;
+		};
+
+		ethernet@6600 {
+			device_type = "network";
+			compatible = "tsi-ethernet";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6400 200>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = < &/tsi109@c0000000/pic@7400 >;
+			interrupts = <11 2>;
+			phy-handle = <&PHY2>;
+		};
+
+		serial@7808 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <7808 200>;
+			virtual-reg = <c0007808>;
+			clock-frequency = <3F9C6000>;
+			current-speed = <1c200>;
+			interrupt-parent = < &/tsi109@c0000000/pic@7400 >;
+			interrupts = <c 2>;
+		};
+
+		serial@7c08 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <7c08 200>;
+			virtual-reg = <c0007c08>;
+			clock-frequency = <3F9C6000>;
+			current-speed = <1c200>;
+			interrupt-parent = < &/tsi109@c0000000/pic@7400 >;
+			interrupts = <d 2>;
+		};
+
+	  	MPIC: pic@7400 {
+			device_type = "open-pic";
+			compatible = "chrp,open-pic";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <7400 400>;
+			big-endian;
+		};
+
+		pci@1000 {
+			device_type = "pci";
+			compatible = "tsi109";
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			reg = <1000 1000>;
+			bus-range = <0 0>;
+			/*----------------------------------------------------+
+			| PCI memory range.
+			| 01 denotes I/O space
+			| 02 denotes 32-bit memory space
+			+----------------------------------------------------*/
+			ranges = <02000000 0 40000000 40000000 0 10000000
+				  01000000 0 00000000 7e000000 0 00010000>;
+			clock-frequency = <7f28154>;
+			interrupt-parent = < &/tsi109@c0000000/pic@7400 >;
+			interrupts = <17 2>;
+			interrupt-map-mask = <f800 0 0 7>;
+			/*----------------------------------------------------+
+			| The INTA, INTB, INTC, INTD are shared.
+			+----------------------------------------------------*/
+			interrupt-map = <
+				0800 0 0 1 &RT0 24 0
+				0800 0 0 2 &RT0 25 0
+				0800 0 0 3 &RT0 26 0
+				0800 0 0 4 &RT0 27 0
+
+				1000 0 0 1 &RT0 25 0
+				1000 0 0 2 &RT0 26 0
+				1000 0 0 3 &RT0 27 0
+				1000 0 0 4 &RT0 24 0
+
+				1800 0 0 1 &RT0 26 0
+				1800 0 0 2 &RT0 27 0
+				1800 0 0 3 &RT0 24 0
+				1800 0 0 4 &RT0 25 0
+
+				2000 0 0 1 &RT0 27 0
+				2000 0 0 2 &RT0 24 0
+				2000 0 0 3 &RT0 25 0
+				2000 0 0 4 &RT0 26 0
+				>;
+
+			RT0: router@1180 {
+ 				device_type = "pic-router";
+ 				interrupt-controller;
+ 				big-endian;
+ 				clock-frequency = <0>;
+ 				#address-cells = <0>;
+ 				#interrupt-cells = <2>;
+ 				interrupts = <17 2>;
+				interrupt-parent = < &/tsi109@c0000000/pic@7400 >;
+			};
+		};
+	};
+
+	chosen {
+		linux,stdout-path = "/tsi109@c0000000/serial@7808";
+		bootargs = "console=ttyS0,115200";
+	};
+};

[PATCH v3 7/7] Holly bootwrapper

[Josh Boyer]

Add Holly/Hickory bootwrapper

Signed-off-by: Stephen Winiecki <stevewin@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
---
 arch/powerpc/boot/Makefile |    9 ++++++++-
 arch/powerpc/boot/holly.c  |   38 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 46 insertions(+), 1 deletion(-)

--- linux-2.6.orig/arch/powerpc/boot/Makefile
+++ linux-2.6/arch/powerpc/boot/Makefile
@@ -43,7 +43,7 @@ $(addprefix $(obj)/,$(zlib) main.o): $(a
 src-wlib := string.S crt0.S stdio.c main.c flatdevtree.c flatdevtree_misc.c \
 		ns16550.c serial.c simple_alloc.c div64.S util.S \
 		gunzip_util.c elf_util.c $(zlib) devtree.c
-src-plat := of.c cuboot-83xx.c cuboot-85xx.c
+src-plat := of.c cuboot-83xx.c cuboot-85xx.c holly.c
 src-boot := $(src-wlib) $(src-plat) empty.c
 
 src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -131,6 +131,7 @@ image-$(CONFIG_PPC_EFIKA)		+= zImage.chr
 image-$(CONFIG_PPC_PMAC)		+= zImage.pmac
 image-$(CONFIG_PPC_83xx)		+= cuImage.83xx
 image-$(CONFIG_PPC_85xx)		+= cuImage.85xx
+image-$(CONFIG_PPC_HOLLY)		+= zImage.holly-elf
 image-$(CONFIG_DEFAULT_UIMAGE)		+= uImage
 
 # For 32-bit powermacs, build the COFF and miboot images
@@ -161,6 +162,12 @@ $(obj)/zImage.ps3: vmlinux
 $(obj)/zImage.initrd.ps3: vmlinux
 	@echo "  WARNING zImage.initrd.ps3 not supported (yet)"
 
+$(obj)/zImage.holly-elf: vmlinux $(wrapperbits)
+	$(call if_changed,wrap,holly,$(obj)/dts/holly.dts,,)
+
+$(obj)/zImage.initrd.holly-elf: vmlinux $(wrapperbits) $(obj)/ramdisk.image.gz
+	$(call if_changed,wrap,holly,$(obj)/dts/holly.dts,,$(obj)/ramdisk.image.gz)
+
 $(obj)/uImage: vmlinux $(wrapperbits)
 	$(call if_changed,wrap,uboot)
 
--- /dev/null
+++ linux-2.6/arch/powerpc/boot/holly.c
@@ -0,0 +1,38 @@
+/*
+ * Copyright 2007 IBM Corporation
+ *
+ * Stephen Winiecki <stevewin@us.ibm.com>
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * Based on earlier code:
+ * Copyright (C) Paul Mackerras 1997.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ */
+#include <stdarg.h>
+#include <stddef.h>
+#include "types.h"
+#include "elf.h"
+#include "string.h"
+#include "stdio.h"
+#include "page.h"
+#include "ops.h"
+#include "io.h"
+
+extern char _start[];
+extern char _end[];
+extern char _dtb_start[];
+extern char _dtb_end[];
+
+BSS_STACK(4096);
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5)
+{
+	u32 heapsize = 0x8000000 - (u32)_end; /* 128M */
+
+	simple_alloc_init(_end, heapsize, 32, 64);
+	ft_init(_dtb_start, 0, 4);
+	serial_console_init();
+}

Re: [PATCH v3 6/7] Holly DTS

[Segher Boessenkool]

> Add Holly DTS file
>
> Signed-off-by: Stephen Winiecki <stevewin@us.ibm.com>
> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

Acked-by: Segher Boessenkool <segher@kernel.crashing.org>

Looks good.  Two more non-essential things:

- Did you forget the L2 cache node or do you really
   just not care about it?
- You can put an "interrupt-parent" property in the
   host bridge node instead of in all its (indirect)
   children.


Segher

Re: [PATCH v3 4/7] Add support for 750CL Holly board

[Josh Boyer]

On Mon, 2007-05-07 at 09:53 -0500, Josh Boyer wrote:
> Add PowerPC 750 Holly/Hickory platform support
> 

> +
> +#define HOLLY_PCI_CFG_PHYS 0x7e000000

FYI this is the wrong address.  Should be 0x7e000000.  It's part of the
on-going PCI debugging I'm doing so I'll be sure to correct it once I
get that figured out.

josh

Re: [PATCH v3 4/7] Add support for 750CL Holly board

[Josh Boyer]

On Mon, 2007-05-07 at 13:22 -0500, Josh Boyer wrote:
> On Mon, 2007-05-07 at 09:53 -0500, Josh Boyer wrote:
> > Add PowerPC 750 Holly/Hickory platform support
> > 
> 
> > +
> > +#define HOLLY_PCI_CFG_PHYS 0x7e000000
> 
> FYI this is the wrong address.  Should be 0x7e000000.  It's part of the

ARGH.  0x7c000000

josh