From: Zang Roy-r61911 <tie-fei.zang@freescale.com>
To: Kumar Gala <galak@kernel.crashing.org>,
Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev list <linuxppc-dev@ozlabs.org>
Subject: [PATCH 2/2] Add PCI/PCI Express node for 8544DS board]
Date: 13 Jul 2007 18:05:44 +0800 [thread overview]
Message-ID: <1184321144.30789.45.camel@localhost.localdomain> (raw)
From: Roy Zang <tie-fei.zang@freescale.com>
Add PCI/PCI Express node for 8544DS board.
---
arch/powerpc/boot/dts/mpc8544ds.dts | 211 +++++++++++++++++++++++++++++++++++
1 files changed, 211 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc8544ds.dts b/arch/powerpc/boot/dts/mpc8544ds.dts
index 43bf5c1..aab0bc6 100644
--- a/arch/powerpc/boot/dts/mpc8544ds.dts
+++ b/arch/powerpc/boot/dts/mpc8544ds.dts
@@ -143,6 +143,217 @@
fsl,has-rstcr;
};
+ pci@8000 {
+ compatible = "fsl,mpc8540-pci";
+ device_type = "pci";
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+
+ /* IDSEL 0x11 J17 Slot 1 */
+ 8800 0 0 1 &mpic 2 1
+ 8800 0 0 2 &mpic 3 1
+ 8800 0 0 3 &mpic 4 1
+ 8800 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x12 J16 Slot 2 */
+
+ 9000 0 0 1 &mpic 3 1
+ 9000 0 0 2 &mpic 4 1
+ 9000 0 0 3 &mpic 2 1
+ 9000 0 0 4 &mpic 1 1>;
+
+ interrupt-parent = <&mpic>;
+ interrupts = <18 2>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 80000000 80000000 0 10000000
+ 01000000 0 00000000 e2000000 0 00800000>;
+ clock-frequency = <3f940aa>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <8000 1000>;
+ };
+
+ pci@a000 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <a000 1000>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 90000000 90000000 0 10000000
+ 01000000 0 00000000 e2800000 0 00800000>;
+ clock-frequency = <1fca055>;
+ interrupt-parent = <&mpic>;
+ interrupts = <19 2>;
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 0 1
+ 0000 0 0 2 &mpic 1 1
+ 0000 0 0 3 &mpic 2 1
+ 0000 0 0 4 &mpic 3 1
+ >;
+ };
+
+ pci@9000 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <9000 1000>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 a0000000 a0000000 0 10000000
+ 01000000 0 00000000 e3000000 0 00800000>;
+ clock-frequency = <1fca055>;
+ interrupt-parent = <&mpic>;
+ interrupts = <1a 2>;
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 4 1
+ 0000 0 0 2 &mpic 5 1
+ 0000 0 0 3 &mpic 6 1
+ 0000 0 0 4 &mpic 7 1
+ >;
+ };
+
+ pci@b000 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <b000 1000>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 b0000000 b0000000 0 10000000
+ 01000000 0 00000000 e3800000 0 00800000>;
+ clock-frequency = <1fca055>;
+ interrupt-parent = <&mpic>;
+ interrupts = <1b 2>;
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+
+ // IDSEL 0x1a
+ d000 0 0 1 &i8259 6 2
+ d000 0 0 2 &i8259 3 2
+ d000 0 0 3 &i8259 4 2
+ d000 0 0 4 &i8259 5 2
+
+ // IDSEL 0x1b
+ d800 0 0 1 &i8259 5 2
+ d800 0 0 2 &i8259 0 0
+ d800 0 0 3 &i8259 0 0
+ d800 0 0 4 &i8259 0 0
+
+ // IDSEL 0x1c USB
+ e000 0 0 1 &i8259 9 2
+ e000 0 0 2 &i8259 a 2
+ e000 0 0 3 &i8259 c 2
+ e000 0 0 4 &i8259 7 2
+
+ // IDSEL 0x1d Audio
+ e800 0 0 1 &i8259 9 2
+ e800 0 0 2 &i8259 a 2
+ e800 0 0 3 &i8259 b 2
+ e800 0 0 4 &i8259 0 0
+
+ // IDSEL 0x1e Legacy
+ f000 0 0 1 &i8259 c 2
+ f000 0 0 2 &i8259 0 0
+ f000 0 0 3 &i8259 0 0
+ f000 0 0 4 &i8259 0 0
+
+ // IDSEL 0x1f IDE/SATA
+ f800 0 0 1 &i8259 6 2
+ f800 0 0 2 &i8259 0 0
+ f800 0 0 3 &i8259 0 0
+ f800 0 0 4 &i8259 0 0
+ >;
+ uli1575@0 {
+ reg = <0 0 0 0 0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ ranges = <02000000 0 a0000000
+ 02000000 0 a0000000
+ 0 10000000
+ 01000000 0 00000000
+ 01000000 0 00000000
+ 0 00080000>;
+
+ pci_bridge@0 {
+ reg = <0 0 0 0 0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ ranges = <02000000 0 80000000
+ 02000000 0 80000000
+ 0 20000000
+ 01000000 0 00000000
+ 01000000 0 00000000
+ 0 00100000>;
+
+ isa@1e {
+ device_type = "isa";
+ #interrupt-cells = <2>;
+ #size-cells = <1>;
+ #address-cells = <2>;
+ reg = <f000 0 0 0 0>;
+ ranges = <1 0 01000000 0 0
+ 00001000>;
+ interrupt-parent = <&i8259>;
+
+ i8259: interrupt-controller@20 {
+ reg = <1 20 2
+ 1 a0 2
+ 1 4d0 2>;
+ clock-frequency = <0>;
+ interrupt-controller;
+ device_type = "interrupt-controller";
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ built-in;
+ compatible = "chrp,iic";
+ interrupts = <9 2>;
+ interrupt-parent =
+ <&mpic>;
+ };
+
+ i8042@60 {
+ #size-cells = <0>;
+ #address-cells = <1>;
+ reg = <1 60 1 1 64 1>;
+ interrupts = <1 3 c 3>;
+ interrupt-parent =
+ <&i8259>;
+
+ keyboard@0 {
+ reg = <0>;
+ compatible = "pnpPNP,303";
+ };
+
+ mouse@1 {
+ reg = <1>;
+ compatible = "pnpPNP,f03";
+ };
+ };
+
+ rtc@70 {
+ compatible =
+ "pnpPNP,b00";
+ reg = <1 70 2>;
+ };
+
+ gpio@400 {
+ reg = <1 400 80>;
+ };
+ };
+ };
+ };
+
+ };
+
mpic: pic@40000 {
clock-frequency = <0>;
interrupt-controller;
--
1.5.1
next reply other threads:[~2007-07-13 10:06 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-07-13 10:05 Zang Roy-r61911 [this message]
2007-07-16 17:12 ` [PATCH 2/2] Add PCI/PCI Express node for 8544DS board] Segher Boessenkool
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1184321144.30789.45.camel@localhost.localdomain \
--to=tie-fei.zang@freescale.com \
--cc=galak@kernel.crashing.org \
--cc=linuxppc-dev@ozlabs.org \
--cc=paulus@samba.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).