[PATCH 0/10] Support for SBC834x/8548/8560 Wind River Boards

[PATCH 0/10] Support for SBC834x/8548/8560 Wind River Boards

[Paul Gortmaker]

This series contains the patches for the Wind River SBC834x, SBC8548 and
SBC8560, grouped together for merge convenience.

Changes since previous:

sbc834x:
	- machine_device_initcall as per Kumar's recent commit 6392f184
	- remove four device_type from dts that DavidG wanted gone.
	- add of_node_put() and __initdata as per StephenR's suggestions.

sbc8548:
	- fold the dts, and conversion to dts-v1, into a single commit

sbc8560:
	- dts has localbus with 2 address cells (chipsel) and epld as child
	- UART detection legacy_serial patch separated out from 8560 patches
	- fold the dts, and conversion to dts-v1, into a single commit

I've boot tested these all on "for-2.6.25" to make sure things are sane.
Thanks again to those who have suggested improvements and changes.

Paul.

[PATCH 1/10] sbc8560: add support for Wind River SBC8560 in arch/powerpc

[Paul Gortmaker]

This adds support for the Wind River SBC8560 board, implemented as
powerpc.  It closely follows the implementation of the MPC8560ADS.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/platforms/85xx/Kconfig   |   11 +-
 arch/powerpc/platforms/85xx/Makefile  |    1 +
 arch/powerpc/platforms/85xx/sbc8560.c |  285 +++++++++++++++++++++++++++++++++
 3 files changed, 295 insertions(+), 2 deletions(-)

diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 7748a3a..0eb497b 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -38,6 +38,13 @@ config MPC85xx_DS
 	help
 	  This option enables support for the MPC85xx DS (MPC8544 DS) board
 
+config SBC8560
+	bool "Wind River SBC8560"
+	select DEFAULT_UIMAGE
+	select PPC_CPM_NEW_BINDING
+	help
+	  This option enables support for the Wind River SBC8560 board
+
 endchoice
 
 config MPC8540
@@ -49,7 +56,7 @@ config MPC8540
 config MPC8560
 	bool
 	select CPM2
-	default y if MPC8560_ADS
+	default y if MPC8560_ADS || SBC8560
 
 config MPC85xx
 	bool
@@ -59,4 +66,4 @@ config MPC85xx
 	select FSL_PCI if PCI
 	select SERIAL_8250_SHARE_IRQ if SERIAL_8250
 	default y if MPC8540_ADS || MPC85xx_CDS || MPC8560_ADS \
-		|| MPC85xx_MDS || MPC85xx_DS
+		|| MPC85xx_MDS || MPC85xx_DS || SBC8560
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index 5eca920..c3f4d01 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -6,3 +6,4 @@ obj-$(CONFIG_MPC8560_ADS) += mpc85xx_ads.o
 obj-$(CONFIG_MPC85xx_CDS) += mpc85xx_cds.o
 obj-$(CONFIG_MPC85xx_DS)  += mpc85xx_ds.o
 obj-$(CONFIG_MPC85xx_MDS) += mpc85xx_mds.o
+obj-$(CONFIG_SBC8560) += sbc8560.o
diff --git a/arch/powerpc/platforms/85xx/sbc8560.c b/arch/powerpc/platforms/85xx/sbc8560.c
new file mode 100644
index 0000000..e2bc368
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/sbc8560.c
@@ -0,0 +1,285 @@
+/*
+ * Wind River SBC8560 setup and early boot code.
+ *
+ * Copyright 2007 Wind River Systems Inc.
+ *
+ * By Paul Gortmaker (see MAINTAINERS for contact information)
+ *
+ * Based largely on the MPC8560ADS support - Copyright 2005 Freescale Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/of_platform.h>
+
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <asm/mpic.h>
+#include <mm/mmu_decl.h>
+#include <asm/udbg.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#ifdef CONFIG_CPM2
+#include <asm/cpm2.h>
+#include <sysdev/cpm2_pic.h>
+#endif
+
+#ifdef CONFIG_CPM2
+
+static void cpm2_cascade(unsigned int irq, struct irq_desc *desc)
+{
+	int cascade_irq;
+
+	while ((cascade_irq = cpm2_get_irq()) >= 0)
+		generic_handle_irq(cascade_irq);
+
+	desc->chip->eoi(irq);
+}
+
+#endif /* CONFIG_CPM2 */
+
+static void __init sbc8560_pic_init(void)
+{
+	struct mpic *mpic;
+	struct resource r;
+	struct device_node *np = NULL;
+#ifdef CONFIG_CPM2
+	int irq;
+#endif
+
+	np = of_find_node_by_type(np, "open-pic");
+	if (!np) {
+		printk(KERN_ERR "Could not find open-pic node\n");
+		return;
+	}
+
+	if (of_address_to_resource(np, 0, &r)) {
+		printk(KERN_ERR "Could not map mpic register space\n");
+		of_node_put(np);
+		return;
+	}
+
+	mpic = mpic_alloc(np, r.start,
+			MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN,
+			0, 256, " OpenPIC  ");
+	BUG_ON(mpic == NULL);
+	of_node_put(np);
+
+	mpic_init(mpic);
+
+#ifdef CONFIG_CPM2
+	/* Setup CPM2 PIC */
+	np = of_find_compatible_node(NULL, NULL, "fsl,cpm2-pic");
+	if (np == NULL) {
+		printk(KERN_ERR "PIC init: can not find fsl,cpm2-pic node\n");
+		return;
+	}
+	irq = irq_of_parse_and_map(np, 0);
+
+	cpm2_pic_init(np);
+	of_node_put(np);
+	set_irq_chained_handler(irq, cpm2_cascade);
+#endif
+}
+
+/*
+ * Setup the architecture
+ */
+#ifdef CONFIG_CPM2
+struct cpm_pin {
+	int port, pin, flags;
+};
+
+static const struct cpm_pin sbc8560_pins[] = {
+	/* SCC1 */
+	{3, 29, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{3, 30, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+	{3, 31, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+	/* SCC2 */
+	{3, 26, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{3, 27, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{3, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+
+	/* FCC2 */
+	{1, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 20, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 21, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 22, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 23, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 24, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 25, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 26, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 27, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 29, CPM_PIN_OUTPUT | CPM_PIN_SECONDARY},
+	{1, 30, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 31, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{2, 18, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK14 */
+	{2, 19, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK13 */
+
+	/* FCC3 */
+	{1, 4, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 5, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 6, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 7, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 8, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 9, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 10, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 11, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 12, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 13, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 14, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 15, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
+	{1, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{1, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+	{2, 16, CPM_PIN_INPUT | CPM_PIN_SECONDARY}, /* CLK16 */
+	{2, 17, CPM_PIN_INPUT | CPM_PIN_SECONDARY}, /* CLK15 */
+};
+
+static void __init init_ioports(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(sbc8560_pins); i++) {
+		struct cpm_pin *pin = &sbc8560_pins[i];
+		cpm2_set_pin(pin->port, pin->pin, pin->flags);
+	}
+
+	cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_RX);
+	cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_TX);
+	cpm2_clk_setup(CPM_CLK_SCC2, CPM_BRG2, CPM_CLK_RX);
+	cpm2_clk_setup(CPM_CLK_SCC2, CPM_BRG2, CPM_CLK_TX);
+	cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK13, CPM_CLK_RX);
+	cpm2_clk_setup(CPM_CLK_FCC2, CPM_CLK14, CPM_CLK_TX);
+	cpm2_clk_setup(CPM_CLK_FCC3, CPM_CLK15, CPM_CLK_RX);
+	cpm2_clk_setup(CPM_CLK_FCC3, CPM_CLK16, CPM_CLK_TX);
+}
+#endif
+
+static void __init sbc8560_setup_arch(void)
+{
+#ifdef CONFIG_PCI
+	struct device_node *np;
+#endif
+
+	if (ppc_md.progress)
+		ppc_md.progress("sbc8560_setup_arch()", 0);
+
+#ifdef CONFIG_CPM2
+	cpm2_reset();
+	init_ioports();
+#endif
+
+#ifdef CONFIG_PCI
+	for_each_compatible_node(np, "pci", "fsl,mpc8540-pci")
+		fsl_add_bridge(np, 1);
+#endif
+}
+
+static void sbc8560_show_cpuinfo(struct seq_file *m)
+{
+	uint pvid, svid, phid1;
+	uint memsize = total_memory;
+
+	pvid = mfspr(SPRN_PVR);
+	svid = mfspr(SPRN_SVR);
+
+	seq_printf(m, "Vendor\t\t: Wind River\n");
+	seq_printf(m, "Machine\t\t: SBC8560\n");
+	seq_printf(m, "PVR\t\t: 0x%x\n", pvid);
+	seq_printf(m, "SVR\t\t: 0x%x\n", svid);
+
+	/* Display cpu Pll setting */
+	phid1 = mfspr(SPRN_HID1);
+	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
+
+	/* Display the amount of memory */
+	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
+}
+
+static struct of_device_id __initdata of_bus_ids[] = {
+	{ .name = "soc", },
+	{ .type = "soc", },
+	{ .name = "cpm", },
+	{ .name = "localbus", },
+	{},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+	if (!machine_is(sbc8560))
+		return 0;
+
+	of_platform_bus_probe(NULL, of_bus_ids, NULL);
+	return 0;
+}
+device_initcall(declare_of_platform_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init sbc8560_probe(void)
+{
+        unsigned long root = of_get_flat_dt_root();
+
+        return of_flat_dt_is_compatible(root, "SBC8560");
+}
+
+#ifdef CONFIG_RTC_DRV_M48T59
+static int __init sbc8560_rtc_init(void)
+{
+	struct device_node *np;
+	struct resource res;
+	struct platform_device *rtc_dev;
+
+	np = of_find_compatible_node(NULL, NULL, "m48t59");
+	if (np == NULL) {
+		printk("No RTC in DTB. Has it been eaten by wild dogs?\n");
+		return -ENODEV;
+	}
+
+	of_address_to_resource(np, 0, &res);
+	of_node_put(np);
+
+	printk("Found RTC (m48t59) at i/o 0x%x\n", res.start);
+
+	rtc_dev = platform_device_register_simple("rtc-m48t59", 0, &res, 1);
+
+	if (IS_ERR(rtc_dev)) {
+		printk("Registering sbc8560 RTC device failed\n");
+		return PTR_ERR(rtc_dev);
+	}
+
+	return 0;
+}
+
+arch_initcall(sbc8560_rtc_init);
+
+#endif	/* M48T59 */
+
+define_machine(sbc8560) {
+	.name			= "SBC8560",
+	.probe			= sbc8560_probe,
+	.setup_arch		= sbc8560_setup_arch,
+	.init_IRQ		= sbc8560_pic_init,
+	.show_cpuinfo		= sbc8560_show_cpuinfo,
+	.get_irq		= mpic_get_irq,
+	.restart		= fsl_rstcr_restart,
+	.calibrate_decr		= generic_calibrate_decr,
+	.progress		= udbg_progress,
+};
-- 
1.5.0.rc1.gf4b6c

[PATCH 2/10] sbc8560: Add v1 device tree source for Wind River SBC8560 board

[Paul Gortmaker]

This adds a v1 device tree source for the Wind River SBC8560 board.  The
biggest difference between this and the MPC8560ADS reference platform
dts is the use of an external 16550 compatible UART instead of the CPM2.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/boot/dts/sbc8560.dts |  330 +++++++++++++++++++++++++++++++++++++
 1 files changed, 330 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/boot/dts/sbc8560.dts b/arch/powerpc/boot/dts/sbc8560.dts
new file mode 100644
index 0000000..0476802
--- /dev/null
+++ b/arch/powerpc/boot/dts/sbc8560.dts
@@ -0,0 +1,330 @@
+/*
+ * SBC8560 Device Tree Source
+ *
+ * Copyright 2007 Wind River Systems Inc.
+ *
+ * Paul Gortmaker (see MAINTAINERS for contact information)
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+	model = "SBC8560";
+	compatible = "SBC8560";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		ethernet3 = &enet3;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		pci0 = &pci0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8560@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <0x20>;	// 32 bytes
+			i-cache-line-size = <0x20>;	// 32 bytes
+			d-cache-size = <0x8000>;	// L1, 32K
+			i-cache-size = <0x8000>;	// L1, 32K
+			timebase-frequency = <0>;	// From uboot
+			bus-frequency = <0>;
+			clock-frequency = <0>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	soc@ff700000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		ranges = <0x0 0xff700000 0x00100000>;
+		reg = <0xff700000 0x00100000>;
+		clock-frequency = <0>;
+
+		memory-controller@2000 {
+			compatible = "fsl,8560-memory-controller";
+			reg = <0x2000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <0x12 0x2>;
+		};
+
+		l2-cache-controller@20000 {
+			compatible = "fsl,8560-l2-cache-controller";
+			reg = <0x20000 0x1000>;
+			cache-line-size = <0x20>;	// 32 bytes
+			cache-size = <0x40000>;		// L2, 256K
+			interrupt-parent = <&mpic>;
+			interrupts = <0x10 0x2>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <0x2b 0x2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <0x2b 0x2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		mdio@24520 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,gianfar-mdio";
+			reg = <0x24520 0x20>;
+			phy0: ethernet-phy@19 {
+				interrupt-parent = <&mpic>;
+				interrupts = <0x6 0x1>;
+				reg = <0x19>;
+				device_type = "ethernet-phy";
+			};
+			phy1: ethernet-phy@1a {
+				interrupt-parent = <&mpic>;
+				interrupts = <0x7 0x1>;
+				reg = <0x1a>;
+				device_type = "ethernet-phy";
+			};
+			phy2: ethernet-phy@1b {
+				interrupt-parent = <&mpic>;
+				interrupts = <0x8 0x1>;
+				reg = <0x1b>;
+				device_type = "ethernet-phy";
+			};
+			phy3: ethernet-phy@1c {
+				interrupt-parent = <&mpic>;
+				interrupts = <0x8 0x1>;
+				reg = <0x1c>;
+				device_type = "ethernet-phy";
+			};
+		};
+
+		enet0: ethernet@24000 {
+			cell-index = <0>;
+			device_type = "network";
+			model = "TSEC";
+			compatible = "gianfar";
+			reg = <0x24000 0x1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy0>;
+		};
+
+		enet1: ethernet@25000 {
+			cell-index = <1>;
+			device_type = "network";
+			model = "TSEC";
+			compatible = "gianfar";
+			reg = <0x25000 0x1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <0x23 0x2 0x24 0x2 0x28 0x2>;
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy1>;
+		};
+
+		mpic: pic@40000 {
+			interrupt-controller;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x40000 0x40000>;
+			device_type = "open-pic";
+		};
+
+		cpm@919c0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,mpc8560-cpm", "fsl,cpm2";
+			reg = <0x919c0 0x30>;
+			ranges;
+
+			muram@80000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x80000 0x10000>;
+
+				data@0 {
+					compatible = "fsl,cpm-muram-data";
+					reg = <0x0 0x4000 0x9000 0x2000>;
+				};
+			};
+
+			brg@919f0 {
+				compatible = "fsl,mpc8560-brg",
+				             "fsl,cpm2-brg",
+				             "fsl,cpm-brg";
+				reg = <0x919f0 0x10 0x915f0 0x10>;
+				clock-frequency = <165000000>;
+			};
+
+			cpmpic: pic@90c00 {
+				interrupt-controller;
+				#address-cells = <0>;
+				#interrupt-cells = <2>;
+				interrupts = <0x2e 0x2>;
+				interrupt-parent = <&mpic>;
+				reg = <0x90c00 0x80>;
+				compatible = "fsl,mpc8560-cpm-pic", "fsl,cpm2-pic";
+			};
+
+			enet2: ethernet@91320 {
+				device_type = "network";
+				compatible = "fsl,mpc8560-fcc-enet",
+				             "fsl,cpm2-fcc-enet";
+				reg = <0x91320 0x20 0x88500 0x100 0x913b0 0x1>;
+				local-mac-address = [ 00 00 00 00 00 00 ];
+				fsl,cpm-command = <0x16200300>;
+				interrupts = <0x21 0x8>;
+				interrupt-parent = <&cpmpic>;
+				phy-handle = <&phy2>;
+			};
+
+			enet3: ethernet@91340 {
+				device_type = "network";
+				compatible = "fsl,mpc8560-fcc-enet",
+				             "fsl,cpm2-fcc-enet";
+				reg = <0x91340 0x20 0x88600 0x100 0x913d0 0x1>;
+				local-mac-address = [ 00 00 00 00 00 00 ];
+				fsl,cpm-command = <0x1a400300>;
+				interrupts = <0x22 0x8>;
+				interrupt-parent = <&cpmpic>;
+				phy-handle = <&phy3>;
+			};
+		};
+
+		global-utilities@e0000 {
+			compatible = "fsl,mpc8560-guts";
+			reg = <0xe0000 0x1000>;
+			fsl,has-rstcr;
+		};
+	};
+
+	pci0: pci@ff708000 {
+		cell-index = <0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
+		device_type = "pci";
+		reg = <0xff708000 0x1000>;
+		clock-frequency = <66666666>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+
+			/* IDSEL 0x02 */
+			0x1000 0x0 0x0 0x1 &mpic 0x2 0x1
+			0x1000 0x0 0x0 0x2 &mpic 0x3 0x1
+			0x1000 0x0 0x0 0x3 &mpic 0x4 0x1
+			0x1000 0x0 0x0 0x4 &mpic 0x5 0x1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <0x18 0x2>;
+		bus-range = <0x0 0x0>;
+		ranges = <0x02000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+			  0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+	};
+
+	localbus@ff705000 {
+		compatible = "fsl,mpc8560-localbus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <0xff705000 0x100>;	// BRx, ORx, etc.
+
+		ranges = <
+			0x0 0x0 0xff800000 0x0800000	// 8MB boot flash
+			0x1 0x0 0xe4000000 0x4000000	// 64MB flash
+			0x3 0x0 0x20000000 0x4000000	// 64MB SDRAM
+			0x4 0x0 0x24000000 0x4000000	// 64MB SDRAM
+			0x5 0x0 0xfc000000 0x0c00000	// EPLD
+			0x6 0x0 0xe0000000 0x4000000	// 64MB flash
+			0x7 0x0 0x80000000 0x0200000	// ATM1,2
+		>;
+
+		epld@5,0 {
+			compatible = "wrs,epld-localbus";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			reg = <0x5 0x0 0xc00000>;
+			ranges = <
+				0x0 0x0 0x5 0x000000 0x1fff	// LED disp.
+				0x1 0x0 0x5 0x100000 0x1fff	// switches
+				0x2 0x0 0x5 0x200000 0x1fff	// ID reg.
+				0x3 0x0 0x5 0x300000 0x1fff	// status reg.
+				0x4 0x0 0x5 0x400000 0x1fff	// reset reg.
+				0x5 0x0 0x5 0x500000 0x1fff	// Wind port
+				0x7 0x0 0x5 0x700000 0x1fff	// UART #1
+				0x8 0x0 0x5 0x800000 0x1fff	// UART #2
+				0x9 0x0 0x5 0x900000 0x1fff	// RTC
+				0xb 0x0 0x5 0xb00000 0x1fff	// EEPROM
+			>;
+
+			bidr@2,0 {
+				compatible = "wrs,sbc8560-bidr";
+				reg = <0x2 0x0 0x10>;
+			};
+
+			bcsr@3,0 {
+				compatible = "wrs,sbc8560-bcsr";
+				reg = <0x3 0x0 0x10>;
+			};
+
+			brstcr@4,0 {
+				compatible = "wrs,sbc8560-brstcr";
+				reg = <0x4 0x0 0x10>;
+			};
+
+			serial0: serial@7,0 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <0x7 0x0 0x100>;
+				clock-frequency = <1843200>;
+				interrupts = <0x9 0x2>;
+				interrupt-parent = <&mpic>;
+			};
+
+			serial1: serial@8,0 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <0x8 0x0 0x100>;
+				clock-frequency = <1843200>;
+				interrupts = <0xa 0x2>;
+				interrupt-parent = <&mpic>;
+			};
+
+			rtc@9,0 {
+				compatible = "m48t59";
+				reg = <0x9 0x0 0x1fff>;
+			};
+		};
+	};
+};
-- 
1.5.0.rc1.gf4b6c

[PATCH 3/10] CPM2: Make support for the CPM2 optional on 8560 based boards

[Paul Gortmaker]

Currently there is no way to disable the CPM2 support.  Some boards,
like the SBC8560 have their own external UART and don't have any direct
dependencies on the CPM for a serial console or anything else.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/platforms/85xx/Kconfig |    4 ++--
 arch/powerpc/platforms/Kconfig      |    4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 0eb497b..33d3bea 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -13,6 +13,7 @@ config MPC8560_ADS
 	bool "Freescale MPC8560 ADS"
 	select DEFAULT_UIMAGE
 	select PPC_CPM_NEW_BINDING
+	select CPM2
 	help
 	  This option enables support for the MPC 8560 ADS board
 
@@ -41,7 +42,7 @@ config MPC85xx_DS
 config SBC8560
 	bool "Wind River SBC8560"
 	select DEFAULT_UIMAGE
-	select PPC_CPM_NEW_BINDING
+	select PPC_CPM_NEW_BINDING if CPM2
 	help
 	  This option enables support for the Wind River SBC8560 board
 
@@ -55,7 +56,6 @@ config MPC8540
 
 config MPC8560
 	bool
-	select CPM2
 	default y if MPC8560_ADS || SBC8560
 
 config MPC85xx
diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index 2cec343..27b74e9 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -278,8 +278,8 @@ config QUICC_ENGINE
 	  for a machine with a QE coprocessor.
 
 config CPM2
-	bool
-	default n
+	bool "Enable support for the CPM2 (Communications Processor Module)"
+	depends on MPC8560 || 8260
 	select CPM
 	select PPC_LIB_RHEAP
 	help
-- 
1.5.0.rc1.gf4b6c

[PATCH 4/10] sbc8560: Add default .config file for Wind River SBC8560

[Paul Gortmaker]

This is a suitable .config file for building the WRS SBC8560 kernel
to be used for NFS root via one of the TSEC interfaces and with
serial console via the 16550 compatible UART on the board.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/configs/sbc8560_defconfig |  764 ++++++++++++++++++++++++++++++++
 1 files changed, 764 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/configs/sbc8560_defconfig b/arch/powerpc/configs/sbc8560_defconfig
new file mode 100644
index 0000000..d89fce0
--- /dev/null
+++ b/arch/powerpc/configs/sbc8560_defconfig
@@ -0,0 +1,764 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc4
+# Wed Jan 23 14:59:20 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+CONFIG_PPC_85xx=y
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_85xx=y
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+CONFIG_DEFAULT_UIMAGE=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPC8540_ADS is not set
+# CONFIG_MPC8560_ADS is not set
+# CONFIG_MPC85xx_CDS is not set
+# CONFIG_MPC85xx_MDS is not set
+# CONFIG_MPC85xx_DS is not set
+CONFIG_SBC8560=y
+CONFIG_MPC8560=y
+CONFIG_MPC85xx=y
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+# CONFIG_MATH_EMULATION is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE=""
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=y
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+# CONFIG_MTD is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+CONFIG_BROADCOM_PHY=y
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_NETDEV_1000=y
+CONFIG_GIANFAR=y
+CONFIG_GFAR_NAPI=y
+CONFIG_NETDEV_10000=y
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+# CONFIG_SERIAL_8250_EXTENDED is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_OF_PLATFORM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
+CONFIG_USB_SUPPORT=y
+# CONFIG_USB_ARCH_HAS_HCD is not set
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+CONFIG_RTC_DRV_M48T59=y
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+# CONFIG_MSDOS_PARTITION is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+# CONFIG_INSTRUMENTATION is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+CONFIG_PPC_EARLY_DEBUG=y
+# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
+# CONFIG_PPC_EARLY_DEBUG_G5 is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS_PANEL is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS_CONSOLE is not set
+# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
+# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
+# CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set
+# CONFIG_PPC_EARLY_DEBUG_BEAT is not set
+# CONFIG_PPC_EARLY_DEBUG_44x is not set
+# CONFIG_PPC_EARLY_DEBUG_CPM is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
-- 
1.5.0.rc1.gf4b6c

[PATCH 5/10] sbc8548: Add basic support for Wind River SBC8548 as powerpc

[Paul Gortmaker]

This adds the basic support for the Wind River SBC8548 board, implemented
as powerpc.  It closely follows the implementation of the MPC8548CDS.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/platforms/85xx/Kconfig   |   10 ++-
 arch/powerpc/platforms/85xx/Makefile  |    1 +
 arch/powerpc/platforms/85xx/sbc8548.c |  169 +++++++++++++++++++++++++++++++++
 3 files changed, 178 insertions(+), 2 deletions(-)

diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 33d3bea..8407f43 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -39,6 +39,12 @@ config MPC85xx_DS
 	help
 	  This option enables support for the MPC85xx DS (MPC8544 DS) board
 
+config SBC8548
+	bool "Wind River SBC8548"
+	select DEFAULT_UIMAGE
+	help
+	  This option enables support for the Wind River SBC8548 board
+
 config SBC8560
 	bool "Wind River SBC8560"
 	select DEFAULT_UIMAGE
@@ -52,7 +58,7 @@ config MPC8540
 	bool
 	select PPC_UDBG_16550
 	select PPC_INDIRECT_PCI
-	default y if MPC8540_ADS || MPC85xx_CDS
+	default y if MPC8540_ADS || MPC85xx_CDS || SBC8548
 
 config MPC8560
 	bool
@@ -66,4 +72,4 @@ config MPC85xx
 	select FSL_PCI if PCI
 	select SERIAL_8250_SHARE_IRQ if SERIAL_8250
 	default y if MPC8540_ADS || MPC85xx_CDS || MPC8560_ADS \
-		|| MPC85xx_MDS || MPC85xx_DS || SBC8560
+		|| MPC85xx_MDS || MPC85xx_DS || SBC8560 || SBC8548
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index c3f4d01..3a47b7a 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -6,4 +6,5 @@ obj-$(CONFIG_MPC8560_ADS) += mpc85xx_ads.o
 obj-$(CONFIG_MPC85xx_CDS) += mpc85xx_cds.o
 obj-$(CONFIG_MPC85xx_DS)  += mpc85xx_ds.o
 obj-$(CONFIG_MPC85xx_MDS) += mpc85xx_mds.o
+obj-$(CONFIG_SBC8548) += sbc8548.o
 obj-$(CONFIG_SBC8560) += sbc8560.o
diff --git a/arch/powerpc/platforms/85xx/sbc8548.c b/arch/powerpc/platforms/85xx/sbc8548.c
new file mode 100644
index 0000000..de27b57
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/sbc8548.c
@@ -0,0 +1,169 @@
+/*
+ * Wind River SBC8548 setup and early boot code.
+ *
+ * Copyright 2007 Wind River Systems Inc.
+ *
+ * By Paul Gortmaker (see MAINTAINERS for contact information)
+ *
+ * Based largely on the MPC8548CDS support - Copyright 2005 Freescale Inc.
+ *
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/reboot.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/major.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/initrd.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/fsl_devices.h>
+#include <linux/of_platform.h>
+
+#include <asm/system.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/atomic.h>
+#include <asm/time.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/ipic.h>
+#include <asm/pci-bridge.h>
+#include <asm/irq.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+static void __init sbc8548_pic_init(void)
+{
+	struct mpic *mpic;
+	struct resource r;
+	struct device_node *np = NULL;
+
+	np = of_find_node_by_type(np, "open-pic");
+
+	if (np == NULL) {
+		printk(KERN_ERR "Could not find open-pic node\n");
+		return;
+	}
+
+	if (of_address_to_resource(np, 0, &r)) {
+		printk(KERN_ERR "Failed to map mpic register space\n");
+		of_node_put(np);
+		return;
+	}
+
+	mpic = mpic_alloc(np, r.start,
+			MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN,
+			0, 256, " OpenPIC  ");
+	BUG_ON(mpic == NULL);
+
+	/* Return the mpic node */
+	of_node_put(np);
+
+	mpic_init(mpic);
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init sbc8548_setup_arch(void)
+{
+#ifdef CONFIG_PCI
+	struct device_node *np;
+#endif
+
+	if (ppc_md.progress)
+		ppc_md.progress("sbc8548_setup_arch()", 0);
+
+#ifdef CONFIG_PCI
+	for_each_node_by_type(np, "pci") {
+		if (of_device_is_compatible(np, "fsl,mpc8540-pci") ||
+		    of_device_is_compatible(np, "fsl,mpc8548-pcie")) {
+			struct resource rsrc;
+			of_address_to_resource(np, 0, &rsrc);
+			if ((rsrc.start & 0xfffff) == 0x8000)
+				fsl_add_bridge(np, 1);
+			else
+				fsl_add_bridge(np, 0);
+		}
+	}
+#endif
+}
+
+static void sbc8548_show_cpuinfo(struct seq_file *m)
+{
+	uint pvid, svid, phid1;
+	uint memsize = total_memory;
+
+	pvid = mfspr(SPRN_PVR);
+	svid = mfspr(SPRN_SVR);
+
+	seq_printf(m, "Vendor\t\t: Wind River\n");
+	seq_printf(m, "Machine\t\t: SBC8548\n");
+	seq_printf(m, "PVR\t\t: 0x%x\n", pvid);
+	seq_printf(m, "SVR\t\t: 0x%x\n", svid);
+
+	/* Display cpu Pll setting */
+	phid1 = mfspr(SPRN_HID1);
+	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
+
+	/* Display the amount of memory */
+	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
+}
+
+static struct of_device_id __initdata of_bus_ids[] = {
+	{ .name = "soc", },
+	{ .type = "soc", },
+	{},
+};
+
+static int __init declare_of_platform_devices(void)
+{
+	if (!machine_is(sbc8548))
+		return 0;
+
+	of_platform_bus_probe(NULL, of_bus_ids, NULL);
+	return 0;
+}
+device_initcall(declare_of_platform_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init sbc8548_probe(void)
+{
+        unsigned long root = of_get_flat_dt_root();
+
+        return of_flat_dt_is_compatible(root, "SBC8548");
+}
+
+define_machine(sbc8548) {
+	.name		= "SBC8548",
+	.probe		= sbc8548_probe,
+	.setup_arch	= sbc8548_setup_arch,
+	.init_IRQ	= sbc8548_pic_init,
+	.show_cpuinfo	= sbc8548_show_cpuinfo,
+	.get_irq	= mpic_get_irq,
+	.restart	= fsl_rstcr_restart,
+#ifdef CONFIG_PCI
+	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+#endif
+	.calibrate_decr = generic_calibrate_decr,
+	.progress	= udbg_progress,
+};
-- 
1.5.0.rc1.gf4b6c

[PATCH 6/10] sbc8548: Add v1 device tree source for Wind River SBC8548 board

[Paul Gortmaker]

This adds a v1 device tree source for the Wind River SBC8548 board.
The biggest difference between this and the MPC8548CDS reference
platform is the absence of the CDS's Arcadia peripherals and physical
access to the PCI#2 bus.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/boot/dts/sbc8548.dts |  244 +++++++++++++++++++++++++++++++++++++
 1 files changed, 244 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/boot/dts/sbc8548.dts b/arch/powerpc/boot/dts/sbc8548.dts
new file mode 100644
index 0000000..14be38a
--- /dev/null
+++ b/arch/powerpc/boot/dts/sbc8548.dts
@@ -0,0 +1,244 @@
+/*
+ * SBC8548 Device Tree Source
+ *
+ * Copyright 2007 Wind River Systems Inc.
+ *
+ * Paul Gortmaker (see MAINTAINERS for contact information)
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+
+/dts-v1/;
+
+/ {
+	model = "SBC8548";
+	compatible = "SBC8548";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		pci0 = &pci0;
+		/* pci1 doesn't have a corresponding physical connector */
+		pci2 = &pci2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8548@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <0x20>;	// 32 bytes
+			i-cache-line-size = <0x20>;	// 32 bytes
+			d-cache-size = <0x8000>;	// L1, 32K
+			i-cache-size = <0x8000>;	// L1, 32K
+			timebase-frequency = <0>;	// From uboot
+			bus-frequency = <0>;
+			clock-frequency = <0>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	soc8548@e0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		ranges = <0x00000000 0xe0000000 0x00100000>;
+		reg = <0xe0000000 0x00001000>;	// CCSRBAR
+		bus-frequency = <0>;
+
+		memory-controller@2000 {
+			compatible = "fsl,8548-memory-controller";
+			reg = <0x2000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <0x12 0x2>;
+		};
+
+		l2-cache-controller@20000 {
+			compatible = "fsl,8548-l2-cache-controller";
+			reg = <0x20000 0x1000>;
+			cache-line-size = <0x20>;	// 32 bytes
+			cache-size = <0x80000>;	// L2, 512K
+			interrupt-parent = <&mpic>;
+			interrupts = <0x10 0x2>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <0x2b 0x2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <0x2b 0x2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		mdio@24520 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,gianfar-mdio";
+			reg = <0x24520 0x20>;
+
+			phy0: ethernet-phy@19 {
+				interrupt-parent = <&mpic>;
+				interrupts = <0x6 0x1>;
+				reg = <0x19>;
+				device_type = "ethernet-phy";
+			};
+			phy1: ethernet-phy@1a {
+				interrupt-parent = <&mpic>;
+				interrupts = <0x7 0x1>;
+				reg = <0x1a>;
+				device_type = "ethernet-phy";
+			};
+		};
+
+		enet0: ethernet@24000 {
+			cell-index = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "gianfar";
+			reg = <0x24000 0x1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy0>;
+		};
+
+		enet1: ethernet@25000 {
+			cell-index = <1>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "gianfar";
+			reg = <0x25000 0x1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <0x23 0x2 0x24 0x2 0x28 0x2>;
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy1>;
+		};
+
+		serial0: serial@4500 {
+			cell-index = <0>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4500 0x100>;	// reg base, size
+			clock-frequency = <0>;	// should we fill in in uboot?
+			interrupts = <0x2a 0x2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		serial1: serial@4600 {
+			cell-index = <1>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4600 0x100>;	// reg base, size
+			clock-frequency = <0>;	// should we fill in in uboot?
+			interrupts = <0x2a 0x2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		global-utilities@e0000 {	//global utilities reg
+			compatible = "fsl,mpc8548-guts";
+			reg = <0xe0000 0x1000>;
+			fsl,has-rstcr;
+		};
+
+		mpic: pic@40000 {
+			interrupt-controller;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x40000 0x40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+                        big-endian;
+		};
+	};
+
+	pci0: pci@e0008000 {
+		cell-index = <0>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+			/* IDSEL 0x01 (PCI-X slot) */
+			0x0800 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x0800 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x0800 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x0800 0x0 0x0 0x4 &mpic 0x3 0x1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <0x18 0x2>;
+		bus-range = <0 0>;
+		ranges = <0x02000000 0x0 0x80000000 0x80000000 0x0 0x10000000
+			  0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00800000>;
+		clock-frequency = <66666666>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0xe0008000 0x1000>;
+		compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
+		device_type = "pci";
+	};
+
+	pci2: pcie@e000a000 {
+		cell-index = <2>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+
+			/* IDSEL 0x0 (PEX) */
+			0x0000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x0000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x0000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x0000 0x0 0x0 0x4 &mpic 0x3 0x1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <0x1a 0x2>;
+		bus-range = <0x0 0xff>;
+		ranges = <0x02000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+			  0x01000000 0x0 0x00000000 0xe3000000 0x0 0x08000000>;
+		clock-frequency = <33333333>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0xe000a000 0x1000>;
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		pcie@0 {
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <0x02000000 0x0 0xa0000000
+				  0x02000000 0x0 0xa0000000
+				  0x0 0x20000000
+
+				  0x01000000 0x0 0x00000000
+				  0x01000000 0x0 0x00000000
+				  0x0 0x08000000>;
+		};
+	};
+};
-- 
1.5.0.rc1.gf4b6c

[PATCH 7/10] sbc8548: Add default .config file for Wind River SBC8548

[Paul Gortmaker]

This is a suitable .config file for building the WRS SBC8548 kernel
to be used for NFS root via one of the TSEC interfaces and with
serial console via the soc/16550 compatible UART.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/configs/sbc8548_defconfig |  741 ++++++++++++++++++++++++++++++++
 1 files changed, 741 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/configs/sbc8548_defconfig b/arch/powerpc/configs/sbc8548_defconfig
new file mode 100644
index 0000000..3b7fa53
--- /dev/null
+++ b/arch/powerpc/configs/sbc8548_defconfig
@@ -0,0 +1,741 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc8
+# Thu Jan 24 15:19:12 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+CONFIG_PPC_85xx=y
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_85xx=y
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+CONFIG_DEFAULT_UIMAGE=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPC8540_ADS is not set
+# CONFIG_MPC8560_ADS is not set
+# CONFIG_MPC85xx_CDS is not set
+# CONFIG_MPC85xx_MDS is not set
+# CONFIG_MPC85xx_DS is not set
+CONFIG_SBC8548=y
+# CONFIG_SBC8560 is not set
+CONFIG_MPC8540=y
+CONFIG_MPC85xx=y
+# CONFIG_IPIC is not set
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_MATH_EMULATION=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE=""
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_FSL_SOC=y
+CONFIG_FSL_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
+# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=y
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+# CONFIG_MTD is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_ARCNET is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+CONFIG_BROADCOM_PHY=y
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
+# CONFIG_IP1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_GIANFAR=y
+CONFIG_GFAR_NAPI=y
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+# CONFIG_NIU is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_PCI=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+# CONFIG_SERIAL_OF_PLATFORM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_I5K_AMB is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_VT8231 is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_INFINIBAND is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+# CONFIG_INSTRUMENTATION is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
-- 
1.5.0.rc1.gf4b6c

[PATCH 8/10] sbc834x: Add support for Wind River SBC834x boards

[Paul Gortmaker]

This adds the basic support for the Wind River SBC834x boards.  The
SBC8349 is more common, although it should work on the SBC8347 board
as well.  Support is heavily based on the existing MPC834x_MDS code.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/platforms/83xx/Kconfig   |    9 ++-
 arch/powerpc/platforms/83xx/Makefile  |    1 +
 arch/powerpc/platforms/83xx/sbc834x.c |  115 +++++++++++++++++++++++++++++++++
 3 files changed, 124 insertions(+), 1 deletions(-)

diff --git a/arch/powerpc/platforms/83xx/Kconfig b/arch/powerpc/platforms/83xx/Kconfig
index 2430ac8..782bff0 100644
--- a/arch/powerpc/platforms/83xx/Kconfig
+++ b/arch/powerpc/platforms/83xx/Kconfig
@@ -55,6 +55,13 @@ config MPC837x_MDS
 	select DEFAULT_UIMAGE
 	help
 	  This option enables support for the MPC837x MDS Processor Board.
+
+config SBC834x
+	bool "Wind River SBC834x"
+	select DEFAULT_UIMAGE
+	help
+	  This option enables support for the Wind River SBC834x board.
+
 endchoice
 
 config PPC_MPC831x
@@ -73,7 +80,7 @@ config MPC834x
 	bool
 	select PPC_UDBG_16550
 	select PPC_INDIRECT_PCI
-	default y if MPC834x_MDS || MPC834x_ITX
+	default y if MPC834x_MDS || MPC834x_ITX || SBC834x
 
 config PPC_MPC836x
 	bool
diff --git a/arch/powerpc/platforms/83xx/Makefile b/arch/powerpc/platforms/83xx/Makefile
index df46629..3a35242 100644
--- a/arch/powerpc/platforms/83xx/Makefile
+++ b/arch/powerpc/platforms/83xx/Makefile
@@ -10,3 +10,4 @@ obj-$(CONFIG_MPC834x_ITX)	+= mpc834x_itx.o
 obj-$(CONFIG_MPC836x_MDS)	+= mpc836x_mds.o
 obj-$(CONFIG_MPC832x_MDS)	+= mpc832x_mds.o
 obj-$(CONFIG_MPC837x_MDS)	+= mpc837x_mds.o
+obj-$(CONFIG_SBC834x)		+= sbc834x.o
diff --git a/arch/powerpc/platforms/83xx/sbc834x.c b/arch/powerpc/platforms/83xx/sbc834x.c
new file mode 100644
index 0000000..cf38247
--- /dev/null
+++ b/arch/powerpc/platforms/83xx/sbc834x.c
@@ -0,0 +1,115 @@
+/*
+ * arch/powerpc/platforms/83xx/sbc834x.c
+ *
+ * Wind River SBC834x board specific routines
+ *
+ * By Paul Gortmaker (see MAINTAINERS for contact information)
+ *
+ * Based largely on the mpc834x_mds.c support by Kumar Gala.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/reboot.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/major.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/of_platform.h>
+
+#include <asm/system.h>
+#include <asm/atomic.h>
+#include <asm/time.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/ipic.h>
+#include <asm/irq.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <sysdev/fsl_soc.h>
+
+#include "mpc83xx.h"
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+static void __init sbc834x_setup_arch(void)
+{
+#ifdef CONFIG_PCI
+	struct device_node *np;
+#endif
+
+	if (ppc_md.progress)
+		ppc_md.progress("sbc834x_setup_arch()", 0);
+
+#ifdef CONFIG_PCI
+	for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
+		mpc83xx_add_bridge(np);
+#endif
+
+}
+
+static void __init sbc834x_init_IRQ(void)
+{
+	struct device_node *np;
+
+	np = of_find_node_by_type(NULL, "ipic");
+	if (!np)
+		return;
+
+	ipic_init(np, 0);
+
+	/* Initialize the default interrupt mapping priorities,
+	 * in case the boot rom changed something on us.
+	 */
+	ipic_set_default_priority();
+
+	of_node_put(np);
+}
+
+static struct __initdata of_device_id sbc834x_ids[] = {
+	{ .type = "soc", },
+	{ .compatible = "soc", },
+	{},
+};
+
+static int __init sbc834x_declare_of_platform_devices(void)
+{
+	of_platform_bus_probe(NULL, sbc834x_ids, NULL);
+	return 0;
+}
+machine_device_initcall(sbc834x, sbc834x_declare_of_platform_devices);
+
+/*
+ * Called very early, MMU is off, device-tree isn't unflattened
+ */
+static int __init sbc834x_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+
+	return of_flat_dt_is_compatible(root, "SBC834x");
+}
+
+define_machine(sbc834x) {
+	.name			= "SBC834x",
+	.probe			= sbc834x_probe,
+	.setup_arch		= sbc834x_setup_arch,
+	.init_IRQ		= sbc834x_init_IRQ,
+	.get_irq		= ipic_get_irq,
+	.restart		= mpc83xx_restart,
+	.time_init		= mpc83xx_time_init,
+	.calibrate_decr		= generic_calibrate_decr,
+	.progress		= udbg_progress,
+};
-- 
1.5.0.rc1.gf4b6c

[PATCH 9/10] sbc834x: Add device tree source for Wind River SBC834x board.

[Paul Gortmaker]

This adds the device tree source for the Wind River SBC834x board.
It is based on the MPC834x_MDS DTS, with the biggest difference being
the lack of BCSR and the PCI2 that the MDS gets via the PIB. That,
and this file is also dts-v1 format.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/boot/dts/sbc8349.dts |  243 +++++++++++++++++++++++++++++++++++++
 1 files changed, 243 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts
new file mode 100644
index 0000000..9c13c1a
--- /dev/null
+++ b/arch/powerpc/boot/dts/sbc8349.dts
@@ -0,0 +1,243 @@
+/*
+ * SBC8349E Device Tree Source
+ *
+ * Copyright 2007 Wind River Inc.
+ *
+ * Paul Gortmaker (see MAINTAINERS for contact information)
+ *
+ *	-based largely on the Freescale MPC834x_MDS dts.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+	model = "SBC8349E";
+	compatible = "SBC834xE";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		pci0 = &pci0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8349@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <0x20>;	// 32 bytes
+			i-cache-line-size = <0x20>;	// 32 bytes
+			d-cache-size = <0x8000>;		// L1, 32K
+			i-cache-size = <0x8000>;		// L1, 32K
+			timebase-frequency = <0>;	// from bootloader
+			bus-frequency = <0>;		// from bootloader
+			clock-frequency = <0>;		// from bootloader
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;	// 256MB at 0
+	};
+
+	soc8349@e0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		ranges = <0x0 0xe0000000 0x00100000>;
+		reg = <0xe0000000 0x00000200>;
+		bus-frequency = <0>;
+
+		wdt@200 {
+			compatible = "mpc83xx_wdt";
+			reg = <0x200 0x100>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <0xe 0x8>;
+			interrupt-parent = <&ipic>;
+			dfsrr;
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <0xf 0x8>;
+			interrupt-parent = <&ipic>;
+			dfsrr;
+		};
+
+		spi@7000 {
+			compatible = "fsl_spi";
+			reg = <0x7000 0x1000>;
+			interrupts = <0x10 0x8>;
+			interrupt-parent = <&ipic>;
+			mode = "cpu";
+		};
+
+		/* phy type (ULPI or SERIAL) are only types supported for MPH */
+		/* port = 0 or 1 */
+		usb@22000 {
+			compatible = "fsl-usb2-mph";
+			reg = <0x22000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupt-parent = <&ipic>;
+			interrupts = <0x27 0x8>;
+			phy_type = "ulpi";
+			port1;
+		};
+		/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
+		usb@23000 {
+			device_type = "usb";
+			compatible = "fsl-usb2-dr";
+			reg = <0x23000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupt-parent = <&ipic>;
+			interrupts = <0x26 0x8>;
+			dr_mode = "otg";
+			phy_type = "ulpi";
+		};
+
+		mdio@24520 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,gianfar-mdio";
+			reg = <0x24520 0x20>;
+
+			phy0: ethernet-phy@19 {
+				interrupt-parent = <&ipic>;
+				interrupts = <0x14 0x8>;
+				reg = <0x19>;
+				device_type = "ethernet-phy";
+			};
+			phy1: ethernet-phy@1a {
+				interrupt-parent = <&ipic>;
+				interrupts = <0x15 0x8>;
+				reg = <0x1a>;
+				device_type = "ethernet-phy";
+			};
+		};
+
+		enet0: ethernet@24000 {
+			cell-index = <0>;
+			device_type = "network";
+			model = "TSEC";
+			compatible = "gianfar";
+			reg = <0x24000 0x1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <0x20 0x8 0x21 0x8 0x22 0x8>;
+			interrupt-parent = <&ipic>;
+			phy-handle = <&phy0>;
+			linux,network-index = <0>;
+		};
+
+		enet1: ethernet@25000 {
+			cell-index = <1>;
+			device_type = "network";
+			model = "TSEC";
+			compatible = "gianfar";
+			reg = <0x25000 0x1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <0x23 0x8 0x24 0x8 0x25 0x8>;
+			interrupt-parent = <&ipic>;
+			phy-handle = <&phy1>;
+			linux,network-index = <1>;
+		};
+
+		serial0: serial@4500 {
+			cell-index = <0>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4500 0x100>;
+			clock-frequency = <0>;
+			interrupts = <0x9 0x8>;
+			interrupt-parent = <&ipic>;
+		};
+
+		serial1: serial@4600 {
+			cell-index = <1>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4600 0x100>;
+			clock-frequency = <0>;
+			interrupts = <0xa 0x8>;
+			interrupt-parent = <&ipic>;
+		};
+
+		/* May need to remove if on a part without crypto engine */
+		crypto@30000 {
+			model = "SEC2";
+			compatible = "talitos";
+			reg = <0x30000 0x10000>;
+			interrupts = <0xb 0x8>;
+			interrupt-parent = <&ipic>;
+			num-channels = <4>;
+			channel-fifo-len = <0x18>;
+			exec-units-mask = <0x0000007e>;
+			/* desc mask is for rev2.0,
+			 * we need runtime fixup for >2.0 */
+			descriptor-types-mask = <0x01010ebf>;
+		};
+
+		/* IPIC
+		 * interrupts cell = <intr #, sense>
+		 * sense values match linux IORESOURCE_IRQ_* defines:
+		 * sense == 8: Level, low assertion
+		 * sense == 2: Edge, high-to-low change
+		 */
+		ipic: pic@700 {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x700 0x100>;
+			device_type = "ipic";
+		};
+	};
+
+	pci0: pci@e0008500 {
+		cell-index = <1>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+
+				/* IDSEL 0x11 */
+				 0x8800 0x0 0x0 0x1 &ipic 0x14 0x8
+				 0x8800 0x0 0x0 0x2 &ipic 0x15 0x8
+				 0x8800 0x0 0x0 0x3 &ipic 0x16 0x8
+				 0x8800 0x0 0x0 0x4 &ipic 0x17 0x8>;
+
+		interrupt-parent = <&ipic>;
+		interrupts = <0x42 0x8>;
+		bus-range = <0 0>;
+		ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
+			  0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
+			  0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+		clock-frequency = <66666666>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0xe0008500 0x100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
+};
-- 
1.5.0.rc1.gf4b6c

[PATCH 10/10] sbc834x: Add default config file for Wind River SBC8349 board

[Paul Gortmaker]

Default config file for SBC8349 board, suitable for use as with NFS as
a root file system and gianfar as the NFS root device.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
 arch/powerpc/configs/sbc834x_defconfig |  800 ++++++++++++++++++++++++++++++++
 1 files changed, 800 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/configs/sbc834x_defconfig b/arch/powerpc/configs/sbc834x_defconfig
new file mode 100644
index 0000000..9245bcc
--- /dev/null
+++ b/arch/powerpc/configs/sbc834x_defconfig
@@ -0,0 +1,800 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc8
+# Thu Jan 24 15:54:27 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+CONFIG_6xx=y
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_83xx=y
+CONFIG_PPC_FPU=y
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
+# CONFIG_SMP is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+CONFIG_DEFAULT_UIMAGE=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+# CONFIG_KALLSYMS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+# CONFIG_EPOLL is not set
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+# CONFIG_KMOD is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MULTIPLATFORM is not set
+# CONFIG_PPC_82xx is not set
+CONFIG_PPC_83xx=y
+# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPC8313_RDB is not set
+# CONFIG_MPC832x_MDS is not set
+# CONFIG_MPC832x_RDB is not set
+# CONFIG_MPC834x_MDS is not set
+# CONFIG_MPC834x_ITX is not set
+# CONFIG_MPC836x_MDS is not set
+# CONFIG_MPC837x_MDS is not set
+CONFIG_SBC834x=y
+CONFIG_MPC834x=y
+CONFIG_IPIC=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+CONFIG_SECCOMP=y
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE=""
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_ISA_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=m
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+# CONFIG_MTD is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+CONFIG_BROADCOM_PHY=y
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_NETDEV_1000=y
+CONFIG_GIANFAR=y
+# CONFIG_GFAR_NAPI is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_OF_PLATFORM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+CONFIG_83xx_WDT=y
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+# CONFIG_INSTRUMENTATION is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=m
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_XTS is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_TEST is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_PPC_CLOCK is not set
-- 
1.5.0.rc1.gf4b6c

Re: [PATCH 3/10] CPM2: Make support for the CPM2 optional on 8560 based boards

[Scott Wood]

Paul Gortmaker wrote:
> @@ -41,7 +42,7 @@ config MPC85xx_DS
>  config SBC8560
>  	bool "Wind River SBC8560"
>  	select DEFAULT_UIMAGE
> -	select PPC_CPM_NEW_BINDING
> +	select PPC_CPM_NEW_BINDING if CPM2
>  	help
>  	  This option enables support for the Wind River SBC8560 board

Setting PPC_CPM_NEW_BINGING should be harmless if CPM2 isn't set.  Looks 
good otherwise.

-Scott

Re: [PATCH 3/10] CPM2: Make support for the CPM2 optional on 8560 based boards

[Paul Gortmaker]

Scott Wood wrote:
> Paul Gortmaker wrote:
>> @@ -41,7 +42,7 @@ config MPC85xx_DS
>>  config SBC8560
>>      bool "Wind River SBC8560"
>>      select DEFAULT_UIMAGE
>> -    select PPC_CPM_NEW_BINDING
>> +    select PPC_CPM_NEW_BINDING if CPM2
>>      help
>>        This option enables support for the Wind River SBC8560 board
>
> Setting PPC_CPM_NEW_BINGING should be harmless if CPM2 isn't set.  
> Looks good otherwise.
>
> -Scott
>

Yes, it should be harmless;  I was just thinking of it
from the point of view of less chatter in the .config
file (yes, you could say that is a lost cause...)

P.

Re: [PATCH 0/10] Support for SBC834x/8548/8560 Wind River Boards

[Kumar Gala]

On Thu, 24 Jan 2008, Paul Gortmaker wrote:

>
> This series contains the patches for the Wind River SBC834x, SBC8548 and
> SBC8560, grouped together for merge convenience.
>
> Changes since previous:
>
> sbc834x:
> 	- machine_device_initcall as per Kumar's recent commit 6392f184
> 	- remove four device_type from dts that DavidG wanted gone.
> 	- add of_node_put() and __initdata as per StephenR's suggestions.
>
> sbc8548:
> 	- fold the dts, and conversion to dts-v1, into a single commit
>
> sbc8560:
> 	- dts has localbus with 2 address cells (chipsel) and epld as child
> 	- UART detection legacy_serial patch separated out from 8560 patches
> 	- fold the dts, and conversion to dts-v1, into a single commit
>
> I've boot tested these all on "for-2.6.25" to make sure things are sane.
> Thanks again to those who have suggested improvements and changes.

applied.

- k

Re: [PATCH 2/10] sbc8560: Add v1 device tree source for Wind River SBC8560 board

[David Gibson]

On Thu, Jan 24, 2008 at 06:41:24PM -0500, Paul Gortmaker wrote:
> This adds a v1 device tree source for the Wind River SBC8560 board.  The
> biggest difference between this and the MPC8560ADS reference platform
> dts is the use of an external 16550 compatible UART instead of the CPM2.
> 
> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

[snip]
> +/dts-v1/;
> +
> +/ {
> +	model = "SBC8560";
> +	compatible = "SBC8560";

This is not the conventional format for board-level compatible
entries, which should generally be "vendor,model" and all in lower
case.

[snip]
> +		enet0: ethernet@24000 {
> +			cell-index = <0>;
> +			device_type = "network";
> +			model = "TSEC";
> +			compatible = "gianfar";

This looks like the old dodgy gianfar binding, and needs updating
(mdio node will probably also need changes).

[snip]
> +	localbus@ff705000 {
> +		compatible = "fsl,mpc8560-localbus";
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		reg = <0xff705000 0x100>;	// BRx, ORx, etc.
> +
> +		ranges = <
> +			0x0 0x0 0xff800000 0x0800000	// 8MB boot flash
> +			0x1 0x0 0xe4000000 0x4000000	// 64MB flash
> +			0x3 0x0 0x20000000 0x4000000	// 64MB SDRAM
> +			0x4 0x0 0x24000000 0x4000000	// 64MB SDRAM
> +			0x5 0x0 0xfc000000 0x0c00000	// EPLD
> +			0x6 0x0 0xe0000000 0x4000000	// 64MB flash
> +			0x7 0x0 0x80000000 0x0200000	// ATM1,2
> +		>;
> +
> +		epld@5,0 {

I'm not entirely convinced on this two-level representation.  I think
the FSL people need to get together and define a binding (or set of
bindings) for their various chipselect style external bus bridges.

> +			compatible = "wrs,epld-localbus";
> +			#address-cells = <2>;
> +			#size-cells = <1>;
> +			reg = <0x5 0x0 0xc00000>;
> +			ranges = <
> +				0x0 0x0 0x5 0x000000 0x1fff	// LED disp.
> +				0x1 0x0 0x5 0x100000 0x1fff	// switches
> +				0x2 0x0 0x5 0x200000 0x1fff	// ID reg.
> +				0x3 0x0 0x5 0x300000 0x1fff	// status reg.
> +				0x4 0x0 0x5 0x400000 0x1fff	// reset reg.
> +				0x5 0x0 0x5 0x500000 0x1fff	// Wind port
> +				0x7 0x0 0x5 0x700000 0x1fff	// UART #1
> +				0x8 0x0 0x5 0x800000 0x1fff	// UART #2
> +				0x9 0x0 0x5 0x900000 0x1fff	// RTC
> +				0xb 0x0 0x5 0xb00000 0x1fff	// EEPROM
> +			>;

-- 
David Gibson			| I'll have my music baroque, and my code
david AT gibson.dropbear.id.au	| minimalist, thank you.  NOT _the_ _other_
				| _way_ _around_!
http://www.ozlabs.org/~dgibson

Re: [PATCH 2/10] sbc8560: Add v1 device tree source for Wind River SBC8560 board

[Kumar Gala]

On Feb 1, 2008, at 1:54 AM, David Gibson wrote:

> On Thu, Jan 24, 2008 at 06:41:24PM -0500, Paul Gortmaker wrote:
>> This adds a v1 device tree source for the Wind River SBC8560  
>> board.  The
>> biggest difference between this and the MPC8560ADS reference platform
>> dts is the use of an external 16550 compatible UART instead of the  
>> CPM2.
>>
>> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
>
> [snip]
>> +/dts-v1/;
>> +
>> +/ {
>> +	model = "SBC8560";
>> +	compatible = "SBC8560";
>
> This is not the conventional format for board-level compatible
> entries, which should generally be "vendor,model" and all in lower
> case.
>
> [snip]
>> +		enet0: ethernet@24000 {
>> +			cell-index = <0>;
>> +			device_type = "network";
>> +			model = "TSEC";
>> +			compatible = "gianfar";
>
> This looks like the old dodgy gianfar binding, and needs updating
> (mdio node will probably also need changes).
>
> [snip]
>> +	localbus@ff705000 {
>> +		compatible = "fsl,mpc8560-localbus";
>> +		#address-cells = <2>;
>> +		#size-cells = <1>;
>> +		reg = <0xff705000 0x100>;	// BRx, ORx, etc.
>> +
>> +		ranges = <
>> +			0x0 0x0 0xff800000 0x0800000	// 8MB boot flash
>> +			0x1 0x0 0xe4000000 0x4000000	// 64MB flash
>> +			0x3 0x0 0x20000000 0x4000000	// 64MB SDRAM
>> +			0x4 0x0 0x24000000 0x4000000	// 64MB SDRAM
>> +			0x5 0x0 0xfc000000 0x0c00000	// EPLD
>> +			0x6 0x0 0xe0000000 0x4000000	// 64MB flash
>> +			0x7 0x0 0x80000000 0x0200000	// ATM1,2
>> +		>;
>> +
>> +		epld@5,0 {
>
> I'm not entirely convinced on this two-level representation.  I think
> the FSL people need to get together and define a binding (or set of
> bindings) for their various chipselect style external bus bridges.

It seems reasonable if you had a FPGA off of the localbus to have a  
two level representation.  One for the localbus controller on the FSL  
part and the child to describe the FPGA.

What are you expecting beyond what we have today?  I guess I'm asking  
what's missing from the localbus nodes we have?

- k

Re: [PATCH 2/10] sbc8560: Add v1 device tree source for Wind River SBC8560 board

[David Gibson]

On Fri, Feb 01, 2008 at 08:46:32AM -0600, Kumar Gala wrote:
> 
> On Feb 1, 2008, at 1:54 AM, David Gibson wrote:
> 
> > On Thu, Jan 24, 2008 at 06:41:24PM -0500, Paul Gortmaker wrote:
[snip]
> >> +		epld@5,0 {
> >
> > I'm not entirely convinced on this two-level representation.  I think
> > the FSL people need to get together and define a binding (or set of
> > bindings) for their various chipselect style external bus bridges.
> 
> It seems reasonable if you had a FPGA off of the localbus to have a  
> two level representation.  One for the localbus controller on the FSL  
> part and the child to describe the FPGA.
> 
> What are you expecting beyond what we have today?  I guess I'm asking  
> what's missing from the localbus nodes we have?

Sorry, I was probably misleading.  All I really meant is that I don't
know enough about these FSL bus bridge arrangements to assess if this
representation is the most sensible one.  I'm presuming that this
chipselect bridge unit is a more-or-less standard ASIC appearing on
lots of the FSL chips, so it would be nice to have a standard binding
for them, as we do for the roughly-equivalent EBC bridge on 4xx.

-- 
David Gibson			| I'll have my music baroque, and my code
david AT gibson.dropbear.id.au	| minimalist, thank you.  NOT _the_ _other_
				| _way_ _around_!
http://www.ozlabs.org/~dgibson

Re: [PATCH 2/10] sbc8560: Add v1 device tree source for Wind River SBC8560 board

[Kumar Gala]

On Feb 4, 2008, at 8:40 PM, David Gibson wrote:

> On Fri, Feb 01, 2008 at 08:46:32AM -0600, Kumar Gala wrote:
>>
>> On Feb 1, 2008, at 1:54 AM, David Gibson wrote:
>>
>>> On Thu, Jan 24, 2008 at 06:41:24PM -0500, Paul Gortmaker wrote:
> [snip]
>>>> +		epld@5,0 {
>>>
>>> I'm not entirely convinced on this two-level representation.  I  
>>> think
>>> the FSL people need to get together and define a binding (or set of
>>> bindings) for their various chipselect style external bus bridges.
>>
>> It seems reasonable if you had a FPGA off of the localbus to have a
>> two level representation.  One for the localbus controller on the FSL
>> part and the child to describe the FPGA.
>>
>> What are you expecting beyond what we have today?  I guess I'm asking
>> what's missing from the localbus nodes we have?
>
> Sorry, I was probably misleading.  All I really meant is that I don't
> know enough about these FSL bus bridge arrangements to assess if this
> representation is the most sensible one.  I'm presuming that this
> chipselect bridge unit is a more-or-less standard ASIC appearing on
> lots of the FSL chips, so it would be nice to have a standard binding
> for them, as we do for the roughly-equivalent EBC bridge on 4xx.

Is there a writeup for EBC?  I'll take a look at it and see if it  
makes senses for the freescale 'localbus'.

- k

Re: [PATCH 2/10] sbc8560: Add v1 device tree source for Wind River SBC8560 board

[Paul Gortmaker]

In message: Re: [PATCH 2/10] sbc8560: Add v1 device tree source for Wind River SBC8560 board
on 01/02/2008 David Gibson wrote:

> On Thu, Jan 24, 2008 at 06:41:24PM -0500, Paul Gortmaker wrote:
> > This adds a v1 device tree source for the Wind River SBC8560 board.  The
> > biggest difference between this and the MPC8560ADS reference platform
> > dts is the use of an external 16550 compatible UART instead of the CPM2.
> > 
> > Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
> 
> [snip]
> > +/dts-v1/;
> > +
> > +/ {
> > +	model = "SBC8560";
> > +	compatible = "SBC8560";
> 
> This is not the conventional format for board-level compatible
> entries, which should generally be "vendor,model" and all in lower
> case.

No problem - I can change to "sbc8560" and "wrs,sbc8560" on this board
and others.

> 
> [snip]
> > +		enet0: ethernet@24000 {
> > +			cell-index = <0>;
> > +			device_type = "network";
> > +			model = "TSEC";
> > +			compatible = "gianfar";
> 
> This looks like the old dodgy gianfar binding, and needs updating
> (mdio node will probably also need changes).

I thought I'd merged in all Kumar's updates to the gianfar nodes at that
point in time, but I'll go back and re-check.

> 
> [snip]
> > +	localbus@ff705000 {
> > +		compatible = "fsl,mpc8560-localbus";
> > +		#address-cells = <2>;
> > +		#size-cells = <1>;
> > +		reg = <0xff705000 0x100>;	// BRx, ORx, etc.
> > +
> > +		ranges = <
> > +			0x0 0x0 0xff800000 0x0800000	// 8MB boot flash
> > +			0x1 0x0 0xe4000000 0x4000000	// 64MB flash
> > +			0x3 0x0 0x20000000 0x4000000	// 64MB SDRAM
> > +			0x4 0x0 0x24000000 0x4000000	// 64MB SDRAM
> > +			0x5 0x0 0xfc000000 0x0c00000	// EPLD
> > +			0x6 0x0 0xe0000000 0x4000000	// 64MB flash
> > +			0x7 0x0 0x80000000 0x0200000	// ATM1,2
> > +		>;
> > +
> > +		epld@5,0 {
> 
> I'm not entirely convinced on this two-level representation.  I think
> the FSL people need to get together and define a binding (or set of
> bindings) for their various chipselect style external bus bridges.

I'd tried to capture what you'd outlined for the localbus node, and the
epld child seemed like a natural extension of that.  I suspect that a
lot of boards would just have the localbus node and not the extra node
that fans things out a step further.  There wasn't really any similar
precedent for that to work off of that I noticed.  I'm agreeable to
change or restructuring if Kumar recommends re-using some standard as
set by the 4xx/EBC.

Paul.

> 
> > +			compatible = "wrs,epld-localbus";
> > +			#address-cells = <2>;
> > +			#size-cells = <1>;
> > +			reg = <0x5 0x0 0xc00000>;
> > +			ranges = <
> > +				0x0 0x0 0x5 0x000000 0x1fff	// LED disp.
> > +				0x1 0x0 0x5 0x100000 0x1fff	// switches
> > +				0x2 0x0 0x5 0x200000 0x1fff	// ID reg.
> > +				0x3 0x0 0x5 0x300000 0x1fff	// status reg.
> > +				0x4 0x0 0x5 0x400000 0x1fff	// reset reg.
> > +				0x5 0x0 0x5 0x500000 0x1fff	// Wind port
> > +				0x7 0x0 0x5 0x700000 0x1fff	// UART #1
> > +				0x8 0x0 0x5 0x800000 0x1fff	// UART #2
> > +				0x9 0x0 0x5 0x900000 0x1fff	// RTC
> > +				0xb 0x0 0x5 0xb00000 0x1fff	// EEPROM
> > +			>;
> 
> -- 
> David Gibson			| I'll have my music baroque, and my code
> david AT gibson.dropbear.id.au	| minimalist, thank you.  NOT _the_ _other_
> 				| _way_ _around_!
> http://www.ozlabs.org/~dgibson

Re: [PATCH 2/10] sbc8560: Add v1 device tree source for Wind River SBC8560 board

[David Gibson]

On Tue, Feb 05, 2008 at 09:44:23AM -0600, Kumar Gala wrote:
> 
> On Feb 4, 2008, at 8:40 PM, David Gibson wrote:
> 
> > On Fri, Feb 01, 2008 at 08:46:32AM -0600, Kumar Gala wrote:
> >>
> >> On Feb 1, 2008, at 1:54 AM, David Gibson wrote:
> >>
> >>> On Thu, Jan 24, 2008 at 06:41:24PM -0500, Paul Gortmaker wrote:
> > [snip]
> >>>> +		epld@5,0 {
> >>>
> >>> I'm not entirely convinced on this two-level representation.  I  
> >>> think
> >>> the FSL people need to get together and define a binding (or set of
> >>> bindings) for their various chipselect style external bus bridges.
> >>
> >> It seems reasonable if you had a FPGA off of the localbus to have a
> >> two level representation.  One for the localbus controller on the FSL
> >> part and the child to describe the FPGA.
> >>
> >> What are you expecting beyond what we have today?  I guess I'm asking
> >> what's missing from the localbus nodes we have?
> >
> > Sorry, I was probably misleading.  All I really meant is that I don't
> > know enough about these FSL bus bridge arrangements to assess if this
> > representation is the most sensible one.  I'm presuming that this
> > chipselect bridge unit is a more-or-less standard ASIC appearing on
> > lots of the FSL chips, so it would be nice to have a standard binding
> > for them, as we do for the roughly-equivalent EBC bridge on 4xx.
> 
> Is there a writeup for EBC?  I'll take a look at it and see if it  
> makes senses for the freescale 'localbus'.

Uh... not as such.  I'll try to write it up and add a binding to
b-w-o.txt next week when I'm back at work for real.  I wouldn't expect
it to be usable as is for the Freescale localbus, but it should be
pretty similar in spirit.

-- 
David Gibson			| I'll have my music baroque, and my code
david AT gibson.dropbear.id.au	| minimalist, thank you.  NOT _the_ _other_
				| _way_ _around_!
http://www.ozlabs.org/~dgibson