Re: ARCH=ppc -> ARCH=powerpc : help needed for dts file

[Benjamin Herrenschmidt <benh@kernel.crashing.org>]

> I also attach my current (not working) dts file attempt.  It is actually
> a modified mpc8540ads.dts file.
> 
> I now thinks that the ide-cs (hda) discovery or not depends on the cold
> or warm reboot.
> 
> Here are the patches for my config (MEIP_8540) relative to a vanilla
> linux-2.6.24.  I hacked the MPC8540ADS config. The PCI4520 is the
> multi-function chip from TI (dual-socket pc-card + iee1394 ohci and two-port
> phy)

 .../...

> +#ifdef CONFIG_MEIP_8540
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	// External 0 : nINTPFO
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	// External 1 : nINTRTC
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	// External 2 : nINTPLD
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	// External 3 : nINTSTX
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	// External 4 : nINTPHY
> +#if defined(CONFIG_PCI)
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),      /* External 5 : PCI4520 MFUNC 0 */
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),      /* External 6 : PCI4520 MFUNC 1 */
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),      /* External 7 : PCI4520 MFUNC 2 */
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),      /* External 8 : PCI4520 MFUNC 3 */
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),      /* External 9 : PCI4520 MFUNC 4 */
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),      /* External 10 : PCI4520 MFUNC 5 */
> +	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),      /* External 11 : PCI4520 MFUNC 6 */
> +#else
> +	0x0,						/* External  6: */
> +	0x0,						/* External  7: */
> +	0x0,						/* External  8: */
> +	0x0,						/* External  9: */
> +	0x0,						/* External 10: */
> +	0x0,						/* External 11: */
> +#endif
> +#else
>  	0x0,						/* External  0: */
>  #if defined(CONFIG_PCI)
>  	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	/* External 1: PCI slot 0 */
> @@ -77,6 +100,7 @@
>  	0x0,				/* External  9: */
>  	0x0,				/* External 10: */
>  	0x0,				/* External 11: */
> +#endif
>  };

Ok, so based on the above, I deduce that you have 12 external interrupt
sources:

0...4 are those nINT* things. They correspond apparently do discrete
devices on your board. You will have to create device nodes in your .dts
for these with the appropriate interrupts property for each of these.

The rest are ... hrm... weird. You -appear- to have 5 to 8 going to PCI,
to PIRQA...D. Do that mean that you have wired your connectors on the board
such that the interrupt does not depend on the actual slot number ?

Or are you doing some swizzling ?

Also, I would need to know how those external IRQs are connected to the MPIC,
I don't have the spec of that chip here. Hrm. Somebody from freescale can
help him here ?

It's also not clear to me what your interrupts 9 10 and 11 are since you
seem to only talk about PIRQA...D which is only 4 lines ..

So at this stage, that's not enough information. We need to know exactly how
you have wired things on your board, and somebody from fsl needs to tell
me how the ExtIrq are routed to the MPIC on that guy.

Once that's done, you seem to have grasped the interrupt map... for any
device or slot, you provide the mapping between idsel/pirq line on one side,
and mpic interrupt & sense on the other. For PCI, sense is always 1 for an
mpic so you mostly have to check your actual MPIC source numbers.

>From your .dts, I see you've been doing some swizzling of slots using
interrupts 1...4 ... do that correspond to EXTIRQ 5....8 ?

Ben.

>  
>  /* ************************************************************************ */
> --- ./arch/ppc/platforms/85xx/mpc85xx_ads_common.hbk	2008-01-24 22:58:37.000000000 +0000
> +++ ./arch/ppc/platforms/85xx/mpc85xx_ads_common.h	2008-02-20 16:36:07.000000000 +0000
> @@ -29,10 +29,17 @@
>  extern void mpc85xx_ads_map_io(void) __init;
>  
>  /* PCI interrupt controller */
> +#ifdef CONFIG_MEIP_8540
> +#define PIRQA		MPC85xx_IRQ_EXT5
> +#define PIRQB		MPC85xx_IRQ_EXT6
> +#define PIRQC		MPC85xx_IRQ_EXT7
> +#define PIRQD		MPC85xx_IRQ_EXT8
> +#else
>  #define PIRQA		MPC85xx_IRQ_EXT1
>  #define PIRQB		MPC85xx_IRQ_EXT2
>  #define PIRQC		MPC85xx_IRQ_EXT3
>  #define PIRQD		MPC85xx_IRQ_EXT4
> +#endif
>  
>  #define MPC85XX_PCI1_LOWER_IO	0x00000000
>  #define MPC85XX_PCI1_UPPER_IO	0x00ffffff