* RE: ML507 EDK 10.1
2008-06-02 14:35 ` John Linn
@ 2008-06-03 2:46 ` somshekar c kadam
2008-06-03 21:08 ` somshekar c kadam
` (2 subsequent siblings)
3 siblings, 0 replies; 6+ messages in thread
From: somshekar c kadam @ 2008-06-03 2:46 UTC (permalink / raw)
To: John Linn; +Cc: linuxppc-embedded
Hi John Linn,
Yes I have dowloaded the linux_support.tar.gz.
So if I get you correct I will use the bit stream provided by
linux_support.tar.gz clubbed with the zImage to create Ace file, I hope
that should work Ace file should boot the kernel. correct me if I am
wrong. Let create it and test it
As for ML403 we created zImage.dts and clubbed it with bit stream and
created ace file it botts up fine.
Thanks in Advance
Neelu
On Mon, 2008-06-02 at 08:35 -0600, John Linn wrote:
> Hi Neelu,
>
> The easiest way to get a good baseline with the board and the kernel is
> to use the bitstream for the board that we provide in the file,
> linux_support.tar.gz, on http://git.xilinx.com.
>
> In the PPC440 directory of the support file, there's a bit stream for
> the board. If you don't use a Xilinx probe to download to the board, you
> will need to create an ACE file from that bit stream, but it sounds like
> you know how to do that.
>
> I know the state of the Xilinx Git tree, but I don't know the state of
> Grant's for sure. We have baselined our Git tree such that you should be
> able to make it work quick and easy (that's our goal).
>
> To build arch/powerpc, the following commands should create zImage in
> the arch/powerpc/boot directory that can be used with the bitstream from
> the linux_support.tar.gz file. I am currently using the ELDK 4.1 tools
> to build the kernel.
>
> > make ARCH=powerpc ml507_defconfig
> > make ARCH=powerpc zImage
>
> We also provide a ramdisk image in the support file, you can build it
> also after copying the ramdisk images into the arch/powerpc/boot
> directory. The default command line of the kernel, in the ml507.dts
> file in the arch/powerpc/boot/dts directory, is setup to use the
> ramdisk.
>
> > make ARCH=powerpc zImage.initrd
>
> Hope that helps,
> John Linn
>
> -----Original Message-----
> From: linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org
> [mailto:linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org] On
> Behalf Of somshekar c kadam
> Sent: Monday, June 02, 2008 4:19 PM
> To: linuxppc-embedded@ozlabs.org
> Subject: ML507 EDK 10.1
>
> Hi All,
>
> Currently I am working with ML507 Base Reference design. I have
> installed Eval 10.1 edk I am bale to create ace file using xmd with base
> download.bit. and able to boot the board. Now I want to boot the board
> with Xilinx Linux kernel from Xilinx git tree. I am facing compilation
> problem with zImage.dts for ml507_defconfig.
>
>
>
>
> now I need to create ace file for Linux for ML507.
> I tried creating zImage.dts its failing. Kernel error see below
>
> Please help or give some pointers wherein I can compile zImge.dts. this
> is from latest git tree. Seems for me arch/powerpc wrapper code is
> broken. Please suggest.
> currently I have no bdi I need to stick to Ace compact Flash booting.
> Also bit confused where we have two git tree one is Xilinx git tree one
> more from Grant Likely which should I use ?
>
> Thanks In Advance
>
> Neelu
>
> ---------------------------------------------------
> WRAP arch/powerpc/boot/zImage.dts
> DTC: dts->dtb on file
> "/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/bo
> ot/dts/ml507.dts"
> objcopy: Unable to recognise the format of the input file `vmlinux'
> make[1]: *** [arch/powerpc/boot/zImage.dts] Error 1
> make: *** [zImage.dts] Error 2
>
>
>
>
> WIth Verbose =1
>
>
> /bin/sh
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/wrapper -c -o arch/powerpc/boot/zImage.dts -p dts -s
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts vmlinux
> + kernel=
> + ofile=zImage
> + platform=of
> + initrd=
> + dtb=
> + dts=
> + cacheit=
> + binary=
> + gzip=.gz
> + CROSS=
> + object=arch/powerpc/boot
> + objbin=arch/powerpc/boot
> + tmpdir=.
> + '[' 8 -gt 0 ']'
> + case "$1" in
> + cacheit=y
> + shift
> + '[' 7 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 6 -gt 0 ']'
> + ofile=arch/powerpc/boot/zImage.dts
> + shift
> + '[' 5 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 4 -gt 0 ']'
> + platform=dts
> + shift
> + '[' 3 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 2 -gt 0 ']'
> +
> dts=/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc
> /boot/dts/ml507.dts
> + shift
> + '[' 1 -gt 0 ']'
> + case "$1" in
> + '[' -z '' ']'
> + kernel=vmlinux
> + shift
> + '[' 0 -gt 0 ']'
> + '['
> -n
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts ']'
> + '[' '!'
> -r
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts -a -r
> arch/powerpc/boot/dts//home/neelu/xilinx/xilinx_gittree/test44/linux-2.6
> -xlnx/arch/powerpc/boot/dts/ml507.dts ']'
> + '[' -z '' ']'
> + dtb=dts.dtb
> + arch/powerpc/boot/dtc -O dtb -o dts.dtb -b
> 0
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts
> DTC: dts->dtb on file
> "/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/bo
> ot/dts/ml507.dts"
> + '[' -z vmlinux ']'
> + platformo=arch/powerpc/boot/dts.o
> + lds=arch/powerpc/boot/zImage.lds
> + ext=strip
> + objflags=-S
> + tmp=./zImage.24209.o
> + ksection=.kernel:vmlinux.strip
> + isection=.kernel:initrd
> + case "$platform" in
> ++ basename vmlinux
> + vmz=./vmlinux.strip
> + '[' -z y -o '!' -f ./vmlinux.strip.gz -o ./vmlinux.strip.gz -ot
> vmlinux ']'
> + objcopy -S vmlinux ./vmlinux.strip.24209
> objcopy: Unable to recognise the format of the input file `vmlinux'
> make[1]: *** [arch/powerpc/boot/zImage.dts] Error 1
> make: *** [zImage.dts] Error 2
>
>
>
>
>
> ------------------------------------------------------------------------
> ------------------
>
>
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>
>
> This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
^ permalink raw reply [flat|nested] 6+ messages in thread* RE: ML507 EDK 10.1
2008-06-02 14:35 ` John Linn
2008-06-03 2:46 ` somshekar c kadam
@ 2008-06-03 21:08 ` somshekar c kadam
2008-06-03 22:08 ` somshekar c kadam
2008-07-30 2:26 ` ML507 EDK 10.1 SP2 somshekar c kadam
3 siblings, 0 replies; 6+ messages in thread
From: somshekar c kadam @ 2008-06-03 21:08 UTC (permalink / raw)
To: John Linn; +Cc: linuxppc-embedded
Hi John Linn,
I tried using bit stream provided by linux_support.tar.gz,
It seems ace file still doesnt work, I created the ace file using bit
stream and zImage as you mentioned in the previuos mail. I dont know
wether there is something more for this to do.
I dont have parallel cable to check using xmd. shall I use bdi and
conenct and see this,
command i used to create ace file is shown below and put it on compact
flash at cfg6
Please suggest
Thanks In Advance
Neelu
xmd -tcl ../data/genace.tcl -hw ./ml507_ppc440_rtos.bit -elf ./zImage
-ace system.ace -board ml507
Xilinx Microprocessor Debug (XMD) Engine
Xilinx EDK 10.1 Build EDK_K.15
Copyright (c) 1995-2007 Xilinx, Inc. All rights reserved.
Executing user script : ../data/genace.tcl
#######################################################################
XMD GenACE utility. Generate SystemACE File from bit/elf/data Files
#######################################################################
Target Type not defined for Processor 1, Using default Target Type
ppc_hw
GenACE Options:
Board : ml507
Jtag Devs : xc5vfx70t
FPGA pos : 1
JPROG : false
HW File : ./ml507_ppc440_rtos.bit
ACE File : system.ace
nCPUs : 1
Processor ppc_hw_1 Information
Debug opt : -debugdevice devicenr 1 cpunr 1
ELF files : ./zImage
Start PC Address : 0x004007d8
############################################################
Converting Bitstream './ml507_ppc440_rtos.bit' to SVF file
'./ml507_ppc440_rtos.svf'
Executing 'impact -batch bit2svf.scr'
Copying ./ml507_ppc440_rtos.svf File to system.svf File
JTAG chain configuration
--------------------------------------------------
Device ID Code IR Length Part Name
1 032c6093 10 xc5vfx70t
PowerPC440 Processor Configuration
-------------------------------------
Version.............................0x7ff21910
User ID.............................0x00f00000
No of PC Breakpoints................4
No of Read Addr/Data Watchpoints....1
No of Write Addr/Data Watchpoints...1
User Defined Address Map to access Special PowerPC Features using XMD:
I-Cache (Data)........0x70000000 - 0x70007fff
I-Cache (TAG).........0x70008000 - 0x7000ffff
D-Cache (Data)........0x78000000 - 0x78007fff
D-Cache (TAG).........0x78008000 - 0x7800ffff
DCR...................0x78020000 - 0x78020fff
TLB...................0x70020000 - 0x70023fff
############################################################
Converting ELF file './zImage' to SVF file './zImage.svf'
JTAG chain configuration
--------------------------------------------------
Device ID Code IR Length Part Name
1 032c6093 10 xc5vfx70t
PowerPC440 Processor Configuration
-------------------------------------
Version.............................0x7ff21910
User ID.............................0x00f00000
No of PC Breakpoints................4
No of Read Addr/Data Watchpoints....1
No of Write Addr/Data Watchpoints...1
User Defined Address Map to access Special PowerPC Features using XMD:
I-Cache (Data)........0x70000000 - 0x70007fff
I-Cache (TAG).........0x70008000 - 0x7000ffff
D-Cache (Data)........0x78000000 - 0x78007fff
D-Cache (TAG).........0x78008000 - 0x7800ffff
DCR...................0x78020000 - 0x78020fff
TLB...................0x70020000 - 0x70023fff
Copying ./zImage.svf File to system.svf File
############################################################
Writing Processor JTAG "continue" command to SVF file 'sw_suffix.svf'
JTAG chain configuration
--------------------------------------------------
Device ID Code IR Length Part Name
1 032c6093 10 xc5vfx70t
PowerPC440 Processor Configuration
-------------------------------------
Version.............................0x7ff21910
User ID.............................0x00f00000
No of PC Breakpoints................4
No of Read Addr/Data Watchpoints....1
No of Write Addr/Data Watchpoints...1
User Defined Address Map to access Special PowerPC Features using XMD:
I-Cache (Data)........0x70000000 - 0x70007fff
I-Cache (TAG).........0x70008000 - 0x7000ffff
D-Cache (Data)........0x78000000 - 0x78007fff
D-Cache (TAG).........0x78008000 - 0x7800ffff
DCR...................0x78020000 - 0x78020fff
TLB...................0x70020000 - 0x70023fff
Info:Processor started. Type "stop" to stop processor
RUNNING>
############################################################
Converting SVF file 'system.svf' to SystemACE file 'system.ace'
Executing 'impact -batch svf2ace.scr'
SystemACE file 'system.ace' created successfully
On Mon, 2008-06-02 at 08:35 -0600, John Linn wrote:
> Hi Neelu,
>
> The easiest way to get a good baseline with the board and the kernel is
> to use the bitstream for the board that we provide in the file,
> linux_support.tar.gz, on http://git.xilinx.com.
>
> In the PPC440 directory of the support file, there's a bit stream for
> the board. If you don't use a Xilinx probe to download to the board, you
> will need to create an ACE file from that bit stream, but it sounds like
> you know how to do that.
>
> I know the state of the Xilinx Git tree, but I don't know the state of
> Grant's for sure. We have baselined our Git tree such that you should be
> able to make it work quick and easy (that's our goal).
>
> To build arch/powerpc, the following commands should create zImage in
> the arch/powerpc/boot directory that can be used with the bitstream from
> the linux_support.tar.gz file. I am currently using the ELDK 4.1 tools
> to build the kernel.
>
> > make ARCH=powerpc ml507_defconfig
> > make ARCH=powerpc zImage
>
> We also provide a ramdisk image in the support file, you can build it
> also after copying the ramdisk images into the arch/powerpc/boot
> directory. The default command line of the kernel, in the ml507.dts
> file in the arch/powerpc/boot/dts directory, is setup to use the
> ramdisk.
>
> > make ARCH=powerpc zImage.initrd
>
> Hope that helps,
> John Linn
>
> -----Original Message-----
> From: linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org
> [mailto:linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org] On
> Behalf Of somshekar c kadam
> Sent: Monday, June 02, 2008 4:19 PM
> To: linuxppc-embedded@ozlabs.org
> Subject: ML507 EDK 10.1
>
> Hi All,
>
> Currently I am working with ML507 Base Reference design. I have
> installed Eval 10.1 edk I am bale to create ace file using xmd with base
> download.bit. and able to boot the board. Now I want to boot the board
> with Xilinx Linux kernel from Xilinx git tree. I am facing compilation
> problem with zImage.dts for ml507_defconfig.
>
>
>
>
> now I need to create ace file for Linux for ML507.
> I tried creating zImage.dts its failing. Kernel error see below
>
> Please help or give some pointers wherein I can compile zImge.dts. this
> is from latest git tree. Seems for me arch/powerpc wrapper code is
> broken. Please suggest.
> currently I have no bdi I need to stick to Ace compact Flash booting.
> Also bit confused where we have two git tree one is Xilinx git tree one
> more from Grant Likely which should I use ?
>
> Thanks In Advance
>
> Neelu
>
> ---------------------------------------------------
> WRAP arch/powerpc/boot/zImage.dts
> DTC: dts->dtb on file
> "/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/bo
> ot/dts/ml507.dts"
> objcopy: Unable to recognise the format of the input file `vmlinux'
> make[1]: *** [arch/powerpc/boot/zImage.dts] Error 1
> make: *** [zImage.dts] Error 2
>
>
>
>
> WIth Verbose =1
>
>
> /bin/sh
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/wrapper -c -o arch/powerpc/boot/zImage.dts -p dts -s
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts vmlinux
> + kernel=
> + ofile=zImage
> + platform=of
> + initrd=
> + dtb=
> + dts=
> + cacheit=
> + binary=
> + gzip=.gz
> + CROSS=
> + object=arch/powerpc/boot
> + objbin=arch/powerpc/boot
> + tmpdir=.
> + '[' 8 -gt 0 ']'
> + case "$1" in
> + cacheit=y
> + shift
> + '[' 7 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 6 -gt 0 ']'
> + ofile=arch/powerpc/boot/zImage.dts
> + shift
> + '[' 5 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 4 -gt 0 ']'
> + platform=dts
> + shift
> + '[' 3 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 2 -gt 0 ']'
> +
> dts=/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc
> /boot/dts/ml507.dts
> + shift
> + '[' 1 -gt 0 ']'
> + case "$1" in
> + '[' -z '' ']'
> + kernel=vmlinux
> + shift
> + '[' 0 -gt 0 ']'
> + '['
> -n
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts ']'
> + '[' '!'
> -r
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts -a -r
> arch/powerpc/boot/dts//home/neelu/xilinx/xilinx_gittree/test44/linux-2.6
> -xlnx/arch/powerpc/boot/dts/ml507.dts ']'
> + '[' -z '' ']'
> + dtb=dts.dtb
> + arch/powerpc/boot/dtc -O dtb -o dts.dtb -b
> 0
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts
> DTC: dts->dtb on file
> "/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/bo
> ot/dts/ml507.dts"
> + '[' -z vmlinux ']'
> + platformo=arch/powerpc/boot/dts.o
> + lds=arch/powerpc/boot/zImage.lds
> + ext=strip
> + objflags=-S
> + tmp=./zImage.24209.o
> + ksection=.kernel:vmlinux.strip
> + isection=.kernel:initrd
> + case "$platform" in
> ++ basename vmlinux
> + vmz=./vmlinux.strip
> + '[' -z y -o '!' -f ./vmlinux.strip.gz -o ./vmlinux.strip.gz -ot
> vmlinux ']'
> + objcopy -S vmlinux ./vmlinux.strip.24209
> objcopy: Unable to recognise the format of the input file `vmlinux'
> make[1]: *** [arch/powerpc/boot/zImage.dts] Error 1
> make: *** [zImage.dts] Error 2
>
>
>
>
>
> ------------------------------------------------------------------------
> ------------------
>
>
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>
>
> This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
^ permalink raw reply [flat|nested] 6+ messages in thread* RE: ML507 EDK 10.1
2008-06-02 14:35 ` John Linn
2008-06-03 2:46 ` somshekar c kadam
2008-06-03 21:08 ` somshekar c kadam
@ 2008-06-03 22:08 ` somshekar c kadam
2008-07-30 2:26 ` ML507 EDK 10.1 SP2 somshekar c kadam
3 siblings, 0 replies; 6+ messages in thread
From: somshekar c kadam @ 2008-06-03 22:08 UTC (permalink / raw)
To: John Linn; +Cc: linuxppc-embedded
Hi John Linn,
Ignore prvious mail now I ma bale to get Linux up and running
thanks for all the support, was able to create ace file using the bit
stream of linux_support it boots perfectly.
Thanks a lot for all the help
Regards
Neelu
On Mon, 2008-06-02 at 08:35 -0600, John Linn wrote:
> Hi Neelu,
>
> The easiest way to get a good baseline with the board and the kernel is
> to use the bitstream for the board that we provide in the file,
> linux_support.tar.gz, on http://git.xilinx.com.
>
> In the PPC440 directory of the support file, there's a bit stream for
> the board. If you don't use a Xilinx probe to download to the board, you
> will need to create an ACE file from that bit stream, but it sounds like
> you know how to do that.
>
> I know the state of the Xilinx Git tree, but I don't know the state of
> Grant's for sure. We have baselined our Git tree such that you should be
> able to make it work quick and easy (that's our goal).
>
> To build arch/powerpc, the following commands should create zImage in
> the arch/powerpc/boot directory that can be used with the bitstream from
> the linux_support.tar.gz file. I am currently using the ELDK 4.1 tools
> to build the kernel.
>
> > make ARCH=powerpc ml507_defconfig
> > make ARCH=powerpc zImage
>
> We also provide a ramdisk image in the support file, you can build it
> also after copying the ramdisk images into the arch/powerpc/boot
> directory. The default command line of the kernel, in the ml507.dts
> file in the arch/powerpc/boot/dts directory, is setup to use the
> ramdisk.
>
> > make ARCH=powerpc zImage.initrd
>
> Hope that helps,
> John Linn
>
> -----Original Message-----
> From: linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org
> [mailto:linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org] On
> Behalf Of somshekar c kadam
> Sent: Monday, June 02, 2008 4:19 PM
> To: linuxppc-embedded@ozlabs.org
> Subject: ML507 EDK 10.1
>
> Hi All,
>
> Currently I am working with ML507 Base Reference design. I have
> installed Eval 10.1 edk I am bale to create ace file using xmd with base
> download.bit. and able to boot the board. Now I want to boot the board
> with Xilinx Linux kernel from Xilinx git tree. I am facing compilation
> problem with zImage.dts for ml507_defconfig.
>
>
>
>
> now I need to create ace file for Linux for ML507.
> I tried creating zImage.dts its failing. Kernel error see below
>
> Please help or give some pointers wherein I can compile zImge.dts. this
> is from latest git tree. Seems for me arch/powerpc wrapper code is
> broken. Please suggest.
> currently I have no bdi I need to stick to Ace compact Flash booting.
> Also bit confused where we have two git tree one is Xilinx git tree one
> more from Grant Likely which should I use ?
>
> Thanks In Advance
>
> Neelu
>
> ---------------------------------------------------
> WRAP arch/powerpc/boot/zImage.dts
> DTC: dts->dtb on file
> "/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/bo
> ot/dts/ml507.dts"
> objcopy: Unable to recognise the format of the input file `vmlinux'
> make[1]: *** [arch/powerpc/boot/zImage.dts] Error 1
> make: *** [zImage.dts] Error 2
>
>
>
>
> WIth Verbose =1
>
>
> /bin/sh
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/wrapper -c -o arch/powerpc/boot/zImage.dts -p dts -s
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts vmlinux
> + kernel=
> + ofile=zImage
> + platform=of
> + initrd=
> + dtb=
> + dts=
> + cacheit=
> + binary=
> + gzip=.gz
> + CROSS=
> + object=arch/powerpc/boot
> + objbin=arch/powerpc/boot
> + tmpdir=.
> + '[' 8 -gt 0 ']'
> + case "$1" in
> + cacheit=y
> + shift
> + '[' 7 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 6 -gt 0 ']'
> + ofile=arch/powerpc/boot/zImage.dts
> + shift
> + '[' 5 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 4 -gt 0 ']'
> + platform=dts
> + shift
> + '[' 3 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 2 -gt 0 ']'
> +
> dts=/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc
> /boot/dts/ml507.dts
> + shift
> + '[' 1 -gt 0 ']'
> + case "$1" in
> + '[' -z '' ']'
> + kernel=vmlinux
> + shift
> + '[' 0 -gt 0 ']'
> + '['
> -n
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts ']'
> + '[' '!'
> -r
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts -a -r
> arch/powerpc/boot/dts//home/neelu/xilinx/xilinx_gittree/test44/linux-2.6
> -xlnx/arch/powerpc/boot/dts/ml507.dts ']'
> + '[' -z '' ']'
> + dtb=dts.dtb
> + arch/powerpc/boot/dtc -O dtb -o dts.dtb -b
> 0
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts
> DTC: dts->dtb on file
> "/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/bo
> ot/dts/ml507.dts"
> + '[' -z vmlinux ']'
> + platformo=arch/powerpc/boot/dts.o
> + lds=arch/powerpc/boot/zImage.lds
> + ext=strip
> + objflags=-S
> + tmp=./zImage.24209.o
> + ksection=.kernel:vmlinux.strip
> + isection=.kernel:initrd
> + case "$platform" in
> ++ basename vmlinux
> + vmz=./vmlinux.strip
> + '[' -z y -o '!' -f ./vmlinux.strip.gz -o ./vmlinux.strip.gz -ot
> vmlinux ']'
> + objcopy -S vmlinux ./vmlinux.strip.24209
> objcopy: Unable to recognise the format of the input file `vmlinux'
> make[1]: *** [arch/powerpc/boot/zImage.dts] Error 1
> make: *** [zImage.dts] Error 2
>
>
>
>
>
> ------------------------------------------------------------------------
> ------------------
>
>
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>
>
> This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
^ permalink raw reply [flat|nested] 6+ messages in thread
* ML507 EDK 10.1 SP2
2008-06-02 14:35 ` John Linn
` (2 preceding siblings ...)
2008-06-03 22:08 ` somshekar c kadam
@ 2008-07-30 2:26 ` somshekar c kadam
3 siblings, 0 replies; 6+ messages in thread
From: somshekar c kadam @ 2008-07-30 2:26 UTC (permalink / raw)
To: John Linn; +Cc: skaushik, nbhat, pnarasim, linuxppc-embedded
Hi John Linn,
We are using ML507 EDK 10.1 with latest SP2.
We have took your help in getting up the Xilinx git kernel up on ML507
using bsb image donwload.bit from xilinx website and dts file part of
the kernel. The kernel boots successfully. thanks for all your support.
Well we now want to modify bsb image by creating new download.bit using
EDK 10.1 SP2 and generate dts file for it.
Problem now we are facing is we follow the steps mentioned XIlinx ML507
pdf to create donwload.bit and generate dts file for it. using the same
xilinx kernel but the board doesn't boot.
Can you throw some light on any specific steps we are missing apart from
the pdf mentioned to create bsb image download.bit and corresponding dts
file.
Just we need to use uartlite instead of 16650 uart.
Also we are trying on ML403 we are not able to create a sample
donwload.bit which boots.
Please mention any steps we are missing or any pointers will help as we
are stuck in this problem from long.
For ml403 we even tried older edk 9.1 sp2 , 8.1 sp2 and 7.1 sp2 neither
works .
Waiting for your inputs
Thanks In advance
Regards
Neelu
On Mon, 2008-06-02 at 08:35 -0600, John Linn wrote:
> Hi Neelu,
>
> The easiest way to get a good baseline with the board and the kernel is
> to use the bitstream for the board that we provide in the file,
> linux_support.tar.gz, on http://git.xilinx.com.
>
> In the PPC440 directory of the support file, there's a bit stream for
> the board. If you don't use a Xilinx probe to download to the board, you
> will need to create an ACE file from that bit stream, but it sounds like
> you know how to do that.
>
> I know the state of the Xilinx Git tree, but I don't know the state of
> Grant's for sure. We have baselined our Git tree such that you should be
> able to make it work quick and easy (that's our goal).
>
> To build arch/powerpc, the following commands should create zImage in
> the arch/powerpc/boot directory that can be used with the bitstream from
> the linux_support.tar.gz file. I am currently using the ELDK 4.1 tools
> to build the kernel.
>
> > make ARCH=powerpc ml507_defconfig
> > make ARCH=powerpc zImage
>
> We also provide a ramdisk image in the support file, you can build it
> also after copying the ramdisk images into the arch/powerpc/boot
> directory. The default command line of the kernel, in the ml507.dts
> file in the arch/powerpc/boot/dts directory, is setup to use the
> ramdisk.
>
> > make ARCH=powerpc zImage.initrd
>
> Hope that helps,
> John Linn
>
> -----Original Message-----
> From: linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org
> [mailto:linuxppc-embedded-bounces+john.linn=xilinx.com@ozlabs.org] On
> Behalf Of somshekar c kadam
> Sent: Monday, June 02, 2008 4:19 PM
> To: linuxppc-embedded@ozlabs.org
> Subject: ML507 EDK 10.1
>
> Hi All,
>
> Currently I am working with ML507 Base Reference design. I have
> installed Eval 10.1 edk I am bale to create ace file using xmd with base
> download.bit. and able to boot the board. Now I want to boot the board
> with Xilinx Linux kernel from Xilinx git tree. I am facing compilation
> problem with zImage.dts for ml507_defconfig.
>
>
>
>
> now I need to create ace file for Linux for ML507.
> I tried creating zImage.dts its failing. Kernel error see below
>
> Please help or give some pointers wherein I can compile zImge.dts. this
> is from latest git tree. Seems for me arch/powerpc wrapper code is
> broken. Please suggest.
> currently I have no bdi I need to stick to Ace compact Flash booting.
> Also bit confused where we have two git tree one is Xilinx git tree one
> more from Grant Likely which should I use ?
>
> Thanks In Advance
>
> Neelu
>
> ---------------------------------------------------
> WRAP arch/powerpc/boot/zImage.dts
> DTC: dts->dtb on file
> "/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/bo
> ot/dts/ml507.dts"
> objcopy: Unable to recognise the format of the input file `vmlinux'
> make[1]: *** [arch/powerpc/boot/zImage.dts] Error 1
> make: *** [zImage.dts] Error 2
>
>
>
>
> WIth Verbose =1
>
>
> /bin/sh
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/wrapper -c -o arch/powerpc/boot/zImage.dts -p dts -s
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts vmlinux
> + kernel=
> + ofile=zImage
> + platform=of
> + initrd=
> + dtb=
> + dts=
> + cacheit=
> + binary=
> + gzip=.gz
> + CROSS=
> + object=arch/powerpc/boot
> + objbin=arch/powerpc/boot
> + tmpdir=.
> + '[' 8 -gt 0 ']'
> + case "$1" in
> + cacheit=y
> + shift
> + '[' 7 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 6 -gt 0 ']'
> + ofile=arch/powerpc/boot/zImage.dts
> + shift
> + '[' 5 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 4 -gt 0 ']'
> + platform=dts
> + shift
> + '[' 3 -gt 0 ']'
> + case "$1" in
> + shift
> + '[' 2 -gt 0 ']'
> +
> dts=/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc
> /boot/dts/ml507.dts
> + shift
> + '[' 1 -gt 0 ']'
> + case "$1" in
> + '[' -z '' ']'
> + kernel=vmlinux
> + shift
> + '[' 0 -gt 0 ']'
> + '['
> -n
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts ']'
> + '[' '!'
> -r
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts -a -r
> arch/powerpc/boot/dts//home/neelu/xilinx/xilinx_gittree/test44/linux-2.6
> -xlnx/arch/powerpc/boot/dts/ml507.dts ']'
> + '[' -z '' ']'
> + dtb=dts.dtb
> + arch/powerpc/boot/dtc -O dtb -o dts.dtb -b
> 0
> /home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/boo
> t/dts/ml507.dts
> DTC: dts->dtb on file
> "/home/neelu/xilinx/xilinx_gittree/test44/linux-2.6-xlnx/arch/powerpc/bo
> ot/dts/ml507.dts"
> + '[' -z vmlinux ']'
> + platformo=arch/powerpc/boot/dts.o
> + lds=arch/powerpc/boot/zImage.lds
> + ext=strip
> + objflags=-S
> + tmp=./zImage.24209.o
> + ksection=.kernel:vmlinux.strip
> + isection=.kernel:initrd
> + case "$platform" in
> ++ basename vmlinux
> + vmz=./vmlinux.strip
> + '[' -z y -o '!' -f ./vmlinux.strip.gz -o ./vmlinux.strip.gz -ot
> vmlinux ']'
> + objcopy -S vmlinux ./vmlinux.strip.24209
> objcopy: Unable to recognise the format of the input file `vmlinux'
> make[1]: *** [arch/powerpc/boot/zImage.dts] Error 1
> make: *** [zImage.dts] Error 2
>
>
>
>
>
> ------------------------------------------------------------------------
> ------------------
>
>
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>
>
> This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
^ permalink raw reply [flat|nested] 6+ messages in thread