* [PATCH 0/4][Version 3] MPC5121 Updates
@ 2008-07-09 20:54 John Rigby
2008-07-09 20:54 ` [PATCH 1/4][Version 3] MPC5121 Update MPC5121ADS device tree John Rigby
0 siblings, 1 reply; 5+ messages in thread
From: John Rigby @ 2008-07-09 20:54 UTC (permalink / raw)
To: linuxppc-dev; +Cc: John Rigby
The following patches contain updates for MPC5121
1/4
Updates the device tree.
Addresses all comments received.
2/4
Adds a clock driver. Cleanup based on input from Stephen Rothwell,
and Grant Likely. Also now uses the clock driver in
arch/powerpc/kernel/clock.c instead of exporting api's directly.
3/4
Adds support for generic boards. This is nearly identical to
David Jander's patch but does not delete the ADS board option.
ADS is not a candidate for generic since it has an on board
cpld that does pci interrupt routing.
4/4
Adds support for the CPLD on the MPC5121ADS board.
Some minor changes based on input from Grant Likely.
This patchset does not include PCI support. PCI support for 5121
needs mpc83xx_add_bridge to be moved to sysdev/fsl_pci.c. That
change is in a different patch set. I'll submit a 5121 PCI patch
after that different patch set gets committed.
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/4][Version 3] MPC5121 Update MPC5121ADS device tree
2008-07-09 20:54 [PATCH 0/4][Version 3] MPC5121 Updates John Rigby
@ 2008-07-09 20:54 ` John Rigby
2008-07-09 20:54 ` [PATCH 2/4][Version 3] MPC5121 clock driver John Rigby
0 siblings, 1 reply; 5+ messages in thread
From: John Rigby @ 2008-07-09 20:54 UTC (permalink / raw)
To: linuxppc-dev; +Cc: John Rigby
Current device tree is only bare bones. This patch
adds nodes to make it a complete tree for MPC5121ads.
Added nodes include:
mbx - opengl coprocessor
nfc - nand flash controller
cpld-pic - on board cpld
rtc
clock - clock control
pmc - power management control
gpio
mscan - can module
i2c
axe - audio coprocessor
display - display interface unit
mdio
ethernet
usb
ioctl - pin config
pata
ac97 - PSC configured as AC97
pscfifo - psc fifo configuration
dma
pci
Fix typo in header changing MDS to ADS.
Add a compatible property of the form "fsl,mpc5121-..."
to nodes missing one.
Changed localbus compatible to fsl,mpc5121-localbus, this does
not break anything because the only code that uses it finds it
via the node name, not compatible.
Signed-off-by: John Rigby <jrigby@freescale.com>
---
arch/powerpc/boot/dts/mpc5121ads.dts | 310 ++++++++++++++++++++++++++++++++--
1 files changed, 299 insertions(+), 11 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc5121ads.dts b/arch/powerpc/boot/dts/mpc5121ads.dts
index 94ad7b2..1f9036c 100644
--- a/arch/powerpc/boot/dts/mpc5121ads.dts
+++ b/arch/powerpc/boot/dts/mpc5121ads.dts
@@ -1,7 +1,7 @@
/*
- * MPC5121E MDS Device Tree Source
+ * MPC5121E ADS Device Tree Source
*
- * Copyright 2007 Freescale Semiconductor Inc.
+ * Copyright 2007,2008 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
@@ -17,6 +17,10 @@
#address-cells = <1>;
#size-cells = <1>;
+ aliases {
+ pci = &pci;
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
@@ -39,8 +43,41 @@
reg = <0x00000000 0x10000000>; // 256MB at 0
};
+ mbx@20000000 {
+ compatible = "fsl,mpc5121-mbx";
+ reg = <0x20000000 0x4000>;
+ interrupts = <66 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ sram@30000000 {
+ compatible = "fsl,mpc5121-sram";
+ reg = <0x30000000 0x20000>; // 128K at 0x30000000
+ };
+
+ nfc@40000000 {
+ compatible = "fsl,mpc5121-nfc";
+ reg = <0x40000000 0x100000>; // 1M at 0x40000000
+ interrupts = <6 8>;
+ interrupt-parent = < &ipic >;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ bank-width = <1>;
+ // ADS has two Hynix 512MB Nand flash chips in a single
+ // stacked package .
+ chips = <2>;
+ nand0@0 {
+ label = "nand0";
+ reg = <0x00000000 0x02000000>; // first 32 MB of chip 0
+ };
+ nand1@20000000 {
+ label = "nand1";
+ reg = <0x20000000 0x02000000>; // first 32 MB of chip 1
+ };
+ };
+
localbus@80000020 {
- compatible = "fsl,mpc5121ads-localbus";
+ compatible = "fsl,mpc5121-localbus";
#address-cells = <2>;
#size-cells = <1>;
reg = <0x80000020 0x40>;
@@ -51,14 +88,51 @@
flash@0,0 {
compatible = "cfi-flash";
reg = <0 0x0 0x4000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
bank-width = <4>;
- device-width = <1>;
+ device-width = <2>;
+ protected@0 {
+ label = "protected";
+ reg = <0x00000000 0x00040000>; // first sector is protected
+ read-only;
+ };
+ filesystem@40000 {
+ label = "filesystem";
+ reg = <0x00040000 0x03c00000>; // 60M for filesystem
+ };
+ kernel@3c40000 {
+ label = "kernel";
+ reg = <0x03c40000 0x00280000>; // 2.5M for kernel
+ };
+ device-tree@3ec0000 {
+ label = "device-tree";
+ reg = <0x03ec0000 0x00040000>; // one sector for device tree
+ };
+ u-boot@3f00000 {
+ label = "u-boot";
+ reg = <0x03f00000 0x00100000>; // 1M for u-boot
+ read-only;
+ };
};
board-control@2,0 {
compatible = "fsl,mpc5121ads-cpld";
reg = <0x2 0x0 0x8000>;
};
+
+ cpld_pic: pic@2,a {
+ compatible = "fsl,mpc5121ads-cpld-pic";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x2 0xa 0x5>;
+ interrupt-parent = < &ipic >;
+ // irq routing
+ // all irqs but touch screen are routed to irq0 (ipic 48)
+ // touch screen is statically routed to irq1 (ipic 17)
+ // so don't use it here
+ interrupts = <48 0x8>;
+ };
};
soc@80000000 {
@@ -85,38 +159,252 @@
reg = <0xc00 0x100>;
};
- // 512x PSCs are not 52xx PSCs compatible
+ rtc@a00 { // Real time clock
+ compatible = "fsl,mpc5121-rtc";
+ reg = <0xa00 0x100>;
+ interrupts = <79 0x8 80 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ clock@f00 { // Clock control
+ compatible = "fsl,mpc5121-clock";
+ reg = <0xf00 0x100>;
+ };
+
+ pmc@1000{ //Power Management Controller
+ compatible = "fsl,mpc5121-pmc";
+ reg = <0x1000 0x100>;
+ interrupts = <83 0x2>;
+ interrupt-parent = < &ipic >;
+ };
+
+ gpio@1100 {
+ compatible = "fsl,mpc5121-gpio";
+ reg = <0x1100 0x100>;
+ interrupts = <78 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ mscan@1300 {
+ compatible = "fsl,mpc5121-mscan";
+ cell-index = <0>;
+ interrupts = <12 0x8>;
+ interrupt-parent = < &ipic >;
+ reg = <0x1300 0x80>;
+ };
+
+ mscan@1380 {
+ compatible = "fsl,mpc5121-mscan";
+ cell-index = <1>;
+ interrupts = <13 0x8>;
+ interrupt-parent = < &ipic >;
+ reg = <0x1380 0x80>;
+ };
+
+ i2c@1700 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5121-i2c", "fsl-i2c";
+ cell-index = <0>;
+ reg = <0x1700 0x20>;
+ interrupts = <9 0x8>;
+ interrupt-parent = < &ipic >;
+ fsl5200-clocking;
+ };
+
+ i2c@1720 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5121-i2c", "fsl-i2c";
+ cell-index = <1>;
+ reg = <0x1720 0x20>;
+ interrupts = <10 0x8>;
+ interrupt-parent = < &ipic >;
+ fsl5200-clocking;
+ };
+
+ i2c@1740 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5121-i2c", "fsl-i2c";
+ cell-index = <2>;
+ reg = <0x1740 0x20>;
+ interrupts = <11 0x8>;
+ interrupt-parent = < &ipic >;
+ fsl5200-clocking;
+ };
+
+ i2ccontrol@1760 {
+ compatible = "fsl,mpc5121-i2c-ctrl";
+ reg = <0x1760 0x8>;
+ };
+
+ axe@2000 {
+ compatible = "fsl,mpc5121-axe";
+ reg = <0x2000 0x100>;
+ interrupts = <42 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ display@2100 {
+ compatible = "fsl,mpc5121-diu", "fsl-diu";
+ reg = <0x2100 0x100>;
+ interrupts = <64 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ mdio@2800 {
+ compatible = "fsl,mpc5121-fec-mdio";
+ reg = <0x2800 0x800>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy: ethernet-phy@0 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ ethernet@2800 {
+ device_type = "network";
+ compatible = "fsl,mpc5121-fec";
+ reg = <0x2800 0x800>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <4 0x8>;
+ interrupt-parent = < &ipic >;
+ phy-handle = < &phy >;
+ fsl,align-tx-packets = <4>;
+ };
+
+ // 5121e has two dr usb modules
+ // mpc5121_ads only uses USB0
+
+ // USB1 using external ULPI PHY
+ //usb@3000 {
+ // compatible = "fsl,mpc5121-usb2-dr", "fsl-usb2-dr";
+ // reg = <0x3000 0x1000>;
+ // #address-cells = <1>;
+ // #size-cells = <0>;
+ // interrupt-parent = < &ipic >;
+ // interrupts = <43 0x8>;
+ // dr_mode = "otg";
+ // phy_type = "ulpi";
+ // port1;
+ //};
+
+ // USB0 using internal UTMI PHY
+ usb@4000 {
+ compatible = "fsl,mpc5121-usb2-dr", "fsl-usb2-dr";
+ reg = <0x4000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = < &ipic >;
+ interrupts = <44 0x8>;
+ dr_mode = "otg";
+ phy_type = "utmi_wide";
+ port0;
+ };
+
+ // IO control
+ ioctl@a000 {
+ compatible = "fsl,mpc5121-ioctl";
+ reg = <0xA000 0x1000>;
+ };
+
+ pata@10200 {
+ compatible = "fsl,mpc5121-pata";
+ reg = <0x10200 0x100>;
+ interrupts = <5 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ // 512x PSCs are not 52xx PSC compatible
// PSC3 serial port A aka ttyPSC0
serial@11300 {
device_type = "serial";
- compatible = "fsl,mpc5121-psc-uart";
+ compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
// Logical port assignment needed until driver
// learns to use aliases
port-number = <0>;
cell-index = <3>;
reg = <0x11300 0x100>;
- interrupts = <0x28 0x8>; // actually the fifo irq
+ interrupts = <40 0x8>;
interrupt-parent = < &ipic >;
+ rx-fifo-size = <16>;
+ tx-fifo-size = <16>;
};
// PSC4 serial port B aka ttyPSC1
serial@11400 {
device_type = "serial";
- compatible = "fsl,mpc5121-psc-uart";
+ compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
// Logical port assignment needed until driver
// learns to use aliases
port-number = <1>;
cell-index = <4>;
reg = <0x11400 0x100>;
- interrupts = <0x28 0x8>; // actually the fifo irq
+ interrupts = <40 0x8>;
interrupt-parent = < &ipic >;
+ rx-fifo-size = <16>;
+ tx-fifo-size = <16>;
};
- pscsfifo@11f00 {
+ // PSC5 in ac97 mode
+ ac97@11500 {
+ compatible = "fsl,mpc5121-psc-ac97", "fsl,mpc5121-psc";
+ cell-index = <5>;
+ reg = <0x11500 0x100>;
+ interrupts = <40 0x8>;
+ interrupt-parent = < &ipic >;
+ fsl,mode = "ac97-slave";
+ rx-fifo-size = <384>;
+ tx-fifo-size = <384>;
+ };
+
+ pscfifo@11f00 {
compatible = "fsl,mpc5121-psc-fifo";
reg = <0x11f00 0x100>;
- interrupts = <0x28 0x8>;
+ interrupts = <40 0x8>;
interrupt-parent = < &ipic >;
};
+
+ dma@14000 {
+ compatible = "fsl,mpc5121-dma2";
+ reg = <0x14000 0x1800>;
+ interrupts = <65 0x8>;
+ interrupt-parent = < &ipic >;
+ };
+
+ };
+
+ pci: pci@80008500 {
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+ // IDSEL 0x15 - Slot 1 PCI
+ 0xa800 0x0 0x0 0x1 &cpld_pic 0x0 0x8
+ 0xa800 0x0 0x0 0x2 &cpld_pic 0x1 0x8
+ 0xa800 0x0 0x0 0x3 &cpld_pic 0x2 0x8
+ 0xa800 0x0 0x0 0x4 &cpld_pic 0x3 0x8
+
+ // IDSEL 0x16 - Slot 2 MiniPCI
+ 0xb000 0x0 0x0 0x1 &cpld_pic 0x4 0x8
+ 0xb000 0x0 0x0 0x2 &cpld_pic 0x5 0x8
+
+ // IDSEL 0x17 - Slot 3 MiniPCI
+ 0xb800 0x0 0x0 0x1 &cpld_pic 0x6 0x8
+ 0xb800 0x0 0x0 0x2 &cpld_pic 0x7 0x8
+ >;
+ interrupt-parent = < &ipic >;
+ interrupts = <1 0x8>;
+ bus-range = <0 0>;
+ ranges = <0x42000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
+ 0x02000000 0x0 0xb0000000 0xb0000000 0x0 0x10000000
+ 0x01000000 0x0 0x00000000 0x84000000 0x0 0x01000000>;
+ clock-frequency = <0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0x80008500 0x100>;
+ compatible = "fsl,mpc5121-pci";
+ device_type = "pci";
};
};
--
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/4][Version 3] MPC5121 clock driver
2008-07-09 20:54 ` [PATCH 1/4][Version 3] MPC5121 Update MPC5121ADS device tree John Rigby
@ 2008-07-09 20:54 ` John Rigby
2008-07-09 20:54 ` [PATCH 3/4][Version 3] MPC5121 Add generic board support John Rigby
0 siblings, 1 reply; 5+ messages in thread
From: John Rigby @ 2008-07-09 20:54 UTC (permalink / raw)
To: linuxppc-dev; +Cc: John Rigby
Plugs into the generic powerpc clock driver in
arch/powerpc/kernel/clock.c
The following subset of clk_interface is implemented:
clk_get, clk_put: get clock via name, release clock
clk_enable, clk_disable: enable or disable clock
clk_get_rate: get clock rate in Hz
clk_set_rate: stubbed
clk_round_rate: stubbed
clk_set_parent: NULL
clk_get_parent: NULL
Signed-off-by: John Rigby <jrigby@freescale.com>
---
Makefile | 1 +
arch/powerpc/platforms/512x/Kconfig | 1 +
arch/powerpc/platforms/512x/Makefile | 1 +
arch/powerpc/platforms/512x/clock.c | 729 ++++++++++++++++++++++++++++++++++
4 files changed, 732 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/platforms/512x/clock.c
diff --git a/Makefile b/Makefile
index 6aff5f4..fc3ae9f 100644
--- a/Makefile
+++ b/Makefile
@@ -1,3 +1,4 @@
+FRED=42
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 26
diff --git a/arch/powerpc/platforms/512x/Kconfig b/arch/powerpc/platforms/512x/Kconfig
index 4c0da0c..162af06 100644
--- a/arch/powerpc/platforms/512x/Kconfig
+++ b/arch/powerpc/platforms/512x/Kconfig
@@ -2,6 +2,7 @@ config PPC_MPC512x
bool
select FSL_SOC
select IPIC
+ select PPC_CLOCK
default n
config PPC_MPC5121
diff --git a/arch/powerpc/platforms/512x/Makefile b/arch/powerpc/platforms/512x/Makefile
index 232c89f..90910c1 100644
--- a/arch/powerpc/platforms/512x/Makefile
+++ b/arch/powerpc/platforms/512x/Makefile
@@ -1,4 +1,5 @@
#
# Makefile for the Freescale PowerPC 512x linux kernel.
#
+obj-y += clock.o
obj-$(CONFIG_MPC5121_ADS) += mpc5121_ads.o
diff --git a/arch/powerpc/platforms/512x/clock.c b/arch/powerpc/platforms/512x/clock.c
new file mode 100644
index 0000000..f416014
--- /dev/null
+++ b/arch/powerpc/platforms/512x/clock.c
@@ -0,0 +1,729 @@
+/*
+ * Copyright (C) 2007,2008 Freescale Semiconductor, Inc. All rights reserved.
+ *
+ * Author: John Rigby <jrigby@freescale.com>
+ *
+ * Implements the clk api defined in include/linux/clk.h
+ *
+ * Original based on linux/arch/arm/mach-integrator/clock.c
+ *
+ * Copyright (C) 2004 ARM Limited.
+ * Written by Deep Blue Solutions Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/string.h>
+#include <linux/clk.h>
+#include <linux/mutex.h>
+#include <linux/io.h>
+
+#include <linux/of_platform.h>
+#include <asm/mpc512x.h>
+#include <asm/clk_interface.h>
+
+#undef CLK_DEBUG
+
+static int clocks_initialized;
+
+#define CLK_HAS_RATE 0x1 /* has rate in MHz */
+#define CLK_HAS_CTRL 0x2 /* has control reg and bit */
+
+struct clk {
+ struct list_head node;
+ char name[32];
+ int flags;
+ struct device *dev;
+ unsigned long rate;
+ struct module *owner;
+ void (*calc) (struct clk *);
+ struct clk *parent;
+ int reg, bit; /* CLK_HAS_CTRL */
+ int div_shift; /* only used by generic_div_clk_calc */
+};
+
+static LIST_HEAD(clocks);
+static DEFINE_MUTEX(clocks_mutex);
+
+static struct clk *mpc5121_clk_get(struct device *dev, const char *id)
+{
+ struct clk *p, *clk = ERR_PTR(-ENOENT);
+ int dev_match = 0;
+ int id_match = 0;
+
+ if (dev == NULL && id == NULL)
+ return NULL;
+
+ mutex_lock(&clocks_mutex);
+ list_for_each_entry(p, &clocks, node) {
+ if (dev && dev == p->dev)
+ dev_match++;
+ if (strcmp(id, p->name) == 0)
+ id_match++;
+ if ((dev_match || id_match) && try_module_get(p->owner)) {
+ clk = p;
+ break;
+ }
+ }
+ mutex_unlock(&clocks_mutex);
+
+ return clk;
+}
+
+#ifdef CLK_DEBUG
+static void dump_clocks(void)
+{
+ struct clk *p;
+
+ mutex_lock(&clocks_mutex);
+ printk(KERN_INFO "CLOCKS:\n");
+ list_for_each_entry(p, &clocks, node) {
+ printk(KERN_INFO " %s %ld", p->name, p->rate);
+ if (p->parent)
+ printk(KERN_INFO " %s %ld", p->parent->name,
+ p->parent->rate);
+ if (p->flags & CLK_HAS_CTRL)
+ printk(KERN_INFO " reg/bit %d/%d", p->reg, p->bit);
+ printk("\n");
+ }
+ mutex_unlock(&clocks_mutex);
+}
+#define DEBUG_CLK_DUMP() dump_clocks()
+#else
+#define DEBUG_CLK_DUMP()
+#endif
+
+
+static void mpc5121_clk_put(struct clk *clk)
+{
+ module_put(clk->owner);
+}
+
+#define NRPSC 12
+
+struct mpc512x_clockctl {
+ u32 spmr; /* System PLL Mode Reg */
+ u32 sccr[2]; /* System Clk Ctrl Reg 1 & 2 */
+ u32 scfr1; /* System Clk Freq Reg 1 */
+ u32 scfr2; /* System Clk Freq Reg 2 */
+ u32 reserved;
+ u32 bcr; /* Bread Crumb Reg */
+ u32 pccr[NRPSC]; /* PSC Clk Ctrl Reg 0-11 */
+ u32 spccr; /* SPDIF Clk Ctrl Reg */
+ u32 cccr; /* CFM Clk Ctrl Reg */
+ u32 dccr; /* DIU Clk Cnfg Reg */
+};
+
+struct mpc512x_clockctl __iomem *clockctl;
+
+static int mpc5121_clk_enable(struct clk *clk)
+{
+ unsigned int mask;
+
+ if (clk->flags & CLK_HAS_CTRL) {
+ mask = in_be32(&clockctl->sccr[clk->reg]);
+ mask |= 1 << clk->bit;
+ out_be32(&clockctl->sccr[clk->reg], mask);
+ }
+ return 0;
+}
+
+static void mpc5121_clk_disable(struct clk *clk)
+{
+ unsigned int mask;
+
+ if (clk->flags & CLK_HAS_CTRL) {
+ mask = in_be32(&clockctl->sccr[clk->reg]);
+ mask &= ~(1 << clk->bit);
+ out_be32(&clockctl->sccr[clk->reg], mask);
+ }
+}
+
+static unsigned long mpc5121_clk_get_rate(struct clk *clk)
+{
+ if (clk->flags & CLK_HAS_RATE)
+ return clk->rate;
+ else
+ return 0;
+}
+
+static long mpc5121_clk_round_rate(struct clk *clk, unsigned long rate)
+{
+ return rate;
+}
+
+static int mpc5121_clk_set_rate(struct clk *clk, unsigned long rate)
+{
+ return 0;
+}
+
+static int clk_register(struct clk *clk)
+{
+ mutex_lock(&clocks_mutex);
+ list_add(&clk->node, &clocks);
+ mutex_unlock(&clocks_mutex);
+ return 0;
+}
+
+static unsigned long spmf_mult(void)
+{
+ /*
+ * Convert spmf to multiplier
+ */
+ static int spmf_to_mult[] = {
+ 68, 1, 12, 16,
+ 20, 24, 28, 32,
+ 36, 40, 44, 48,
+ 52, 56, 60, 64
+ };
+ int spmf = (clockctl->spmr >> 24) & 0xf;
+ return spmf_to_mult[spmf];
+}
+
+static unsigned long sysdiv_div_x_2(void)
+{
+ /*
+ * Convert sysdiv to divisor x 2
+ * Some divisors have fractional parts so
+ * multiply by 2 then divide by this value
+ */
+ static int sysdiv_to_div_x_2[] = {
+ 4, 5, 6, 7,
+ 8, 9, 10, 14,
+ 12, 16, 18, 22,
+ 20, 24, 26, 30,
+ 28, 32, 34, 38,
+ 36, 40, 42, 46,
+ 44, 48, 50, 54,
+ 52, 56, 58, 62,
+ 60, 64, 66,
+ };
+ int sysdiv = (clockctl->scfr2 >> 26) & 0x3f;
+ return sysdiv_to_div_x_2[sysdiv];
+}
+
+static unsigned long ref_to_sys(unsigned long rate)
+{
+ rate *= spmf_mult();
+ rate *= 2;
+ rate /= sysdiv_div_x_2();
+
+ return rate;
+}
+
+static unsigned long sys_to_ref(unsigned long rate)
+{
+ rate *= sysdiv_div_x_2();
+ rate /= 2;
+ rate /= spmf_mult();
+
+ return rate;
+}
+
+static long ips_to_ref(unsigned long rate)
+{
+ int ips_div = (clockctl->scfr1 >> 23) & 0x7;
+
+ rate *= ips_div; /* csb_clk = ips_clk * ips_div */
+ rate *= 2; /* sys_clk = csb_clk * 2 */
+ return sys_to_ref(rate);
+}
+
+static unsigned long devtree_getfreq(char *clockname)
+{
+ struct device_node *np;
+ const unsigned int *prop;
+ unsigned int val = 0;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,mpc5121-immr");
+ if (np) {
+ prop = of_get_property(np, clockname, NULL);
+ if (prop)
+ val = *prop;
+ of_node_put(np);
+ }
+ return val;
+}
+
+static void ref_clk_calc(struct clk *clk)
+{
+ unsigned long rate;
+
+ rate = devtree_getfreq("bus-frequency");
+ if (rate == 0) {
+ printk(KERN_ERR "No bus-frequency in dev tree\n");
+ clk->rate = 0;
+ return;
+ }
+ clk->rate = ips_to_ref(rate);
+}
+
+static struct clk ref_clk = {
+ .name = "ref_clk",
+ .calc = ref_clk_calc,
+};
+
+
+static void sys_clk_calc(struct clk *clk)
+{
+ clk->rate = ref_to_sys(ref_clk.rate);
+}
+
+static struct clk sys_clk = {
+ .name = "sys_clk",
+ .calc = sys_clk_calc,
+};
+
+static void diu_clk_calc(struct clk *clk)
+{
+ int diudiv_x_2 = clockctl->scfr1 & 0xff;
+ unsigned long rate;
+
+ rate = sys_clk.rate;
+
+ rate *= 2;
+ rate /= diudiv_x_2;
+
+ clk->rate = rate;
+}
+
+static void half_clk_calc(struct clk *clk)
+{
+ clk->rate = clk->parent->rate / 2;
+}
+
+static void generic_div_clk_calc(struct clk *clk)
+{
+ int div = (clockctl->scfr1 >> clk->div_shift) & 0x7;
+
+ clk->rate = clk->parent->rate / div;
+}
+
+static void unity_clk_calc(struct clk *clk)
+{
+ clk->rate = clk->parent->rate;
+}
+
+static struct clk csb_clk = {
+ .name = "csb_clk",
+ .calc = half_clk_calc,
+ .parent = &sys_clk,
+};
+
+static void e300_clk_calc(struct clk *clk)
+{
+ int spmf = (clockctl->spmr >> 16) & 0xf;
+ int ratex2 = clk->parent->rate * spmf;
+
+ clk->rate = ratex2 / 2;
+}
+
+static struct clk e300_clk = {
+ .name = "e300_clk",
+ .calc = e300_clk_calc,
+ .parent = &csb_clk,
+};
+
+static struct clk ips_clk = {
+ .name = "ips_clk",
+ .calc = generic_div_clk_calc,
+ .parent = &csb_clk,
+ .div_shift = 23,
+};
+
+/*
+ * Clocks controlled by SCCR1 (.reg = 0)
+ */
+static struct clk lpc_clk = {
+ .name = "lpc_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 0,
+ .bit = 30,
+ .calc = generic_div_clk_calc,
+ .parent = &ips_clk,
+ .div_shift = 11,
+};
+
+static struct clk nfc_clk = {
+ .name = "nfc_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 0,
+ .bit = 29,
+ .calc = generic_div_clk_calc,
+ .parent = &ips_clk,
+ .div_shift = 8,
+};
+
+static struct clk pata_clk = {
+ .name = "pata_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 0,
+ .bit = 28,
+ .calc = unity_clk_calc,
+ .parent = &ips_clk,
+};
+
+/*
+ * PSC clocks (bits 27 - 16)
+ * are setup elsewhere
+ */
+
+static struct clk sata_clk = {
+ .name = "sata_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 0,
+ .bit = 14,
+ .calc = unity_clk_calc,
+ .parent = &ips_clk,
+};
+
+static struct clk fec_clk = {
+ .name = "fec_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 0,
+ .bit = 13,
+ .calc = unity_clk_calc,
+ .parent = &ips_clk,
+};
+
+static struct clk pci_clk = {
+ .name = "pci_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 0,
+ .bit = 11,
+ .calc = generic_div_clk_calc,
+ .parent = &csb_clk,
+ .div_shift = 20,
+};
+
+/*
+ * Clocks controlled by SCCR2 (.reg = 1)
+ */
+static struct clk diu_clk = {
+ .name = "diu_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 31,
+ .calc = diu_clk_calc,
+};
+
+static struct clk axe_clk = {
+ .name = "axe_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 30,
+ .calc = unity_clk_calc,
+ .parent = &csb_clk,
+};
+
+static struct clk usb1_clk = {
+ .name = "usb1_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 28,
+ .calc = unity_clk_calc,
+ .parent = &csb_clk,
+};
+
+static struct clk usb2_clk = {
+ .name = "usb2_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 27,
+ .calc = unity_clk_calc,
+ .parent = &csb_clk,
+};
+
+static struct clk i2c_clk = {
+ .name = "i2c_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 26,
+ .calc = unity_clk_calc,
+ .parent = &ips_clk,
+};
+
+static struct clk mscan_clk = {
+ .name = "mscan_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 25,
+ .calc = unity_clk_calc,
+ .parent = &ips_clk,
+};
+
+static struct clk sdhc_clk = {
+ .name = "sdhc_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 24,
+ .calc = unity_clk_calc,
+ .parent = &ips_clk,
+};
+
+static struct clk mbx_bus_clk = {
+ .name = "mbx_bus_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 22,
+ .calc = half_clk_calc,
+ .parent = &csb_clk,
+};
+
+static struct clk mbx_clk = {
+ .name = "mbx_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 21,
+ .calc = unity_clk_calc,
+ .parent = &csb_clk,
+};
+
+static struct clk mbx_3d_clk = {
+ .name = "mbx_3d_clk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 20,
+ .calc = generic_div_clk_calc,
+ .parent = &mbx_bus_clk,
+ .div_shift = 14,
+};
+
+static void psc_mclk_in_calc(struct clk *clk)
+{
+ clk->rate = devtree_getfreq("psc_mclk_in");
+ if (!clk->rate)
+ clk->rate = 25000000;
+}
+
+static struct clk psc_mclk_in = {
+ .name = "psc_mclk_in",
+ .calc = psc_mclk_in_calc,
+};
+
+static struct clk spdif_txclk = {
+ .name = "spdif_txclk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 23,
+};
+
+static struct clk spdif_rxclk = {
+ .name = "spdif_rxclk",
+ .flags = CLK_HAS_CTRL,
+ .reg = 1,
+ .bit = 23,
+};
+
+static void ac97_clk_calc(struct clk *clk)
+{
+ /* ac97 bit clock is always 24.567 MHz */
+ clk->rate = 24567000;
+}
+
+static struct clk ac97_clk = {
+ .name = "ac97_clk_in",
+ .calc = ac97_clk_calc,
+};
+
+struct clk *rate_clks[] = {
+ &ref_clk,
+ &sys_clk,
+ &diu_clk,
+ &csb_clk,
+ &e300_clk,
+ &ips_clk,
+ &fec_clk,
+ &sata_clk,
+ &pata_clk,
+ &nfc_clk,
+ &lpc_clk,
+ &mbx_bus_clk,
+ &mbx_clk,
+ &mbx_3d_clk,
+ &axe_clk,
+ &usb1_clk,
+ &usb2_clk,
+ &i2c_clk,
+ &mscan_clk,
+ &sdhc_clk,
+ &pci_clk,
+ &psc_mclk_in,
+ &spdif_txclk,
+ &spdif_rxclk,
+ &ac97_clk,
+ NULL
+};
+
+static void rate_clk_init(struct clk *clk)
+{
+ if (clk->calc) {
+ clk->calc(clk);
+ clk->flags |= CLK_HAS_RATE;
+ clk_register(clk);
+ } else {
+ printk(KERN_WARNING
+ "Could not initialize clk %s without a calc routine\n",
+ clk->name);
+ }
+}
+
+static void rate_clks_init(void)
+{
+ struct clk **cpp, *clk;
+
+ cpp = rate_clks;
+ while ((clk = *cpp++))
+ rate_clk_init(clk);
+}
+
+/*
+ * There are two clk enable registers with 32 enable bits each
+ * psc clocks and device clocks are all stored in dev_clks
+ */
+struct clk dev_clks[2][32];
+
+/*
+ * Given a psc number return the dev_clk
+ * associated with it
+ */
+static struct clk *psc_dev_clk(int pscnum)
+{
+ int reg, bit;
+ struct clk *clk;
+
+ reg = 0;
+ bit = 27 - pscnum;
+
+ clk = &dev_clks[reg][bit];
+ clk->reg = 0;
+ clk->bit = bit;
+ return clk;
+}
+
+/*
+ * PSC clock rate calculation
+ */
+static void psc_calc_rate(struct clk *clk, int pscnum, struct device_node *np)
+{
+ unsigned long mclk_src = sys_clk.rate;
+ unsigned long mclk_div;
+
+ /*
+ * Can only change value of mclk divider
+ * when the divider is disabled.
+ *
+ * Zero is not a valid divider so minimum
+ * divider is 1
+ *
+ * disable/set divider/enable
+ */
+ out_be32(&clockctl->pccr[pscnum], 0);
+ out_be32(&clockctl->pccr[pscnum], 0x00020000);
+ out_be32(&clockctl->pccr[pscnum], 0x00030000);
+
+ if (clockctl->pccr[pscnum] & 0x80) {
+ clk->rate = spdif_rxclk.rate;
+ return;
+ }
+
+ switch ((clockctl->pccr[pscnum] >> 14) & 0x3) {
+ case 0:
+ mclk_src = sys_clk.rate;
+ break;
+ case 1:
+ mclk_src = ref_clk.rate;
+ break;
+ case 2:
+ mclk_src = psc_mclk_in.rate;
+ break;
+ case 3:
+ mclk_src = spdif_txclk.rate;
+ break;
+ }
+
+ mclk_div = ((clockctl->pccr[pscnum] >> 17) & 0x7fff) + 1;
+ clk->rate = mclk_src / mclk_div;
+}
+
+/*
+ * Find all psc nodes in device tree and assign a clock
+ * with name "psc%d_mclk" and dev pointing at the device
+ * returned from of_find_device_by_node
+ */
+static void psc_clks_init(void)
+{
+ struct device_node *np;
+ const u32 *cell_index;
+ struct of_device *ofdev;
+
+ for_each_compatible_node(np, NULL, "fsl,mpc5121-psc") {
+ cell_index = of_get_property(np, "cell-index", NULL);
+ if (cell_index) {
+ int pscnum = *cell_index;
+ struct clk *clk = psc_dev_clk(pscnum);
+
+ clk->flags = CLK_HAS_RATE | CLK_HAS_CTRL;
+ ofdev = of_find_device_by_node(np);
+ clk->dev = &ofdev->dev;
+ /*
+ * AC97 is special rate clock does
+ * not go through normal path
+ */
+ if (strcmp("ac97", np->name) == 0)
+ clk->rate = ac97_clk.rate;
+ else
+ psc_calc_rate(clk, pscnum, np);
+ sprintf(clk->name, "psc%d_mclk", pscnum);
+ clk_register(clk);
+ clk_enable(clk);
+ }
+ }
+}
+
+static struct clk_interface mpc5121_clk_functions = {
+ .clk_get = mpc5121_clk_get,
+ .clk_enable = mpc5121_clk_enable,
+ .clk_disable = mpc5121_clk_disable,
+ .clk_get_rate = mpc5121_clk_get_rate,
+ .clk_put = mpc5121_clk_put,
+ .clk_round_rate = mpc5121_clk_round_rate,
+ .clk_set_rate = mpc5121_clk_set_rate,
+ .clk_set_parent = NULL,
+ .clk_get_parent = NULL,
+};
+
+static int
+mpc5121_clk_init(void)
+{
+ struct device_node *np;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,mpc5121-clock");
+ if (np) {
+ clockctl = of_iomap(np, 0);
+ of_node_put(np);
+ }
+
+ if (!clockctl) {
+ printk(KERN_ERR "Could not map clock control registers\n");
+ return 0;
+ }
+
+ rate_clks_init();
+ psc_clks_init();
+
+ /* leave clockctl mapped forever */
+ /*iounmap(clockctl); */
+ DEBUG_CLK_DUMP();
+ clocks_initialized++;
+ clk_functions = mpc5121_clk_functions;
+ return 0;
+}
+
+
+arch_initcall(mpc5121_clk_init);
--
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 3/4][Version 3] MPC5121 Add generic board support
2008-07-09 20:54 ` [PATCH 2/4][Version 3] MPC5121 clock driver John Rigby
@ 2008-07-09 20:54 ` John Rigby
2008-07-09 20:54 ` [PATCH 4/4][Version 3] MPC5121 Add MPC5121ADS cpld support John Rigby
0 siblings, 1 reply; 5+ messages in thread
From: John Rigby @ 2008-07-09 20:54 UTC (permalink / raw)
To: linuxppc-dev; +Cc: John Rigby
Move shared code from mpc5121_ads.c to new file mpc512x_shared.c
mpc512x_find_ips_freq -> unchanged
contents of mpc5121_ads_init_IRQ -> mpc512x_init_IRQ
looking for fsl,mpc5121-ipic instead of fsl,ipic
mpc5121_ads_declare_of_platform_devices -> mpc5121_declare_of_platform_devices
and use compatible for lookup instead of node name
Add new generic board setup mpc5121_generic.c
Signed-off-by: John Rigby <jrigby@freescale.com>
---
arch/powerpc/platforms/512x/Kconfig | 15 ++++-
arch/powerpc/platforms/512x/Makefile | 3 +-
arch/powerpc/platforms/512x/mpc5121_ads.c | 64 ++------------------
arch/powerpc/platforms/512x/mpc5121_generic.c | 58 ++++++++++++++++++
arch/powerpc/platforms/512x/mpc512x.h | 17 +++++
.../512x/{mpc5121_ads.c => mpc512x_shared.c} | 57 ++++++------------
6 files changed, 112 insertions(+), 102 deletions(-)
create mode 100644 arch/powerpc/platforms/512x/mpc5121_generic.c
create mode 100644 arch/powerpc/platforms/512x/mpc512x.h
copy arch/powerpc/platforms/512x/{mpc5121_ads.c => mpc512x_shared.c} (55%)
diff --git a/arch/powerpc/platforms/512x/Kconfig b/arch/powerpc/platforms/512x/Kconfig
index 162af06..5d72dc3 100644
--- a/arch/powerpc/platforms/512x/Kconfig
+++ b/arch/powerpc/platforms/512x/Kconfig
@@ -3,12 +3,10 @@ config PPC_MPC512x
select FSL_SOC
select IPIC
select PPC_CLOCK
- default n
config PPC_MPC5121
bool
select PPC_MPC512x
- default n
config MPC5121_ADS
bool "Freescale MPC5121E ADS"
@@ -17,4 +15,15 @@ config MPC5121_ADS
select PPC_MPC5121
help
This option enables support for the MPC5121E ADS board.
- default n
+
+config MPC5121_GENERIC
+ bool "Generic support for simple MPC5121 based boards"
+ depends on PPC_MULTIPLATFORM && PPC32
+ select DEFAULT_UIMAGE
+ select PPC_MPC5121
+ help
+ This option enables support for simple MPC5121 based boards
+ which do not need custom platform specific setup.
+
+ Compatible boards include: Protonic LVT base boards (ZANMCU
+ and VICVT2).
diff --git a/arch/powerpc/platforms/512x/Makefile b/arch/powerpc/platforms/512x/Makefile
index 90910c1..8090e22 100644
--- a/arch/powerpc/platforms/512x/Makefile
+++ b/arch/powerpc/platforms/512x/Makefile
@@ -1,5 +1,6 @@
#
# Makefile for the Freescale PowerPC 512x linux kernel.
#
-obj-y += clock.o
+obj-y += clock.o mpc512x_shared.o
obj-$(CONFIG_MPC5121_ADS) += mpc5121_ads.o
+obj-$(CONFIG_MPC5121_GENERIC) += mpc5121_generic.o
diff --git a/arch/powerpc/platforms/512x/mpc5121_ads.c b/arch/powerpc/platforms/512x/mpc5121_ads.c
index 50bd3a3..3ec9ca3 100644
--- a/arch/powerpc/platforms/512x/mpc5121_ads.c
+++ b/arch/powerpc/platforms/512x/mpc5121_ads.c
@@ -1,5 +1,5 @@
/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc. All rights reserved.
+ * Copyright (C) 2007, 2008 Freescale Semiconductor, Inc. All rights reserved.
*
* Author: John Rigby, <jrigby@freescale.com>, Thur Mar 29 2007
*
@@ -15,7 +15,6 @@
#include <linux/kernel.h>
#include <linux/io.h>
-#include <linux/irq.h>
#include <linux/of_platform.h>
#include <asm/machdep.h>
@@ -23,65 +22,11 @@
#include <asm/prom.h>
#include <asm/time.h>
-/**
- * mpc512x_find_ips_freq - Find the IPS bus frequency for a device
- * @node: device node
- *
- * Returns IPS bus frequency, or 0 if the bus frequency cannot be found.
- */
-unsigned long
-mpc512x_find_ips_freq(struct device_node *node)
-{
- struct device_node *np;
- const unsigned int *p_ips_freq = NULL;
-
- of_node_get(node);
- while (node) {
- p_ips_freq = of_get_property(node, "bus-frequency", NULL);
- if (p_ips_freq)
- break;
-
- np = of_get_parent(node);
- of_node_put(node);
- node = np;
- }
- if (node)
- of_node_put(node);
-
- return p_ips_freq ? *p_ips_freq : 0;
-}
-EXPORT_SYMBOL(mpc512x_find_ips_freq);
-
-static struct of_device_id __initdata of_bus_ids[] = {
- { .name = "soc", },
- { .name = "localbus", },
- {},
-};
-
-static void __init mpc5121_ads_declare_of_platform_devices(void)
-{
- /* Find every child of the SOC node and add it to of_platform */
- if (of_platform_bus_probe(NULL, of_bus_ids, NULL))
- printk(KERN_ERR __FILE__ ": "
- "Error while probing of_platform bus\n");
-}
+#include "mpc512x.h"
static void __init mpc5121_ads_init_IRQ(void)
{
- struct device_node *np;
-
- np = of_find_compatible_node(NULL, NULL, "fsl,ipic");
- if (!np)
- return;
-
- ipic_init(np, 0);
- of_node_put(np);
-
- /*
- * Initialize the default interrupt mapping priorities,
- * in case the boot rom changed something on us.
- */
- ipic_set_default_priority();
+ mpc512x_init_IRQ();
}
/*
@@ -97,7 +42,8 @@ static int __init mpc5121_ads_probe(void)
define_machine(mpc5121_ads) {
.name = "MPC5121 ADS",
.probe = mpc5121_ads_probe,
- .init = mpc5121_ads_declare_of_platform_devices,
+ .setup_arch = mpc5121_ads_setup_arch,
+ .init = mpc512x_declare_of_platform_devices,
.init_IRQ = mpc5121_ads_init_IRQ,
.get_irq = ipic_get_irq,
.calibrate_decr = generic_calibrate_decr,
diff --git a/arch/powerpc/platforms/512x/mpc5121_generic.c b/arch/powerpc/platforms/512x/mpc5121_generic.c
new file mode 100644
index 0000000..2479de9
--- /dev/null
+++ b/arch/powerpc/platforms/512x/mpc5121_generic.c
@@ -0,0 +1,58 @@
+/*
+ * Copyright (C) 2007,2008 Freescale Semiconductor, Inc. All rights reserved.
+ *
+ * Author: John Rigby, <jrigby@freescale.com>
+ *
+ * Description:
+ * MPC5121 SoC setup
+ *
+ * This is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/of_platform.h>
+
+#include <asm/machdep.h>
+#include <asm/ipic.h>
+#include <asm/prom.h>
+#include <asm/time.h>
+
+#include "mpc512x.h"
+
+/*
+ * list of supported boards
+ */
+static char *board[] __initdata = {
+ "prt,prtlvt",
+ NULL
+};
+
+/*
+ * Called very early, MMU is off, device-tree isn't unflattened
+ */
+static int __init mpc5121_generic_probe(void)
+{
+ unsigned long node = of_get_flat_dt_root();
+ int i = 0;
+
+ while (board[i]) {
+ if (of_flat_dt_is_compatible(node, board[i]))
+ break;
+ i++;
+ }
+
+ return board[i] != NULL;
+}
+
+define_machine(mpc5121_generic) {
+ .name = "MPC5121 generic",
+ .probe = mpc5121_generic_probe,
+ .init = mpc512x_declare_of_platform_devices,
+ .init_IRQ = mpc512x_init_IRQ,
+ .get_irq = ipic_get_irq,
+ .calibrate_decr = generic_calibrate_decr,
+};
diff --git a/arch/powerpc/platforms/512x/mpc512x.h b/arch/powerpc/platforms/512x/mpc512x.h
new file mode 100644
index 0000000..9c03693
--- /dev/null
+++ b/arch/powerpc/platforms/512x/mpc512x.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * Prototypes for MPC512x shared code
+ */
+
+#ifndef __MPC512X_H__
+#define __MPC512X_H__
+extern unsigned long mpc512x_find_ips_freq(struct device_node *node);
+extern void __init mpc512x_init_IRQ(void);
+void __init mpc512x_declare_of_platform_devices(void);
+#endif /* __MPC512X_H__ */
diff --git a/arch/powerpc/platforms/512x/mpc5121_ads.c b/arch/powerpc/platforms/512x/mpc512x_shared.c
similarity index 55%
copy from arch/powerpc/platforms/512x/mpc5121_ads.c
copy to arch/powerpc/platforms/512x/mpc512x_shared.c
index 50bd3a3..d8cd579 100644
--- a/arch/powerpc/platforms/512x/mpc5121_ads.c
+++ b/arch/powerpc/platforms/512x/mpc512x_shared.c
@@ -1,16 +1,15 @@
/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc. All rights reserved.
+ * Copyright (C) 2007,2008 Freescale Semiconductor, Inc. All rights reserved.
*
- * Author: John Rigby, <jrigby@freescale.com>, Thur Mar 29 2007
+ * Author: John Rigby <jrigby@freescale.com>
*
* Description:
- * MPC5121 ADS board setup
+ * MPC512x Shared code
*
* This is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
- *
*/
#include <linux/kernel.h>
@@ -23,12 +22,8 @@
#include <asm/prom.h>
#include <asm/time.h>
-/**
- * mpc512x_find_ips_freq - Find the IPS bus frequency for a device
- * @node: device node
- *
- * Returns IPS bus frequency, or 0 if the bus frequency cannot be found.
- */
+#include "mpc512x.h"
+
unsigned long
mpc512x_find_ips_freq(struct device_node *node)
{
@@ -52,25 +47,11 @@ mpc512x_find_ips_freq(struct device_node *node)
}
EXPORT_SYMBOL(mpc512x_find_ips_freq);
-static struct of_device_id __initdata of_bus_ids[] = {
- { .name = "soc", },
- { .name = "localbus", },
- {},
-};
-
-static void __init mpc5121_ads_declare_of_platform_devices(void)
-{
- /* Find every child of the SOC node and add it to of_platform */
- if (of_platform_bus_probe(NULL, of_bus_ids, NULL))
- printk(KERN_ERR __FILE__ ": "
- "Error while probing of_platform bus\n");
-}
-
-static void __init mpc5121_ads_init_IRQ(void)
+void __init mpc512x_init_IRQ(void)
{
struct device_node *np;
- np = of_find_compatible_node(NULL, NULL, "fsl,ipic");
+ np = of_find_compatible_node(NULL, NULL, "fsl,mpc5121-ipic");
if (!np)
return;
@@ -85,20 +66,18 @@ static void __init mpc5121_ads_init_IRQ(void)
}
/*
- * Called very early, MMU is off, device-tree isn't unflattened
+ * Nodes to do bus probe on, soc and localbus
*/
-static int __init mpc5121_ads_probe(void)
-{
- unsigned long root = of_get_flat_dt_root();
+static struct of_device_id __initdata of_bus_ids[] = {
+ { .compatible = "fsl,mpc5121-immr", },
+ { .compatible = "fsl,mpc5121-localbus", },
+ {},
+};
- return of_flat_dt_is_compatible(root, "fsl,mpc5121ads");
+void __init mpc512x_declare_of_platform_devices(void)
+{
+ if (of_platform_bus_probe(NULL, of_bus_ids, NULL))
+ printk(KERN_ERR __FILE__ ": "
+ "Error while probing of_platform bus\n");
}
-define_machine(mpc5121_ads) {
- .name = "MPC5121 ADS",
- .probe = mpc5121_ads_probe,
- .init = mpc5121_ads_declare_of_platform_devices,
- .init_IRQ = mpc5121_ads_init_IRQ,
- .get_irq = ipic_get_irq,
- .calibrate_decr = generic_calibrate_decr,
-};
--
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 4/4][Version 3] MPC5121 Add MPC5121ADS cpld support
2008-07-09 20:54 ` [PATCH 3/4][Version 3] MPC5121 Add generic board support John Rigby
@ 2008-07-09 20:54 ` John Rigby
0 siblings, 0 replies; 5+ messages in thread
From: John Rigby @ 2008-07-09 20:54 UTC (permalink / raw)
To: linuxppc-dev; +Cc: John Rigby
Add a interrupt host for the interrupt
controller in the mpc5121ads cpld.
PCI interrupts are 0-7 the rest are 8-15
Touchscreen pendown irq is hardwired to irq1
All other irqs are chained to irq0
Signed-off-by: John Rigby <jrigby@freescale.com>
---
arch/powerpc/platforms/512x/Kconfig | 1 +
arch/powerpc/platforms/512x/Makefile | 2 +-
arch/powerpc/platforms/512x/mpc5121_ads.c | 11 ++
arch/powerpc/platforms/512x/mpc5121_ads.h | 16 ++
arch/powerpc/platforms/512x/mpc5121_ads_cpld.c | 204 ++++++++++++++++++++++++
5 files changed, 233 insertions(+), 1 deletions(-)
create mode 100644 arch/powerpc/platforms/512x/mpc5121_ads.h
create mode 100644 arch/powerpc/platforms/512x/mpc5121_ads_cpld.c
diff --git a/arch/powerpc/platforms/512x/Kconfig b/arch/powerpc/platforms/512x/Kconfig
index 5d72dc3..c62f893 100644
--- a/arch/powerpc/platforms/512x/Kconfig
+++ b/arch/powerpc/platforms/512x/Kconfig
@@ -13,6 +13,7 @@ config MPC5121_ADS
depends on PPC_MULTIPLATFORM && PPC32
select DEFAULT_UIMAGE
select PPC_MPC5121
+ select MPC5121_ADS_CPLD
help
This option enables support for the MPC5121E ADS board.
diff --git a/arch/powerpc/platforms/512x/Makefile b/arch/powerpc/platforms/512x/Makefile
index 8090e22..90be2f5 100644
--- a/arch/powerpc/platforms/512x/Makefile
+++ b/arch/powerpc/platforms/512x/Makefile
@@ -2,5 +2,5 @@
# Makefile for the Freescale PowerPC 512x linux kernel.
#
obj-y += clock.o mpc512x_shared.o
-obj-$(CONFIG_MPC5121_ADS) += mpc5121_ads.o
+obj-$(CONFIG_MPC5121_ADS) += mpc5121_ads.o mpc5121_ads_cpld.o
obj-$(CONFIG_MPC5121_GENERIC) += mpc5121_generic.o
diff --git a/arch/powerpc/platforms/512x/mpc5121_ads.c b/arch/powerpc/platforms/512x/mpc5121_ads.c
index 3ec9ca3..5ebf693 100644
--- a/arch/powerpc/platforms/512x/mpc5121_ads.c
+++ b/arch/powerpc/platforms/512x/mpc5121_ads.c
@@ -23,10 +23,21 @@
#include <asm/time.h>
#include "mpc512x.h"
+#include "mpc5121_ads.h"
+
+static void __init mpc5121_ads_setup_arch(void)
+{
+ printk(KERN_INFO "MPC5121 ADS board from Freescale Semiconductor\n");
+ /*
+ * cpld regs are needed early
+ */
+ mpc5121_ads_cpld_map();
+}
static void __init mpc5121_ads_init_IRQ(void)
{
mpc512x_init_IRQ();
+ mpc5121_ads_cpld_pic_init();
}
/*
diff --git a/arch/powerpc/platforms/512x/mpc5121_ads.h b/arch/powerpc/platforms/512x/mpc5121_ads.h
new file mode 100644
index 0000000..662076c
--- /dev/null
+++ b/arch/powerpc/platforms/512x/mpc5121_ads.h
@@ -0,0 +1,16 @@
+/*
+ * Copyright (C) 2008 Freescale Semiconductor, Inc. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * Prototypes for ADS5121 specific code
+ */
+
+#ifndef __MPC512ADS_H__
+#define __MPC512ADS_H__
+extern void __init mpc5121_ads_cpld_map(void);
+extern void __init mpc5121_ads_cpld_pic_init(void);
+#endif /* __MPC512ADS_H__ */
diff --git a/arch/powerpc/platforms/512x/mpc5121_ads_cpld.c b/arch/powerpc/platforms/512x/mpc5121_ads_cpld.c
new file mode 100644
index 0000000..a6ce805
--- /dev/null
+++ b/arch/powerpc/platforms/512x/mpc5121_ads_cpld.c
@@ -0,0 +1,204 @@
+/*
+ * Copyright (C) 2008 Freescale Semiconductor, Inc. All rights reserved.
+ *
+ * Author: John Rigby, <jrigby@freescale.com>
+ *
+ * Description:
+ * MPC5121ADS CPLD irq handling
+ *
+ * This is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#undef DEBUG
+
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <asm/prom.h>
+
+static struct device_node *cpld_pic_node;
+static struct irq_host *cpld_pic_host;
+
+/*
+ * Bits to ignore in the misc_status register
+ * 0x10 touch screen pendown is hard routed to irq1
+ * 0x02 pci status is read from pci status register
+ */
+#define MISC_IGNORE 0x12
+
+/*
+ * Nothing to ignore in pci status register
+ */
+#define PCI_IGNORE 0x00
+
+struct cpld_pic {
+ u8 pci_mask;
+ u8 pci_status;
+ u8 route;
+ u8 misc_mask;
+ u8 misc_status;
+ u8 misc_control;
+};
+
+static struct cpld_pic __iomem *cpld_regs;
+
+static void __iomem *
+irq_to_pic_mask(unsigned int irq)
+{
+ return irq <= 7 ? &cpld_regs->pci_mask : &cpld_regs->misc_mask;
+}
+
+static unsigned int
+irq_to_pic_bit(unsigned int irq)
+{
+ return 1 << (irq & 0x7);
+}
+
+static void
+cpld_mask_irq(unsigned int irq)
+{
+ unsigned int cpld_irq = (unsigned int)irq_map[irq].hwirq;
+ void __iomem *pic_mask = irq_to_pic_mask(cpld_irq);
+
+ out_8(pic_mask,
+ in_8(pic_mask) | irq_to_pic_bit(cpld_irq));
+}
+
+static void
+cpld_unmask_irq(unsigned int irq)
+{
+ unsigned int cpld_irq = (unsigned int)irq_map[irq].hwirq;
+ void __iomem *pic_mask = irq_to_pic_mask(cpld_irq);
+
+ out_8(pic_mask,
+ in_8(pic_mask) & ~irq_to_pic_bit(cpld_irq));
+}
+
+static struct irq_chip cpld_pic = {
+ .typename = " CPLD PIC ",
+ .mask = cpld_mask_irq,
+ .ack = cpld_mask_irq,
+ .unmask = cpld_unmask_irq,
+};
+
+static int
+cpld_pic_get_irq(int offset, u8 ignore, u8 __iomem *statusp,
+ u8 __iomem *maskp)
+{
+ int cpld_irq;
+ u8 status = in_8(statusp);
+ u8 mask = in_8(maskp);
+
+ /* ignore don't cares and masked irqs */
+ status |= (ignore | mask);
+
+ if (status == 0xff)
+ return NO_IRQ_IGNORE;
+
+ cpld_irq = ffz(status) + offset;
+
+ return irq_linear_revmap(cpld_pic_host, cpld_irq);
+}
+
+static void
+cpld_pic_cascade(unsigned int irq, struct irq_desc *desc)
+{
+ irq = cpld_pic_get_irq(0, PCI_IGNORE, &cpld_regs->pci_status,
+ &cpld_regs->pci_mask);
+ if (irq != NO_IRQ && irq != NO_IRQ_IGNORE) {
+ generic_handle_irq(irq);
+ return;
+ }
+
+ irq = cpld_pic_get_irq(8, MISC_IGNORE, &cpld_regs->misc_status,
+ &cpld_regs->misc_mask);
+ if (irq != NO_IRQ && irq != NO_IRQ_IGNORE) {
+ generic_handle_irq(irq);
+ return;
+ }
+}
+
+static int
+cpld_pic_host_match(struct irq_host *h, struct device_node *node)
+{
+ return cpld_pic_node == node;
+}
+
+static int
+cpld_pic_host_map(struct irq_host *h, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ get_irq_desc(virq)->status |= IRQ_LEVEL;
+ set_irq_chip_and_handler(virq, &cpld_pic, handle_level_irq);
+ return 0;
+}
+
+static struct
+irq_host_ops cpld_pic_host_ops = {
+ .match = cpld_pic_host_match,
+ .map = cpld_pic_host_map,
+};
+
+void __init
+mpc5121_ads_cpld_map(void)
+{
+ struct device_node *np = NULL;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,mpc5121ads-cpld-pic");
+ if (!np) {
+ printk(KERN_ERR "CPLD PIC init: can not find cpld-pic node\n");
+ return;
+ }
+
+ cpld_regs = of_iomap(np, 0);
+ of_node_put(np);
+}
+
+void __init
+mpc5121_ads_cpld_pic_init(void)
+{
+ unsigned int cascade_irq;
+ struct device_node *np = NULL;
+
+ pr_debug("cpld_ic_init\n");
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,mpc5121ads-cpld-pic");
+ if (!np) {
+ printk(KERN_ERR "CPLD PIC init: can not find cpld-pic node\n");
+ return;
+ }
+
+ if (!cpld_regs)
+ goto end;
+
+ cascade_irq = irq_of_parse_and_map(np, 0);
+ if (cascade_irq == NO_IRQ)
+ goto end;
+
+ /*
+ * statically route touch screen pendown through 1
+ * and ignore it here
+ * route all others through our cascade irq
+ */
+ out_8(&cpld_regs->route, 0xfd);
+ out_8(&cpld_regs->pci_mask, 0xff);
+ /* unmask pci ints in misc mask */
+ out_8(&cpld_regs->misc_mask, ~(MISC_IGNORE));
+
+ cpld_pic_node = of_node_get(np);
+
+ cpld_pic_host =
+ irq_alloc_host(np, IRQ_HOST_MAP_LINEAR, 16, &cpld_pic_host_ops, 16);
+ if (!cpld_pic_host) {
+ printk(KERN_ERR "CPLD PIC: failed to allocate irq host!\n");
+ goto end;
+ }
+
+ set_irq_chained_handler(cascade_irq, cpld_pic_cascade);
+end:
+ of_node_put(np);
+}
--
^ permalink raw reply related [flat|nested] 5+ messages in thread
end of thread, other threads:[~2008-07-09 20:54 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-07-09 20:54 [PATCH 0/4][Version 3] MPC5121 Updates John Rigby
2008-07-09 20:54 ` [PATCH 1/4][Version 3] MPC5121 Update MPC5121ADS device tree John Rigby
2008-07-09 20:54 ` [PATCH 2/4][Version 3] MPC5121 clock driver John Rigby
2008-07-09 20:54 ` [PATCH 3/4][Version 3] MPC5121 Add generic board support John Rigby
2008-07-09 20:54 ` [PATCH 4/4][Version 3] MPC5121 Add MPC5121ADS cpld support John Rigby
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).