From: Mirek23 <miroslaw.dach@psi.ch>
To: linuxppc-embedded@ozlabs.org
Subject: Linux doesn not boot from u-boot on ML403
Date: Mon, 27 Aug 2007 06:35:37 -0700 (PDT) [thread overview]
Message-ID: <12347049.post@talk.nabble.com> (raw)
Hi All,
I run Linux 2.6.21 (by Grant) on my Avnet Virtex-4 evaluation board
(ML403 like). When I load zIinux.elf
via jtag to the board it runs properly:
loaded at: 00400000 004F9138
board data at: 004F7120 004F7138
relocated to: 004040B4 004040CC
zimage at: 00404E59 004F6EE6
avail ram: 004FA000 01FFFFFF
Linux/PPC load: console=ttyUL0,9600 root=/dev/nfs rw
nfsroot=129.117.144.113:/opt/eldk41/ppc_4xx,tcp
ip=::::virtex4-mirek:eth0:dhcp panic=1
Uncompressing Linux...done.
Now booting the kernel
[0.000000] Linux version 2.6.21-rc6 (root@pc5215) (gcc version 4.0.2) #11
Tue Aug 7 13:46:19 EST 2007
[0.000000] Xilinx ML403 Reference System (Virtex-4 FX)
.
.
.
.
It goes to the successful end.
I have build u-boot 1.2.0 with uart lite and temac support.
When I am trying to run uImage (build out of zImage) it does not run.
The steps I do are as following:
1. I build uImage withing the kernel tree (make uImage)
2. I load via jtag the u-boot 1.2.0
XMD% dow u-boot.elf
section, .text: 0x00800000-0x0081513c
section, .resetvec: 0x0081513c-0x00815140
section, .rodata: 0x00815140-0x00817ce0
section, .reloc: 0x00817d00-0x00818674
section, .data: 0x00818674-0x00818b08
section, .data.rel: 0x00818b08-0x00818b34
section, .data.rel.local: 0x00818b34-0x00818f6c
section, .u_boot_cmd: 0x00818f6c-0x008191dc
section, .bss: 0x00819200-0x0081dd04
3. I transfer uImage to the RAM memory of my Avnet board:
TFTP from server 129.129.144.113; our IP address is 129.129.144.157
Filename 'uImage'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
################################################################
done
Bytes transferred = 991438 (f20ce hex)
4. I am trying to start the kernel
=> bootm 0x1000000
## Booting image at 01000000 ...
Image Name: Linux-2.6.21-rc6
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 991375 Bytes = 968.1 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
After all system hangs
I have tried to change the Load Address and Entry Point to 0x400000 (mkimage
-a 0x400000 -e 0x400000)
but the system hangs like in the first case.
my bootargs are:
console=ttyUL0,9600 root=/dev/nfs rw
nfsroot=129.117.144.113:/opt/eldk41/ppc_4xx,tcp
ip=::::virtex4-mirek:eth0:dhcp panic=1
Those bootargs where tested with zImage.elf and seem to be fine.
Does somebody has some suggestion?
Thank you in advance for any hint on that.
Mirek
--
View this message in context: http://www.nabble.com/Linux-doesn-not-boot-from-u-boot-on-ML403-tf4335322.html#a12347049
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
next reply other threads:[~2007-08-27 13:35 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-08-27 13:35 Mirek23 [this message]
2007-08-27 14:24 ` Linux doesn not boot from u-boot on ML403 Grant Likely
2007-08-27 14:36 ` Miroslaw Dach
2007-08-27 14:53 ` Grant Likely
2007-08-28 11:18 ` Miroslaw Dach
2007-08-28 13:02 ` Grant Likely
2007-08-28 13:37 ` Miroslaw Dach
2007-08-28 13:50 ` Grant Likely
2007-08-28 15:00 ` Miroslaw Dach
2007-08-28 15:10 ` Grant Likely
2007-08-28 15:22 ` Miroslaw Dach
2007-08-28 15:28 ` Grant Likely
2007-08-29 8:41 ` Miroslaw Dach
2007-08-29 15:17 ` Grant Likely
2007-08-29 15:31 ` Miroslaw Dach
2007-08-30 7:50 ` Miroslaw Dach
2007-08-30 13:21 ` Grant Likely
2007-08-29 15:32 ` Miroslaw Dach
-- strict thread matches above, loose matches on Subject: below --
2007-09-23 13:27 Miroslaw Dach
2007-09-23 15:32 ` Grant Likely
2007-09-23 19:44 ` Josh Boyer
2007-09-25 8:25 ` Mirek23
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=12347049.post@talk.nabble.com \
--to=miroslaw.dach@psi.ch \
--cc=linuxppc-embedded@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).