* [PATCH 0/4] sbc834x update; PCI IRQ fix, enable MTD, USB @ 2009-08-12 13:34 Paul Gortmaker 2009-08-12 13:34 ` [PATCH 1/4] Remove second USB node from SBC834x DTS Paul Gortmaker 0 siblings, 1 reply; 9+ messages in thread From: Paul Gortmaker @ 2009-08-12 13:34 UTC (permalink / raw) To: linuxppc-dev This is a handful of small sbc834x patches, entirely limited in scope to this board's DTS/defconfig. Aside from the PCI IRQ mis-assignment fix, the other changes are aimed at improving the general functionality of the board out of the box, by enabling MTD and USB storage. Paul. ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 1/4] Remove second USB node from SBC834x DTS 2009-08-12 13:34 [PATCH 0/4] sbc834x update; PCI IRQ fix, enable MTD, USB Paul Gortmaker @ 2009-08-12 13:34 ` Paul Gortmaker 2009-08-12 13:34 ` [PATCH 2/4] Add localbus node and MTD partitions for SBC834x Paul Gortmaker 2009-08-14 20:21 ` [PATCH 1/4] Remove second USB node from SBC834x DTS Kumar Gala 0 siblings, 2 replies; 9+ messages in thread From: Paul Gortmaker @ 2009-08-12 13:34 UTC (permalink / raw) To: linuxppc-dev From: Liang Li <liang.li@windriver.com> Since only one of the SoC USB devices is brought out to a physical connector on the board, remove the 2nd (USB-DR) node from the DTS. Having it present and USB enabled will cause a hang at boot. Signed-off-by: Liang Li <liang.li@windriver.com> Signed-off-by: Yang Shi <yang.shi@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> --- arch/powerpc/boot/dts/sbc8349.dts | 12 ------------ 1 files changed, 0 insertions(+), 12 deletions(-) diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts index 2d9fa68..d93e5be 100644 --- a/arch/powerpc/boot/dts/sbc8349.dts +++ b/arch/powerpc/boot/dts/sbc8349.dts @@ -146,18 +146,6 @@ phy_type = "ulpi"; port0; }; - /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */ - usb@23000 { - device_type = "usb"; - compatible = "fsl-usb2-dr"; - reg = <0x23000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&ipic>; - interrupts = <38 0x8>; - dr_mode = "otg"; - phy_type = "ulpi"; - }; enet0: ethernet@24000 { #address-cells = <1>; -- 1.6.3.3 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/4] Add localbus node and MTD partitions for SBC834x 2009-08-12 13:34 ` [PATCH 1/4] Remove second USB node from SBC834x DTS Paul Gortmaker @ 2009-08-12 13:34 ` Paul Gortmaker 2009-08-12 13:34 ` [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS Paul Gortmaker 2009-08-14 20:32 ` [PATCH 2/4] Add localbus node and MTD partitions for SBC834x Kumar Gala 2009-08-14 20:21 ` [PATCH 1/4] Remove second USB node from SBC834x DTS Kumar Gala 1 sibling, 2 replies; 9+ messages in thread From: Paul Gortmaker @ 2009-08-12 13:34 UTC (permalink / raw) To: linuxppc-dev From: Liang Li <liang.li@windriver.com> There is 8MB flash, 8kB EEPROM and 128MB SDRAM on the sbc834x local bus, so add a localbus node in DTS with MTD partitions. The recent U-boot commit fe613cdd4eb moves u-boot to the beginning of flash, hence the legacy label on the partition at the end of flash. Signed-off-by: Liang Li <liang.li@windriver.com> Signed-off-by: Yang Shi <yang.shi@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> --- arch/powerpc/boot/dts/sbc8349.dts | 40 +++++++++++++++++++++++++++++++++++++ 1 files changed, 40 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts index d93e5be..b83036a 100644 --- a/arch/powerpc/boot/dts/sbc8349.dts +++ b/arch/powerpc/boot/dts/sbc8349.dts @@ -265,6 +265,46 @@ }; }; + localbus@e0005000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8349-localbus", "simple-bus"; + reg = <0xe0005000 0x1000>; + interrupts = <77 0x8>; + interrupt-parent = <&ipic>; + ranges = <0x0 0x0 0xff800000 0x00800000 /* 8MB Flash */ + 0x1 0x0 0xf8000000 0x00002000 /* 8KB EEPROM */ + 0x2 0x0 0x10000000 0x04000000 /* 64MB SDRAM */ + 0x3 0x0 0x10000000 0x04000000>; /* 64MB SDRAM */ + + flash@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "intel,28F640J3A", "cfi-flash"; + reg = <0x0 0x0 0x800000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition@40000 { + label = "user"; + reg = <0x00040000 0x006c0000>; + }; + + partition@700000 { + label = "legacy u-boot"; + reg = <0x00700000 0x00100000>; + read-only; + }; + + }; + }; + pci0: pci@e0008500 { interrupt-map-mask = <0xf800 0x0 0x0 0x7>; interrupt-map = < -- 1.6.3.3 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS 2009-08-12 13:34 ` [PATCH 2/4] Add localbus node and MTD partitions for SBC834x Paul Gortmaker @ 2009-08-12 13:34 ` Paul Gortmaker 2009-08-12 13:34 ` [PATCH 4/4] sbc8349: update defconfig, enable MTD, USB storage Paul Gortmaker 2009-08-14 20:21 ` [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS Kumar Gala 2009-08-14 20:32 ` [PATCH 2/4] Add localbus node and MTD partitions for SBC834x Kumar Gala 1 sibling, 2 replies; 9+ messages in thread From: Paul Gortmaker @ 2009-08-12 13:34 UTC (permalink / raw) To: linuxppc-dev From: Liang Li <liang.li@windriver.com> Allows interrupts to occur on the sbc834x. Currently PCI devices get assigned an incorrect IRQ and so the interrupt count never increases. This was tested with the 82546GB based dual port E1000 PCI-X NIC which uses two distinct IRQ lines on the one card. root@localhost:/root> cat /proc/interrupts | grep eth 17: 78 IPIC Level eth1 48: 27121 IPIC Level eth0 Signed-off-by: Liang Li <liang.li@windriver.com> Signed-off-by: Yang Shi <yang.shi@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> --- arch/powerpc/boot/dts/sbc8349.dts | 8 ++++---- 1 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts index b83036a..0dc90f9 100644 --- a/arch/powerpc/boot/dts/sbc8349.dts +++ b/arch/powerpc/boot/dts/sbc8349.dts @@ -310,10 +310,10 @@ interrupt-map = < /* IDSEL 0x11 */ - 0x8800 0x0 0x0 0x1 &ipic 20 0x8 - 0x8800 0x0 0x0 0x2 &ipic 21 0x8 - 0x8800 0x0 0x0 0x3 &ipic 22 0x8 - 0x8800 0x0 0x0 0x4 &ipic 23 0x8>; + 0x8800 0x0 0x0 0x1 &ipic 48 0x8 + 0x8800 0x0 0x0 0x2 &ipic 17 0x8 + 0x8800 0x0 0x0 0x3 &ipic 18 0x8 + 0x8800 0x0 0x0 0x4 &ipic 19 0x8>; interrupt-parent = <&ipic>; interrupts = <0x42 0x8>; -- 1.6.3.3 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 4/4] sbc8349: update defconfig, enable MTD, USB storage 2009-08-12 13:34 ` [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS Paul Gortmaker @ 2009-08-12 13:34 ` Paul Gortmaker 2009-08-14 20:21 ` Kumar Gala 2009-08-14 20:21 ` [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS Kumar Gala 1 sibling, 1 reply; 9+ messages in thread From: Paul Gortmaker @ 2009-08-12 13:34 UTC (permalink / raw) To: linuxppc-dev With flash partition entries in the DTS file, MTD might as well be enabled in the defconfig. In a similar vein, enable USB and enough related options (SCSI/ext2/ext3) so that a user can read and write to a generic USB flash drive as well. Also, this board only has the two default SOC UARTs, so adjust the UART config accordingly. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> --- arch/powerpc/configs/83xx/sbc834x_defconfig | 320 ++++++++++++++++++++++++++- 1 files changed, 308 insertions(+), 12 deletions(-) diff --git a/arch/powerpc/configs/83xx/sbc834x_defconfig b/arch/powerpc/configs/83xx/sbc834x_defconfig index a592b5e..3a68f86 100644 --- a/arch/powerpc/configs/83xx/sbc834x_defconfig +++ b/arch/powerpc/configs/83xx/sbc834x_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.31-rc4 -# Wed Jul 29 23:32:13 2009 +# Linux kernel version: 2.6.31-rc5 +# Tue Aug 11 19:57:51 2009 # # CONFIG_PPC64 is not set @@ -420,7 +420,90 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set -# CONFIG_MTD is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_CONCAT=y +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_TESTS is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_OF_PARTS=y +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +CONFIG_MTD_CFI_INTELEXT=y +# CONFIG_MTD_CFI_AMDSTD is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_INTEL_VR_NOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# LPDDR flash memory drivers +# +# CONFIG_MTD_LPDDR is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y CONFIG_OF_MDIO=y @@ -436,6 +519,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=32768 @@ -468,9 +552,38 @@ CONFIG_HAVE_IDE=y # SCSI device support # # CONFIG_RAID_ATTRS is not set -# CONFIG_SCSI is not set -# CONFIG_SCSI_DMA is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set # CONFIG_SCSI_NETLINK is not set +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set # CONFIG_ATA is not set # CONFIG_MD is not set # CONFIG_FUSION is not set @@ -578,11 +691,21 @@ CONFIG_GIANFAR=y # # Enable WiMAX (Networking options) to see the WiMAX drivers # + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set +# CONFIG_NET_FC is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set @@ -633,9 +756,9 @@ CONFIG_DEVKMEM=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_PCI=y -CONFIG_SERIAL_8250_NR_UARTS=4 -CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +# CONFIG_SERIAL_8250_PCI is not set +CONFIG_SERIAL_8250_NR_UARTS=2 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 # CONFIG_SERIAL_8250_EXTENDED is not set # @@ -700,6 +823,7 @@ CONFIG_I2C_MPC=y # # CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set # # Graphics adapter I2C/DDC channel drivers @@ -814,6 +938,11 @@ CONFIG_WATCHDOG=y # # CONFIG_PCIPCWATCHDOG is not set # CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set CONFIG_SSB_POSSIBLE=y # @@ -856,12 +985,134 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set # CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set # CONFIG_HID_PID is not set # +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set + +# # Special HID drivers # -# CONFIG_USB_SUPPORT is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_ROOT_HUB_TT=y +# CONFIG_USB_EHCI_TT_NEWSCHED is not set +CONFIG_USB_EHCI_FSL=y +CONFIG_USB_EHCI_HCD_PPC_OF=y +# CONFIG_USB_OXU210HP_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_OHCI_HCD is not set +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_WHCI_HCD is not set +# CONFIG_USB_HWA_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set + +# +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may +# + +# +# also be needed; see USB_STORAGE Help for more info +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_SEVSEG is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set +# CONFIG_USB_GADGET is not set + +# +# OTG and related infrastructure +# +# CONFIG_NOP_USB_XCEIV is not set # CONFIG_UWB is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -882,9 +1133,14 @@ CONFIG_HID=y # # File systems # -# CONFIG_EXT2_FS is not set -# CONFIG_EXT3_FS is not set +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +# CONFIG_EXT3_FS_XATTR is not set # CONFIG_EXT4_FS is not set +CONFIG_JBD=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set @@ -940,6 +1196,7 @@ CONFIG_MISC_FILESYSTEMS=y # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set +# CONFIG_JFFS2_FS is not set # CONFIG_CRAMFS is not set # CONFIG_SQUASHFS is not set # CONFIG_VXFS_FS is not set @@ -977,7 +1234,46 @@ CONFIG_RPCSEC_GSS_KRB5=y # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y -# CONFIG_NLS is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set # CONFIG_BINARY_PRINTF is not set -- 1.6.3.3 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH 4/4] sbc8349: update defconfig, enable MTD, USB storage 2009-08-12 13:34 ` [PATCH 4/4] sbc8349: update defconfig, enable MTD, USB storage Paul Gortmaker @ 2009-08-14 20:21 ` Kumar Gala 0 siblings, 0 replies; 9+ messages in thread From: Kumar Gala @ 2009-08-14 20:21 UTC (permalink / raw) To: Paul Gortmaker; +Cc: linuxppc-dev On Aug 12, 2009, at 8:34 AM, Paul Gortmaker wrote: > With flash partition entries in the DTS file, MTD might as well > be enabled in the defconfig. In a similar vein, enable USB and > enough related options (SCSI/ext2/ext3) so that a user can read > and write to a generic USB flash drive as well. > > Also, this board only has the two default SOC UARTs, so adjust the > UART config accordingly. > > Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> > --- > arch/powerpc/configs/83xx/sbc834x_defconfig | 320 ++++++++++++++++++ > ++++++++- > 1 files changed, 308 insertions(+), 12 deletions(-) applied to next - k ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS 2009-08-12 13:34 ` [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS Paul Gortmaker 2009-08-12 13:34 ` [PATCH 4/4] sbc8349: update defconfig, enable MTD, USB storage Paul Gortmaker @ 2009-08-14 20:21 ` Kumar Gala 1 sibling, 0 replies; 9+ messages in thread From: Kumar Gala @ 2009-08-14 20:21 UTC (permalink / raw) To: Paul Gortmaker; +Cc: linuxppc-dev On Aug 12, 2009, at 8:34 AM, Paul Gortmaker wrote: > From: Liang Li <liang.li@windriver.com> > > Allows interrupts to occur on the sbc834x. Currently PCI devices > get assigned an incorrect IRQ and so the interrupt count never > increases. This was tested with the 82546GB based dual port E1000 > PCI-X NIC which uses two distinct IRQ lines on the one card. > > root@localhost:/root> cat /proc/interrupts | grep eth > 17: 78 IPIC Level eth1 > 48: 27121 IPIC Level eth0 > > Signed-off-by: Liang Li <liang.li@windriver.com> > Signed-off-by: Yang Shi <yang.shi@windriver.com> > Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> > --- > arch/powerpc/boot/dts/sbc8349.dts | 8 ++++---- > 1 files changed, 4 insertions(+), 4 deletions(-) applied to next - k ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 2/4] Add localbus node and MTD partitions for SBC834x 2009-08-12 13:34 ` [PATCH 2/4] Add localbus node and MTD partitions for SBC834x Paul Gortmaker 2009-08-12 13:34 ` [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS Paul Gortmaker @ 2009-08-14 20:32 ` Kumar Gala 1 sibling, 0 replies; 9+ messages in thread From: Kumar Gala @ 2009-08-14 20:32 UTC (permalink / raw) To: Paul Gortmaker; +Cc: linuxppc-dev On Aug 12, 2009, at 8:34 AM, Paul Gortmaker wrote: > From: Liang Li <liang.li@windriver.com> > > There is 8MB flash, 8kB EEPROM and 128MB SDRAM on the sbc834x > local bus, so add a localbus node in DTS with MTD partitions. > > The recent U-boot commit fe613cdd4eb moves u-boot to the beginning > of flash, hence the legacy label on the partition at the end of flash. > > Signed-off-by: Liang Li <liang.li@windriver.com> > Signed-off-by: Yang Shi <yang.shi@windriver.com> > Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> > --- > arch/powerpc/boot/dts/sbc8349.dts | 40 ++++++++++++++++++++++++++++ > +++++++++ > 1 files changed, 40 insertions(+), 0 deletions(-) applied to next - k ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 1/4] Remove second USB node from SBC834x DTS 2009-08-12 13:34 ` [PATCH 1/4] Remove second USB node from SBC834x DTS Paul Gortmaker 2009-08-12 13:34 ` [PATCH 2/4] Add localbus node and MTD partitions for SBC834x Paul Gortmaker @ 2009-08-14 20:21 ` Kumar Gala 1 sibling, 0 replies; 9+ messages in thread From: Kumar Gala @ 2009-08-14 20:21 UTC (permalink / raw) To: Paul Gortmaker; +Cc: linuxppc-dev On Aug 12, 2009, at 8:34 AM, Paul Gortmaker wrote: > From: Liang Li <liang.li@windriver.com> > > Since only one of the SoC USB devices is brought out to a physical > connector on the board, remove the 2nd (USB-DR) node from the DTS. > Having it present and USB enabled will cause a hang at boot. > > Signed-off-by: Liang Li <liang.li@windriver.com> > Signed-off-by: Yang Shi <yang.shi@windriver.com> > Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> > --- > arch/powerpc/boot/dts/sbc8349.dts | 12 ------------ > 1 files changed, 0 insertions(+), 12 deletions(-) applied to next - k ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2009-08-14 20:32 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2009-08-12 13:34 [PATCH 0/4] sbc834x update; PCI IRQ fix, enable MTD, USB Paul Gortmaker 2009-08-12 13:34 ` [PATCH 1/4] Remove second USB node from SBC834x DTS Paul Gortmaker 2009-08-12 13:34 ` [PATCH 2/4] Add localbus node and MTD partitions for SBC834x Paul Gortmaker 2009-08-12 13:34 ` [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS Paul Gortmaker 2009-08-12 13:34 ` [PATCH 4/4] sbc8349: update defconfig, enable MTD, USB storage Paul Gortmaker 2009-08-14 20:21 ` Kumar Gala 2009-08-14 20:21 ` [PATCH 3/4] Fix incorrect PCI interrupt map in SBC834x DTS Kumar Gala 2009-08-14 20:32 ` [PATCH 2/4] Add localbus node and MTD partitions for SBC834x Kumar Gala 2009-08-14 20:21 ` [PATCH 1/4] Remove second USB node from SBC834x DTS Kumar Gala
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).