* [HELP] BAD interrupts @ 2009-12-23 14:11 Kumar Gopalpet-B05799 2009-12-23 22:43 ` Michael Ellerman 0 siblings, 1 reply; 5+ messages in thread From: Kumar Gopalpet-B05799 @ 2009-12-23 14:11 UTC (permalink / raw) To: netdev, linuxppc-dev [-- Attachment #1: Type: text/plain, Size: 401 bytes --] Hi all, I am trying linux 2.6.32-rc3 in SMP mode. I am seeing a lot of BAD interrupts when I do a "cat /proc/interrupts". I am running a forwarding application b/w two ethernet ports (ethernet uses gianfar driver). Has any one observed these BAD interrupts ? If so, can someone help me in understanding why these interrupts come and how to resolve it ? -- Thanks Sandeep [-- Attachment #2: Type: text/html, Size: 1737 bytes --] ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [HELP] BAD interrupts 2009-12-23 14:11 [HELP] BAD interrupts Kumar Gopalpet-B05799 @ 2009-12-23 22:43 ` Michael Ellerman 2009-12-24 11:46 ` gshan 0 siblings, 1 reply; 5+ messages in thread From: Michael Ellerman @ 2009-12-23 22:43 UTC (permalink / raw) To: Kumar Gopalpet-B05799; +Cc: netdev, linuxppc-dev [-- Attachment #1: Type: text/plain, Size: 922 bytes --] On Wed, 2009-12-23 at 19:41 +0530, Kumar Gopalpet-B05799 wrote: > Hi all, > > I am trying linux 2.6.32-rc3 in SMP mode. I am seeing a lot of BAD > interrupts when I do a "cat /proc/interrupts". > > I am running a forwarding application b/w two ethernet ports (ethernet > uses gianfar driver). > > Has any one observed these BAD interrupts ? If so, can someone help me > in understanding why these interrupts come and how to resolve it ? You'll need to tell us what platform you're running on. The BAD interrupts come from ppc_spurious_interrupts. It's a count of the number of times we entered do_IRQ() (ie. took an external interrupt), but when we asked the interrupt controller which irq it was, the interrupt controller said there was no irq. Depending on your interrupt controller that might happen sometimes for valid reasons. Or it might indicate something is setup wrong. cheers [-- Attachment #2: This is a digitally signed message part --] [-- Type: application/pgp-signature, Size: 197 bytes --] ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [HELP] BAD interrupts 2009-12-23 22:43 ` Michael Ellerman @ 2009-12-24 11:46 ` gshan 2009-12-24 10:45 ` Kumar Gopalpet-B05799 0 siblings, 1 reply; 5+ messages in thread From: gshan @ 2009-12-24 11:46 UTC (permalink / raw) To: michael; +Cc: netdev, linuxppc-dev, Kumar Gopalpet-B05799 Michael Ellerman wrote: > On Wed, 2009-12-23 at 19:41 +0530, Kumar Gopalpet-B05799 wrote: > >> Hi all, >> >> I am trying linux 2.6.32-rc3 in SMP mode. I am seeing a lot of BAD >> interrupts when I do a "cat /proc/interrupts". >> >> I am running a forwarding application b/w two ethernet ports (ethernet >> uses gianfar driver). >> >> Has any one observed these BAD interrupts ? If so, can someone help me >> in understanding why these interrupts come and how to resolve it ? >> > > You'll need to tell us what platform you're running on. > > The BAD interrupts come from ppc_spurious_interrupts. It's a count of > the number of times we entered do_IRQ() (ie. took an external > interrupt), but when we asked the interrupt controller which irq it was, > the interrupt controller said there was no irq. > > Depending on your interrupt controller that might happen sometimes for > valid reasons. Or it might indicate something is setup wrong. > > cheers > I think it will help to show us your /proc/interrupts so that how you suffered from bad interrupts. ^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: [HELP] BAD interrupts 2009-12-24 11:46 ` gshan @ 2009-12-24 10:45 ` Kumar Gopalpet-B05799 2009-12-31 8:12 ` Régis Odeyé 0 siblings, 1 reply; 5+ messages in thread From: Kumar Gopalpet-B05799 @ 2009-12-24 10:45 UTC (permalink / raw) To: gshan, michael, avorontsov; +Cc: netdev, linuxppc-dev [-- Attachment #1: Type: text/plain, Size: 1814 bytes --] >-----Original Message----- >From: gshan [mailto:gshan@alcatel-lucent.com] >Sent: Thursday, December 24, 2009 5:16 PM >To: michael@ellerman.id.au >Cc: Kumar Gopalpet-B05799; netdev@vger.kernel.org; >linuxppc-dev@lists.ozlabs.org >Subject: Re: [HELP] BAD interrupts > >Michael Ellerman wrote: >> On Wed, 2009-12-23 at 19:41 +0530, Kumar Gopalpet-B05799 wrote: >> >>> Hi all, >>> >>> I am trying linux 2.6.32-rc3 in SMP mode. I am seeing a lot of BAD >>> interrupts when I do a "cat /proc/interrupts". >>> >>> I am running a forwarding application b/w two ethernet ports >>> (ethernet uses gianfar driver). >>> >>> Has any one observed these BAD interrupts ? If so, can someone help >>> me in understanding why these interrupts come and how to >resolve it ? >>> >> >> You'll need to tell us what platform you're running on. >> >> The BAD interrupts come from ppc_spurious_interrupts. It's a >count of >> the number of times we entered do_IRQ() (ie. took an external >> interrupt), but when we asked the interrupt controller which irq it >> was, the interrupt controller said there was no irq. >> >> Depending on your interrupt controller that might happen >sometimes for >> valid reasons. Or it might indicate something is setup wrong. >> >> cheers >> >I think it will help to show us your /proc/interrupts so that >how you suffered from bad interrupts. > I am running linux-2.6.29 in SMP mode on P2020RDB ( ruuning at 1200/600/667). The test scenario forwarding application and is a bidirectioanl flow between eth0 & eth2. Attached is the complete log of the test scenario. I also noted another observation that when all the interrupts are mapped to a single core, the BAD interrupts stop coming. -- Thanks Sandeep [-- Attachment #2: smp_log_bad_intrs.txt --] [-- Type: text/plain, Size: 27221 bytes --] tftp 1000000 etsec2/uImage_alpha Speed: 1000, full duplex Using eTSEC1 device TFTP from server 10.232.134.194; our IP address is 10.232.133.188 Filename 'etsec2/uImage_alpha'. Load address: 0x1000000 Loading: *\b################################################################# ################################################################# ################################################### done Bytes transferred = 2654090 (287f8a hex) => tftp 2000000 etsec2/rf\b \bootfs_alpha Speed: 1000, full duplex Using eTSEC1 device TFTP from server 10.232.134.194; our IP address is 10.232.133.188 Filename 'etsec2/rootfs_alpha'. Load address: 0x2000000 Loading: *\b################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### done Bytes transferred = 26776875 (198952b hex) => tftp c00000 etsec2/p2020alpha.dtb Speed: 1000, full duplex Using eTSEC1 device TFTP from server 10.232.134.194; our IP address is 10.232.133.188 Filename 'etsec2/p2020alpha.dtb'. Load address: 0xc00000 Loading: *\b# done Bytes transferred = 10579 (2953 hex) => bootm 1000000 2000000 c00000 WARNING: adjusting available memory to 30000000 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux-2.6.29 Created: 2009-07-03 9:42:06 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2654026 Bytes = 2.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: uboot ext2 ramdisk rootfs Created: 2009-07-04 8:24:27 UTC Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 26776811 Bytes = 25.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 00c00000 Booting using the fdt blob at 0xc00000 Uncompressing Kernel Image ... OK Loading Ramdisk to 2e676000, end 2ffff4eb ... OK Using P2020 RDB machine description Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=256Mb residual: 256Mb Linux version 2.6.29 (dipen@uTeam3.ap.freescale.net) (gcc version 4.3.2 (GCC) ) #1 SMP Fri Jul 3 15:11:50 IST 2009 Found initrd at 0xee676000:0xeffff4eb CPU maps initialized for 1 thread per core console [udbg0] enabled setup_arch: bootmem mpc85xx_rdb_setup_arch() Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->255 PCI host bridge /pcie@ffe09000 ranges: MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000 IO 0x00000000ffc30000..0x00000000ffc3ffff -> 0x0000000000000000 Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->255 PCI host bridge /pcie@ffe0a000 ranges: MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000 IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000 MPC85xx RDB board from Freescale Semiconductor arch: exit Zone PFN ranges: DMA 0x00000000 -> 0x00030000 Normal 0x00030000 -> 0x00030000 HighMem 0x00030000 -> 0x00040000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00040000 MMU: Allocated 1088 bytes of context maps for 255 contexts Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 Kernel command line: root=/dev/ram rw console=ttyS0,115200 ramdisk_size=275000 cache-sram-size=0x10000 mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs mpic: ISU size: 256, shift: 8, mask: ff mpic: Initializing for 256 sources PID hash table entries: 4096 (order: 12, 16384 bytes) clocksource: timebase mult[3555555] shift[22] registered Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1007184k/1048576k available (5180k kernel code, 40848k reserved, 164k data, 134k bss, 216k init) SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Calibrating delay loop... 149.50 BogoMIPS (lpj=299008) Mount-cache hash table entries: 512 mpic: requesting IPIs ... Processor 1 found. Brought up 2 CPUs net_namespace: 732 bytes NET: Registered protocol family 16 PCI: Probing PCI hardware pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01) pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0001:02:00.0: ignoring class b20 (doesn't match header type 01) pci 0001:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0001:02:00.0: PME# disabled pci 0000:00:00.0: not setting up bridge for bus 0000:01 pci 0000:00:00.0: enabling device (0106 -> 0107) pci 0001:02:00.0: not setting up bridge for bus 0001:03 pci 0001:02:00.0: enabling device (0106 -> 0107) bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Freescale Elo / Elo Plus DMA driver NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 26149k freed fsl-elo-dma ffe0c300.dma: Probe the Freescale DMA driver for fsl,eloplus-dma controller at ffe0c300... fsl-elo-dma ffe0c300.dma: #0 (fsl,eloplus-dma-channel), irq 76 fsl-elo-dma ffe0c300.dma: #1 (fsl,eloplus-dma-channel), irq 77 fsl-elo-dma ffe0c300.dma: #2 (fsl,eloplus-dma-channel), irq 78 fsl-elo-dma ffe0c300.dma: #3 (fsl,eloplus-dma-channel), irq 79 fsl-elo-dma ffe21300.dma: Probe the Freescale DMA driver for fsl,eloplus-dma controller at ffe21300... fsl-elo-dma ffe21300.dma: #0 (fsl,eloplus-dma-channel), irq 20 fsl-elo-dma ffe21300.dma: #1 (fsl,eloplus-dma-channel), irq 21 fsl-elo-dma ffe21300.dma: #2 (fsl,eloplus-dma-channel), irq 22 fsl-elo-dma ffe21300.dma: #3 (fsl,eloplus-dma-channel), irq 23 audit: initializing netlink socket (disabled) type=2000 audit(2.388:1): initialized highmem bounce pool size: 64 pages Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.29 [Flags: R/O]. JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. JFFS2: default compression mode: priority msgmni has been set to 1507 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Generic non-volatile memory driver v1.1 Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A console handover: boot [udbg0] -> real [ttyS0] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A brd: module loaded loop: module loaded nbd: registered device at major 43 e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6 e1000e: Copyright (c) 1999-2008 Intel Corporation. Gianfar MII Bus: probed Gianfar MII Bus: probed eth0 (fsl-gianfar): not using net_device_ops yet eth0: Gianfar Ethernet Controller Version 1.4-skbr1.1.4, 00:04:9f:0c:05:00 eth0: MTU = 1500 (frame size=1524, truesize=1800) eth0: Running with NAPI enabled eth0: 128/128 RX/TX BD ring size eth1 (fsl-gianfar): not using net_device_ops yet eth1: Gianfar Ethernet Controller Version 1.4-skbr1.1.4, 00:04:9f:0c:05:01 eth1: MTU = 1500 (frame size=1524, truesize=1800) eth1: Running with NAPI enabled eth1: 128/128 RX/TX BD ring size eth2 (fsl-gianfar): not using net_device_ops yet eth2: Gianfar Ethernet Controller Version 1.4-skbr1.1.4, 00:04:9f:0c:05:02 eth2: MTU = 1500 (frame size=1524, truesize=1800) eth2: Running with NAPI enabled eth2: 128/128 RX/TX BD ring size Fixed MDIO Bus: probed st: Version 20081215, fixed bufsize 32768, s/g segs 256 Driver 'st' needs updating - please use bus_type methods Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 ef000000.nor: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Creating 5 MTD partitions on "ef000000.nor": 0x000000000000-0x000000040000 : "NOR (RO) Vitesse-7385 Firmware" ftl_cs: FTL header not found. 0x000000040000-0x000000080000 : "NOR (RO) DTB Image" ftl_cs: FTL header not found. 0x000000080000-0x000000400000 : "NOR (RO) Linux Kernel Image" ftl_cs: FTL header not found. 0x000000400000-0x000000f00000 : "NOR (RW) JFFS2 Root File System" ftl_cs: FTL header not found. 0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image" ftl_cs: FTL header not found. NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit) RedBoot partition parsing not available Creating 6 MTD partitions on "ffa00000.flash": 0x000000000000-0x000000080000 : "NAND (RO) U-Boot Image" ftl_cs: FTL header not found. 0x000000080000-0x000000100000 : "NAND (RO) DTB Image" ftl_cs: FTL header not found. 0x000000100000-0x000000500000 : "NAND (RO) Linux Kernel Image" ftl_cs: FTL header not found. 0x000000500000-0x000000900000 : "NAND (RO) Compressed RFS Image" ftl_cs: FTL header not found. 0x000000900000-0x000001000000 : "NAND (RW) JFFS2 Root File System" ftl_cs: FTL header not found. 0x000001000000-0x000002000000 : "NAND (RW) Writable User area" ftl_cs: FTL header not found. eLBC NAND device at 0xffa00000, bank 1 fsl_m25p80 spi28672.0: s25sl128b (0 Kbytes) Creating 5 MTD partitions on "SPIFLASH0": 0x000000000000-0x000000080000 : "SPI (RO) U-Boot Image" ftl_cs: FTL header not found. 0x000000080000-0x000000100000 : "SPI (RO) DTB Image" ftl_cs: FTL header not found. 0x000000100000-0x000000500000 : "SPI (RO) Linux Kernel Image" ftl_cs: FTL header not found. 0x000000500000-0x000000900000 : "SPI (RO) Compressed RFS Image" ftl_cs: FTL header not found. 0x000000900000-0x000001000000 : "SPI (RW) JFFS2 RFS" ftl_cs: FTL header not found. ffe07000.spi: Freescale eSPI Controller driver at 0xf210a000 (irq = 59) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i2c /dev entries driver rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0 sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman esdhc: Freescale Enhanced Secure Digital Host Controller driver mmc0: ESDHC at 0xffe2e000 irq 72 PIO talitos ffe30000.crypto: hwrng alg: No test for authenc(hmac(sha1),cbc(aes)) (authenc-hmac-sha1-cbc-aes-talitos) talitos ffe30000.crypto: authenc-hmac-sha1-cbc-aes-talitos alg: No test for authenc(hmac(sha1),cbc(des3_ede)) (authenc-hmac-sha1-cbc-3des-talitos) talitos ffe30000.crypto: authenc-hmac-sha1-cbc-3des-talitos alg: No test for authenc(hmac(sha256),cbc(aes)) (authenc-hmac-sha256-cbc-aes-talitos) talitos ffe30000.crypto: authenc-hmac-sha256-cbc-aes-talitos alg: No test for authenc(hmac(sha256),cbc(des3_ede)) (authenc-hmac-sha256-cbc-3des-talitos) talitos ffe30000.crypto: authenc-hmac-sha256-cbc-3des-talitos alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-talitos) talitos ffe30000.crypto: authenc-hmac-md5-cbc-aes-talitos alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-3des-talitos) talitos ffe30000.crypto: authenc-hmac-md5-cbc-3des-talitos IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 RPC: Registered udp transport module. RPC: Registered tcp transport module. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> rtc-ds1307 0-0068: setting system clock to 2009-07-01 10:24:20 UTC (1246443860) RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem) on device 1:0. Freeing unused kernel memory: 216k init Mounting /proc and /sys Setting the hostname to P2020RDB Mounting filesystems mount: sysfs already mounted or /sys busy mount: according to mtab, /sys is already mounted on /sys Starting syslogd and klogd Running sysctl Setting up networking on loopback device: Setting up networking on eth0: ADDRCONF(NETDEV_UP): eth0: link is not ready Adding static route for default gateway to 192.168.0.1: Setting nameserver to 192.168.0.1 in /etc/resolv.conf: SettingADDRCONF(NETDEV_UP): eth1: link is not ready up networking on eth1: Adding static route for default gateway to 192.168.1.1: Setting nameserver to 192.168.1.1 in /etc/resolv.conf: SettingADDRCONF(NETDEV_UP): eth2: link is not ready up networking on eth2: Adding static route for default gateway to 192.168.2.1: Starting inetd: Starting the port mapper: Generating keys for the dropbear ssh server: Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key' Generating key, this may take a while... Public key portion is: ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwC8sk4V/7x6e0hJOjBdcGmUx26QQfpVdxT1z9itBPZf/bdfogKI5OHEfCPU2Tc+ZYNtrPXIgYvrML5I5z/WQL7QNgOx0/Vv woNbxHLXj5UmirIJ6kNKlyUisPyZNU54XQjKCTpK7GjcGvUFgQMqv2HqWMfFV9XmytvXJgkhyg0jxox7 root@P2020RDB Fingerprint: md5 2d:50:46:59:d1:92:72:1f:07:cf:e4:b6:14:6c:86:f3 Starting the dropbear ssh server: Starting the boa webserver: Please set the system time using date <mmddhhmnyyyy> /sbin/hwclock -w PHY: 0:01 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Welcome to Freescale Semiconductor Embedded Linux Environment !!!!! WARNING !!!!!!! The default password for the root account is: root please change this password using the 'passwd' command and then edit this message (/etc/issue) to remove this message P2020RDB login: PHY: mdio0@520:01 - Link is Up - 1000/Full ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready root Password: [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig eth0 down [root@P2020RDB /root]# [root@P2020RDB /root]# ifconfig eth0 down\b\b\b\b\b\b down 1 down down [root@P2020RDB /root]# [root@P2020RDB /root]# ifconfig eth1 down\b\b\b\b\b\b down 2 down down [root@P2020RDB /root]# [root@P2020RDB /root]# [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig eth0 192.168.1.2 netmask 255.255.255.0 [root@P2020RDB /root]# PHY: 0:01 - Link is Up - 1000/Full [root@P2020RDB /root]# ifcoe\b \b\b\b\b\b[root@P2020RDB /root]# ifconfig t\b \beyh\b \b\b \bth2 192.168.2.2 netmask 255.255.255.0 [root@P2020RDB /root]# PHY: mdio0@520:01 - Link is Up - 1000/Full [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig eth\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \beccho 1 > /p\b\b[root@P2020RDB /root]# eccho 1 > /proc/sy[root@P2020RDB /root]# eccho 1 > /proc/sys/n[root@P2020RDB /root]# eccho 1 > /proc/sys/net/ip[root@P2020RDB /root]# eccho 1 > /proc/sys/net/ipv4[root@P2020RDB /root]# eccho 1 > /proc/sys/net/ipv4/ip_f[root@P2020RDB /root]# eccho 1 > /proc/sys/net/ipv4/ip_forward -sh: eccho: not found [root@P2020RDB /root]# echo 1 > /p\b\b[root@P2020RDB /root]# echo 1 > /proc/sy[root@P2020RDB /root]# echo 1 > /proc/sys/n[root@P2020RDB /root]# echo 1 > /proc/sys/net/ip[root@P2020RDB /root]# echo 1 > /proc/sys/net/ipv4[root@P2020RDB /root]# echo 1 > /proc/sys/net/ipv4/ip_f[root@P2020RDB /root]# echo 1 > /proc/sys/net/ipv4/ip_forward [root@P2020RDB /root]# [root@P2020RDB /root]# [root@P2020RDB /root]# pn\b \bing 192.168.1.1 PING 192.168.1.1 (192.168.1.1): 56 data bytes 64 bytes from 192.168.1.1: seq=0 ttl=255 time=2.590 ms 64 bytes from 192.168.1.1: seq=1 ttl=255 time=0.090 ms --- 192.168.1.1 ping statistics --- 2 packets transmitted, 2 packets received, 0% packet loss round-trip min/avg/max = 0.090/1.340/2.590 ms [root@P2020RDB /root]# [root@P2020RDB /root]# [root@P2020RDB /root]# ping 192.168.2.1 PING 192.168.2.1 (192.168.2.1): 56 data bytes 64 bytes from 192.168.2.1: seq=0 ttl=255 time=3.502 ms --- 192.168.2.1 ping statistics --- 1 packets transmitted, 1 packets received, 0% packet loss round-trip min/avg/max = 3.502/3.502/3.502 ms [root@P2020RDB /root]# arp gateway2 (192.168.2.1) at 00:00:08:00:00:01 [ether] on eth2 gateway1 (192.168.1.1) at 00:00:07:00:00:01 [ether] on eth0 [root@P2020RDB /root]# arp -s 192.168.2.1 00:00:08:00:00:01 [root@P2020RDB /root]# arp -s 192.1681.\b \b\b \b.1.1 00:00:07:00:00:01 [root@P2020RDB /root]# [root@P2020RDB /root]# [root@P2020RDB /root]# [root@P2020RDB /root]# arp gateway2 (192.168.2.1) at 00:00:08:00:00:01 [ether] PERM on eth2 gateway1 (192.168.1.1) at 00:00:07:00:00:01 [ether] PERM on eth0 [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig eth0 Link encap:Ethernet HWaddr 00:04:9F:0C:05:00 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:426 (426.0 B) TX bytes:1146 (1.1 KiB) Base address:0x2000 eth2 Link encap:Ethernet HWaddr 00:04:9F:0C:05:02 inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:318 (318.0 B) TX bytes:1048 (1.0 KiB) Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) [root@P2020RDB /root]# cat /p\b\b[root@P2020RDB /root]# cat /proc/in[root@P2020RDB /root]# cat /proc/interrupts CPU0 CPU1 19: 648 0 OpenPIC Level fsl-elbc 20: 0 0 OpenPIC Level fsldma-channel 21: 0 0 OpenPIC Level fsldma-channel 22: 0 0 OpenPIC Level fsldma-channel 23: 0 0 OpenPIC Level fsldma-channel 28: 0 0 OpenPIC Level ehci_hcd:usb1 29: 13 0 OpenPIC Level eth0_tx 30: 0 4 OpenPIC Level eth0_rx 31: 0 12 OpenPIC Level eth2_tx 32: 4 0 OpenPIC Level eth2_rx 33: 0 0 OpenPIC Level eth2_er 34: 0 0 OpenPIC Level eth0_er 42: 1049 0 OpenPIC Level serial 43: 0 29 OpenPIC Level i2c-mpc, i2c-mpc 45: 0 0 OpenPIC Level talitos 59: 0 2494 OpenPIC Level fsl_espi 72: 12 0 OpenPIC Level esdhc:slot0 76: 0 0 OpenPIC Level fsldma-channel 77: 0 0 OpenPIC Level fsldma-channel 78: 0 0 OpenPIC Level fsldma-channel 79: 0 0 OpenPIC Level fsldma-channel 251: 0 0 OpenPIC Edge ipi call function 252: 1253 1387 OpenPIC Edge ipi reschedule 253: 427 390 OpenPIC Edge ipi call function single BAD: 1 [root@P2020RDB /root]# PHY: mdio0@520:01 - Link is Down PHY: mdio0@520:01 - Link is Up - 1000/Full [root@P2020RDB /root]# cat /p\b\b[root@P2020RDB /root]# cat /proc/in[root@P2020RDB /root]# cat /proc/interrupts CPU0 CPU1 19: 648 0 OpenPIC Level fsl-elbc 20: 0 0 OpenPIC Level fsldma-channel 21: 0 0 OpenPIC Level fsldma-channel 22: 0 0 OpenPIC Level fsldma-channel 23: 0 0 OpenPIC Level fsldma-channel 28: 0 0 OpenPIC Level ehci_hcd:usb1 29: 56328 0 OpenPIC Level eth0_tx 30: 0 5553282 OpenPIC Level eth0_rx 31: 0 43413 OpenPIC Level eth2_tx 32: 5709572 0 OpenPIC Level eth2_rx 33: 0 0 OpenPIC Level eth2_er 34: 0 0 OpenPIC Level eth0_er 42: 1179 0 OpenPIC Level serial 43: 0 29 OpenPIC Level i2c-mpc, i2c-mpc 45: 0 0 OpenPIC Level talitos 59: 0 2494 OpenPIC Level fsl_espi 72: 12 0 OpenPIC Level esdhc:slot0 76: 0 0 OpenPIC Level fsldma-channel 77: 0 0 OpenPIC Level fsldma-channel 78: 0 0 OpenPIC Level fsldma-channel 79: 0 0 OpenPIC Level fsldma-channel 251: 0 0 OpenPIC Edge ipi call function 252: 1254 1389 OpenPIC Edge ipi reschedule 253: 427 406 OpenPIC Edge ipi call function single BAD: 36172 [root@P2020RDB /root]# uname -a Linux P2020RDB 2.6.29 #1 SMP Fri Jul 3 15:11:50 IST 2009 ppc unknown [root@P2020RDB /root]# cat /p\b\b[root@P2020RDB /root]# cat /proc/in[root@P2020RDB /root]# cat /proc/interrupts CPU0 CPU1 19: 648 0 OpenPIC Level fsl-elbc 20: 0 0 OpenPIC Level fsldma-channel 21: 0 0 OpenPIC Level fsldma-channel 22: 0 0 OpenPIC Level fsldma-channel 23: 0 0 OpenPIC Level fsldma-channel 28: 0 0 OpenPIC Level ehci_hcd:usb1 29: 56328 0 OpenPIC Level eth0_tx 30: 0 5553282 OpenPIC Level eth0_rx 31: 0 43413 OpenPIC Level eth2_tx 32: 5709572 0 OpenPIC Level eth2_rx 33: 0 0 OpenPIC Level eth2_er 34: 0 0 OpenPIC Level eth0_er 42: 1329 0 OpenPIC Level serial 43: 0 29 OpenPIC Level i2c-mpc, i2c-mpc 45: 0 0 OpenPIC Level talitos 59: 0 2494 OpenPIC Level fsl_espi 72: 12 0 OpenPIC Level esdhc:slot0 76: 0 0 OpenPIC Level fsldma-channel 77: 0 0 OpenPIC Level fsldma-channel 78: 0 0 OpenPIC Level fsldma-channel 79: 0 0 OpenPIC Level fsldma-channel 251: 0 0 OpenPIC Edge ipi call function 252: 1256 1391 OpenPIC Edge ipi reschedule 253: 427 439 OpenPIC Edge ipi call function single BAD: 36172 [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig eth0 Link encap:Ethernet HWaddr 00:04:9F:0C:05:00 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8928576 errors:0 dropped:0 overruns:0 frame:0 TX packets:8928586 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:625000396 (596.0 MiB) TX bytes:535715406 (510.8 MiB) Base address:0x2000 eth2 Link encap:Ethernet HWaddr 00:04:9F:0C:05:02 inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8928575 errors:0 dropped:0 overruns:0 frame:0 TX packets:8928585 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:625000288 (596.0 MiB) TX bytes:535715308 (510.8 MiB) Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) [root@P2020RDB /root]# ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [HELP] BAD interrupts 2009-12-24 10:45 ` Kumar Gopalpet-B05799 @ 2009-12-31 8:12 ` Régis Odeyé 0 siblings, 0 replies; 5+ messages in thread From: Régis Odeyé @ 2009-12-31 8:12 UTC (permalink / raw) To: Kumar Gopalpet-B05799; +Cc: gshan, avorontsov, linuxppc-dev, netdev Hi, We experimented something similar with a 8641D board. This seems to come from the gianfar and: - when we are binding the three interruptions enet_tx, enet_rx and enet_err of each interfaces on the same processor, the BAD interruptions do not increase any more. - when we are compiling the driver without the NAPI mode, there is no more BAD interruptions at all. Hope it will help even if we did not find a real fix. Regards. Régis. Kumar Gopalpet-B05799 wrote: > > > >> -----Original Message----- >> From: gshan [mailto:gshan@alcatel-lucent.com] >> Sent: Thursday, December 24, 2009 5:16 PM >> To: michael@ellerman.id.au >> Cc: Kumar Gopalpet-B05799; netdev@vger.kernel.org; >> linuxppc-dev@lists.ozlabs.org >> Subject: Re: [HELP] BAD interrupts >> >> Michael Ellerman wrote: >> >>> On Wed, 2009-12-23 at 19:41 +0530, Kumar Gopalpet-B05799 wrote: >>> >>> >>>> Hi all, >>>> >>>> I am trying linux 2.6.32-rc3 in SMP mode. I am seeing a lot of BAD >>>> interrupts when I do a "cat /proc/interrupts". >>>> >>>> I am running a forwarding application b/w two ethernet ports >>>> (ethernet uses gianfar driver). >>>> >>>> Has any one observed these BAD interrupts ? If so, can someone help >>>> me in understanding why these interrupts come and how to >>>> >> resolve it ? >> >>>> >>>> >>> You'll need to tell us what platform you're running on. >>> >>> The BAD interrupts come from ppc_spurious_interrupts. It's a >>> >> count of >> >>> the number of times we entered do_IRQ() (ie. took an external >>> interrupt), but when we asked the interrupt controller which irq it >>> was, the interrupt controller said there was no irq. >>> >>> Depending on your interrupt controller that might happen >>> >> sometimes for >> >>> valid reasons. Or it might indicate something is setup wrong. >>> >>> cheers >>> >>> >> I think it will help to show us your /proc/interrupts so that >> how you suffered from bad interrupts. >> >> > > I am running linux-2.6.29 in SMP mode on P2020RDB ( ruuning at > 1200/600/667). The test scenario forwarding > application and is a bidirectioanl flow between eth0 & eth2. > > Attached is the complete log of the test scenario. > > I also noted another observation that when all the interrupts are mapped > to a single core, the BAD interrupts stop coming. > > -- > > Thanks > Sandeep > > > ------------------------------------------------------------------------ > > tftp 1000000 etsec2/uImage_alpha > Speed: 1000, full duplex > Using eTSEC1 device > TFTP from server 10.232.134.194; our IP address is 10.232.133.188 > Filename 'etsec2/uImage_alpha'. > Load address: 0x1000000 > Loading: *\b################################################################# > ################################################################# > ################################################### > done > Bytes transferred = 2654090 (287f8a hex) > => tftp 2000000 etsec2/rf\b \bootfs_alpha > Speed: 1000, full duplex > Using eTSEC1 device > TFTP from server 10.232.134.194; our IP address is 10.232.133.188 > Filename 'etsec2/rootfs_alpha'. > Load address: 0x2000000 > Loading: *\b################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ##### > done > Bytes transferred = 26776875 (198952b hex) > => tftp c00000 etsec2/p2020alpha.dtb > Speed: 1000, full duplex > Using eTSEC1 device > TFTP from server 10.232.134.194; our IP address is 10.232.133.188 > Filename 'etsec2/p2020alpha.dtb'. > Load address: 0xc00000 > Loading: *\b# > done > Bytes transferred = 10579 (2953 hex) > => bootm 1000000 2000000 c00000 > WARNING: adjusting available memory to 30000000 > ## Booting kernel from Legacy Image at 01000000 ... > Image Name: Linux-2.6.29 > Created: 2009-07-03 9:42:06 UTC > Image Type: PowerPC Linux Kernel Image (gzip compressed) > Data Size: 2654026 Bytes = 2.5 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > ## Loading init Ramdisk from Legacy Image at 02000000 ... > Image Name: uboot ext2 ramdisk rootfs > Created: 2009-07-04 8:24:27 UTC > Image Type: PowerPC Linux RAMDisk Image (gzip compressed) > Data Size: 26776811 Bytes = 25.5 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > ## Flattened Device Tree blob at 00c00000 > Booting using the fdt blob at 0xc00000 > Uncompressing Kernel Image ... OK > Loading Ramdisk to 2e676000, end 2ffff4eb ... OK > Using P2020 RDB machine description > Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=256Mb residual: 256Mb > Linux version 2.6.29 (dipen@uTeam3.ap.freescale.net) (gcc version 4.3.2 (GCC) ) #1 SMP Fri Jul 3 15:11:50 IST 2009 > Found initrd at 0xee676000:0xeffff4eb > CPU maps initialized for 1 thread per core > console [udbg0] enabled > setup_arch: bootmem > mpc85xx_rdb_setup_arch() > Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->255 > PCI host bridge /pcie@ffe09000 ranges: > MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000 > IO 0x00000000ffc30000..0x00000000ffc3ffff -> 0x0000000000000000 > Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->255 > PCI host bridge /pcie@ffe0a000 ranges: > MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000 > IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000 > MPC85xx RDB board from Freescale Semiconductor > arch: exit > Zone PFN ranges: > DMA 0x00000000 -> 0x00030000 > Normal 0x00030000 -> 0x00030000 > HighMem 0x00030000 -> 0x00040000 > Movable zone start PFN for each node > early_node_map[1] active PFN ranges > 0: 0x00000000 -> 0x00040000 > MMU: Allocated 1088 bytes of context maps for 255 contexts > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 > Kernel command line: root=/dev/ram rw console=ttyS0,115200 ramdisk_size=275000 cache-sram-size=0x10000 > mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs > mpic: ISU size: 256, shift: 8, mask: ff > mpic: Initializing for 256 sources > PID hash table entries: 4096 (order: 12, 16384 bytes) > clocksource: timebase mult[3555555] shift[22] registered > Console: colour dummy device 80x25 > Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) > Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) > Memory: 1007184k/1048576k available (5180k kernel code, 40848k reserved, 164k data, 134k bss, 216k init) > SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 > Calibrating delay loop... 149.50 BogoMIPS (lpj=299008) > Mount-cache hash table entries: 512 > mpic: requesting IPIs ... > Processor 1 found. > Brought up 2 CPUs > net_namespace: 732 bytes > NET: Registered protocol family 16 > > PCI: Probing PCI hardware > pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01) > pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold > pci 0000:00:00.0: PME# disabled > pci 0001:02:00.0: ignoring class b20 (doesn't match header type 01) > pci 0001:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold > pci 0001:02:00.0: PME# disabled > pci 0000:00:00.0: not setting up bridge for bus 0000:01 > pci 0000:00:00.0: enabling device (0106 -> 0107) > pci 0001:02:00.0: not setting up bridge for bus 0001:03 > pci 0001:02:00.0: enabling device (0106 -> 0107) > bio: create slab <bio-0> at 0 > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > Freescale Elo / Elo Plus DMA driver > NET: Registered protocol family 2 > IP route cache hash table entries: 32768 (order: 5, 131072 bytes) > TCP established hash table entries: 131072 (order: 8, 1048576 bytes) > TCP bind hash table entries: 65536 (order: 7, 524288 bytes) > TCP: Hash tables configured (established 131072 bind 65536) > TCP reno registered > NET: Registered protocol family 1 > checking if image is initramfs...it isn't (no cpio magic); looks like an initrd > Freeing initrd memory: 26149k freed > fsl-elo-dma ffe0c300.dma: Probe the Freescale DMA driver for fsl,eloplus-dma controller at ffe0c300... > fsl-elo-dma ffe0c300.dma: #0 (fsl,eloplus-dma-channel), irq 76 > fsl-elo-dma ffe0c300.dma: #1 (fsl,eloplus-dma-channel), irq 77 > fsl-elo-dma ffe0c300.dma: #2 (fsl,eloplus-dma-channel), irq 78 > fsl-elo-dma ffe0c300.dma: #3 (fsl,eloplus-dma-channel), irq 79 > fsl-elo-dma ffe21300.dma: Probe the Freescale DMA driver for fsl,eloplus-dma controller at ffe21300... > fsl-elo-dma ffe21300.dma: #0 (fsl,eloplus-dma-channel), irq 20 > fsl-elo-dma ffe21300.dma: #1 (fsl,eloplus-dma-channel), irq 21 > fsl-elo-dma ffe21300.dma: #2 (fsl,eloplus-dma-channel), irq 22 > fsl-elo-dma ffe21300.dma: #3 (fsl,eloplus-dma-channel), irq 23 > audit: initializing netlink socket (disabled) > type=2000 audit(2.388:1): initialized > highmem bounce pool size: 64 pages > Installing knfsd (copyright (C) 1996 okir@monad.swb.de). > NTFS driver 2.1.29 [Flags: R/O]. > JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. > JFFS2: default compression mode: priority > msgmni has been set to 1507 > alg: No test for stdrng (krng) > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > Generic non-volatile memory driver v1.1 > Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled > serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A > console handover: boot [udbg0] -> real [ttyS0] > serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A > brd: module loaded > loop: module loaded > nbd: registered device at major 43 > e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6 > e1000e: Copyright (c) 1999-2008 Intel Corporation. > Gianfar MII Bus: probed > Gianfar MII Bus: probed > eth0 (fsl-gianfar): not using net_device_ops yet > eth0: Gianfar Ethernet Controller Version 1.4-skbr1.1.4, 00:04:9f:0c:05:00 > eth0: MTU = 1500 (frame size=1524, truesize=1800) > eth0: Running with NAPI enabled > eth0: 128/128 RX/TX BD ring size > eth1 (fsl-gianfar): not using net_device_ops yet > eth1: Gianfar Ethernet Controller Version 1.4-skbr1.1.4, 00:04:9f:0c:05:01 > eth1: MTU = 1500 (frame size=1524, truesize=1800) > eth1: Running with NAPI enabled > eth1: 128/128 RX/TX BD ring size > eth2 (fsl-gianfar): not using net_device_ops yet > eth2: Gianfar Ethernet Controller Version 1.4-skbr1.1.4, 00:04:9f:0c:05:02 > eth2: MTU = 1500 (frame size=1524, truesize=1800) > eth2: Running with NAPI enabled > eth2: 128/128 RX/TX BD ring size > Fixed MDIO Bus: probed > st: Version 20081215, fixed bufsize 32768, s/g segs 256 > Driver 'st' needs updating - please use bus_type methods > Driver 'sd' needs updating - please use bus_type methods > Driver 'sr' needs updating - please use bus_type methods > ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank > Amd/Fujitsu Extended Query Table at 0x0040 > ef000000.nor: CFI does not contain boot bank location. Assuming top. > number of CFI chips: 1 > cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. > RedBoot partition parsing not available > Creating 5 MTD partitions on "ef000000.nor": > 0x000000000000-0x000000040000 : "NOR (RO) Vitesse-7385 Firmware" > ftl_cs: FTL header not found. > 0x000000040000-0x000000080000 : "NOR (RO) DTB Image" > ftl_cs: FTL header not found. > 0x000000080000-0x000000400000 : "NOR (RO) Linux Kernel Image" > ftl_cs: FTL header not found. > 0x000000400000-0x000000f00000 : "NOR (RW) JFFS2 Root File System" > ftl_cs: FTL header not found. > 0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image" > ftl_cs: FTL header not found. > NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit) > RedBoot partition parsing not available > Creating 6 MTD partitions on "ffa00000.flash": > 0x000000000000-0x000000080000 : "NAND (RO) U-Boot Image" > ftl_cs: FTL header not found. > 0x000000080000-0x000000100000 : "NAND (RO) DTB Image" > ftl_cs: FTL header not found. > 0x000000100000-0x000000500000 : "NAND (RO) Linux Kernel Image" > ftl_cs: FTL header not found. > 0x000000500000-0x000000900000 : "NAND (RO) Compressed RFS Image" > ftl_cs: FTL header not found. > 0x000000900000-0x000001000000 : "NAND (RW) JFFS2 Root File System" > ftl_cs: FTL header not found. > 0x000001000000-0x000002000000 : "NAND (RW) Writable User area" > ftl_cs: FTL header not found. > eLBC NAND device at 0xffa00000, bank 1 > fsl_m25p80 spi28672.0: s25sl128b (0 Kbytes) > Creating 5 MTD partitions on "SPIFLASH0": > 0x000000000000-0x000000080000 : "SPI (RO) U-Boot Image" > ftl_cs: FTL header not found. > 0x000000080000-0x000000100000 : "SPI (RO) DTB Image" > ftl_cs: FTL header not found. > 0x000000100000-0x000000500000 : "SPI (RO) Linux Kernel Image" > ftl_cs: FTL header not found. > 0x000000500000-0x000000900000 : "SPI (RO) Compressed RFS Image" > ftl_cs: FTL header not found. > 0x000000900000-0x000001000000 : "SPI (RW) JFFS2 RFS" > ftl_cs: FTL header not found. > ffe07000.spi: Freescale eSPI Controller driver at 0xf210a000 (irq = 59) > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller > fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 > fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000 > fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > i2c /dev entries driver > rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0 > sdhci: Secure Digital Host Controller Interface driver > sdhci: Copyright(c) Pierre Ossman > esdhc: Freescale Enhanced Secure Digital Host Controller driver > mmc0: ESDHC at 0xffe2e000 irq 72 PIO > talitos ffe30000.crypto: hwrng > alg: No test for authenc(hmac(sha1),cbc(aes)) (authenc-hmac-sha1-cbc-aes-talitos) > talitos ffe30000.crypto: authenc-hmac-sha1-cbc-aes-talitos > alg: No test for authenc(hmac(sha1),cbc(des3_ede)) (authenc-hmac-sha1-cbc-3des-talitos) > talitos ffe30000.crypto: authenc-hmac-sha1-cbc-3des-talitos > alg: No test for authenc(hmac(sha256),cbc(aes)) (authenc-hmac-sha256-cbc-aes-talitos) > talitos ffe30000.crypto: authenc-hmac-sha256-cbc-aes-talitos > alg: No test for authenc(hmac(sha256),cbc(des3_ede)) (authenc-hmac-sha256-cbc-3des-talitos) > talitos ffe30000.crypto: authenc-hmac-sha256-cbc-3des-talitos > alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-talitos) > talitos ffe30000.crypto: authenc-hmac-md5-cbc-aes-talitos > alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-3des-talitos) > talitos ffe30000.crypto: authenc-hmac-md5-cbc-3des-talitos > IPv4 over IPv4 tunneling driver > GRE over IPv4 tunneling driver > TCP cubic registered > Initializing XFRM netlink socket > NET: Registered protocol family 10 > IPv6 over IPv4 tunneling driver > NET: Registered protocol family 17 > NET: Registered protocol family 15 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> > All bugs added by David S. Miller <davem@redhat.com> > rtc-ds1307 0-0068: setting system clock to 2009-07-01 10:24:20 UTC (1246443860) > RAMDISK: Compressed image found at block 0 > VFS: Mounted root (ext2 filesystem) on device 1:0. > Freeing unused kernel memory: 216k init > Mounting /proc and /sys > Setting the hostname to P2020RDB > Mounting filesystems > mount: sysfs already mounted or /sys busy > mount: according to mtab, /sys is already mounted on /sys > Starting syslogd and klogd > Running sysctl > Setting up networking on loopback device: > Setting up networking on eth0: ADDRCONF(NETDEV_UP): eth0: link is not ready > > Adding static route for default gateway to 192.168.0.1: > Setting nameserver to 192.168.0.1 in /etc/resolv.conf: > SettingADDRCONF(NETDEV_UP): eth1: link is not ready > up networking on eth1: > Adding static route for default gateway to 192.168.1.1: > Setting nameserver to 192.168.1.1 in /etc/resolv.conf: > SettingADDRCONF(NETDEV_UP): eth2: link is not ready > up networking on eth2: > Adding static route for default gateway to 192.168.2.1: > Starting inetd: > Starting the port mapper: > Generating keys for the dropbear ssh server: > Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key' > Generating key, this may take a while... > Public key portion is: > ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwC8sk4V/7x6e0hJOjBdcGmUx26QQfpVdxT1z9itBPZf/bdfogKI5OHEfCPU2Tc+ZYNtrPXIgYvrML5I5z/WQL7QNgOx0/Vv > woNbxHLXj5UmirIJ6kNKlyUisPyZNU54XQjKCTpK7GjcGvUFgQMqv2HqWMfFV9XmytvXJgkhyg0jxox7 root@P2020RDB > Fingerprint: md5 2d:50:46:59:d1:92:72:1f:07:cf:e4:b6:14:6c:86:f3 > Starting the dropbear ssh server: > Starting the boa webserver: > Please set the system time using > date <mmddhhmnyyyy> > /sbin/hwclock -w > PHY: 0:01 - Link is Up - 1000/Full > ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > > > Welcome to Freescale Semiconductor Embedded Linux Environment > > !!!!! WARNING !!!!!!! > > The default password for the root account is: root > please change this password using the 'passwd' command > and then edit this message (/etc/issue) to remove this message > > P2020RDB login: PHY: mdio0@520:01 - Link is Up - 1000/Full > ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready > root > Password: > [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig eth0 down > [root@P2020RDB /root]# [root@P2020RDB /root]# ifconfig eth0 down\b\b\b\b\b\b down 1 down down > [root@P2020RDB /root]# [root@P2020RDB /root]# ifconfig eth1 down\b\b\b\b\b\b down 2 down down > [root@P2020RDB /root]# > [root@P2020RDB /root]# > [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig eth0 192.168.1.2 netmask 255.255.255.0 > [root@P2020RDB /root]# PHY: 0:01 - Link is Up - 1000/Full > > [root@P2020RDB /root]# ifcoe\b \b\b\b\b\b[root@P2020RDB /root]# ifconfig t\b \beyh\b \b\b \bth2 192.168.2.2 netmask 255.255.255.0 > [root@P2020RDB /root]# PHY: mdio0@520:01 - Link is Up - 1000/Full > > [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig eth\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \b\b \beccho 1 > /p\b\b[root@P2020RDB /root]# eccho 1 > /proc/sy[root@P2020RDB /root]# eccho 1 > /proc/sys/n[root@P2020RDB /root]# eccho 1 > /proc/sys/net/ip[root@P2020RDB /root]# eccho 1 > /proc/sys/net/ipv4[root@P2020RDB /root]# eccho 1 > /proc/sys/net/ipv4/ip_f[root@P2020RDB /root]# eccho 1 > /proc/sys/net/ipv4/ip_forward > -sh: eccho: not found > [root@P2020RDB /root]# echo 1 > /p\b\b[root@P2020RDB /root]# echo 1 > /proc/sy[root@P2020RDB /root]# echo 1 > /proc/sys/n[root@P2020RDB /root]# echo 1 > /proc/sys/net/ip[root@P2020RDB /root]# echo 1 > /proc/sys/net/ipv4[root@P2020RDB /root]# echo 1 > /proc/sys/net/ipv4/ip_f[root@P2020RDB /root]# echo 1 > /proc/sys/net/ipv4/ip_forward > [root@P2020RDB /root]# > [root@P2020RDB /root]# > [root@P2020RDB /root]# pn\b \bing 192.168.1.1 > PING 192.168.1.1 (192.168.1.1): 56 data bytes > 64 bytes from 192.168.1.1: seq=0 ttl=255 time=2.590 ms > 64 bytes from 192.168.1.1: seq=1 ttl=255 time=0.090 ms > > --- 192.168.1.1 ping statistics --- > 2 packets transmitted, 2 packets received, 0% packet loss > round-trip min/avg/max = 0.090/1.340/2.590 ms > [root@P2020RDB /root]# > [root@P2020RDB /root]# > [root@P2020RDB /root]# ping 192.168.2.1 > PING 192.168.2.1 (192.168.2.1): 56 data bytes > 64 bytes from 192.168.2.1: seq=0 ttl=255 time=3.502 ms > > --- 192.168.2.1 ping statistics --- > 1 packets transmitted, 1 packets received, 0% packet loss > round-trip min/avg/max = 3.502/3.502/3.502 ms > [root@P2020RDB /root]# arp > gateway2 (192.168.2.1) at 00:00:08:00:00:01 [ether] on eth2 > gateway1 (192.168.1.1) at 00:00:07:00:00:01 [ether] on eth0 > [root@P2020RDB /root]# arp -s 192.168.2.1 00:00:08:00:00:01 > [root@P2020RDB /root]# arp -s 192.1681.\b \b\b \b.1.1 00:00:07:00:00:01 > [root@P2020RDB /root]# > [root@P2020RDB /root]# > [root@P2020RDB /root]# > [root@P2020RDB /root]# arp > gateway2 (192.168.2.1) at 00:00:08:00:00:01 [ether] PERM on eth2 > gateway1 (192.168.1.1) at 00:00:07:00:00:01 [ether] PERM on eth0 > [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig > eth0 Link encap:Ethernet HWaddr 00:04:9F:0C:05:00 > inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:5 errors:0 dropped:0 overruns:0 frame:0 > TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:426 (426.0 B) TX bytes:1146 (1.1 KiB) > Base address:0x2000 > > eth2 Link encap:Ethernet HWaddr 00:04:9F:0C:05:02 > inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:4 errors:0 dropped:0 overruns:0 frame:0 > TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:318 (318.0 B) TX bytes:1048 (1.0 KiB) > Base address:0xa000 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > > [root@P2020RDB /root]# cat /p\b\b[root@P2020RDB /root]# cat /proc/in[root@P2020RDB /root]# cat /proc/interrupts > CPU0 CPU1 > 19: 648 0 OpenPIC Level fsl-elbc > 20: 0 0 OpenPIC Level fsldma-channel > 21: 0 0 OpenPIC Level fsldma-channel > 22: 0 0 OpenPIC Level fsldma-channel > 23: 0 0 OpenPIC Level fsldma-channel > 28: 0 0 OpenPIC Level ehci_hcd:usb1 > 29: 13 0 OpenPIC Level eth0_tx > 30: 0 4 OpenPIC Level eth0_rx > 31: 0 12 OpenPIC Level eth2_tx > 32: 4 0 OpenPIC Level eth2_rx > 33: 0 0 OpenPIC Level eth2_er > 34: 0 0 OpenPIC Level eth0_er > 42: 1049 0 OpenPIC Level serial > 43: 0 29 OpenPIC Level i2c-mpc, i2c-mpc > 45: 0 0 OpenPIC Level talitos > 59: 0 2494 OpenPIC Level fsl_espi > 72: 12 0 OpenPIC Level esdhc:slot0 > 76: 0 0 OpenPIC Level fsldma-channel > 77: 0 0 OpenPIC Level fsldma-channel > 78: 0 0 OpenPIC Level fsldma-channel > 79: 0 0 OpenPIC Level fsldma-channel > 251: 0 0 OpenPIC Edge ipi call function > 252: 1253 1387 OpenPIC Edge ipi reschedule > 253: 427 390 OpenPIC Edge ipi call function single > BAD: 1 > [root@P2020RDB /root]# PHY: mdio0@520:01 - Link is Down > PHY: mdio0@520:01 - Link is Up - 1000/Full > > [root@P2020RDB /root]# cat /p\b\b[root@P2020RDB /root]# cat /proc/in[root@P2020RDB /root]# cat /proc/interrupts > CPU0 CPU1 > 19: 648 0 OpenPIC Level fsl-elbc > 20: 0 0 OpenPIC Level fsldma-channel > 21: 0 0 OpenPIC Level fsldma-channel > 22: 0 0 OpenPIC Level fsldma-channel > 23: 0 0 OpenPIC Level fsldma-channel > 28: 0 0 OpenPIC Level ehci_hcd:usb1 > 29: 56328 0 OpenPIC Level eth0_tx > 30: 0 5553282 OpenPIC Level eth0_rx > 31: 0 43413 OpenPIC Level eth2_tx > 32: 5709572 0 OpenPIC Level eth2_rx > 33: 0 0 OpenPIC Level eth2_er > 34: 0 0 OpenPIC Level eth0_er > 42: 1179 0 OpenPIC Level serial > 43: 0 29 OpenPIC Level i2c-mpc, i2c-mpc > 45: 0 0 OpenPIC Level talitos > 59: 0 2494 OpenPIC Level fsl_espi > 72: 12 0 OpenPIC Level esdhc:slot0 > 76: 0 0 OpenPIC Level fsldma-channel > 77: 0 0 OpenPIC Level fsldma-channel > 78: 0 0 OpenPIC Level fsldma-channel > 79: 0 0 OpenPIC Level fsldma-channel > 251: 0 0 OpenPIC Edge ipi call function > 252: 1254 1389 OpenPIC Edge ipi reschedule > 253: 427 406 OpenPIC Edge ipi call function single > BAD: 36172 > [root@P2020RDB /root]# uname -a > Linux P2020RDB 2.6.29 #1 SMP Fri Jul 3 15:11:50 IST 2009 ppc unknown > [root@P2020RDB /root]# cat /p\b\b[root@P2020RDB /root]# cat /proc/in[root@P2020RDB /root]# cat /proc/interrupts > CPU0 CPU1 > 19: 648 0 OpenPIC Level fsl-elbc > 20: 0 0 OpenPIC Level fsldma-channel > 21: 0 0 OpenPIC Level fsldma-channel > 22: 0 0 OpenPIC Level fsldma-channel > 23: 0 0 OpenPIC Level fsldma-channel > 28: 0 0 OpenPIC Level ehci_hcd:usb1 > 29: 56328 0 OpenPIC Level eth0_tx > 30: 0 5553282 OpenPIC Level eth0_rx > 31: 0 43413 OpenPIC Level eth2_tx > 32: 5709572 0 OpenPIC Level eth2_rx > 33: 0 0 OpenPIC Level eth2_er > 34: 0 0 OpenPIC Level eth0_er > 42: 1329 0 OpenPIC Level serial > 43: 0 29 OpenPIC Level i2c-mpc, i2c-mpc > 45: 0 0 OpenPIC Level talitos > 59: 0 2494 OpenPIC Level fsl_espi > 72: 12 0 OpenPIC Level esdhc:slot0 > 76: 0 0 OpenPIC Level fsldma-channel > 77: 0 0 OpenPIC Level fsldma-channel > 78: 0 0 OpenPIC Level fsldma-channel > 79: 0 0 OpenPIC Level fsldma-channel > 251: 0 0 OpenPIC Edge ipi call function > 252: 1256 1391 OpenPIC Edge ipi reschedule > 253: 427 439 OpenPIC Edge ipi call function single > BAD: 36172 > [root@P2020RDB /root]# ifco\b\b\b\b[root@P2020RDB /root]# ifconfig > eth0 Link encap:Ethernet HWaddr 00:04:9F:0C:05:00 > inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:8928576 errors:0 dropped:0 overruns:0 frame:0 > TX packets:8928586 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:625000396 (596.0 MiB) TX bytes:535715406 (510.8 MiB) > Base address:0x2000 > > eth2 Link encap:Ethernet HWaddr 00:04:9F:0C:05:02 > inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:8928575 errors:0 dropped:0 overruns:0 frame:0 > TX packets:8928585 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:625000288 (596.0 MiB) TX bytes:535715308 (510.8 MiB) > Base address:0xa000 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > > [root@P2020RDB /root]# > ------------------------------------------------------------------------ > > _______________________________________________ > Linuxppc-dev mailing list > Linuxppc-dev@lists.ozlabs.org > https://lists.ozlabs.org/listinfo/linuxppc-dev -- Régis ODEYE Kontron Modular Computers SA 150, rue M. Berthelot / ZI Toulon Est / BP 244 / Fr 83078 TOULON Cedex 9 Phone: (33) 4 98 16 34 86 Fax: (33) 4 98 16 34 01 E-mail: regis.odeye@kontron.com Web : www.kontron.com ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2009-12-31 8:24 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2009-12-23 14:11 [HELP] BAD interrupts Kumar Gopalpet-B05799 2009-12-23 22:43 ` Michael Ellerman 2009-12-24 11:46 ` gshan 2009-12-24 10:45 ` Kumar Gopalpet-B05799 2009-12-31 8:12 ` Régis Odeyé
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).