From: Michael Neuling <mikey@neuling.org>
To: benh@kernel.crashing.org
Cc: Linux PPC dev <linuxppc-dev@ozlabs.org>,
Fengguang Wu <fengguang.wu@intel.com>
Subject: [PATCH] powerpc: rename set_break to avoid naming conflict
Date: Fri, 11 Jan 2013 11:25:34 +1100 [thread overview]
Message-ID: <12844.1357863934@ale.ozlabs.ibm.com> (raw)
In-Reply-To: <20130110105513.GA19224@localhost>
With allmodconfig we are getting:
drivers/tty/synclink_gt.c:160:12: error: conflicting types for 'set_break'
arch/powerpc/include/asm/debug.h:49:5: note: previous declaration of 'set_break' was here
drivers/tty/synclinkmp.c:526:12: error: conflicting types for 'set_break'
arch/powerpc/include/asm/debug.h:49:5: note: previous declaration of 'set_break' was here
This renames set_break to set_breakpoint to avoid this naming conflict
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
diff --git a/arch/powerpc/include/asm/debug.h b/arch/powerpc/include/asm/debug.h
index 8d85ffb..d251630 100644
--- a/arch/powerpc/include/asm/debug.h
+++ b/arch/powerpc/include/asm/debug.h
@@ -46,7 +46,7 @@ static inline int debugger_break_match(struct pt_regs *regs) { return 0; }
static inline int debugger_fault_handler(struct pt_regs *regs) { return 0; }
#endif
-int set_break(struct arch_hw_breakpoint *brk);
+int set_breakpoint(struct arch_hw_breakpoint *brk);
#ifdef CONFIG_PPC_ADV_DEBUG_REGS
extern void do_send_trap(struct pt_regs *regs, unsigned long address,
unsigned long error_code, int signal_code, int brkpt);
diff --git a/arch/powerpc/include/asm/hw_breakpoint.h b/arch/powerpc/include/asm/hw_breakpoint.h
index 2c91faf..96437e5 100644
--- a/arch/powerpc/include/asm/hw_breakpoint.h
+++ b/arch/powerpc/include/asm/hw_breakpoint.h
@@ -81,7 +81,7 @@ static inline void hw_breakpoint_disable(void)
brk.address = 0;
brk.type = 0;
brk.len = 0;
- set_break(&brk);
+ set_breakpoint(&brk);
}
extern void thread_change_pc(struct task_struct *tsk, struct pt_regs *regs);
diff --git a/arch/powerpc/kernel/hw_breakpoint.c b/arch/powerpc/kernel/hw_breakpoint.c
index c7483d0..2a3e8dd 100644
--- a/arch/powerpc/kernel/hw_breakpoint.c
+++ b/arch/powerpc/kernel/hw_breakpoint.c
@@ -73,7 +73,7 @@ int arch_install_hw_breakpoint(struct perf_event *bp)
* If so, DABR will be populated in single_step_dabr_instruction().
*/
if (current->thread.last_hit_ubp != bp)
- set_break(info);
+ set_breakpoint(info);
return 0;
}
@@ -191,7 +191,7 @@ void thread_change_pc(struct task_struct *tsk, struct pt_regs *regs)
info = counter_arch_bp(tsk->thread.last_hit_ubp);
regs->msr &= ~MSR_SE;
- set_break(info);
+ set_breakpoint(info);
tsk->thread.last_hit_ubp = NULL;
}
@@ -276,7 +276,7 @@ int __kprobes hw_breakpoint_handler(struct die_args *args)
if (!(info->type & HW_BRK_TYPE_EXTRANEOUS_IRQ))
perf_bp_event(bp, regs);
- set_break(info);
+ set_breakpoint(info);
out:
rcu_read_unlock();
return rc;
@@ -308,7 +308,7 @@ int __kprobes single_step_dabr_instruction(struct die_args *args)
if (!(info->type & HW_BRK_TYPE_EXTRANEOUS_IRQ))
perf_bp_event(bp, regs);
- set_break(info);
+ set_breakpoint(info);
current->thread.last_hit_ubp = NULL;
/*
diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c
index 8d56452..99550d3 100644
--- a/arch/powerpc/kernel/process.c
+++ b/arch/powerpc/kernel/process.c
@@ -366,7 +366,7 @@ static void set_debug_reg_defaults(struct thread_struct *thread)
{
thread->hw_brk.address = 0;
thread->hw_brk.type = 0;
- set_break(&thread->hw_brk);
+ set_breakpoint(&thread->hw_brk);
}
#endif /* !CONFIG_HAVE_HW_BREAKPOINT */
#endif /* CONFIG_PPC_ADV_DEBUG_REGS */
@@ -427,7 +427,7 @@ static inline int set_dawr(struct arch_hw_breakpoint *brk)
return 0;
}
-int set_break(struct arch_hw_breakpoint *brk)
+int set_breakpoint(struct arch_hw_breakpoint *brk)
{
__get_cpu_var(current_brk) = *brk;
@@ -538,7 +538,7 @@ struct task_struct *__switch_to(struct task_struct *prev,
*/
#ifndef CONFIG_HAVE_HW_BREAKPOINT
if (unlikely(hw_brk_match(&__get_cpu_var(current_brk), &new->thread.hw_brk)))
- set_break(&new->thread.hw_brk);
+ set_breakpoint(&new->thread.hw_brk);
#endif /* CONFIG_HAVE_HW_BREAKPOINT */
#endif
diff --git a/arch/powerpc/kernel/signal.c b/arch/powerpc/kernel/signal.c
index 1f26956..3003d89 100644
--- a/arch/powerpc/kernel/signal.c
+++ b/arch/powerpc/kernel/signal.c
@@ -132,7 +132,7 @@ static int do_signal(struct pt_regs *regs)
*/
if (current->thread.hw_brk.address &&
current->thread.hw_brk.type)
- set_break(¤t->thread.hw_brk);
+ set_breakpoint(¤t->thread.hw_brk);
#endif
/* Re-enable the breakpoints for the signal stack */
thread_change_pc(current, regs);
diff --git a/arch/powerpc/xmon/xmon.c b/arch/powerpc/xmon/xmon.c
index 529c1ed..13f85de 100644
--- a/arch/powerpc/xmon/xmon.c
+++ b/arch/powerpc/xmon/xmon.c
@@ -747,7 +747,7 @@ static void insert_cpu_bpts(void)
brk.address = dabr.address;
brk.type = (dabr.enabled & HW_BRK_TYPE_DABR) | HW_BRK_TYPE_PRIV_ALL;
brk.len = 8;
- set_break(&brk);
+ set_breakpoint(&brk);
}
if (iabr && cpu_has_feature(CPU_FTR_IABR))
mtspr(SPRN_IABR, iabr->address
prev parent reply other threads:[~2013-01-11 0:25 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <50ee8554.VPKmpSyDNCfRKVZL%yuanhan.liu@linux.intel.com>
2013-01-10 10:55 ` [powerpc:next 54/54] arch/powerpc/kernel/exceptions-64s.S:1204: Error: attempt to move .org backwards Fengguang Wu
2013-01-11 0:25 ` Michael Neuling [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=12844.1357863934@ale.ozlabs.ibm.com \
--to=mikey@neuling.org \
--cc=benh@kernel.crashing.org \
--cc=fengguang.wu@intel.com \
--cc=linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).