* [PATCH 1/5] powerpc: Move udbg_early_init() after early_init_devtree()
2011-01-26 21:51 [PATCH 0/5] powerpc: AMP support for 47x Dave Kleikamp
@ 2011-01-26 21:51 ` Dave Kleikamp
2011-01-26 21:51 ` [PATCH 2/5] powerpc/44x: allow override to hard-coded uart address Dave Kleikamp
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Dave Kleikamp @ 2011-01-26 21:51 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev, Dave Kleikamp
so that it can use information from the device tree.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
---
arch/powerpc/kernel/setup_32.c | 6 +++---
1 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/powerpc/kernel/setup_32.c b/arch/powerpc/kernel/setup_32.c
index 1d2fbc9..d1ca976 100644
--- a/arch/powerpc/kernel/setup_32.c
+++ b/arch/powerpc/kernel/setup_32.c
@@ -120,12 +120,12 @@ notrace void __init machine_init(unsigned long dt_ptr)
{
lockdep_init();
- /* Enable early debugging if any specified (see udbg.h) */
- udbg_early_init();
-
/* Do some early initialization based on the flat device tree */
early_init_devtree(__va(dt_ptr));
+ /* Enable early debugging if any specified (see udbg.h) */
+ udbg_early_init();
+
probe_machine();
setup_kdump_trampoline();
--
1.7.3.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 2/5] powerpc/44x: allow override to hard-coded uart address
2011-01-26 21:51 [PATCH 0/5] powerpc: AMP support for 47x Dave Kleikamp
2011-01-26 21:51 ` [PATCH 1/5] powerpc: Move udbg_early_init() after early_init_devtree() Dave Kleikamp
@ 2011-01-26 21:51 ` Dave Kleikamp
2011-01-26 21:51 ` [PATCH 3/5] powerpc/47x: allow kernel to be loaded in higher physical memory Dave Kleikamp
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Dave Kleikamp @ 2011-01-26 21:51 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev, Dave Kleikamp
Allow the early debug uart address to be overridden from the kernel
command line.
I would have preferred use the uart's virtual-reg property, but the device
tree hasn't been unflatted yet, and I don't know a reliable way to find it.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
---
arch/powerpc/kernel/udbg_16550.c | 17 ++++++++++++++---
1 files changed, 14 insertions(+), 3 deletions(-)
diff --git a/arch/powerpc/kernel/udbg_16550.c b/arch/powerpc/kernel/udbg_16550.c
index b4b167b..d36021a 100644
--- a/arch/powerpc/kernel/udbg_16550.c
+++ b/arch/powerpc/kernel/udbg_16550.c
@@ -219,6 +219,19 @@ void udbg_init_pas_realmode(void)
#ifdef CONFIG_PPC_EARLY_DEBUG_44x
#include <platforms/44x/44x.h>
+static unsigned long udbg_44x_comport = PPC44x_EARLY_DEBUG_VIRTADDR;
+
+static int __init early_parse_comport(char *p)
+{
+ if (!p || !(*p))
+ return 0;
+
+ udbg_44x_comport = simple_strtoul(p, 0, 16);
+
+ return 0;
+}
+early_param("uart_addr", early_parse_comport);
+
static void udbg_44x_as1_flush(void)
{
if (udbg_comport) {
@@ -249,9 +262,7 @@ static int udbg_44x_as1_getc(void)
void __init udbg_init_44x_as1(void)
{
- udbg_comport =
- (struct NS16550 __iomem *)PPC44x_EARLY_DEBUG_VIRTADDR;
-
+ udbg_comport = (struct NS16550 __iomem *)udbg_44x_comport;
udbg_putc = udbg_44x_as1_putc;
udbg_flush = udbg_44x_as1_flush;
udbg_getc = udbg_44x_as1_getc;
--
1.7.3.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 3/5] powerpc/47x: allow kernel to be loaded in higher physical memory
2011-01-26 21:51 [PATCH 0/5] powerpc: AMP support for 47x Dave Kleikamp
2011-01-26 21:51 ` [PATCH 1/5] powerpc: Move udbg_early_init() after early_init_devtree() Dave Kleikamp
2011-01-26 21:51 ` [PATCH 2/5] powerpc/44x: allow override to hard-coded uart address Dave Kleikamp
@ 2011-01-26 21:51 ` Dave Kleikamp
2011-01-26 21:51 ` [PATCH 4/5] powerpc/44x: don't use tlbivax on AMP systems Dave Kleikamp
2011-01-26 21:51 ` [PATCH 5/5] powerpc/476: Create a dts files for two 476 AMP instances under ISS Dave Kleikamp
4 siblings, 0 replies; 6+ messages in thread
From: Dave Kleikamp @ 2011-01-26 21:51 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev, Dave Kleikamp
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
---
arch/powerpc/Kconfig | 2 +-
arch/powerpc/configs/44x/iss476-smp_defconfig | 6 ++--
arch/powerpc/kernel/head_44x.S | 42 ++++++++++++++++++++-----
arch/powerpc/mm/44x_mmu.c | 13 ++++++--
4 files changed, 48 insertions(+), 15 deletions(-)
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 7d69e9b..fa41026 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -827,7 +827,7 @@ config LOWMEM_CAM_NUM
config RELOCATABLE
bool "Build a relocatable kernel (EXPERIMENTAL)"
- depends on EXPERIMENTAL && ADVANCED_OPTIONS && FLATMEM && FSL_BOOKE
+ depends on EXPERIMENTAL && ADVANCED_OPTIONS && FLATMEM && (FSL_BOOKE || PPC_47x)
help
This builds a kernel image that is capable of running at the
location the kernel is loaded at (some alignment restrictions may
diff --git a/arch/powerpc/configs/44x/iss476-smp_defconfig b/arch/powerpc/configs/44x/iss476-smp_defconfig
index 92f863a..a6eb6ad 100644
--- a/arch/powerpc/configs/44x/iss476-smp_defconfig
+++ b/arch/powerpc/configs/44x/iss476-smp_defconfig
@@ -3,8 +3,8 @@ CONFIG_SMP=y
CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_SPARSE_IRQ=y
CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_EXPERT=y
@@ -21,10 +21,11 @@ CONFIG_ISS4xx=y
CONFIG_HZ_100=y
CONFIG_MATH_EMULATION=y
CONFIG_IRQ_ALL_CPUS=y
-CONFIG_SPARSE_IRQ=y
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="root=/dev/issblk0"
# CONFIG_PCI is not set
+CONFIG_ADVANCED_OPTIONS=y
+CONFIG_RELOCATABLE=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
@@ -67,7 +68,6 @@ CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
-CONFIG_INOTIFY=y
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_CRAMFS=y
diff --git a/arch/powerpc/kernel/head_44x.S b/arch/powerpc/kernel/head_44x.S
index cbb3436..1da9b7e 100644
--- a/arch/powerpc/kernel/head_44x.S
+++ b/arch/powerpc/kernel/head_44x.S
@@ -93,6 +93,30 @@ _ENTRY(_start);
bl early_init
+#ifdef CONFIG_RELOCATABLE
+ /*
+ * r25 will contain RPN/ERPN for the start address of memory
+ *
+ * Add the difference between KERNELBASE and PAGE_OFFSET to the
+ * start of physical memory to get kernstart_addr.
+ */
+ lis r3,kernstart_addr@ha
+ la r3,kernstart_addr@l(r3)
+
+ lis r4,KERNELBASE@h
+ ori r4,r4,KERNELBASE@l
+ lis r5,PAGE_OFFSET@h
+ ori r5,r5,PAGE_OFFSET@l
+ subf r4,r5,r4
+
+ rlwinm r6,r25,0,28,31 /* ERPN */
+ rlwinm r7,r25,0,0,3 /* RPN - assuming 256 MB page size */
+ add r7,r7,r4
+
+ stw r6,0(r3)
+ stw r7,4(r3)
+#endif
+
/*
* Decide what sort of machine this is and initialize the MMU.
*/
@@ -1001,9 +1025,6 @@ clear_utlb_entry:
lis r3,PAGE_OFFSET@h
ori r3,r3,PAGE_OFFSET@l
- /* Kernel is at the base of RAM */
- li r4, 0 /* Load the kernel physical address */
-
/* Load the kernel PID = 0 */
li r0,0
mtspr SPRN_PID,r0
@@ -1013,9 +1034,8 @@ clear_utlb_entry:
clrrwi r3,r3,12 /* Mask off the effective page number */
ori r3,r3,PPC47x_TLB0_VALID | PPC47x_TLB0_256M
- /* Word 1 */
- clrrwi r4,r4,12 /* Mask off the real page number */
- /* ERPN is 0 for first 4GB page */
+ /* Word 1 - use r25. RPN is the same as the original entry */
+
/* Word 2 */
li r5,0
ori r5,r5,PPC47x_TLB2_S_RWX
@@ -1026,7 +1046,7 @@ clear_utlb_entry:
/* We write to way 0 and bolted 0 */
lis r0,0x8800
tlbwe r3,r0,0
- tlbwe r4,r0,1
+ tlbwe r25,r0,1
tlbwe r5,r0,2
/*
@@ -1124,7 +1144,13 @@ head_start_common:
lis r4,interrupt_base@h /* IVPR only uses the high 16-bits */
mtspr SPRN_IVPR,r4
- addis r22,r22,KERNELBASE@h
+ /*
+ * If the kernel was loaded at a non-zero 256 MB page, we need to
+ * mask off the most significant 4 bits to get the relative address
+ * from the start of physical memory
+ */
+ rlwinm r22,r22,0,4,31
+ addis r22,r22,PAGE_OFFSET@h
mtlr r22
isync
blr
diff --git a/arch/powerpc/mm/44x_mmu.c b/arch/powerpc/mm/44x_mmu.c
index 024acab..f60e006 100644
--- a/arch/powerpc/mm/44x_mmu.c
+++ b/arch/powerpc/mm/44x_mmu.c
@@ -186,10 +186,11 @@ void __init MMU_init_hw(void)
unsigned long __init mmu_mapin_ram(unsigned long top)
{
unsigned long addr;
+ unsigned long memstart = memstart_addr & ~(PPC_PIN_SIZE - 1);
/* Pin in enough TLBs to cover any lowmem not covered by the
* initial 256M mapping established in head_44x.S */
- for (addr = PPC_PIN_SIZE; addr < lowmem_end_addr;
+ for (addr = memstart + PPC_PIN_SIZE; addr < lowmem_end_addr;
addr += PPC_PIN_SIZE) {
if (mmu_has_feature(MMU_FTR_TYPE_47x))
ppc47x_pin_tlb(addr + PAGE_OFFSET, addr);
@@ -218,19 +219,25 @@ unsigned long __init mmu_mapin_ram(unsigned long top)
void setup_initial_memory_limit(phys_addr_t first_memblock_base,
phys_addr_t first_memblock_size)
{
+ u64 size;
+
+#ifndef CONFIG_RELOCATABLE
/* We don't currently support the first MEMBLOCK not mapping 0
* physical on those processors
*/
BUG_ON(first_memblock_base != 0);
+#endif
/* 44x has a 256M TLB entry pinned at boot */
- memblock_set_current_limit(min_t(u64, first_memblock_size, PPC_PIN_SIZE));
+ size = (min_t(u64, first_memblock_size, PPC_PIN_SIZE));
+ memblock_set_current_limit(first_memblock_base + size);
}
#ifdef CONFIG_SMP
void __cpuinit mmu_init_secondary(int cpu)
{
unsigned long addr;
+ unsigned long memstart = memstart_addr & ~(PPC_PIN_SIZE - 1);
/* Pin in enough TLBs to cover any lowmem not covered by the
* initial 256M mapping established in head_44x.S
@@ -241,7 +248,7 @@ void __cpuinit mmu_init_secondary(int cpu)
* stack. current (r2) isn't initialized, smp_processor_id()
* will not work, current thread info isn't accessible, ...
*/
- for (addr = PPC_PIN_SIZE; addr < lowmem_end_addr;
+ for (addr = memstart + PPC_PIN_SIZE; addr < lowmem_end_addr;
addr += PPC_PIN_SIZE) {
if (mmu_has_feature(MMU_FTR_TYPE_47x))
ppc47x_pin_tlb(addr + PAGE_OFFSET, addr);
--
1.7.3.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 4/5] powerpc/44x: don't use tlbivax on AMP systems
2011-01-26 21:51 [PATCH 0/5] powerpc: AMP support for 47x Dave Kleikamp
` (2 preceding siblings ...)
2011-01-26 21:51 ` [PATCH 3/5] powerpc/47x: allow kernel to be loaded in higher physical memory Dave Kleikamp
@ 2011-01-26 21:51 ` Dave Kleikamp
2011-01-26 21:51 ` [PATCH 5/5] powerpc/476: Create a dts files for two 476 AMP instances under ISS Dave Kleikamp
4 siblings, 0 replies; 6+ messages in thread
From: Dave Kleikamp @ 2011-01-26 21:51 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev, Dave Kleikamp
Since other OS's may be running on the other cores don't use tlbivax
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
---
arch/powerpc/include/asm/mmu.h | 2 +-
arch/powerpc/kernel/setup_32.c | 2 ++
arch/powerpc/mm/tlb_nohash.c | 21 ++++++++++++++++++++-
3 files changed, 23 insertions(+), 2 deletions(-)
diff --git a/arch/powerpc/include/asm/mmu.h b/arch/powerpc/include/asm/mmu.h
index bb40a06..f3a7c65 100644
--- a/arch/powerpc/include/asm/mmu.h
+++ b/arch/powerpc/include/asm/mmu.h
@@ -80,7 +80,7 @@ static inline int mmu_has_feature(unsigned long feature)
extern unsigned int __start___mmu_ftr_fixup, __stop___mmu_ftr_fixup;
-/* MMU initialization (64-bit only fo now) */
+/* MMU initialization */
extern void early_init_mmu(void);
extern void early_init_mmu_secondary(void);
diff --git a/arch/powerpc/kernel/setup_32.c b/arch/powerpc/kernel/setup_32.c
index d1ca976..e50ead7 100644
--- a/arch/powerpc/kernel/setup_32.c
+++ b/arch/powerpc/kernel/setup_32.c
@@ -126,6 +126,8 @@ notrace void __init machine_init(unsigned long dt_ptr)
/* Enable early debugging if any specified (see udbg.h) */
udbg_early_init();
+ early_init_mmu();
+
probe_machine();
setup_kdump_trampoline();
diff --git a/arch/powerpc/mm/tlb_nohash.c b/arch/powerpc/mm/tlb_nohash.c
index 2a030d8..b33c5e6 100644
--- a/arch/powerpc/mm/tlb_nohash.c
+++ b/arch/powerpc/mm/tlb_nohash.c
@@ -35,6 +35,7 @@
#include <linux/preempt.h>
#include <linux/spinlock.h>
#include <linux/memblock.h>
+#include <linux/of_fdt.h>
#include <asm/tlbflush.h>
#include <asm/tlb.h>
@@ -153,6 +154,17 @@ EXPORT_SYMBOL(local_flush_tlb_page);
*/
#ifdef CONFIG_SMP
+static int amp;
+
+#ifdef CONFIG_44x
+void __init early_init_mmu_44x(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+ if (of_flat_dt_is_compatible(root, "ibm,47x-AMP"))
+ amp = 1;
+}
+#endif /* CONFIG_44x */
+
static DEFINE_RAW_SPINLOCK(tlbivax_lock);
static int mm_is_core_local(struct mm_struct *mm)
@@ -232,7 +244,7 @@ void __flush_tlb_page(struct mm_struct *mm, unsigned long vmaddr,
cpu_mask = mm_cpumask(mm);
if (!mm_is_core_local(mm)) {
/* If broadcast tlbivax is supported, use it */
- if (mmu_has_feature(MMU_FTR_USE_TLBIVAX_BCAST)) {
+ if (!amp && mmu_has_feature(MMU_FTR_USE_TLBIVAX_BCAST)) {
int lock = mmu_has_feature(MMU_FTR_LOCK_BCAST_INVAL);
if (lock)
raw_spin_lock(&tlbivax_lock);
@@ -587,4 +599,11 @@ void setup_initial_memory_limit(phys_addr_t first_memblock_base,
/* Finally limit subsequent allocations */
memblock_set_current_limit(first_memblock_base + ppc64_rma_size);
}
+#else /* ! CONFIG_PPC64 */
+void __init early_init_mmu(void)
+{
+#if defined(CONFIG_SMP) && defined(CONFIG_44x)
+ early_init_mmu_44x();
+#endif
+}
#endif /* CONFIG_PPC64 */
--
1.7.3.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 5/5] powerpc/476: Create a dts files for two 476 AMP instances under ISS
2011-01-26 21:51 [PATCH 0/5] powerpc: AMP support for 47x Dave Kleikamp
` (3 preceding siblings ...)
2011-01-26 21:51 ` [PATCH 4/5] powerpc/44x: don't use tlbivax on AMP systems Dave Kleikamp
@ 2011-01-26 21:51 ` Dave Kleikamp
4 siblings, 0 replies; 6+ messages in thread
From: Dave Kleikamp @ 2011-01-26 21:51 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev, Dave Kleikamp
These are completely independent OS instances, each running on 2 cores.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
---
arch/powerpc/boot/Makefile | 9 ++-
arch/powerpc/boot/dts/iss476-amp1.dts | 119 ++++++++++++++++++++++++++++++
arch/powerpc/boot/dts/iss476-amp2.dts | 123 ++++++++++++++++++++++++++++++++
arch/powerpc/boot/treeboot-iss4xx-hi.c | 65 +++++++++++++++++
arch/powerpc/boot/wrapper | 7 ++
5 files changed, 321 insertions(+), 2 deletions(-)
create mode 100644 arch/powerpc/boot/dts/iss476-amp1.dts
create mode 100644 arch/powerpc/boot/dts/iss476-amp2.dts
create mode 100644 arch/powerpc/boot/treeboot-iss4xx-hi.c
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index 8917816..417502a 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -45,6 +45,8 @@ $(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=405
$(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405
$(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
$(obj)/treeboot-iss4xx.o: BOOTCFLAGS += -mcpu=405
+$(obj)/treeboot-iss476-amp1.o: BOOTCFLAGS += -mcpu=405
+$(obj)/treeboot-iss476-amp2.o: BOOTCFLAGS += -mcpu=405
$(obj)/virtex405-head.o: BOOTAFLAGS += -mcpu=405
@@ -78,7 +80,8 @@ src-plat := of.c cuboot-52xx.c cuboot-824x.c cuboot-83xx.c cuboot-85xx.c holly.c
cuboot-warp.c cuboot-85xx-cpm2.c cuboot-yosemite.c simpleboot.c \
virtex405-head.S virtex.c redboot-83xx.c cuboot-sam440ep.c \
cuboot-acadia.c cuboot-amigaone.c cuboot-kilauea.c \
- gamecube-head.S gamecube.c wii-head.S wii.c treeboot-iss4xx.c
+ gamecube-head.S gamecube.c wii-head.S wii.c treeboot-iss4xx.c \
+ treeboot-iss4xx-hi.c
src-boot := $(src-wlib) $(src-plat) empty.c
src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -208,7 +211,9 @@ image-$(CONFIG_KATMAI) += cuImage.katmai
image-$(CONFIG_WARP) += cuImage.warp
image-$(CONFIG_YOSEMITE) += cuImage.yosemite
image-$(CONFIG_ISS4xx) += treeImage.iss4xx \
- treeImage.iss4xx-mpic
+ treeImage.iss4xx-mpic \
+ treeImage.iss476-amp1 \
+ treeImage.iss476-amp2
# Board ports in arch/powerpc/platform/8xx/Kconfig
image-$(CONFIG_MPC86XADS) += cuImage.mpc866ads
diff --git a/arch/powerpc/boot/dts/iss476-amp1.dts b/arch/powerpc/boot/dts/iss476-amp1.dts
new file mode 100644
index 0000000..7de3485
--- /dev/null
+++ b/arch/powerpc/boot/dts/iss476-amp1.dts
@@ -0,0 +1,119 @@
+/*
+ * Device Tree Source for IBM Embedded PPC 476 Platform
+ *
+ * Copyright 2010 Torez Smith, IBM Corporation.
+ *
+ * Based on earlier code:
+ * Copyright (c) 2006, 2007 IBM Corp.
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>, David Gibson <dwg@au1.ibm.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/memreserve/ 0x01f00000 0x00100000;
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ model = "ibm,iss-4xx";
+ compatible = "ibm,iss-4xx", "ibm,47x-AMP";
+ dcr-parent = <&{/cpus/cpu@0}>;
+
+ aliases {
+ serial0 = &UART0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ model = "PowerPC,4xx"; // real CPU changed in sim
+ reg = <0>;
+ clock-frequency = <100000000>; // 100Mhz :-)
+ timebase-frequency = <100000000>;
+ i-cache-line-size = <32>;
+ d-cache-line-size = <32>;
+ i-cache-size = <32768>;
+ d-cache-size = <32768>;
+ dcr-controller;
+ dcr-access-method = "native";
+ status = "ok";
+ };
+ cpu@1 {
+ device_type = "cpu";
+ model = "PowerPC,4xx"; // real CPU changed in sim
+ reg = <1>;
+ clock-frequency = <100000000>; // 100Mhz :-)
+ timebase-frequency = <100000000>;
+ i-cache-line-size = <32>;
+ d-cache-line-size = <32>;
+ i-cache-size = <32768>;
+ d-cache-size = <32768>;
+ dcr-controller;
+ dcr-access-method = "native";
+ status = "disabled";
+ enable-method = "spin-table";
+ cpu-release-addr = <0 0x01f00100>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000>; // Filled in by zImage
+
+ };
+
+ MPIC: interrupt-controller {
+ compatible = "chrp,open-pic";
+ interrupt-controller;
+ dcr-reg = <0xffc00000 0x00030000>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+
+ };
+
+ plb {
+ compatible = "ibm,plb-4xx", "ibm,plb4"; /* Could be PLB6, doesn't matter */
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; // Filled in by zImage
+
+ POB0: opb {
+ compatible = "ibm,opb-4xx", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /* Wish there was a nicer way of specifying a full 32-bit
+ range */
+ ranges = <0x00000000 0x00000001 0x00000000 0x80000000
+ 0x80000000 0x00000001 0x80000000 0x80000000>;
+ clock-frequency = <0>; // Filled in by zImage
+ UART0: serial@40000200 {
+ device_type = "serial";
+ compatible = "ns16550a";
+ reg = <0x40000200 0x00000008>;
+ virtual-reg = <0xe0000200>;
+ clock-frequency = <11059200>;
+ current-speed = <115200>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <0x0 0x2>;
+ };
+ };
+ };
+
+ nvrtc {
+ compatible = "ds1743-nvram", "ds1743", "rtc-ds1743";
+ reg = <0 0xEF703000 0x2000>;
+ };
+
+ chosen {
+ linux,stdout-path = "/plb/opb/serial@40000200";
+ };
+};
diff --git a/arch/powerpc/boot/dts/iss476-amp2.dts b/arch/powerpc/boot/dts/iss476-amp2.dts
new file mode 100644
index 0000000..df38ee5
--- /dev/null
+++ b/arch/powerpc/boot/dts/iss476-amp2.dts
@@ -0,0 +1,123 @@
+/*
+ * Device Tree Source for IBM Embedded PPC 476 Platform
+ *
+ * Copyright 2010 Torez Smith, IBM Corporation.
+ *
+ * Based on earlier code:
+ * Copyright (c) 2006, 2007 IBM Corp.
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>, David Gibson <dwg@au1.ibm.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/memreserve/ 0x11f00000 0x00100000;
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ model = "ibm,iss-4xx";
+ compatible = "ibm,iss-4xx", "ibm,47x-AMP";
+ dcr-parent = <&{/cpus/cpu@2}>;
+
+ aliases {
+ serial0 = &UART0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@2 {
+ device_type = "cpu";
+ model = "PowerPC,4xx"; // real CPU changed in sim
+ reg = <2>;
+ clock-frequency = <100000000>; // 100Mhz :-)
+ timebase-frequency = <100000000>;
+ i-cache-line-size = <32>;
+ d-cache-line-size = <32>;
+ i-cache-size = <32768>;
+ d-cache-size = <32768>;
+ dcr-controller;
+ dcr-access-method = "native";
+ status = "ok";
+ };
+ cpu@3 {
+ device_type = "cpu";
+ model = "PowerPC,4xx"; // real CPU changed in sim
+ reg = <3>;
+ clock-frequency = <100000000>; // 100Mhz :-)
+ timebase-frequency = <100000000>;
+ i-cache-line-size = <32>;
+ d-cache-line-size = <32>;
+ i-cache-size = <32768>;
+ d-cache-size = <32768>;
+ dcr-controller;
+ dcr-access-method = "native";
+ status = "disabled";
+ enable-method = "spin-table";
+ cpu-release-addr = <0 0x11f00300>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+/*
+ reg = <0x00000000 0x00000000 0x00000000>; // Filled in by zImage
+ */
+ reg = < 0x0 0x10000000 0x02000000 >;
+
+ };
+
+ MPIC: interrupt-controller {
+ compatible = "chrp,open-pic";
+ interrupt-controller;
+ dcr-reg = <0xffc00000 0x00030000>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+
+ };
+
+ plb {
+ compatible = "ibm,plb-4xx", "ibm,plb4"; /* Could be PLB6, doesn't matter */
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; // Filled in by zImage
+
+ POB0: opb {
+ compatible = "ibm,opb-4xx", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /* Wish there was a nicer way of specifying a full 32-bit
+ range */
+ ranges = <0x00000000 0x00000001 0x00000000 0x80000000
+ 0x80000000 0x00000001 0x80000000 0x80000000>;
+ clock-frequency = <0>; // Filled in by zImage
+ UART0: serial@40001200 {
+ device_type = "serial";
+ compatible = "ns16550a";
+ reg = <0x40001200 0x00000008>;
+ virtual-reg = <0xe0001200>;
+ clock-frequency = <11059200>;
+ current-speed = <115200>;
+ interrupt-parent = <&MPIC>;
+ interrupts = <0x1 0x2>;
+ };
+ };
+ };
+
+ nvrtc {
+ compatible = "ds1743-nvram", "ds1743", "rtc-ds1743";
+ reg = <0 0xEF703000 0x2000>;
+ };
+
+ chosen {
+ bootargs = "uart_addr=0xf0001200";
+ linux,stdout-path = "/plb/opb/serial@40001200";
+ };
+};
diff --git a/arch/powerpc/boot/treeboot-iss4xx-hi.c b/arch/powerpc/boot/treeboot-iss4xx-hi.c
new file mode 100644
index 0000000..c6f376f
--- /dev/null
+++ b/arch/powerpc/boot/treeboot-iss4xx-hi.c
@@ -0,0 +1,65 @@
+/*
+ * Copyright 2010 Ben. Herrenschmidt, IBM Corporation.
+ *
+ * Based on earlier code:
+ * Copyright (C) Paul Mackerras 1997.
+ *
+ * Matt Porter <mporter@kernel.crashing.org>
+ * Copyright 2002-2005 MontaVista Software Inc.
+ *
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ * Copyright (c) 2003, 2004 Zultys Technologies
+ *
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <stdarg.h>
+#include <stddef.h>
+#include "types.h"
+#include "elf.h"
+#include "string.h"
+#include "stdio.h"
+#include "page.h"
+#include "ops.h"
+#include "reg.h"
+#include "io.h"
+#include "dcr.h"
+#include "4xx.h"
+#include "44x.h"
+#include "libfdt.h"
+
+BSS_STACK(4096);
+
+static void iss_4xx_fixups(void)
+{
+ ibm4xx_sdram_fixup_memsize();
+}
+
+/*
+ * Quick and dirty hack for loading a kernel at fixed address 0x10000000
+ */
+static void *iss_4xx_vmlinux_alloc(unsigned long size)
+{
+ return (void *)0x10000000;
+}
+
+#define SPRN_PIR 0x11E /* Processor Indentification Register */
+void platform_init(void)
+{
+ unsigned long end_of_ram = 0x08000000;
+ unsigned long avail_ram = end_of_ram - (unsigned long)_end;
+ u32 pir_reg;
+
+ simple_alloc_init(_end, avail_ram, 128, 64);
+ /* platform_ops.fixups = iss_4xx_fixups; */
+ platform_ops.vmlinux_alloc = iss_4xx_vmlinux_alloc;
+ platform_ops.exit = ibm44x_dbcr_reset;
+ pir_reg = mfspr(SPRN_PIR);
+ fdt_set_boot_cpuid_phys(_dtb_start, pir_reg);
+ fdt_init(_dtb_start);
+ serial_console_init();
+}
diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper
index cb97e75..2d2336c 100755
--- a/arch/powerpc/boot/wrapper
+++ b/arch/powerpc/boot/wrapper
@@ -244,6 +244,13 @@ gamecube|wii)
treeboot-iss4xx-mpic)
platformo="$object/treeboot-iss4xx.o"
;;
+treeboot-iss476-amp1)
+ platformo="$object/treeboot-iss4xx.o"
+ ;;
+treeboot-iss476-amp2)
+ platformo="$object/treeboot-iss4xx-hi.o"
+ link_address='0x10400000'
+ ;;
esac
vmz="$tmpdir/`basename \"$kernel\"`.$ext"
--
1.7.3.4
^ permalink raw reply related [flat|nested] 6+ messages in thread