* [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit
@ 2011-11-12 12:02 Liu Gang
2011-11-12 12:02 ` [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message units support Liu Gang
` (4 more replies)
0 siblings, 5 replies; 18+ messages in thread
From: Liu Gang @ 2011-11-12 12:02 UTC (permalink / raw)
To: linuxppc-dev, Alexandre.Bounine
Cc: r58472, r61911, linux-kernel, Lian Minghuan, Liu Gang, akpm,
B11780
The Freescale PowerPC RapidIO controller consists of a RapidIO endpoint and
a RapidIO message unit(RMU). Or use RapidIO message manager(RMan) to
replace the RMU in DPAA architecture. Therefore, we should split the code
into two function modules according to the hardware architecture. Add new
struct for RMU module, and new initialization function to set up RMU
module. This policy is very conducive to adding new module like RMan, or
adding multi-ports or message units support.
Signed-off-by: Lian Minghuan <Minghuan.Lian@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/sysdev/Makefile | 2 +-
arch/powerpc/sysdev/fsl_rio.c | 1152 +---------------------------------------
arch/powerpc/sysdev/fsl_rio.h | 78 +++
arch/powerpc/sysdev/fsl_rmu.c | 1163 +++++++++++++++++++++++++++++++++++++++++
4 files changed, 1267 insertions(+), 1128 deletions(-)
create mode 100644 arch/powerpc/sysdev/fsl_rio.h
create mode 100644 arch/powerpc/sysdev/fsl_rmu.c
diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile
index 84e1325..8dea593 100644
--- a/arch/powerpc/sysdev/Makefile
+++ b/arch/powerpc/sysdev/Makefile
@@ -20,7 +20,7 @@ obj-$(CONFIG_FSL_LBC) += fsl_lbc.o
obj-$(CONFIG_FSL_GTM) += fsl_gtm.o
obj-$(CONFIG_FSL_85XX_CACHE_SRAM) += fsl_85xx_l2ctlr.o fsl_85xx_cache_sram.o
obj-$(CONFIG_SIMPLE_GPIO) += simple_gpio.o
-obj-$(CONFIG_FSL_RIO) += fsl_rio.o
+obj-$(CONFIG_FSL_RIO) += fsl_rio.o fsl_rmu.o
obj-$(CONFIG_TSI108_BRIDGE) += tsi108_pci.o tsi108_dev.o
obj-$(CONFIG_QUICC_ENGINE) += qe_lib/
obj-$(CONFIG_PPC_BESTCOMM) += bestcomm/
diff --git a/arch/powerpc/sysdev/fsl_rio.c b/arch/powerpc/sysdev/fsl_rio.c
index 22ffccd..9484484 100644
--- a/arch/powerpc/sysdev/fsl_rio.c
+++ b/arch/powerpc/sysdev/fsl_rio.c
@@ -10,7 +10,7 @@
* - Added Port-Write message handling
* - Added Machine Check exception handling
*
- * Copyright (C) 2007, 2008, 2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2007, 2008, 2010, 2011 Freescale Semiconductor, Inc.
* Zhang Wei <wei.zhang@freescale.com>
*
* Copyright 2005 MontaVista Software, Inc.
@@ -28,240 +28,34 @@
#include <linux/dma-mapping.h>
#include <linux/interrupt.h>
#include <linux/device.h>
-#include <linux/rio.h>
-#include <linux/rio_drv.h>
#include <linux/of_platform.h>
#include <linux/delay.h>
#include <linux/slab.h>
-#include <linux/kfifo.h>
-#include <asm/io.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
#include <asm/machdep.h>
-#include <asm/uaccess.h>
-#undef DEBUG_PW /* Port-Write debugging */
+#include "fsl_rio.h"
-/* RapidIO definition irq, which read from OF-tree */
-#define IRQ_RIO_BELL(m) (((struct rio_priv *)(m->priv))->bellirq)
-#define IRQ_RIO_TX(m) (((struct rio_priv *)(m->priv))->txirq)
-#define IRQ_RIO_RX(m) (((struct rio_priv *)(m->priv))->rxirq)
-#define IRQ_RIO_PW(m) (((struct rio_priv *)(m->priv))->pwirq)
-
-#define IPWSR_CLEAR 0x98
-#define OMSR_CLEAR 0x1cb3
-#define IMSR_CLEAR 0x491
-#define IDSR_CLEAR 0x91
-#define ODSR_CLEAR 0x1c00
-#define LTLEECSR_ENABLE_ALL 0xFFC000FC
-#define ESCSR_CLEAR 0x07120204
-#define IECSR_CLEAR 0x80000000
+#undef DEBUG_PW /* Port-Write debugging */
#define RIO_PORT1_EDCSR 0x0640
#define RIO_PORT2_EDCSR 0x0680
#define RIO_PORT1_IECSR 0x10130
#define RIO_PORT2_IECSR 0x101B0
-#define RIO_IM0SR 0x13064
-#define RIO_IM1SR 0x13164
-#define RIO_OM0SR 0x13004
-#define RIO_OM1SR 0x13104
#define RIO_ATMU_REGS_OFFSET 0x10c00
-#define RIO_P_MSG_REGS_OFFSET 0x11000
-#define RIO_S_MSG_REGS_OFFSET 0x13000
#define RIO_GCCSR 0x13c
#define RIO_ESCSR 0x158
+#define ESCSR_CLEAR 0x07120204
#define RIO_PORT2_ESCSR 0x178
#define RIO_CCSR 0x15c
-#define RIO_LTLEDCSR 0x0608
#define RIO_LTLEDCSR_IER 0x80000000
#define RIO_LTLEDCSR_PRT 0x01000000
-#define RIO_LTLEECSR 0x060c
-#define RIO_EPWISR 0x10010
+#define IECSR_CLEAR 0x80000000
#define RIO_ISR_AACR 0x10120
#define RIO_ISR_AACR_AA 0x1 /* Accept All ID */
-#define RIO_MAINT_WIN_SIZE 0x400000
-#define RIO_DBELL_WIN_SIZE 0x1000
-
-#define RIO_MSG_OMR_MUI 0x00000002
-#define RIO_MSG_OSR_TE 0x00000080
-#define RIO_MSG_OSR_QOI 0x00000020
-#define RIO_MSG_OSR_QFI 0x00000010
-#define RIO_MSG_OSR_MUB 0x00000004
-#define RIO_MSG_OSR_EOMI 0x00000002
-#define RIO_MSG_OSR_QEI 0x00000001
-
-#define RIO_MSG_IMR_MI 0x00000002
-#define RIO_MSG_ISR_TE 0x00000080
-#define RIO_MSG_ISR_QFI 0x00000010
-#define RIO_MSG_ISR_DIQI 0x00000001
-
-#define RIO_IPWMR_SEN 0x00100000
-#define RIO_IPWMR_QFIE 0x00000100
-#define RIO_IPWMR_EIE 0x00000020
-#define RIO_IPWMR_CQ 0x00000002
-#define RIO_IPWMR_PWE 0x00000001
-
-#define RIO_IPWSR_QF 0x00100000
-#define RIO_IPWSR_TE 0x00000080
-#define RIO_IPWSR_QFI 0x00000010
-#define RIO_IPWSR_PWD 0x00000008
-#define RIO_IPWSR_PWB 0x00000004
-
-/* EPWISR Error match value */
-#define RIO_EPWISR_PINT1 0x80000000
-#define RIO_EPWISR_PINT2 0x40000000
-#define RIO_EPWISR_MU 0x00000002
-#define RIO_EPWISR_PW 0x00000001
-
-#define RIO_MSG_DESC_SIZE 32
-#define RIO_MSG_BUFFER_SIZE 4096
-#define RIO_MIN_TX_RING_SIZE 2
-#define RIO_MAX_TX_RING_SIZE 2048
-#define RIO_MIN_RX_RING_SIZE 2
-#define RIO_MAX_RX_RING_SIZE 2048
-
-#define DOORBELL_DMR_DI 0x00000002
-#define DOORBELL_DSR_TE 0x00000080
-#define DOORBELL_DSR_QFI 0x00000010
-#define DOORBELL_DSR_DIQI 0x00000001
-#define DOORBELL_TID_OFFSET 0x02
-#define DOORBELL_SID_OFFSET 0x04
-#define DOORBELL_INFO_OFFSET 0x06
-
-#define DOORBELL_MESSAGE_SIZE 0x08
-#define DBELL_SID(x) (*(u16 *)(x + DOORBELL_SID_OFFSET))
-#define DBELL_TID(x) (*(u16 *)(x + DOORBELL_TID_OFFSET))
-#define DBELL_INF(x) (*(u16 *)(x + DOORBELL_INFO_OFFSET))
-
-struct rio_atmu_regs {
- u32 rowtar;
- u32 rowtear;
- u32 rowbar;
- u32 pad2;
- u32 rowar;
- u32 pad3[3];
-};
-
-struct rio_msg_regs {
- u32 omr; /* 0xD_3000 - Outbound message 0 mode register */
- u32 osr; /* 0xD_3004 - Outbound message 0 status register */
- u32 pad1;
- u32 odqdpar; /* 0xD_300C - Outbound message 0 descriptor queue
- dequeue pointer address register */
- u32 pad2;
- u32 osar; /* 0xD_3014 - Outbound message 0 source address
- register */
- u32 odpr; /* 0xD_3018 - Outbound message 0 destination port
- register */
- u32 odatr; /* 0xD_301C - Outbound message 0 destination attributes
- Register*/
- u32 odcr; /* 0xD_3020 - Outbound message 0 double-word count
- register */
- u32 pad3;
- u32 odqepar; /* 0xD_3028 - Outbound message 0 descriptor queue
- enqueue pointer address register */
- u32 pad4[13];
- u32 imr; /* 0xD_3060 - Inbound message 0 mode register */
- u32 isr; /* 0xD_3064 - Inbound message 0 status register */
- u32 pad5;
- u32 ifqdpar; /* 0xD_306C - Inbound message 0 frame queue dequeue
- pointer address register*/
- u32 pad6;
- u32 ifqepar; /* 0xD_3074 - Inbound message 0 frame queue enqueue
- pointer address register */
- u32 pad7[226];
- u32 odmr; /* 0xD_3400 - Outbound doorbell mode register */
- u32 odsr; /* 0xD_3404 - Outbound doorbell status register */
- u32 res0[4];
- u32 oddpr; /* 0xD_3418 - Outbound doorbell destination port
- register */
- u32 oddatr; /* 0xD_341c - Outbound doorbell destination attributes
- register */
- u32 res1[3];
- u32 odretcr; /* 0xD_342C - Outbound doorbell retry error threshold
- configuration register */
- u32 res2[12];
- u32 dmr; /* 0xD_3460 - Inbound doorbell mode register */
- u32 dsr; /* 0xD_3464 - Inbound doorbell status register */
- u32 pad8;
- u32 dqdpar; /* 0xD_346C - Inbound doorbell queue dequeue Pointer
- address register */
- u32 pad9;
- u32 dqepar; /* 0xD_3474 - Inbound doorbell Queue enqueue pointer
- address register */
- u32 pad10[26];
- u32 pwmr; /* 0xD_34E0 - Inbound port-write mode register */
- u32 pwsr; /* 0xD_34E4 - Inbound port-write status register */
- u32 epwqbar; /* 0xD_34E8 - Extended Port-Write Queue Base Address
- register */
- u32 pwqbar; /* 0xD_34EC - Inbound port-write queue base address
- register */
-};
-
-struct rio_tx_desc {
- u32 res1;
- u32 saddr;
- u32 dport;
- u32 dattr;
- u32 res2;
- u32 res3;
- u32 dwcnt;
- u32 res4;
-};
-
-struct rio_dbell_ring {
- void *virt;
- dma_addr_t phys;
-};
-
-struct rio_msg_tx_ring {
- void *virt;
- dma_addr_t phys;
- void *virt_buffer[RIO_MAX_TX_RING_SIZE];
- dma_addr_t phys_buffer[RIO_MAX_TX_RING_SIZE];
- int tx_slot;
- int size;
- void *dev_id;
-};
-
-struct rio_msg_rx_ring {
- void *virt;
- dma_addr_t phys;
- void *virt_buffer[RIO_MAX_RX_RING_SIZE];
- int rx_slot;
- int size;
- void *dev_id;
-};
-
-struct rio_port_write_msg {
- void *virt;
- dma_addr_t phys;
- u32 msg_count;
- u32 err_count;
- u32 discard_count;
-};
-
-struct rio_priv {
- struct device *dev;
- void __iomem *regs_win;
- struct rio_atmu_regs __iomem *atmu_regs;
- struct rio_atmu_regs __iomem *maint_atmu_regs;
- struct rio_atmu_regs __iomem *dbell_atmu_regs;
- void __iomem *dbell_win;
- void __iomem *maint_win;
- struct rio_msg_regs __iomem *msg_regs;
- struct rio_dbell_ring dbell_ring;
- struct rio_msg_tx_ring msg_tx_ring;
- struct rio_msg_rx_ring msg_rx_ring;
- struct rio_port_write_msg port_write_msg;
- int bellirq;
- int txirq;
- int rxirq;
- int pwirq;
- struct work_struct pw_work;
- struct kfifo pw_fifo;
- spinlock_t pw_fifo_lock;
-};
#define __fsl_read_rio_config(x, addr, err, op) \
__asm__ __volatile__( \
@@ -279,7 +73,7 @@ struct rio_priv {
: "=r" (err), "=r" (x) \
: "b" (addr), "i" (-EFAULT), "0" (err))
-static void __iomem *rio_regs_win;
+void __iomem *rio_regs_win;
#ifdef CONFIG_E500
int fsl_rio_mcheck_exception(struct pt_regs *regs)
@@ -311,42 +105,6 @@ EXPORT_SYMBOL_GPL(fsl_rio_mcheck_exception);
#endif
/**
- * fsl_rio_doorbell_send - Send a MPC85xx doorbell message
- * @mport: RapidIO master port info
- * @index: ID of RapidIO interface
- * @destid: Destination ID of target device
- * @data: 16-bit info field of RapidIO doorbell message
- *
- * Sends a MPC85xx doorbell message. Returns %0 on success or
- * %-EINVAL on failure.
- */
-static int fsl_rio_doorbell_send(struct rio_mport *mport,
- int index, u16 destid, u16 data)
-{
- struct rio_priv *priv = mport->priv;
- pr_debug("fsl_doorbell_send: index %d destid %4.4x data %4.4x\n",
- index, destid, data);
- switch (mport->phy_type) {
- case RIO_PHY_PARALLEL:
- out_be32(&priv->dbell_atmu_regs->rowtar, destid << 22);
- out_be16(priv->dbell_win, data);
- break;
- case RIO_PHY_SERIAL:
- /* In the serial version silicons, such as MPC8548, MPC8641,
- * below operations is must be.
- */
- out_be32(&priv->msg_regs->odmr, 0x00000000);
- out_be32(&priv->msg_regs->odretcr, 0x00000004);
- out_be32(&priv->msg_regs->oddpr, destid << 16);
- out_be32(&priv->msg_regs->oddatr, data);
- out_be32(&priv->msg_regs->odmr, 0x00000001);
- break;
- }
-
- return 0;
-}
-
-/**
* fsl_local_config_read - Generate a MPC85xx local config space read
* @mport: RapidIO master port info
* @index: ID of RapdiIO interface
@@ -362,7 +120,7 @@ static int fsl_local_config_read(struct rio_mport *mport,
{
struct rio_priv *priv = mport->priv;
pr_debug("fsl_local_config_read: index %d offset %8.8x\n", index,
- offset);
+ offset);
*data = in_be32(priv->regs_win + offset);
return 0;
@@ -384,8 +142,8 @@ static int fsl_local_config_write(struct rio_mport *mport,
{
struct rio_priv *priv = mport->priv;
pr_debug
- ("fsl_local_config_write: index %d offset %8.8x data %8.8x\n",
- index, offset, data);
+ ("fsl_local_config_write: index %d offset %8.8x data %8.8x\n",
+ index, offset, data);
out_be32(priv->regs_win + offset, data);
return 0;
@@ -413,7 +171,8 @@ fsl_rio_config_read(struct rio_mport *mport, int index, u16 destid,
u32 rval, err = 0;
pr_debug
- ("fsl_rio_config_read: index %d destid %d hopcount %d offset %8.8x len %d\n",
+ ("fsl_rio_config_read:"
+ " index %d destid %d hopcount %d offset %8.8x len %d\n",
index, destid, hopcount, offset, len);
/* 16MB maintenance window possible */
@@ -423,7 +182,7 @@ fsl_rio_config_read(struct rio_mport *mport, int index, u16 destid,
out_be32(&priv->maint_atmu_regs->rowtar,
(destid << 22) | (hopcount << 12) | (offset >> 12));
- out_be32(&priv->maint_atmu_regs->rowtear, (destid >> 10));
+ out_be32(&priv->maint_atmu_regs->rowtear, (destid >> 10));
data = (u8 *) priv->maint_win + (offset & (RIO_MAINT_WIN_SIZE - 1));
switch (len) {
@@ -470,7 +229,8 @@ fsl_rio_config_write(struct rio_mport *mport, int index, u16 destid,
struct rio_priv *priv = mport->priv;
u8 *data;
pr_debug
- ("fsl_rio_config_write: index %d destid %d hopcount %d offset %8.8x len %d val %8.8x\n",
+ ("fsl_rio_config_write:"
+ "index %d destid %d hopcount %d offset %8.8x len %d val %8.8x\n",
index, destid, hopcount, offset, len, val);
/* 16MB maintenance windows possible */
@@ -480,7 +240,7 @@ fsl_rio_config_write(struct rio_mport *mport, int index, u16 destid,
out_be32(&priv->maint_atmu_regs->rowtar,
(destid << 22) | (hopcount << 12) | (offset >> 12));
- out_be32(&priv->maint_atmu_regs->rowtear, (destid >> 10));
+ out_be32(&priv->maint_atmu_regs->rowtear, (destid >> 10));
data = (u8 *) priv->maint_win + (offset & (RIO_MAINT_WIN_SIZE - 1));
switch (len) {
@@ -500,590 +260,7 @@ fsl_rio_config_write(struct rio_mport *mport, int index, u16 destid,
return 0;
}
-/**
- * fsl_add_outb_message - Add message to the MPC85xx outbound message queue
- * @mport: Master port with outbound message queue
- * @rdev: Target of outbound message
- * @mbox: Outbound mailbox
- * @buffer: Message to add to outbound queue
- * @len: Length of message
- *
- * Adds the @buffer message to the MPC85xx outbound message queue. Returns
- * %0 on success or %-EINVAL on failure.
- */
-static int
-fsl_add_outb_message(struct rio_mport *mport, struct rio_dev *rdev, int mbox,
- void *buffer, size_t len)
-{
- struct rio_priv *priv = mport->priv;
- u32 omr;
- struct rio_tx_desc *desc = (struct rio_tx_desc *)priv->msg_tx_ring.virt
- + priv->msg_tx_ring.tx_slot;
- int ret = 0;
-
- pr_debug("RIO: fsl_add_outb_message(): destid %4.4x mbox %d buffer " \
- "%8.8x len %8.8x\n", rdev->destid, mbox, (int)buffer, len);
-
- if ((len < 8) || (len > RIO_MAX_MSG_SIZE)) {
- ret = -EINVAL;
- goto out;
- }
-
- /* Copy and clear rest of buffer */
- memcpy(priv->msg_tx_ring.virt_buffer[priv->msg_tx_ring.tx_slot], buffer,
- len);
- if (len < (RIO_MAX_MSG_SIZE - 4))
- memset(priv->msg_tx_ring.virt_buffer[priv->msg_tx_ring.tx_slot]
- + len, 0, RIO_MAX_MSG_SIZE - len);
-
- switch (mport->phy_type) {
- case RIO_PHY_PARALLEL:
- /* Set mbox field for message */
- desc->dport = mbox & 0x3;
-
- /* Enable EOMI interrupt, set priority, and set destid */
- desc->dattr = 0x28000000 | (rdev->destid << 2);
- break;
- case RIO_PHY_SERIAL:
- /* Set mbox field for message, and set destid */
- desc->dport = (rdev->destid << 16) | (mbox & 0x3);
-
- /* Enable EOMI interrupt and priority */
- desc->dattr = 0x28000000;
- break;
- }
-
- /* Set transfer size aligned to next power of 2 (in double words) */
- desc->dwcnt = is_power_of_2(len) ? len : 1 << get_bitmask_order(len);
-
- /* Set snooping and source buffer address */
- desc->saddr = 0x00000004
- | priv->msg_tx_ring.phys_buffer[priv->msg_tx_ring.tx_slot];
-
- /* Increment enqueue pointer */
- omr = in_be32(&priv->msg_regs->omr);
- out_be32(&priv->msg_regs->omr, omr | RIO_MSG_OMR_MUI);
-
- /* Go to next descriptor */
- if (++priv->msg_tx_ring.tx_slot == priv->msg_tx_ring.size)
- priv->msg_tx_ring.tx_slot = 0;
-
- out:
- return ret;
-}
-
-/**
- * fsl_rio_tx_handler - MPC85xx outbound message interrupt handler
- * @irq: Linux interrupt number
- * @dev_instance: Pointer to interrupt-specific data
- *
- * Handles outbound message interrupts. Executes a register outbound
- * mailbox event handler and acks the interrupt occurrence.
- */
-static irqreturn_t
-fsl_rio_tx_handler(int irq, void *dev_instance)
-{
- int osr;
- struct rio_mport *port = (struct rio_mport *)dev_instance;
- struct rio_priv *priv = port->priv;
-
- osr = in_be32(&priv->msg_regs->osr);
-
- if (osr & RIO_MSG_OSR_TE) {
- pr_info("RIO: outbound message transmission error\n");
- out_be32(&priv->msg_regs->osr, RIO_MSG_OSR_TE);
- goto out;
- }
-
- if (osr & RIO_MSG_OSR_QOI) {
- pr_info("RIO: outbound message queue overflow\n");
- out_be32(&priv->msg_regs->osr, RIO_MSG_OSR_QOI);
- goto out;
- }
-
- if (osr & RIO_MSG_OSR_EOMI) {
- u32 dqp = in_be32(&priv->msg_regs->odqdpar);
- int slot = (dqp - priv->msg_tx_ring.phys) >> 5;
- port->outb_msg[0].mcback(port, priv->msg_tx_ring.dev_id, -1,
- slot);
-
- /* Ack the end-of-message interrupt */
- out_be32(&priv->msg_regs->osr, RIO_MSG_OSR_EOMI);
- }
-
- out:
- return IRQ_HANDLED;
-}
-
-/**
- * fsl_open_outb_mbox - Initialize MPC85xx outbound mailbox
- * @mport: Master port implementing the outbound message unit
- * @dev_id: Device specific pointer to pass on event
- * @mbox: Mailbox to open
- * @entries: Number of entries in the outbound mailbox ring
- *
- * Initializes buffer ring, request the outbound message interrupt,
- * and enables the outbound message unit. Returns %0 on success and
- * %-EINVAL or %-ENOMEM on failure.
- */
-static int
-fsl_open_outb_mbox(struct rio_mport *mport, void *dev_id, int mbox, int entries)
-{
- int i, j, rc = 0;
- struct rio_priv *priv = mport->priv;
-
- if ((entries < RIO_MIN_TX_RING_SIZE) ||
- (entries > RIO_MAX_TX_RING_SIZE) || (!is_power_of_2(entries))) {
- rc = -EINVAL;
- goto out;
- }
-
- /* Initialize shadow copy ring */
- priv->msg_tx_ring.dev_id = dev_id;
- priv->msg_tx_ring.size = entries;
-
- for (i = 0; i < priv->msg_tx_ring.size; i++) {
- priv->msg_tx_ring.virt_buffer[i] =
- dma_alloc_coherent(priv->dev, RIO_MSG_BUFFER_SIZE,
- &priv->msg_tx_ring.phys_buffer[i], GFP_KERNEL);
- if (!priv->msg_tx_ring.virt_buffer[i]) {
- rc = -ENOMEM;
- for (j = 0; j < priv->msg_tx_ring.size; j++)
- if (priv->msg_tx_ring.virt_buffer[j])
- dma_free_coherent(priv->dev,
- RIO_MSG_BUFFER_SIZE,
- priv->msg_tx_ring.
- virt_buffer[j],
- priv->msg_tx_ring.
- phys_buffer[j]);
- goto out;
- }
- }
-
- /* Initialize outbound message descriptor ring */
- priv->msg_tx_ring.virt = dma_alloc_coherent(priv->dev,
- priv->msg_tx_ring.size * RIO_MSG_DESC_SIZE,
- &priv->msg_tx_ring.phys, GFP_KERNEL);
- if (!priv->msg_tx_ring.virt) {
- rc = -ENOMEM;
- goto out_dma;
- }
- memset(priv->msg_tx_ring.virt, 0,
- priv->msg_tx_ring.size * RIO_MSG_DESC_SIZE);
- priv->msg_tx_ring.tx_slot = 0;
-
- /* Point dequeue/enqueue pointers at first entry in ring */
- out_be32(&priv->msg_regs->odqdpar, priv->msg_tx_ring.phys);
- out_be32(&priv->msg_regs->odqepar, priv->msg_tx_ring.phys);
-
- /* Configure for snooping */
- out_be32(&priv->msg_regs->osar, 0x00000004);
-
- /* Clear interrupt status */
- out_be32(&priv->msg_regs->osr, 0x000000b3);
-
- /* Hook up outbound message handler */
- rc = request_irq(IRQ_RIO_TX(mport), fsl_rio_tx_handler, 0,
- "msg_tx", (void *)mport);
- if (rc < 0)
- goto out_irq;
-
- /*
- * Configure outbound message unit
- * Snooping
- * Interrupts (all enabled, except QEIE)
- * Chaining mode
- * Disable
- */
- out_be32(&priv->msg_regs->omr, 0x00100220);
-
- /* Set number of entries */
- out_be32(&priv->msg_regs->omr,
- in_be32(&priv->msg_regs->omr) |
- ((get_bitmask_order(entries) - 2) << 12));
-
- /* Now enable the unit */
- out_be32(&priv->msg_regs->omr, in_be32(&priv->msg_regs->omr) | 0x1);
-
- out:
- return rc;
-
- out_irq:
- dma_free_coherent(priv->dev,
- priv->msg_tx_ring.size * RIO_MSG_DESC_SIZE,
- priv->msg_tx_ring.virt, priv->msg_tx_ring.phys);
-
- out_dma:
- for (i = 0; i < priv->msg_tx_ring.size; i++)
- dma_free_coherent(priv->dev, RIO_MSG_BUFFER_SIZE,
- priv->msg_tx_ring.virt_buffer[i],
- priv->msg_tx_ring.phys_buffer[i]);
-
- return rc;
-}
-
-/**
- * fsl_close_outb_mbox - Shut down MPC85xx outbound mailbox
- * @mport: Master port implementing the outbound message unit
- * @mbox: Mailbox to close
- *
- * Disables the outbound message unit, free all buffers, and
- * frees the outbound message interrupt.
- */
-static void fsl_close_outb_mbox(struct rio_mport *mport, int mbox)
-{
- struct rio_priv *priv = mport->priv;
- /* Disable inbound message unit */
- out_be32(&priv->msg_regs->omr, 0);
-
- /* Free ring */
- dma_free_coherent(priv->dev,
- priv->msg_tx_ring.size * RIO_MSG_DESC_SIZE,
- priv->msg_tx_ring.virt, priv->msg_tx_ring.phys);
-
- /* Free interrupt */
- free_irq(IRQ_RIO_TX(mport), (void *)mport);
-}
-
-/**
- * fsl_rio_rx_handler - MPC85xx inbound message interrupt handler
- * @irq: Linux interrupt number
- * @dev_instance: Pointer to interrupt-specific data
- *
- * Handles inbound message interrupts. Executes a registered inbound
- * mailbox event handler and acks the interrupt occurrence.
- */
-static irqreturn_t
-fsl_rio_rx_handler(int irq, void *dev_instance)
-{
- int isr;
- struct rio_mport *port = (struct rio_mport *)dev_instance;
- struct rio_priv *priv = port->priv;
-
- isr = in_be32(&priv->msg_regs->isr);
-
- if (isr & RIO_MSG_ISR_TE) {
- pr_info("RIO: inbound message reception error\n");
- out_be32((void *)&priv->msg_regs->isr, RIO_MSG_ISR_TE);
- goto out;
- }
-
- /* XXX Need to check/dispatch until queue empty */
- if (isr & RIO_MSG_ISR_DIQI) {
- /*
- * We implement *only* mailbox 0, but can receive messages
- * for any mailbox/letter to that mailbox destination. So,
- * make the callback with an unknown/invalid mailbox number
- * argument.
- */
- port->inb_msg[0].mcback(port, priv->msg_rx_ring.dev_id, -1, -1);
-
- /* Ack the queueing interrupt */
- out_be32(&priv->msg_regs->isr, RIO_MSG_ISR_DIQI);
- }
-
- out:
- return IRQ_HANDLED;
-}
-
-/**
- * fsl_open_inb_mbox - Initialize MPC85xx inbound mailbox
- * @mport: Master port implementing the inbound message unit
- * @dev_id: Device specific pointer to pass on event
- * @mbox: Mailbox to open
- * @entries: Number of entries in the inbound mailbox ring
- *
- * Initializes buffer ring, request the inbound message interrupt,
- * and enables the inbound message unit. Returns %0 on success
- * and %-EINVAL or %-ENOMEM on failure.
- */
-static int
-fsl_open_inb_mbox(struct rio_mport *mport, void *dev_id, int mbox, int entries)
-{
- int i, rc = 0;
- struct rio_priv *priv = mport->priv;
-
- if ((entries < RIO_MIN_RX_RING_SIZE) ||
- (entries > RIO_MAX_RX_RING_SIZE) || (!is_power_of_2(entries))) {
- rc = -EINVAL;
- goto out;
- }
-
- /* Initialize client buffer ring */
- priv->msg_rx_ring.dev_id = dev_id;
- priv->msg_rx_ring.size = entries;
- priv->msg_rx_ring.rx_slot = 0;
- for (i = 0; i < priv->msg_rx_ring.size; i++)
- priv->msg_rx_ring.virt_buffer[i] = NULL;
-
- /* Initialize inbound message ring */
- priv->msg_rx_ring.virt = dma_alloc_coherent(priv->dev,
- priv->msg_rx_ring.size * RIO_MAX_MSG_SIZE,
- &priv->msg_rx_ring.phys, GFP_KERNEL);
- if (!priv->msg_rx_ring.virt) {
- rc = -ENOMEM;
- goto out;
- }
-
- /* Point dequeue/enqueue pointers at first entry in ring */
- out_be32(&priv->msg_regs->ifqdpar, (u32) priv->msg_rx_ring.phys);
- out_be32(&priv->msg_regs->ifqepar, (u32) priv->msg_rx_ring.phys);
-
- /* Clear interrupt status */
- out_be32(&priv->msg_regs->isr, 0x00000091);
-
- /* Hook up inbound message handler */
- rc = request_irq(IRQ_RIO_RX(mport), fsl_rio_rx_handler, 0,
- "msg_rx", (void *)mport);
- if (rc < 0) {
- dma_free_coherent(priv->dev, RIO_MSG_BUFFER_SIZE,
- priv->msg_tx_ring.virt_buffer[i],
- priv->msg_tx_ring.phys_buffer[i]);
- goto out;
- }
-
- /*
- * Configure inbound message unit:
- * Snooping
- * 4KB max message size
- * Unmask all interrupt sources
- * Disable
- */
- out_be32(&priv->msg_regs->imr, 0x001b0060);
-
- /* Set number of queue entries */
- setbits32(&priv->msg_regs->imr, (get_bitmask_order(entries) - 2) << 12);
-
- /* Now enable the unit */
- setbits32(&priv->msg_regs->imr, 0x1);
-
- out:
- return rc;
-}
-
-/**
- * fsl_close_inb_mbox - Shut down MPC85xx inbound mailbox
- * @mport: Master port implementing the inbound message unit
- * @mbox: Mailbox to close
- *
- * Disables the inbound message unit, free all buffers, and
- * frees the inbound message interrupt.
- */
-static void fsl_close_inb_mbox(struct rio_mport *mport, int mbox)
-{
- struct rio_priv *priv = mport->priv;
- /* Disable inbound message unit */
- out_be32(&priv->msg_regs->imr, 0);
-
- /* Free ring */
- dma_free_coherent(priv->dev, priv->msg_rx_ring.size * RIO_MAX_MSG_SIZE,
- priv->msg_rx_ring.virt, priv->msg_rx_ring.phys);
-
- /* Free interrupt */
- free_irq(IRQ_RIO_RX(mport), (void *)mport);
-}
-
-/**
- * fsl_add_inb_buffer - Add buffer to the MPC85xx inbound message queue
- * @mport: Master port implementing the inbound message unit
- * @mbox: Inbound mailbox number
- * @buf: Buffer to add to inbound queue
- *
- * Adds the @buf buffer to the MPC85xx inbound message queue. Returns
- * %0 on success or %-EINVAL on failure.
- */
-static int fsl_add_inb_buffer(struct rio_mport *mport, int mbox, void *buf)
-{
- int rc = 0;
- struct rio_priv *priv = mport->priv;
-
- pr_debug("RIO: fsl_add_inb_buffer(), msg_rx_ring.rx_slot %d\n",
- priv->msg_rx_ring.rx_slot);
-
- if (priv->msg_rx_ring.virt_buffer[priv->msg_rx_ring.rx_slot]) {
- printk(KERN_ERR
- "RIO: error adding inbound buffer %d, buffer exists\n",
- priv->msg_rx_ring.rx_slot);
- rc = -EINVAL;
- goto out;
- }
-
- priv->msg_rx_ring.virt_buffer[priv->msg_rx_ring.rx_slot] = buf;
- if (++priv->msg_rx_ring.rx_slot == priv->msg_rx_ring.size)
- priv->msg_rx_ring.rx_slot = 0;
-
- out:
- return rc;
-}
-
-/**
- * fsl_get_inb_message - Fetch inbound message from the MPC85xx message unit
- * @mport: Master port implementing the inbound message unit
- * @mbox: Inbound mailbox number
- *
- * Gets the next available inbound message from the inbound message queue.
- * A pointer to the message is returned on success or NULL on failure.
- */
-static void *fsl_get_inb_message(struct rio_mport *mport, int mbox)
-{
- struct rio_priv *priv = mport->priv;
- u32 phys_buf, virt_buf;
- void *buf = NULL;
- int buf_idx;
-
- phys_buf = in_be32(&priv->msg_regs->ifqdpar);
-
- /* If no more messages, then bail out */
- if (phys_buf == in_be32(&priv->msg_regs->ifqepar))
- goto out2;
-
- virt_buf = (u32) priv->msg_rx_ring.virt + (phys_buf
- - priv->msg_rx_ring.phys);
- buf_idx = (phys_buf - priv->msg_rx_ring.phys) / RIO_MAX_MSG_SIZE;
- buf = priv->msg_rx_ring.virt_buffer[buf_idx];
-
- if (!buf) {
- printk(KERN_ERR
- "RIO: inbound message copy failed, no buffers\n");
- goto out1;
- }
-
- /* Copy max message size, caller is expected to allocate that big */
- memcpy(buf, (void *)virt_buf, RIO_MAX_MSG_SIZE);
-
- /* Clear the available buffer */
- priv->msg_rx_ring.virt_buffer[buf_idx] = NULL;
-
- out1:
- setbits32(&priv->msg_regs->imr, RIO_MSG_IMR_MI);
-
- out2:
- return buf;
-}
-
-/**
- * fsl_rio_dbell_handler - MPC85xx doorbell interrupt handler
- * @irq: Linux interrupt number
- * @dev_instance: Pointer to interrupt-specific data
- *
- * Handles doorbell interrupts. Parses a list of registered
- * doorbell event handlers and executes a matching event handler.
- */
-static irqreturn_t
-fsl_rio_dbell_handler(int irq, void *dev_instance)
-{
- int dsr;
- struct rio_mport *port = (struct rio_mport *)dev_instance;
- struct rio_priv *priv = port->priv;
-
- dsr = in_be32(&priv->msg_regs->dsr);
-
- if (dsr & DOORBELL_DSR_TE) {
- pr_info("RIO: doorbell reception error\n");
- out_be32(&priv->msg_regs->dsr, DOORBELL_DSR_TE);
- goto out;
- }
-
- if (dsr & DOORBELL_DSR_QFI) {
- pr_info("RIO: doorbell queue full\n");
- out_be32(&priv->msg_regs->dsr, DOORBELL_DSR_QFI);
- }
-
- /* XXX Need to check/dispatch until queue empty */
- if (dsr & DOORBELL_DSR_DIQI) {
- u32 dmsg =
- (u32) priv->dbell_ring.virt +
- (in_be32(&priv->msg_regs->dqdpar) & 0xfff);
- struct rio_dbell *dbell;
- int found = 0;
-
- pr_debug
- ("RIO: processing doorbell, sid %2.2x tid %2.2x info %4.4x\n",
- DBELL_SID(dmsg), DBELL_TID(dmsg), DBELL_INF(dmsg));
-
- list_for_each_entry(dbell, &port->dbells, node) {
- if ((dbell->res->start <= DBELL_INF(dmsg)) &&
- (dbell->res->end >= DBELL_INF(dmsg))) {
- found = 1;
- break;
- }
- }
- if (found) {
- dbell->dinb(port, dbell->dev_id, DBELL_SID(dmsg), DBELL_TID(dmsg),
- DBELL_INF(dmsg));
- } else {
- pr_debug
- ("RIO: spurious doorbell, sid %2.2x tid %2.2x info %4.4x\n",
- DBELL_SID(dmsg), DBELL_TID(dmsg), DBELL_INF(dmsg));
- }
- setbits32(&priv->msg_regs->dmr, DOORBELL_DMR_DI);
- out_be32(&priv->msg_regs->dsr, DOORBELL_DSR_DIQI);
- }
-
- out:
- return IRQ_HANDLED;
-}
-
-/**
- * fsl_rio_doorbell_init - MPC85xx doorbell interface init
- * @mport: Master port implementing the inbound doorbell unit
- *
- * Initializes doorbell unit hardware and inbound DMA buffer
- * ring. Called from fsl_rio_setup(). Returns %0 on success
- * or %-ENOMEM on failure.
- */
-static int fsl_rio_doorbell_init(struct rio_mport *mport)
-{
- struct rio_priv *priv = mport->priv;
- int rc = 0;
-
- /* Map outbound doorbell window immediately after maintenance window */
- priv->dbell_win = ioremap(mport->iores.start + RIO_MAINT_WIN_SIZE,
- RIO_DBELL_WIN_SIZE);
- if (!priv->dbell_win) {
- printk(KERN_ERR
- "RIO: unable to map outbound doorbell window\n");
- rc = -ENOMEM;
- goto out;
- }
-
- /* Initialize inbound doorbells */
- priv->dbell_ring.virt = dma_alloc_coherent(priv->dev, 512 *
- DOORBELL_MESSAGE_SIZE, &priv->dbell_ring.phys, GFP_KERNEL);
- if (!priv->dbell_ring.virt) {
- printk(KERN_ERR "RIO: unable allocate inbound doorbell ring\n");
- rc = -ENOMEM;
- iounmap(priv->dbell_win);
- goto out;
- }
-
- /* Point dequeue/enqueue pointers at first entry in ring */
- out_be32(&priv->msg_regs->dqdpar, (u32) priv->dbell_ring.phys);
- out_be32(&priv->msg_regs->dqepar, (u32) priv->dbell_ring.phys);
-
- /* Clear interrupt status */
- out_be32(&priv->msg_regs->dsr, 0x00000091);
-
- /* Hook up doorbell handler */
- rc = request_irq(IRQ_RIO_BELL(mport), fsl_rio_dbell_handler, 0,
- "dbell_rx", (void *)mport);
- if (rc < 0) {
- iounmap(priv->dbell_win);
- dma_free_coherent(priv->dev, 512 * DOORBELL_MESSAGE_SIZE,
- priv->dbell_ring.virt, priv->dbell_ring.phys);
- printk(KERN_ERR
- "MPC85xx RIO: unable to request inbound doorbell irq");
- goto out;
- }
-
- /* Configure doorbells for snooping, 512 entries, and enable */
- out_be32(&priv->msg_regs->dmr, 0x00108161);
-
- out:
- return rc;
-}
-
-static void port_error_handler(struct rio_mport *port, int offset)
+void fsl_rio_port_error_handler(struct rio_mport *port, int offset)
{
/*XXX: Error recovery is not implemented, we just clear errors */
out_be32((u32 *)(rio_regs_win + RIO_LTLEDCSR), 0);
@@ -1098,263 +275,6 @@ static void port_error_handler(struct rio_mport *port, int offset)
out_be32((u32 *)(rio_regs_win + RIO_PORT2_ESCSR), ESCSR_CLEAR);
}
}
-
-static void msg_unit_error_handler(struct rio_mport *port)
-{
- struct rio_priv *priv = port->priv;
-
- /*XXX: Error recovery is not implemented, we just clear errors */
- out_be32((u32 *)(rio_regs_win + RIO_LTLEDCSR), 0);
-
- out_be32((u32 *)(rio_regs_win + RIO_IM0SR), IMSR_CLEAR);
- out_be32((u32 *)(rio_regs_win + RIO_IM1SR), IMSR_CLEAR);
- out_be32((u32 *)(rio_regs_win + RIO_OM0SR), OMSR_CLEAR);
- out_be32((u32 *)(rio_regs_win + RIO_OM1SR), OMSR_CLEAR);
-
- out_be32(&priv->msg_regs->odsr, ODSR_CLEAR);
- out_be32(&priv->msg_regs->dsr, IDSR_CLEAR);
-
- out_be32(&priv->msg_regs->pwsr, IPWSR_CLEAR);
-}
-
-/**
- * fsl_rio_port_write_handler - MPC85xx port write interrupt handler
- * @irq: Linux interrupt number
- * @dev_instance: Pointer to interrupt-specific data
- *
- * Handles port write interrupts. Parses a list of registered
- * port write event handlers and executes a matching event handler.
- */
-static irqreturn_t
-fsl_rio_port_write_handler(int irq, void *dev_instance)
-{
- u32 ipwmr, ipwsr;
- struct rio_mport *port = (struct rio_mport *)dev_instance;
- struct rio_priv *priv = port->priv;
- u32 epwisr, tmp;
-
- epwisr = in_be32(priv->regs_win + RIO_EPWISR);
- if (!(epwisr & RIO_EPWISR_PW))
- goto pw_done;
-
- ipwmr = in_be32(&priv->msg_regs->pwmr);
- ipwsr = in_be32(&priv->msg_regs->pwsr);
-
-#ifdef DEBUG_PW
- pr_debug("PW Int->IPWMR: 0x%08x IPWSR: 0x%08x (", ipwmr, ipwsr);
- if (ipwsr & RIO_IPWSR_QF)
- pr_debug(" QF");
- if (ipwsr & RIO_IPWSR_TE)
- pr_debug(" TE");
- if (ipwsr & RIO_IPWSR_QFI)
- pr_debug(" QFI");
- if (ipwsr & RIO_IPWSR_PWD)
- pr_debug(" PWD");
- if (ipwsr & RIO_IPWSR_PWB)
- pr_debug(" PWB");
- pr_debug(" )\n");
-#endif
- /* Schedule deferred processing if PW was received */
- if (ipwsr & RIO_IPWSR_QFI) {
- /* Save PW message (if there is room in FIFO),
- * otherwise discard it.
- */
- if (kfifo_avail(&priv->pw_fifo) >= RIO_PW_MSG_SIZE) {
- priv->port_write_msg.msg_count++;
- kfifo_in(&priv->pw_fifo, priv->port_write_msg.virt,
- RIO_PW_MSG_SIZE);
- } else {
- priv->port_write_msg.discard_count++;
- pr_debug("RIO: ISR Discarded Port-Write Msg(s) (%d)\n",
- priv->port_write_msg.discard_count);
- }
- /* Clear interrupt and issue Clear Queue command. This allows
- * another port-write to be received.
- */
- out_be32(&priv->msg_regs->pwsr, RIO_IPWSR_QFI);
- out_be32(&priv->msg_regs->pwmr, ipwmr | RIO_IPWMR_CQ);
-
- schedule_work(&priv->pw_work);
- }
-
- if ((ipwmr & RIO_IPWMR_EIE) && (ipwsr & RIO_IPWSR_TE)) {
- priv->port_write_msg.err_count++;
- pr_debug("RIO: Port-Write Transaction Err (%d)\n",
- priv->port_write_msg.err_count);
- /* Clear Transaction Error: port-write controller should be
- * disabled when clearing this error
- */
- out_be32(&priv->msg_regs->pwmr, ipwmr & ~RIO_IPWMR_PWE);
- out_be32(&priv->msg_regs->pwsr, RIO_IPWSR_TE);
- out_be32(&priv->msg_regs->pwmr, ipwmr);
- }
-
- if (ipwsr & RIO_IPWSR_PWD) {
- priv->port_write_msg.discard_count++;
- pr_debug("RIO: Port Discarded Port-Write Msg(s) (%d)\n",
- priv->port_write_msg.discard_count);
- out_be32(&priv->msg_regs->pwsr, RIO_IPWSR_PWD);
- }
-
-pw_done:
- if (epwisr & RIO_EPWISR_PINT1) {
- tmp = in_be32(priv->regs_win + RIO_LTLEDCSR);
- pr_debug("RIO_LTLEDCSR = 0x%x\n", tmp);
- port_error_handler(port, 0);
- }
-
- if (epwisr & RIO_EPWISR_PINT2) {
- tmp = in_be32(priv->regs_win + RIO_LTLEDCSR);
- pr_debug("RIO_LTLEDCSR = 0x%x\n", tmp);
- port_error_handler(port, 1);
- }
-
- if (epwisr & RIO_EPWISR_MU) {
- tmp = in_be32(priv->regs_win + RIO_LTLEDCSR);
- pr_debug("RIO_LTLEDCSR = 0x%x\n", tmp);
- msg_unit_error_handler(port);
- }
-
- return IRQ_HANDLED;
-}
-
-static void fsl_pw_dpc(struct work_struct *work)
-{
- struct rio_priv *priv = container_of(work, struct rio_priv, pw_work);
- unsigned long flags;
- u32 msg_buffer[RIO_PW_MSG_SIZE/sizeof(u32)];
-
- /*
- * Process port-write messages
- */
- spin_lock_irqsave(&priv->pw_fifo_lock, flags);
- while (kfifo_out(&priv->pw_fifo, (unsigned char *)msg_buffer,
- RIO_PW_MSG_SIZE)) {
- /* Process one message */
- spin_unlock_irqrestore(&priv->pw_fifo_lock, flags);
-#ifdef DEBUG_PW
- {
- u32 i;
- pr_debug("%s : Port-Write Message:", __func__);
- for (i = 0; i < RIO_PW_MSG_SIZE/sizeof(u32); i++) {
- if ((i%4) == 0)
- pr_debug("\n0x%02x: 0x%08x", i*4,
- msg_buffer[i]);
- else
- pr_debug(" 0x%08x", msg_buffer[i]);
- }
- pr_debug("\n");
- }
-#endif
- /* Pass the port-write message to RIO core for processing */
- rio_inb_pwrite_handler((union rio_pw_msg *)msg_buffer);
- spin_lock_irqsave(&priv->pw_fifo_lock, flags);
- }
- spin_unlock_irqrestore(&priv->pw_fifo_lock, flags);
-}
-
-/**
- * fsl_rio_pw_enable - enable/disable port-write interface init
- * @mport: Master port implementing the port write unit
- * @enable: 1=enable; 0=disable port-write message handling
- */
-static int fsl_rio_pw_enable(struct rio_mport *mport, int enable)
-{
- struct rio_priv *priv = mport->priv;
- u32 rval;
-
- rval = in_be32(&priv->msg_regs->pwmr);
-
- if (enable)
- rval |= RIO_IPWMR_PWE;
- else
- rval &= ~RIO_IPWMR_PWE;
-
- out_be32(&priv->msg_regs->pwmr, rval);
-
- return 0;
-}
-
-/**
- * fsl_rio_port_write_init - MPC85xx port write interface init
- * @mport: Master port implementing the port write unit
- *
- * Initializes port write unit hardware and DMA buffer
- * ring. Called from fsl_rio_setup(). Returns %0 on success
- * or %-ENOMEM on failure.
- */
-static int fsl_rio_port_write_init(struct rio_mport *mport)
-{
- struct rio_priv *priv = mport->priv;
- int rc = 0;
-
- /* Following configurations require a disabled port write controller */
- out_be32(&priv->msg_regs->pwmr,
- in_be32(&priv->msg_regs->pwmr) & ~RIO_IPWMR_PWE);
-
- /* Initialize port write */
- priv->port_write_msg.virt = dma_alloc_coherent(priv->dev,
- RIO_PW_MSG_SIZE,
- &priv->port_write_msg.phys, GFP_KERNEL);
- if (!priv->port_write_msg.virt) {
- pr_err("RIO: unable allocate port write queue\n");
- return -ENOMEM;
- }
-
- priv->port_write_msg.err_count = 0;
- priv->port_write_msg.discard_count = 0;
-
- /* Point dequeue/enqueue pointers at first entry */
- out_be32(&priv->msg_regs->epwqbar, 0);
- out_be32(&priv->msg_regs->pwqbar, (u32) priv->port_write_msg.phys);
-
- pr_debug("EIPWQBAR: 0x%08x IPWQBAR: 0x%08x\n",
- in_be32(&priv->msg_regs->epwqbar),
- in_be32(&priv->msg_regs->pwqbar));
-
- /* Clear interrupt status IPWSR */
- out_be32(&priv->msg_regs->pwsr,
- (RIO_IPWSR_TE | RIO_IPWSR_QFI | RIO_IPWSR_PWD));
-
- /* Configure port write contoller for snooping enable all reporting,
- clear queue full */
- out_be32(&priv->msg_regs->pwmr,
- RIO_IPWMR_SEN | RIO_IPWMR_QFIE | RIO_IPWMR_EIE | RIO_IPWMR_CQ);
-
-
- /* Hook up port-write handler */
- rc = request_irq(IRQ_RIO_PW(mport), fsl_rio_port_write_handler,
- IRQF_SHARED, "port-write", (void *)mport);
- if (rc < 0) {
- pr_err("MPC85xx RIO: unable to request inbound doorbell irq");
- goto err_out;
- }
- /* Enable Error Interrupt */
- out_be32((u32 *)(rio_regs_win + RIO_LTLEECSR), LTLEECSR_ENABLE_ALL);
-
- INIT_WORK(&priv->pw_work, fsl_pw_dpc);
- spin_lock_init(&priv->pw_fifo_lock);
- if (kfifo_alloc(&priv->pw_fifo, RIO_PW_MSG_SIZE * 32, GFP_KERNEL)) {
- pr_err("FIFO allocation failed\n");
- rc = -ENOMEM;
- goto err_out_irq;
- }
-
- pr_debug("IPWMR: 0x%08x IPWSR: 0x%08x\n",
- in_be32(&priv->msg_regs->pwmr),
- in_be32(&priv->msg_regs->pwsr));
-
- return rc;
-
-err_out_irq:
- free_irq(IRQ_RIO_PW(mport), (void *)mport);
-err_out:
- dma_free_coherent(priv->dev, RIO_PW_MSG_SIZE,
- priv->port_write_msg.virt,
- priv->port_write_msg.phys);
- return rc;
-}
-
static inline void fsl_rio_info(struct device *dev, u32 ccsr)
{
const char *str;
@@ -1429,7 +349,8 @@ int fsl_rio_setup(struct platform_device *dev)
dev->dev.of_node->full_name);
return -EFAULT;
}
- dev_info(&dev->dev, "Of-device full name %s\n", dev->dev.of_node->full_name);
+ dev_info(&dev->dev, "Of-device full name %s\n",
+ dev->dev.of_node->full_name);
dev_info(&dev->dev, "Regs: %pR\n", ®s);
dt_range = of_get_property(dev->dev.of_node, "ranges", &rlen);
@@ -1469,15 +390,7 @@ int fsl_rio_setup(struct platform_device *dev)
ops->lcwrite = fsl_local_config_write;
ops->cread = fsl_rio_config_read;
ops->cwrite = fsl_rio_config_write;
- ops->dsend = fsl_rio_doorbell_send;
ops->pwenable = fsl_rio_pw_enable;
- ops->open_outb_mbox = fsl_open_outb_mbox;
- ops->open_inb_mbox = fsl_open_inb_mbox;
- ops->close_outb_mbox = fsl_close_outb_mbox;
- ops->close_inb_mbox = fsl_close_inb_mbox;
- ops->add_outb_message = fsl_add_outb_message;
- ops->add_inb_buffer = fsl_add_inb_buffer;
- ops->get_inb_message = fsl_get_inb_message;
port = kzalloc(sizeof(struct rio_mport), GFP_KERNEL);
if (!port) {
@@ -1507,16 +420,8 @@ int fsl_rio_setup(struct platform_device *dev)
goto err_res;
}
- priv->pwirq = irq_of_parse_and_map(dev->dev.of_node, 0);
- priv->bellirq = irq_of_parse_and_map(dev->dev.of_node, 2);
- priv->txirq = irq_of_parse_and_map(dev->dev.of_node, 3);
- priv->rxirq = irq_of_parse_and_map(dev->dev.of_node, 4);
- dev_info(&dev->dev, "pwirq: %d, bellirq: %d, txirq: %d, rxirq %d\n",
- priv->pwirq, priv->bellirq, priv->txirq, priv->rxirq);
-
- rio_init_dbell_res(&port->riores[RIO_DOORBELL_RESOURCE], 0, 0xffff);
- rio_init_mbox_res(&port->riores[RIO_INB_MBOX_RESOURCE], 0, 0);
- rio_init_mbox_res(&port->riores[RIO_OUTB_MBOX_RESOURCE], 0, 0);
+ priv->pwirq = irq_of_parse_and_map(dev->dev.of_node, 0);
+ dev_info(&dev->dev, "pwirq: %d\n", priv->pwirq);
strcpy(port->name, "RIO0 mport");
priv->dev = &dev->dev;
@@ -1538,7 +443,7 @@ int fsl_rio_setup(struct platform_device *dev)
/* Checking the port training status */
if (in_be32((priv->regs_win + RIO_ESCSR)) & 1) {
dev_err(&dev->dev, "Port is not ready. "
- "Try to restart connection...\n");
+ "Try to restart connection...\n");
switch (port->phy_type) {
case RIO_PHY_SERIAL:
/* Disable ports */
@@ -1582,10 +487,6 @@ int fsl_rio_setup(struct platform_device *dev)
priv->atmu_regs = (struct rio_atmu_regs *)(priv->regs_win
+ RIO_ATMU_REGS_OFFSET);
priv->maint_atmu_regs = priv->atmu_regs + 1;
- priv->dbell_atmu_regs = priv->atmu_regs + 2;
- priv->msg_regs = (struct rio_msg_regs *)(priv->regs_win +
- ((port->phy_type == RIO_PHY_SERIAL) ?
- RIO_S_MSG_REGS_OFFSET : RIO_P_MSG_REGS_OFFSET));
/* Set to receive any dist ID for serial RapidIO controller. */
if (port->phy_type == RIO_PHY_SERIAL)
@@ -1598,11 +499,8 @@ int fsl_rio_setup(struct platform_device *dev)
priv->maint_win = ioremap(law_start, RIO_MAINT_WIN_SIZE);
- /* Configure outbound doorbell window */
- out_be32(&priv->dbell_atmu_regs->rowbar,
- (law_start + RIO_MAINT_WIN_SIZE) >> 12);
- out_be32(&priv->dbell_atmu_regs->rowar, 0x8004200b); /* 4k */
- fsl_rio_doorbell_init(port);
+ fsl_rio_setup_rmu(port, dev->dev.of_node);
+
fsl_rio_port_write_init(port);
return 0;
diff --git a/arch/powerpc/sysdev/fsl_rio.h b/arch/powerpc/sysdev/fsl_rio.h
new file mode 100644
index 0000000..f888a1e
--- /dev/null
+++ b/arch/powerpc/sysdev/fsl_rio.h
@@ -0,0 +1,78 @@
+/*
+ * Freescale MPC85xx/MPC86xx RapidIO support
+ *
+ * Copyright 2009 Sysgo AG
+ * Thomas Moll <thomas.moll@sysgo.com>
+ * - fixed maintenance access routines, check for aligned access
+ *
+ * Copyright 2009 Integrated Device Technology, Inc.
+ * Alex Bounine <alexandre.bounine@idt.com>
+ * - Added Port-Write message handling
+ * - Added Machine Check exception handling
+ *
+ * Copyright (C) 2007, 2008, 2010, 2011 Freescale Semiconductor, Inc.
+ * Zhang Wei <wei.zhang@freescale.com>
+ * Lian Minghuan-B31939 <Minghuan.Lian@freescale.com>
+ * Liu Gang <Gang.Liu@freescale.com>
+ *
+ * Copyright 2005 MontaVista Software, Inc.
+ * Matt Porter <mporter@kernel.crashing.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __FSL_RIO_H
+#define __FSL_RIO_H
+
+#include <linux/rio.h>
+#include <linux/rio_drv.h>
+#include <linux/kfifo.h>
+
+#define RIO_REGS_WIN(mport) (((struct rio_priv *)(mport->priv))->regs_win)
+
+#define RIO_MAINT_WIN_SIZE 0x400000
+#define RIO_LTLEDCSR 0x0608
+
+struct rio_atmu_regs {
+ u32 rowtar;
+ u32 rowtear;
+ u32 rowbar;
+ u32 pad2;
+ u32 rowar;
+ u32 pad3[3];
+};
+
+struct rio_port_write_msg {
+ void *virt;
+ dma_addr_t phys;
+ u32 msg_count;
+ u32 err_count;
+ u32 discard_count;
+};
+
+struct rio_priv {
+ struct device *dev;
+ void __iomem *regs_win;
+ struct rio_atmu_regs __iomem *atmu_regs;
+ struct rio_atmu_regs __iomem *maint_atmu_regs;
+ void __iomem *maint_win;
+ struct rio_port_write_msg port_write_msg;
+ int pwirq;
+ struct work_struct pw_work;
+ struct kfifo pw_fifo;
+ spinlock_t pw_fifo_lock;
+ void *rmm_handle; /* RapidIO message manager(unit) Handle */
+};
+
+extern void __iomem *rio_regs_win;
+
+extern int fsl_rio_setup_rmu(struct rio_mport *mport,
+ struct device_node *node);
+extern int fsl_rio_port_write_init(struct rio_mport *mport);
+extern int fsl_rio_pw_enable(struct rio_mport *mport, int enable);
+extern void fsl_rio_port_error_handler(struct rio_mport *port, int offset);
+
+#endif
diff --git a/arch/powerpc/sysdev/fsl_rmu.c b/arch/powerpc/sysdev/fsl_rmu.c
new file mode 100644
index 0000000..0a3e6cf
--- /dev/null
+++ b/arch/powerpc/sysdev/fsl_rmu.c
@@ -0,0 +1,1163 @@
+/*
+ * Freescale MPC85xx/MPC86xx RapidIO RMU support
+ *
+ * Copyright 2009 Sysgo AG
+ * Thomas Moll <thomas.moll@sysgo.com>
+ * - fixed maintenance access routines, check for aligned access
+ *
+ * Copyright 2009 Integrated Device Technology, Inc.
+ * Alex Bounine <alexandre.bounine@idt.com>
+ * - Added Port-Write message handling
+ * - Added Machine Check exception handling
+ *
+ * Copyright (C) 2007, 2008, 2010, 2011 Freescale Semiconductor, Inc.
+ * Zhang Wei <wei.zhang@freescale.com>
+ * Lian Minghuan-B31939 <Minghuan.Lian@freescale.com>
+ * Liu Gang <Gang.Liu@freescale.com>
+ *
+ * Copyright 2005 MontaVista Software, Inc.
+ * Matt Porter <mporter@kernel.crashing.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/types.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+#include <linux/slab.h>
+
+#include "fsl_rio.h"
+
+#define GET_RMM_HANDLE(mport) \
+ (((struct rio_priv *)(mport->priv))->rmm_handle)
+
+/* RapidIO definition irq, which read from OF-tree */
+#define IRQ_RIO_PW(m) (((struct rio_priv *)(m->priv))->pwirq)
+#define IRQ_RIO_BELL(m) (((struct fsl_rmu *)(GET_RMM_HANDLE(m)))->bellirq)
+#define IRQ_RIO_TX(m) (((struct fsl_rmu *)(GET_RMM_HANDLE(m)))->txirq)
+#define IRQ_RIO_RX(m) (((struct fsl_rmu *)(GET_RMM_HANDLE(m)))->rxirq)
+
+#define RIO_MIN_TX_RING_SIZE 2
+#define RIO_MAX_TX_RING_SIZE 2048
+#define RIO_MIN_RX_RING_SIZE 2
+#define RIO_MAX_RX_RING_SIZE 2048
+
+#define RIO_IPWMR_SEN 0x00100000
+#define RIO_IPWMR_QFIE 0x00000100
+#define RIO_IPWMR_EIE 0x00000020
+#define RIO_IPWMR_CQ 0x00000002
+#define RIO_IPWMR_PWE 0x00000001
+
+#define RIO_IPWSR_QF 0x00100000
+#define RIO_IPWSR_TE 0x00000080
+#define RIO_IPWSR_QFI 0x00000010
+#define RIO_IPWSR_PWD 0x00000008
+#define RIO_IPWSR_PWB 0x00000004
+
+#define RIO_EPWISR 0x10010
+/* EPWISR Error match value */
+#define RIO_EPWISR_PINT1 0x80000000
+#define RIO_EPWISR_PINT2 0x40000000
+#define RIO_EPWISR_MU 0x00000002
+#define RIO_EPWISR_PW 0x00000001
+
+#define IPWSR_CLEAR 0x98
+#define OMSR_CLEAR 0x1cb3
+#define IMSR_CLEAR 0x491
+#define IDSR_CLEAR 0x91
+#define ODSR_CLEAR 0x1c00
+#define LTLEECSR_ENABLE_ALL 0xFFC000FC
+#define RIO_LTLEECSR 0x060c
+
+#define RIO_IM0SR 0x13064
+#define RIO_IM1SR 0x13164
+#define RIO_OM0SR 0x13004
+#define RIO_OM1SR 0x13104
+
+#define RIO_P_MSG_REGS_OFFSET 0x11000
+#define RIO_S_MSG_REGS_OFFSET 0x13000
+
+#define RIO_DBELL_WIN_SIZE 0x1000
+
+#define RIO_MSG_OMR_MUI 0x00000002
+#define RIO_MSG_OSR_TE 0x00000080
+#define RIO_MSG_OSR_QOI 0x00000020
+#define RIO_MSG_OSR_QFI 0x00000010
+#define RIO_MSG_OSR_MUB 0x00000004
+#define RIO_MSG_OSR_EOMI 0x00000002
+#define RIO_MSG_OSR_QEI 0x00000001
+
+#define RIO_MSG_IMR_MI 0x00000002
+#define RIO_MSG_ISR_TE 0x00000080
+#define RIO_MSG_ISR_QFI 0x00000010
+#define RIO_MSG_ISR_DIQI 0x00000001
+
+#define RIO_MSG_DESC_SIZE 32
+#define RIO_MSG_BUFFER_SIZE 4096
+
+#define DOORBELL_DMR_DI 0x00000002
+#define DOORBELL_DSR_TE 0x00000080
+#define DOORBELL_DSR_QFI 0x00000010
+#define DOORBELL_DSR_DIQI 0x00000001
+#define DOORBELL_TID_OFFSET 0x02
+#define DOORBELL_SID_OFFSET 0x04
+#define DOORBELL_INFO_OFFSET 0x06
+
+#define DOORBELL_MESSAGE_SIZE 0x08
+#define DBELL_SID(x) (*(u16 *)(x + DOORBELL_SID_OFFSET))
+#define DBELL_TID(x) (*(u16 *)(x + DOORBELL_TID_OFFSET))
+#define DBELL_INF(x) (*(u16 *)(x + DOORBELL_INFO_OFFSET))
+
+struct rio_msg_regs {
+ u32 omr; /* 0xD_3000 - Outbound message 0 mode register */
+ u32 osr; /* 0xD_3004 - Outbound message 0 status register */
+ u32 pad1;
+ u32 odqdpar; /* 0xD_300C - Outbound message 0 descriptor queue
+ dequeue pointer address register */
+ u32 pad2;
+ u32 osar; /* 0xD_3014 - Outbound message 0 source address
+ register */
+ u32 odpr; /* 0xD_3018 - Outbound message 0 destination port
+ register */
+ u32 odatr; /* 0xD_301C - Outbound message 0 destination attributes
+ Register*/
+ u32 odcr; /* 0xD_3020 - Outbound message 0 double-word count
+ register */
+ u32 pad3;
+ u32 odqepar; /* 0xD_3028 - Outbound message 0 descriptor queue
+ enqueue pointer address register */
+ u32 pad4[13];
+ u32 imr; /* 0xD_3060 - Inbound message 0 mode register */
+ u32 isr; /* 0xD_3064 - Inbound message 0 status register */
+ u32 pad5;
+ u32 ifqdpar; /* 0xD_306C - Inbound message 0 frame queue dequeue
+ pointer address register*/
+ u32 pad6;
+ u32 ifqepar; /* 0xD_3074 - Inbound message 0 frame queue enqueue
+ pointer address register */
+ u32 pad7[226];
+ u32 odmr; /* 0xD_3400 - Outbound doorbell mode register */
+ u32 odsr; /* 0xD_3404 - Outbound doorbell status register */
+ u32 res0[4];
+ u32 oddpr; /* 0xD_3418 - Outbound doorbell destination port
+ register */
+ u32 oddatr; /* 0xD_341c - Outbound doorbell destination attributes
+ register */
+ u32 res1[3];
+ u32 odretcr; /* 0xD_342C - Outbound doorbell retry error threshold
+ configuration register */
+ u32 res2[12];
+ u32 dmr; /* 0xD_3460 - Inbound doorbell mode register */
+ u32 dsr; /* 0xD_3464 - Inbound doorbell status register */
+ u32 pad8;
+ u32 dqdpar; /* 0xD_346C - Inbound doorbell queue dequeue Pointer
+ address register */
+ u32 pad9;
+ u32 dqepar; /* 0xD_3474 - Inbound doorbell Queue enqueue pointer
+ address register */
+ u32 pad10[26];
+ u32 pwmr; /* 0xD_34E0 - Inbound port-write mode register */
+ u32 pwsr; /* 0xD_34E4 - Inbound port-write status register */
+ u32 epwqbar; /* 0xD_34E8 - Extended Port-Write Queue Base Address
+ register */
+ u32 pwqbar; /* 0xD_34EC - Inbound port-write queue base address
+ register */
+};
+
+struct rio_tx_desc {
+ u32 res1;
+ u32 saddr;
+ u32 dport;
+ u32 dattr;
+ u32 res2;
+ u32 res3;
+ u32 dwcnt;
+ u32 res4;
+};
+
+struct rio_dbell_ring {
+ void *virt;
+ dma_addr_t phys;
+};
+
+struct rio_msg_tx_ring {
+ void *virt;
+ dma_addr_t phys;
+ void *virt_buffer[RIO_MAX_TX_RING_SIZE];
+ dma_addr_t phys_buffer[RIO_MAX_TX_RING_SIZE];
+ int tx_slot;
+ int size;
+ void *dev_id;
+};
+
+struct rio_msg_rx_ring {
+ void *virt;
+ dma_addr_t phys;
+ void *virt_buffer[RIO_MAX_RX_RING_SIZE];
+ int rx_slot;
+ int size;
+ void *dev_id;
+};
+
+struct fsl_rmu {
+ struct rio_atmu_regs __iomem *dbell_atmu_regs;
+ void __iomem *dbell_win;
+ struct rio_msg_regs __iomem *msg_regs;
+ struct rio_dbell_ring dbell_ring;
+ struct rio_msg_tx_ring msg_tx_ring;
+ struct rio_msg_rx_ring msg_rx_ring;
+ int bellirq;
+ int txirq;
+ int rxirq;
+};
+
+/**
+ * fsl_rio_tx_handler - MPC85xx outbound message interrupt handler
+ * @irq: Linux interrupt number
+ * @dev_instance: Pointer to interrupt-specific data
+ *
+ * Handles outbound message interrupts. Executes a register outbound
+ * mailbox event handler and acks the interrupt occurrence.
+ */
+static irqreturn_t
+fsl_rio_tx_handler(int irq, void *dev_instance)
+{
+ int osr;
+ struct rio_mport *port = (struct rio_mport *)dev_instance;
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(port);
+
+ osr = in_be32(&rmu->msg_regs->osr);
+
+ if (osr & RIO_MSG_OSR_TE) {
+ pr_info("RIO: outbound message transmission error\n");
+ out_be32(&rmu->msg_regs->osr, RIO_MSG_OSR_TE);
+ goto out;
+ }
+
+ if (osr & RIO_MSG_OSR_QOI) {
+ pr_info("RIO: outbound message queue overflow\n");
+ out_be32(&rmu->msg_regs->osr, RIO_MSG_OSR_QOI);
+ goto out;
+ }
+
+ if (osr & RIO_MSG_OSR_EOMI) {
+ u32 dqp = in_be32(&rmu->msg_regs->odqdpar);
+ int slot = (dqp - rmu->msg_tx_ring.phys) >> 5;
+ port->outb_msg[0].mcback(port, rmu->msg_tx_ring.dev_id, -1,
+ slot);
+
+ /* Ack the end-of-message interrupt */
+ out_be32(&rmu->msg_regs->osr, RIO_MSG_OSR_EOMI);
+ }
+
+out:
+ return IRQ_HANDLED;
+}
+
+/**
+ * fsl_rio_rx_handler - MPC85xx inbound message interrupt handler
+ * @irq: Linux interrupt number
+ * @dev_instance: Pointer to interrupt-specific data
+ *
+ * Handles inbound message interrupts. Executes a registered inbound
+ * mailbox event handler and acks the interrupt occurrence.
+ */
+static irqreturn_t
+fsl_rio_rx_handler(int irq, void *dev_instance)
+{
+ int isr;
+ struct rio_mport *port = (struct rio_mport *)dev_instance;
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(port);
+
+ isr = in_be32(&rmu->msg_regs->isr);
+
+ if (isr & RIO_MSG_ISR_TE) {
+ pr_info("RIO: inbound message reception error\n");
+ out_be32((void *)&rmu->msg_regs->isr, RIO_MSG_ISR_TE);
+ goto out;
+ }
+
+ /* XXX Need to check/dispatch until queue empty */
+ if (isr & RIO_MSG_ISR_DIQI) {
+ /*
+ * We implement *only* mailbox 0, but can receive messages
+ * for any mailbox/letter to that mailbox destination. So,
+ * make the callback with an unknown/invalid mailbox number
+ * argument.
+ */
+ port->inb_msg[0].mcback(port, rmu->msg_rx_ring.dev_id, -1, -1);
+
+ /* Ack the queueing interrupt */
+ out_be32(&rmu->msg_regs->isr, RIO_MSG_ISR_DIQI);
+ }
+
+out:
+ return IRQ_HANDLED;
+}
+
+/**
+ * fsl_rio_dbell_handler - MPC85xx doorbell interrupt handler
+ * @irq: Linux interrupt number
+ * @dev_instance: Pointer to interrupt-specific data
+ *
+ * Handles doorbell interrupts. Parses a list of registered
+ * doorbell event handlers and executes a matching event handler.
+ */
+static irqreturn_t
+fsl_rio_dbell_handler(int irq, void *dev_instance)
+{
+ int dsr;
+ struct rio_mport *port = (struct rio_mport *)dev_instance;
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(port);
+
+ dsr = in_be32(&rmu->msg_regs->dsr);
+
+ if (dsr & DOORBELL_DSR_TE) {
+ pr_info("RIO: doorbell reception error\n");
+ out_be32(&rmu->msg_regs->dsr, DOORBELL_DSR_TE);
+ goto out;
+ }
+
+ if (dsr & DOORBELL_DSR_QFI) {
+ pr_info("RIO: doorbell queue full\n");
+ out_be32(&rmu->msg_regs->dsr, DOORBELL_DSR_QFI);
+ }
+
+ /* XXX Need to check/dispatch until queue empty */
+ if (dsr & DOORBELL_DSR_DIQI) {
+ u32 dmsg =
+ (u32) rmu->dbell_ring.virt +
+ (in_be32(&rmu->msg_regs->dqdpar) & 0xfff);
+ struct rio_dbell *dbell;
+ int found = 0;
+
+ pr_debug
+ ("RIO: processing doorbell,"
+ " sid %2.2x tid %2.2x info %4.4x\n",
+ DBELL_SID(dmsg), DBELL_TID(dmsg), DBELL_INF(dmsg));
+
+ list_for_each_entry(dbell, &port->dbells, node) {
+ if ((dbell->res->start <= DBELL_INF(dmsg)) &&
+ (dbell->res->end >= DBELL_INF(dmsg))) {
+ found = 1;
+ break;
+ }
+ }
+ if (found) {
+ dbell->dinb(port, dbell->dev_id,
+ DBELL_SID(dmsg),
+ DBELL_TID(dmsg), DBELL_INF(dmsg));
+ } else {
+ pr_debug
+ ("RIO: spurious doorbell,"
+ " sid %2.2x tid %2.2x info %4.4x\n",
+ DBELL_SID(dmsg), DBELL_TID(dmsg),
+ DBELL_INF(dmsg));
+ }
+ setbits32(&rmu->msg_regs->dmr, DOORBELL_DMR_DI);
+ out_be32(&rmu->msg_regs->dsr, DOORBELL_DSR_DIQI);
+ }
+
+out:
+ return IRQ_HANDLED;
+}
+
+void msg_unit_error_handler(struct rio_mport *port)
+{
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(port);
+
+ /*XXX: Error recovery is not implemented, we just clear errors */
+ out_be32((u32 *)(rio_regs_win + RIO_LTLEDCSR), 0);
+
+ out_be32((u32 *)(rio_regs_win + RIO_IM0SR), IMSR_CLEAR);
+ out_be32((u32 *)(rio_regs_win + RIO_IM1SR), IMSR_CLEAR);
+ out_be32((u32 *)(rio_regs_win + RIO_OM0SR), OMSR_CLEAR);
+ out_be32((u32 *)(rio_regs_win + RIO_OM1SR), OMSR_CLEAR);
+
+ out_be32(&rmu->msg_regs->odsr, ODSR_CLEAR);
+ out_be32(&rmu->msg_regs->dsr, IDSR_CLEAR);
+
+ out_be32(&rmu->msg_regs->pwsr, IPWSR_CLEAR);
+}
+
+/**
+ * fsl_rio_port_write_handler - MPC85xx port write interrupt handler
+ * @irq: Linux interrupt number
+ * @dev_instance: Pointer to interrupt-specific data
+ *
+ * Handles port write interrupts. Parses a list of registered
+ * port write event handlers and executes a matching event handler.
+ */
+static irqreturn_t
+fsl_rio_port_write_handler(int irq, void *dev_instance)
+{
+ u32 ipwmr, ipwsr;
+ struct rio_mport *port = (struct rio_mport *)dev_instance;
+ struct rio_priv *priv = port->priv;
+ struct fsl_rmu *rmu;
+ u32 epwisr, tmp;
+
+ rmu = GET_RMM_HANDLE(port);
+ epwisr = in_be32(priv->regs_win + RIO_EPWISR);
+ if (!(epwisr & RIO_EPWISR_PW))
+ goto pw_done;
+
+ ipwmr = in_be32(&rmu->msg_regs->pwmr);
+ ipwsr = in_be32(&rmu->msg_regs->pwsr);
+
+#ifdef DEBUG_PW
+ pr_debug("PW Int->IPWMR: 0x%08x IPWSR: 0x%08x (", ipwmr, ipwsr);
+ if (ipwsr & RIO_IPWSR_QF)
+ pr_debug(" QF");
+ if (ipwsr & RIO_IPWSR_TE)
+ pr_debug(" TE");
+ if (ipwsr & RIO_IPWSR_QFI)
+ pr_debug(" QFI");
+ if (ipwsr & RIO_IPWSR_PWD)
+ pr_debug(" PWD");
+ if (ipwsr & RIO_IPWSR_PWB)
+ pr_debug(" PWB");
+ pr_debug(" )\n");
+#endif
+ /* Schedule deferred processing if PW was received */
+ if (ipwsr & RIO_IPWSR_QFI) {
+ /* Save PW message (if there is room in FIFO),
+ * otherwise discard it.
+ */
+ if (kfifo_avail(&priv->pw_fifo) >= RIO_PW_MSG_SIZE) {
+ priv->port_write_msg.msg_count++;
+ kfifo_in(&priv->pw_fifo, priv->port_write_msg.virt,
+ RIO_PW_MSG_SIZE);
+ } else {
+ priv->port_write_msg.discard_count++;
+ pr_debug("RIO: ISR Discarded Port-Write Msg(s) (%d)\n",
+ priv->port_write_msg.discard_count);
+ }
+ /* Clear interrupt and issue Clear Queue command. This allows
+ * another port-write to be received.
+ */
+ out_be32(&rmu->msg_regs->pwsr, RIO_IPWSR_QFI);
+ out_be32(&rmu->msg_regs->pwmr, ipwmr | RIO_IPWMR_CQ);
+
+ schedule_work(&priv->pw_work);
+ }
+
+ if ((ipwmr & RIO_IPWMR_EIE) && (ipwsr & RIO_IPWSR_TE)) {
+ priv->port_write_msg.err_count++;
+ pr_debug("RIO: Port-Write Transaction Err (%d)\n",
+ priv->port_write_msg.err_count);
+ /* Clear Transaction Error: port-write controller should be
+ * disabled when clearing this error
+ */
+ out_be32(&rmu->msg_regs->pwmr, ipwmr & ~RIO_IPWMR_PWE);
+ out_be32(&rmu->msg_regs->pwsr, RIO_IPWSR_TE);
+ out_be32(&rmu->msg_regs->pwmr, ipwmr);
+ }
+
+ if (ipwsr & RIO_IPWSR_PWD) {
+ priv->port_write_msg.discard_count++;
+ pr_debug("RIO: Port Discarded Port-Write Msg(s) (%d)\n",
+ priv->port_write_msg.discard_count);
+ out_be32(&rmu->msg_regs->pwsr, RIO_IPWSR_PWD);
+ }
+
+pw_done:
+ if (epwisr & RIO_EPWISR_PINT1) {
+ tmp = in_be32(priv->regs_win + RIO_LTLEDCSR);
+ pr_debug("RIO_LTLEDCSR = 0x%x\n", tmp);
+ fsl_rio_port_error_handler(port, 0);
+ }
+
+ if (epwisr & RIO_EPWISR_PINT2) {
+ tmp = in_be32(priv->regs_win + RIO_LTLEDCSR);
+ pr_debug("RIO_LTLEDCSR = 0x%x\n", tmp);
+ fsl_rio_port_error_handler(port, 1);
+ }
+
+ if (epwisr & RIO_EPWISR_MU) {
+ tmp = in_be32(priv->regs_win + RIO_LTLEDCSR);
+ pr_debug("RIO_LTLEDCSR = 0x%x\n", tmp);
+ msg_unit_error_handler(port);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static void fsl_pw_dpc(struct work_struct *work)
+{
+ struct rio_priv *priv = container_of(work, struct rio_priv, pw_work);
+ unsigned long flags;
+ u32 msg_buffer[RIO_PW_MSG_SIZE/sizeof(u32)];
+
+ /*
+ * Process port-write messages
+ */
+ spin_lock_irqsave(&priv->pw_fifo_lock, flags);
+ while (kfifo_out(&priv->pw_fifo, (unsigned char *)msg_buffer,
+ RIO_PW_MSG_SIZE)) {
+ /* Process one message */
+ spin_unlock_irqrestore(&priv->pw_fifo_lock, flags);
+#ifdef DEBUG_PW
+ {
+ u32 i;
+ pr_debug("%s : Port-Write Message:", __func__);
+ for (i = 0; i < RIO_PW_MSG_SIZE/sizeof(u32); i++) {
+ if ((i%4) == 0)
+ pr_debug("\n0x%02x: 0x%08x", i*4,
+ msg_buffer[i]);
+ else
+ pr_debug(" 0x%08x", msg_buffer[i]);
+ }
+ pr_debug("\n");
+ }
+#endif
+ /* Pass the port-write message to RIO core for processing */
+ rio_inb_pwrite_handler((union rio_pw_msg *)msg_buffer);
+ spin_lock_irqsave(&priv->pw_fifo_lock, flags);
+ }
+ spin_unlock_irqrestore(&priv->pw_fifo_lock, flags);
+}
+
+/**
+ * fsl_rio_pw_enable - enable/disable port-write interface init
+ * @mport: Master port implementing the port write unit
+ * @enable: 1=enable; 0=disable port-write message handling
+ */
+int fsl_rio_pw_enable(struct rio_mport *mport, int enable)
+{
+ struct fsl_rmu *rmu;
+ u32 rval;
+
+ rmu = GET_RMM_HANDLE(mport);
+
+ rval = in_be32(&rmu->msg_regs->pwmr);
+
+ if (enable)
+ rval |= RIO_IPWMR_PWE;
+ else
+ rval &= ~RIO_IPWMR_PWE;
+
+ out_be32(&rmu->msg_regs->pwmr, rval);
+
+ return 0;
+}
+
+/**
+ * fsl_rio_port_write_init - MPC85xx port write interface init
+ * @mport: Master port implementing the port write unit
+ *
+ * Initializes port write unit hardware and DMA buffer
+ * ring. Called from fsl_rio_setup(). Returns %0 on success
+ * or %-ENOMEM on failure.
+ */
+
+int fsl_rio_port_write_init(struct rio_mport *mport)
+{
+ struct rio_priv *priv = mport->priv;
+ struct fsl_rmu *rmu;
+ int rc = 0;
+
+ rmu = GET_RMM_HANDLE(mport);
+
+ /* Following configurations require a disabled port write controller */
+ out_be32(&rmu->msg_regs->pwmr,
+ in_be32(&rmu->msg_regs->pwmr) & ~RIO_IPWMR_PWE);
+
+ /* Initialize port write */
+ priv->port_write_msg.virt = dma_alloc_coherent(priv->dev,
+ RIO_PW_MSG_SIZE,
+ &priv->port_write_msg.phys, GFP_KERNEL);
+ if (!priv->port_write_msg.virt) {
+ pr_err("RIO: unable allocate port write queue\n");
+ return -ENOMEM;
+ }
+
+ priv->port_write_msg.err_count = 0;
+ priv->port_write_msg.discard_count = 0;
+
+ /* Point dequeue/enqueue pointers at first entry */
+ out_be32(&rmu->msg_regs->epwqbar, 0);
+ out_be32(&rmu->msg_regs->pwqbar, (u32) priv->port_write_msg.phys);
+
+ pr_debug("EIPWQBAR: 0x%08x IPWQBAR: 0x%08x\n",
+ in_be32(&rmu->msg_regs->epwqbar),
+ in_be32(&rmu->msg_regs->pwqbar));
+
+ /* Clear interrupt status IPWSR */
+ out_be32(&rmu->msg_regs->pwsr,
+ (RIO_IPWSR_TE | RIO_IPWSR_QFI | RIO_IPWSR_PWD));
+
+ /* Configure port write contoller for snooping enable all reporting,
+ clear queue full */
+ out_be32(&rmu->msg_regs->pwmr,
+ RIO_IPWMR_SEN | RIO_IPWMR_QFIE | RIO_IPWMR_EIE | RIO_IPWMR_CQ);
+
+
+ /* Hook up port-write handler */
+ rc = request_irq(IRQ_RIO_PW(mport), fsl_rio_port_write_handler,
+ IRQF_SHARED, "port-write", (void *)mport);
+ if (rc < 0) {
+ pr_err("MPC85xx RIO: unable to request inbound doorbell irq");
+ goto err_out;
+ }
+ /* Enable Error Interrupt */
+ out_be32((u32 *)(rio_regs_win + RIO_LTLEECSR), LTLEECSR_ENABLE_ALL);
+
+ INIT_WORK(&priv->pw_work, fsl_pw_dpc);
+ spin_lock_init(&priv->pw_fifo_lock);
+ if (kfifo_alloc(&priv->pw_fifo, RIO_PW_MSG_SIZE * 32, GFP_KERNEL)) {
+ pr_err("FIFO allocation failed\n");
+ rc = -ENOMEM;
+ goto err_out_irq;
+ }
+
+ pr_debug("IPWMR: 0x%08x IPWSR: 0x%08x\n",
+ in_be32(&rmu->msg_regs->pwmr),
+ in_be32(&rmu->msg_regs->pwsr));
+
+ return rc;
+
+err_out_irq:
+ free_irq(IRQ_RIO_PW(mport), (void *)mport);
+err_out:
+ dma_free_coherent(priv->dev, RIO_PW_MSG_SIZE,
+ priv->port_write_msg.virt,
+ priv->port_write_msg.phys);
+ return rc;
+}
+
+/**
+ * fsl_rio_doorbell_send - Send a MPC85xx doorbell message
+ * @mport: RapidIO master port info
+ * @index: ID of RapidIO interface
+ * @destid: Destination ID of target device
+ * @data: 16-bit info field of RapidIO doorbell message
+ *
+ * Sends a MPC85xx doorbell message. Returns %0 on success or
+ * %-EINVAL on failure.
+ */
+static int fsl_rio_doorbell_send(struct rio_mport *mport,
+ int index, u16 destid, u16 data)
+{
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
+
+ pr_debug("fsl_doorbell_send: index %d destid %4.4x data %4.4x\n",
+ index, destid, data);
+ switch (mport->phy_type) {
+ case RIO_PHY_PARALLEL:
+ out_be32(&rmu->dbell_atmu_regs->rowtar, destid << 22);
+ out_be16(rmu->dbell_win, data);
+ break;
+ case RIO_PHY_SERIAL:
+ /* In the serial version silicons, such as MPC8548, MPC8641,
+ * below operations is must be.
+ */
+ out_be32(&rmu->msg_regs->odmr, 0x00000000);
+ out_be32(&rmu->msg_regs->odretcr, 0x00000004);
+ out_be32(&rmu->msg_regs->oddpr, destid << 16);
+ out_be32(&rmu->msg_regs->oddatr, data);
+ out_be32(&rmu->msg_regs->odmr, 0x00000001);
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * fsl_add_outb_message - Add message to the MPC85xx outbound message queue
+ * @mport: Master port with outbound message queue
+ * @rdev: Target of outbound message
+ * @mbox: Outbound mailbox
+ * @buffer: Message to add to outbound queue
+ * @len: Length of message
+ *
+ * Adds the @buffer message to the MPC85xx outbound message queue. Returns
+ * %0 on success or %-EINVAL on failure.
+ */
+static int
+fsl_add_outb_message(struct rio_mport *mport, struct rio_dev *rdev, int mbox,
+ void *buffer, size_t len)
+{
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
+ u32 omr;
+ struct rio_tx_desc *desc = (struct rio_tx_desc *)rmu->msg_tx_ring.virt
+ + rmu->msg_tx_ring.tx_slot;
+ int ret = 0;
+
+ pr_debug("RIO: fsl_add_outb_message(): destid %4.4x mbox %d buffer " \
+ "%8.8x len %8.8x\n", rdev->destid, mbox, (int)buffer, len);
+
+ if ((len < 8) || (len > RIO_MAX_MSG_SIZE)) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ /* Copy and clear rest of buffer */
+ memcpy(rmu->msg_tx_ring.virt_buffer[rmu->msg_tx_ring.tx_slot], buffer,
+ len);
+ if (len < (RIO_MAX_MSG_SIZE - 4))
+ memset(rmu->msg_tx_ring.virt_buffer[rmu->msg_tx_ring.tx_slot]
+ + len, 0, RIO_MAX_MSG_SIZE - len);
+
+ switch (mport->phy_type) {
+ case RIO_PHY_PARALLEL:
+ /* Set mbox field for message */
+ desc->dport = mbox & 0x3;
+
+ /* Enable EOMI interrupt, set priority, and set destid */
+ desc->dattr = 0x28000000 | (rdev->destid << 2);
+ break;
+ case RIO_PHY_SERIAL:
+ /* Set mbox field for message, and set destid */
+ desc->dport = (rdev->destid << 16) | (mbox & 0x3);
+
+ /* Enable EOMI interrupt and priority */
+ desc->dattr = 0x28000000;
+ break;
+ }
+
+ /* Set transfer size aligned to next power of 2 (in double words) */
+ desc->dwcnt = is_power_of_2(len) ? len : 1 << get_bitmask_order(len);
+
+ /* Set snooping and source buffer address */
+ desc->saddr = 0x00000004
+ | rmu->msg_tx_ring.phys_buffer[rmu->msg_tx_ring.tx_slot];
+
+ /* Increment enqueue pointer */
+ omr = in_be32(&rmu->msg_regs->omr);
+ out_be32(&rmu->msg_regs->omr, omr | RIO_MSG_OMR_MUI);
+
+ /* Go to next descriptor */
+ if (++rmu->msg_tx_ring.tx_slot == rmu->msg_tx_ring.size)
+ rmu->msg_tx_ring.tx_slot = 0;
+
+out:
+ return ret;
+}
+
+/**
+ * fsl_open_outb_mbox - Initialize MPC85xx outbound mailbox
+ * @mport: Master port implementing the outbound message unit
+ * @dev_id: Device specific pointer to pass on event
+ * @mbox: Mailbox to open
+ * @entries: Number of entries in the outbound mailbox ring
+ *
+ * Initializes buffer ring, request the outbound message interrupt,
+ * and enables the outbound message unit. Returns %0 on success and
+ * %-EINVAL or %-ENOMEM on failure.
+ */
+static int
+fsl_open_outb_mbox(struct rio_mport *mport, void *dev_id, int mbox, int entries)
+{
+ int i, j, rc = 0;
+ struct rio_priv *priv = mport->priv;
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
+
+ if ((entries < RIO_MIN_TX_RING_SIZE) ||
+ (entries > RIO_MAX_TX_RING_SIZE) || (!is_power_of_2(entries))) {
+ rc = -EINVAL;
+ goto out;
+ }
+
+ /* Initialize shadow copy ring */
+ rmu->msg_tx_ring.dev_id = dev_id;
+ rmu->msg_tx_ring.size = entries;
+
+ for (i = 0; i < rmu->msg_tx_ring.size; i++) {
+ rmu->msg_tx_ring.virt_buffer[i] =
+ dma_alloc_coherent(priv->dev, RIO_MSG_BUFFER_SIZE,
+ &rmu->msg_tx_ring.phys_buffer[i], GFP_KERNEL);
+ if (!rmu->msg_tx_ring.virt_buffer[i]) {
+ rc = -ENOMEM;
+ for (j = 0; j < rmu->msg_tx_ring.size; j++)
+ if (rmu->msg_tx_ring.virt_buffer[j])
+ dma_free_coherent(priv->dev,
+ RIO_MSG_BUFFER_SIZE,
+ rmu->msg_tx_ring.
+ virt_buffer[j],
+ rmu->msg_tx_ring.
+ phys_buffer[j]);
+ goto out;
+ }
+ }
+
+ /* Initialize outbound message descriptor ring */
+ rmu->msg_tx_ring.virt = dma_alloc_coherent(priv->dev,
+ rmu->msg_tx_ring.size * RIO_MSG_DESC_SIZE,
+ &rmu->msg_tx_ring.phys, GFP_KERNEL);
+ if (!rmu->msg_tx_ring.virt) {
+ rc = -ENOMEM;
+ goto out_dma;
+ }
+ memset(rmu->msg_tx_ring.virt, 0,
+ rmu->msg_tx_ring.size * RIO_MSG_DESC_SIZE);
+ rmu->msg_tx_ring.tx_slot = 0;
+
+ /* Point dequeue/enqueue pointers at first entry in ring */
+ out_be32(&rmu->msg_regs->odqdpar, rmu->msg_tx_ring.phys);
+ out_be32(&rmu->msg_regs->odqepar, rmu->msg_tx_ring.phys);
+
+ /* Configure for snooping */
+ out_be32(&rmu->msg_regs->osar, 0x00000004);
+
+ /* Clear interrupt status */
+ out_be32(&rmu->msg_regs->osr, 0x000000b3);
+
+ /* Hook up outbound message handler */
+ rc = request_irq(IRQ_RIO_TX(mport), fsl_rio_tx_handler, 0,
+ "msg_tx", (void *)mport);
+ if (rc < 0)
+ goto out_irq;
+
+ /*
+ * Configure outbound message unit
+ * Snooping
+ * Interrupts (all enabled, except QEIE)
+ * Chaining mode
+ * Disable
+ */
+ out_be32(&rmu->msg_regs->omr, 0x00100220);
+
+ /* Set number of entries */
+ out_be32(&rmu->msg_regs->omr,
+ in_be32(&rmu->msg_regs->omr) |
+ ((get_bitmask_order(entries) - 2) << 12));
+
+ /* Now enable the unit */
+ out_be32(&rmu->msg_regs->omr, in_be32(&rmu->msg_regs->omr) | 0x1);
+
+out:
+ return rc;
+
+out_irq:
+ dma_free_coherent(priv->dev,
+ rmu->msg_tx_ring.size * RIO_MSG_DESC_SIZE,
+ rmu->msg_tx_ring.virt, rmu->msg_tx_ring.phys);
+
+out_dma:
+ for (i = 0; i < rmu->msg_tx_ring.size; i++)
+ dma_free_coherent(priv->dev, RIO_MSG_BUFFER_SIZE,
+ rmu->msg_tx_ring.virt_buffer[i],
+ rmu->msg_tx_ring.phys_buffer[i]);
+
+ return rc;
+}
+
+/**
+ * fsl_close_outb_mbox - Shut down MPC85xx outbound mailbox
+ * @mport: Master port implementing the outbound message unit
+ * @mbox: Mailbox to close
+ *
+ * Disables the outbound message unit, free all buffers, and
+ * frees the outbound message interrupt.
+ */
+static void fsl_close_outb_mbox(struct rio_mport *mport, int mbox)
+{
+ struct rio_priv *priv = mport->priv;
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
+
+ /* Disable inbound message unit */
+ out_be32(&rmu->msg_regs->omr, 0);
+
+ /* Free ring */
+ dma_free_coherent(priv->dev,
+ rmu->msg_tx_ring.size * RIO_MSG_DESC_SIZE,
+ rmu->msg_tx_ring.virt, rmu->msg_tx_ring.phys);
+
+ /* Free interrupt */
+ free_irq(IRQ_RIO_TX(mport), (void *)mport);
+}
+
+/**
+ * fsl_open_inb_mbox - Initialize MPC85xx inbound mailbox
+ * @mport: Master port implementing the inbound message unit
+ * @dev_id: Device specific pointer to pass on event
+ * @mbox: Mailbox to open
+ * @entries: Number of entries in the inbound mailbox ring
+ *
+ * Initializes buffer ring, request the inbound message interrupt,
+ * and enables the inbound message unit. Returns %0 on success
+ * and %-EINVAL or %-ENOMEM on failure.
+ */
+static int
+fsl_open_inb_mbox(struct rio_mport *mport, void *dev_id, int mbox, int entries)
+{
+ int i, rc = 0;
+ struct rio_priv *priv = mport->priv;
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
+
+ if ((entries < RIO_MIN_RX_RING_SIZE) ||
+ (entries > RIO_MAX_RX_RING_SIZE) || (!is_power_of_2(entries))) {
+ rc = -EINVAL;
+ goto out;
+ }
+
+ /* Initialize client buffer ring */
+ rmu->msg_rx_ring.dev_id = dev_id;
+ rmu->msg_rx_ring.size = entries;
+ rmu->msg_rx_ring.rx_slot = 0;
+ for (i = 0; i < rmu->msg_rx_ring.size; i++)
+ rmu->msg_rx_ring.virt_buffer[i] = NULL;
+
+ /* Initialize inbound message ring */
+ rmu->msg_rx_ring.virt = dma_alloc_coherent(priv->dev,
+ rmu->msg_rx_ring.size * RIO_MAX_MSG_SIZE,
+ &rmu->msg_rx_ring.phys, GFP_KERNEL);
+ if (!rmu->msg_rx_ring.virt) {
+ rc = -ENOMEM;
+ goto out;
+ }
+
+ /* Point dequeue/enqueue pointers at first entry in ring */
+ out_be32(&rmu->msg_regs->ifqdpar, (u32) rmu->msg_rx_ring.phys);
+ out_be32(&rmu->msg_regs->ifqepar, (u32) rmu->msg_rx_ring.phys);
+
+ /* Clear interrupt status */
+ out_be32(&rmu->msg_regs->isr, 0x00000091);
+
+ /* Hook up inbound message handler */
+ rc = request_irq(IRQ_RIO_RX(mport), fsl_rio_rx_handler, 0,
+ "msg_rx", (void *)mport);
+ if (rc < 0) {
+ dma_free_coherent(priv->dev, RIO_MSG_BUFFER_SIZE,
+ rmu->msg_tx_ring.virt_buffer[i],
+ rmu->msg_tx_ring.phys_buffer[i]);
+ goto out;
+ }
+
+ /*
+ * Configure inbound message unit:
+ * Snooping
+ * 4KB max message size
+ * Unmask all interrupt sources
+ * Disable
+ */
+ out_be32(&rmu->msg_regs->imr, 0x001b0060);
+
+ /* Set number of queue entries */
+ setbits32(&rmu->msg_regs->imr, (get_bitmask_order(entries) - 2) << 12);
+
+ /* Now enable the unit */
+ setbits32(&rmu->msg_regs->imr, 0x1);
+
+out:
+ return rc;
+}
+
+/**
+ * fsl_close_inb_mbox - Shut down MPC85xx inbound mailbox
+ * @mport: Master port implementing the inbound message unit
+ * @mbox: Mailbox to close
+ *
+ * Disables the inbound message unit, free all buffers, and
+ * frees the inbound message interrupt.
+ */
+static void fsl_close_inb_mbox(struct rio_mport *mport, int mbox)
+{
+ struct rio_priv *priv = mport->priv;
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
+
+ /* Disable inbound message unit */
+ out_be32(&rmu->msg_regs->imr, 0);
+
+ /* Free ring */
+ dma_free_coherent(priv->dev, rmu->msg_rx_ring.size * RIO_MAX_MSG_SIZE,
+ rmu->msg_rx_ring.virt, rmu->msg_rx_ring.phys);
+
+ /* Free interrupt */
+ free_irq(IRQ_RIO_RX(mport), (void *)mport);
+}
+
+/**
+ * fsl_add_inb_buffer - Add buffer to the MPC85xx inbound message queue
+ * @mport: Master port implementing the inbound message unit
+ * @mbox: Inbound mailbox number
+ * @buf: Buffer to add to inbound queue
+ *
+ * Adds the @buf buffer to the MPC85xx inbound message queue. Returns
+ * %0 on success or %-EINVAL on failure.
+ */
+static int fsl_add_inb_buffer(struct rio_mport *mport, int mbox, void *buf)
+{
+ int rc = 0;
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
+
+ pr_debug("RIO: fsl_add_inb_buffer(), msg_rx_ring.rx_slot %d\n",
+ rmu->msg_rx_ring.rx_slot);
+
+ if (rmu->msg_rx_ring.virt_buffer[rmu->msg_rx_ring.rx_slot]) {
+ printk(KERN_ERR
+ "RIO: error adding inbound buffer %d, buffer exists\n",
+ rmu->msg_rx_ring.rx_slot);
+ rc = -EINVAL;
+ goto out;
+ }
+
+ rmu->msg_rx_ring.virt_buffer[rmu->msg_rx_ring.rx_slot] = buf;
+ if (++rmu->msg_rx_ring.rx_slot == rmu->msg_rx_ring.size)
+ rmu->msg_rx_ring.rx_slot = 0;
+
+out:
+ return rc;
+}
+
+/**
+ * fsl_get_inb_message - Fetch inbound message from the MPC85xx message unit
+ * @mport: Master port implementing the inbound message unit
+ * @mbox: Inbound mailbox number
+ *
+ * Gets the next available inbound message from the inbound message queue.
+ * A pointer to the message is returned on success or NULL on failure.
+ */
+static void *fsl_get_inb_message(struct rio_mport *mport, int mbox)
+{
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
+ u32 phys_buf, virt_buf;
+ void *buf = NULL;
+ int buf_idx;
+
+ phys_buf = in_be32(&rmu->msg_regs->ifqdpar);
+
+ /* If no more messages, then bail out */
+ if (phys_buf == in_be32(&rmu->msg_regs->ifqepar))
+ goto out2;
+
+ virt_buf = (u32) rmu->msg_rx_ring.virt + (phys_buf
+ - rmu->msg_rx_ring.phys);
+ buf_idx = (phys_buf - rmu->msg_rx_ring.phys) / RIO_MAX_MSG_SIZE;
+ buf = rmu->msg_rx_ring.virt_buffer[buf_idx];
+
+ if (!buf) {
+ printk(KERN_ERR
+ "RIO: inbound message copy failed, no buffers\n");
+ goto out1;
+ }
+
+ /* Copy max message size, caller is expected to allocate that big */
+ memcpy(buf, (void *)virt_buf, RIO_MAX_MSG_SIZE);
+
+ /* Clear the available buffer */
+ rmu->msg_rx_ring.virt_buffer[buf_idx] = NULL;
+
+out1:
+ setbits32(&rmu->msg_regs->imr, RIO_MSG_IMR_MI);
+
+out2:
+ return buf;
+}
+
+/**
+ * fsl_rio_doorbell_init - MPC85xx doorbell interface init
+ * @mport: Master port implementing the inbound doorbell unit
+ *
+ * Initializes doorbell unit hardware and inbound DMA buffer
+ * ring. Called from fsl_rio_setup(). Returns %0 on success
+ * or %-ENOMEM on failure.
+ */
+static int fsl_rio_doorbell_init(struct rio_mport *mport)
+{
+ struct rio_priv *priv = mport->priv;
+ struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
+ int rc = 0;
+
+ /* Map outbound doorbell window immediately after maintenance window */
+ rmu->dbell_win = ioremap(mport->iores.start + RIO_MAINT_WIN_SIZE,
+ RIO_DBELL_WIN_SIZE);
+ if (!rmu->dbell_win) {
+ printk(KERN_ERR
+ "RIO: unable to map outbound doorbell window\n");
+ rc = -ENOMEM;
+ goto out;
+ }
+
+ /* Initialize inbound doorbells */
+ rmu->dbell_ring.virt = dma_alloc_coherent(priv->dev, 512 *
+ DOORBELL_MESSAGE_SIZE, &rmu->dbell_ring.phys, GFP_KERNEL);
+ if (!rmu->dbell_ring.virt) {
+ printk(KERN_ERR "RIO: unable allocate inbound doorbell ring\n");
+ rc = -ENOMEM;
+ iounmap(rmu->dbell_win);
+ goto out;
+ }
+
+ /* Point dequeue/enqueue pointers at first entry in ring */
+ out_be32(&rmu->msg_regs->dqdpar, (u32) rmu->dbell_ring.phys);
+ out_be32(&rmu->msg_regs->dqepar, (u32) rmu->dbell_ring.phys);
+
+ /* Clear interrupt status */
+ out_be32(&rmu->msg_regs->dsr, 0x00000091);
+
+ /* Hook up doorbell handler */
+ rc = request_irq(IRQ_RIO_BELL(mport), fsl_rio_dbell_handler, 0,
+ "dbell_rx", (void *)mport);
+ if (rc < 0) {
+ iounmap(rmu->dbell_win);
+ dma_free_coherent(priv->dev, 512 * DOORBELL_MESSAGE_SIZE,
+ rmu->dbell_ring.virt, rmu->dbell_ring.phys);
+ printk(KERN_ERR
+ "MPC85xx RIO: unable to request inbound doorbell irq");
+ goto out;
+ }
+
+ /* Configure doorbells for snooping, 512 entries, and enable */
+ out_be32(&rmu->msg_regs->dmr, 0x00108161);
+
+out:
+ return rc;
+}
+
+int fsl_rio_setup_rmu(struct rio_mport *mport, struct device_node *node)
+{
+ struct rio_priv *priv;
+ struct fsl_rmu *rmu;
+ struct rio_ops *ops;
+
+ if (!mport || !mport->priv || !node)
+ return -1;
+
+ rmu = kzalloc(sizeof(struct fsl_rmu), GFP_KERNEL);
+ if (!rmu)
+ return -ENOMEM;
+
+ priv = mport->priv;
+ priv->rmm_handle = rmu;
+ rmu->dbell_atmu_regs = priv->atmu_regs + 2;
+ rmu->msg_regs = (struct rio_msg_regs *)(priv->regs_win +
+ ((mport->phy_type == RIO_PHY_SERIAL) ?
+ RIO_S_MSG_REGS_OFFSET : RIO_P_MSG_REGS_OFFSET));
+
+ rmu->bellirq = irq_of_parse_and_map(node, 2);
+ rmu->txirq = irq_of_parse_and_map(node, 3);
+ rmu->rxirq = irq_of_parse_and_map(node, 4);
+ dev_info(priv->dev, "bellirq: %d, txirq: %d, rxirq %d\n",
+ rmu->bellirq, rmu->txirq, rmu->rxirq);
+
+ ops = mport->ops;
+
+ ops->dsend = fsl_rio_doorbell_send;
+ ops->open_outb_mbox = fsl_open_outb_mbox;
+ ops->open_inb_mbox = fsl_open_inb_mbox;
+ ops->close_outb_mbox = fsl_close_outb_mbox;
+ ops->close_inb_mbox = fsl_close_inb_mbox;
+ ops->add_outb_message = fsl_add_outb_message;
+ ops->add_inb_buffer = fsl_add_inb_buffer;
+ ops->get_inb_message = fsl_get_inb_message;
+
+ rio_init_dbell_res(&mport->riores[RIO_DOORBELL_RESOURCE], 0, 0xffff);
+ rio_init_mbox_res(&mport->riores[RIO_INB_MBOX_RESOURCE], 0, 0);
+ rio_init_mbox_res(&mport->riores[RIO_OUTB_MBOX_RESOURCE], 0, 0);
+
+ /* Configure outbound doorbell window */
+ out_be32(&rmu->dbell_atmu_regs->rowbar,
+ (mport->iores.start + RIO_MAINT_WIN_SIZE) >> 12);
+ /* 4k window size */
+ out_be32(&rmu->dbell_atmu_regs->rowar, 0x8004200b);
+
+ fsl_rio_doorbell_init(mport);
+
+ return 0;
+}
--
1.7.3.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message units support
2011-11-12 12:02 [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Liu Gang
@ 2011-11-12 12:02 ` Liu Gang
2011-11-16 13:39 ` Bounine, Alexandre
2011-11-12 12:02 ` [PATCH 3/5,v3] powerpc/85xx: Update SRIO device tree nodes Liu Gang
` (3 subsequent siblings)
4 siblings, 1 reply; 18+ messages in thread
From: Liu Gang @ 2011-11-12 12:02 UTC (permalink / raw)
To: linuxppc-dev, Alexandre.Bounine
Cc: Jin Qing, r58472, r61911, linux-kernel, Liu Gang, akpm, B11780
Usually, freescale rapidio endpoint can support one or two 1x or 4X
LP-Serial link interfaces, and rapidio message transactions can be
implemented by two message units. This adds the support of two
rapidio ports and initializes message unit 0 and message unit 1. And
these ports and message units can work simultaneously.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/sysdev/fsl_rio.c | 391 +++++++++++++++++++++-----------
arch/powerpc/sysdev/fsl_rio.h | 75 ++++++-
arch/powerpc/sysdev/fsl_rmu.c | 502 ++++++++++++++++++-----------------------
3 files changed, 545 insertions(+), 423 deletions(-)
diff --git a/arch/powerpc/sysdev/fsl_rio.c b/arch/powerpc/sysdev/fsl_rio.c
index 9484484..a4c4f4a 100644
--- a/arch/powerpc/sysdev/fsl_rio.c
+++ b/arch/powerpc/sysdev/fsl_rio.c
@@ -45,7 +45,6 @@
#define RIO_PORT1_IECSR 0x10130
#define RIO_PORT2_IECSR 0x101B0
-#define RIO_ATMU_REGS_OFFSET 0x10c00
#define RIO_GCCSR 0x13c
#define RIO_ESCSR 0x158
#define ESCSR_CLEAR 0x07120204
@@ -74,6 +73,11 @@
: "b" (addr), "i" (-EFAULT), "0" (err))
void __iomem *rio_regs_win;
+void __iomem *rmu_regs_win;
+resource_size_t rio_law_start;
+
+struct fsl_rio_dbell *dbell;
+struct fsl_rio_pw *pw;
#ifdef CONFIG_E500
int fsl_rio_mcheck_exception(struct pt_regs *regs)
@@ -120,7 +124,7 @@ static int fsl_local_config_read(struct rio_mport *mport,
{
struct rio_priv *priv = mport->priv;
pr_debug("fsl_local_config_read: index %d offset %8.8x\n", index,
- offset);
+ offset);
*data = in_be32(priv->regs_win + offset);
return 0;
@@ -173,7 +177,7 @@ fsl_rio_config_read(struct rio_mport *mport, int index, u16 destid,
pr_debug
("fsl_rio_config_read:"
" index %d destid %d hopcount %d offset %8.8x len %d\n",
- index, destid, hopcount, offset, len);
+ index, destid, hopcount, offset, len);
/* 16MB maintenance window possible */
/* allow only aligned access to maintenance registers */
@@ -230,8 +234,8 @@ fsl_rio_config_write(struct rio_mport *mport, int index, u16 destid,
u8 *data;
pr_debug
("fsl_rio_config_write:"
- "index %d destid %d hopcount %d offset %8.8x len %d val %8.8x\n",
- index, destid, hopcount, offset, len, val);
+ " index %d destid %d hopcount %d offset %8.8x len %d val %8.8x\n",
+ index, destid, hopcount, offset, len, val);
/* 16MB maintenance windows possible */
/* allow only aligned access to maintenance registers */
@@ -260,7 +264,7 @@ fsl_rio_config_write(struct rio_mport *mport, int index, u16 destid,
return 0;
}
-void fsl_rio_port_error_handler(struct rio_mport *port, int offset)
+void fsl_rio_port_error_handler(int offset)
{
/*XXX: Error recovery is not implemented, we just clear errors */
out_be32((u32 *)(rio_regs_win + RIO_LTLEDCSR), 0);
@@ -331,16 +335,21 @@ int fsl_rio_setup(struct platform_device *dev)
struct rio_mport *port;
struct rio_priv *priv;
int rc = 0;
- const u32 *dt_range, *cell;
- struct resource regs;
+ const u32 *dt_range, *cell, *port_index;
+ u32 active_ports = 0;
+ struct resource regs, rmu_regs;
+ struct device_node *np, *rmu_node;
int rlen;
u32 ccsr;
- u64 law_start, law_size;
+ u64 range_start, range_size;
int paw, aw, sw;
+ u32 i;
+ static int tmp;
+ struct device_node *rmu_np[MAX_MSG_UNIT_NUM] = {NULL};
if (!dev->dev.of_node) {
dev_err(&dev->dev, "Device OF-Node is NULL");
- return -EFAULT;
+ return -ENODEV;
}
rc = of_address_to_resource(dev->dev.of_node, 0, ®s);
@@ -353,34 +362,13 @@ int fsl_rio_setup(struct platform_device *dev)
dev->dev.of_node->full_name);
dev_info(&dev->dev, "Regs: %pR\n", ®s);
- dt_range = of_get_property(dev->dev.of_node, "ranges", &rlen);
- if (!dt_range) {
- dev_err(&dev->dev, "Can't get %s property 'ranges'\n",
- dev->dev.of_node->full_name);
- return -EFAULT;
+ rio_regs_win = ioremap(regs.start, resource_size(®s));
+ if (!rio_regs_win) {
+ dev_err(&dev->dev, "Unable to map rio register window\n");
+ rc = -ENOMEM;
+ goto err_rio_regs;
}
- /* Get node address wide */
- cell = of_get_property(dev->dev.of_node, "#address-cells", NULL);
- if (cell)
- aw = *cell;
- else
- aw = of_n_addr_cells(dev->dev.of_node);
- /* Get node size wide */
- cell = of_get_property(dev->dev.of_node, "#size-cells", NULL);
- if (cell)
- sw = *cell;
- else
- sw = of_n_size_cells(dev->dev.of_node);
- /* Get parent address wide wide */
- paw = of_n_addr_cells(dev->dev.of_node);
-
- law_start = of_read_number(dt_range + aw, paw);
- law_size = of_read_number(dt_range + aw + paw, sw);
-
- dev_info(&dev->dev, "LAW start 0x%016llx, size 0x%016llx.\n",
- law_start, law_size);
-
ops = kzalloc(sizeof(struct rio_ops), GFP_KERNEL);
if (!ops) {
rc = -ENOMEM;
@@ -390,130 +378,267 @@ int fsl_rio_setup(struct platform_device *dev)
ops->lcwrite = fsl_local_config_write;
ops->cread = fsl_rio_config_read;
ops->cwrite = fsl_rio_config_write;
+ ops->dsend = fsl_rio_doorbell_send;
ops->pwenable = fsl_rio_pw_enable;
-
- port = kzalloc(sizeof(struct rio_mport), GFP_KERNEL);
- if (!port) {
+ ops->open_outb_mbox = fsl_open_outb_mbox;
+ ops->open_inb_mbox = fsl_open_inb_mbox;
+ ops->close_outb_mbox = fsl_close_outb_mbox;
+ ops->close_inb_mbox = fsl_close_inb_mbox;
+ ops->add_outb_message = fsl_add_outb_message;
+ ops->add_inb_buffer = fsl_add_inb_buffer;
+ ops->get_inb_message = fsl_get_inb_message;
+
+ rmu_node = of_parse_phandle(dev->dev.of_node, "fsl,srio-rmu-handle", 0);
+ if (!rmu_node)
+ goto err_rmu;
+ rc = of_address_to_resource(rmu_node, 0, &rmu_regs);
+ if (rc) {
+ dev_err(&dev->dev, "Can't get %s property 'reg'\n",
+ rmu_node->full_name);
+ goto err_rmu;
+ }
+ rmu_regs_win = ioremap(rmu_regs.start, resource_size(&rmu_regs));
+ if (!rmu_regs_win) {
+ dev_err(&dev->dev, "Unable to map rmu register window\n");
rc = -ENOMEM;
- goto err_port;
+ goto err_rmu;
+ }
+ for_each_compatible_node(np, NULL, "fsl,srio-msg-unit") {
+ rmu_np[tmp] = np;
+ tmp++;
}
- port->index = 0;
- priv = kzalloc(sizeof(struct rio_priv), GFP_KERNEL);
- if (!priv) {
- printk(KERN_ERR "Can't alloc memory for 'priv'\n");
+ /*set up doobell node*/
+ np = of_find_compatible_node(NULL, NULL, "fsl,srio-dbell-unit");
+ if (!np) {
+ rc = -ENODEV;
+ goto err_dbell;
+ }
+ dbell = kzalloc(sizeof(struct fsl_rio_dbell), GFP_KERNEL);
+ if (!(dbell)) {
+ dev_err(&dev->dev, "Can't alloc memory for 'fsl_rio_dbell'\n");
rc = -ENOMEM;
- goto err_priv;
+ goto err_dbell;
}
+ dbell->dev = &dev->dev;
+ dbell->bellirq = irq_of_parse_and_map(np, 1);
+ dev_info(&dev->dev, "bellirq: %d\n", dbell->bellirq);
- INIT_LIST_HEAD(&port->dbells);
- port->iores.start = law_start;
- port->iores.end = law_start + law_size - 1;
- port->iores.flags = IORESOURCE_MEM;
- port->iores.name = "rio_io_win";
-
- if (request_resource(&iomem_resource, &port->iores) < 0) {
- dev_err(&dev->dev, "RIO: Error requesting master port region"
- " 0x%016llx-0x%016llx\n",
- (u64)port->iores.start, (u64)port->iores.end);
- rc = -ENOMEM;
- goto err_res;
+ aw = of_n_addr_cells(np);
+ dt_range = of_get_property(np, "reg", &rlen);
+ if (!dt_range) {
+ pr_err("%s: unable to find 'reg' property\n",
+ np->full_name);
+ rc = -ENOMEM;
+ goto err_pw;
+ }
+ range_start = of_read_number(dt_range, aw);
+ dbell->dbell_regs = (struct rio_dbell_regs *)(rmu_regs_win +
+ (u32)range_start);
+
+ /*set up port write node*/
+ np = of_find_compatible_node(NULL, NULL, "fsl,srio-port-write-unit");
+ if (!np) {
+ rc = -ENODEV;
+ goto err_pw;
+ }
+ pw = kzalloc(sizeof(struct fsl_rio_pw), GFP_KERNEL);
+ if (!(pw)) {
+ dev_err(&dev->dev, "Can't alloc memory for 'fsl_rio_pw'\n");
+ rc = -ENOMEM;
+ goto err_pw;
+ }
+ pw->dev = &dev->dev;
+ pw->pwirq = irq_of_parse_and_map(np, 0);
+ dev_info(&dev->dev, "pwirq: %d\n", pw->pwirq);
+ aw = of_n_addr_cells(np);
+ dt_range = of_get_property(np, "reg", &rlen);
+ if (!dt_range) {
+ pr_err("%s: unable to find 'reg' property\n",
+ np->full_name);
+ rc = -ENOMEM;
+ goto err;
}
+ range_start = of_read_number(dt_range, aw);
+ pw->pw_regs = (struct rio_pw_regs *)(rmu_regs_win + (u32)range_start);
+
+ /*set up ports node*/
+ for_each_child_of_node(dev->dev.of_node, np) {
+ port_index = of_get_property(np, "cell-index", NULL);
+ if (!port_index) {
+ dev_err(&dev->dev, "Can't get %s property 'cell-index'\n",
+ np->full_name);
+ continue;
+ }
+
+ dt_range = of_get_property(np, "ranges", &rlen);
+ if (!dt_range) {
+ dev_err(&dev->dev, "Can't get %s property 'ranges'\n",
+ np->full_name);
+ continue;
+ }
- priv->pwirq = irq_of_parse_and_map(dev->dev.of_node, 0);
- dev_info(&dev->dev, "pwirq: %d\n", priv->pwirq);
- strcpy(port->name, "RIO0 mport");
-
- priv->dev = &dev->dev;
-
- port->ops = ops;
- port->priv = priv;
- port->phys_efptr = 0x100;
-
- priv->regs_win = ioremap(regs.start, resource_size(®s));
- rio_regs_win = priv->regs_win;
-
- /* Probe the master port phy type */
- ccsr = in_be32(priv->regs_win + RIO_CCSR);
- port->phy_type = (ccsr & 1) ? RIO_PHY_SERIAL : RIO_PHY_PARALLEL;
- dev_info(&dev->dev, "RapidIO PHY type: %s\n",
- (port->phy_type == RIO_PHY_PARALLEL) ? "parallel" :
- ((port->phy_type == RIO_PHY_SERIAL) ? "serial" :
- "unknown"));
- /* Checking the port training status */
- if (in_be32((priv->regs_win + RIO_ESCSR)) & 1) {
- dev_err(&dev->dev, "Port is not ready. "
- "Try to restart connection...\n");
- switch (port->phy_type) {
- case RIO_PHY_SERIAL:
+ /* Get node address wide */
+ cell = of_get_property(np, "#address-cells", NULL);
+ if (cell)
+ aw = *cell;
+ else
+ aw = of_n_addr_cells(np);
+ /* Get node size wide */
+ cell = of_get_property(np, "#size-cells", NULL);
+ if (cell)
+ sw = *cell;
+ else
+ sw = of_n_size_cells(np);
+ /* Get parent address wide wide */
+ paw = of_n_addr_cells(np);
+ range_start = of_read_number(dt_range + aw, paw);
+ range_size = of_read_number(dt_range + aw + paw, sw);
+
+ dev_info(&dev->dev, "%s: LAW start 0x%016llx, size 0x%016llx.\n",
+ np->full_name, range_start, range_size);
+
+ port = kzalloc(sizeof(struct rio_mport), GFP_KERNEL);
+ if (!port)
+ continue;
+
+ i = *port_index - 1;
+ port->index = (unsigned char)i;
+
+ priv = kzalloc(sizeof(struct rio_priv), GFP_KERNEL);
+ if (!priv) {
+ dev_err(&dev->dev, "Can't alloc memory for 'priv'\n");
+ kfree(port);
+ continue;
+ }
+
+ INIT_LIST_HEAD(&port->dbells);
+ port->iores.start = range_start;
+ port->iores.end = port->iores.start + range_size - 1;
+ port->iores.flags = IORESOURCE_MEM;
+ port->iores.name = "rio_io_win";
+
+ if (request_resource(&iomem_resource, &port->iores) < 0) {
+ dev_err(&dev->dev, "RIO: Error requesting master port region"
+ " 0x%016llx-0x%016llx\n",
+ (u64)port->iores.start, (u64)port->iores.end);
+ kfree(priv);
+ kfree(port);
+ continue;
+ }
+ sprintf(port->name, "RIO mport %d", i);
+
+ priv->dev = &dev->dev;
+ port->ops = ops;
+ port->priv = priv;
+ port->phys_efptr = 0x100;
+ priv->regs_win = rio_regs_win;
+
+ /* Probe the master port phy type */
+ ccsr = in_be32(priv->regs_win + RIO_CCSR + i*0x20);
+ port->phy_type = (ccsr & 1) ? RIO_PHY_SERIAL : RIO_PHY_PARALLEL;
+ if (port->phy_type == RIO_PHY_PARALLEL) {
+ dev_err(&dev->dev, "RIO: Parallel PHY type, unsupported port type!\n");
+ release_resource(&port->iores);
+ kfree(priv);
+ kfree(port);
+ continue;
+ }
+ dev_info(&dev->dev, "RapidIO PHY type: Serial\n");
+ /* Checking the port training status */
+ if (in_be32((priv->regs_win + RIO_ESCSR + i*0x20)) & 1) {
+ dev_err(&dev->dev, "Port %d is not ready. "
+ "Try to restart connection...\n", i);
/* Disable ports */
- out_be32(priv->regs_win + RIO_CCSR, 0);
+ out_be32(priv->regs_win
+ + RIO_CCSR + i*0x20, 0);
/* Set 1x lane */
- setbits32(priv->regs_win + RIO_CCSR, 0x02000000);
+ setbits32(priv->regs_win
+ + RIO_CCSR + i*0x20, 0x02000000);
/* Enable ports */
- setbits32(priv->regs_win + RIO_CCSR, 0x00600000);
- break;
- case RIO_PHY_PARALLEL:
- /* Disable ports */
- out_be32(priv->regs_win + RIO_CCSR, 0x22000000);
- /* Enable ports */
- out_be32(priv->regs_win + RIO_CCSR, 0x44000000);
- break;
+ setbits32(priv->regs_win
+ + RIO_CCSR + i*0x20, 0x00600000);
+ msleep(100);
+ if (in_be32((priv->regs_win
+ + RIO_ESCSR + i*0x20)) & 1) {
+ dev_err(&dev->dev,
+ "Port %d restart failed.\n", i);
+ release_resource(&port->iores);
+ kfree(priv);
+ kfree(port);
+ continue;
+ }
+ dev_info(&dev->dev, "Port %d restart success!\n", i);
}
- msleep(100);
- if (in_be32((priv->regs_win + RIO_ESCSR)) & 1) {
- dev_err(&dev->dev, "Port restart failed.\n");
- rc = -ENOLINK;
- goto err;
- }
- dev_info(&dev->dev, "Port restart success!\n");
- }
- fsl_rio_info(&dev->dev, ccsr);
+ fsl_rio_info(&dev->dev, ccsr);
- port->sys_size = (in_be32((priv->regs_win + RIO_PEF_CAR))
+ port->sys_size = (in_be32((priv->regs_win + RIO_PEF_CAR))
& RIO_PEF_CTLS) >> 4;
- dev_info(&dev->dev, "RapidIO Common Transport System size: %d\n",
- port->sys_size ? 65536 : 256);
+ dev_info(&dev->dev, "RapidIO Common Transport System size: %d\n",
+ port->sys_size ? 65536 : 256);
+
+ if (rio_register_mport(port)) {
+ release_resource(&port->iores);
+ kfree(priv);
+ kfree(port);
+ continue;
+ }
+ if (port->host_deviceid >= 0)
+ out_be32(priv->regs_win + RIO_GCCSR, RIO_PORT_GEN_HOST |
+ RIO_PORT_GEN_MASTER | RIO_PORT_GEN_DISCOVERED);
+ else
+ out_be32(priv->regs_win + RIO_GCCSR,
+ RIO_PORT_GEN_MASTER);
- if (rio_register_mport(port))
- goto err;
+ priv->atmu_regs = (struct rio_atmu_regs *)(priv->regs_win
+ + ((i == 0) ? RIO_ATMU_REGS_PORT1_OFFSET :
+ RIO_ATMU_REGS_PORT2_OFFSET));
+
+ priv->maint_atmu_regs = priv->atmu_regs + 1;
- if (port->host_deviceid >= 0)
- out_be32(priv->regs_win + RIO_GCCSR, RIO_PORT_GEN_HOST |
- RIO_PORT_GEN_MASTER | RIO_PORT_GEN_DISCOVERED);
- else
- out_be32(priv->regs_win + RIO_GCCSR, 0x00000000);
+ /* Set to receive any dist ID for serial RapidIO controller. */
+ if (port->phy_type == RIO_PHY_SERIAL)
+ out_be32((priv->regs_win
+ + RIO_ISR_AACR + i*0x80), RIO_ISR_AACR_AA);
- priv->atmu_regs = (struct rio_atmu_regs *)(priv->regs_win
- + RIO_ATMU_REGS_OFFSET);
- priv->maint_atmu_regs = priv->atmu_regs + 1;
+ /* Configure maintenance transaction window */
+ out_be32(&priv->maint_atmu_regs->rowbar,
+ port->iores.start >> 12);
+ out_be32(&priv->maint_atmu_regs->rowar,
+ 0x80077000 | (ilog2(RIO_MAINT_WIN_SIZE) - 1));
- /* Set to receive any dist ID for serial RapidIO controller. */
- if (port->phy_type == RIO_PHY_SERIAL)
- out_be32((priv->regs_win + RIO_ISR_AACR), RIO_ISR_AACR_AA);
+ priv->maint_win = ioremap(port->iores.start,
+ RIO_MAINT_WIN_SIZE);
- /* Configure maintenance transaction window */
- out_be32(&priv->maint_atmu_regs->rowbar, law_start >> 12);
- out_be32(&priv->maint_atmu_regs->rowar,
- 0x80077000 | (ilog2(RIO_MAINT_WIN_SIZE) - 1));
+ rio_law_start = range_start;
- priv->maint_win = ioremap(law_start, RIO_MAINT_WIN_SIZE);
+ fsl_rio_setup_rmu(port, rmu_np[i]);
- fsl_rio_setup_rmu(port, dev->dev.of_node);
+ dbell->mport[i] = port;
+
+ active_ports++;
+ }
+
+ if (!active_ports) {
+ rc = -ENOLINK;
+ goto err;
+ }
- fsl_rio_port_write_init(port);
+ fsl_rio_doorbell_init(dbell);
+ fsl_rio_port_write_init(pw);
return 0;
err:
- iounmap(priv->regs_win);
- release_resource(&port->iores);
-err_res:
- kfree(priv);
-err_priv:
- kfree(port);
-err_port:
+ kfree(pw);
+err_pw:
+ kfree(dbell);
+err_dbell:
+ iounmap(rmu_regs_win);
+err_rmu:
kfree(ops);
err_ops:
+ iounmap(rio_regs_win);
+err_rio_regs:
return rc;
}
@@ -529,7 +654,7 @@ static int __devinit fsl_of_rio_rpn_probe(struct platform_device *dev)
static const struct of_device_id fsl_of_rio_rpn_ids[] = {
{
- .compatible = "fsl,rapidio-delta",
+ .compatible = "fsl,srio",
},
{},
};
diff --git a/arch/powerpc/sysdev/fsl_rio.h b/arch/powerpc/sysdev/fsl_rio.h
index f888a1e..ae8e274 100644
--- a/arch/powerpc/sysdev/fsl_rio.h
+++ b/arch/powerpc/sysdev/fsl_rio.h
@@ -36,13 +36,36 @@
#define RIO_MAINT_WIN_SIZE 0x400000
#define RIO_LTLEDCSR 0x0608
+#define DOORBELL_ROWAR_EN 0x80000000
+#define DOORBELL_ROWAR_TFLOWLV 0x08000000 /* highest priority level */
+#define DOORBELL_ROWAR_PCI 0x02000000 /* PCI window */
+#define DOORBELL_ROWAR_NREAD 0x00040000 /* NREAD */
+#define DOORBELL_ROWAR_MAINTRD 0x00070000 /* maintenance read */
+#define DOORBELL_ROWAR_RES 0x00002000 /* wrtpy: reserverd */
+#define DOORBELL_ROWAR_MAINTWD 0x00007000
+#define DOORBELL_ROWAR_SIZE 0x0000000b /* window size is 4k */
+
+#define RIO_ATMU_REGS_PORT1_OFFSET 0x10c00
+#define RIO_ATMU_REGS_PORT2_OFFSET 0x10e00
+#define RIO_S_DBELL_REGS_OFFSET 0x13400
+#define RIO_S_PW_REGS_OFFSET 0x134e0
+#define RIO_ATMU_REGS_DBELL_OFFSET 0x10C40
+
+#define MAX_MSG_UNIT_NUM 2
+#define MAX_PORT_NUM 4
+
struct rio_atmu_regs {
u32 rowtar;
u32 rowtear;
u32 rowbar;
- u32 pad2;
+ u32 pad1;
u32 rowar;
- u32 pad3[3];
+ u32 pad2[3];
+};
+
+struct rio_dbell_ring {
+ void *virt;
+ dma_addr_t phys;
};
struct rio_port_write_msg {
@@ -53,26 +76,60 @@ struct rio_port_write_msg {
u32 discard_count;
};
-struct rio_priv {
+struct fsl_rio_dbell {
+ struct rio_mport *mport[MAX_PORT_NUM];
struct device *dev;
- void __iomem *regs_win;
- struct rio_atmu_regs __iomem *atmu_regs;
- struct rio_atmu_regs __iomem *maint_atmu_regs;
- void __iomem *maint_win;
+ struct rio_dbell_regs __iomem *dbell_regs;
+ struct rio_dbell_ring dbell_ring;
+ int bellirq;
+};
+
+struct fsl_rio_pw {
+ struct device *dev;
+ struct rio_pw_regs __iomem *pw_regs;
struct rio_port_write_msg port_write_msg;
int pwirq;
struct work_struct pw_work;
struct kfifo pw_fifo;
spinlock_t pw_fifo_lock;
+};
+
+struct rio_priv {
+ struct device *dev;
+ void __iomem *regs_win;
+ struct rio_atmu_regs __iomem *atmu_regs;
+ struct rio_atmu_regs __iomem *maint_atmu_regs;
+ void __iomem *maint_win;
void *rmm_handle; /* RapidIO message manager(unit) Handle */
};
extern void __iomem *rio_regs_win;
+extern void __iomem *rmu_regs_win;
+
+extern resource_size_t rio_law_start;
+
+extern struct fsl_rio_dbell *dbell;
+extern struct fsl_rio_pw *pw;
extern int fsl_rio_setup_rmu(struct rio_mport *mport,
struct device_node *node);
-extern int fsl_rio_port_write_init(struct rio_mport *mport);
+extern int fsl_rio_port_write_init(struct fsl_rio_pw *pw);
extern int fsl_rio_pw_enable(struct rio_mport *mport, int enable);
-extern void fsl_rio_port_error_handler(struct rio_mport *port, int offset);
+extern void fsl_rio_port_error_handler(int offset);
+extern int fsl_rio_doorbell_init(struct fsl_rio_dbell *dbell);
+
+extern int fsl_rio_doorbell_send(struct rio_mport *mport,
+ int index, u16 destid, u16 data);
+extern int fsl_add_outb_message(struct rio_mport *mport,
+ struct rio_dev *rdev,
+ int mbox, void *buffer, size_t len);
+extern int fsl_open_outb_mbox(struct rio_mport *mport,
+ void *dev_id, int mbox, int entries);
+extern void fsl_close_outb_mbox(struct rio_mport *mport, int mbox);
+extern int fsl_open_inb_mbox(struct rio_mport *mport,
+ void *dev_id, int mbox, int entries);
+extern void fsl_close_inb_mbox(struct rio_mport *mport, int mbox);
+extern int fsl_add_inb_buffer(struct rio_mport *mport, int mbox, void *buf);
+extern void *fsl_get_inb_message(struct rio_mport *mport, int mbox);
#endif
diff --git a/arch/powerpc/sysdev/fsl_rmu.c b/arch/powerpc/sysdev/fsl_rmu.c
index 0a3e6cf..02445a5 100644
--- a/arch/powerpc/sysdev/fsl_rmu.c
+++ b/arch/powerpc/sysdev/fsl_rmu.c
@@ -36,8 +36,8 @@
(((struct rio_priv *)(mport->priv))->rmm_handle)
/* RapidIO definition irq, which read from OF-tree */
-#define IRQ_RIO_PW(m) (((struct rio_priv *)(m->priv))->pwirq)
-#define IRQ_RIO_BELL(m) (((struct fsl_rmu *)(GET_RMM_HANDLE(m)))->bellirq)
+#define IRQ_RIO_PW(m) (((struct fsl_rio_pw *)(m))->pwirq)
+#define IRQ_RIO_BELL(m) (((struct fsl_rio_dbell *)(m))->bellirq)
#define IRQ_RIO_TX(m) (((struct fsl_rmu *)(GET_RMM_HANDLE(m)))->txirq)
#define IRQ_RIO_RX(m) (((struct fsl_rmu *)(GET_RMM_HANDLE(m)))->rxirq)
@@ -73,13 +73,10 @@
#define LTLEECSR_ENABLE_ALL 0xFFC000FC
#define RIO_LTLEECSR 0x060c
-#define RIO_IM0SR 0x13064
-#define RIO_IM1SR 0x13164
-#define RIO_OM0SR 0x13004
-#define RIO_OM1SR 0x13104
-
-#define RIO_P_MSG_REGS_OFFSET 0x11000
-#define RIO_S_MSG_REGS_OFFSET 0x13000
+#define RIO_IM0SR 0x64
+#define RIO_IM1SR 0x164
+#define RIO_OM0SR 0x4
+#define RIO_OM1SR 0x104
#define RIO_DBELL_WIN_SIZE 0x1000
@@ -113,75 +110,60 @@
#define DBELL_INF(x) (*(u16 *)(x + DOORBELL_INFO_OFFSET))
struct rio_msg_regs {
- u32 omr; /* 0xD_3000 - Outbound message 0 mode register */
- u32 osr; /* 0xD_3004 - Outbound message 0 status register */
+ u32 omr;
+ u32 osr;
u32 pad1;
- u32 odqdpar; /* 0xD_300C - Outbound message 0 descriptor queue
- dequeue pointer address register */
+ u32 odqdpar;
u32 pad2;
- u32 osar; /* 0xD_3014 - Outbound message 0 source address
- register */
- u32 odpr; /* 0xD_3018 - Outbound message 0 destination port
- register */
- u32 odatr; /* 0xD_301C - Outbound message 0 destination attributes
- Register*/
- u32 odcr; /* 0xD_3020 - Outbound message 0 double-word count
- register */
+ u32 osar;
+ u32 odpr;
+ u32 odatr;
+ u32 odcr;
u32 pad3;
- u32 odqepar; /* 0xD_3028 - Outbound message 0 descriptor queue
- enqueue pointer address register */
+ u32 odqepar;
u32 pad4[13];
- u32 imr; /* 0xD_3060 - Inbound message 0 mode register */
- u32 isr; /* 0xD_3064 - Inbound message 0 status register */
+ u32 imr;
+ u32 isr;
u32 pad5;
- u32 ifqdpar; /* 0xD_306C - Inbound message 0 frame queue dequeue
- pointer address register*/
+ u32 ifqdpar;
u32 pad6;
- u32 ifqepar; /* 0xD_3074 - Inbound message 0 frame queue enqueue
- pointer address register */
- u32 pad7[226];
- u32 odmr; /* 0xD_3400 - Outbound doorbell mode register */
- u32 odsr; /* 0xD_3404 - Outbound doorbell status register */
- u32 res0[4];
- u32 oddpr; /* 0xD_3418 - Outbound doorbell destination port
- register */
- u32 oddatr; /* 0xD_341c - Outbound doorbell destination attributes
- register */
- u32 res1[3];
- u32 odretcr; /* 0xD_342C - Outbound doorbell retry error threshold
- configuration register */
- u32 res2[12];
- u32 dmr; /* 0xD_3460 - Inbound doorbell mode register */
- u32 dsr; /* 0xD_3464 - Inbound doorbell status register */
- u32 pad8;
- u32 dqdpar; /* 0xD_346C - Inbound doorbell queue dequeue Pointer
- address register */
- u32 pad9;
- u32 dqepar; /* 0xD_3474 - Inbound doorbell Queue enqueue pointer
- address register */
- u32 pad10[26];
- u32 pwmr; /* 0xD_34E0 - Inbound port-write mode register */
- u32 pwsr; /* 0xD_34E4 - Inbound port-write status register */
- u32 epwqbar; /* 0xD_34E8 - Extended Port-Write Queue Base Address
- register */
- u32 pwqbar; /* 0xD_34EC - Inbound port-write queue base address
- register */
+ u32 ifqepar;
+};
+
+struct rio_dbell_regs {
+ u32 odmr;
+ u32 odsr;
+ u32 pad1[4];
+ u32 oddpr;
+ u32 oddatr;
+ u32 pad2[3];
+ u32 odretcr;
+ u32 pad3[12];
+ u32 dmr;
+ u32 dsr;
+ u32 pad4;
+ u32 dqdpar;
+ u32 pad5;
+ u32 dqepar;
+};
+
+struct rio_pw_regs {
+ u32 pwmr;
+ u32 pwsr;
+ u32 epwqbar;
+ u32 pwqbar;
};
+
struct rio_tx_desc {
- u32 res1;
+ u32 pad1;
u32 saddr;
u32 dport;
u32 dattr;
- u32 res2;
- u32 res3;
+ u32 pad2;
+ u32 pad3;
u32 dwcnt;
- u32 res4;
-};
-
-struct rio_dbell_ring {
- void *virt;
- dma_addr_t phys;
+ u32 pad4;
};
struct rio_msg_tx_ring {
@@ -204,13 +186,9 @@ struct rio_msg_rx_ring {
};
struct fsl_rmu {
- struct rio_atmu_regs __iomem *dbell_atmu_regs;
- void __iomem *dbell_win;
struct rio_msg_regs __iomem *msg_regs;
- struct rio_dbell_ring dbell_ring;
struct rio_msg_tx_ring msg_tx_ring;
struct rio_msg_rx_ring msg_rx_ring;
- int bellirq;
int txirq;
int rxirq;
};
@@ -247,9 +225,11 @@ fsl_rio_tx_handler(int irq, void *dev_instance)
if (osr & RIO_MSG_OSR_EOMI) {
u32 dqp = in_be32(&rmu->msg_regs->odqdpar);
int slot = (dqp - rmu->msg_tx_ring.phys) >> 5;
- port->outb_msg[0].mcback(port, rmu->msg_tx_ring.dev_id, -1,
- slot);
-
+ if (port->outb_msg[0].mcback != NULL) {
+ port->outb_msg[0].mcback(port, rmu->msg_tx_ring.dev_id,
+ -1,
+ slot);
+ }
/* Ack the end-of-message interrupt */
out_be32(&rmu->msg_regs->osr, RIO_MSG_OSR_EOMI);
}
@@ -284,12 +264,14 @@ fsl_rio_rx_handler(int irq, void *dev_instance)
/* XXX Need to check/dispatch until queue empty */
if (isr & RIO_MSG_ISR_DIQI) {
/*
- * We implement *only* mailbox 0, but can receive messages
- * for any mailbox/letter to that mailbox destination. So,
- * make the callback with an unknown/invalid mailbox number
- * argument.
- */
- port->inb_msg[0].mcback(port, rmu->msg_rx_ring.dev_id, -1, -1);
+ * Can receive messages for any mailbox/letter to that
+ * mailbox destination. So, make the callback with an
+ * unknown/invalid mailbox number argument.
+ */
+ if (port->inb_msg[0].mcback != NULL)
+ port->inb_msg[0].mcback(port, rmu->msg_rx_ring.dev_id,
+ -1,
+ -1);
/* Ack the queueing interrupt */
out_be32(&rmu->msg_regs->isr, RIO_MSG_ISR_DIQI);
@@ -311,27 +293,27 @@ static irqreturn_t
fsl_rio_dbell_handler(int irq, void *dev_instance)
{
int dsr;
- struct rio_mport *port = (struct rio_mport *)dev_instance;
- struct fsl_rmu *rmu = GET_RMM_HANDLE(port);
+ struct fsl_rio_dbell *fsl_dbell = (struct fsl_rio_dbell *)dev_instance;
+ int i;
- dsr = in_be32(&rmu->msg_regs->dsr);
+ dsr = in_be32(&fsl_dbell->dbell_regs->dsr);
if (dsr & DOORBELL_DSR_TE) {
pr_info("RIO: doorbell reception error\n");
- out_be32(&rmu->msg_regs->dsr, DOORBELL_DSR_TE);
+ out_be32(&fsl_dbell->dbell_regs->dsr, DOORBELL_DSR_TE);
goto out;
}
if (dsr & DOORBELL_DSR_QFI) {
pr_info("RIO: doorbell queue full\n");
- out_be32(&rmu->msg_regs->dsr, DOORBELL_DSR_QFI);
+ out_be32(&fsl_dbell->dbell_regs->dsr, DOORBELL_DSR_QFI);
}
/* XXX Need to check/dispatch until queue empty */
if (dsr & DOORBELL_DSR_DIQI) {
u32 dmsg =
- (u32) rmu->dbell_ring.virt +
- (in_be32(&rmu->msg_regs->dqdpar) & 0xfff);
+ (u32) fsl_dbell->dbell_ring.virt +
+ (in_be32(&fsl_dbell->dbell_regs->dqdpar) & 0xfff);
struct rio_dbell *dbell;
int found = 0;
@@ -340,48 +322,58 @@ fsl_rio_dbell_handler(int irq, void *dev_instance)
" sid %2.2x tid %2.2x info %4.4x\n",
DBELL_SID(dmsg), DBELL_TID(dmsg), DBELL_INF(dmsg));
- list_for_each_entry(dbell, &port->dbells, node) {
- if ((dbell->res->start <= DBELL_INF(dmsg)) &&
- (dbell->res->end >= DBELL_INF(dmsg))) {
- found = 1;
- break;
+ for (i = 0; i < MAX_PORT_NUM; i++) {
+ if (fsl_dbell->mport[i]) {
+ list_for_each_entry(dbell,
+ &fsl_dbell->mport[i]->dbells, node) {
+ if ((dbell->res->start
+ <= DBELL_INF(dmsg))
+ && (dbell->res->end
+ >= DBELL_INF(dmsg))) {
+ found = 1;
+ break;
+ }
+ }
+ if (found && dbell->dinb) {
+ dbell->dinb(fsl_dbell->mport[i],
+ dbell->dev_id, DBELL_SID(dmsg),
+ DBELL_TID(dmsg),
+ DBELL_INF(dmsg));
+ break;
+ }
}
}
- if (found) {
- dbell->dinb(port, dbell->dev_id,
- DBELL_SID(dmsg),
- DBELL_TID(dmsg), DBELL_INF(dmsg));
- } else {
+
+ if (!found) {
pr_debug
("RIO: spurious doorbell,"
" sid %2.2x tid %2.2x info %4.4x\n",
DBELL_SID(dmsg), DBELL_TID(dmsg),
DBELL_INF(dmsg));
}
- setbits32(&rmu->msg_regs->dmr, DOORBELL_DMR_DI);
- out_be32(&rmu->msg_regs->dsr, DOORBELL_DSR_DIQI);
+ setbits32(&fsl_dbell->dbell_regs->dmr, DOORBELL_DMR_DI);
+ out_be32(&fsl_dbell->dbell_regs->dsr, DOORBELL_DSR_DIQI);
}
out:
return IRQ_HANDLED;
}
-void msg_unit_error_handler(struct rio_mport *port)
+void msg_unit_error_handler(void)
{
- struct fsl_rmu *rmu = GET_RMM_HANDLE(port);
/*XXX: Error recovery is not implemented, we just clear errors */
out_be32((u32 *)(rio_regs_win + RIO_LTLEDCSR), 0);
- out_be32((u32 *)(rio_regs_win + RIO_IM0SR), IMSR_CLEAR);
- out_be32((u32 *)(rio_regs_win + RIO_IM1SR), IMSR_CLEAR);
- out_be32((u32 *)(rio_regs_win + RIO_OM0SR), OMSR_CLEAR);
- out_be32((u32 *)(rio_regs_win + RIO_OM1SR), OMSR_CLEAR);
+ out_be32((u32 *)(rmu_regs_win + RIO_IM0SR), IMSR_CLEAR);
+ out_be32((u32 *)(rmu_regs_win + RIO_IM1SR), IMSR_CLEAR);
+ out_be32((u32 *)(rmu_regs_win + RIO_OM0SR), OMSR_CLEAR);
+ out_be32((u32 *)(rmu_regs_win + RIO_OM1SR), OMSR_CLEAR);
- out_be32(&rmu->msg_regs->odsr, ODSR_CLEAR);
- out_be32(&rmu->msg_regs->dsr, IDSR_CLEAR);
+ out_be32(&dbell->dbell_regs->odsr, ODSR_CLEAR);
+ out_be32(&dbell->dbell_regs->dsr, IDSR_CLEAR);
- out_be32(&rmu->msg_regs->pwsr, IPWSR_CLEAR);
+ out_be32(&pw->pw_regs->pwsr, IPWSR_CLEAR);
}
/**
@@ -396,18 +388,15 @@ static irqreturn_t
fsl_rio_port_write_handler(int irq, void *dev_instance)
{
u32 ipwmr, ipwsr;
- struct rio_mport *port = (struct rio_mport *)dev_instance;
- struct rio_priv *priv = port->priv;
- struct fsl_rmu *rmu;
+ struct fsl_rio_pw *pw = (struct fsl_rio_pw *)dev_instance;
u32 epwisr, tmp;
- rmu = GET_RMM_HANDLE(port);
- epwisr = in_be32(priv->regs_win + RIO_EPWISR);
+ epwisr = in_be32(rio_regs_win + RIO_EPWISR);
if (!(epwisr & RIO_EPWISR_PW))
goto pw_done;
- ipwmr = in_be32(&rmu->msg_regs->pwmr);
- ipwsr = in_be32(&rmu->msg_regs->pwsr);
+ ipwmr = in_be32(&pw->pw_regs->pwmr);
+ ipwsr = in_be32(&pw->pw_regs->pwsr);
#ifdef DEBUG_PW
pr_debug("PW Int->IPWMR: 0x%08x IPWSR: 0x%08x (", ipwmr, ipwsr);
@@ -428,60 +417,60 @@ fsl_rio_port_write_handler(int irq, void *dev_instance)
/* Save PW message (if there is room in FIFO),
* otherwise discard it.
*/
- if (kfifo_avail(&priv->pw_fifo) >= RIO_PW_MSG_SIZE) {
- priv->port_write_msg.msg_count++;
- kfifo_in(&priv->pw_fifo, priv->port_write_msg.virt,
+ if (kfifo_avail(&pw->pw_fifo) >= RIO_PW_MSG_SIZE) {
+ pw->port_write_msg.msg_count++;
+ kfifo_in(&pw->pw_fifo, pw->port_write_msg.virt,
RIO_PW_MSG_SIZE);
} else {
- priv->port_write_msg.discard_count++;
+ pw->port_write_msg.discard_count++;
pr_debug("RIO: ISR Discarded Port-Write Msg(s) (%d)\n",
- priv->port_write_msg.discard_count);
+ pw->port_write_msg.discard_count);
}
/* Clear interrupt and issue Clear Queue command. This allows
* another port-write to be received.
*/
- out_be32(&rmu->msg_regs->pwsr, RIO_IPWSR_QFI);
- out_be32(&rmu->msg_regs->pwmr, ipwmr | RIO_IPWMR_CQ);
+ out_be32(&pw->pw_regs->pwsr, RIO_IPWSR_QFI);
+ out_be32(&pw->pw_regs->pwmr, ipwmr | RIO_IPWMR_CQ);
- schedule_work(&priv->pw_work);
+ schedule_work(&pw->pw_work);
}
if ((ipwmr & RIO_IPWMR_EIE) && (ipwsr & RIO_IPWSR_TE)) {
- priv->port_write_msg.err_count++;
+ pw->port_write_msg.err_count++;
pr_debug("RIO: Port-Write Transaction Err (%d)\n",
- priv->port_write_msg.err_count);
+ pw->port_write_msg.err_count);
/* Clear Transaction Error: port-write controller should be
* disabled when clearing this error
*/
- out_be32(&rmu->msg_regs->pwmr, ipwmr & ~RIO_IPWMR_PWE);
- out_be32(&rmu->msg_regs->pwsr, RIO_IPWSR_TE);
- out_be32(&rmu->msg_regs->pwmr, ipwmr);
+ out_be32(&pw->pw_regs->pwmr, ipwmr & ~RIO_IPWMR_PWE);
+ out_be32(&pw->pw_regs->pwsr, RIO_IPWSR_TE);
+ out_be32(&pw->pw_regs->pwmr, ipwmr);
}
if (ipwsr & RIO_IPWSR_PWD) {
- priv->port_write_msg.discard_count++;
+ pw->port_write_msg.discard_count++;
pr_debug("RIO: Port Discarded Port-Write Msg(s) (%d)\n",
- priv->port_write_msg.discard_count);
- out_be32(&rmu->msg_regs->pwsr, RIO_IPWSR_PWD);
+ pw->port_write_msg.discard_count);
+ out_be32(&pw->pw_regs->pwsr, RIO_IPWSR_PWD);
}
pw_done:
if (epwisr & RIO_EPWISR_PINT1) {
- tmp = in_be32(priv->regs_win + RIO_LTLEDCSR);
+ tmp = in_be32(rio_regs_win + RIO_LTLEDCSR);
pr_debug("RIO_LTLEDCSR = 0x%x\n", tmp);
- fsl_rio_port_error_handler(port, 0);
+ fsl_rio_port_error_handler(0);
}
if (epwisr & RIO_EPWISR_PINT2) {
- tmp = in_be32(priv->regs_win + RIO_LTLEDCSR);
+ tmp = in_be32(rio_regs_win + RIO_LTLEDCSR);
pr_debug("RIO_LTLEDCSR = 0x%x\n", tmp);
- fsl_rio_port_error_handler(port, 1);
+ fsl_rio_port_error_handler(1);
}
if (epwisr & RIO_EPWISR_MU) {
- tmp = in_be32(priv->regs_win + RIO_LTLEDCSR);
+ tmp = in_be32(rio_regs_win + RIO_LTLEDCSR);
pr_debug("RIO_LTLEDCSR = 0x%x\n", tmp);
- msg_unit_error_handler(port);
+ msg_unit_error_handler();
}
return IRQ_HANDLED;
@@ -489,18 +478,15 @@ pw_done:
static void fsl_pw_dpc(struct work_struct *work)
{
- struct rio_priv *priv = container_of(work, struct rio_priv, pw_work);
- unsigned long flags;
+ struct fsl_rio_pw *pw = container_of(work, struct fsl_rio_pw, pw_work);
u32 msg_buffer[RIO_PW_MSG_SIZE/sizeof(u32)];
/*
* Process port-write messages
*/
- spin_lock_irqsave(&priv->pw_fifo_lock, flags);
- while (kfifo_out(&priv->pw_fifo, (unsigned char *)msg_buffer,
- RIO_PW_MSG_SIZE)) {
+ while (kfifo_out_spinlocked(&pw->pw_fifo, (unsigned char *)msg_buffer,
+ RIO_PW_MSG_SIZE, &pw->pw_fifo_lock)) {
/* Process one message */
- spin_unlock_irqrestore(&priv->pw_fifo_lock, flags);
#ifdef DEBUG_PW
{
u32 i;
@@ -517,31 +503,26 @@ static void fsl_pw_dpc(struct work_struct *work)
#endif
/* Pass the port-write message to RIO core for processing */
rio_inb_pwrite_handler((union rio_pw_msg *)msg_buffer);
- spin_lock_irqsave(&priv->pw_fifo_lock, flags);
}
- spin_unlock_irqrestore(&priv->pw_fifo_lock, flags);
}
/**
* fsl_rio_pw_enable - enable/disable port-write interface init
* @mport: Master port implementing the port write unit
- * @enable: 1=enable; 0=disable port-write message handling
+ * @enable: 1=enable; 0=disable port-write message handling
*/
int fsl_rio_pw_enable(struct rio_mport *mport, int enable)
{
- struct fsl_rmu *rmu;
u32 rval;
- rmu = GET_RMM_HANDLE(mport);
-
- rval = in_be32(&rmu->msg_regs->pwmr);
+ rval = in_be32(&pw->pw_regs->pwmr);
if (enable)
rval |= RIO_IPWMR_PWE;
else
rval &= ~RIO_IPWMR_PWE;
- out_be32(&rmu->msg_regs->pwmr, rval);
+ out_be32(&pw->pw_regs->pwmr, rval);
return 0;
}
@@ -555,51 +536,47 @@ int fsl_rio_pw_enable(struct rio_mport *mport, int enable)
* or %-ENOMEM on failure.
*/
-int fsl_rio_port_write_init(struct rio_mport *mport)
+int fsl_rio_port_write_init(struct fsl_rio_pw *pw)
{
- struct rio_priv *priv = mport->priv;
- struct fsl_rmu *rmu;
int rc = 0;
- rmu = GET_RMM_HANDLE(mport);
-
/* Following configurations require a disabled port write controller */
- out_be32(&rmu->msg_regs->pwmr,
- in_be32(&rmu->msg_regs->pwmr) & ~RIO_IPWMR_PWE);
+ out_be32(&pw->pw_regs->pwmr,
+ in_be32(&pw->pw_regs->pwmr) & ~RIO_IPWMR_PWE);
/* Initialize port write */
- priv->port_write_msg.virt = dma_alloc_coherent(priv->dev,
+ pw->port_write_msg.virt = dma_alloc_coherent(pw->dev,
RIO_PW_MSG_SIZE,
- &priv->port_write_msg.phys, GFP_KERNEL);
- if (!priv->port_write_msg.virt) {
+ &pw->port_write_msg.phys, GFP_KERNEL);
+ if (!pw->port_write_msg.virt) {
pr_err("RIO: unable allocate port write queue\n");
return -ENOMEM;
}
- priv->port_write_msg.err_count = 0;
- priv->port_write_msg.discard_count = 0;
+ pw->port_write_msg.err_count = 0;
+ pw->port_write_msg.discard_count = 0;
/* Point dequeue/enqueue pointers at first entry */
- out_be32(&rmu->msg_regs->epwqbar, 0);
- out_be32(&rmu->msg_regs->pwqbar, (u32) priv->port_write_msg.phys);
+ out_be32(&pw->pw_regs->epwqbar, 0);
+ out_be32(&pw->pw_regs->pwqbar, (u32) pw->port_write_msg.phys);
pr_debug("EIPWQBAR: 0x%08x IPWQBAR: 0x%08x\n",
- in_be32(&rmu->msg_regs->epwqbar),
- in_be32(&rmu->msg_regs->pwqbar));
+ in_be32(&pw->pw_regs->epwqbar),
+ in_be32(&pw->pw_regs->pwqbar));
/* Clear interrupt status IPWSR */
- out_be32(&rmu->msg_regs->pwsr,
+ out_be32(&pw->pw_regs->pwsr,
(RIO_IPWSR_TE | RIO_IPWSR_QFI | RIO_IPWSR_PWD));
/* Configure port write contoller for snooping enable all reporting,
clear queue full */
- out_be32(&rmu->msg_regs->pwmr,
+ out_be32(&pw->pw_regs->pwmr,
RIO_IPWMR_SEN | RIO_IPWMR_QFIE | RIO_IPWMR_EIE | RIO_IPWMR_CQ);
/* Hook up port-write handler */
- rc = request_irq(IRQ_RIO_PW(mport), fsl_rio_port_write_handler,
- IRQF_SHARED, "port-write", (void *)mport);
+ rc = request_irq(IRQ_RIO_PW(pw), fsl_rio_port_write_handler,
+ IRQF_SHARED, "port-write", (void *)pw);
if (rc < 0) {
pr_err("MPC85xx RIO: unable to request inbound doorbell irq");
goto err_out;
@@ -607,26 +584,26 @@ int fsl_rio_port_write_init(struct rio_mport *mport)
/* Enable Error Interrupt */
out_be32((u32 *)(rio_regs_win + RIO_LTLEECSR), LTLEECSR_ENABLE_ALL);
- INIT_WORK(&priv->pw_work, fsl_pw_dpc);
- spin_lock_init(&priv->pw_fifo_lock);
- if (kfifo_alloc(&priv->pw_fifo, RIO_PW_MSG_SIZE * 32, GFP_KERNEL)) {
+ INIT_WORK(&pw->pw_work, fsl_pw_dpc);
+ spin_lock_init(&pw->pw_fifo_lock);
+ if (kfifo_alloc(&pw->pw_fifo, RIO_PW_MSG_SIZE * 32, GFP_KERNEL)) {
pr_err("FIFO allocation failed\n");
rc = -ENOMEM;
goto err_out_irq;
}
pr_debug("IPWMR: 0x%08x IPWSR: 0x%08x\n",
- in_be32(&rmu->msg_regs->pwmr),
- in_be32(&rmu->msg_regs->pwsr));
+ in_be32(&pw->pw_regs->pwmr),
+ in_be32(&pw->pw_regs->pwsr));
return rc;
err_out_irq:
- free_irq(IRQ_RIO_PW(mport), (void *)mport);
+ free_irq(IRQ_RIO_PW(pw), (void *)pw);
err_out:
- dma_free_coherent(priv->dev, RIO_PW_MSG_SIZE,
- priv->port_write_msg.virt,
- priv->port_write_msg.phys);
+ dma_free_coherent(pw->dev, RIO_PW_MSG_SIZE,
+ pw->port_write_msg.virt,
+ pw->port_write_msg.phys);
return rc;
}
@@ -640,29 +617,20 @@ err_out:
* Sends a MPC85xx doorbell message. Returns %0 on success or
* %-EINVAL on failure.
*/
-static int fsl_rio_doorbell_send(struct rio_mport *mport,
+int fsl_rio_doorbell_send(struct rio_mport *mport,
int index, u16 destid, u16 data)
{
- struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
-
pr_debug("fsl_doorbell_send: index %d destid %4.4x data %4.4x\n",
index, destid, data);
- switch (mport->phy_type) {
- case RIO_PHY_PARALLEL:
- out_be32(&rmu->dbell_atmu_regs->rowtar, destid << 22);
- out_be16(rmu->dbell_win, data);
- break;
- case RIO_PHY_SERIAL:
- /* In the serial version silicons, such as MPC8548, MPC8641,
- * below operations is must be.
- */
- out_be32(&rmu->msg_regs->odmr, 0x00000000);
- out_be32(&rmu->msg_regs->odretcr, 0x00000004);
- out_be32(&rmu->msg_regs->oddpr, destid << 16);
- out_be32(&rmu->msg_regs->oddatr, data);
- out_be32(&rmu->msg_regs->odmr, 0x00000001);
- break;
- }
+
+ /* In the serial version silicons, such as MPC8548, MPC8641,
+ * below operations is must be.
+ */
+ out_be32(&dbell->dbell_regs->odmr, 0x00000000);
+ out_be32(&dbell->dbell_regs->odretcr, 0x00000004);
+ out_be32(&dbell->dbell_regs->oddpr, destid << 16);
+ out_be32(&dbell->dbell_regs->oddatr, (index << 20) | data);
+ out_be32(&dbell->dbell_regs->odmr, 0x00000001);
return 0;
}
@@ -678,7 +646,7 @@ static int fsl_rio_doorbell_send(struct rio_mport *mport,
* Adds the @buffer message to the MPC85xx outbound message queue. Returns
* %0 on success or %-EINVAL on failure.
*/
-static int
+int
fsl_add_outb_message(struct rio_mport *mport, struct rio_dev *rdev, int mbox,
void *buffer, size_t len)
{
@@ -690,7 +658,6 @@ fsl_add_outb_message(struct rio_mport *mport, struct rio_dev *rdev, int mbox,
pr_debug("RIO: fsl_add_outb_message(): destid %4.4x mbox %d buffer " \
"%8.8x len %8.8x\n", rdev->destid, mbox, (int)buffer, len);
-
if ((len < 8) || (len > RIO_MAX_MSG_SIZE)) {
ret = -EINVAL;
goto out;
@@ -703,22 +670,11 @@ fsl_add_outb_message(struct rio_mport *mport, struct rio_dev *rdev, int mbox,
memset(rmu->msg_tx_ring.virt_buffer[rmu->msg_tx_ring.tx_slot]
+ len, 0, RIO_MAX_MSG_SIZE - len);
- switch (mport->phy_type) {
- case RIO_PHY_PARALLEL:
- /* Set mbox field for message */
- desc->dport = mbox & 0x3;
-
- /* Enable EOMI interrupt, set priority, and set destid */
- desc->dattr = 0x28000000 | (rdev->destid << 2);
- break;
- case RIO_PHY_SERIAL:
- /* Set mbox field for message, and set destid */
- desc->dport = (rdev->destid << 16) | (mbox & 0x3);
-
- /* Enable EOMI interrupt and priority */
- desc->dattr = 0x28000000;
- break;
- }
+ /* Set mbox field for message, and set destid */
+ desc->dport = (rdev->destid << 16) | (mbox & 0x3);
+
+ /* Enable EOMI interrupt and priority */
+ desc->dattr = 0x28000000 | ((mport->index) << 20);
/* Set transfer size aligned to next power of 2 (in double words) */
desc->dwcnt = is_power_of_2(len) ? len : 1 << get_bitmask_order(len);
@@ -750,7 +706,7 @@ out:
* and enables the outbound message unit. Returns %0 on success and
* %-EINVAL or %-ENOMEM on failure.
*/
-static int
+int
fsl_open_outb_mbox(struct rio_mport *mport, void *dev_id, int mbox, int entries)
{
int i, j, rc = 0;
@@ -855,7 +811,7 @@ out_dma:
* Disables the outbound message unit, free all buffers, and
* frees the outbound message interrupt.
*/
-static void fsl_close_outb_mbox(struct rio_mport *mport, int mbox)
+void fsl_close_outb_mbox(struct rio_mport *mport, int mbox)
{
struct rio_priv *priv = mport->priv;
struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
@@ -883,7 +839,7 @@ static void fsl_close_outb_mbox(struct rio_mport *mport, int mbox)
* and enables the inbound message unit. Returns %0 on success
* and %-EINVAL or %-ENOMEM on failure.
*/
-static int
+int
fsl_open_inb_mbox(struct rio_mport *mport, void *dev_id, int mbox, int entries)
{
int i, rc = 0;
@@ -956,7 +912,7 @@ out:
* Disables the inbound message unit, free all buffers, and
* frees the inbound message interrupt.
*/
-static void fsl_close_inb_mbox(struct rio_mport *mport, int mbox)
+void fsl_close_inb_mbox(struct rio_mport *mport, int mbox)
{
struct rio_priv *priv = mport->priv;
struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
@@ -966,7 +922,7 @@ static void fsl_close_inb_mbox(struct rio_mport *mport, int mbox)
/* Free ring */
dma_free_coherent(priv->dev, rmu->msg_rx_ring.size * RIO_MAX_MSG_SIZE,
- rmu->msg_rx_ring.virt, rmu->msg_rx_ring.phys);
+ rmu->msg_rx_ring.virt, rmu->msg_rx_ring.phys);
/* Free interrupt */
free_irq(IRQ_RIO_RX(mport), (void *)mport);
@@ -981,7 +937,7 @@ static void fsl_close_inb_mbox(struct rio_mport *mport, int mbox)
* Adds the @buf buffer to the MPC85xx inbound message queue. Returns
* %0 on success or %-EINVAL on failure.
*/
-static int fsl_add_inb_buffer(struct rio_mport *mport, int mbox, void *buf)
+int fsl_add_inb_buffer(struct rio_mport *mport, int mbox, void *buf)
{
int rc = 0;
struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
@@ -1013,7 +969,7 @@ out:
* Gets the next available inbound message from the inbound message queue.
* A pointer to the message is returned on success or NULL on failure.
*/
-static void *fsl_get_inb_message(struct rio_mport *mport, int mbox)
+void *fsl_get_inb_message(struct rio_mport *mport, int mbox)
{
struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
u32 phys_buf, virt_buf;
@@ -1058,53 +1014,39 @@ out2:
* ring. Called from fsl_rio_setup(). Returns %0 on success
* or %-ENOMEM on failure.
*/
-static int fsl_rio_doorbell_init(struct rio_mport *mport)
+int fsl_rio_doorbell_init(struct fsl_rio_dbell *dbell)
{
- struct rio_priv *priv = mport->priv;
- struct fsl_rmu *rmu = GET_RMM_HANDLE(mport);
int rc = 0;
- /* Map outbound doorbell window immediately after maintenance window */
- rmu->dbell_win = ioremap(mport->iores.start + RIO_MAINT_WIN_SIZE,
- RIO_DBELL_WIN_SIZE);
- if (!rmu->dbell_win) {
- printk(KERN_ERR
- "RIO: unable to map outbound doorbell window\n");
- rc = -ENOMEM;
- goto out;
- }
-
/* Initialize inbound doorbells */
- rmu->dbell_ring.virt = dma_alloc_coherent(priv->dev, 512 *
- DOORBELL_MESSAGE_SIZE, &rmu->dbell_ring.phys, GFP_KERNEL);
- if (!rmu->dbell_ring.virt) {
+ dbell->dbell_ring.virt = dma_alloc_coherent(dbell->dev, 512 *
+ DOORBELL_MESSAGE_SIZE, &dbell->dbell_ring.phys, GFP_KERNEL);
+ if (!dbell->dbell_ring.virt) {
printk(KERN_ERR "RIO: unable allocate inbound doorbell ring\n");
rc = -ENOMEM;
- iounmap(rmu->dbell_win);
goto out;
}
/* Point dequeue/enqueue pointers at first entry in ring */
- out_be32(&rmu->msg_regs->dqdpar, (u32) rmu->dbell_ring.phys);
- out_be32(&rmu->msg_regs->dqepar, (u32) rmu->dbell_ring.phys);
+ out_be32(&dbell->dbell_regs->dqdpar, (u32) dbell->dbell_ring.phys);
+ out_be32(&dbell->dbell_regs->dqepar, (u32) dbell->dbell_ring.phys);
/* Clear interrupt status */
- out_be32(&rmu->msg_regs->dsr, 0x00000091);
+ out_be32(&dbell->dbell_regs->dsr, 0x00000091);
/* Hook up doorbell handler */
- rc = request_irq(IRQ_RIO_BELL(mport), fsl_rio_dbell_handler, 0,
- "dbell_rx", (void *)mport);
+ rc = request_irq(IRQ_RIO_BELL(dbell), fsl_rio_dbell_handler, 0,
+ "dbell_rx", (void *)dbell);
if (rc < 0) {
- iounmap(rmu->dbell_win);
- dma_free_coherent(priv->dev, 512 * DOORBELL_MESSAGE_SIZE,
- rmu->dbell_ring.virt, rmu->dbell_ring.phys);
+ dma_free_coherent(dbell->dev, 512 * DOORBELL_MESSAGE_SIZE,
+ dbell->dbell_ring.virt, dbell->dbell_ring.phys);
printk(KERN_ERR
"MPC85xx RIO: unable to request inbound doorbell irq");
goto out;
}
/* Configure doorbells for snooping, 512 entries, and enable */
- out_be32(&rmu->msg_regs->dmr, 0x00108161);
+ out_be32(&dbell->dbell_regs->dmr, 0x00108161);
out:
return rc;
@@ -1114,50 +1056,48 @@ int fsl_rio_setup_rmu(struct rio_mport *mport, struct device_node *node)
{
struct rio_priv *priv;
struct fsl_rmu *rmu;
- struct rio_ops *ops;
+ u64 msg_start;
+ const u32 *msg_addr;
+ int mlen;
+ int aw;
- if (!mport || !mport->priv || !node)
- return -1;
+ if (!mport || !mport->priv)
+ return -EINVAL;
+
+ priv = mport->priv;
+
+ if (!node) {
+ dev_warn(priv->dev, "Can't get %s property 'fsl,rmu'\n",
+ priv->dev->of_node->full_name);
+ return -EINVAL;
+ }
rmu = kzalloc(sizeof(struct fsl_rmu), GFP_KERNEL);
if (!rmu)
return -ENOMEM;
- priv = mport->priv;
+ aw = of_n_addr_cells(node);
+ msg_addr = of_get_property(node, "reg", &mlen);
+ if (!msg_addr) {
+ pr_err("%s: unable to find 'reg' property of message-unit\n",
+ node->full_name);
+ return -ENOMEM;
+ }
+ msg_start = of_read_number(msg_addr, aw);
+
+ rmu->msg_regs = (struct rio_msg_regs *)
+ (rmu_regs_win + (u32)msg_start);
+
+ rmu->txirq = irq_of_parse_and_map(node, 0);
+ rmu->rxirq = irq_of_parse_and_map(node, 1);
+ printk(KERN_INFO "%s: txirq: %d, rxirq %d\n",
+ node->full_name, rmu->txirq, rmu->rxirq);
+
priv->rmm_handle = rmu;
- rmu->dbell_atmu_regs = priv->atmu_regs + 2;
- rmu->msg_regs = (struct rio_msg_regs *)(priv->regs_win +
- ((mport->phy_type == RIO_PHY_SERIAL) ?
- RIO_S_MSG_REGS_OFFSET : RIO_P_MSG_REGS_OFFSET));
-
- rmu->bellirq = irq_of_parse_and_map(node, 2);
- rmu->txirq = irq_of_parse_and_map(node, 3);
- rmu->rxirq = irq_of_parse_and_map(node, 4);
- dev_info(priv->dev, "bellirq: %d, txirq: %d, rxirq %d\n",
- rmu->bellirq, rmu->txirq, rmu->rxirq);
-
- ops = mport->ops;
-
- ops->dsend = fsl_rio_doorbell_send;
- ops->open_outb_mbox = fsl_open_outb_mbox;
- ops->open_inb_mbox = fsl_open_inb_mbox;
- ops->close_outb_mbox = fsl_close_outb_mbox;
- ops->close_inb_mbox = fsl_close_inb_mbox;
- ops->add_outb_message = fsl_add_outb_message;
- ops->add_inb_buffer = fsl_add_inb_buffer;
- ops->get_inb_message = fsl_get_inb_message;
rio_init_dbell_res(&mport->riores[RIO_DOORBELL_RESOURCE], 0, 0xffff);
rio_init_mbox_res(&mport->riores[RIO_INB_MBOX_RESOURCE], 0, 0);
rio_init_mbox_res(&mport->riores[RIO_OUTB_MBOX_RESOURCE], 0, 0);
- /* Configure outbound doorbell window */
- out_be32(&rmu->dbell_atmu_regs->rowbar,
- (mport->iores.start + RIO_MAINT_WIN_SIZE) >> 12);
- /* 4k window size */
- out_be32(&rmu->dbell_atmu_regs->rowar, 0x8004200b);
-
- fsl_rio_doorbell_init(mport);
-
return 0;
}
--
1.7.3.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* RE: [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message units support
2011-11-12 12:02 ` [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message units support Liu Gang
@ 2011-11-16 13:39 ` Bounine, Alexandre
2011-11-16 15:33 ` Kumar Gala
0 siblings, 1 reply; 18+ messages in thread
From: Bounine, Alexandre @ 2011-11-16 13:39 UTC (permalink / raw)
To: Liu Gang, linuxppc-dev
Cc: Jin Qing, r58472, linux-kernel, r61911, akpm, B11780
> -----Original Message-----
> From: =
linuxppc-dev-bounces+alexandre.bounine=3Didt.com@lists.ozlabs.org
> [mailto:linuxppc-dev-
> bounces+alexandre.bounine=3Didt.com@lists.ozlabs.org] On Behalf Of Liu
> Gang
> Sent: Saturday, November 12, 2011 7:02 AM
> To: linuxppc-dev@lists.ozlabs.org; Bounine, Alexandre
> Cc: Jin Qing; r58472@freescale.com; r61911@freescale.com; linux-
> kernel@vger.kernel.org; Liu Gang; akpm@linux-foundation.org;
> B11780@freescale.com
> Subject: [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message
> units support
>=20
> Usually, freescale rapidio endpoint can support one or two 1x or 4X
> LP-Serial link interfaces, and rapidio message transactions can be
> implemented by two message units. This adds the support of two
> rapidio ports and initializes message unit 0 and message unit 1. And
> these ports and message units can work simultaneously.
>=20
> Signed-off-by: Li Yang <leoli@freescale.com>
> Signed-off-by: Jin Qing <b24347@freescale.com>
> Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> arch/powerpc/sysdev/fsl_rio.c | 391 +++++++++++++++++++++-----------
> arch/powerpc/sysdev/fsl_rio.h | 75 ++++++-
> arch/powerpc/sysdev/fsl_rmu.c | 502
++++++++++++++++++---------------
> --------
> 3 files changed, 545 insertions(+), 423 deletions(-)
>=20
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message units support
2011-11-16 13:39 ` Bounine, Alexandre
@ 2011-11-16 15:33 ` Kumar Gala
0 siblings, 0 replies; 18+ messages in thread
From: Kumar Gala @ 2011-11-16 15:33 UTC (permalink / raw)
To: Bounine, Alexandre
Cc: Jin Qing, r58472, r61911, linux-kernel, Liu Gang, akpm,
linuxppc-dev, B11780
On Nov 16, 2011, at 7:39 AM, Bounine, Alexandre wrote:
>> -----Original Message-----
>> From: linuxppc-dev-bounces+alexandre.bounine=idt.com@lists.ozlabs.org
>> [mailto:linuxppc-dev-
>> bounces+alexandre.bounine=idt.com@lists.ozlabs.org] On Behalf Of Liu
>> Gang
>> Sent: Saturday, November 12, 2011 7:02 AM
>> To: linuxppc-dev@lists.ozlabs.org; Bounine, Alexandre
>> Cc: Jin Qing; r58472@freescale.com; r61911@freescale.com; linux-
>> kernel@vger.kernel.org; Liu Gang; akpm@linux-foundation.org;
>> B11780@freescale.com
>> Subject: [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message
>> units support
>>
>> Usually, freescale rapidio endpoint can support one or two 1x or 4X
>> LP-Serial link interfaces, and rapidio message transactions can be
>> implemented by two message units. This adds the support of two
>> rapidio ports and initializes message unit 0 and message unit 1. And
>> these ports and message units can work simultaneously.
>>
>> Signed-off-by: Li Yang <leoli@freescale.com>
>> Signed-off-by: Jin Qing <b24347@freescale.com>
>> Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
>> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
>> ---
>> arch/powerpc/sysdev/fsl_rio.c | 391 +++++++++++++++++++++-----------
>> arch/powerpc/sysdev/fsl_rio.h | 75 ++++++-
>> arch/powerpc/sysdev/fsl_rmu.c | 502
> ++++++++++++++++++---------------
>> --------
>> 3 files changed, 545 insertions(+), 423 deletions(-)
>>
>
> Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
>
applied to 'next'
- k
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 3/5,v3] powerpc/85xx: Update SRIO device tree nodes
2011-11-12 12:02 [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Liu Gang
2011-11-12 12:02 ` [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message units support Liu Gang
@ 2011-11-12 12:02 ` Liu Gang
2011-11-16 13:40 ` Bounine, Alexandre
2011-11-16 15:35 ` Kumar Gala
2011-11-12 12:02 ` [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding Liu Gang
` (2 subsequent siblings)
4 siblings, 2 replies; 18+ messages in thread
From: Liu Gang @ 2011-11-12 12:02 UTC (permalink / raw)
To: linuxppc-dev, Alexandre.Bounine
Cc: r58472, r61911, linux-kernel, akpm, B11780
From: Kumar Gala <galak@kernel.crashing.org>
Update all dts files that support SRIO controllers to match the new
fsl,srio device tree binding.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/mpc8568mds.dts | 66 ++++++++++++++++++++++-------
arch/powerpc/boot/dts/mpc8569mds.dts | 72 +++++++++++++++++++++++++------
arch/powerpc/boot/dts/mpc8641_hpcn.dts | 69 ++++++++++++++++++++++++-------
arch/powerpc/boot/dts/p2041rdb.dts | 11 +++++
arch/powerpc/boot/dts/p2041si.dtsi | 20 +++++++++
arch/powerpc/boot/dts/p3041ds.dts | 11 +++++
arch/powerpc/boot/dts/p3041si.dtsi | 26 ++++++++---
arch/powerpc/boot/dts/p4080ds.dts | 12 ++++-
arch/powerpc/boot/dts/p4080si.dtsi | 64 +++++++++++++++++++++++-----
arch/powerpc/boot/dts/p5020ds.dts | 11 +++++
arch/powerpc/boot/dts/p5020si.dtsi | 26 ++++++++---
11 files changed, 314 insertions(+), 74 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc8568mds.dts b/arch/powerpc/boot/dts/mpc8568mds.dts
index 647daf8..2ca5387 100644
--- a/arch/powerpc/boot/dts/mpc8568mds.dts
+++ b/arch/powerpc/boot/dts/mpc8568mds.dts
@@ -26,7 +26,6 @@
serial1 = &serial1;
pci0 = &pci0;
pci1 = &pci1;
- rapidio0 = &rio0;
};
cpus {
@@ -331,6 +330,41 @@
};
};
+ rmu: rmu@d3000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,srio-rmu";
+ reg = <0xd3000 0x500>;
+ ranges = <0x0 0xd3000 0x500>;
+
+ message-unit@0 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x0 0x100>;
+ interrupts = <
+ 53 2 /* msg1_tx_irq */
+ 54 2>;/* msg1_rx_irq */
+ };
+ message-unit@100 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x100 0x100>;
+ interrupts = <
+ 55 2 /* msg2_tx_irq */
+ 56 2>;/* msg2_rx_irq */
+ };
+ doorbell-unit@400 {
+ compatible = "fsl,srio-dbell-unit";
+ reg = <0x400 0x80>;
+ interrupts = <
+ 49 2 /* bell_outb_irq */
+ 50 2>;/* bell_inb_irq */
+ };
+ port-write-unit@4e0 {
+ compatible = "fsl,srio-port-write-unit";
+ reg = <0x4e0 0x20>;
+ interrupts = <48 2>;
+ };
+ };
+
global-utilities@e0000 {
#address-cells = <1>;
#size-cells = <1>;
@@ -638,22 +672,22 @@
};
};
- rio0: rapidio@e00c00000 {
- #address-cells = <2>;
- #size-cells = <2>;
- compatible = "fsl,mpc8568-rapidio", "fsl,rapidio-delta";
- reg = <0xe00c0000 0x20000>;
- ranges = <0x0 0x0 0xc0000000 0x0 0x20000000>;
- interrupts = <48 2 /* error */
- 49 2 /* bell_outb */
- 50 2 /* bell_inb */
- 53 2 /* msg1_tx */
- 54 2 /* msg1_rx */
- 55 2 /* msg2_tx */
- 56 2 /* msg2_rx */>;
+ rapidio@e00c0000 {
+ reg = <0xe00c0000 0x11000>;
+ compatible = "fsl,srio";
interrupt-parent = <&mpic>;
- sleep = <&pmc 0x00080000 /* controller */
- &pmc 0x00040000>; /* message unit */
+ interrupts = <48 2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ fsl,srio-rmu-handle = <&rmu>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ ranges = <0x0 0x0 0xc0000000 0x0 0x20000000>;
+ };
};
leds {
diff --git a/arch/powerpc/boot/dts/mpc8569mds.dts b/arch/powerpc/boot/dts/mpc8569mds.dts
index 8b72eaf..0d9d167 100644
--- a/arch/powerpc/boot/dts/mpc8569mds.dts
+++ b/arch/powerpc/boot/dts/mpc8569mds.dts
@@ -27,7 +27,6 @@
ethernet5 = &enet5;
ethernet7 = &enet7;
pci1 = &pci1;
- rapidio0 = &rio0;
};
cpus {
@@ -326,6 +325,41 @@
interrupt-parent = <&mpic>;
};
+ rmu: rmu@d3000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,srio-rmu";
+ reg = <0xd3000 0x500>;
+ ranges = <0x0 0xd3000 0x500>;
+
+ message-unit@0 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x0 0x100>;
+ interrupts = <
+ 53 2 /* msg1_tx_irq */
+ 54 2>;/* msg1_rx_irq */
+ };
+ message-unit@100 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x100 0x100>;
+ interrupts = <
+ 55 2 /* msg2_tx_irq */
+ 56 2>;/* msg2_rx_irq */
+ };
+ doorbell-unit@400 {
+ compatible = "fsl,srio-dbell-unit";
+ reg = <0x400 0x80>;
+ interrupts = <
+ 49 2 /* bell_outb_irq */
+ 50 2>;/* bell_inb_irq */
+ };
+ port-write-unit@4e0 {
+ compatible = "fsl,srio-port-write-unit";
+ reg = <0x4e0 0x20>;
+ interrupts = <48 2>;
+ };
+ };
+
global-utilities@e0000 {
#address-cells = <1>;
#size-cells = <1>;
@@ -771,20 +805,30 @@
};
};
- rio0: rapidio@e00c00000 {
- #address-cells = <2>;
- #size-cells = <2>;
- compatible = "fsl,mpc8569-rapidio", "fsl,rapidio-delta";
- reg = <0xe00c0000 0x20000>;
- ranges = <0x0 0x0 0xc0000000 0x0 0x20000000>;
- interrupts = <48 2 /* error */
- 49 2 /* bell_outb */
- 50 2 /* bell_inb */
- 53 2 /* msg1_tx */
- 54 2 /* msg1_rx */
- 55 2 /* msg2_tx */
- 56 2 /* msg2_rx */>;
+ rapidio@e00c0000 {
+ reg = <0xe00c0000 0x11000>;
+ compatible = "fsl,srio";
interrupt-parent = <&mpic>;
+ interrupts = <48 2>;
sleep = <&pmc 0x00080000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ fsl,srio-rmu-handle = <&rmu>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ ranges = <0x0 0x0 0xc0000000 0x0 0x20000000>;
+ };
+
+ port2 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <2>;
+ status = "disabled";
+ };
};
+
};
diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
index 848320e..fb8640e 100644
--- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
+++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
@@ -26,13 +26,6 @@
serial1 = &serial1;
pci0 = &pci0;
pci1 = &pci1;
-/*
- * Only one of Rapid IO or PCI can be present due to HW limitations and
- * due to the fact that the 2 now share address space in the new memory
- * map. The most likely case is that we have PCI, so comment out the
- * rapidio node. Leave it here for reference.
- */
- /* rapidio0 = &rapidio0; */
};
cpus {
@@ -361,6 +354,41 @@
device_type = "open-pic";
};
+ rmu: rmu@d3000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,srio-rmu";
+ reg = <0xd3000 0x500>;
+ ranges = <0x0 0xd3000 0x500>;
+
+ message-unit@0 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x0 0x100>;
+ interrupts = <
+ 53 2 /* msg1_tx_irq */
+ 54 2>;/* msg1_rx_irq */
+ };
+ message-unit@100 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x100 0x100>;
+ interrupts = <
+ 55 2 /* msg2_tx_irq */
+ 56 2>;/* msg2_rx_irq */
+ };
+ doorbell-unit@400 {
+ compatible = "fsl,srio-dbell-unit";
+ reg = <0x400 0x80>;
+ interrupts = <
+ 49 2 /* bell_outb_irq */
+ 50 2>;/* bell_inb_irq */
+ };
+ port-write-unit@4e0 {
+ compatible = "fsl,srio-port-write-unit";
+ reg = <0x4e0 0x20>;
+ interrupts = <48 2>;
+ };
+ };
+
global-utilities@e0000 {
compatible = "fsl,mpc8641-guts";
reg = <0xe0000 0x1000>;
@@ -612,16 +640,27 @@
};
};
/*
- rapidio0: rapidio@ffec0000 {
+ * Only one of Rapid IO or PCI can be present due to HW limitations and
+ * due to the fact that the 2 now share address space in the new memory
+ * map. The most likely case is that we have PCI, so comment out the
+ * rapidio node. Leave it here for reference.
+
+ rapidio@ffec0000 {
+ reg = <0xffec0000 0x11000>;
+ compatible = "fsl,srio";
+ interrupt-parent = <&mpic>;
+ interrupts = <48 2>;
#address-cells = <2>;
#size-cells = <2>;
- compatible = "fsl,rapidio-delta";
- reg = <0xffec0000 0x20000>;
- ranges = <0 0 0x80000000 0 0x20000000>;
- interrupt-parent = <&mpic>;
- // err_irq bell_outb_irq bell_inb_irq
- // msg1_tx_irq msg1_rx_irq msg2_tx_irq msg2_rx_irq
- interrupts = <48 2 49 2 50 2 53 2 54 2 55 2 56 2>;
+ fsl,srio-rmu-handle = <&rmu>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ ranges = <0 0 0x80000000 0 0x20000000>;
+ };
};
*/
diff --git a/arch/powerpc/boot/dts/p2041rdb.dts b/arch/powerpc/boot/dts/p2041rdb.dts
index 79b6895..739d8a7 100644
--- a/arch/powerpc/boot/dts/p2041rdb.dts
+++ b/arch/powerpc/boot/dts/p2041rdb.dts
@@ -106,6 +106,17 @@
};
};
+ rapidio@ffe0c0000 {
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+
+ port1 {
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+ port2 {
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
+ };
+
localbus@ffe124000 {
reg = <0xf 0xfe124000 0 0x1000>;
ranges = <0 0 0xf 0xe8000000 0x08000000>;
diff --git a/arch/powerpc/boot/dts/p2041si.dtsi b/arch/powerpc/boot/dts/p2041si.dtsi
index f7492ed..c2a4314 100644
--- a/arch/powerpc/boot/dts/p2041si.dtsi
+++ b/arch/powerpc/boot/dts/p2041si.dtsi
@@ -602,6 +602,26 @@
};
+ rapidio@ffe0c0000 {
+ compatible = "fsl,srio";
+ interrupts = <16 2 1 11>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ };
+
+ port2 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <2>;
+ };
+ };
+
localbus@ffe124000 {
compatible = "fsl,p2041-elbc", "fsl,elbc", "simple-bus";
interrupts = <25 2 0 0>;
diff --git a/arch/powerpc/boot/dts/p3041ds.dts b/arch/powerpc/boot/dts/p3041ds.dts
index bbd113b..40193e4 100644
--- a/arch/powerpc/boot/dts/p3041ds.dts
+++ b/arch/powerpc/boot/dts/p3041ds.dts
@@ -99,6 +99,17 @@
};
};
+ rapidio@ffe0c0000 {
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+
+ port1 {
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+ port2 {
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
+ };
+
localbus@ffe124000 {
reg = <0xf 0xfe124000 0 0x1000>;
ranges = <0 0 0xf 0xe8000000 0x08000000
diff --git a/arch/powerpc/boot/dts/p3041si.dtsi b/arch/powerpc/boot/dts/p3041si.dtsi
index 87130b7..3ef3ae6 100644
--- a/arch/powerpc/boot/dts/p3041si.dtsi
+++ b/arch/powerpc/boot/dts/p3041si.dtsi
@@ -71,10 +71,6 @@
rtic_c = &rtic_c;
rtic_d = &rtic_d;
sec_mon = &sec_mon;
-
-/*
- rio0 = &rapidio0;
- */
};
cpus {
@@ -607,9 +603,25 @@
};
};
-/*
- rapidio0: rapidio@ffe0c0000
-*/
+ rapidio@ffe0c0000 {
+ compatible = "fsl,srio";
+ interrupts = <16 2 1 11>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ };
+
+ port2 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <2>;
+ };
+ };
localbus@ffe124000 {
compatible = "fsl,p3041-elbc", "fsl,elbc", "simple-bus";
diff --git a/arch/powerpc/boot/dts/p4080ds.dts b/arch/powerpc/boot/dts/p4080ds.dts
index c7916dc..7df35d8 100644
--- a/arch/powerpc/boot/dts/p4080ds.dts
+++ b/arch/powerpc/boot/dts/p4080ds.dts
@@ -105,9 +105,15 @@
};
};
- rapidio0: rapidio@ffe0c0000 {
- reg = <0xf 0xfe0c0000 0 0x20000>;
- ranges = <0 0 0xc 0x20000000 0 0x01000000>;
+ rapidio@ffe0c0000 {
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+
+ port1 {
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+ port2 {
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
};
localbus@ffe124000 {
diff --git a/arch/powerpc/boot/dts/p4080si.dtsi b/arch/powerpc/boot/dts/p4080si.dtsi
index f20c01a..6c7eb35 100644
--- a/arch/powerpc/boot/dts/p4080si.dtsi
+++ b/arch/powerpc/boot/dts/p4080si.dtsi
@@ -70,8 +70,6 @@
rtic_c = &rtic_c;
rtic_d = &rtic_d;
sec_mon = &sec_mon;
-
- rio0 = &rapidio0;
};
cpus {
@@ -347,6 +345,41 @@
0xf7 0 0 0>;
};
+ rmu: rmu@d3000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,srio-rmu";
+ reg = <0xd3000 0x500>;
+ ranges = <0x0 0xd3000 0x500>;
+
+ message-unit@0 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x0 0x100>;
+ interrupts = <
+ 60 2 0 0 /* msg1_tx_irq */
+ 61 2 0 0>;/* msg1_rx_irq */
+ };
+ message-unit@100 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x100 0x100>;
+ interrupts = <
+ 62 2 0 0 /* msg2_tx_irq */
+ 63 2 0 0>;/* msg2_rx_irq */
+ };
+ doorbell-unit@400 {
+ compatible = "fsl,srio-dbell-unit";
+ reg = <0x400 0x80>;
+ interrupts = <
+ 56 2 0 0 /* bell_outb_irq */
+ 57 2 0 0>;/* bell_inb_irq */
+ };
+ port-write-unit@4e0 {
+ compatible = "fsl,srio-port-write-unit";
+ reg = <0x4e0 0x20>;
+ interrupts = <16 2 1 11>;
+ };
+ };
+
guts: global-utilities@e0000 {
compatible = "fsl,qoriq-device-config-1.0";
reg = <0xe0000 0xe00>;
@@ -651,18 +684,25 @@
};
};
- rapidio0: rapidio@ffe0c0000 {
+ rapidio@ffe0c0000 {
+ compatible = "fsl,srio";
+ interrupts = <16 2 1 11>;
#address-cells = <2>;
#size-cells = <2>;
- compatible = "fsl,rapidio-delta";
- interrupts = <
- 16 2 1 11 /* err_irq */
- 56 2 0 0 /* bell_outb_irq */
- 57 2 0 0 /* bell_inb_irq */
- 60 2 0 0 /* msg1_tx_irq */
- 61 2 0 0 /* msg1_rx_irq */
- 62 2 0 0 /* msg2_tx_irq */
- 63 2 0 0>; /* msg2_rx_irq */
+ fsl,srio-rmu-handle = <&rmu>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ };
+
+ port2 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <2>;
+ };
};
localbus@ffe124000 {
diff --git a/arch/powerpc/boot/dts/p5020ds.dts b/arch/powerpc/boot/dts/p5020ds.dts
index e6d4099..e3fb415 100644
--- a/arch/powerpc/boot/dts/p5020ds.dts
+++ b/arch/powerpc/boot/dts/p5020ds.dts
@@ -99,6 +99,17 @@
};
};
+ rapidio@ffe0c0000 {
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+
+ port1 {
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+ port2 {
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
+ };
+
localbus@ffe124000 {
reg = <0xf 0xfe124000 0 0x1000>;
ranges = <0 0 0xf 0xe8000000 0x08000000
diff --git a/arch/powerpc/boot/dts/p5020si.dtsi b/arch/powerpc/boot/dts/p5020si.dtsi
index e7948ad..02d15e3 100644
--- a/arch/powerpc/boot/dts/p5020si.dtsi
+++ b/arch/powerpc/boot/dts/p5020si.dtsi
@@ -71,10 +71,6 @@
rtic_c = &rtic_c;
rtic_d = &rtic_d;
sec_mon = &sec_mon;
-
-/*
- rio0 = &rapidio0;
- */
};
cpus {
@@ -594,9 +590,25 @@
};
};
-/*
- rapidio0: rapidio@ffe0c0000
-*/
+ rapidio@ffe0c0000 {
+ compatible = "fsl,srio";
+ interrupts = <16 2 1 11>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ port1 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <1>;
+ };
+
+ port2 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ cell-index = <2>;
+ };
+ };
localbus@ffe124000 {
compatible = "fsl,p5020-elbc", "fsl,elbc", "simple-bus";
--
1.7.3.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* RE: [PATCH 3/5,v3] powerpc/85xx: Update SRIO device tree nodes
2011-11-12 12:02 ` [PATCH 3/5,v3] powerpc/85xx: Update SRIO device tree nodes Liu Gang
@ 2011-11-16 13:40 ` Bounine, Alexandre
2011-11-16 15:35 ` Kumar Gala
1 sibling, 0 replies; 18+ messages in thread
From: Bounine, Alexandre @ 2011-11-16 13:40 UTC (permalink / raw)
To: Liu Gang, linuxppc-dev; +Cc: r58472, r61911, linux-kernel, akpm, B11780
> -----Original Message-----
> From: Liu Gang [mailto:Gang.Liu@freescale.com]
> Sent: Saturday, November 12, 2011 7:03 AM
> To: linuxppc-dev@lists.ozlabs.org; Bounine, Alexandre
> Cc: akpm@linux-foundation.org; linux-kernel@vger.kernel.org;
> r58472@freescale.com; B11780@freescale.com; r61911@freescale.com;
Kumar
> Gala
> Subject: [PATCH 3/5,v3] powerpc/85xx: Update SRIO device tree nodes
>=20
> From: Kumar Gala <galak@kernel.crashing.org>
>=20
> Update all dts files that support SRIO controllers to match the new
> fsl,srio device tree binding.
>=20
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> arch/powerpc/boot/dts/mpc8568mds.dts | 66
++++++++++++++++++++++--
> -----
> arch/powerpc/boot/dts/mpc8569mds.dts | 72
> +++++++++++++++++++++++++------
> arch/powerpc/boot/dts/mpc8641_hpcn.dts | 69
> ++++++++++++++++++++++++-------
> arch/powerpc/boot/dts/p2041rdb.dts | 11 +++++
> arch/powerpc/boot/dts/p2041si.dtsi | 20 +++++++++
> arch/powerpc/boot/dts/p3041ds.dts | 11 +++++
> arch/powerpc/boot/dts/p3041si.dtsi | 26 ++++++++---
> arch/powerpc/boot/dts/p4080ds.dts | 12 ++++-
> arch/powerpc/boot/dts/p4080si.dtsi | 64
+++++++++++++++++++++++-
> ----
> arch/powerpc/boot/dts/p5020ds.dts | 11 +++++
> arch/powerpc/boot/dts/p5020si.dtsi | 26 ++++++++---
> 11 files changed, 314 insertions(+), 74 deletions(-)
>=20
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3/5,v3] powerpc/85xx: Update SRIO device tree nodes
2011-11-12 12:02 ` [PATCH 3/5,v3] powerpc/85xx: Update SRIO device tree nodes Liu Gang
2011-11-16 13:40 ` Bounine, Alexandre
@ 2011-11-16 15:35 ` Kumar Gala
1 sibling, 0 replies; 18+ messages in thread
From: Kumar Gala @ 2011-11-16 15:35 UTC (permalink / raw)
To: Liu Gang
Cc: r58472, linux-kernel, r61911, Alexandre.Bounine, akpm,
linuxppc-dev, B11780
On Nov 12, 2011, at 6:02 AM, Liu Gang wrote:
> From: Kumar Gala <galak@kernel.crashing.org>
>=20
> Update all dts files that support SRIO controllers to match the new
> fsl,srio device tree binding.
>=20
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> arch/powerpc/boot/dts/mpc8568mds.dts | 66 =
++++++++++++++++++++++-------
> arch/powerpc/boot/dts/mpc8569mds.dts | 72 =
+++++++++++++++++++++++++------
> arch/powerpc/boot/dts/mpc8641_hpcn.dts | 69 =
++++++++++++++++++++++++-------
> arch/powerpc/boot/dts/p2041rdb.dts | 11 +++++
> arch/powerpc/boot/dts/p2041si.dtsi | 20 +++++++++
> arch/powerpc/boot/dts/p3041ds.dts | 11 +++++
> arch/powerpc/boot/dts/p3041si.dtsi | 26 ++++++++---
> arch/powerpc/boot/dts/p4080ds.dts | 12 ++++-
> arch/powerpc/boot/dts/p4080si.dtsi | 64 =
+++++++++++++++++++++++-----
> arch/powerpc/boot/dts/p5020ds.dts | 11 +++++
> arch/powerpc/boot/dts/p5020si.dtsi | 26 ++++++++---
> 11 files changed, 314 insertions(+), 74 deletions(-)
I'm holding off on this, since I'm reworking the .dts. I'll workup a =
new patch based on top of the dts changes.
- k=
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding
2011-11-12 12:02 [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Liu Gang
2011-11-12 12:02 ` [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message units support Liu Gang
2011-11-12 12:02 ` [PATCH 3/5,v3] powerpc/85xx: Update SRIO device tree nodes Liu Gang
@ 2011-11-12 12:02 ` Liu Gang
2011-11-14 17:35 ` Scott Wood
2011-11-16 13:48 ` Bounine, Alexandre
2011-11-12 12:02 ` [PATCH 5/5, v3] powerpc/fsl: Document rapidio node binding-information Liu Gang
2011-11-16 13:36 ` [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Bounine, Alexandre
4 siblings, 2 replies; 18+ messages in thread
From: Liu Gang @ 2011-11-12 12:02 UTC (permalink / raw)
To: linuxppc-dev, Alexandre.Bounine
Cc: r58472, Kai Jiang, r61911, linux-kernel, akpm, B11780
From: Kai Jiang <Kai.Jiang@freescale.com>
Update of_platform_bus_probe() RapidIO node to be compitable with
new RapidIO dts compatible property.
Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/platforms/85xx/corenet_ds.c | 2 +-
arch/powerpc/platforms/85xx/mpc85xx_mds.c | 2 +-
arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 2 +-
3 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/powerpc/platforms/85xx/corenet_ds.c b/arch/powerpc/platforms/85xx/corenet_ds.c
index 802ad11..c48b661 100644
--- a/arch/powerpc/platforms/85xx/corenet_ds.c
+++ b/arch/powerpc/platforms/85xx/corenet_ds.c
@@ -112,7 +112,7 @@ static const struct of_device_id of_device_ids[] __devinitconst = {
.compatible = "simple-bus"
},
{
- .compatible = "fsl,rapidio-delta",
+ .compatible = "fsl,srio",
},
{
.compatible = "fsl,p4080-pcie",
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index a23a3ff..7968ced 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -433,7 +433,7 @@ static struct of_device_id mpc85xx_ids[] = {
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
{ .compatible = "gianfar", },
- { .compatible = "fsl,rapidio-delta", },
+ { .compatible = "fsl,srio", },
{ .compatible = "fsl,mpc8548-guts", },
{ .compatible = "gpio-leds", },
{},
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index b11c353..569262c 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -161,7 +161,7 @@ mpc86xx_time_init(void)
static __initdata struct of_device_id of_bus_ids[] = {
{ .compatible = "simple-bus", },
- { .compatible = "fsl,rapidio-delta", },
+ { .compatible = "fsl,srio", },
{ .compatible = "gianfar", },
{},
};
--
1.7.3.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* Re: [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding
2011-11-12 12:02 ` [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding Liu Gang
@ 2011-11-14 17:35 ` Scott Wood
2011-11-14 17:37 ` Scott Wood
2011-11-16 13:48 ` Bounine, Alexandre
1 sibling, 1 reply; 18+ messages in thread
From: Scott Wood @ 2011-11-14 17:35 UTC (permalink / raw)
To: Liu Gang
Cc: r58472, Kai Jiang, linux-kernel, r61911, Alexandre.Bounine, akpm,
linuxppc-dev, B11780
On 11/12/2011 06:02 AM, Liu Gang wrote:
> From: Kai Jiang <Kai.Jiang@freescale.com>
>
> Update of_platform_bus_probe() RapidIO node to be compitable with
> new RapidIO dts compatible property.
>
> Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> arch/powerpc/platforms/85xx/corenet_ds.c | 2 +-
> arch/powerpc/platforms/85xx/mpc85xx_mds.c | 2 +-
> arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 2 +-
> 3 files changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/arch/powerpc/platforms/85xx/corenet_ds.c b/arch/powerpc/platforms/85xx/corenet_ds.c
> index 802ad11..c48b661 100644
> --- a/arch/powerpc/platforms/85xx/corenet_ds.c
> +++ b/arch/powerpc/platforms/85xx/corenet_ds.c
> @@ -112,7 +112,7 @@ static const struct of_device_id of_device_ids[] __devinitconst = {
> .compatible = "simple-bus"
> },
> {
> - .compatible = "fsl,rapidio-delta",
> + .compatible = "fsl,srio",
fsl,srio is too vague. We need to identify the specific hardware (or at
least a concrete programming interface document), not just the bus that
the hardware implements.
-Scott
^ permalink raw reply [flat|nested] 18+ messages in thread* Re: [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding
2011-11-14 17:35 ` Scott Wood
@ 2011-11-14 17:37 ` Scott Wood
2011-11-15 3:21 ` Liu Gang-B34182
0 siblings, 1 reply; 18+ messages in thread
From: Scott Wood @ 2011-11-14 17:37 UTC (permalink / raw)
To: Liu Gang
Cc: r58472, Kai Jiang, r61911, linux-kernel, Alexandre.Bounine, akpm,
linuxppc-dev, B11780
On 11/14/2011 11:35 AM, Scott Wood wrote:
> On 11/12/2011 06:02 AM, Liu Gang wrote:
>> From: Kai Jiang <Kai.Jiang@freescale.com>
>>
>> Update of_platform_bus_probe() RapidIO node to be compitable with
>> new RapidIO dts compatible property.
>>
>> Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
>> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
>> ---
>> arch/powerpc/platforms/85xx/corenet_ds.c | 2 +-
>> arch/powerpc/platforms/85xx/mpc85xx_mds.c | 2 +-
>> arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 2 +-
>> 3 files changed, 3 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/powerpc/platforms/85xx/corenet_ds.c b/arch/powerpc/platforms/85xx/corenet_ds.c
>> index 802ad11..c48b661 100644
>> --- a/arch/powerpc/platforms/85xx/corenet_ds.c
>> +++ b/arch/powerpc/platforms/85xx/corenet_ds.c
>> @@ -112,7 +112,7 @@ static const struct of_device_id of_device_ids[] __devinitconst = {
>> .compatible = "simple-bus"
>> },
>> {
>> - .compatible = "fsl,rapidio-delta",
>> + .compatible = "fsl,srio",
>
> fsl,srio is too vague. We need to identify the specific hardware (or at
> least a concrete programming interface document), not just the bus that
> the hardware implements.
Never mind, I see that the binding is more specific about what this
string means.
Next time have the binding come first. :-)
-Scott
^ permalink raw reply [flat|nested] 18+ messages in thread* RE: [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding
2011-11-14 17:37 ` Scott Wood
@ 2011-11-15 3:21 ` Liu Gang-B34182
0 siblings, 0 replies; 18+ messages in thread
From: Liu Gang-B34182 @ 2011-11-15 3:21 UTC (permalink / raw)
To: Wood Scott-B07421
Cc: Li Yang-R58472, 'linux-kernel@vger.kernel.org',
Zang Roy-R61911, 'Alexandre.Bounine@idt.com',
Jiang Kai-B18973, 'akpm@linux-foundation.org',
'linuxppc-dev@lists.ozlabs.org', Gala Kumar-B11780
Yeah, send binding first should be better for reviewing entire set of patch=
es.
Thanks!
-----Original Message-----
From: Wood Scott-B07421=20
Sent: Tuesday, November 15, 2011 1:37 AM
To: Liu Gang-B34182
Cc: Li Yang-R58472; Jiang Kai-B18973; linux-kernel@vger.kernel.org; Zang Ro=
y-R61911; Alexandre.Bounine@idt.com; akpm@linux-foundation.org; linuxppc-de=
v@lists.ozlabs.org; Gala Kumar-B11780
Subject: Re: [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for=
new RapidIO node binding
On 11/14/2011 11:35 AM, Scott Wood wrote:
> On 11/12/2011 06:02 AM, Liu Gang wrote:
>> From: Kai Jiang <Kai.Jiang@freescale.com>
>>
>> Update of_platform_bus_probe() RapidIO node to be compitable with new=20
>> RapidIO dts compatible property.
>>
>> Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
>> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
>> ---
>> arch/powerpc/platforms/85xx/corenet_ds.c | 2 +-
>> arch/powerpc/platforms/85xx/mpc85xx_mds.c | 2 +-
>> arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 2 +-
>> 3 files changed, 3 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/powerpc/platforms/85xx/corenet_ds.c=20
>> b/arch/powerpc/platforms/85xx/corenet_ds.c
>> index 802ad11..c48b661 100644
>> --- a/arch/powerpc/platforms/85xx/corenet_ds.c
>> +++ b/arch/powerpc/platforms/85xx/corenet_ds.c
>> @@ -112,7 +112,7 @@ static const struct of_device_id of_device_ids[] __d=
evinitconst =3D {
>> .compatible =3D "simple-bus"
>> },
>> {
>> - .compatible =3D "fsl,rapidio-delta",
>> + .compatible =3D "fsl,srio",
>=20
> fsl,srio is too vague. We need to identify the specific hardware (or=20
> at least a concrete programming interface document), not just the bus =20
> that the hardware implements.
Never mind, I see that the binding is more specific about what this string =
means.
Next time have the binding come first. :-)
-Scott
^ permalink raw reply [flat|nested] 18+ messages in thread
* RE: [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding
2011-11-12 12:02 ` [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding Liu Gang
2011-11-14 17:35 ` Scott Wood
@ 2011-11-16 13:48 ` Bounine, Alexandre
2011-11-16 15:33 ` Kumar Gala
1 sibling, 1 reply; 18+ messages in thread
From: Bounine, Alexandre @ 2011-11-16 13:48 UTC (permalink / raw)
To: Liu Gang, linuxppc-dev
Cc: r58472, Kai Jiang, r61911, linux-kernel, akpm, B11780
> -----Original Message-----
> From: Liu Gang [mailto:Gang.Liu@freescale.com]
> Sent: Saturday, November 12, 2011 7:03 AM
> To: linuxppc-dev@lists.ozlabs.org; Bounine, Alexandre
> Cc: akpm@linux-foundation.org; linux-kernel@vger.kernel.org;
> r58472@freescale.com; B11780@freescale.com; r61911@freescale.com; Kai
> Jiang; Kumar Gala
> Subject: [PATCH 4/5,v3] powerpc/8xxx: Update device tree bus probe for
> new RapidIO node binding
>=20
> From: Kai Jiang <Kai.Jiang@freescale.com>
>=20
> Update of_platform_bus_probe() RapidIO node to be compitable with
> new RapidIO dts compatible property.
>=20
> Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> arch/powerpc/platforms/85xx/corenet_ds.c | 2 +-
> arch/powerpc/platforms/85xx/mpc85xx_mds.c | 2 +-
> arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 2 +-
> 3 files changed, 3 insertions(+), 3 deletions(-)
>=20
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding
2011-11-16 13:48 ` Bounine, Alexandre
@ 2011-11-16 15:33 ` Kumar Gala
0 siblings, 0 replies; 18+ messages in thread
From: Kumar Gala @ 2011-11-16 15:33 UTC (permalink / raw)
To: Bounine, Alexandre
Cc: r58472, Kai Jiang, linux-kernel, r61911, Liu Gang, B11780,
linuxppc-dev, akpm
On Nov 16, 2011, at 7:48 AM, Bounine, Alexandre wrote:
>> -----Original Message-----
>> From: Liu Gang [mailto:Gang.Liu@freescale.com]
>> Sent: Saturday, November 12, 2011 7:03 AM
>> To: linuxppc-dev@lists.ozlabs.org; Bounine, Alexandre
>> Cc: akpm@linux-foundation.org; linux-kernel@vger.kernel.org;
>> r58472@freescale.com; B11780@freescale.com; r61911@freescale.com; Kai
>> Jiang; Kumar Gala
>> Subject: [PATCH 4/5,v3] powerpc/8xxx: Update device tree bus probe for
>> new RapidIO node binding
>>
>> From: Kai Jiang <Kai.Jiang@freescale.com>
>>
>> Update of_platform_bus_probe() RapidIO node to be compitable with
>> new RapidIO dts compatible property.
>>
>> Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
>> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
>> ---
>> arch/powerpc/platforms/85xx/corenet_ds.c | 2 +-
>> arch/powerpc/platforms/85xx/mpc85xx_mds.c | 2 +-
>> arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 2 +-
>> 3 files changed, 3 insertions(+), 3 deletions(-)
>>
>
> Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
applied to 'next'
- k
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 5/5, v3] powerpc/fsl: Document rapidio node binding-information
2011-11-12 12:02 [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Liu Gang
` (2 preceding siblings ...)
2011-11-12 12:02 ` [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding Liu Gang
@ 2011-11-12 12:02 ` Liu Gang
2011-11-16 13:49 ` Bounine, Alexandre
2011-11-16 13:36 ` [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Bounine, Alexandre
4 siblings, 1 reply; 18+ messages in thread
From: Liu Gang @ 2011-11-12 12:02 UTC (permalink / raw)
To: linuxppc-dev, Alexandre.Bounine
Cc: Jin Qing, r58472, r61911, linux-kernel, Liu Gang, akpm, B11780
This document is created for powerpc rapidio and rmu nodes in dts file.
These nodes can support two rapidio ports and message units. In addition,
It explicates the properties and gives examples about rapidio and rmu nodes.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
.../devicetree/bindings/powerpc/fsl/srio-rmu.txt | 163 ++++++++++++++++++++
.../devicetree/bindings/powerpc/fsl/srio.txt | 103 ++++++++++++
2 files changed, 266 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt
create mode 100644 Documentation/devicetree/bindings/powerpc/fsl/srio.txt
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt
new file mode 100644
index 0000000..b9a8a2b
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt
@@ -0,0 +1,163 @@
+Message unit node:
+
+For SRIO controllers that implement the message unit as part of the controller
+this node is required. For devices with RMAN this node should NOT exist. The
+node is composed of three types of sub-nodes ("fsl-srio-msg-unit",
+"fsl-srio-dbell-unit" and "fsl-srio-port-write-unit").
+
+See srio.txt for more details about generic SRIO controller details.
+
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include "fsl,srio-rmu-vX.Y", "fsl,srio-rmu".
+
+ The version X.Y should match the general SRIO controller's IP Block
+ revision register's Major(X) and Minor (Y) value.
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers for message units
+ and doorbell units.
+
+ - fsl,liodn
+ Usage: optional-but-recommended (for devices with PAMU)
+ Value type: <prop-encoded-array>
+ Definition: The logical I/O device number for the PAMU (IOMMU) to be
+ correctly configured for SRIO accesses. The property should
+ not exist on devices that do not support PAMU.
+
+ The LIODN value is associated with all RMU transactions
+ (msg-unit, doorbell, port-write).
+
+Sub-Nodes for RMU: The RMU node is composed of multiple sub-nodes that
+correspond to the actual sub-controllers in the RMU. The manual for a given
+SoC will detail which and how many of these sub-controllers are implemented.
+
+Message Unit:
+
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include "fsl,srio-msg-unit-vX.Y", "fsl,srio-msg-unit".
+
+ The version X.Y should match the general SRIO controller's IP Block
+ revision register's Major(X) and Minor (Y) value.
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers for message units
+ and doorbell units.
+
+ - interrupts
+ Usage: required
+ Value type: <prop_encoded-array>
+ Definition: Specifies the interrupts generated by this device. The
+ value of the interrupts property consists of one interrupt
+ specifier. The format of the specifier is defined by the
+ binding document describing the node's interrupt parent.
+
+ A pair of IRQs are specified in this property. The first
+ element is associated with the transmit (TX) interrupt and the
+ second element is associated with the receive (RX) interrupt.
+
+Doorbell Unit:
+
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include:
+ "fsl,srio-dbell-unit-vX.Y", "fsl,srio-dbell-unit"
+
+ The version X.Y should match the general SRIO controller's IP Block
+ revision register's Major(X) and Minor (Y) value.
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers for message units
+ and doorbell units.
+
+ - interrupts
+ Usage: required
+ Value type: <prop_encoded-array>
+ Definition: Specifies the interrupts generated by this device. The
+ value of the interrupts property consists of one interrupt
+ specifier. The format of the specifier is defined by the
+ binding document describing the node's interrupt parent.
+
+ A pair of IRQs are specified in this property. The first
+ element is associated with the transmit (TX) interrupt and the
+ second element is associated with the receive (RX) interrupt.
+
+Port-Write Unit:
+
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include:
+ "fsl,srio-port-write-unit-vX.Y", "fsl,srio-port-write-unit"
+
+ The version X.Y should match the general SRIO controller's IP Block
+ revision register's Major(X) and Minor (Y) value.
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers for message units
+ and doorbell units.
+
+ - interrupts
+ Usage: required
+ Value type: <prop_encoded-array>
+ Definition: Specifies the interrupts generated by this device. The
+ value of the interrupts property consists of one interrupt
+ specifier. The format of the specifier is defined by the
+ binding document describing the node's interrupt parent.
+
+ A single IRQ that handles port-write conditions is
+ specified by this property. (Typically shared with error).
+
+ Note: All other standard properties (see the ePAPR) are allowed
+ but are optional.
+
+Example:
+ rmu: rmu@d3000 {
+ compatible = "fsl,srio-rmu";
+ reg = <0xd3000 0x400>;
+ ranges = <0x0 0xd3000 0x400>;
+ fsl,liodn = <0xc8>;
+
+ message-unit@0 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x0 0x100>;
+ interrupts = <
+ 60 2 0 0 /* msg1_tx_irq */
+ 61 2 0 0>;/* msg1_rx_irq */
+ };
+ message-unit@100 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x100 0x100>;
+ interrupts = <
+ 62 2 0 0 /* msg2_tx_irq */
+ 63 2 0 0>;/* msg2_rx_irq */
+ };
+ doorbell-unit@400 {
+ compatible = "fsl,srio-dbell-unit";
+ reg = <0x400 0x80>;
+ interrupts = <
+ 56 2 0 0 /* bell_outb_irq */
+ 57 2 0 0>;/* bell_inb_irq */
+ };
+ port-write-unit@4e0 {
+ compatible = "fsl,srio-port-write-unit";
+ reg = <0x4e0 0x20>;
+ interrupts = <16 2 1 11>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt
new file mode 100644
index 0000000..b039bcb
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt
@@ -0,0 +1,103 @@
+* Freescale Serial RapidIO (SRIO) Controller
+
+RapidIO port node:
+Properties:
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include "fsl,srio" for IP blocks with IP Block
+ Revision Register (SRIO IPBRR1) Major ID equal to 0x01c0.
+
+ Optionally, a compatiable string of "fsl,srio-vX.Y" where X is Major
+ version in IP Block Revision Register and Y is Minor version. If this
+ compatiable is provided it should be ordered before "fsl,srio".
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers. The size should
+ be set to 0x11000.
+
+ - interrupts
+ Usage: required
+ Value type: <prop_encoded-array>
+ Definition: Specifies the interrupts generated by this device. The
+ value of the interrupts property consists of one interrupt
+ specifier. The format of the specifier is defined by the
+ binding document describing the node's interrupt parent.
+
+ A single IRQ that handles error conditions is specified by this
+ property. (Typically shared with port-write).
+
+ - fsl,srio-rmu-handle:
+ Usage: required if rmu node is defined
+ Value type: <phandle>
+ Definition: A single <phandle> value that points to the RMU.
+ (See srio-rmu.txt for more details on RMU node binding)
+
+Port Child Nodes: There should a port child node for each port that exists in
+the controller. The ports are numbered starting at one (1) and should have
+the following properties:
+
+ - cell-index
+ Usage: required
+ Value type: <u32>
+ Definition: A standard property. Matches the port id.
+
+ - ranges
+ Usage: required if local access windows preset
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Utilized to describe the memory mapped
+ IO space utilized by the controller. This corresponds to the
+ setting of the local access windows that are targeted to this
+ SRIO port.
+
+ - fsl,liodn
+ Usage: optional-but-recommended (for devices with PAMU)
+ Value type: <prop-encoded-array>
+ Definition: The logical I/O device number for the PAMU (IOMMU) to be
+ correctly configured for SRIO accesses. The property should
+ not exist on devices that do not support PAMU.
+
+ For HW (ie, the P4080) that only supports a LIODN for both
+ memory and maintenance transactions then a single LIODN is
+ represented in the property for both transactions.
+
+ For HW (ie, the P304x/P5020, etc) that supports an LIODN for
+ memory transactions and a unique LIODN for maintenance
+ transactions then a pair of LIODNs are represented in the
+ property. Within the pair, the first element represents the
+ LIODN associated with memory transactions and the second element
+ represents the LIODN associated with maintenance transactions
+ for the port.
+
+Note: All other standard properties (see ePAPR) are allowed but are optional.
+
+Example:
+
+ rapidio: rapidio@ffe0c0000 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+ compatible = "fsl,srio";
+ interrupts = <16 2 1 11>; /* err_irq */
+ fsl,srio-rmu-handle = <&rmu>;
+ ranges;
+
+ port1 {
+ cell-index = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ fsl,liodn = <34>;
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+
+ port2 {
+ cell-index = <2>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ fsl,liodn = <48>;
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
+ };
--
1.7.3.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* RE: [PATCH 5/5, v3] powerpc/fsl: Document rapidio node binding-information
2011-11-12 12:02 ` [PATCH 5/5, v3] powerpc/fsl: Document rapidio node binding-information Liu Gang
@ 2011-11-16 13:49 ` Bounine, Alexandre
2011-11-16 15:31 ` Kumar Gala
0 siblings, 1 reply; 18+ messages in thread
From: Bounine, Alexandre @ 2011-11-16 13:49 UTC (permalink / raw)
To: Liu Gang, linuxppc-dev
Cc: Jin Qing, r58472, r61911, linux-kernel, akpm, B11780
> -----Original Message-----
> From: Liu Gang [mailto:Gang.Liu@freescale.com]
> Sent: Saturday, November 12, 2011 7:03 AM
> To: linuxppc-dev@lists.ozlabs.org; Bounine, Alexandre
> Cc: akpm@linux-foundation.org; linux-kernel@vger.kernel.org;
> r58472@freescale.com; B11780@freescale.com; r61911@freescale.com; Liu
> Gang; Li Yang; Jin Qing; Kumar Gala
> Subject: [PATCH 5/5,v3] powerpc/fsl: Document rapidio node binding-
> information
>=20
> This document is created for powerpc rapidio and rmu nodes in dts
file.
> These nodes can support two rapidio ports and message units. In
> addition,
> It explicates the properties and gives examples about rapidio and rmu
> nodes.
>=20
> Signed-off-by: Li Yang <leoli@freescale.com>
> Signed-off-by: Jin Qing <b24347@freescale.com>
> Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> .../devicetree/bindings/powerpc/fsl/srio-rmu.txt | 163
> ++++++++++++++++++++
> .../devicetree/bindings/powerpc/fsl/srio.txt | 103
++++++++++++
> 2 files changed, 266 insertions(+), 0 deletions(-)
> create mode 100644
Documentation/devicetree/bindings/powerpc/fsl/srio-
> rmu.txt
> create mode 100644
> Documentation/devicetree/bindings/powerpc/fsl/srio.txt
>=20
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 5/5, v3] powerpc/fsl: Document rapidio node binding-information
2011-11-16 13:49 ` Bounine, Alexandre
@ 2011-11-16 15:31 ` Kumar Gala
0 siblings, 0 replies; 18+ messages in thread
From: Kumar Gala @ 2011-11-16 15:31 UTC (permalink / raw)
To: Bounine, Alexandre
Cc: Jin Qing, r58472, linux-kernel, r61911, Liu Gang, B11780,
linuxppc-dev, akpm
On Nov 16, 2011, at 7:49 AM, Bounine, Alexandre wrote:
>> -----Original Message-----
>> From: Liu Gang [mailto:Gang.Liu@freescale.com]
>> Sent: Saturday, November 12, 2011 7:03 AM
>> To: linuxppc-dev@lists.ozlabs.org; Bounine, Alexandre
>> Cc: akpm@linux-foundation.org; linux-kernel@vger.kernel.org;
>> r58472@freescale.com; B11780@freescale.com; r61911@freescale.com; Liu
>> Gang; Li Yang; Jin Qing; Kumar Gala
>> Subject: [PATCH 5/5,v3] powerpc/fsl: Document rapidio node binding-
>> information
>>
>> This document is created for powerpc rapidio and rmu nodes in dts
> file.
>> These nodes can support two rapidio ports and message units. In
>> addition,
>> It explicates the properties and gives examples about rapidio and rmu
>> nodes.
>>
>> Signed-off-by: Li Yang <leoli@freescale.com>
>> Signed-off-by: Jin Qing <b24347@freescale.com>
>> Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
>> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
>> ---
>> .../devicetree/bindings/powerpc/fsl/srio-rmu.txt | 163
>> ++++++++++++++++++++
>> .../devicetree/bindings/powerpc/fsl/srio.txt | 103
> ++++++++++++
>> 2 files changed, 266 insertions(+), 0 deletions(-)
>> create mode 100644
> Documentation/devicetree/bindings/powerpc/fsl/srio-
>> rmu.txt
>> create mode 100644
>> Documentation/devicetree/bindings/powerpc/fsl/srio.txt
>>
>
> Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
applied to 'next'
- k
^ permalink raw reply [flat|nested] 18+ messages in thread
* RE: [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit
2011-11-12 12:02 [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Liu Gang
` (3 preceding siblings ...)
2011-11-12 12:02 ` [PATCH 5/5, v3] powerpc/fsl: Document rapidio node binding-information Liu Gang
@ 2011-11-16 13:36 ` Bounine, Alexandre
2011-11-16 15:33 ` Kumar Gala
4 siblings, 1 reply; 18+ messages in thread
From: Bounine, Alexandre @ 2011-11-16 13:36 UTC (permalink / raw)
To: Liu Gang, linuxppc-dev
Cc: r58472, r61911, linux-kernel, Lian Minghuan, akpm, B11780
> -----Original Message-----
> From: Liu Gang [mailto:Gang.Liu@freescale.com]
> Sent: Saturday, November 12, 2011 7:02 AM
> To: linuxppc-dev@lists.ozlabs.org; Bounine, Alexandre
> Cc: akpm@linux-foundation.org; linux-kernel@vger.kernel.org;
> r58472@freescale.com; B11780@freescale.com; r61911@freescale.com; Liu
> Gang; Lian Minghuan; Kumar Gala
> Subject: [PATCH 1/5,v3] fsl-rio: Split rio driver into two parts,
> RapidIO endpoint and message unit
>=20
> The Freescale PowerPC RapidIO controller consists of a RapidIO
endpoint
> and
> a RapidIO message unit(RMU). Or use RapidIO message manager(RMan) to
> replace the RMU in DPAA architecture. Therefore, we should split the
> code
> into two function modules according to the hardware architecture. Add
> new
> struct for RMU module, and new initialization function to set up RMU
> module. This policy is very conducive to adding new module like RMan,
> or
> adding multi-ports or message units support.
>=20
> Signed-off-by: Lian Minghuan <Minghuan.Lian@freescale.com>
> Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> arch/powerpc/sysdev/Makefile | 2 +-
> arch/powerpc/sysdev/fsl_rio.c | 1152
+--------------------------------
> -------
> arch/powerpc/sysdev/fsl_rio.h | 78 +++
> arch/powerpc/sysdev/fsl_rmu.c | 1163
> +++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 1267 insertions(+), 1128 deletions(-)
> create mode 100644 arch/powerpc/sysdev/fsl_rio.h
> create mode 100644 arch/powerpc/sysdev/fsl_rmu.c
>=20
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
^ permalink raw reply [flat|nested] 18+ messages in thread* Re: [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit
2011-11-16 13:36 ` [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Bounine, Alexandre
@ 2011-11-16 15:33 ` Kumar Gala
0 siblings, 0 replies; 18+ messages in thread
From: Kumar Gala @ 2011-11-16 15:33 UTC (permalink / raw)
To: Bounine, Alexandre
Cc: r58472, linux-kernel, r61911, Lian Minghuan, Liu Gang, B11780,
linuxppc-dev, akpm
On Nov 16, 2011, at 7:36 AM, Bounine, Alexandre wrote:
>> -----Original Message-----
>> From: Liu Gang [mailto:Gang.Liu@freescale.com]
>> Sent: Saturday, November 12, 2011 7:02 AM
>> To: linuxppc-dev@lists.ozlabs.org; Bounine, Alexandre
>> Cc: akpm@linux-foundation.org; linux-kernel@vger.kernel.org;
>> r58472@freescale.com; B11780@freescale.com; r61911@freescale.com; Liu
>> Gang; Lian Minghuan; Kumar Gala
>> Subject: [PATCH 1/5,v3] fsl-rio: Split rio driver into two parts,
>> RapidIO endpoint and message unit
>>
>> The Freescale PowerPC RapidIO controller consists of a RapidIO
> endpoint
>> and
>> a RapidIO message unit(RMU). Or use RapidIO message manager(RMan) to
>> replace the RMU in DPAA architecture. Therefore, we should split the
>> code
>> into two function modules according to the hardware architecture. Add
>> new
>> struct for RMU module, and new initialization function to set up RMU
>> module. This policy is very conducive to adding new module like RMan,
>> or
>> adding multi-ports or message units support.
>>
>> Signed-off-by: Lian Minghuan <Minghuan.Lian@freescale.com>
>> Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
>> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
>> ---
>> arch/powerpc/sysdev/Makefile | 2 +-
>> arch/powerpc/sysdev/fsl_rio.c | 1152
> +--------------------------------
>> -------
>> arch/powerpc/sysdev/fsl_rio.h | 78 +++
>> arch/powerpc/sysdev/fsl_rmu.c | 1163
>> +++++++++++++++++++++++++++++++++++++++++
>> 4 files changed, 1267 insertions(+), 1128 deletions(-)
>> create mode 100644 arch/powerpc/sysdev/fsl_rio.h
>> create mode 100644 arch/powerpc/sysdev/fsl_rmu.c
>>
>
> Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
>
applied to 'next'
- k
^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2011-11-16 15:55 UTC | newest]
Thread overview: 18+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-11-12 12:02 [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Liu Gang
2011-11-12 12:02 ` [PATCH 2/5, v3] fsl-rio: Add two ports and rapidio message units support Liu Gang
2011-11-16 13:39 ` Bounine, Alexandre
2011-11-16 15:33 ` Kumar Gala
2011-11-12 12:02 ` [PATCH 3/5,v3] powerpc/85xx: Update SRIO device tree nodes Liu Gang
2011-11-16 13:40 ` Bounine, Alexandre
2011-11-16 15:35 ` Kumar Gala
2011-11-12 12:02 ` [PATCH 4/5, v3] powerpc/8xxx: Update device tree bus probe for new RapidIO node binding Liu Gang
2011-11-14 17:35 ` Scott Wood
2011-11-14 17:37 ` Scott Wood
2011-11-15 3:21 ` Liu Gang-B34182
2011-11-16 13:48 ` Bounine, Alexandre
2011-11-16 15:33 ` Kumar Gala
2011-11-12 12:02 ` [PATCH 5/5, v3] powerpc/fsl: Document rapidio node binding-information Liu Gang
2011-11-16 13:49 ` Bounine, Alexandre
2011-11-16 15:31 ` Kumar Gala
2011-11-16 13:36 ` [PATCH 1/5, v3] fsl-rio: Split rio driver into two parts, RapidIO endpoint and message unit Bounine, Alexandre
2011-11-16 15:33 ` Kumar Gala
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).