* [PATCH 1/2] powerpc/85xx: fix localbus and PCI addresses in the P1022DS 36-bit device tree
@ 2011-12-02 22:08 Timur Tabi
2011-12-02 22:08 ` [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS " Timur Tabi
0 siblings, 1 reply; 9+ messages in thread
From: Timur Tabi @ 2011-12-02 22:08 UTC (permalink / raw)
To: kumar.gala, linuxppc-dev
Fix the PCI buses in the 36-bit device tree for the P1022DS. It was using
values copy-pasted from another device tree.
Also fix the NAND localbus bus address from ffa00000 to ff800000, which is
what U-boot sets it to.
Signed-off-by: Timur Tabi <timur@freescale.com>
---
arch/powerpc/boot/dts/p1022ds.dts | 8 ++++----
1 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/powerpc/boot/dts/p1022ds.dts b/arch/powerpc/boot/dts/p1022ds.dts
index 3e85d8c..a54dd13 100644
--- a/arch/powerpc/boot/dts/p1022ds.dts
+++ b/arch/powerpc/boot/dts/p1022ds.dts
@@ -21,7 +21,7 @@
reg = <0xf 0xffe05000 0 0x1000>;
ranges = <0x0 0x0 0xf 0xe8000000 0x08000000
0x1 0x0 0xf 0xe0000000 0x08000000
- 0x2 0x0 0xf 0xffa00000 0x00040000
+ 0x2 0x0 0xf 0xff800000 0x00040000
0x3 0x0 0xf 0xffdf0000 0x00008000>;
/*
@@ -222,7 +222,7 @@
pci0: pcie@fffe09000 {
reg = <0xf 0xffe09000 0 0x1000>;
- ranges = <0x2000000 0x0 0xa0000000 0xc 0x20000000 0x0 0x20000000
+ ranges = <0x2000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
pcie@0 {
ranges = <0x2000000 0x0 0xe0000000
@@ -237,7 +237,7 @@
pci1: pcie@fffe0a000 {
reg = <0xf 0xffe0a000 0 0x1000>;
- ranges = <0x2000000 0x0 0xc0000000 0xc 0x40000000 0x0 0x20000000
+ ranges = <0x2000000 0x0 0xe0000000 0xc 0x40000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc20000 0x0 0x10000>;
pcie@0 {
reg = <0x0 0x0 0x0 0x0 0x0>;
@@ -253,7 +253,7 @@
pci2: pcie@fffe0b000 {
reg = <0xf 0xffe0b000 0 0x1000>;
- ranges = <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000
+ ranges = <0x2000000 0x0 0xe0000000 0xc 0x00000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
pcie@0 {
ranges = <0x2000000 0x0 0xe0000000
--
1.7.3.4
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS device tree
2011-12-02 22:08 [PATCH 1/2] powerpc/85xx: fix localbus and PCI addresses in the P1022DS 36-bit device tree Timur Tabi
@ 2011-12-02 22:08 ` Timur Tabi
2011-12-02 22:19 ` Scott Wood
2011-12-02 23:03 ` Kumar Gala
0 siblings, 2 replies; 9+ messages in thread
From: Timur Tabi @ 2011-12-02 22:08 UTC (permalink / raw)
To: kumar.gala, linuxppc-dev
Add a 32-bit version of the device tree for the Freescale P1022DS reference
board.
Signed-off-by: Timur Tabi <timur@freescale.com>
---
arch/powerpc/boot/dts/p1022ds_32b.dts | 270 +++++++++++++++++++++++++++++++++
1 files changed, 270 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1022ds_32b.dts
diff --git a/arch/powerpc/boot/dts/p1022ds_32b.dts b/arch/powerpc/boot/dts/p1022ds_32b.dts
new file mode 100644
index 0000000..18787d9
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1022ds_32b.dts
@@ -0,0 +1,270 @@
+/*
+ * P1022 DS 32-Bit Physical Address Map Device Tree Source
+ *
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "fsl/p1022si-pre.dtsi"
+/ {
+ model = "fsl,P1022DS";
+ compatible = "fsl,P1022DS";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus@ffe05000 {
+ reg = <0x0 0xffe05000 0 0x1000>;
+ ranges = <0x0 0x0 0x0 0xe8000000 0x08000000
+ 0x1 0x0 0x0 0xe0000000 0x08000000
+ 0x2 0x0 0x0 0xff800000 0x00040000
+ 0x3 0x0 0x0 0xffdf0000 0x00008000>;
+
+ /*
+ * This node is used to access the pixis via "indirect" mode,
+ * which is done by writing the pixis register index to chip
+ * select 0 and the value to/from chip select 1. Indirect
+ * mode is the only way to access the pixis when DIU video
+ * is enabled. Note that this assumes that the first column
+ * of the 'ranges' property above is the chip select number.
+ */
+ board-control@0,0 {
+ compatible = "fsl,p1022ds-indirect-pixis";
+ reg = <0x0 0x0 1 /* CS0 */
+ 0x1 0x0 1>; /* CS1 */
+ };
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition@0 {
+ reg = <0x0 0x03000000>;
+ label = "ramdisk-nor";
+ read-only;
+ };
+
+ partition@3000000 {
+ reg = <0x03000000 0x00e00000>;
+ label = "diagnostic-nor";
+ read-only;
+ };
+
+ partition@3e00000 {
+ reg = <0x03e00000 0x00200000>;
+ label = "dink-nor";
+ read-only;
+ };
+
+ partition@4000000 {
+ reg = <0x04000000 0x00400000>;
+ label = "kernel-nor";
+ read-only;
+ };
+
+ partition@4400000 {
+ reg = <0x04400000 0x03b00000>;
+ label = "jffs2-nor";
+ };
+
+ partition@7f00000 {
+ reg = <0x07f00000 0x00080000>;
+ label = "dtb-nor";
+ read-only;
+ };
+
+ partition@7f80000 {
+ reg = <0x07f80000 0x00080000>;
+ label = "u-boot-nor";
+ read-only;
+ };
+ };
+
+ nand@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,elbc-fcm-nand";
+ reg = <0x2 0x0 0x40000>;
+
+ partition@0 {
+ reg = <0x0 0x02000000>;
+ label = "u-boot-nand";
+ read-only;
+ };
+
+ partition@2000000 {
+ reg = <0x02000000 0x10000000>;
+ label = "jffs2-nand";
+ };
+
+ partition@12000000 {
+ reg = <0x12000000 0x10000000>;
+ label = "ramdisk-nand";
+ read-only;
+ };
+
+ partition@22000000 {
+ reg = <0x22000000 0x04000000>;
+ label = "kernel-nand";
+ };
+
+ partition@26000000 {
+ reg = <0x26000000 0x01000000>;
+ label = "dtb-nand";
+ read-only;
+ };
+
+ partition@27000000 {
+ reg = <0x27000000 0x19000000>;
+ label = "reserved-nand";
+ };
+ };
+
+ board-control@3,0 {
+ compatible = "fsl,p1022ds-fpga", "fsl,fpga-ngpixis";
+ reg = <3 0 0x30>;
+ interrupt-parent = <&mpic>;
+ /*
+ * IRQ8 is generated if the "EVENT" switch is pressed
+ * and PX_CTL[EVESEL] is set to 00.
+ */
+ interrupts = <8 8 0 0>;
+ };
+ };
+
+ soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+
+ i2c@3100 {
+ wm8776:codec@1a {
+ compatible = "wlf,wm8776";
+ reg = <0x1a>;
+ /*
+ * clock-frequency will be set by U-Boot if
+ * the clock is enabled.
+ */
+ };
+ };
+
+ spi@7000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+
+ partition@0 {
+ label = "u-boot-spi";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+ partition@100000 {
+ label = "kernel-spi";
+ reg = <0x00100000 0x00500000>;
+ read-only;
+ };
+ partition@600000 {
+ label = "dtb-spi";
+ reg = <0x00600000 0x00100000>;
+ read-only;
+ };
+ partition@700000 {
+ label = "file system-spi";
+ reg = <0x00700000 0x00900000>;
+ };
+ };
+ };
+
+ ssi@15000 {
+ fsl,mode = "i2s-slave";
+ codec-handle = <&wm8776>;
+ fsl,ssi-asynchronous;
+ };
+
+ usb@22000 {
+ phy_type = "ulpi";
+ };
+
+ usb@23000 {
+ status = "disabled";
+ };
+
+ mdio@24000 {
+ phy0: ethernet-phy@0 {
+ interrupts = <3 1 0 0>;
+ reg = <0x1>;
+ };
+ phy1: ethernet-phy@1 {
+ interrupts = <9 1 0 0>;
+ reg = <0x2>;
+ };
+ };
+
+ ethernet@b0000 {
+ phy-handle = <&phy0>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ ethernet@b1000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+ };
+
+ pci0: pcie@ffe09000 {
+ reg = <0x0 0xffe09000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xe0000000 0 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xe0000000 0 0xc0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>;
+ pcie@0 {
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci2: pcie@ffe0b000 {
+ reg = <0 0xffe0b000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xe0000000 0 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "fsl/p1022si-post.dtsi"
--
1.7.3.4
^ permalink raw reply related [flat|nested] 9+ messages in thread* Re: [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS device tree
2011-12-02 22:08 ` [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS " Timur Tabi
@ 2011-12-02 22:19 ` Scott Wood
2011-12-02 22:24 ` Timur Tabi
2011-12-02 23:03 ` Kumar Gala
1 sibling, 1 reply; 9+ messages in thread
From: Scott Wood @ 2011-12-02 22:19 UTC (permalink / raw)
To: Timur Tabi; +Cc: linuxppc-dev, kumar.gala
On 12/02/2011 04:08 PM, Timur Tabi wrote:
> + lbc: localbus@ffe05000 {
> + reg = <0x0 0xffe05000 0 0x1000>;
> + ranges = <0x0 0x0 0x0 0xe8000000 0x08000000
> + 0x1 0x0 0x0 0xe0000000 0x08000000
> + 0x2 0x0 0x0 0xff800000 0x00040000
> + 0x3 0x0 0x0 0xffdf0000 0x00008000>;
> +
> + /*
> + * This node is used to access the pixis via "indirect" mode,
> + * which is done by writing the pixis register index to chip
> + * select 0 and the value to/from chip select 1. Indirect
> + * mode is the only way to access the pixis when DIU video
> + * is enabled. Note that this assumes that the first column
> + * of the 'ranges' property above is the chip select number.
> + */
> + board-control@0,0 {
> + compatible = "fsl,p1022ds-indirect-pixis";
> + reg = <0x0 0x0 1 /* CS0 */
> + 0x1 0x0 1>; /* CS1 */
> + };
> +
> + nor@0,0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "cfi-flash";
> + reg = <0x0 0x0 0x8000000>;
> + bank-width = <2>;
> + device-width = <1>;
[snip]
> + };
> +
> + nand@2,0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "fsl,elbc-fcm-nand";
> + reg = <0x2 0x0 0x40000>;
[snip]
> + };
> + };
> +
> + board-control@3,0 {
> + compatible = "fsl,p1022ds-fpga", "fsl,fpga-ngpixis";
> + reg = <3 0 0x30>;
> + interrupt-parent = <&mpic>;
> + /*
> + * IRQ8 is generated if the "EVENT" switch is pressed
> + * and PX_CTL[EVESEL] is set to 00.
> + */
> + interrupts = <8 8 0 0>;
> + };
> + };
[snip]
> +/include/ "fsl/p1022si-post.dtsi"
Please add something after post to strip simple-bus off of the localbus
node's compatible. Either you have board-control@0,0, or you have the
other stuff (did you ever find out what the situation with NAND is?) --
not both at the same time. Or do you have U-Boot patching in status
updates now?
I realize this isn't a 32-bit versus 36-bit issue, but this seemed as
good a time as any to repeat this complaint. :-)
-Scott
^ permalink raw reply [flat|nested] 9+ messages in thread* Re: [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS device tree
2011-12-02 22:19 ` Scott Wood
@ 2011-12-02 22:24 ` Timur Tabi
2011-12-02 22:34 ` Scott Wood
0 siblings, 1 reply; 9+ messages in thread
From: Timur Tabi @ 2011-12-02 22:24 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev, kumar.gala
Scott Wood wrote:
> Please add something after post to strip simple-bus off of the localbus
> node's compatible. Either you have board-control@0,0, or you have the
> other stuff (did you ever find out what the situation with NAND is?) --
> not both at the same time. Or do you have U-Boot patching in status
> updates now?
I posted a Linux patch that disables the NOR flash node if video needs to be enabled.
http://patchwork.ozlabs.org/patch/126459/
However, I only now notice that Kumar requested some changes.
--
Timur Tabi
Linux kernel developer at Freescale
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS device tree
2011-12-02 22:24 ` Timur Tabi
@ 2011-12-02 22:34 ` Scott Wood
2011-12-02 23:41 ` Timur Tabi
0 siblings, 1 reply; 9+ messages in thread
From: Scott Wood @ 2011-12-02 22:34 UTC (permalink / raw)
To: Timur Tabi; +Cc: linuxppc-dev, kumar.gala
On 12/02/2011 04:24 PM, Timur Tabi wrote:
> Scott Wood wrote:
>
>> Please add something after post to strip simple-bus off of the localbus
>> node's compatible. Either you have board-control@0,0, or you have the
>> other stuff (did you ever find out what the situation with NAND is?) --
>> not both at the same time. Or do you have U-Boot patching in status
>> updates now?
>
> I posted a Linux patch that disables the NOR flash node if video needs to be enabled.
>
> http://patchwork.ozlabs.org/patch/126459/
>
> However, I only now notice that Kumar requested some changes.
Nothing that happens in Linux excuses handing Linux a device tree that
is wrong. That you need special handling in Linux indicates that this
is not a simple-bus.
-Scott
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS device tree
2011-12-02 22:34 ` Scott Wood
@ 2011-12-02 23:41 ` Timur Tabi
2011-12-02 23:50 ` Scott Wood
0 siblings, 1 reply; 9+ messages in thread
From: Timur Tabi @ 2011-12-02 23:41 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev, kumar.gala
Scott Wood wrote:
> Nothing that happens in Linux excuses handing Linux a device tree that
> is wrong. That you need special handling in Linux indicates that this
> is not a simple-bus.
How about this:
diff --git a/arch/powerpc/boot/dts/fsl/p1022si-post.dtsi b/arch/powerpc/boot/dts
index 16239b1..2a62edd 100644
--- a/arch/powerpc/boot/dts/fsl/p1022si-post.dtsi
+++ b/arch/powerpc/boot/dts/fsl/p1022si-post.dtsi
@@ -35,7 +35,11 @@
&lbc {
#address-cells = <2>;
#size-cells = <1>;
- compatible = "fsl,p1022-elbc", "fsl,elbc", "simple-bus";
+ /*
+ * The localbus on the P1022 is not a simple-bus because of the eLBC
+ * pin muxing when the DIU is enabled.
+ */
+ compatible = "fsl,p1022-elbc", "fsl,elbc";
interrupts = <19 2 0 0>;
};
--
Timur Tabi
Linux kernel developer at Freescale
^ permalink raw reply related [flat|nested] 9+ messages in thread* Re: [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS device tree
2011-12-02 23:41 ` Timur Tabi
@ 2011-12-02 23:50 ` Scott Wood
0 siblings, 0 replies; 9+ messages in thread
From: Scott Wood @ 2011-12-02 23:50 UTC (permalink / raw)
To: Timur Tabi; +Cc: linuxppc-dev, kumar.gala
On 12/02/2011 05:41 PM, Timur Tabi wrote:
> Scott Wood wrote:
>
>> Nothing that happens in Linux excuses handing Linux a device tree that
>> is wrong. That you need special handling in Linux indicates that this
>> is not a simple-bus.
>
> How about this:
>
> diff --git a/arch/powerpc/boot/dts/fsl/p1022si-post.dtsi b/arch/powerpc/boot/dts
> index 16239b1..2a62edd 100644
> --- a/arch/powerpc/boot/dts/fsl/p1022si-post.dtsi
> +++ b/arch/powerpc/boot/dts/fsl/p1022si-post.dtsi
> @@ -35,7 +35,11 @@
> &lbc {
> #address-cells = <2>;
> #size-cells = <1>;
> - compatible = "fsl,p1022-elbc", "fsl,elbc", "simple-bus";
> + /*
> + * The localbus on the P1022 is not a simple-bus because of the eLBC
> + * pin muxing when the DIU is enabled.
> + */
> + compatible = "fsl,p1022-elbc", "fsl,elbc";
> interrupts = <19 2 0 0>;
> };
>
OK.
-Scott
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS device tree
2011-12-02 22:08 ` [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS " Timur Tabi
2011-12-02 22:19 ` Scott Wood
@ 2011-12-02 23:03 ` Kumar Gala
2011-12-05 23:44 ` Timur Tabi
1 sibling, 1 reply; 9+ messages in thread
From: Kumar Gala @ 2011-12-02 23:03 UTC (permalink / raw)
To: Timur Tabi; +Cc: linuxppc-dev
On Dec 2, 2011, at 4:08 PM, Timur Tabi wrote:
> Add a 32-bit version of the device tree for the Freescale P1022DS =
reference
> board.
>=20
> Signed-off-by: Timur Tabi <timur@freescale.com>
> ---
> arch/powerpc/boot/dts/p1022ds_32b.dts | 270 =
+++++++++++++++++++++++++++++++++
> 1 files changed, 270 insertions(+), 0 deletions(-)
> create mode 100644 arch/powerpc/boot/dts/p1022ds_32b.dts
look at how mpc8572ds handles 36b.dts we put common definitions in a =
shared file.
- k=
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS device tree
2011-12-02 23:03 ` Kumar Gala
@ 2011-12-05 23:44 ` Timur Tabi
0 siblings, 0 replies; 9+ messages in thread
From: Timur Tabi @ 2011-12-05 23:44 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-dev
Kumar Gala wrote:
> look at how mpc8572ds handles 36b.dts we put common definitions in a shared file.
Ok, I've made those changes, but when I boot the kernel, I'm seeing this. Can you give me a clue as to what's wrong?
PCI: Probing PCI hardware
pci 0000:00:00.0: [1957:0110] type 1 class 0x000b20
pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01)
pci 0000:00:00.0: supports D1 D2
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0001:02:00.0: [1957:0110] type 1 class 0x000b20
pci 0001:02:00.0: ignoring class b20 (doesn't match header type 01)
pci 0001:02:00.0: supports D1 D2
pci 0001:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0001:02:00.0: PME# disabled
pci 0001:02:00.0: PCI bridge to [bus 03-ff]
pci 0002:04:00.0: [1957:0110] type 1 class 0x000b20
pci 0002:04:00.0: ignoring class b20 (doesn't match header type 01)
pci 0002:04:00.0: supports D1 D2
pci 0002:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0002:04:00.0: PME# disabled
pci 0002:05:00.0: [8086:10d3] type 0 class 0x000200
pci 0002:05:00.0: reg 10: [mem 0x80000000-0x8001ffff]
pci 0002:05:00.0: reg 14: [mem 0x80080000-0x800fffff]
pci 0002:05:00.0: reg 18: [io 0x1000-0x101f]
pci 0002:05:00.0: reg 1c: [mem 0x80100000-0x80103fff]
pci 0002:05:00.0: reg 30: [mem 0x00000000-0x0003ffff pref]
pci 0002:05:00.0: PME# supported from D0 D3hot D3cold
pci 0002:05:00.0: PME# disabled
pci 0002:04:00.0: PCI bridge to [bus 05-ff]
pci 0002:04:00.0: bridge window [mem 0x80000000-0x801fffff]
PCI: Cannot allocate resource region 0 of device 0002:05:00.0, will remap
PCI: Cannot allocate resource region 1 of device 0002:05:00.0, will remap
PCI: Cannot allocate resource region 3 of device 0002:05:00.0, will remap
PCI 0000:00 Cannot reserve Legacy IO [io 0xffbed000-0xffbedfff]
PCI 0001:02 Cannot reserve Legacy IO [io 0xffbdb000-0xffbdbfff]
PCI 0002:04 Cannot reserve Legacy IO [io 0xffbc9000-0xffbc9fff]
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0: bridge window [io 0xffbed000-0xffbfcfff]
pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff]
pci 0001:02:00.0: PCI bridge to [bus 03-03]
pci 0001:02:00.0: bridge window [io 0xffbdb000-0xffbeafff]
pci 0001:02:00.0: bridge window [mem 0xc0000000-0xdfffffff]
pci 0002:04:00.0: BAR 9: can't assign mem pref (size 0x100000)
pci 0002:05:00.0: BAR 1: assigned [mem 0x80000000-0x8007ffff]
pci 0002:05:00.0: BAR 1: set to [mem 0x80000000-0x8007ffff] (PCI address [0xe000
0000-0xe007ffff])
pci 0002:05:00.0: BAR 6: assigned [mem 0x80080000-0x800bffff pref]
pci 0002:05:00.0: BAR 0: assigned [mem 0x800c0000-0x800dffff]
pci 0002:05:00.0: BAR 0: set to [mem 0x800c0000-0x800dffff] (PCI address [0xe00c
0000-0xe00dffff])
pci 0002:05:00.0: BAR 3: assigned [mem 0x800e0000-0x800e3fff]
pci 0002:05:00.0: BAR 3: set to [mem 0x800e0000-0x800e3fff] (PCI address [0xe00e
0000-0xe00e3fff])
pci 0002:04:00.0: PCI bridge to [bus 05-05]
pci 0002:04:00.0: bridge window [io 0xffbc9000-0xffbd8fff]
pci 0002:04:00.0: bridge window [mem 0x80000000-0x9fffffff]
pci 0000:00:00.0: enabling device (0106 -> 0107)
pci 0001:02:00.0: enabling device (0106 -> 0107)
pci 0002:04:00.0: enabling device (0106 -> 0107)
pci_bus 0000:00: resource 0 [io 0xffbed000-0xffbfcfff]
pci_bus 0000:00: resource 1 [mem 0xa0000000-0xbfffffff]
pci_bus 0000:01: resource 0 [io 0xffbed000-0xffbfcfff]
pci_bus 0000:01: resource 1 [mem 0xa0000000-0xbfffffff]
pci_bus 0001:02: resource 0 [io 0xffbdb000-0xffbeafff]
pci_bus 0001:02: resource 1 [mem 0xc0000000-0xdfffffff]
pci_bus 0001:03: resource 0 [io 0xffbdb000-0xffbeafff]
pci_bus 0001:03: resource 1 [mem 0xc0000000-0xdfffffff]
pci_bus 0002:04: resource 0 [io 0xffbc9000-0xffbd8fff]
pci_bus 0002:04: resource 1 [mem 0x80000000-0x9fffffff]
pci_bus 0002:05: resource 0 [io 0xffbc9000-0xffbd8fff]
pci_bus 0002:05: resource 1 [mem 0x80000000-0x9fffffff]
--
Timur Tabi
Linux kernel developer at Freescale
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2011-12-05 23:44 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-12-02 22:08 [PATCH 1/2] powerpc/85xx: fix localbus and PCI addresses in the P1022DS 36-bit device tree Timur Tabi
2011-12-02 22:08 ` [PATCH 2/2] powerpc/85xx: add a 32-bit P1022DS " Timur Tabi
2011-12-02 22:19 ` Scott Wood
2011-12-02 22:24 ` Timur Tabi
2011-12-02 22:34 ` Scott Wood
2011-12-02 23:41 ` Timur Tabi
2011-12-02 23:50 ` Scott Wood
2011-12-02 23:03 ` Kumar Gala
2011-12-05 23:44 ` Timur Tabi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).