linuxppc-dev.lists.ozlabs.org archive mirror
 help / color / mirror / Atom feed
* [PATCH] powerpc/85xx:Add BSC9131 RDB Support
@ 2012-03-15  5:37 Prabhakar Kushwaha
  2012-03-16 20:12 ` Kumar Gala
  0 siblings, 1 reply; 3+ messages in thread
From: Prabhakar Kushwaha @ 2012-03-15  5:37 UTC (permalink / raw)
  To: linuxppc-dev, devicetree-discuss
  Cc: Poonam Aggrwal, Priyanka Jain, Ramneek Mehresh, Rajan Srivastava,
	Akhil Goyal, Prabhakar Kushwaha

BSC9131RDB is a Freescale reference design board for BSC9131 SoC.The BSC9131 is
integrated SoC that targets Femto base station market. It combines Power
Architecture e500v2 and DSP StarCore SC3850 core technologies with MAPLE-B2F
baseband acceleration processing elements.

The BSC9131 SoC includes the following function and features:
    . Power Architecture subsystem including a e500 processor with 256-Kbyte shared
      L2 cache
    . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
    . The Multi Accelerator Platform Engine for Femto BaseStation Baseband
      Processing (MAPLE-B2F)
    . A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
      Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
      and CRC algorithms
    . Consists of accelerators for Convolution, Filtering, Turbo Encoding,
      Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
      operations
    . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
      ECC, up to 400-MHz clock/800 MHz data rate
    . Dedicated security engine featuring trusted boot
    . DMA controller
    . OCNDMA with four bidirectional channels
    . Interfaces
    . Two triple-speed Gigabit Ethernet controllers featuring network acceleration
      including IEEE 1588. v2 hardware support and virtualization (eTSEC)
    . eTSEC 1 supports RGMII/RMII
    . eTSEC 2 supports RGMII
    . High-speed USB 2.0 host and device controller with ULPI interface
    . Enhanced secure digital (SD/MMC) host controller (eSDHC)
    . Antenna interface controller (AIC), supporting three industry standard
      JESD207/three custom ADI RF interfaces (two dual port and one single port)
      and three MAXIM's MaxPHY serial interfaces
    . ADI lanes support both full duplex FDD support and half duplex TDD support
    . Universal Subscriber Identity Module (USIM) interface that facilitates
      communication to SIM cards or Eurochip pre-paid phone cards
    . TDM with one TDM port
    . Two DUART, four eSPI, and two I2C controllers
    . Integrated Flash memory controller (IFC)
    . TDM with 256 channels
    . GPIO
    . Sixteen 32-bit timers

The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.

 BSC9131RDB Overview
 ----------------------
     BSC9131 SoC
     1Gbyte DDR3 (on board DDR)
     128Mbyte 2K page size NAND Flash
     256 Kbit M24256 I2C EEPROM
     128 Mbit SPI Flash memory
     USB-ULPI
     eTSEC1: Connected to RGMII PHY
     eTSEC2: Connected to RGMII PHY
     DUART interface: supports one UARTs up to 115200 bps for console display

 Linux runs on e500v2 core and access some DSP peripherals like AIC

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
---
Note:   Name of PSC9131 has been changed to BSC9131 because of new nomenclature
	Please reject earlier patch"powerpc/85xx:Add BSC9131 RDB Support"
	  http://patchwork.ozlabs.org/patch/146349/

 Beased on http://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc.git
	    branch master

 arch/powerpc/boot/dts/bsc9131rdb.dts          |   34 +++++
 arch/powerpc/boot/dts/bsc9131rdb.dtsi         |  179 +++++++++++++++++++++++++
 arch/powerpc/boot/dts/fsl/bsc9131si-post.dtsi |  172 ++++++++++++++++++++++++
 arch/powerpc/boot/dts/fsl/bsc9131si-pre.dtsi  |   59 ++++++++
 arch/powerpc/platforms/85xx/Kconfig           |    9 ++
 arch/powerpc/platforms/85xx/Makefile          |    1 +
 arch/powerpc/platforms/85xx/bsc913x_board.c   |   96 +++++++++++++
 7 files changed, 550 insertions(+), 0 deletions(-)
 create mode 100644 arch/powerpc/boot/dts/bsc9131rdb.dts
 create mode 100644 arch/powerpc/boot/dts/bsc9131rdb.dtsi
 create mode 100644 arch/powerpc/boot/dts/fsl/bsc9131si-post.dtsi
 create mode 100644 arch/powerpc/boot/dts/fsl/bsc9131si-pre.dtsi
 create mode 100644 arch/powerpc/platforms/85xx/bsc913x_board.c

diff --git a/arch/powerpc/boot/dts/bsc9131rdb.dts b/arch/powerpc/boot/dts/bsc9131rdb.dts
new file mode 100644
index 0000000..e13d2d4
--- /dev/null
+++ b/arch/powerpc/boot/dts/bsc9131rdb.dts
@@ -0,0 +1,34 @@
+/*
+ * BSC9131 RDB Device Tree Source
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/include/ "fsl/bsc9131si-pre.dtsi"
+
+/ {
+	model = "fsl,bsc9131rdb";
+	compatible = "fsl,bsc9131rdb";
+
+	memory {
+		device_type = "memory";
+	};
+
+	board_ifc: ifc: ifc@ff71e000 {
+		/* NAND Flash on board */
+		ranges = <0x0 0x0 0x0 0xff800000 0x00004000>;
+		reg = <0x0 0xff71e000 0x0 0x2000>;
+	};
+
+	board_soc: soc: soc@ff700000 {
+		ranges = <0x0 0x0 0xff700000 0x100000>;
+	};
+};
+
+/include/ "bsc9131rdb.dtsi"
+/include/ "fsl/bsc9131si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/bsc9131rdb.dtsi b/arch/powerpc/boot/dts/bsc9131rdb.dtsi
new file mode 100644
index 0000000..d274c014
--- /dev/null
+++ b/arch/powerpc/boot/dts/bsc9131rdb.dtsi
@@ -0,0 +1,179 @@
+/*
+ * BSC9131 RDB Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&board_ifc {
+
+	nand@0,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,ifc-nand";
+		reg = <0x0 0x0 0x4000>;
+
+		partition@0 {
+			/* This location must not be altered  */
+			/* 3MB for u-boot Bootloader Image */
+			reg = <0x0 0x00300000>;
+			label = "NAND U-Boot Image";
+			read-only;
+		};
+
+		partition@300000 {
+			/* 1MB for DTB Image */
+			reg = <0x00300000 0x00100000>;
+			label = "NAND DTB Image";
+		};
+
+		partition@400000 {
+			/* 8MB for Linux Kernel Image */
+			reg = <0x00400000 0x00800000>;
+			label = "NAND Linux Kernel Image";
+		};
+
+		partition@c00000 {
+			/* Rest space for Root file System Image */
+			reg = <0x00c00000 0x07400000>;
+			label = " NAND RFS Image";
+		};
+	};
+};
+
+&board_soc {
+	i2c@3000 {
+		gpio3: gpio@21 {
+			compatible = "nxp,pca9555";
+			reg = <0x21>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			polarity = <0x00>;
+		};
+		gpio4: gpio@23 {
+			compatible = "nxp,pca9555";
+			reg = <0x23>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			polarity = <0x00>;
+		};
+		gpio5: gpio@27 {
+			compatible = "nxp,pca9555";
+			reg = <0x27>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			polarity = <0x00>;
+		};
+		hwmon@4c {
+			compatible = "adi,adt7461";
+			reg = <0x4c>;
+		};
+		eeprom@52 {
+			compatible = "st-micro,24c02";
+			reg = <0x52>;
+		};
+	};
+
+	/* BSC9131RDB does not have any device on i2c@3100 */
+	i2c@3100 {
+		status = "disabled";
+	};
+
+	spi@7000 {
+		flash@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "spansion,s25sl12801";
+			reg = <0>;
+			spi-max-frequency = <50000000>;
+
+			/* 512KB for u-boot Bootloader Image */
+			partition@0 {
+				reg = <0x0 0x00080000>;
+				label = "SPI Flash U-Boot Image";
+				read-only;
+			};
+
+			/* 512KB for DTB Image */
+			partition@80000 {
+				reg = <0x00080000 0x00080000>;
+				label = "SPI Flash DTB Image";
+			};
+
+			/* 4MB for Linux Kernel Image */
+			partition@100000 {
+				reg = <0x00100000 0x00400000>;
+				label = "SPI Flash Kernel Image";
+			};
+
+			/* 4MB for Compressed RFS Image */
+			partition@500000 {
+				reg = <0x00500000 0x00400000>;
+				label = "SPI Flash Compressed RFS Image";
+			};
+
+			/* 7MB for JFFS2 based RFS */
+			partition@900000 {
+				reg = <0x00900000 0x00700000>;
+				label = "SPI Flash JFFS2 RFS Image";
+			};
+		};
+	};
+
+	usb@22000 {
+		phy_type = "ulpi";
+	};
+
+	mdio@24000 {
+		phy0: ethernet-phy@0 {
+			interrupts = <3 1 0 0>;
+			reg = <0x0>;
+		};
+
+		phy1: ethernet-phy@1 {
+			interrupts = <2 1 0 0>;
+			reg = <0x3>;
+		};
+	};
+
+	sdhci@2e000 {
+		status = "disabled";
+	};
+
+	enet0: ethernet@b0000 {
+		phy-handle = <&phy0>;
+		phy-connection-type = "rgmii-id";
+	};
+
+	enet1: ethernet@b1000 {
+		phy-handle = <&phy1>;
+		phy-connection-type = "rgmii-id";
+	};
+};
diff --git a/arch/powerpc/boot/dts/fsl/bsc9131si-post.dtsi b/arch/powerpc/boot/dts/fsl/bsc9131si-post.dtsi
new file mode 100644
index 0000000..513a652
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/bsc9131si-post.dtsi
@@ -0,0 +1,172 @@
+/*
+ * BSC9131 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,ifc", "simple-bus";
+	interrupts = <16 2 0 0 20 2 0 0>;
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,bsc9131-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,bsc9131-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,bsc9131-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+	i2c@3000 {
+		interrupts = <17 2 0 0>;
+	};
+
+/include/ "pq3-i2c-1.dtsi"
+	i2c@3100 {
+		interrupts = <17 2 0 0>;
+	};
+
+/include/ "pq3-duart-0.dtsi"
+	serial0: serial@4500 {
+		interrupts = <18 2 0 0>;
+	};
+
+	serial1: serial@4600 {
+		interrupts = <18 2 0 0 >;
+	};
+/include/ "pq3-espi-0.dtsi"
+	spi0: spi@7000 {
+		fsl,espi-num-chipselects = <1>;
+		interrupts = <22 0x2 0 0>;
+	};
+
+/include/ "pq3-gpio-0.dtsi"
+	gpio-controller@f000 {
+		interrupts = <19 0x2 0 0>;
+		};
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,bsc9131-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x40000>; // L2,256K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+
+dma@21300 {
+
+	dma-channel@0 {
+		interrupts = <62 2 0 0>;
+	};
+
+	dma-channel@80 {
+		interrupts = <63 2 0 0>;
+	};
+
+	dma-channel@100 {
+		interrupts = <64 2 0 0>;
+	};
+
+	dma-channel@180 {
+		interrupts = <65 2 0 0>;
+	};
+};
+
+/include/ "pq3-usb2-dr-0.dtsi"
+usb@22000 {
+	compatible = "fsl-usb2-dr","fsl-usb2-dr-v2.2";
+	interrupts = <40 0x2 0 0>;
+};
+
+/include/ "pq3-esdhc-0.dtsi"
+	sdhc@2e000 {
+		fsl,sdhci-auto-cmd12;
+		interrupts = <41 0x2 0 0>;
+	};
+
+/include/ "pq3-mpic.dtsi"
+
+timer@41100 {
+	compatible = "fsl,mpic-v1.2-msgr", "fsl,mpic-msg";
+	reg = <0x41400 0x200>;
+	interrupts = <
+		0xb0 2
+		0xb1 2
+		0xb2 2
+		0xb3 2>;
+};
+
+/include/ "pq3-etsec2-0.dtsi"
+enet0: ethernet@b0000 {
+	queue-group@b0000 {
+		fsl,rx-bit-map = <0xff>;
+		fsl,tx-bit-map = <0xff>;
+		interrupts = <26 2 0 0 27 2 0 0 28 2 0 0>;
+	};
+};
+
+/include/ "pq3-etsec2-1.dtsi"
+enet1: ethernet@b1000 {
+	queue-group@b1000 {
+		fsl,rx-bit-map = <0xff>;
+		fsl,tx-bit-map = <0xff>;
+		interrupts = <33 2 0 0 34 2 0 0 35 2 0 0>;
+	};
+};
+
+global-utilities@e0000 {
+		compatible = "fsl,bsc9131-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};
diff --git a/arch/powerpc/boot/dts/fsl/bsc9131si-pre.dtsi b/arch/powerpc/boot/dts/fsl/bsc9131si-pre.dtsi
new file mode 100644
index 0000000..743e4ae
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/bsc9131si-pre.dtsi
@@ -0,0 +1,59 @@
+/*
+ * BSC9131 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,BSC9131";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,BSC9131@0 {
+			device_type = "cpu";
+			compatible = "fsl,e500v2";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+	};
+};
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index d7946be..9fb5b03 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -91,6 +91,15 @@ config P1023_RDS
 	help
 	  This option enables support for the P1023 RDS board
 
+config BSC9131_RDB
+	bool "Freescale BSC9131RDB"
+	select DEFAULT_UIMAGE
+	help
+	  This option enables support for the Freescale BSC9131RDB board.
+	  The BSC9131 is a heterogeneous SoC containing an e500v2 powerpc and a
+	  StarCore SC3850 DSP
+	  Manufacturer : Freescale Semiconductor, Inc
+
 config SOCRATES
 	bool "Socrates"
 	select DEFAULT_UIMAGE
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index 9cb2d43..25b376c 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_P3041_DS)    += p3041_ds.o corenet_ds.o
 obj-$(CONFIG_P3060_QDS)   += p3060_qds.o corenet_ds.o
 obj-$(CONFIG_P4080_DS)    += p4080_ds.o corenet_ds.o
 obj-$(CONFIG_P5020_DS)    += p5020_ds.o corenet_ds.o
+obj-$(CONFIG_BSC9131_RDB) += bsc913x_board.o
 obj-$(CONFIG_STX_GP3)	  += stx_gp3.o
 obj-$(CONFIG_TQM85xx)	  += tqm85xx.o
 obj-$(CONFIG_SBC8560)     += sbc8560.o
diff --git a/arch/powerpc/platforms/85xx/bsc913x_board.c b/arch/powerpc/platforms/85xx/bsc913x_board.c
new file mode 100644
index 0000000..934c3b5
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/bsc913x_board.c
@@ -0,0 +1,96 @@
+/*
+ * BSC9131RDB Board Setup
+ *
+ * Author: Priyanka Jain <Priyanka.Jain@freescale.com>
+ *
+ * Copyright 2011-2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <asm/mpic.h>
+#include <sysdev/fsl_soc.h>
+#include <asm/udbg.h>
+
+void __init bsc913x_board_pic_init(void)
+{
+	struct mpic *mpic;
+	struct resource r;
+	struct device_node *np;
+
+	np = of_find_node_by_type(NULL, "open-pic");
+	if (!np) {
+		pr_err("bsc913x: Could not find open-pic node\n");
+		return;
+	}
+
+	if (of_address_to_resource(np, 0, &r)) {
+		pr_err("bsc913x: Failed to map mpic register space\n");
+		of_node_put(np);
+		return;
+	}
+
+	mpic = mpic_alloc(np, r.start, MPIC_WANTS_RESET |
+	  MPIC_BIG_ENDIAN | MPIC_BROKEN_FRR_NIRQS | MPIC_SINGLE_DEST_CPU,
+	  0, 256, " OpenPIC  ");
+
+	of_node_put(np);
+
+	if (!mpic)
+		pr_err("bsc913x: Failed to allocate MPIC structure\n");
+	else
+		mpic_init(mpic);
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init bsc913x_board_setup_arch(void)
+{
+	if (ppc_md.progress)
+		ppc_md.progress("bsc913x_board_setup_arch()", 0);
+
+	pr_info("bsc913x board from Freescale Semiconductor\n");
+}
+
+static struct of_device_id __initdata bsc913x_board_ids[] = {
+	{ .type = "soc", },
+	{ .type = "dsp", },
+	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
+	{ .compatible = "gianfar", },
+	{},
+};
+
+static int __init bsc913x_board_publish_devices(void)
+{
+	return of_platform_bus_probe(NULL, bsc913x_board_ids, NULL);
+}
+machine_device_initcall(bsc9131_rdb, bsc913x_board_publish_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+
+static int __init bsc9131_rdb_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+
+	return of_flat_dt_is_compatible(root, "fsl,bsc9131rdb");
+}
+
+define_machine(bsc9131_rdb) {
+	.name			= "BSC9131 RDB",
+	.probe			= bsc9131_rdb_probe,
+	.setup_arch		= bsc913x_board_setup_arch,
+	.init_IRQ		= bsc913x_board_pic_init,
+	.get_irq		= mpic_get_irq,
+	.restart		= fsl_rstcr_restart,
+	.calibrate_decr		= generic_calibrate_decr,
+	.progress		= udbg_progress,
+};
-- 
1.7.5.4

^ permalink raw reply related	[flat|nested] 3+ messages in thread
end of thread, other threads:[~2012-03-17  3:42 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-03-15  5:37 [PATCH] powerpc/85xx:Add BSC9131 RDB Support Prabhakar Kushwaha
2012-03-16 20:12 ` Kumar Gala
2012-03-17  3:42   ` Kushwaha Prabhakar-B32579

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).