* [PATCH][v10] powerpc/mpc85xx:Add initial device tree support of T104x
@ 2014-04-21 11:34 Prabhakar Kushwaha
2014-06-06 5:04 ` [linuxppc-release] " Shengzhou.Liu
0 siblings, 1 reply; 3+ messages in thread
From: Prabhakar Kushwaha @ 2014-04-21 11:34 UTC (permalink / raw)
To: linuxppc-dev
Cc: scottwood, Priyanka Jain, Poonam Aggrwal, Prabhakar Kushwaha,
Varun Sethi
The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
processor cores with high-performance data path acceleration architecture
and network peripheral interfaces required for networking & telecommunications.
T1042 personality is a reduced personality of T1040 without Integrated 8-port
Gigabit Ethernet switch.
The T1040/T1042 SoC includes the following function and features:
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration (SEC 5.0)
- RegEx Pattern Matching Acceleration (PME 2.2)
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch (T1040 only)
- Four 1 Gbps Ethernet controllers
- Two RGMII interfaces or one RGMII and one MII interfaces
- High speed peripheral interfaces
- Four PCI Express 2.0 controllers running at up to 5 GHz
- Two SATA controllers supporting 1.5 and 3.0 Gb/s operation
- Upto two QSGMII interface
- Upto six SGMII interface supporting 1000 Mbps
- One SGMII interface supporting upto 2500 Mbps
- Additional peripheral interfaces
- Two USB 2.0 controllers with integrated PHY
- SD/eSDHC/eMMC
- eSPI controller
- Four I2C controllers
- Four UARTs
- Four GPIO controllers
- Integrated flash controller (IFC)
- Change this to LCD/ HDMI interface (DIU) with 12 bit dual data rate
- TDM interface
- Multicore programmable interrupt controller (PIC)
- Two 8-channel DMA engines
- Single source clocking implementation
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
---
Changes for v2: Incorporated Scott's comments
- Update t1040si-post.dtsi
- update clock device tree node as per
http://patchwork.ozlabs.org/patch/274134/
- removed DMA node, It will be added later as per
http://patchwork.ozlabs.org/patch/271238/
- Updated display compatible field
Changes for v3: Incorporated Scott's comments
- Updated soc compatible field
- updated clock compatible field
Changes for v4: Sending as it is
Changes for v5: Sending as it is
Changes for v6: Updated branch of creation
Changes for v7: Incororated Scott's commetns
- Create patch set
- remove whitespace
- Removed l2switch. It will be added later
Changes for v8: Incorporated Scott's comments
- Added comment line in T1042si-post.dtsi
- removed extra lines
Changes for v9:
- updated clock node as per new bindings
- removed extra line
- added dma node
Changes for v10:
- update corenet compatible
- remove clock frequency from dts file
- fix white space
arch/powerpc/boot/dts/fsl/t1040si-post.dtsi | 430 +++++++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/t1042si-post.dtsi | 37 +++
arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi | 104 +++++++
3 files changed, 571 insertions(+)
create mode 100644 arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t1042si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
new file mode 100644
index 0000000..2cae320
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
@@ -0,0 +1,430 @@
+/*
+ * T1040 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc", "simple-bus";
+ interrupts = <25 2 0 0>;
+};
+
+&pci0 {
+ compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <20 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <20 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+&pci1 {
+ compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ interrupts = <21 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <21 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+&pci2 {
+ compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <22 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <22 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+&pci3 {
+ compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <23 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <23 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 43 1 0 0
+ 0000 0 0 2 &mpic 0 1 0 0
+ 0000 0 0 3 &mpic 4 1 0 0
+ 0000 0 0 4 &mpic 8 1 0 0
+ >;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,t1040-dcsr-epu", "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,t1040-dcsr-cnpc", "fsl,dcsr-cnpc";
+ reg = <0x1000 0x1000 0x1002000 0x10000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0x1A000 0x1000>;
+ };
+ dcsr-dpaa@9000 {
+ compatible = "fsl,t1040-dcsr-dpaa", "fsl,dcsr-dpaa";
+ reg = <0x9000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,t1040-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,t1040-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,t1040-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-snpc@30000 {
+ compatible = "fsl,t1040-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x30000 0x1000 0x1022000 0x10000>;
+ };
+ dcsr-snpc@31000 {
+ compatible = "fsl,t1040-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x31000 0x1000 0x1042000 0x10000>;
+ };
+ dcsr-cpu-sb-proxy@100000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x100000 0x1000 0x101000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@108000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x108000 0x1000 0x109000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@110000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu2>;
+ reg = <0x110000 0x1000 0x111000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@118000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu3>;
+ reg = <0x118000 0x1000 0x119000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <16>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v5.0",
+ "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,t1040-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000>;
+ interrupts = <16 2 1 27>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet2-cf", "fsl,corenet-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x1000>;
+ ranges = <0 0x20000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ pamu0: pamu@0 {
+ reg = <0 0x1000>;
+ fsl,primary-cache-geometry = <128 1>;
+ fsl,secondary-cache-geometry = <16 2>;
+ };
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,t1040-device-config", "fsl,qoriq-device-config-2.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ fsl,liodn-bits = <12>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,t1040-clockgen", "fsl,qoriq-clockgen-2.0";
+ ranges = <0x0 0xe1000 0x1000>;
+ reg = <0xe1000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ sysclk: sysclk {
+ #clock-cells = <0>;
+ compatible = "fsl,qoriq-sysclk-2.0";
+ clock-output-names = "sysclk", "fixed-clock";
+ };
+
+
+ pll0: pll0@800 {
+ #clock-cells = <1>;
+ reg = <0x800 4>;
+ compatible = "fsl,qoriq-core-pll-2.0";
+ clocks = <&sysclk>;
+ clock-output-names = "pll0", "pll0-div2", "pll0-div4";
+ };
+
+ pll1: pll1@820 {
+ #clock-cells = <1>;
+ reg = <0x820 4>;
+ compatible = "fsl,qoriq-core-pll-2.0";
+ clocks = <&sysclk>;
+ clock-output-names = "pll1", "pll1-div2", "pll1-div4";
+ };
+
+ mux0: mux0@0 {
+ #clock-cells = <0>;
+ reg = <0x0 4>;
+ compatible = "fsl,qoriq-core-mux-2.0";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0", "pll0-div2", "pll1-div4",
+ "pll1", "pll1-div2", "pll1-div4";
+ clock-output-names = "cmux0";
+ };
+
+ mux1: mux1@20 {
+ #clock-cells = <0>;
+ reg = <0x20 4>;
+ compatible = "fsl,qoriq-core-mux-2.0";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0", "pll0-div2", "pll1-div4",
+ "pll1", "pll1-div2", "pll1-div4";
+ clock-output-names = "cmux1";
+ };
+
+ mux2: mux2@40 {
+ #clock-cells = <0>;
+ reg = <0x40 4>;
+ compatible = "fsl,qoriq-core-mux-2.0";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0", "pll0-div2", "pll1-div4",
+ "pll1", "pll1-div2", "pll1-div4";
+ clock-output-names = "cmux2";
+ };
+
+ mux3: mux3@60 {
+ #clock-cells = <0>;
+ reg = <0x60 4>;
+ compatible = "fsl,qoriq-core-mux-2.0";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0_0", "pll0_1", "pll0_2",
+ "pll1_0", "pll1_1", "pll1_2";
+ clock-output-names = "cmux3";
+ };
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,t1040-rcpm", "fsl,qoriq-rcpm-2.0";
+ reg = <0xe2000 0x1000>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,t1040-sfp";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,t1040-serdes";
+ reg = <0xea000 0x4000>;
+ };
+
+/include/ "elo3-dma-0.dtsi"
+/include/ "elo3-dma-1.dtsi"
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ compatible = "fsl,t1040-esdhc", "fsl,esdhc";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x530>; /* eSDHCLIODNR */
+ sdhci,auto-cmd12;
+ };
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-gpio-1.dtsi"
+/include/ "qoriq-gpio-2.dtsi"
+/include/ "qoriq-gpio-3.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ compatible = "fsl-usb2-mph-v2.4", "fsl-usb2-mph";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x520>; /* USB1LIODNR */
+ phy_type = "utmi";
+ port0;
+ };
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ compatible = "fsl-usb2-dr-v2.4", "fsl-usb2-dr";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x524>; /* USB2LIODNR */
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+
+ display@180000 {
+ compatible = "fsl,t1040-diu", "fsl,diu";
+ reg = <0x180000 1000>;
+ interrupts = <74 2 0 0>;
+ };
+
+/include/ "qoriq-sata2-0.dtsi"
+ sata@220000 {
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x550>; /* SATA1LIODNR */
+ };
+/include/ "qoriq-sata2-1.dtsi"
+ sata@221000 {
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x554>; /* SATA2LIODNR */
+ };
+/include/ "qoriq-sec5.0-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/t1042si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1042si-post.dtsi
new file mode 100644
index 0000000..319b74f
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1042si-post.dtsi
@@ -0,0 +1,37 @@
+/*
+ * T1042 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "t1040si-post.dtsi"
+
+/* Place holder for ethernet related device tree nodes */
diff --git a/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi b/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
new file mode 100644
index 0000000..bbb7025
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
@@ -0,0 +1,104 @@
+/*
+ * T1040/T1042 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e5500_power_isa.dtsi"
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ pci3 = &pci3;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ sdhc = &sdhc;
+
+ crypto = &crypto;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e5500@0 {
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&mux0>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e5500@1 {
+ device_type = "cpu";
+ reg = <1>;
+ clocks = <&mux1>;
+ next-level-cache = <&L2_2>;
+ L2_2: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu2: PowerPC,e5500@2 {
+ device_type = "cpu";
+ reg = <2>;
+ clocks = <&mux2>;
+ next-level-cache = <&L2_3>;
+ L2_3: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu3: PowerPC,e5500@3 {
+ device_type = "cpu";
+ reg = <3>;
+ clocks = <&mux3>;
+ next-level-cache = <&L2_4>;
+ L2_4: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 3+ messages in thread
* RE: [linuxppc-release] [PATCH][v10] powerpc/mpc85xx:Add initial device tree support of T104x
2014-04-21 11:34 [PATCH][v10] powerpc/mpc85xx:Add initial device tree support of T104x Prabhakar Kushwaha
@ 2014-06-06 5:04 ` Shengzhou.Liu
2014-06-06 20:47 ` Scott Wood
0 siblings, 1 reply; 3+ messages in thread
From: Shengzhou.Liu @ 2014-06-06 5:04 UTC (permalink / raw)
To: prabhakar@freescale.com, linuxppc-dev@lists.ozlabs.org
Cc: Scott Wood, Priyanka Jain, Poonam.Aggrwal@freescale.com,
prabhakar@freescale.com
> -----Original Message-----
> From: linuxppc-release-bounces@linux.freescale.net [mailto:linuxppc-
> release-bounces@linux.freescale.net] On Behalf Of Prabhakar Kushwaha
> Sent: Monday, April 21, 2014 7:34 PM
> To: linuxppc-dev@lists.ozlabs.org
> Cc: Wood Scott-B07421; Jain Priyanka-B32167; Aggrwal Poonam-B10812;
> Kushwaha Prabhakar-B32579
> Subject: [linuxppc-release] [PATCH][v10] powerpc/mpc85xx:Add initial
> device tree support of T104x
>=20
> The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
> processor cores with high-performance data path acceleration architecture
> and network peripheral interfaces required for networking &
> telecommunications.
>=20
> +
> + iommu@20000 {
> + compatible =3D "fsl,pamu-v1.0", "fsl,pamu";
> + reg =3D <0x20000 0x1000>;
> + ranges =3D <0 0x20000 0x1000>;
> + #address-cells =3D <1>;
> + #size-cells =3D <1>;
> + interrupts =3D <
> + 24 2 0 0
> + 16 2 1 30>;
> + pamu0: pamu@0 {
> + reg =3D <0 0x1000>;
> + fsl,primary-cache-geometry =3D <128 1>;
> + fsl,secondary-cache-geometry =3D <16 2>;
> + };
[Shengzhou] T1040 RM says:
Hardware coherent PAMU Look-aside caches to improve performance
* A 32-entry, direct-mapped primary PAACT cache
* A 128-entry, 2-way, set-associative secondary PAACT cache
It appears it should be:=20
fsl,primary-cache-geometry =3D <32 1>;
fsl,secondary-cache-geometry =3D <128 2>;
is there any reason that it was "<128 1>, <16 2>" ?
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [linuxppc-release] [PATCH][v10] powerpc/mpc85xx:Add initial device tree support of T104x
2014-06-06 5:04 ` [linuxppc-release] " Shengzhou.Liu
@ 2014-06-06 20:47 ` Scott Wood
0 siblings, 0 replies; 3+ messages in thread
From: Scott Wood @ 2014-06-06 20:47 UTC (permalink / raw)
To: Liu Shengzhou-B36685
Cc: Aggrwal Poonam-B10812, Jain Priyanka-B32167,
linuxppc-dev@lists.ozlabs.org, Kushwaha Prabhakar-B32579
On Fri, 2014-06-06 at 00:04 -0500, Liu Shengzhou-B36685 wrote:
>
> > -----Original Message-----
> > From: linuxppc-release-bounces@linux.freescale.net [mailto:linuxppc-
> > release-bounces@linux.freescale.net] On Behalf Of Prabhakar Kushwaha
> > Sent: Monday, April 21, 2014 7:34 PM
> > To: linuxppc-dev@lists.ozlabs.org
> > Cc: Wood Scott-B07421; Jain Priyanka-B32167; Aggrwal Poonam-B10812;
> > Kushwaha Prabhakar-B32579
> > Subject: [linuxppc-release] [PATCH][v10] powerpc/mpc85xx:Add initial
> > device tree support of T104x
> >
> > The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
> > processor cores with high-performance data path acceleration architecture
> > and network peripheral interfaces required for networking &
> > telecommunications.
> >
> > +
> > + iommu@20000 {
> > + compatible = "fsl,pamu-v1.0", "fsl,pamu";
> > + reg = <0x20000 0x1000>;
> > + ranges = <0 0x20000 0x1000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + interrupts = <
> > + 24 2 0 0
> > + 16 2 1 30>;
> > + pamu0: pamu@0 {
> > + reg = <0 0x1000>;
> > + fsl,primary-cache-geometry = <128 1>;
> > + fsl,secondary-cache-geometry = <16 2>;
> > + };
>
>
> [Shengzhou] T1040 RM says:
> Hardware coherent PAMU Look-aside caches to improve performance
> * A 32-entry, direct-mapped primary PAACT cache
> * A 128-entry, 2-way, set-associative secondary PAACT cache
> It appears it should be:
> fsl,primary-cache-geometry = <32 1>;
> fsl,secondary-cache-geometry = <128 2>;
>
> is there any reason that it was "<128 1>, <16 2>" ?
The B4 device trees are also suspicous.
-Scott
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2014-06-06 20:47 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-04-21 11:34 [PATCH][v10] powerpc/mpc85xx:Add initial device tree support of T104x Prabhakar Kushwaha
2014-06-06 5:04 ` [linuxppc-release] " Shengzhou.Liu
2014-06-06 20:47 ` Scott Wood
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).