* [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC
@ 2015-01-29 7:52 Shengzhou Liu
0 siblings, 0 replies; 7+ messages in thread
From: Shengzhou Liu @ 2015-01-29 7:52 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
arch/powerpc/boot/dts/fsl/t1023si-post.dtsi | 351 ++++++++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/t1024si-post.dtsi | 50 ++++
arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi | 88 +++++++
3 files changed, 489 insertions(+)
create mode 100644 arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
new file mode 100644
index 0000000..23fbc5d
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
@@ -0,0 +1,351 @@
+/*
+ * T1023 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc", "simple-bus";
+ interrupts = <25 2 0 0>;
+};
+
+&pci0 {
+ compatible = "fsl,t1024-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <20 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <20 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+&pci1 {
+ compatible = "fsl,t1024-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ interrupts = <21 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <21 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+&pci2 {
+ compatible = "fsl,t1024-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <22 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <22 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,t1024-dcsr-epu", "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,t1024-dcsr-cnpc", "fsl,dcsr-cnpc";
+ reg = <0x1000 0x1000 0x1002000 0x10000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0x1A000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,t1024-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,t1024-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,t1024-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-snpc@30000 {
+ compatible = "fsl,t1024-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x30000 0x1000 0x1022000 0x10000>;
+ };
+ dcsr-snpc@31000 {
+ compatible = "fsl,t1024-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x31000 0x1000 0x1042000 0x10000>;
+ };
+ dcsr-cpu-sb-proxy@100000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x100000 0x1000 0x101000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@108000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x108000 0x1000 0x109000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <16>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v5.0",
+ "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,t1024-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000>;
+ interrupts = <16 2 1 27>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet2-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x1000>;
+ ranges = <0 0x20000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ pamu0: pamu@0 {
+ reg = <0 0x1000>;
+ fsl,primary-cache-geometry = <128 1>;
+ fsl,secondary-cache-geometry = <16 2>;
+ };
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,t1024-device-config", "fsl,qoriq-device-config-2.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ fsl,liodn-bits = <12>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,t1024-clockgen", "fsl,qoriq-clockgen-2.0",
+ "fixed-clock";
+ reg = <0xe1000 0x1000>;
+ clock-output-names = "sysclk";
+ #clock-cells = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pll0: pll0@800 {
+ #clock-cells = <1>;
+ reg = <0x800 4>;
+ compatible = "fsl,core-pll-clock";
+ clocks = <&clockgen>;
+ clock-output-names = "pll0", "pll0-div2";
+ };
+ mux0: mux0@0 {
+ #clock-cells = <0>;
+ reg = <0x0 4>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>;
+ clock-names = "pll0_0", "pll0_1";
+ clock-output-names = "cmux0";
+ };
+ mux1: mux1@20 {
+ #clock-cells = <0>;
+ reg = <0x20 4>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>;
+ clock-names = "pll0_0", "pll0_1";
+ clock-output-names = "cmux1";
+ };
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,t1024-rcpm", "fsl,qoriq-rcpm-2.0";
+ reg = <0xe2000 0x1000>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,t1024-sfp";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,t1024-serdes";
+ reg = <0xea000 0x4000>;
+ };
+
+ scfg: global-utilities@fc000 {
+ compatible = "fsl,t1024-scfg";
+ reg = <0xfc000 0x1000>;
+ };
+
+/include/ "elo3-dma-0.dtsi"
+/include/ "elo3-dma-1.dtsi"
+
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ compatible = "fsl,t1024-esdhc", "fsl,esdhc";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x530>; /* eSDHCLIODNR */
+ sdhci,auto-cmd12;
+ no-1-8-v;
+ sleep = <&rcpm 0x00000080>;
+ };
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+ gpio@130000 {
+ sleep = <&rcpm 0x00000040>;
+ };
+/include/ "qoriq-gpio-1.dtsi"
+/include/ "qoriq-gpio-2.dtsi"
+/include/ "qoriq-gpio-3.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ compatible = "fsl-usb2-mph-v2.5", "fsl-usb2-mph";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x520>; /* USB1LIODNR */
+ phy_type = "utmi";
+ sleep = <&rcpm 0x00000020>;
+ port0;
+ };
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ compatible = "fsl-usb2-dr-v2.5", "fsl-usb2-dr";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x524>; /* USB2LIODNR */
+ dr_mode = "host";
+ phy_type = "utmi";
+ sleep = <&rcpm 0x00000010>;
+ };
+/include/ "qoriq-sata2-0.dtsi"
+sata@220000 {
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x550>; /* SATA1LIODNR */
+};
+
+/include/ "qoriq-sec5.0-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
new file mode 100644
index 0000000..cdc570d
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
@@ -0,0 +1,50 @@
+/*
+ * T1024 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "t1023si-post.dtsi"
+
+/ {
+ aliases {
+ vga = &display;
+ display = &display;
+ };
+};
+
+&soc {
+ display:display@180000 {
+ compatible = "fsl,t1024-diu", "fsl,diu";
+ reg = <0x180000 1000>;
+ interrupts = <74 2 0 0>;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi b/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
new file mode 100644
index 0000000..7e513b7
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
@@ -0,0 +1,88 @@
+/*
+ * T1024/T1023 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e5500_power_isa.dtsi"
+
+/ {
+ compatible = "fsl,T104x";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ dma0 = &dma0;
+ dma1 = &dma1;
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ sdhc = &sdhc;
+
+ crypto = &crypto;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e5500@0 {
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&mux0>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e5500@1 {
+ device_type = "cpu";
+ reg = <1>;
+ clocks = <&mux1>;
+ next-level-cache = <&L2_2>;
+ L2_2: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+};
--
1.8.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC
@ 2015-04-03 10:35 Shengzhou Liu
2015-04-03 10:35 ` [PATCH 2/4] powerpc/fsl-booke: Add T1024 QDS board support Shengzhou Liu
` (3 more replies)
0 siblings, 4 replies; 7+ messages in thread
From: Shengzhou Liu @ 2015-04-03 10:35 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
arch/powerpc/boot/dts/fsl/t1023si-post.dtsi | 349 ++++++++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/t1024si-post.dtsi | 97 ++++++++
arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi | 87 +++++++
3 files changed, 533 insertions(+)
create mode 100644 arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
new file mode 100644
index 0000000..5db23a7
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
@@ -0,0 +1,349 @@
+/*
+ * T1023 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc", "simple-bus";
+ interrupts = <25 2 0 0>;
+};
+
+&pci0 {
+ compatible = "fsl,t1023-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <20 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <20 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+&pci1 {
+ compatible = "fsl,t1023-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ interrupts = <21 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <21 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+&pci2 {
+ compatible = "fsl,t1023-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <22 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <22 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,t1023-dcsr-epu", "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,t1023-dcsr-cnpc", "fsl,dcsr-cnpc";
+ reg = <0x1000 0x1000 0x1002000 0x10000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0x1A000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,t1023-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,t1023-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,t1023-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-snpc@30000 {
+ compatible = "fsl,t1023-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x30000 0x1000 0x1022000 0x10000>;
+ };
+ dcsr-snpc@31000 {
+ compatible = "fsl,t1023-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x31000 0x1000 0x1042000 0x10000>;
+ };
+ dcsr-cpu-sb-proxy@100000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x100000 0x1000 0x101000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@108000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x108000 0x1000 0x109000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <16>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v5.0",
+ "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,t1023-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000>;
+ interrupts = <16 2 1 27>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet2-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x1000>;
+ ranges = <0 0x20000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ pamu0: pamu@0 {
+ reg = <0 0x1000>;
+ fsl,primary-cache-geometry = <128 1>;
+ fsl,secondary-cache-geometry = <32 2>;
+ };
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,t1023-device-config", "fsl,qoriq-device-config-2.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ fsl,liodn-bits = <12>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,t1023-clockgen", "fsl,qoriq-clockgen-2.0",
+ "fixed-clock";
+ reg = <0xe1000 0x1000>;
+ clock-output-names = "sysclk";
+ #clock-cells = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pll0: pll0@800 {
+ #clock-cells = <1>;
+ reg = <0x800 4>;
+ compatible = "fsl,core-pll-clock";
+ clocks = <&clockgen>;
+ clock-output-names = "pll0", "pll0-div2";
+ };
+ mux0: mux0@0 {
+ #clock-cells = <0>;
+ reg = <0x0 4>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>;
+ clock-names = "pll0_0", "pll0_1";
+ clock-output-names = "cmux0";
+ };
+ mux1: mux1@20 {
+ #clock-cells = <0>;
+ reg = <0x20 4>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>;
+ clock-names = "pll0_0", "pll0_1";
+ clock-output-names = "cmux1";
+ };
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,t1023-rcpm", "fsl,qoriq-rcpm-2.0";
+ reg = <0xe2000 0x1000>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,t1023-sfp";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,t1023-serdes";
+ reg = <0xea000 0x4000>;
+ };
+
+ scfg: global-utilities@fc000 {
+ compatible = "fsl,t1023-scfg";
+ reg = <0xfc000 0x1000>;
+ };
+
+/include/ "elo3-dma-0.dtsi"
+/include/ "elo3-dma-1.dtsi"
+
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ compatible = "fsl,t1023-esdhc", "fsl,esdhc";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x530>; /* eSDHCLIODNR */
+ sdhci,auto-cmd12;
+ no-1-8-v;
+ sleep = <&rcpm 0x00000080>;
+ };
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+ gpio@130000 {
+ sleep = <&rcpm 0x00000040>;
+ };
+/include/ "qoriq-gpio-1.dtsi"
+/include/ "qoriq-gpio-2.dtsi"
+/include/ "qoriq-gpio-3.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ compatible = "fsl-usb2-mph-v2.5", "fsl-usb2-mph";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x520>; /* USB1LIODNR */
+ phy_type = "utmi";
+ sleep = <&rcpm 0x00000020>;
+ port0;
+ };
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ compatible = "fsl-usb2-dr-v2.5", "fsl-usb2-dr";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x524>; /* USB2LIODNR */
+ dr_mode = "host";
+ phy_type = "utmi";
+ sleep = <&rcpm 0x00000010>;
+ };
+/include/ "qoriq-sata2-0.dtsi"
+sata@220000 {
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x550>; /* SATA1LIODNR */
+};
+
+/include/ "qoriq-sec5.0-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
new file mode 100644
index 0000000..13948bb
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
@@ -0,0 +1,97 @@
+/*
+ * T1024 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "t1023si-post.dtsi"
+
+/ {
+ aliases {
+ vga = &display;
+ display = &display;
+ };
+};
+
+&soc {
+/include/ "qoriq-tdm1.0.dtsi"
+
+ display:display@180000 {
+ compatible = "fsl,t1024-diu", "fsl,diu";
+ reg = <0x180000 1000>;
+ interrupts = <74 2 0 0>;
+ };
+};
+
+&qe {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "qe";
+ compatible = "fsl,qe";
+ fsl,qe-num-riscs = <1>;
+ fsl,qe-num-snums = <28>;
+
+ qeic: interrupt-controller@80 {
+ interrupt-controller;
+ compatible = "fsl,qe-ic";
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ reg = <0x80 0x80>;
+ interrupts = <95 2 0 0 94 2 0 0>; //high:79 low:78
+ };
+
+ ucc@2000 {
+ cell-index = <1>;
+ reg = <0x2000 0x200>;
+ interrupts = <32>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@2200 {
+ cell-index = <3>;
+ reg = <0x2200 0x200>;
+ interrupts = <34>;
+ interrupt-parent = <&qeic>;
+ };
+
+ muram@10000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0x0 0x10000 0x6000>;
+
+ data-only@0 {
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0x0 0x6000>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi b/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
new file mode 100644
index 0000000..1f1a9f8
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
@@ -0,0 +1,87 @@
+/*
+ * T1024/T1023 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e5500_power_isa.dtsi"
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ dma0 = &dma0;
+ dma1 = &dma1;
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ sdhc = &sdhc;
+
+ crypto = &crypto;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e5500@0 {
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&mux0>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e5500@1 {
+ device_type = "cpu";
+ reg = <1>;
+ clocks = <&mux1>;
+ next-level-cache = <&L2_2>;
+ L2_2: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+};
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/4] powerpc/fsl-booke: Add T1024 QDS board support
2015-04-03 10:35 [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC Shengzhou Liu
@ 2015-04-03 10:35 ` Shengzhou Liu
2015-04-03 10:35 ` [PATCH 3/4] powerpc/fsl-booke: Add T1024 RDB " Shengzhou Liu
` (2 subsequent siblings)
3 siblings, 0 replies; 7+ messages in thread
From: Shengzhou Liu @ 2015-04-03 10:35 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
Add support for Freescale T1024/T1023 QorIQ Development System Board.
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10G Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep sleep power management implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A and one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
arch/powerpc/boot/dts/t1024qds.dts | 89 ++++++++++
arch/powerpc/boot/dts/t102xqds.dtsi | 247 ++++++++++++++++++++++++++
arch/powerpc/platforms/85xx/Kconfig | 2 +-
arch/powerpc/platforms/85xx/corenet_generic.c | 1 +
4 files changed, 338 insertions(+), 1 deletion(-)
create mode 100644 arch/powerpc/boot/dts/t1024qds.dts
create mode 100644 arch/powerpc/boot/dts/t102xqds.dtsi
diff --git a/arch/powerpc/boot/dts/t1024qds.dts b/arch/powerpc/boot/dts/t1024qds.dts
new file mode 100644
index 0000000..35e0d34
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1024qds.dts
@@ -0,0 +1,89 @@
+/*
+ * T1024 QDS Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+/include/ "t102xqds.dtsi"
+
+/ {
+ model = "fsl,T1024QDS";
+ compatible = "fsl,T1024QDS";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ qe: qe@ffe140000 {
+ ranges = <0x0 0xf 0xfe140000 0x40000>;
+ reg = <0xf 0xfe140000 0 0x480>;
+ brg-frequency = <0>;
+ bus-frequency = <0>;
+
+ si1: si@700 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,qe-si";
+ reg = <0x700 0x80>;
+ };
+
+ siram1: siram@1000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-siram";
+ reg = <0x1000 0x800>;
+ };
+
+ tdma: ucc@2000 {
+ compatible = "fsl,ucc-tdm";
+ rx-clock-name = "clk8";
+ tx-clock-name = "clk9";
+ fsl,rx-sync-clock = "rsync_pin";
+ fsl,tx-sync-clock = "tsync_pin";
+ fsl,tx-timeslot = <0xfffffffe>;
+ fsl,rx-timeslot = <0xfffffffe>;
+ fsl,tdm-framer-type = "e1";
+ fsl,tdm-mode = "normal";
+ fsl,tdm-id = <0>;
+ fsl,siram-entry-id = <0>;
+ };
+
+ serial: ucc@2200 {
+ device_type = "serial";
+ compatible = "ucc_uart";
+ port-number = <1>;
+ rx-clock-name = "brg2";
+ tx-clock-name = "brg2";
+ };
+ };
+};
+
+/include/ "fsl/t1024si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/t102xqds.dtsi b/arch/powerpc/boot/dts/t102xqds.dtsi
new file mode 100644
index 0000000..58e401c
--- /dev/null
+++ b/arch/powerpc/boot/dts/t102xqds.dtsi
@@ -0,0 +1,247 @@
+/*
+ * T102x QDS Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/ {
+ model = "fsl,T1024QDS";
+ compatible = "fsl,T1024QDS";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ ifc: localbus@ffe124000 {
+ reg = <0xf 0xfe124000 0 0x2000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000
+ 2 0 0xf 0xff800000 0x00010000
+ 3 0 0xf 0xffdf0000 0x00008000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+ };
+
+ board-control@3,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,tetra-fpga", "fsl,fpga-qixis";
+ reg = <3 0 0x300>;
+ ranges = <0 3 0 0x300>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ dcsr: dcsr@f00000000 {
+ ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+ };
+
+ soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+ spi@110000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q128a11"; /* 16MB */
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ };
+
+ flash@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25wf040"; /* 512KB */
+ reg = <1>;
+ spi-max-frequency = <10000000>;
+ };
+
+ flash@2 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "eon,en25s64"; /* 8MB */
+ reg = <2>;
+ spi-max-frequency = <10000000>;
+ };
+
+ slic@2 {
+ compatible = "maxim,ds26522";
+ reg = <2>;
+ spi-max-frequency = <2000000>;
+ };
+
+ slic@3 {
+ compatible = "maxim,ds26522";
+ reg = <3>;
+ spi-max-frequency = <2000000>;
+ };
+ };
+
+ i2c@118000 {
+ pca9547@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+
+ eeprom@50 {
+ compatible = "at24,24c512";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "at24,24c02";
+ reg = <0x51>;
+ };
+
+ eeprom@57 {
+ compatible = "at24,24c02";
+ reg = <0x57>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ ina220@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <1000>;
+ };
+
+ ina220@41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ adt7461@4c {
+ /* Thermal Monitor */
+ compatible = "adi,adt7461";
+ reg = <0x4c>;
+ };
+
+ eeprom@55 {
+ compatible = "at24,24c02";
+ reg = <0x55>;
+ };
+
+ eeprom@56 {
+ compatible = "at24,24c512";
+ reg = <0x56>;
+ };
+
+ eeprom@57 {
+ compatible = "at24,24c512";
+ reg = <0x57>;
+ };
+ };
+ };
+ rtc@68 {
+ compatible = "dallas,ds3232";
+ reg = <0x68>;
+ interrupts = <0x5 0x1 0 0>;
+ };
+ };
+ };
+
+ pci0: pcie@ffe240000 {
+ reg = <0xf 0xfe240000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie@ffe250000 {
+ reg = <0xf 0xfe250000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie@ffe260000 {
+ reg = <0xf 0xfe260000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 2fb4b24..e628d40 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -282,7 +282,7 @@ config CORENET_GENERIC
For 64bit kernel, the following boards are supported:
T208x QDS/RDB, T4240 QDS/RDB and B4 QDS
The following boards are supported for both 32bit and 64bit kernel:
- P5020 DS, P5040 DS and T104xQDS/RDB
+ P5020 DS, P5040 DS, T102x QDS, T104x QDS/RDB
endif # FSL_SOC_BOOKE
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index 9824d2c..f61f477 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -150,6 +150,7 @@ static const char * const boards[] __initconst = {
"fsl,B4860QDS",
"fsl,B4420QDS",
"fsl,B4220QDS",
+ "fsl,T1024QDS",
"fsl,T1040QDS",
"fsl,T1042QDS",
"fsl,T1040RDB",
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 3/4] powerpc/fsl-booke: Add T1024 RDB board support
2015-04-03 10:35 [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC Shengzhou Liu
2015-04-03 10:35 ` [PATCH 2/4] powerpc/fsl-booke: Add T1024 QDS board support Shengzhou Liu
@ 2015-04-03 10:35 ` Shengzhou Liu
2015-04-07 23:45 ` Scott Wood
2015-04-03 10:35 ` [PATCH 4/4] powerpc/fsl-booke: Add T1023 " Shengzhou Liu
2015-04-07 23:49 ` [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC Scott Wood
3 siblings, 1 reply; 7+ messages in thread
From: Shengzhou Liu @ 2015-04-03 10:35 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- Processor: T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- DDR: 64-bit 4GB DDR3L UDIMM with ECC and interleaving support
- Ethernet: two 10M/100M/1Gbps RGMII ports and one 10Gbps Base-T port on-board
- Accelerator: DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 1GB NAND Flash and CPLD system controlling
- PCIe: one PCIe slot and two Mini-PCIe connectors on-board
- USB: two Type-A USB2.0 ports with internal PHY
- eSDHC: one SDHC/MMC/eMMC connector
- eSPI: one 64MB N25Q512 SPI flash
- QE-TDM: support TDM Riser card
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- I2C: four I2C controllers
- UART: two UART on board
- Deep sleep power management support
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
arch/powerpc/boot/dts/t1024rdb.dts | 235 ++++++++++++++++++++++++++
arch/powerpc/platforms/85xx/Kconfig | 2 +-
arch/powerpc/platforms/85xx/corenet_generic.c | 1 +
3 files changed, 237 insertions(+), 1 deletion(-)
create mode 100644 arch/powerpc/boot/dts/t1024rdb.dts
diff --git a/arch/powerpc/boot/dts/t1024rdb.dts b/arch/powerpc/boot/dts/t1024rdb.dts
new file mode 100644
index 0000000..4c85599
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1024rdb.dts
@@ -0,0 +1,235 @@
+/*
+ * T1024 RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+
+/ {
+ model = "fsl,T1024RDB";
+ compatible = "fsl,T1024RDB";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ ifc: localbus@ffe124000 {
+ reg = <0xf 0xfe124000 0 0x2000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000
+ 2 0 0xf 0xff800000 0x00010000
+ 3 0 0xf 0xffdf0000 0x00008000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+ };
+
+ board-control@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,t1024-cpld", "fsl,deepsleep-cpld";
+ reg = <3 0 0x300>;
+ ranges = <0 3 0 0x300>;
+ bank-width = <1>;
+ device-width = <1>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ dcsr: dcsr@f00000000 {
+ ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+ };
+
+ soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+ spi@110000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q512ax3";
+ reg = <0>;
+ spi-max-frequency = <10000000>; /* input clk */
+ };
+
+ slic@1 {
+ compatible = "maxim,ds26522";
+ reg = <1>;
+ spi-max-frequency = <2000000>;
+ };
+
+ slic@2 {
+ compatible = "maxim,ds26522";
+ reg = <2>;
+ spi-max-frequency = <2000000>;
+ };
+ };
+
+ i2c@118000 {
+ adt7461@4c {
+ /* Thermal Monitor */
+ compatible = "adi,adt7461";
+ reg = <0x4c>;
+ };
+
+ eeprom@50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ interrupts = <0x1 0x1 0 0>;
+ };
+ };
+
+ i2c@118100 {
+ pca9546@77 {
+ compatible = "nxp,pca9546";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+
+ qe: qe@ffe139999 {
+ ranges = <0x0 0xf 0xfe140000 0x40000>;
+ reg = <0xf 0xfe140000 0 0x480>;
+ brg-frequency = <0>;
+ bus-frequency = <0>;
+
+ si1: si@700 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,qe-si";
+ reg = <0x700 0x80>;
+ };
+
+ siram1: siram@1000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-siram";
+ reg = <0x1000 0x800>;
+ };
+
+ tdma: ucc@2000 {
+ compatible = "fsl,ucc-tdm";
+ rx-clock-name = "clk8";
+ tx-clock-name = "clk9";
+ fsl,rx-sync-clock = "rsync_pin";
+ fsl,tx-sync-clock = "tsync_pin";
+ fsl,tx-timeslot = <0xfffffffe>;
+ fsl,rx-timeslot = <0xfffffffe>;
+ fsl,tdm-framer-type = "e1";
+ fsl,tdm-mode = "normal";
+ fsl,tdm-id = <0>;
+ fsl,siram-entry-id = <0>;
+ };
+
+ ucc@2200 {
+ compatible = "fsl,ucc_hdlc";
+ rx-clock-name = "brg2";
+ tx-clock-name = "brg2";
+ fsl,rx-sync-clock = "none";
+ fsl,tx-sync-clock = "none";
+ fsl,tx-timeslot = <0xfffffffe>;
+ fsl,rx-timeslot = <0xfffffffe>;
+ fsl,tdm-framer-type = "e1";
+ fsl,tdm-mode = "normal";
+ fsl,tdm-id = <1>;
+ fsl,siram-entry-id = <2>;
+ fsl,inter-loopback;
+ };
+ };
+
+ pci0: pcie@ffe240000 {
+ reg = <0xf 0xfe240000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie@ffe250000 {
+ reg = <0xf 0xfe250000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie@ffe260000 {
+ reg = <0xf 0xfe260000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};
+
+/include/ "fsl/t1024si-post.dtsi"
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index e628d40..97915fe 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -282,7 +282,7 @@ config CORENET_GENERIC
For 64bit kernel, the following boards are supported:
T208x QDS/RDB, T4240 QDS/RDB and B4 QDS
The following boards are supported for both 32bit and 64bit kernel:
- P5020 DS, P5040 DS, T102x QDS, T104x QDS/RDB
+ P5020 DS, P5040 DS, T102x QDS/RDB, T104x QDS/RDB
endif # FSL_SOC_BOOKE
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index f61f477..d7c1b4d 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -151,6 +151,7 @@ static const char * const boards[] __initconst = {
"fsl,B4420QDS",
"fsl,B4220QDS",
"fsl,T1024QDS",
+ "fsl,T1024RDB",
"fsl,T1040QDS",
"fsl,T1042QDS",
"fsl,T1040RDB",
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 4/4] powerpc/fsl-booke: Add T1023 RDB board support
2015-04-03 10:35 [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC Shengzhou Liu
2015-04-03 10:35 ` [PATCH 2/4] powerpc/fsl-booke: Add T1024 QDS board support Shengzhou Liu
2015-04-03 10:35 ` [PATCH 3/4] powerpc/fsl-booke: Add T1024 RDB " Shengzhou Liu
@ 2015-04-03 10:35 ` Shengzhou Liu
2015-04-07 23:49 ` [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC Scott Wood
3 siblings, 0 replies; 7+ messages in thread
From: Shengzhou Liu @ 2015-04-03 10:35 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: Shengzhou Liu
T1023RDB is a Freescale Reference Design Board that hosts T1023 SoC.
T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- one 1G RGMII port on-board(RTL8211F PHY)
- one 1G SGMII port on-board(RTL8211F PHY)
- one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC flash on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
arch/powerpc/boot/dts/t1023rdb.dts | 151 ++++++++++++++++++++++++++
arch/powerpc/platforms/85xx/corenet_generic.c | 1 +
2 files changed, 152 insertions(+)
create mode 100644 arch/powerpc/boot/dts/t1023rdb.dts
diff --git a/arch/powerpc/boot/dts/t1023rdb.dts b/arch/powerpc/boot/dts/t1023rdb.dts
new file mode 100644
index 0000000..3780e68
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1023rdb.dts
@@ -0,0 +1,151 @@
+/*
+ * T1023 RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+
+/ {
+ model = "fsl,T1023RDB";
+ compatible = "fsl,T1023RDB";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ ifc: localbus@ffe124000 {
+ reg = <0xf 0xfe124000 0 0x2000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000
+ 1 0 0xf 0xff800000 0x00010000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ dcsr: dcsr@f00000000 {
+ ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+ };
+
+ soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+ spi@110000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25fl512s";
+ reg = <0>;
+ spi-max-frequency = <10000000>; /* input clk */
+ };
+ };
+
+ i2c@118000 {
+ eeprom@50 {
+ compatible = "stm,m24256";
+ reg = <0x50>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ interrupts = <0x5 0x1 0 0>;
+ };
+ };
+
+ i2c@118100 {
+ };
+ };
+
+ pci0: pcie@ffe240000 {
+ reg = <0xf 0xfe240000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie@ffe250000 {
+ reg = <0xf 0xfe250000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie@ffe260000 {
+ reg = <0xf 0xfe260000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};
+
+/include/ "fsl/t1023si-post.dtsi"
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index d7c1b4d..bd839dc 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -150,6 +150,7 @@ static const char * const boards[] __initconst = {
"fsl,B4860QDS",
"fsl,B4420QDS",
"fsl,B4220QDS",
+ "fsl,T1023RDB",
"fsl,T1024QDS",
"fsl,T1024RDB",
"fsl,T1040QDS",
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH 3/4] powerpc/fsl-booke: Add T1024 RDB board support
2015-04-03 10:35 ` [PATCH 3/4] powerpc/fsl-booke: Add T1024 RDB " Shengzhou Liu
@ 2015-04-07 23:45 ` Scott Wood
0 siblings, 0 replies; 7+ messages in thread
From: Scott Wood @ 2015-04-07 23:45 UTC (permalink / raw)
To: Shengzhou Liu; +Cc: linuxppc-dev
On Fri, 2015-04-03 at 18:35 +0800, Shengzhou Liu wrote:
> + board-control@2,0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "fsl,t1024-cpld", "fsl,deepsleep-cpld";
No "fsl,deepsleep-cpld". Just have the driver recognize the compatibles
for the chips that have deep sleep.
Even if you were to do this, it would need to be documented in a
binding, and you'd need to be more specific about what CPLD family
you're talking about.
> + tdma: ucc@2000 {
> + compatible = "fsl,ucc-tdm";
> + rx-clock-name = "clk8";
> + tx-clock-name = "clk9";
> + fsl,rx-sync-clock = "rsync_pin";
> + fsl,tx-sync-clock = "tsync_pin";
> + fsl,tx-timeslot = <0xfffffffe>;
> + fsl,rx-timeslot = <0xfffffffe>;
> + fsl,tdm-framer-type = "e1";
> + fsl,tdm-mode = "normal";
> + fsl,tdm-id = <0>;
> + fsl,siram-entry-id = <0>;
> + };
Binding?
-Scott
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC
2015-04-03 10:35 [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC Shengzhou Liu
` (2 preceding siblings ...)
2015-04-03 10:35 ` [PATCH 4/4] powerpc/fsl-booke: Add T1023 " Shengzhou Liu
@ 2015-04-07 23:49 ` Scott Wood
3 siblings, 0 replies; 7+ messages in thread
From: Scott Wood @ 2015-04-07 23:49 UTC (permalink / raw)
To: Shengzhou Liu; +Cc: linuxppc-dev
On Fri, 2015-04-03 at 18:35 +0800, Shengzhou Liu wrote:
> + rcpm: global-utilities@e2000 {
> + compatible = "fsl,t1023-rcpm", "fsl,qoriq-rcpm-2.0";
> + reg = <0xe2000 0x1000>;
> + };
> +
> + sfp: sfp@e8000 {
> + compatible = "fsl,t1023-sfp";
> + reg = <0xe8000 0x1000>;
> + };
> +
> + serdes: serdes@ea000 {
> + compatible = "fsl,t1023-serdes";
> + reg = <0xea000 0x4000>;
> + };
Consistent whitespace please. Just one space after "reg".
> +/include/ "qoriq-esdhc-0.dtsi"
> + sdhc@114000 {
> + compatible = "fsl,t1023-esdhc", "fsl,esdhc";
> + fsl,iommu-parent = <&pamu0>;
> + fsl,liodn-reg = <&guts 0x530>; /* eSDHCLIODNR */
> + sdhci,auto-cmd12;
> + no-1-8-v;
> + sleep = <&rcpm 0x00000080>;
Get rid of "sleep" -- it's undocumented copy-and-paste from something
that was never finished.
-Scott
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2015-04-07 23:49 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-04-03 10:35 [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC Shengzhou Liu
2015-04-03 10:35 ` [PATCH 2/4] powerpc/fsl-booke: Add T1024 QDS board support Shengzhou Liu
2015-04-03 10:35 ` [PATCH 3/4] powerpc/fsl-booke: Add T1024 RDB " Shengzhou Liu
2015-04-07 23:45 ` Scott Wood
2015-04-03 10:35 ` [PATCH 4/4] powerpc/fsl-booke: Add T1023 " Shengzhou Liu
2015-04-07 23:49 ` [PATCH 1/4] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC Scott Wood
-- strict thread matches above, loose matches on Subject: below --
2015-01-29 7:52 Shengzhou Liu
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).