From: Shengzhou Liu <Shengzhou.Liu@freescale.com>
To: <linuxppc-dev@lists.ozlabs.org>, <scottwood@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Subject: [PATCH 4/4 v3] powerpc/fsl-booke: Add T1023 RDB board support
Date: Thu, 9 Apr 2015 16:07:45 +0800 [thread overview]
Message-ID: <1428566865-35732-4-git-send-email-Shengzhou.Liu@freescale.com> (raw)
In-Reply-To: <1428566865-35732-1-git-send-email-Shengzhou.Liu@freescale.com>
T1023RDB is a Freescale Reference Design Board that hosts T1023 SoC.
T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- one 1G RGMII port on-board(RTL8211F PHY)
- one 1G SGMII port on-board(RTL8211F PHY)
- one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC flash on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v3: no change
v2: no change
arch/powerpc/boot/dts/t1023rdb.dts | 151 ++++++++++++++++++++++++++
arch/powerpc/platforms/85xx/corenet_generic.c | 1 +
2 files changed, 152 insertions(+)
create mode 100644 arch/powerpc/boot/dts/t1023rdb.dts
diff --git a/arch/powerpc/boot/dts/t1023rdb.dts b/arch/powerpc/boot/dts/t1023rdb.dts
new file mode 100644
index 0000000..3780e68
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1023rdb.dts
@@ -0,0 +1,151 @@
+/*
+ * T1023 RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+
+/ {
+ model = "fsl,T1023RDB";
+ compatible = "fsl,T1023RDB";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ ifc: localbus@ffe124000 {
+ reg = <0xf 0xfe124000 0 0x2000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000
+ 1 0 0xf 0xff800000 0x00010000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x2 0x0 0x10000>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ dcsr: dcsr@f00000000 {
+ ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+ };
+
+ soc: soc@ffe000000 {
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+ spi@110000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25fl512s";
+ reg = <0>;
+ spi-max-frequency = <10000000>; /* input clk */
+ };
+ };
+
+ i2c@118000 {
+ eeprom@50 {
+ compatible = "stm,m24256";
+ reg = <0x50>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ interrupts = <0x5 0x1 0 0>;
+ };
+ };
+
+ i2c@118100 {
+ };
+ };
+
+ pci0: pcie@ffe240000 {
+ reg = <0xf 0xfe240000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie@ffe250000 {
+ reg = <0xf 0xfe250000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie@ffe260000 {
+ reg = <0xf 0xfe260000 0 0x10000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x10000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};
+
+/include/ "fsl/t1023si-post.dtsi"
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index d7c1b4d..bd839dc 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -150,6 +150,7 @@ static const char * const boards[] __initconst = {
"fsl,B4860QDS",
"fsl,B4420QDS",
"fsl,B4220QDS",
+ "fsl,T1023RDB",
"fsl,T1024QDS",
"fsl,T1024RDB",
"fsl,T1040QDS",
--
2.1.0.27.g96db324
next prev parent reply other threads:[~2015-04-09 8:11 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-04-09 8:07 [PATCH 1/4 v3] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC Shengzhou Liu
2015-04-09 8:07 ` [PATCH 2/4 v3] powerpc/fsl-booke: Add T1024 QDS board support Shengzhou Liu
2015-05-29 0:24 ` [2/4,v3] " Scott Wood
2015-06-01 8:23 ` Liu Shengzhou
2015-06-01 22:00 ` Scott Wood
2015-04-09 8:07 ` [PATCH 3/4 v3] powerpc/fsl-booke: Add T1024 RDB " Shengzhou Liu
2015-04-09 8:07 ` Shengzhou Liu [this message]
2015-05-29 0:30 ` [4/4,v3] powerpc/fsl-booke: Add T1023 " Scott Wood
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1428566865-35732-4-git-send-email-Shengzhou.Liu@freescale.com \
--to=shengzhou.liu@freescale.com \
--cc=linuxppc-dev@lists.ozlabs.org \
--cc=scottwood@freescale.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).