[PATCH 1/4 v3] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC

[PATCH 1/4 v3] powerpc/fsl-booke: Add device tree support for T1024/T1023 SoC

[Shengzhou Liu]

The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
  - Three PCI Express 2.0 controllers
- Additional peripheral interfaces
  - One SATA 2.0 controller
  - Two USB 2.0 controllers with integrated PHY
  - Enhanced secure digital host controller (SD/eSDHC/eMMC)
  - Enhanced serial peripheral interface (eSPI)
  - Four I2C controllers
  - Four 2-pin UARTs or two 4-pin UARTs
  - Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v3: use qoriq-clockgen2.dtsi
v2: Integrated scott's comments.
note: qoriq-tdm1.0.dtsi depends on patch http://patchwork.ozlabs.org/patch/457605/

 arch/powerpc/boot/dts/fsl/t1023si-post.dtsi | 330 ++++++++++++++++++++++++++++
 arch/powerpc/boot/dts/fsl/t1024si-post.dtsi | 102 +++++++++
 arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi  |  87 ++++++++
 3 files changed, 519 insertions(+)
 create mode 100644 arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
 create mode 100644 arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
 create mode 100644 arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi

diff --git a/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
new file mode 100644
index 0000000..dbe6578
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1023si-post.dtsi
@@ -0,0 +1,330 @@
+/*
+ * T1023 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,ifc", "simple-bus";
+	interrupts = <25 2 0 0>;
+};
+
+&pci0 {
+	compatible = "fsl,t1023-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	interrupts = <20 2 0 0>;
+	fsl,iommu-parent = <&pamu0>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <20 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 40 1 0 0
+			0000 0 0 2 &mpic 1 1 0 0
+			0000 0 0 3 &mpic 2 1 0 0
+			0000 0 0 4 &mpic 3 1 0 0
+			>;
+	};
+};
+
+&pci1 {
+	compatible = "fsl,t1023-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 0xff>;
+	interrupts = <21 2 0 0>;
+	fsl,iommu-parent = <&pamu0>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <21 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 41 1 0 0
+			0000 0 0 2 &mpic 5 1 0 0
+			0000 0 0 3 &mpic 6 1 0 0
+			0000 0 0 4 &mpic 7 1 0 0
+			>;
+	};
+};
+
+&pci2 {
+	compatible = "fsl,t1023-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	interrupts = <22 2 0 0>;
+	fsl,iommu-parent = <&pamu0>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <22 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 42 1 0 0
+			0000 0 0 2 &mpic 9 1 0 0
+			0000 0 0 3 &mpic 10 1 0 0
+			0000 0 0 4 &mpic 11 1 0 0
+			>;
+	};
+};
+
+&dcsr {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "fsl,dcsr", "simple-bus";
+
+	dcsr-epu@0 {
+		compatible = "fsl,t1023-dcsr-epu", "fsl,dcsr-epu";
+		interrupts = <52 2 0 0
+			      84 2 0 0
+			      85 2 0 0>;
+		reg = <0x0 0x1000>;
+	};
+	dcsr-npc {
+		compatible = "fsl,t1023-dcsr-cnpc", "fsl,dcsr-cnpc";
+		reg = <0x1000 0x1000 0x1002000 0x10000>;
+	};
+	dcsr-nxc@2000 {
+		compatible = "fsl,dcsr-nxc";
+		reg = <0x2000 0x1000>;
+	};
+	dcsr-corenet {
+		compatible = "fsl,dcsr-corenet";
+		reg = <0x8000 0x1000 0x1A000 0x1000>;
+	};
+	dcsr-ocn@11000 {
+		compatible = "fsl,t1023-dcsr-ocn", "fsl,dcsr-ocn";
+		reg = <0x11000 0x1000>;
+	};
+	dcsr-ddr@12000 {
+		compatible = "fsl,dcsr-ddr";
+		dev-handle = <&ddr1>;
+		reg = <0x12000 0x1000>;
+	};
+	dcsr-nal@18000 {
+		compatible = "fsl,t1023-dcsr-nal", "fsl,dcsr-nal";
+		reg = <0x18000 0x1000>;
+	};
+	dcsr-rcpm@22000 {
+		compatible = "fsl,t1023-dcsr-rcpm", "fsl,dcsr-rcpm";
+		reg = <0x22000 0x1000>;
+	};
+	dcsr-snpc@30000 {
+		compatible = "fsl,t1023-dcsr-snpc", "fsl,dcsr-snpc";
+		reg = <0x30000 0x1000 0x1022000 0x10000>;
+	};
+	dcsr-snpc@31000 {
+		compatible = "fsl,t1023-dcsr-snpc", "fsl,dcsr-snpc";
+		reg = <0x31000 0x1000 0x1042000 0x10000>;
+	};
+	dcsr-cpu-sb-proxy@100000 {
+		compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu0>;
+		reg = <0x100000 0x1000 0x101000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@108000 {
+		compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu1>;
+		reg = <0x108000 0x1000 0x109000 0x1000>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "simple-bus";
+
+	soc-sram-error {
+		compatible = "fsl,soc-sram-error";
+		interrupts = <16 2 1 29>;
+	};
+
+	corenet-law@0 {
+		compatible = "fsl,corenet-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <16>;
+	};
+
+	ddr1: memory-controller@8000 {
+		compatible = "fsl,qoriq-memory-controller-v5.0",
+				"fsl,qoriq-memory-controller";
+		reg = <0x8000 0x1000>;
+		interrupts = <16 2 1 23>;
+	};
+
+	cpc: l3-cache-controller@10000 {
+		compatible = "fsl,t1023-l3-cache-controller", "cache";
+		reg = <0x10000 0x1000>;
+		interrupts = <16 2 1 27>;
+	};
+
+	corenet-cf@18000 {
+		compatible = "fsl,corenet2-cf";
+		reg = <0x18000 0x1000>;
+		interrupts = <16 2 1 31>;
+	};
+
+	iommu@20000 {
+		compatible = "fsl,pamu-v1.0", "fsl,pamu";
+		reg = <0x20000 0x1000>;
+		ranges = <0 0x20000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupts = <
+			24 2 0 0
+			16 2 1 30>;
+		pamu0: pamu@0 {
+			reg = <0 0x1000>;
+			fsl,primary-cache-geometry = <128 1>;
+			fsl,secondary-cache-geometry = <32 2>;
+		};
+	};
+
+/include/ "qoriq-mpic.dtsi"
+
+	guts: global-utilities@e0000 {
+		compatible = "fsl,t1023-device-config", "fsl,qoriq-device-config-2.0";
+		reg = <0xe0000 0xe00>;
+		fsl,has-rstcr;
+		fsl,liodn-bits = <12>;
+	};
+
+/include/ "qoriq-clockgen2.dtsi"
+	global-utilities@e1000 {
+		compatible = "fsl,t1023-clockgen", "fsl,qoriq-clockgen-2.0";
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 4>;
+			compatible = "fsl,core-mux-clock";
+			clocks = <&pll0 0>, <&pll0 1>;
+			clock-names = "pll0_0", "pll0_1";
+			clock-output-names = "cmux0";
+		};
+		mux1: mux1@20 {
+			#clock-cells = <0>;
+			reg = <0x20 4>;
+			compatible = "fsl,core-mux-clock";
+			clocks = <&pll0 0>, <&pll0 1>;
+			clock-names = "pll0_0", "pll0_1";
+			clock-output-names = "cmux1";
+		};
+	};
+
+	rcpm: global-utilities@e2000 {
+		compatible = "fsl,t1023-rcpm", "fsl,qoriq-rcpm-2.0";
+		reg = <0xe2000 0x1000>;
+	};
+
+	sfp: sfp@e8000 {
+		compatible = "fsl,t1023-sfp";
+		reg = <0xe8000 0x1000>;
+	};
+
+	serdes: serdes@ea000 {
+		compatible = "fsl,t1023-serdes";
+		reg = <0xea000 0x4000>;
+	};
+
+	scfg: global-utilities@fc000 {
+		compatible = "fsl,t1023-scfg";
+		reg = <0xfc000 0x1000>;
+	};
+
+/include/ "elo3-dma-0.dtsi"
+/include/ "elo3-dma-1.dtsi"
+
+/include/ "qoriq-espi-0.dtsi"
+	spi@110000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "qoriq-esdhc-0.dtsi"
+	sdhc@114000 {
+		compatible = "fsl,t1023-esdhc", "fsl,esdhc";
+		fsl,iommu-parent = <&pamu0>;
+		fsl,liodn-reg = <&guts 0x530>; /* eSDHCLIODNR */
+		sdhci,auto-cmd12;
+		no-1-8-v;
+	};
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-gpio-1.dtsi"
+/include/ "qoriq-gpio-2.dtsi"
+/include/ "qoriq-gpio-3.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+		usb0: usb@210000 {
+			compatible = "fsl-usb2-mph-v2.5", "fsl-usb2-mph";
+			fsl,iommu-parent = <&pamu0>;
+			fsl,liodn-reg = <&guts 0x520>; /* USB1LIODNR */
+			phy_type = "utmi";
+			port0;
+		};
+/include/ "qoriq-usb2-dr-0.dtsi"
+		usb1: usb@211000 {
+			compatible = "fsl-usb2-dr-v2.5", "fsl-usb2-dr";
+			fsl,iommu-parent = <&pamu0>;
+			fsl,liodn-reg = <&guts 0x524>; /* USB2LIODNR */
+			dr_mode = "host";
+			phy_type = "utmi";
+		};
+/include/ "qoriq-sata2-0.dtsi"
+sata@220000 {
+			fsl,iommu-parent = <&pamu0>;
+			fsl,liodn-reg = <&guts 0x550>; /* SATA1LIODNR */
+};
+
+/include/ "qoriq-sec5.0-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
new file mode 100644
index 0000000..8e4d9a6
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1024si-post.dtsi
@@ -0,0 +1,102 @@
+/*
+ * T1024 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "t1023si-post.dtsi"
+
+/ {
+	aliases {
+		vga = &display;
+		display = &display;
+	};
+
+	qe:qe@ffe140000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "qe";
+		compatible = "fsl,qe";
+		ranges = <0x0 0xf 0xfe140000 0x40000>;
+		reg = <0xf 0xfe140000 0 0x480>;
+		fsl,qe-num-riscs = <1>;
+		fsl,qe-num-snums = <28>;
+		brg-frequency = <0>;
+		bus-frequency = <0>;
+	};
+};
+
+&soc {
+/include/ "qoriq-tdm1.0.dtsi"
+
+	display:display@180000 {
+		compatible = "fsl,t1024-diu", "fsl,diu";
+		reg = <0x180000 1000>;
+		interrupts = <74 2 0 0>;
+	};
+};
+
+&qe {
+	qeic: interrupt-controller@80 {
+		interrupt-controller;
+		compatible = "fsl,qe-ic";
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x80 0x80>;
+		interrupts = <95 2 0 0  94 2 0 0>; //high:79 low:78
+	};
+
+	ucc@2000 {
+		cell-index = <1>;
+		reg = <0x2000 0x200>;
+		interrupts = <32>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@2200 {
+		cell-index = <3>;
+		reg = <0x2200 0x200>;
+		interrupts = <34>;
+		interrupt-parent = <&qeic>;
+	};
+
+	muram@10000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,qe-muram", "fsl,cpm-muram";
+		ranges = <0x0 0x10000 0x6000>;
+
+		data-only@0 {
+			compatible = "fsl,qe-muram-data", "fsl,cpm-muram-data";
+			reg = <0x0 0x6000>;
+		};
+	};
+};
diff --git a/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi b/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
new file mode 100644
index 0000000..1f1a9f8
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t102xsi-pre.dtsi
@@ -0,0 +1,87 @@
+/*
+ * T1024/T1023 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e5500_power_isa.dtsi"
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		ccsr = &soc;
+		dcsr = &dcsr;
+
+		dma0 = &dma0;
+		dma1 = &dma1;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		sdhc = &sdhc;
+
+		crypto = &crypto;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: PowerPC,e5500@0 {
+			device_type = "cpu";
+			reg = <0>;
+			clocks = <&mux0>;
+			next-level-cache = <&L2_1>;
+			L2_1: l2-cache {
+				next-level-cache = <&cpc>;
+			};
+		};
+		cpu1: PowerPC,e5500@1 {
+			device_type = "cpu";
+			reg = <1>;
+			clocks = <&mux1>;
+			next-level-cache = <&L2_2>;
+			L2_2: l2-cache {
+				next-level-cache = <&cpc>;
+			};
+		};
+	};
+};
-- 
2.1.0.27.g96db324

[PATCH 2/4 v3] powerpc/fsl-booke: Add T1024 QDS board support

[Shengzhou Liu]

Add support for Freescale T1024/T1023 QorIQ Development System Board.

T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.

T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- Ethernet interfaces:
  - Two 10M/100M/1G RGMII ports on-board
  - Three 1G/2.5Gbps SGMII ports
  - Four 1Gbps QSGMII ports
  - one 10Gbps XFI or 10G Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
  - Chrontel CH7201 for HDMI connection.
  - TI DS90C387R for direct LCD connection.
  - Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
  - 32-bit RISC controller for flexible support of the communications peripherals
  - Serial DMA channel for receive and transmit on all serial channels
  - Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep sleep power management implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A and one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v3: no change
v2: no change

 arch/powerpc/boot/dts/t1024qds.dts            | 251 ++++++++++++++++++++++++++
 arch/powerpc/platforms/85xx/Kconfig           |   2 +-
 arch/powerpc/platforms/85xx/corenet_generic.c |   1 +
 3 files changed, 253 insertions(+), 1 deletion(-)
 create mode 100644 arch/powerpc/boot/dts/t1024qds.dts

diff --git a/arch/powerpc/boot/dts/t1024qds.dts b/arch/powerpc/boot/dts/t1024qds.dts
new file mode 100644
index 0000000..14122cf
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1024qds.dts
@@ -0,0 +1,251 @@
+/*
+ * T1024 QDS Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+
+/ {
+	model = "fsl,T1024QDS";
+	compatible = "fsl,T1024QDS";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	ifc: localbus@ffe124000 {
+		reg = <0xf 0xfe124000 0 0x2000>;
+		ranges = <0 0 0xf 0xe8000000 0x08000000
+			  2 0 0xf 0xff800000 0x00010000
+			  3 0 0xf 0xffdf0000 0x00008000>;
+
+		nor@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x8000000>;
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		nand@2,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x2 0x0 0x10000>;
+		};
+
+		board-control@3,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,tetra-fpga", "fsl,fpga-qixis";
+			reg = <3 0 0x300>;
+			ranges = <0 3 0 0x300>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	dcsr: dcsr@f00000000 {
+		ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+	};
+
+	soc: soc@ffe000000 {
+		ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+		reg = <0xf 0xfe000000 0 0x00001000>;
+		spi@110000 {
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "micron,n25q128a11";  /* 16MB */
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+			};
+
+			flash@1 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "sst,sst25wf040";  /* 512KB */
+				reg = <1>;
+				spi-max-frequency = <10000000>;
+			};
+
+			flash@2 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "eon,en25s64";   /* 8MB */
+				reg = <2>;
+				spi-max-frequency = <10000000>;
+			};
+
+			slic@2 {
+				compatible = "maxim,ds26522";
+				reg = <2>;
+				spi-max-frequency = <2000000>;
+			};
+
+			slic@3 {
+				compatible = "maxim,ds26522";
+				reg = <3>;
+				spi-max-frequency = <2000000>;
+			};
+		};
+
+		i2c@118000 {
+			pca9547@77 {
+				compatible = "nxp,pca9547";
+				reg = <0x77>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+
+					eeprom@50 {
+						compatible = "at24,24c512";
+						reg = <0x50>;
+					};
+
+					eeprom@51 {
+						compatible = "at24,24c02";
+						reg = <0x51>;
+					};
+
+					eeprom@57 {
+						compatible = "at24,24c02";
+						reg = <0x57>;
+					};
+				};
+
+				i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+
+					ina220@40 {
+						compatible = "ti,ina220";
+						reg = <0x40>;
+						shunt-resistor = <1000>;
+					};
+
+					ina220@41 {
+						compatible = "ti,ina220";
+						reg = <0x41>;
+						shunt-resistor = <1000>;
+					};
+				};
+
+				i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x3>;
+
+					adt7461@4c {
+						/* Thermal Monitor */
+						compatible = "adi,adt7461";
+						reg = <0x4c>;
+					};
+
+					eeprom@55 {
+						compatible = "at24,24c02";
+						reg = <0x55>;
+					};
+
+					eeprom@56 {
+						compatible = "at24,24c512";
+						reg = <0x56>;
+					};
+
+					eeprom@57 {
+						compatible = "at24,24c512";
+						reg = <0x57>;
+					};
+				};
+			};
+			rtc@68 {
+				compatible = "dallas,ds3232";
+				reg = <0x68>;
+				interrupts = <0x5 0x1 0 0>;
+			};
+		};
+	};
+
+	pci0: pcie@ffe240000 {
+		reg = <0xf 0xfe240000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci1: pcie@ffe250000 {
+		reg = <0xf 0xfe250000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci2: pcie@ffe260000 {
+		reg = <0xf 0xfe260000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+};
+
+/include/ "fsl/t1024si-post.dtsi"
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 2fb4b24..e628d40 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -282,7 +282,7 @@ config CORENET_GENERIC
 	  For 64bit kernel, the following boards are supported:
 	    T208x QDS/RDB, T4240 QDS/RDB and B4 QDS
 	  The following boards are supported for both 32bit and 64bit kernel:
-	    P5020 DS, P5040 DS and T104xQDS/RDB
+	    P5020 DS, P5040 DS, T102x QDS, T104x QDS/RDB
 
 endif # FSL_SOC_BOOKE
 
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index 9824d2c..f61f477 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -150,6 +150,7 @@ static const char * const boards[] __initconst = {
 	"fsl,B4860QDS",
 	"fsl,B4420QDS",
 	"fsl,B4220QDS",
+	"fsl,T1024QDS",
 	"fsl,T1040QDS",
 	"fsl,T1042QDS",
 	"fsl,T1040RDB",
-- 
2.1.0.27.g96db324

[PATCH 3/4 v3] powerpc/fsl-booke: Add T1024 RDB board support

[Shengzhou Liu]

T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.

T1024RDB board Overview
-----------------------
- Processor: T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- Memory: 64-bit 4GB DDR3L UDIMM with ECC and interleaving support
- Ethernet: two 1G RGMII ports, one 2.5G SGMII port and one 10G Base-T port
- Accelerator: DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 1GB NAND Flash and CPLD system controlling
- PCIe: one PCIe slot and two Mini-PCIe connectors on-board
- USB: two Type-A USB2.0 ports with internal PHY
- eSDHC: one SDHC/MMC/eMMC connector
- eSPI: one 64MB N25Q512 SPI flash
- QE-TDM: support TDM Riser card
   - 32-bit RISC controller for flexible support of the communications peripherals
   - Serial DMA channel for receive and transmit on all serial channels
   - Two universal communication controllers, supporting TDM, HDLC, and UART
- I2C: four I2C controllers
- UART: two UART on board
- Deep sleep power management support

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v3: no change.
v2: Integrated scott's comments.

 arch/powerpc/boot/dts/t1024rdb.dts            | 185 ++++++++++++++++++++++++++
 arch/powerpc/platforms/85xx/Kconfig           |   2 +-
 arch/powerpc/platforms/85xx/corenet_generic.c |   1 +
 3 files changed, 187 insertions(+), 1 deletion(-)
 create mode 100644 arch/powerpc/boot/dts/t1024rdb.dts

diff --git a/arch/powerpc/boot/dts/t1024rdb.dts b/arch/powerpc/boot/dts/t1024rdb.dts
new file mode 100644
index 0000000..eb1d51b
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1024rdb.dts
@@ -0,0 +1,185 @@
+/*
+ * T1024 RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+
+/ {
+	model = "fsl,T1024RDB";
+	compatible = "fsl,T1024RDB";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	ifc: localbus@ffe124000 {
+		reg = <0xf 0xfe124000 0 0x2000>;
+		ranges = <0 0 0xf 0xe8000000 0x08000000
+			  2 0 0xf 0xff800000 0x00010000
+			  3 0 0xf 0xffdf0000 0x00008000>;
+
+		nor@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x8000000>;
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		nand@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x2 0x0 0x10000>;
+		};
+
+		board-control@2,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,t1024-cpld";
+			reg = <3 0 0x300>;
+			ranges = <0 3 0 0x300>;
+			bank-width = <1>;
+			device-width = <1>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	dcsr: dcsr@f00000000 {
+		ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+	};
+
+	soc: soc@ffe000000 {
+		ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+		reg = <0xf 0xfe000000 0 0x00001000>;
+		spi@110000 {
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "micron,n25q512ax3";
+				reg = <0>;
+				spi-max-frequency = <10000000>; /* input clk */
+			};
+
+			slic@1 {
+				compatible = "maxim,ds26522";
+				reg = <1>;
+				spi-max-frequency = <2000000>;
+			};
+
+			slic@2 {
+				compatible = "maxim,ds26522";
+				reg = <2>;
+				spi-max-frequency = <2000000>;
+			};
+		};
+
+		i2c@118000 {
+			adt7461@4c {
+				/* Thermal Monitor */
+				compatible = "adi,adt7461";
+				reg = <0x4c>;
+			};
+
+			eeprom@50 {
+				compatible = "at24,24c256";
+				reg = <0x50>;
+			};
+
+			rtc@68 {
+				compatible = "dallas,ds1339";
+				reg = <0x68>;
+				interrupts = <0x1 0x1 0 0>;
+			};
+		};
+
+		i2c@118100 {
+			pca9546@77 {
+				compatible = "nxp,pca9546";
+				reg = <0x77>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+
+	pci0: pcie@ffe240000 {
+		reg = <0xf 0xfe240000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci1: pcie@ffe250000 {
+		reg = <0xf 0xfe250000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci2: pcie@ffe260000 {
+		reg = <0xf 0xfe260000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+};
+
+/include/ "fsl/t1024si-post.dtsi"
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index e628d40..97915fe 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -282,7 +282,7 @@ config CORENET_GENERIC
 	  For 64bit kernel, the following boards are supported:
 	    T208x QDS/RDB, T4240 QDS/RDB and B4 QDS
 	  The following boards are supported for both 32bit and 64bit kernel:
-	    P5020 DS, P5040 DS, T102x QDS, T104x QDS/RDB
+	    P5020 DS, P5040 DS, T102x QDS/RDB, T104x QDS/RDB
 
 endif # FSL_SOC_BOOKE
 
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index f61f477..d7c1b4d 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -151,6 +151,7 @@ static const char * const boards[] __initconst = {
 	"fsl,B4420QDS",
 	"fsl,B4220QDS",
 	"fsl,T1024QDS",
+	"fsl,T1024RDB",
 	"fsl,T1040QDS",
 	"fsl,T1042QDS",
 	"fsl,T1040RDB",
-- 
2.1.0.27.g96db324

[PATCH 4/4 v3] powerpc/fsl-booke: Add T1023 RDB board support

[Shengzhou Liu]

T1023RDB is a Freescale Reference Design Board that hosts T1023 SoC.

T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - one 1G RGMII port on-board(RTL8211F PHY)
  - one 1G SGMII port on-board(RTL8211F PHY)
  - one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR:  128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC flash on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
---
v3: no change
v2: no change

 arch/powerpc/boot/dts/t1023rdb.dts            | 151 ++++++++++++++++++++++++++
 arch/powerpc/platforms/85xx/corenet_generic.c |   1 +
 2 files changed, 152 insertions(+)
 create mode 100644 arch/powerpc/boot/dts/t1023rdb.dts

diff --git a/arch/powerpc/boot/dts/t1023rdb.dts b/arch/powerpc/boot/dts/t1023rdb.dts
new file mode 100644
index 0000000..3780e68
--- /dev/null
+++ b/arch/powerpc/boot/dts/t1023rdb.dts
@@ -0,0 +1,151 @@
+/*
+ * T1023 RDB Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *	 notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *	 notice, this list of conditions and the following disclaimer in the
+ *	 documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *	 names of its contributors may be used to endorse or promote products
+ *	 derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/t102xsi-pre.dtsi"
+
+/ {
+	model = "fsl,T1023RDB";
+	compatible = "fsl,T1023RDB";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	ifc: localbus@ffe124000 {
+		reg = <0xf 0xfe124000 0 0x2000>;
+		ranges = <0 0 0xf 0xe8000000 0x08000000
+			  1 0 0xf 0xff800000 0x00010000>;
+
+		nor@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x8000000>;
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		nand@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x2 0x0 0x10000>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	dcsr: dcsr@f00000000 {
+		ranges = <0x00000000 0xf 0x00000000 0x01072000>;
+	};
+
+	soc: soc@ffe000000 {
+		ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+		reg = <0xf 0xfe000000 0 0x00001000>;
+		spi@110000 {
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "spansion,s25fl512s";
+				reg = <0>;
+				spi-max-frequency = <10000000>; /* input clk */
+			};
+		};
+
+		i2c@118000 {
+			eeprom@50 {
+				compatible = "stm,m24256";
+				reg = <0x50>;
+			};
+
+			rtc@68 {
+				compatible = "dallas,ds1339";
+				reg = <0x68>;
+				interrupts = <0x5 0x1 0 0>;
+			};
+		};
+
+		i2c@118100 {
+		};
+	};
+
+	pci0: pcie@ffe240000 {
+		reg = <0xf 0xfe240000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8000000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci1: pcie@ffe250000 {
+		reg = <0xf 0xfe250000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x10000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8010000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci2: pcie@ffe260000 {
+		reg = <0xf 0xfe260000 0 0x10000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x10000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+};
+
+/include/ "fsl/t1023si-post.dtsi"
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index d7c1b4d..bd839dc 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -150,6 +150,7 @@ static const char * const boards[] __initconst = {
 	"fsl,B4860QDS",
 	"fsl,B4420QDS",
 	"fsl,B4220QDS",
+	"fsl,T1023RDB",
 	"fsl,T1024QDS",
 	"fsl,T1024RDB",
 	"fsl,T1040QDS",
-- 
2.1.0.27.g96db324

Re: [2/4,v3] powerpc/fsl-booke: Add T1024 QDS board support

[Scott Wood]

On Thu, Apr 09, 2015 at 04:07:43PM +0800, Shengzhou Liu wrote:
> +			flash@2 {
> +				#address-cells = <1>;
> +				#size-cells = <1>;
> +				compatible = "eon,en25s64";   /* 8MB */
> +				reg = <2>;
> +				spi-max-frequency = <10000000>;
> +			};

AFAICT the vendor is phyton, not eon.

> +					eeprom@50 {
> +						compatible = "at24,24c512";
> +						reg = <0x50>;
> +					};
> +
> +					eeprom@51 {
> +						compatible = "at24,24c02";
> +						reg = <0x51>;
> +					};
> +
> +					eeprom@57 {
> +						compatible = "at24,24c02";
> +						reg = <0x57>;
> +					};

The vendor is atmel, not at24.

I'll fix when applying, but please be careful with compatible strings
next time.  Also, please document compatible strings and vendor prefixes
when checkpatch complains, unless it's a situation where checkpatch isn't
recognizing a pattern compatible (e.g.  "fsl,<soc>-whatever" or
"fsl,whatever-<version>").

This patch also had too long lines in the commit message (and really, you
don't need to describe the board in such detail).  I'll remove that
section of the changelog when applying.

-Scott

Re: [4/4,v3] powerpc/fsl-booke: Add T1023 RDB board support

[Scott Wood]

On Thu, Apr 09, 2015 at 04:07:45PM +0800, Shengzhou Liu wrote:
> +		i2c@118000 {
> +			eeprom@50 {
> +				compatible = "stm,m24256";
> +				reg = <0x50>;
> +			};

Vendor prefix is "st", not "stm" -- see
Documentation/devicetree/bindings/vendor-prefixes.txt

I'll fix when applying.

-Scott

RE: [2/4,v3] powerpc/fsl-booke: Add T1024 QDS board support

[Liu Shengzhou]

> Subject: Re: [2/4,v3] powerpc/fsl-booke: Add T1024 QDS board support
>=20
> On Thu, Apr 09, 2015 at 04:07:43PM +0800, Shengzhou Liu wrote:
> > +			flash@2 {
> > +				#address-cells =3D <1>;
> > +				#size-cells =3D <1>;
> > +				compatible =3D "eon,en25s64";   /* 8MB */
> > +				reg =3D <2>;
> > +				spi-max-frequency =3D <10000000>;
> > +			};
>=20
> AFAICT the vendor is phyton, not eon.

How do you think the vendor is phyton?
Per en25s64 data sheet, it's really EON (Eon Silicon Solution, Inc,  www.eo=
nssi.com)
I had sent a patch for EON http://patchwork.ozlabs.org/patch/367810/ last y=
ear.
There is no 'phyton' in binding document.=20

Re: [2/4,v3] powerpc/fsl-booke: Add T1024 QDS board support

[Scott Wood]

On Mon, 2015-06-01 at 03:23 -0500, Liu Shengzhou-B36685 wrote:
> > Subject: Re: [2/4,v3] powerpc/fsl-booke: Add T1024 QDS board 
> > support
> > 
> > On Thu, Apr 09, 2015 at 04:07:43PM +0800, Shengzhou Liu wrote:
> > > +                  flash@2{
> > > +                         #address-cells = <1>;
> > > +                         #size-cells = <1>;
> > > +                         compatible = "eon,en25s64";   /* 8MB */
> > > +                         reg = <2>;
> > > +                         spi-max-frequency = <10000000>;
> > > +                 };
> > 
> > AFAICT the vendor is phyton, not eon.
> 
> How do you think the vendor is phyton?
> Per en25s64 data sheet, it's really EON (Eon Silicon Solution, Inc,  
> www.eonssi.com)

I'm not sure.  The search results for it look a bit different from 
what I remember seeing last week.  I'll fix it.

> I had sent a patch for EON  http://patchwork.ozlabs.org/patch/367810/
> last year.
> There is no 'phyton' in binding document. 

There is no binding document.  As for vendor-prefixes, you should ping 
to get that patch merged -- and when you're depending on an unmerged 
patch (even if just documentation), please mention it below the --- 
line when submitting.

-Scott