Re: After Uncompresseing Linux..., what's next

[Prakash kanthi <pkanthi@yahoo.com>]

I found the correct exception guys. It means
Privileged Instruction Exception.

--- Prakash kanthi <pkanthi@yahoo.com> wrote:
>
> Folks,
>
> I just wanted to provide more info on my env. I have
> PPC405 based board with no network support forcing
> me
> to use zImage.initrd.elf.
>
> Can you suggest more on my problem described below?
> I
> saw the memory values at 0x00000000 onwards after
> uncompressing linux and they have changed. But when
> the control jumps to 0x0, my board hangs. I see that
> ESR is showing a value of 0x80000000, meaning either
> illegal instruction or Machine Check.
>
> Can you tell what's going on? What happens next
> after
> uncompressing? I am thinking it executes
> start_kernel
> function which calls lock_kernel. Let me know if i
> am
> wrong.
>
> thanks,
> Prakash
>
>
>
>
> --- James Don <JDon@spacebridge.com> wrote:
> > I just went thru this myself ... ;-)
> >
> > 1.) Get a BDM/JTAG tool look halt the processor
> > after you see " Now booting
> > the kernel" and look for valid asm at 0x0 ... make
> > sure it mathes your
> > start.s file ...
> >
> > 2.) Veryfy you have your mem map from ppcboot
> > matching requirements for the
> > kernel i.e ram (physical=0x0, virtual=0xc0000000)
> > and immr (phys 0xff000000
> > virtual 0xff000000) ... I had my immr in ppc boot
> at
> > 0x02200000 this screwed
> > me for quite a while ... otherwise you have no
> > printk ... the memory map is
> > very important not to screw with some things
> depend
> > on it (unless your
> > careful) ...
> >
> > 3.) verify you SMC1 (uart) is getting proper
> > clocking config ... i.e
> > bus->brg1 and brg1 is 16 times baud rate ...
> > otherwise you have no printk
> >
> > 4.) and always always keep in mind your RAM refesh
> > could be wrong ...
> > everyone will tell you this even when it has
> nothing
> > to do with your problem
> > ... try not to ignore them if you are still stuck
> > ;-) But verifying step 1
> > should prove your ok ...
> >
> > Best of luck,
> > Jim
> >
> >
> > -----Original Message-----
> > From: Prakash kanthi [mailto:pkanthi@yahoo.com]
> > Sent: Wednesday, December 18, 2002 7:14 PM
> > To: LinuxPPC
> > Subject: After Uncompresseing Linux..., what's
> next
> >
> >
> > Hi there,
> >
> > I was trying to load linuxppc_2_4_devel onto my
> > board.
> > It goes through the board info read, UART init and
> > Uncompressing the linux kernel. But after that, i
> do
> > not see any messages and board hangs.
> >
> > Here is the UART output:
> > ------------------------------------
> > OS Booting...
> >
> > loaded at:     00400000 0060D1CC
> > board data at: 00000030 00000044
> > relocated to:  00405C24 00405C38
> > zimage at:     00406290 004A08FF
> > initrd at:     004A1000 006097CA
> > avail ram:     0060E000 007F8000
> >
> > Linux/PPC load: console=ttyS0,9600 console=tty1
> > ip=on
> > root=/dev/xsysace/disc0/pa
> > rt3 rw
> > Uncompressing Linux...done.
> > Now booting the kernel
> > -------------------------------------------
> >
> > After the last line, it hangs. I get a feeling
> that,
> > the uncompressing process is not writing in the
> > memory
> > starting from 0x00000000 and, after uncompressing,
> > it
> > is jumping into 0x00000000 and is not able to find
> > anything.
> >
> > My questions are,
> > 1. How can i make sure that, the uncompressing
> > process
> > is going to start writing the data from
> 0x00000000.
> >
> > 2. How big a space this uncompressing process
> needs?
> > And also how much overall memory is required for
> > running linux. I just have 8MB SDRAM.
> >
> > 3. What is the next step in the booting process?
> > Which
> > Device (eth, pci, ide, ???) Initialization?
> >
> > Your help is appreciated.
> >
> > thanks,
> > Prakash
> >
> >
>
>
>


** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/