Re: how to make a PCI net card work on ICECUBE ?

Re: how to make a PCI net card work on ICECUBE ?

[debora liu]
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how to make a PCI net card work on ICECUBE ?

[ÏÄÓê]

Thanks for your help.

I found out that the ICECUBE board could tftpboot via the PCI netcard if wire net to the card, but the board could not mount NFS via the card.

So i set the environment ethact to i82559#0 and saveenv , but the board still could not mount NFS via the card.During the booting-up ,there was nothing about eth1 shown .

And i wired net to the FEC ethernet port,reset the board,found that the environment ethact was now FEC ETHERNET,so i set it again to i82559#0 and saveenv,booted up the kernel, there was nothing about eth1 shown , i tried ifconfig eth1 * up ,information were below: 

bash-2.05b# ifconfig eth1 198.87.102.218 up
SIOCSIFADDR: No such device
eth1: unknown interface: No such device
eth1: unknown interface: No such device 

where did i make mistakes ?

Best Regards

xiayu 

Re: how to make a PCI net card work on ICECUBE ?

[Wolfgang Denk]

In message <200509291156.AA2359564@NARI-RELAYS.COM> you wrote:
> 
> I found out that the ICECUBE board could tftpboot via the PCI netcard if wire net to the card, but the board could not mount NFS via the card.
> 
> So i set the environment ethact to i82559#0 and saveenv , but the board still could not mount NFS via the card.During the booting-up ,there was nothing about eth1 shown .
...
> bash-2.05b# ifconfig eth1 198.87.102.218 up
> SIOCSIFADDR: No such device
> eth1: unknown interface: No such device
> eth1: unknown interface: No such device 
> 
> where did i make mistakes ?

I guess you forgot to configure the correct driver for  your  network
card into your Linux kernel.

Best regards,

Wolfgang Denk

-- 
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de
Old programmers never die, they just branch to a new address.