From: "KylongMu" <mqy@263.net.cn>
To: <linuxppc-embedded@ozlabs.org>
Subject: 11-16-05 2.6.14 on AMCC Yosemite board(PCI-IDE card boot error)
Date: Wed, 16 Nov 2005 20:18:31 +0800 [thread overview]
Message-ID: <20051116121846.1C1BD1FD0@smtp.263.net> (raw)
In-Reply-To:
[-- Attachment #1.1: Type: text/plain, Size: 1256 bytes --]
Dear Denk,
Thanks for your help; it makes my Yosemite run up! I'm try to add a
PCI-IDE
Card on it. I test my Promise-PDC20268 card and AEC6280 (ATP865-B chip type)
card,
Both of them all failed with same error, the boot message included in the
attachment.
The kernel configure is based on the Yosemite_defconfig, add with:
Device Drivers-->
ATA/ATAPI/MFM/RLL support-->
[*]AEC62XX Chipset support
[*]PROMISE
PDC202{68|69|70|71|75|76|77} SUPPORT
Both of the PCI-IDE cards can work with X86PC+FEDORA4 configure, I
don't know
What cause them fail on Yosemite with final 2.6.14 kernel.
About my 2.6.14 tree, I type with "cg-log -s" command it shows:
99a21389c2b0e55f30b6cf6550cb492b87dbaa3b Heiko Schocher 2005-11-11 12:47
[PATCH] ppc32: fix Kernel Panic for PM82x Board with gcc-4.0.
ff1df84b3c3154ffdb646941e1c70d17554e3042 Wolfgang Denk 2005-11-10 00:41
Merge with /home/wd/git/linux-2.6/stefan_roese
It only shows 2.6.14 on the kernel message, I don't know why it doesn't
show the message as you told.
But it can work, and fixed the bugs on Yosemite.
Cordially,
Kylong Mu
[-- Attachment #1.2: Type: text/html, Size: 10598 bytes --]
[-- Attachment #2: bootmessage(acard6280 pci-ide card).txt --]
[-- Type: text/plain, Size: 6044 bytes --]
U-Boot 1.1.4 (Nov 11 2005 - 19:35:30)
AMCC PowerPC 440EP Rev. B
Board: Yosemite - AMCC PPC440EP Evaluation Board
VCO: 1066 MHz
CPU: 533 MHz
PLB: 133 MHz
OPB: 66 MHz
EPB: 66 MHz
PCI: 66 MHz
I2C: ready
DRAM: 256 MB
FLASH: 64 MB
PCI: Bus Dev VenId DevId Class Int
00 0c 1191 0009 0180 00
In: serial
Out: serial
Err: serial
Net: ppc_4xx_eth0, ppc_4xx_eth1
Type "run flash_nfs" to mount root filesystem over NFS
Hit any key to stop autoboot: 0
=> tftp 400000 uImage
ENET Speed is 100 Mbps - FULL duplex connection
Using ppc_4xx_eth0 device
TFTP from server 192.168.0.93; our IP address is 192.168.0.66
Filename 'uImage'.
Load address: 0x400000
Loading: #################################################################
#################################################################
#################################################################
###########################################
done
Bytes transferred = 1217393 (129371 hex)
=> bootram
Unknown command 'bootram' - try 'help'
=> run bootram
## Booting image at 00400000 ...
Image Name: Linux-2.6.14
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1217329 Bytes = 1.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at fed40000 ...
Image Name: Yosemite Ramdisk
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 17770706 Bytes = 16.9 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Ramdisk to 0ee47000, end 0ff398d2 ... OK
Linux version 2.6.14 (root@dxp) (gcc version 4.0.0) #7 Sun Nov 13 21:59:01 CST 2005
AMCC PowerPC 440EP Yosemite Platform
Built 1 zonelists
Kernel command line: ramdisk_size=49152 root=/dev/ram rw ip=192.168.0.66:192.168.0.93::255.255.255.0:yosemite:eth0:off panic=1 console=ttyS0,115200
PID hash table entries: 2048 (order: 11, 32768 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 239616k available (1860k kernel code, 596k data, 140k init, 0k highmem)
Mount-cache hash table entries: 512
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
softlockup thread 0 started up.
Freeing initrd memory: 17354k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
usbcore: registered new driver usbfs
usbcore: registered new driver hub
SCSI subsystem initialized
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
usbmon: debugfs is not available
ppc-soc-ohci ppc-soc-ohci.0: USB Host Controller
ppc-soc-ohci ppc-soc-ohci.0: new USB bus registered, assigned bus number 1
ppc-soc-ohci ppc-soc-ohci.0: irq 40, io mem 0xef601000
usb usb1: Product: USB Host Controller
usb usb1: Manufacturer: Linux 2.6.14 ohci_hcd
usb usb1: SerialNumber: PPC-SOC USB
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 0) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 1) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 49152K size 1024 blocksize
PPC 4xx OCP EMAC driver, version 3.53
mal0: initialized, 4 TX channels, 2 RX channels
zmii0: bridge in RMII mode
eth0: emac0, MAC 00:10:ec:00:87:40
eth0: found Generic MII PHY (0x01)
eth1: emac1, MAC 00:10:ec:00:87:47
eth1: found Generic MII PHY (0x03)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Data machine check in kernel mode.
PLB0: BEAR=0x0000000000000000 ACR= 0x00000000 BESR= 0xfffff7ff
POB0: BEAR=0xc27e3194ffffffff BESR0=0x00000000 BESR1=0x00000000
OPB0: BEAR=0x0000000000000151 BSTAT=0x00000000
Oops: machine check, sig: 7 [#1]
NIP: 00000000 LR: C0263628 SP: CFF41F40 REGS: c0271f50 TRAP: 0202 Not tainted
MSR: 00000000 EE: 0 PR: 0 FP: 0 ME: 0 IR/DR: 00
TASK = c04f8b10[1] 'swapper' THREAD: cff40000
Last syscall: 120
GPR00: FDFFEF02 CFF41F40 C04F8B10 C04FC000 C026C6B4 C04FC000 00000009 CFF41EF4
GPR08: C04F9F70 00000000 00004000 C0270000 24254322 61000408 0FFB6800 00000001
GPR16: 00800000 0FFCEAD4 FFFFFFFF 00000000 007FFF00 0FFB1210 00000003 00000002
GPR24: C01D0000 C01D0000 C0270000 C01D0000 C0270000 C0223E10 C026C6B4 C04FC000
NIP [00000000] 0x0
LR [c0263628] aec62xx_init_one+0x38/0x48
Call trace:
[c0263628] aec62xx_init_one+0x38/0x48
[c02649b8] ide_scan_pcidev+0x68/0xb0
[c0264a34] ide_scan_pcibus+0x34/0xe8
[c026492c] ide_init+0x68/0x8c
[c00013ac] init+0xb4/0x254
[c00046c0] kernel_thread+0x48/0x64
Data machine check in kernel mode.
PLB0: BEAR=0x0000000000000000 ACR= 0x00000000 BESR= 0xfffff7ff
POB0: BEAR=0xc27e3194ffffffff BESR0=0x00000000 BESR1=0x00000000
OPB0: BEAR=0x0000000000000151 BSTAT=0x00000000
Oops: machine check, sig: 7 [#2]
NIP: 00000000 LR: C000235C SP: C0271E70 REGS: c0271f50 TRAP: 0202 Not tainted
MSR: 00000000 EE: 0 PR: 0 FP: 0 ME: 0 IR/DR: 00
TASK = c04f8b10[1] 'swapper' THREAD: cff40000
Last syscall: 120
GPR00: 08000000 C0271E70 C04F8B10 C0271E80 00001568 FFFFFFFF C0270000 00004000
GPR08: C0270000 C000235C 00021002 C00039E8 C04F8CD8 61000408 0FFB6800 00000001
GPR16: 00800000 0FFCEAD4 FFFFFFFF 00000000 007FFF00 0FFB1210 00000003 00000002
GPR24: C01D0000 C01D0000 C0270000 C01D0000 C0270000 C0223E10 00000007 C0271F50
NIP [00000000] 0x0
LR [c000235c] ret_from_except+0x0/0x18
Kernel panic - not syncing: Attempted to kill init!
<0>Rebooting in 1 seconds..
next reply other threads:[~2005-11-16 12:18 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-11-16 12:18 KylongMu [this message]
2005-11-17 15:05 ` 11-16-05 2.6.14 on AMCC Yosemite board(PCI-IDE card boot error) Stefan Roese
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20051116121846.1C1BD1FD0@smtp.263.net \
--to=mqy@263.net.cn \
--cc=linuxppc-embedded@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).