From: David Gibson <david@gibson.dropbear.id.au>
To: "Mark A. Greer" <mgreer@mvista.com>
Cc: linuxppc-dev <Linuxppc-dev@ozlabs.org>,
Paul Mackerras <paulus@samba.org>
Subject: Re: [PATCH 1/13] powerpc: Add Makefile rules to wrap dts file in zImage
Date: Tue, 22 May 2007 10:23:49 +1000 [thread overview]
Message-ID: <20070522002349.GA25426@localhost.localdomain> (raw)
In-Reply-To: <20070521181043.GB7120@mag.az.mvista.com>
On Mon, May 21, 2007 at 11:10:43AM -0700, Mark A. Greer wrote:
> On Mon, May 14, 2007 at 10:33:32AM +1000, David Gibson wrote:
> > On Fri, May 11, 2007 at 05:53:36PM -0700, Mark A. Greer wrote:
> > > +$(obj)/zImage.dts: $(addprefix $(obj)/, $(dts-y))
> > > + @rm -f $@; ln $< $@
> > > +$(obj)/zImage.dts_initrd: $(addprefix $(obj)/, $(dts_initrd-y))
> > > + @rm -f $@; ln $< $@
> > > +
> >
> > I thought you said you were going to drop this bit?
>
> Hi David.
>
> Would you elaborate on what your alternative is? A lot of the Makefile
> stuff is still black magic to me.
Just leave them out. As long as you add the correct specific
zImage.dts.% and zImage.dts_initrd.% targets to image-y and initrd-y,
then a "make zImage" from the top-level Makefile will get them built.
You'd want to remove the .dts versions from BOOT_TARGETS, too.
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
next prev parent reply other threads:[~2007-05-22 0:23 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-05-12 0:46 [PATCH 0/13] powerpc: Add support for Marvell/mv64x60 and prpmc2800 Mark A. Greer
2007-05-12 0:53 ` [PATCH 1/13] powerpc: Add Makefile rules to wrap dts file in zImage Mark A. Greer
2007-05-14 0:33 ` David Gibson
2007-05-14 3:46 ` Mark A. Greer
2007-05-14 3:49 ` David Gibson
2007-05-21 18:10 ` Mark A. Greer
2007-05-22 0:23 ` David Gibson [this message]
2007-05-24 21:28 ` Mark A. Greer
2007-05-25 1:32 ` David Gibson
2007-05-25 1:33 ` David Gibson
2007-05-25 20:50 ` Mark A. Greer
2007-05-28 4:43 ` David Gibson
2007-05-12 0:54 ` [PATCH 2/13] powerpc: Add bootwrapper support for Marvell/mv64x60 hostbridge Mark A. Greer
2007-05-12 0:54 ` [PATCH 3/13] powerpc: Add bootwrapper support for Marvell MPSC Mark A. Greer
2007-05-12 0:54 ` [PATCH 4/13] powerpc: Add bootwrapper support for Marvell/mv64x60 I2C Mark A. Greer
2007-05-12 0:55 ` [PATCH 5/13] powerpc: Add interrupt support for Marvell mv64x60 chips Mark A. Greer
2007-05-12 0:55 ` [PATCH 6/13] powerpc: Create Marvell mv64x60 MPSC (serial) platform_data Mark A. Greer
2007-05-12 0:56 ` [PATCH 7/13] powerpc: Create Marvell mv64x60 ethernet platform_data Mark A. Greer
2007-05-12 0:56 ` [PATCH 8/13] powerpc: Create Marvell mv64x60 I2C platform_data Mark A. Greer
2007-05-12 0:57 ` [PATCH 9/13] powerpc: Add Marvell mv64x60 PCI bridge support Mark A. Greer
2007-05-12 0:57 ` [PATCH 10/13] powerpc: check cache coherency of kernel vs firmware Mark A. Greer
2007-05-14 0:40 ` David Gibson
2007-05-14 12:34 ` Segher Boessenkool
2007-05-14 14:44 ` Dale Farnsworth
2007-05-14 20:27 ` Mark A. Greer
2007-05-12 0:57 ` [PATCH 11/13] powerpc: Add DTS file for the Motorola PrPMC2800 platform Mark A. Greer
2007-05-12 0:58 ` [PATCH 12/13] powerpc: Add bootwrapper support for " Mark A. Greer
2007-05-12 0:58 ` [PATCH 13/13] powerpc: Add arch/powerpc support for the Motorola PrPMC2800 Mark A. Greer
-- strict thread matches above, loose matches on Subject: below --
2007-05-10 20:02 [PATCH 0/13] powerpc: Add support for Marvell/mv64x60 and prpmc2800 Mark A. Greer
2007-05-10 20:04 ` [PATCH 1/13] powerpc: Add Makefile rules to wrap dts file in zImage Mark A. Greer
2007-05-10 23:29 ` David Gibson
2007-05-11 15:59 ` Mark A. Greer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070522002349.GA25426@localhost.localdomain \
--to=david@gibson.dropbear.id.au \
--cc=Linuxppc-dev@ozlabs.org \
--cc=mgreer@mvista.com \
--cc=paulus@samba.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).