* [patch 00/14] Current 4xx patch series
@ 2007-07-17 18:15 Josh Boyer
2007-07-17 18:15 ` [patch 01/14] Use resource_size_t for serial port IO addresses Josh Boyer
` (13 more replies)
0 siblings, 14 replies; 22+ messages in thread
From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw)
To: linuxppc-dev
For those interested, here's my current 4xx patch series. There are a few
cleanups as a pre-requisite for 40x support, some minimal Walnut support, and
another round of Bamboo patches. These are all based off of Paul's current
tree.
Patches 1 through 7 are likely ready to be merged if there are no large
objections. The Walnut stuff likely needs another round or two. The Bamboo
patches can likely go in, but there is no rush there.
Ethernet for 4xx in general is still provided by the out-of-tree emac rewrite
that Ben and David have poked at. If it doesn't get merged soon, I'll take
a look at getting it working again.
As an aside, I'll likely be setting up a git tree for 4xx soon. Hopefully
that will help with some of the larger-ish patches.
josh
--
^ permalink raw reply [flat|nested] 22+ messages in thread* [patch 01/14] Use resource_size_t for serial port IO addresses 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:15 ` [patch 02/14] Rename 4xx paths to 40x Josh Boyer ` (12 subsequent siblings) 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev; +Cc: David Gibson At present, various parts of the serial code use unsigned long to define resource addresses. This is a problem, because some 32-bit platforms have physical addresses larger than 32-bits, and have mmio serial uarts located above the 4GB point. This patch changes the type of mapbase in both struct uart_port and struct plat_serial8250_port to resource_size_t, which can be configured to be 64 bits on such platforms. The mapbase in serial_struct can't safely be changed, because that structure is user visible. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- drivers/serial/8250.c | 5 +++-- drivers/serial/8250_early.c | 16 +++++++++------- drivers/serial/serial_core.c | 9 +++++---- include/linux/serial_8250.h | 2 +- include/linux/serial_core.h | 2 +- 5 files changed, 19 insertions(+), 15 deletions(-) --- linux-2.6.orig/include/linux/serial_core.h +++ linux-2.6/include/linux/serial_core.h @@ -284,7 +284,7 @@ struct uart_port { const struct uart_ops *ops; unsigned int custom_divisor; unsigned int line; /* port index */ - unsigned long mapbase; /* for ioremap */ + resource_size_t mapbase; /* for ioremap */ struct device *dev; /* parent device */ unsigned char hub6; /* this should be in the 8250 driver */ unsigned char unused[3]; --- linux-2.6.orig/drivers/serial/serial_core.c +++ linux-2.6/drivers/serial/serial_core.c @@ -626,7 +626,7 @@ static int uart_get_info(struct uart_sta tmp.hub6 = port->hub6; tmp.io_type = port->iotype; tmp.iomem_reg_shift = port->regshift; - tmp.iomem_base = (void *)port->mapbase; + tmp.iomem_base = (void *)(unsigned long)port->mapbase; if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) return -EFAULT; @@ -1666,10 +1666,11 @@ static int uart_line_info(char *buf, str return 0; mmio = port->iotype >= UPIO_MEM; - ret = sprintf(buf, "%d: uart:%s %s%08lX irq:%d", + ret = sprintf(buf, "%d: uart:%s %s%08llX irq:%d", port->line, uart_type(port), mmio ? "mmio:0x" : "port:", - mmio ? port->mapbase : (unsigned long) port->iobase, + mmio ? (unsigned long long)port->mapbase + : (unsigned long long) port->iobase, port->irq); if (port->type == PORT_UNKNOWN) { @@ -2063,7 +2064,7 @@ uart_report_port(struct uart_driver *drv case UPIO_TSI: case UPIO_DWAPB: snprintf(address, sizeof(address), - "MMIO 0x%lx", port->mapbase); + "MMIO 0x%llx", (unsigned long long)port->mapbase); break; default: strlcpy(address, "*unknown*", sizeof(address)); --- linux-2.6.orig/drivers/serial/8250_early.c +++ linux-2.6/drivers/serial/8250_early.c @@ -145,8 +145,9 @@ static int __init parse_options(struct e port->mapbase = simple_strtoul(options + 5, &options, 0); port->membase = ioremap(port->mapbase, mapsize); if (!port->membase) { - printk(KERN_ERR "%s: Couldn't ioremap 0x%lx\n", - __FUNCTION__, port->mapbase); + printk(KERN_ERR "%s: Couldn't ioremap 0x%llx\n", + __FUNCTION__, + (unsigned long long)port->mapbase); return -ENOMEM; } mmio = 1; @@ -168,9 +169,10 @@ static int __init parse_options(struct e device->baud); } - printk(KERN_INFO "Early serial console at %s 0x%lx (options '%s')\n", + printk(KERN_INFO "Early serial console at %s 0x%llx (options '%s')\n", mmio ? "MMIO" : "I/O port", - mmio ? port->mapbase : (unsigned long) port->iobase, + mmio ? (unsigned long long) port->mapbase + : (unsigned long long) port->iobase, device->options); return 0; } @@ -236,10 +238,10 @@ static int __init early_uart_console_swi mmio = (port->iotype == UPIO_MEM); line = serial8250_start_console(port, device->options); if (line < 0) - printk("No ttyS device at %s 0x%lx for console\n", + printk("No ttyS device at %s 0x%llx for console\n", mmio ? "MMIO" : "I/O port", - mmio ? port->mapbase : - (unsigned long) port->iobase); + mmio ? (unsigned long long) port->mapbase + : (unsigned long long) port->iobase); unregister_console(&early_uart_console); if (mmio) --- linux-2.6.orig/include/linux/serial_8250.h +++ linux-2.6/include/linux/serial_8250.h @@ -20,7 +20,7 @@ struct plat_serial8250_port { unsigned long iobase; /* io base address */ void __iomem *membase; /* ioremap cookie or NULL */ - unsigned long mapbase; /* resource base */ + resource_size_t mapbase; /* resource base */ unsigned int irq; /* interrupt number */ unsigned int uartclk; /* UART clock rate */ unsigned char regshift; /* register shift */ --- linux-2.6.orig/drivers/serial/8250.c +++ linux-2.6/drivers/serial/8250.c @@ -2664,8 +2664,9 @@ static int __devinit serial8250_probe(st ret = serial8250_register_port(&port); if (ret < 0) { dev_err(&dev->dev, "unable to register port at index %d " - "(IO%lx MEM%lx IRQ%d): %d\n", i, - p->iobase, p->mapbase, p->irq, ret); + "(IO%lx MEM%llx IRQ%d): %d\n", i, + p->iobase, (unsigned long long)p->mapbase, + p->irq, ret); } } return 0; -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 02/14] Rename 4xx paths to 40x 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer 2007-07-17 18:15 ` [patch 01/14] Use resource_size_t for serial port IO addresses Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-18 3:26 ` David Gibson 2007-07-17 18:15 ` [patch 03/14] 4xx Kconfig cleanup Josh Boyer ` (11 subsequent siblings) 13 siblings, 1 reply; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev 4xx is a bit of a misnomer for certain things, as they really apply to PowerPC 40x only. Rename some of the files to clean this up. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/Makefile | 2 arch/powerpc/kernel/Makefile | 2 arch/powerpc/kernel/head_40x.S | 1021 ++++++++++++++++++++++++++++++++++++ arch/powerpc/kernel/head_4xx.S | 1021 ------------------------------------ arch/powerpc/mm/40x_mmu.c | 135 ++++ arch/powerpc/mm/4xx_mmu.c | 135 ---- arch/powerpc/mm/Makefile | 2 arch/powerpc/platforms/40x/Kconfig | 208 +++++++ arch/powerpc/platforms/40x/Makefile | 1 arch/powerpc/platforms/4xx/Kconfig | 208 ------- arch/powerpc/platforms/4xx/Makefile | 1 11 files changed, 1368 insertions(+), 1368 deletions(-) --- linux-2.6.orig/arch/powerpc/Makefile +++ linux-2.6/arch/powerpc/Makefile @@ -123,7 +123,7 @@ CFLAGS += $(cpu-as-y) head-y := arch/powerpc/kernel/head_32.o head-$(CONFIG_PPC64) := arch/powerpc/kernel/head_64.o head-$(CONFIG_8xx) := arch/powerpc/kernel/head_8xx.o -head-$(CONFIG_4xx) := arch/powerpc/kernel/head_4xx.o +head-$(CONFIG_40x) := arch/powerpc/kernel/head_40x.o head-$(CONFIG_44x) := arch/powerpc/kernel/head_44x.o head-$(CONFIG_FSL_BOOKE) := arch/powerpc/kernel/head_fsl_booke.o --- linux-2.6.orig/arch/powerpc/kernel/Makefile +++ linux-2.6/arch/powerpc/kernel/Makefile @@ -46,7 +46,7 @@ ifeq ($(CONFIG_PPC_MERGE),y) extra-$(CONFIG_PPC_STD_MMU) := head_32.o extra-$(CONFIG_PPC64) := head_64.o -extra-$(CONFIG_40x) := head_4xx.o +extra-$(CONFIG_40x) := head_40x.o extra-$(CONFIG_44x) := head_44x.o extra-$(CONFIG_FSL_BOOKE) := head_fsl_booke.o extra-$(CONFIG_8xx) := head_8xx.o --- /dev/null +++ linux-2.6/arch/powerpc/kernel/head_40x.S @@ -0,0 +1,1021 @@ +/* + * Copyright (c) 1995-1996 Gary Thomas <gdt@linuxppc.org> + * Initial PowerPC version. + * Copyright (c) 1996 Cort Dougan <cort@cs.nmt.edu> + * Rewritten for PReP + * Copyright (c) 1996 Paul Mackerras <paulus@cs.anu.edu.au> + * Low-level exception handers, MMU support, and rewrite. + * Copyright (c) 1997 Dan Malek <dmalek@jlc.net> + * PowerPC 8xx modifications. + * Copyright (c) 1998-1999 TiVo, Inc. + * PowerPC 403GCX modifications. + * Copyright (c) 1999 Grant Erickson <grant@lcse.umn.edu> + * PowerPC 403GCX/405GP modifications. + * Copyright 2000 MontaVista Software Inc. + * PPC405 modifications + * PowerPC 403GCX/405GP modifications. + * Author: MontaVista Software, Inc. + * frank_rowand@mvista.com or source@mvista.com + * debbie_chu@mvista.com + * + * + * Module name: head_4xx.S + * + * Description: + * Kernel execution entry point code. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + */ + +#include <asm/processor.h> +#include <asm/page.h> +#include <asm/mmu.h> +#include <asm/pgtable.h> +#include <asm/ibm4xx.h> +#include <asm/cputable.h> +#include <asm/thread_info.h> +#include <asm/ppc_asm.h> +#include <asm/asm-offsets.h> + +/* As with the other PowerPC ports, it is expected that when code + * execution begins here, the following registers contain valid, yet + * optional, information: + * + * r3 - Board info structure pointer (DRAM, frequency, MAC address, etc.) + * r4 - Starting address of the init RAM disk + * r5 - Ending address of the init RAM disk + * r6 - Start of kernel command line string (e.g. "mem=96m") + * r7 - End of kernel command line string + * + * This is all going to change RSN when we add bi_recs....... -- Dan + */ + .text +_GLOBAL(_stext) +_GLOBAL(_start) + + /* Save parameters we are passed. + */ + mr r31,r3 + mr r30,r4 + mr r29,r5 + mr r28,r6 + mr r27,r7 + + /* We have to turn on the MMU right away so we get cache modes + * set correctly. + */ + bl initial_mmu + +/* We now have the lower 16 Meg mapped into TLB entries, and the caches + * ready to work. + */ +turn_on_mmu: + lis r0,MSR_KERNEL@h + ori r0,r0,MSR_KERNEL@l + mtspr SPRN_SRR1,r0 + lis r0,start_here@h + ori r0,r0,start_here@l + mtspr SPRN_SRR0,r0 + SYNC + rfi /* enables MMU */ + b . /* prevent prefetch past rfi */ + +/* + * This area is used for temporarily saving registers during the + * critical exception prolog. + */ + . = 0xc0 +crit_save: +_GLOBAL(crit_r10) + .space 4 +_GLOBAL(crit_r11) + .space 4 + +/* + * Exception vector entry code. This code runs with address translation + * turned off (i.e. using physical addresses). We assume SPRG3 has the + * physical address of the current task thread_struct. + * Note that we have to have decremented r1 before we write to any fields + * of the exception frame, since a critical interrupt could occur at any + * time, and it will write to the area immediately below the current r1. + */ +#define NORMAL_EXCEPTION_PROLOG \ + mtspr SPRN_SPRG0,r10; /* save two registers to work with */\ + mtspr SPRN_SPRG1,r11; \ + mtspr SPRN_SPRG2,r1; \ + mfcr r10; /* save CR in r10 for now */\ + mfspr r11,SPRN_SRR1; /* check whether user or kernel */\ + andi. r11,r11,MSR_PR; \ + beq 1f; \ + mfspr r1,SPRN_SPRG3; /* if from user, start at top of */\ + lwz r1,THREAD_INFO-THREAD(r1); /* this thread's kernel stack */\ + addi r1,r1,THREAD_SIZE; \ +1: subi r1,r1,INT_FRAME_SIZE; /* Allocate an exception frame */\ + tophys(r11,r1); \ + stw r10,_CCR(r11); /* save various registers */\ + stw r12,GPR12(r11); \ + stw r9,GPR9(r11); \ + mfspr r10,SPRN_SPRG0; \ + stw r10,GPR10(r11); \ + mfspr r12,SPRN_SPRG1; \ + stw r12,GPR11(r11); \ + mflr r10; \ + stw r10,_LINK(r11); \ + mfspr r10,SPRN_SPRG2; \ + mfspr r12,SPRN_SRR0; \ + stw r10,GPR1(r11); \ + mfspr r9,SPRN_SRR1; \ + stw r10,0(r11); \ + rlwinm r9,r9,0,14,12; /* clear MSR_WE (necessary?) */\ + stw r0,GPR0(r11); \ + SAVE_4GPRS(3, r11); \ + SAVE_2GPRS(7, r11) + +/* + * Exception prolog for critical exceptions. This is a little different + * from the normal exception prolog above since a critical exception + * can potentially occur at any point during normal exception processing. + * Thus we cannot use the same SPRG registers as the normal prolog above. + * Instead we use a couple of words of memory at low physical addresses. + * This is OK since we don't support SMP on these processors. + */ +#define CRITICAL_EXCEPTION_PROLOG \ + stw r10,crit_r10@l(0); /* save two registers to work with */\ + stw r11,crit_r11@l(0); \ + mfcr r10; /* save CR in r10 for now */\ + mfspr r11,SPRN_SRR3; /* check whether user or kernel */\ + andi. r11,r11,MSR_PR; \ + lis r11,critical_stack_top@h; \ + ori r11,r11,critical_stack_top@l; \ + beq 1f; \ + /* COMING FROM USER MODE */ \ + mfspr r11,SPRN_SPRG3; /* if from user, start at top of */\ + lwz r11,THREAD_INFO-THREAD(r11); /* this thread's kernel stack */\ + addi r11,r11,THREAD_SIZE; \ +1: subi r11,r11,INT_FRAME_SIZE; /* Allocate an exception frame */\ + tophys(r11,r11); \ + stw r10,_CCR(r11); /* save various registers */\ + stw r12,GPR12(r11); \ + stw r9,GPR9(r11); \ + mflr r10; \ + stw r10,_LINK(r11); \ + mfspr r12,SPRN_DEAR; /* save DEAR and ESR in the frame */\ + stw r12,_DEAR(r11); /* since they may have had stuff */\ + mfspr r9,SPRN_ESR; /* in them at the point where the */\ + stw r9,_ESR(r11); /* exception was taken */\ + mfspr r12,SPRN_SRR2; \ + stw r1,GPR1(r11); \ + mfspr r9,SPRN_SRR3; \ + stw r1,0(r11); \ + tovirt(r1,r11); \ + rlwinm r9,r9,0,14,12; /* clear MSR_WE (necessary?) */\ + stw r0,GPR0(r11); \ + SAVE_4GPRS(3, r11); \ + SAVE_2GPRS(7, r11) + + /* + * State at this point: + * r9 saved in stack frame, now saved SRR3 & ~MSR_WE + * r10 saved in crit_r10 and in stack frame, trashed + * r11 saved in crit_r11 and in stack frame, + * now phys stack/exception frame pointer + * r12 saved in stack frame, now saved SRR2 + * CR saved in stack frame, CR0.EQ = !SRR3.PR + * LR, DEAR, ESR in stack frame + * r1 saved in stack frame, now virt stack/excframe pointer + * r0, r3-r8 saved in stack frame + */ + +/* + * Exception vectors. + */ +#define START_EXCEPTION(n, label) \ + . = n; \ +label: + +#define EXCEPTION(n, label, hdlr, xfer) \ + START_EXCEPTION(n, label); \ + NORMAL_EXCEPTION_PROLOG; \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + xfer(n, hdlr) + +#define CRITICAL_EXCEPTION(n, label, hdlr) \ + START_EXCEPTION(n, label); \ + CRITICAL_EXCEPTION_PROLOG; \ + addi r3,r1,STACK_FRAME_OVERHEAD; \ + EXC_XFER_TEMPLATE(hdlr, n+2, (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), \ + NOCOPY, crit_transfer_to_handler, \ + ret_from_crit_exc) + +#define EXC_XFER_TEMPLATE(hdlr, trap, msr, copyee, tfer, ret) \ + li r10,trap; \ + stw r10,_TRAP(r11); \ + lis r10,msr@h; \ + ori r10,r10,msr@l; \ + copyee(r10, r9); \ + bl tfer; \ + .long hdlr; \ + .long ret + +#define COPY_EE(d, s) rlwimi d,s,0,16,16 +#define NOCOPY(d, s) + +#define EXC_XFER_STD(n, hdlr) \ + EXC_XFER_TEMPLATE(hdlr, n, MSR_KERNEL, NOCOPY, transfer_to_handler_full, \ + ret_from_except_full) + +#define EXC_XFER_LITE(n, hdlr) \ + EXC_XFER_TEMPLATE(hdlr, n+1, MSR_KERNEL, NOCOPY, transfer_to_handler, \ + ret_from_except) + +#define EXC_XFER_EE(n, hdlr) \ + EXC_XFER_TEMPLATE(hdlr, n, MSR_KERNEL, COPY_EE, transfer_to_handler_full, \ + ret_from_except_full) + +#define EXC_XFER_EE_LITE(n, hdlr) \ + EXC_XFER_TEMPLATE(hdlr, n+1, MSR_KERNEL, COPY_EE, transfer_to_handler, \ + ret_from_except) + + +/* + * 0x0100 - Critical Interrupt Exception + */ + CRITICAL_EXCEPTION(0x0100, CriticalInterrupt, unknown_exception) + +/* + * 0x0200 - Machine Check Exception + */ + CRITICAL_EXCEPTION(0x0200, MachineCheck, machine_check_exception) + +/* + * 0x0300 - Data Storage Exception + * This happens for just a few reasons. U0 set (but we don't do that), + * or zone protection fault (user violation, write to protected page). + * If this is just an update of modified status, we do that quickly + * and exit. Otherwise, we call heavywight functions to do the work. + */ + START_EXCEPTION(0x0300, DataStorage) + mtspr SPRN_SPRG0, r10 /* Save some working registers */ + mtspr SPRN_SPRG1, r11 +#ifdef CONFIG_403GCX + stw r12, 0(r0) + stw r9, 4(r0) + mfcr r11 + mfspr r12, SPRN_PID + stw r11, 8(r0) + stw r12, 12(r0) +#else + mtspr SPRN_SPRG4, r12 + mtspr SPRN_SPRG5, r9 + mfcr r11 + mfspr r12, SPRN_PID + mtspr SPRN_SPRG7, r11 + mtspr SPRN_SPRG6, r12 +#endif + + /* First, check if it was a zone fault (which means a user + * tried to access a kernel or read-protected page - always + * a SEGV). All other faults here must be stores, so no + * need to check ESR_DST as well. */ + mfspr r10, SPRN_ESR + andis. r10, r10, ESR_DIZ@h + bne 2f + + mfspr r10, SPRN_DEAR /* Get faulting address */ + + /* If we are faulting a kernel address, we have to use the + * kernel page tables. + */ + lis r11, TASK_SIZE@h + cmplw r10, r11 + blt+ 3f + lis r11, swapper_pg_dir@h + ori r11, r11, swapper_pg_dir@l + li r9, 0 + mtspr SPRN_PID, r9 /* TLB will have 0 TID */ + b 4f + + /* Get the PGD for the current thread. + */ +3: + mfspr r11,SPRN_SPRG3 + lwz r11,PGDIR(r11) +4: + tophys(r11, r11) + rlwimi r11, r10, 12, 20, 29 /* Create L1 (pgdir/pmd) address */ + lwz r11, 0(r11) /* Get L1 entry */ + rlwinm. r12, r11, 0, 0, 19 /* Extract L2 (pte) base address */ + beq 2f /* Bail if no table */ + + rlwimi r12, r10, 22, 20, 29 /* Compute PTE address */ + lwz r11, 0(r12) /* Get Linux PTE */ + + andi. r9, r11, _PAGE_RW /* Is it writeable? */ + beq 2f /* Bail if not */ + + /* Update 'changed'. + */ + ori r11, r11, _PAGE_DIRTY|_PAGE_ACCESSED|_PAGE_HWWRITE + stw r11, 0(r12) /* Update Linux page table */ + + /* Most of the Linux PTE is ready to load into the TLB LO. + * We set ZSEL, where only the LS-bit determines user access. + * We set execute, because we don't have the granularity to + * properly set this at the page level (Linux problem). + * If shared is set, we cause a zero PID->TID load. + * Many of these bits are software only. Bits we don't set + * here we (properly should) assume have the appropriate value. + */ + li r12, 0x0ce2 + andc r11, r11, r12 /* Make sure 20, 21 are zero */ + + /* find the TLB index that caused the fault. It has to be here. + */ + tlbsx r9, 0, r10 + + tlbwe r11, r9, TLB_DATA /* Load TLB LO */ + + /* Done...restore registers and get out of here. + */ +#ifdef CONFIG_403GCX + lwz r12, 12(r0) + lwz r11, 8(r0) + mtspr SPRN_PID, r12 + mtcr r11 + lwz r9, 4(r0) + lwz r12, 0(r0) +#else + mfspr r12, SPRN_SPRG6 + mfspr r11, SPRN_SPRG7 + mtspr SPRN_PID, r12 + mtcr r11 + mfspr r9, SPRN_SPRG5 + mfspr r12, SPRN_SPRG4 +#endif + mfspr r11, SPRN_SPRG1 + mfspr r10, SPRN_SPRG0 + PPC405_ERR77_SYNC + rfi /* Should sync shadow TLBs */ + b . /* prevent prefetch past rfi */ + +2: + /* The bailout. Restore registers to pre-exception conditions + * and call the heavyweights to help us out. + */ +#ifdef CONFIG_403GCX + lwz r12, 12(r0) + lwz r11, 8(r0) + mtspr SPRN_PID, r12 + mtcr r11 + lwz r9, 4(r0) + lwz r12, 0(r0) +#else + mfspr r12, SPRN_SPRG6 + mfspr r11, SPRN_SPRG7 + mtspr SPRN_PID, r12 + mtcr r11 + mfspr r9, SPRN_SPRG5 + mfspr r12, SPRN_SPRG4 +#endif + mfspr r11, SPRN_SPRG1 + mfspr r10, SPRN_SPRG0 + b DataAccess + +/* + * 0x0400 - Instruction Storage Exception + * This is caused by a fetch from non-execute or guarded pages. + */ + START_EXCEPTION(0x0400, InstructionAccess) + NORMAL_EXCEPTION_PROLOG + mr r4,r12 /* Pass SRR0 as arg2 */ + li r5,0 /* Pass zero as arg3 */ + EXC_XFER_EE_LITE(0x400, handle_page_fault) + +/* 0x0500 - External Interrupt Exception */ + EXCEPTION(0x0500, HardwareInterrupt, do_IRQ, EXC_XFER_LITE) + +/* 0x0600 - Alignment Exception */ + START_EXCEPTION(0x0600, Alignment) + NORMAL_EXCEPTION_PROLOG + mfspr r4,SPRN_DEAR /* Grab the DEAR and save it */ + stw r4,_DEAR(r11) + addi r3,r1,STACK_FRAME_OVERHEAD + EXC_XFER_EE(0x600, alignment_exception) + +/* 0x0700 - Program Exception */ + START_EXCEPTION(0x0700, ProgramCheck) + NORMAL_EXCEPTION_PROLOG + mfspr r4,SPRN_ESR /* Grab the ESR and save it */ + stw r4,_ESR(r11) + addi r3,r1,STACK_FRAME_OVERHEAD + EXC_XFER_STD(0x700, program_check_exception) + + EXCEPTION(0x0800, Trap_08, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x0900, Trap_09, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x0A00, Trap_0A, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x0B00, Trap_0B, unknown_exception, EXC_XFER_EE) + +/* 0x0C00 - System Call Exception */ + START_EXCEPTION(0x0C00, SystemCall) + NORMAL_EXCEPTION_PROLOG + EXC_XFER_EE_LITE(0xc00, DoSyscall) + + EXCEPTION(0x0D00, Trap_0D, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x0E00, Trap_0E, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x0F00, Trap_0F, unknown_exception, EXC_XFER_EE) + +/* 0x1000 - Programmable Interval Timer (PIT) Exception */ + START_EXCEPTION(0x1000, Decrementer) + NORMAL_EXCEPTION_PROLOG + lis r0,TSR_PIS@h + mtspr SPRN_TSR,r0 /* Clear the PIT exception */ + addi r3,r1,STACK_FRAME_OVERHEAD + EXC_XFER_LITE(0x1000, timer_interrupt) + +#if 0 +/* NOTE: + * FIT and WDT handlers are not implemented yet. + */ + +/* 0x1010 - Fixed Interval Timer (FIT) Exception +*/ + STND_EXCEPTION(0x1010, FITException, unknown_exception) + +/* 0x1020 - Watchdog Timer (WDT) Exception +*/ +#ifdef CONFIG_BOOKE_WDT + CRITICAL_EXCEPTION(0x1020, WDTException, WatchdogException) +#else + CRITICAL_EXCEPTION(0x1020, WDTException, unknown_exception) +#endif +#endif + +/* 0x1100 - Data TLB Miss Exception + * As the name implies, translation is not in the MMU, so search the + * page tables and fix it. The only purpose of this function is to + * load TLB entries from the page table if they exist. + */ + START_EXCEPTION(0x1100, DTLBMiss) + mtspr SPRN_SPRG0, r10 /* Save some working registers */ + mtspr SPRN_SPRG1, r11 +#ifdef CONFIG_403GCX + stw r12, 0(r0) + stw r9, 4(r0) + mfcr r11 + mfspr r12, SPRN_PID + stw r11, 8(r0) + stw r12, 12(r0) +#else + mtspr SPRN_SPRG4, r12 + mtspr SPRN_SPRG5, r9 + mfcr r11 + mfspr r12, SPRN_PID + mtspr SPRN_SPRG7, r11 + mtspr SPRN_SPRG6, r12 +#endif + mfspr r10, SPRN_DEAR /* Get faulting address */ + + /* If we are faulting a kernel address, we have to use the + * kernel page tables. + */ + lis r11, TASK_SIZE@h + cmplw r10, r11 + blt+ 3f + lis r11, swapper_pg_dir@h + ori r11, r11, swapper_pg_dir@l + li r9, 0 + mtspr SPRN_PID, r9 /* TLB will have 0 TID */ + b 4f + + /* Get the PGD for the current thread. + */ +3: + mfspr r11,SPRN_SPRG3 + lwz r11,PGDIR(r11) +4: + tophys(r11, r11) + rlwimi r11, r10, 12, 20, 29 /* Create L1 (pgdir/pmd) address */ + lwz r12, 0(r11) /* Get L1 entry */ + andi. r9, r12, _PMD_PRESENT /* Check if it points to a PTE page */ + beq 2f /* Bail if no table */ + + rlwimi r12, r10, 22, 20, 29 /* Compute PTE address */ + lwz r11, 0(r12) /* Get Linux PTE */ + andi. r9, r11, _PAGE_PRESENT + beq 5f + + ori r11, r11, _PAGE_ACCESSED + stw r11, 0(r12) + + /* Create TLB tag. This is the faulting address plus a static + * set of bits. These are size, valid, E, U0. + */ + li r12, 0x00c0 + rlwimi r10, r12, 0, 20, 31 + + b finish_tlb_load + +2: /* Check for possible large-page pmd entry */ + rlwinm. r9, r12, 2, 22, 24 + beq 5f + + /* Create TLB tag. This is the faulting address, plus a static + * set of bits (valid, E, U0) plus the size from the PMD. + */ + ori r9, r9, 0x40 + rlwimi r10, r9, 0, 20, 31 + mr r11, r12 + + b finish_tlb_load + +5: + /* The bailout. Restore registers to pre-exception conditions + * and call the heavyweights to help us out. + */ +#ifdef CONFIG_403GCX + lwz r12, 12(r0) + lwz r11, 8(r0) + mtspr SPRN_PID, r12 + mtcr r11 + lwz r9, 4(r0) + lwz r12, 0(r0) +#else + mfspr r12, SPRN_SPRG6 + mfspr r11, SPRN_SPRG7 + mtspr SPRN_PID, r12 + mtcr r11 + mfspr r9, SPRN_SPRG5 + mfspr r12, SPRN_SPRG4 +#endif + mfspr r11, SPRN_SPRG1 + mfspr r10, SPRN_SPRG0 + b DataAccess + +/* 0x1200 - Instruction TLB Miss Exception + * Nearly the same as above, except we get our information from different + * registers and bailout to a different point. + */ + START_EXCEPTION(0x1200, ITLBMiss) + mtspr SPRN_SPRG0, r10 /* Save some working registers */ + mtspr SPRN_SPRG1, r11 +#ifdef CONFIG_403GCX + stw r12, 0(r0) + stw r9, 4(r0) + mfcr r11 + mfspr r12, SPRN_PID + stw r11, 8(r0) + stw r12, 12(r0) +#else + mtspr SPRN_SPRG4, r12 + mtspr SPRN_SPRG5, r9 + mfcr r11 + mfspr r12, SPRN_PID + mtspr SPRN_SPRG7, r11 + mtspr SPRN_SPRG6, r12 +#endif + mfspr r10, SPRN_SRR0 /* Get faulting address */ + + /* If we are faulting a kernel address, we have to use the + * kernel page tables. + */ + lis r11, TASK_SIZE@h + cmplw r10, r11 + blt+ 3f + lis r11, swapper_pg_dir@h + ori r11, r11, swapper_pg_dir@l + li r9, 0 + mtspr SPRN_PID, r9 /* TLB will have 0 TID */ + b 4f + + /* Get the PGD for the current thread. + */ +3: + mfspr r11,SPRN_SPRG3 + lwz r11,PGDIR(r11) +4: + tophys(r11, r11) + rlwimi r11, r10, 12, 20, 29 /* Create L1 (pgdir/pmd) address */ + lwz r12, 0(r11) /* Get L1 entry */ + andi. r9, r12, _PMD_PRESENT /* Check if it points to a PTE page */ + beq 2f /* Bail if no table */ + + rlwimi r12, r10, 22, 20, 29 /* Compute PTE address */ + lwz r11, 0(r12) /* Get Linux PTE */ + andi. r9, r11, _PAGE_PRESENT + beq 5f + + ori r11, r11, _PAGE_ACCESSED + stw r11, 0(r12) + + /* Create TLB tag. This is the faulting address plus a static + * set of bits. These are size, valid, E, U0. + */ + li r12, 0x00c0 + rlwimi r10, r12, 0, 20, 31 + + b finish_tlb_load + +2: /* Check for possible large-page pmd entry */ + rlwinm. r9, r12, 2, 22, 24 + beq 5f + + /* Create TLB tag. This is the faulting address, plus a static + * set of bits (valid, E, U0) plus the size from the PMD. + */ + ori r9, r9, 0x40 + rlwimi r10, r9, 0, 20, 31 + mr r11, r12 + + b finish_tlb_load + +5: + /* The bailout. Restore registers to pre-exception conditions + * and call the heavyweights to help us out. + */ +#ifdef CONFIG_403GCX + lwz r12, 12(r0) + lwz r11, 8(r0) + mtspr SPRN_PID, r12 + mtcr r11 + lwz r9, 4(r0) + lwz r12, 0(r0) +#else + mfspr r12, SPRN_SPRG6 + mfspr r11, SPRN_SPRG7 + mtspr SPRN_PID, r12 + mtcr r11 + mfspr r9, SPRN_SPRG5 + mfspr r12, SPRN_SPRG4 +#endif + mfspr r11, SPRN_SPRG1 + mfspr r10, SPRN_SPRG0 + b InstructionAccess + + EXCEPTION(0x1300, Trap_13, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1400, Trap_14, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1500, Trap_15, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1600, Trap_16, unknown_exception, EXC_XFER_EE) +#ifdef CONFIG_IBM405_ERR51 + /* 405GP errata 51 */ + START_EXCEPTION(0x1700, Trap_17) + b DTLBMiss +#else + EXCEPTION(0x1700, Trap_17, unknown_exception, EXC_XFER_EE) +#endif + EXCEPTION(0x1800, Trap_18, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1900, Trap_19, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1A00, Trap_1A, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1B00, Trap_1B, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1C00, Trap_1C, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1D00, Trap_1D, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1E00, Trap_1E, unknown_exception, EXC_XFER_EE) + EXCEPTION(0x1F00, Trap_1F, unknown_exception, EXC_XFER_EE) + +/* Check for a single step debug exception while in an exception + * handler before state has been saved. This is to catch the case + * where an instruction that we are trying to single step causes + * an exception (eg ITLB/DTLB miss) and thus the first instruction of + * the exception handler generates a single step debug exception. + * + * If we get a debug trap on the first instruction of an exception handler, + * we reset the MSR_DE in the _exception handler's_ MSR (the debug trap is + * a critical exception, so we are using SPRN_CSRR1 to manipulate the MSR). + * The exception handler was handling a non-critical interrupt, so it will + * save (and later restore) the MSR via SPRN_SRR1, which will still have + * the MSR_DE bit set. + */ + /* 0x2000 - Debug Exception */ + START_EXCEPTION(0x2000, DebugTrap) + CRITICAL_EXCEPTION_PROLOG + + /* + * If this is a single step or branch-taken exception in an + * exception entry sequence, it was probably meant to apply to + * the code where the exception occurred (since exception entry + * doesn't turn off DE automatically). We simulate the effect + * of turning off DE on entry to an exception handler by turning + * off DE in the SRR3 value and clearing the debug status. + */ + mfspr r10,SPRN_DBSR /* check single-step/branch taken */ + andis. r10,r10,DBSR_IC@h + beq+ 2f + + andi. r10,r9,MSR_IR|MSR_PR /* check supervisor + MMU off */ + beq 1f /* branch and fix it up */ + + mfspr r10,SPRN_SRR2 /* Faulting instruction address */ + cmplwi r10,0x2100 + bgt+ 2f /* address above exception vectors */ + + /* here it looks like we got an inappropriate debug exception. */ +1: rlwinm r9,r9,0,~MSR_DE /* clear DE in the SRR3 value */ + lis r10,DBSR_IC@h /* clear the IC event */ + mtspr SPRN_DBSR,r10 + /* restore state and get out */ + lwz r10,_CCR(r11) + lwz r0,GPR0(r11) + lwz r1,GPR1(r11) + mtcrf 0x80,r10 + mtspr SPRN_SRR2,r12 + mtspr SPRN_SRR3,r9 + lwz r9,GPR9(r11) + lwz r12,GPR12(r11) + lwz r10,crit_r10@l(0) + lwz r11,crit_r11@l(0) + PPC405_ERR77_SYNC + rfci + b . + + /* continue normal handling for a critical exception... */ +2: mfspr r4,SPRN_DBSR + addi r3,r1,STACK_FRAME_OVERHEAD + EXC_XFER_TEMPLATE(DebugException, 0x2002, \ + (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), \ + NOCOPY, crit_transfer_to_handler, ret_from_crit_exc) + +/* + * The other Data TLB exceptions bail out to this point + * if they can't resolve the lightweight TLB fault. + */ +DataAccess: + NORMAL_EXCEPTION_PROLOG + mfspr r5,SPRN_ESR /* Grab the ESR, save it, pass arg3 */ + stw r5,_ESR(r11) + mfspr r4,SPRN_DEAR /* Grab the DEAR, save it, pass arg2 */ + EXC_XFER_EE_LITE(0x300, handle_page_fault) + +/* Other PowerPC processors, namely those derived from the 6xx-series + * have vectors from 0x2100 through 0x2F00 defined, but marked as reserved. + * However, for the 4xx-series processors these are neither defined nor + * reserved. + */ + + /* Damn, I came up one instruction too many to fit into the + * exception space :-). Both the instruction and data TLB + * miss get to this point to load the TLB. + * r10 - TLB_TAG value + * r11 - Linux PTE + * r12, r9 - avilable to use + * PID - loaded with proper value when we get here + * Upon exit, we reload everything and RFI. + * Actually, it will fit now, but oh well.....a common place + * to load the TLB. + */ +tlb_4xx_index: + .long 0 +finish_tlb_load: + /* load the next available TLB index. + */ + lwz r9, tlb_4xx_index@l(0) + addi r9, r9, 1 + andi. r9, r9, (PPC4XX_TLB_SIZE-1) + stw r9, tlb_4xx_index@l(0) + +6: + /* + * Clear out the software-only bits in the PTE to generate the + * TLB_DATA value. These are the bottom 2 bits of the RPM, the + * top 3 bits of the zone field, and M. + */ + li r12, 0x0ce2 + andc r11, r11, r12 + + tlbwe r11, r9, TLB_DATA /* Load TLB LO */ + tlbwe r10, r9, TLB_TAG /* Load TLB HI */ + + /* Done...restore registers and get out of here. + */ +#ifdef CONFIG_403GCX + lwz r12, 12(r0) + lwz r11, 8(r0) + mtspr SPRN_PID, r12 + mtcr r11 + lwz r9, 4(r0) + lwz r12, 0(r0) +#else + mfspr r12, SPRN_SPRG6 + mfspr r11, SPRN_SPRG7 + mtspr SPRN_PID, r12 + mtcr r11 + mfspr r9, SPRN_SPRG5 + mfspr r12, SPRN_SPRG4 +#endif + mfspr r11, SPRN_SPRG1 + mfspr r10, SPRN_SPRG0 + PPC405_ERR77_SYNC + rfi /* Should sync shadow TLBs */ + b . /* prevent prefetch past rfi */ + +/* extern void giveup_fpu(struct task_struct *prev) + * + * The PowerPC 4xx family of processors do not have an FPU, so this just + * returns. + */ +_GLOBAL(giveup_fpu) + blr + +/* This is where the main kernel code starts. + */ +start_here: + + /* ptr to current */ + lis r2,init_task@h + ori r2,r2,init_task@l + + /* ptr to phys current thread */ + tophys(r4,r2) + addi r4,r4,THREAD /* init task's THREAD */ + mtspr SPRN_SPRG3,r4 + + /* stack */ + lis r1,init_thread_union@ha + addi r1,r1,init_thread_union@l + li r0,0 + stwu r0,THREAD_SIZE-STACK_FRAME_OVERHEAD(r1) + + bl early_init /* We have to do this with MMU on */ + +/* + * Decide what sort of machine this is and initialize the MMU. + */ + mr r3,r31 + mr r4,r30 + mr r5,r29 + mr r6,r28 + mr r7,r27 + bl machine_init + bl MMU_init + +/* Go back to running unmapped so we can load up new values + * and change to using our exception vectors. + * On the 4xx, all we have to do is invalidate the TLB to clear + * the old 16M byte TLB mappings. + */ + lis r4,2f@h + ori r4,r4,2f@l + tophys(r4,r4) + lis r3,(MSR_KERNEL & ~(MSR_IR|MSR_DR))@h + ori r3,r3,(MSR_KERNEL & ~(MSR_IR|MSR_DR))@l + mtspr SPRN_SRR0,r4 + mtspr SPRN_SRR1,r3 + rfi + b . /* prevent prefetch past rfi */ + +/* Load up the kernel context */ +2: + sync /* Flush to memory before changing TLB */ + tlbia + isync /* Flush shadow TLBs */ + + /* set up the PTE pointers for the Abatron bdiGDB. + */ + lis r6, swapper_pg_dir@h + ori r6, r6, swapper_pg_dir@l + lis r5, abatron_pteptrs@h + ori r5, r5, abatron_pteptrs@l + stw r5, 0xf0(r0) /* Must match your Abatron config file */ + tophys(r5,r5) + stw r6, 0(r5) + +/* Now turn on the MMU for real! */ + lis r4,MSR_KERNEL@h + ori r4,r4,MSR_KERNEL@l + lis r3,start_kernel@h + ori r3,r3,start_kernel@l + mtspr SPRN_SRR0,r3 + mtspr SPRN_SRR1,r4 + rfi /* enable MMU and jump to start_kernel */ + b . /* prevent prefetch past rfi */ + +/* Set up the initial MMU state so we can do the first level of + * kernel initialization. This maps the first 16 MBytes of memory 1:1 + * virtual to physical and more importantly sets the cache mode. + */ +initial_mmu: + tlbia /* Invalidate all TLB entries */ + isync + + /* We should still be executing code at physical address 0x0000xxxx + * at this point. However, start_here is at virtual address + * 0xC000xxxx. So, set up a TLB mapping to cover this once + * translation is enabled. + */ + + lis r3,KERNELBASE@h /* Load the kernel virtual address */ + ori r3,r3,KERNELBASE@l + tophys(r4,r3) /* Load the kernel physical address */ + + iccci r0,r3 /* Invalidate the i-cache before use */ + + /* Load the kernel PID. + */ + li r0,0 + mtspr SPRN_PID,r0 + sync + + /* Configure and load two entries into TLB slots 62 and 63. + * In case we are pinning TLBs, these are reserved in by the + * other TLB functions. If not reserving, then it doesn't + * matter where they are loaded. + */ + clrrwi r4,r4,10 /* Mask off the real page number */ + ori r4,r4,(TLB_WR | TLB_EX) /* Set the write and execute bits */ + + clrrwi r3,r3,10 /* Mask off the effective page number */ + ori r3,r3,(TLB_VALID | TLB_PAGESZ(PAGESZ_16M)) + + li r0,63 /* TLB slot 63 */ + + tlbwe r4,r0,TLB_DATA /* Load the data portion of the entry */ + tlbwe r3,r0,TLB_TAG /* Load the tag portion of the entry */ + +#if defined(CONFIG_SERIAL_TEXT_DEBUG) && defined(SERIAL_DEBUG_IO_BASE) + + /* Load a TLB entry for the UART, so that ppc4xx_progress() can use + * the UARTs nice and early. We use a 4k real==virtual mapping. */ + + lis r3,SERIAL_DEBUG_IO_BASE@h + ori r3,r3,SERIAL_DEBUG_IO_BASE@l + mr r4,r3 + clrrwi r4,r4,12 + ori r4,r4,(TLB_WR|TLB_I|TLB_M|TLB_G) + + clrrwi r3,r3,12 + ori r3,r3,(TLB_VALID | TLB_PAGESZ(PAGESZ_4K)) + + li r0,0 /* TLB slot 0 */ + tlbwe r4,r0,TLB_DATA + tlbwe r3,r0,TLB_TAG +#endif /* CONFIG_SERIAL_DEBUG_TEXT && SERIAL_DEBUG_IO_BASE */ + + isync + + /* Establish the exception vector base + */ + lis r4,KERNELBASE@h /* EVPR only uses the high 16-bits */ + tophys(r0,r4) /* Use the physical address */ + mtspr SPRN_EVPR,r0 + + blr + +_GLOBAL(abort) + mfspr r13,SPRN_DBCR0 + oris r13,r13,DBCR0_RST_SYSTEM@h + mtspr SPRN_DBCR0,r13 + +_GLOBAL(set_context) + +#ifdef CONFIG_BDI_SWITCH + /* Context switch the PTE pointer for the Abatron BDI2000. + * The PGDIR is the second parameter. + */ + lis r5, KERNELBASE@h + lwz r5, 0xf0(r5) + stw r4, 0x4(r5) +#endif + sync + mtspr SPRN_PID,r3 + isync /* Need an isync to flush shadow */ + /* TLBs after changing PID */ + blr + +/* We put a few things here that have to be page-aligned. This stuff + * goes at the beginning of the data segment, which is page-aligned. + */ + .data + .align 12 + .globl sdata +sdata: + .globl empty_zero_page +empty_zero_page: + .space 4096 + .globl swapper_pg_dir +swapper_pg_dir: + .space 4096 + + +/* Stack for handling critical exceptions from kernel mode */ + .section .bss + .align 12 +exception_stack_bottom: + .space 4096 +critical_stack_top: + .globl exception_stack_top +exception_stack_top: + +/* This space gets a copy of optional info passed to us by the bootstrap + * which is used to pass parameters into the kernel like root=/dev/sda1, etc. + */ + .globl cmd_line +cmd_line: + .space 512 + +/* Room for two PTE pointers, usually the kernel and current user pointers + * to their respective root page table. + */ +abatron_pteptrs: + .space 8 --- linux-2.6.orig/arch/powerpc/kernel/head_4xx.S +++ /dev/null @@ -1,1021 +0,0 @@ -/* - * Copyright (c) 1995-1996 Gary Thomas <gdt@linuxppc.org> - * Initial PowerPC version. - * Copyright (c) 1996 Cort Dougan <cort@cs.nmt.edu> - * Rewritten for PReP - * Copyright (c) 1996 Paul Mackerras <paulus@cs.anu.edu.au> - * Low-level exception handers, MMU support, and rewrite. - * Copyright (c) 1997 Dan Malek <dmalek@jlc.net> - * PowerPC 8xx modifications. - * Copyright (c) 1998-1999 TiVo, Inc. - * PowerPC 403GCX modifications. - * Copyright (c) 1999 Grant Erickson <grant@lcse.umn.edu> - * PowerPC 403GCX/405GP modifications. - * Copyright 2000 MontaVista Software Inc. - * PPC405 modifications - * PowerPC 403GCX/405GP modifications. - * Author: MontaVista Software, Inc. - * frank_rowand@mvista.com or source@mvista.com - * debbie_chu@mvista.com - * - * - * Module name: head_4xx.S - * - * Description: - * Kernel execution entry point code. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. - * - */ - -#include <asm/processor.h> -#include <asm/page.h> -#include <asm/mmu.h> -#include <asm/pgtable.h> -#include <asm/ibm4xx.h> -#include <asm/cputable.h> -#include <asm/thread_info.h> -#include <asm/ppc_asm.h> -#include <asm/asm-offsets.h> - -/* As with the other PowerPC ports, it is expected that when code - * execution begins here, the following registers contain valid, yet - * optional, information: - * - * r3 - Board info structure pointer (DRAM, frequency, MAC address, etc.) - * r4 - Starting address of the init RAM disk - * r5 - Ending address of the init RAM disk - * r6 - Start of kernel command line string (e.g. "mem=96m") - * r7 - End of kernel command line string - * - * This is all going to change RSN when we add bi_recs....... -- Dan - */ - .text -_GLOBAL(_stext) -_GLOBAL(_start) - - /* Save parameters we are passed. - */ - mr r31,r3 - mr r30,r4 - mr r29,r5 - mr r28,r6 - mr r27,r7 - - /* We have to turn on the MMU right away so we get cache modes - * set correctly. - */ - bl initial_mmu - -/* We now have the lower 16 Meg mapped into TLB entries, and the caches - * ready to work. - */ -turn_on_mmu: - lis r0,MSR_KERNEL@h - ori r0,r0,MSR_KERNEL@l - mtspr SPRN_SRR1,r0 - lis r0,start_here@h - ori r0,r0,start_here@l - mtspr SPRN_SRR0,r0 - SYNC - rfi /* enables MMU */ - b . /* prevent prefetch past rfi */ - -/* - * This area is used for temporarily saving registers during the - * critical exception prolog. - */ - . = 0xc0 -crit_save: -_GLOBAL(crit_r10) - .space 4 -_GLOBAL(crit_r11) - .space 4 - -/* - * Exception vector entry code. This code runs with address translation - * turned off (i.e. using physical addresses). We assume SPRG3 has the - * physical address of the current task thread_struct. - * Note that we have to have decremented r1 before we write to any fields - * of the exception frame, since a critical interrupt could occur at any - * time, and it will write to the area immediately below the current r1. - */ -#define NORMAL_EXCEPTION_PROLOG \ - mtspr SPRN_SPRG0,r10; /* save two registers to work with */\ - mtspr SPRN_SPRG1,r11; \ - mtspr SPRN_SPRG2,r1; \ - mfcr r10; /* save CR in r10 for now */\ - mfspr r11,SPRN_SRR1; /* check whether user or kernel */\ - andi. r11,r11,MSR_PR; \ - beq 1f; \ - mfspr r1,SPRN_SPRG3; /* if from user, start at top of */\ - lwz r1,THREAD_INFO-THREAD(r1); /* this thread's kernel stack */\ - addi r1,r1,THREAD_SIZE; \ -1: subi r1,r1,INT_FRAME_SIZE; /* Allocate an exception frame */\ - tophys(r11,r1); \ - stw r10,_CCR(r11); /* save various registers */\ - stw r12,GPR12(r11); \ - stw r9,GPR9(r11); \ - mfspr r10,SPRN_SPRG0; \ - stw r10,GPR10(r11); \ - mfspr r12,SPRN_SPRG1; \ - stw r12,GPR11(r11); \ - mflr r10; \ - stw r10,_LINK(r11); \ - mfspr r10,SPRN_SPRG2; \ - mfspr r12,SPRN_SRR0; \ - stw r10,GPR1(r11); \ - mfspr r9,SPRN_SRR1; \ - stw r10,0(r11); \ - rlwinm r9,r9,0,14,12; /* clear MSR_WE (necessary?) */\ - stw r0,GPR0(r11); \ - SAVE_4GPRS(3, r11); \ - SAVE_2GPRS(7, r11) - -/* - * Exception prolog for critical exceptions. This is a little different - * from the normal exception prolog above since a critical exception - * can potentially occur at any point during normal exception processing. - * Thus we cannot use the same SPRG registers as the normal prolog above. - * Instead we use a couple of words of memory at low physical addresses. - * This is OK since we don't support SMP on these processors. - */ -#define CRITICAL_EXCEPTION_PROLOG \ - stw r10,crit_r10@l(0); /* save two registers to work with */\ - stw r11,crit_r11@l(0); \ - mfcr r10; /* save CR in r10 for now */\ - mfspr r11,SPRN_SRR3; /* check whether user or kernel */\ - andi. r11,r11,MSR_PR; \ - lis r11,critical_stack_top@h; \ - ori r11,r11,critical_stack_top@l; \ - beq 1f; \ - /* COMING FROM USER MODE */ \ - mfspr r11,SPRN_SPRG3; /* if from user, start at top of */\ - lwz r11,THREAD_INFO-THREAD(r11); /* this thread's kernel stack */\ - addi r11,r11,THREAD_SIZE; \ -1: subi r11,r11,INT_FRAME_SIZE; /* Allocate an exception frame */\ - tophys(r11,r11); \ - stw r10,_CCR(r11); /* save various registers */\ - stw r12,GPR12(r11); \ - stw r9,GPR9(r11); \ - mflr r10; \ - stw r10,_LINK(r11); \ - mfspr r12,SPRN_DEAR; /* save DEAR and ESR in the frame */\ - stw r12,_DEAR(r11); /* since they may have had stuff */\ - mfspr r9,SPRN_ESR; /* in them at the point where the */\ - stw r9,_ESR(r11); /* exception was taken */\ - mfspr r12,SPRN_SRR2; \ - stw r1,GPR1(r11); \ - mfspr r9,SPRN_SRR3; \ - stw r1,0(r11); \ - tovirt(r1,r11); \ - rlwinm r9,r9,0,14,12; /* clear MSR_WE (necessary?) */\ - stw r0,GPR0(r11); \ - SAVE_4GPRS(3, r11); \ - SAVE_2GPRS(7, r11) - - /* - * State at this point: - * r9 saved in stack frame, now saved SRR3 & ~MSR_WE - * r10 saved in crit_r10 and in stack frame, trashed - * r11 saved in crit_r11 and in stack frame, - * now phys stack/exception frame pointer - * r12 saved in stack frame, now saved SRR2 - * CR saved in stack frame, CR0.EQ = !SRR3.PR - * LR, DEAR, ESR in stack frame - * r1 saved in stack frame, now virt stack/excframe pointer - * r0, r3-r8 saved in stack frame - */ - -/* - * Exception vectors. - */ -#define START_EXCEPTION(n, label) \ - . = n; \ -label: - -#define EXCEPTION(n, label, hdlr, xfer) \ - START_EXCEPTION(n, label); \ - NORMAL_EXCEPTION_PROLOG; \ - addi r3,r1,STACK_FRAME_OVERHEAD; \ - xfer(n, hdlr) - -#define CRITICAL_EXCEPTION(n, label, hdlr) \ - START_EXCEPTION(n, label); \ - CRITICAL_EXCEPTION_PROLOG; \ - addi r3,r1,STACK_FRAME_OVERHEAD; \ - EXC_XFER_TEMPLATE(hdlr, n+2, (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), \ - NOCOPY, crit_transfer_to_handler, \ - ret_from_crit_exc) - -#define EXC_XFER_TEMPLATE(hdlr, trap, msr, copyee, tfer, ret) \ - li r10,trap; \ - stw r10,_TRAP(r11); \ - lis r10,msr@h; \ - ori r10,r10,msr@l; \ - copyee(r10, r9); \ - bl tfer; \ - .long hdlr; \ - .long ret - -#define COPY_EE(d, s) rlwimi d,s,0,16,16 -#define NOCOPY(d, s) - -#define EXC_XFER_STD(n, hdlr) \ - EXC_XFER_TEMPLATE(hdlr, n, MSR_KERNEL, NOCOPY, transfer_to_handler_full, \ - ret_from_except_full) - -#define EXC_XFER_LITE(n, hdlr) \ - EXC_XFER_TEMPLATE(hdlr, n+1, MSR_KERNEL, NOCOPY, transfer_to_handler, \ - ret_from_except) - -#define EXC_XFER_EE(n, hdlr) \ - EXC_XFER_TEMPLATE(hdlr, n, MSR_KERNEL, COPY_EE, transfer_to_handler_full, \ - ret_from_except_full) - -#define EXC_XFER_EE_LITE(n, hdlr) \ - EXC_XFER_TEMPLATE(hdlr, n+1, MSR_KERNEL, COPY_EE, transfer_to_handler, \ - ret_from_except) - - -/* - * 0x0100 - Critical Interrupt Exception - */ - CRITICAL_EXCEPTION(0x0100, CriticalInterrupt, unknown_exception) - -/* - * 0x0200 - Machine Check Exception - */ - CRITICAL_EXCEPTION(0x0200, MachineCheck, machine_check_exception) - -/* - * 0x0300 - Data Storage Exception - * This happens for just a few reasons. U0 set (but we don't do that), - * or zone protection fault (user violation, write to protected page). - * If this is just an update of modified status, we do that quickly - * and exit. Otherwise, we call heavywight functions to do the work. - */ - START_EXCEPTION(0x0300, DataStorage) - mtspr SPRN_SPRG0, r10 /* Save some working registers */ - mtspr SPRN_SPRG1, r11 -#ifdef CONFIG_403GCX - stw r12, 0(r0) - stw r9, 4(r0) - mfcr r11 - mfspr r12, SPRN_PID - stw r11, 8(r0) - stw r12, 12(r0) -#else - mtspr SPRN_SPRG4, r12 - mtspr SPRN_SPRG5, r9 - mfcr r11 - mfspr r12, SPRN_PID - mtspr SPRN_SPRG7, r11 - mtspr SPRN_SPRG6, r12 -#endif - - /* First, check if it was a zone fault (which means a user - * tried to access a kernel or read-protected page - always - * a SEGV). All other faults here must be stores, so no - * need to check ESR_DST as well. */ - mfspr r10, SPRN_ESR - andis. r10, r10, ESR_DIZ@h - bne 2f - - mfspr r10, SPRN_DEAR /* Get faulting address */ - - /* If we are faulting a kernel address, we have to use the - * kernel page tables. - */ - lis r11, TASK_SIZE@h - cmplw r10, r11 - blt+ 3f - lis r11, swapper_pg_dir@h - ori r11, r11, swapper_pg_dir@l - li r9, 0 - mtspr SPRN_PID, r9 /* TLB will have 0 TID */ - b 4f - - /* Get the PGD for the current thread. - */ -3: - mfspr r11,SPRN_SPRG3 - lwz r11,PGDIR(r11) -4: - tophys(r11, r11) - rlwimi r11, r10, 12, 20, 29 /* Create L1 (pgdir/pmd) address */ - lwz r11, 0(r11) /* Get L1 entry */ - rlwinm. r12, r11, 0, 0, 19 /* Extract L2 (pte) base address */ - beq 2f /* Bail if no table */ - - rlwimi r12, r10, 22, 20, 29 /* Compute PTE address */ - lwz r11, 0(r12) /* Get Linux PTE */ - - andi. r9, r11, _PAGE_RW /* Is it writeable? */ - beq 2f /* Bail if not */ - - /* Update 'changed'. - */ - ori r11, r11, _PAGE_DIRTY|_PAGE_ACCESSED|_PAGE_HWWRITE - stw r11, 0(r12) /* Update Linux page table */ - - /* Most of the Linux PTE is ready to load into the TLB LO. - * We set ZSEL, where only the LS-bit determines user access. - * We set execute, because we don't have the granularity to - * properly set this at the page level (Linux problem). - * If shared is set, we cause a zero PID->TID load. - * Many of these bits are software only. Bits we don't set - * here we (properly should) assume have the appropriate value. - */ - li r12, 0x0ce2 - andc r11, r11, r12 /* Make sure 20, 21 are zero */ - - /* find the TLB index that caused the fault. It has to be here. - */ - tlbsx r9, 0, r10 - - tlbwe r11, r9, TLB_DATA /* Load TLB LO */ - - /* Done...restore registers and get out of here. - */ -#ifdef CONFIG_403GCX - lwz r12, 12(r0) - lwz r11, 8(r0) - mtspr SPRN_PID, r12 - mtcr r11 - lwz r9, 4(r0) - lwz r12, 0(r0) -#else - mfspr r12, SPRN_SPRG6 - mfspr r11, SPRN_SPRG7 - mtspr SPRN_PID, r12 - mtcr r11 - mfspr r9, SPRN_SPRG5 - mfspr r12, SPRN_SPRG4 -#endif - mfspr r11, SPRN_SPRG1 - mfspr r10, SPRN_SPRG0 - PPC405_ERR77_SYNC - rfi /* Should sync shadow TLBs */ - b . /* prevent prefetch past rfi */ - -2: - /* The bailout. Restore registers to pre-exception conditions - * and call the heavyweights to help us out. - */ -#ifdef CONFIG_403GCX - lwz r12, 12(r0) - lwz r11, 8(r0) - mtspr SPRN_PID, r12 - mtcr r11 - lwz r9, 4(r0) - lwz r12, 0(r0) -#else - mfspr r12, SPRN_SPRG6 - mfspr r11, SPRN_SPRG7 - mtspr SPRN_PID, r12 - mtcr r11 - mfspr r9, SPRN_SPRG5 - mfspr r12, SPRN_SPRG4 -#endif - mfspr r11, SPRN_SPRG1 - mfspr r10, SPRN_SPRG0 - b DataAccess - -/* - * 0x0400 - Instruction Storage Exception - * This is caused by a fetch from non-execute or guarded pages. - */ - START_EXCEPTION(0x0400, InstructionAccess) - NORMAL_EXCEPTION_PROLOG - mr r4,r12 /* Pass SRR0 as arg2 */ - li r5,0 /* Pass zero as arg3 */ - EXC_XFER_EE_LITE(0x400, handle_page_fault) - -/* 0x0500 - External Interrupt Exception */ - EXCEPTION(0x0500, HardwareInterrupt, do_IRQ, EXC_XFER_LITE) - -/* 0x0600 - Alignment Exception */ - START_EXCEPTION(0x0600, Alignment) - NORMAL_EXCEPTION_PROLOG - mfspr r4,SPRN_DEAR /* Grab the DEAR and save it */ - stw r4,_DEAR(r11) - addi r3,r1,STACK_FRAME_OVERHEAD - EXC_XFER_EE(0x600, alignment_exception) - -/* 0x0700 - Program Exception */ - START_EXCEPTION(0x0700, ProgramCheck) - NORMAL_EXCEPTION_PROLOG - mfspr r4,SPRN_ESR /* Grab the ESR and save it */ - stw r4,_ESR(r11) - addi r3,r1,STACK_FRAME_OVERHEAD - EXC_XFER_STD(0x700, program_check_exception) - - EXCEPTION(0x0800, Trap_08, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x0900, Trap_09, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x0A00, Trap_0A, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x0B00, Trap_0B, unknown_exception, EXC_XFER_EE) - -/* 0x0C00 - System Call Exception */ - START_EXCEPTION(0x0C00, SystemCall) - NORMAL_EXCEPTION_PROLOG - EXC_XFER_EE_LITE(0xc00, DoSyscall) - - EXCEPTION(0x0D00, Trap_0D, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x0E00, Trap_0E, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x0F00, Trap_0F, unknown_exception, EXC_XFER_EE) - -/* 0x1000 - Programmable Interval Timer (PIT) Exception */ - START_EXCEPTION(0x1000, Decrementer) - NORMAL_EXCEPTION_PROLOG - lis r0,TSR_PIS@h - mtspr SPRN_TSR,r0 /* Clear the PIT exception */ - addi r3,r1,STACK_FRAME_OVERHEAD - EXC_XFER_LITE(0x1000, timer_interrupt) - -#if 0 -/* NOTE: - * FIT and WDT handlers are not implemented yet. - */ - -/* 0x1010 - Fixed Interval Timer (FIT) Exception -*/ - STND_EXCEPTION(0x1010, FITException, unknown_exception) - -/* 0x1020 - Watchdog Timer (WDT) Exception -*/ -#ifdef CONFIG_BOOKE_WDT - CRITICAL_EXCEPTION(0x1020, WDTException, WatchdogException) -#else - CRITICAL_EXCEPTION(0x1020, WDTException, unknown_exception) -#endif -#endif - -/* 0x1100 - Data TLB Miss Exception - * As the name implies, translation is not in the MMU, so search the - * page tables and fix it. The only purpose of this function is to - * load TLB entries from the page table if they exist. - */ - START_EXCEPTION(0x1100, DTLBMiss) - mtspr SPRN_SPRG0, r10 /* Save some working registers */ - mtspr SPRN_SPRG1, r11 -#ifdef CONFIG_403GCX - stw r12, 0(r0) - stw r9, 4(r0) - mfcr r11 - mfspr r12, SPRN_PID - stw r11, 8(r0) - stw r12, 12(r0) -#else - mtspr SPRN_SPRG4, r12 - mtspr SPRN_SPRG5, r9 - mfcr r11 - mfspr r12, SPRN_PID - mtspr SPRN_SPRG7, r11 - mtspr SPRN_SPRG6, r12 -#endif - mfspr r10, SPRN_DEAR /* Get faulting address */ - - /* If we are faulting a kernel address, we have to use the - * kernel page tables. - */ - lis r11, TASK_SIZE@h - cmplw r10, r11 - blt+ 3f - lis r11, swapper_pg_dir@h - ori r11, r11, swapper_pg_dir@l - li r9, 0 - mtspr SPRN_PID, r9 /* TLB will have 0 TID */ - b 4f - - /* Get the PGD for the current thread. - */ -3: - mfspr r11,SPRN_SPRG3 - lwz r11,PGDIR(r11) -4: - tophys(r11, r11) - rlwimi r11, r10, 12, 20, 29 /* Create L1 (pgdir/pmd) address */ - lwz r12, 0(r11) /* Get L1 entry */ - andi. r9, r12, _PMD_PRESENT /* Check if it points to a PTE page */ - beq 2f /* Bail if no table */ - - rlwimi r12, r10, 22, 20, 29 /* Compute PTE address */ - lwz r11, 0(r12) /* Get Linux PTE */ - andi. r9, r11, _PAGE_PRESENT - beq 5f - - ori r11, r11, _PAGE_ACCESSED - stw r11, 0(r12) - - /* Create TLB tag. This is the faulting address plus a static - * set of bits. These are size, valid, E, U0. - */ - li r12, 0x00c0 - rlwimi r10, r12, 0, 20, 31 - - b finish_tlb_load - -2: /* Check for possible large-page pmd entry */ - rlwinm. r9, r12, 2, 22, 24 - beq 5f - - /* Create TLB tag. This is the faulting address, plus a static - * set of bits (valid, E, U0) plus the size from the PMD. - */ - ori r9, r9, 0x40 - rlwimi r10, r9, 0, 20, 31 - mr r11, r12 - - b finish_tlb_load - -5: - /* The bailout. Restore registers to pre-exception conditions - * and call the heavyweights to help us out. - */ -#ifdef CONFIG_403GCX - lwz r12, 12(r0) - lwz r11, 8(r0) - mtspr SPRN_PID, r12 - mtcr r11 - lwz r9, 4(r0) - lwz r12, 0(r0) -#else - mfspr r12, SPRN_SPRG6 - mfspr r11, SPRN_SPRG7 - mtspr SPRN_PID, r12 - mtcr r11 - mfspr r9, SPRN_SPRG5 - mfspr r12, SPRN_SPRG4 -#endif - mfspr r11, SPRN_SPRG1 - mfspr r10, SPRN_SPRG0 - b DataAccess - -/* 0x1200 - Instruction TLB Miss Exception - * Nearly the same as above, except we get our information from different - * registers and bailout to a different point. - */ - START_EXCEPTION(0x1200, ITLBMiss) - mtspr SPRN_SPRG0, r10 /* Save some working registers */ - mtspr SPRN_SPRG1, r11 -#ifdef CONFIG_403GCX - stw r12, 0(r0) - stw r9, 4(r0) - mfcr r11 - mfspr r12, SPRN_PID - stw r11, 8(r0) - stw r12, 12(r0) -#else - mtspr SPRN_SPRG4, r12 - mtspr SPRN_SPRG5, r9 - mfcr r11 - mfspr r12, SPRN_PID - mtspr SPRN_SPRG7, r11 - mtspr SPRN_SPRG6, r12 -#endif - mfspr r10, SPRN_SRR0 /* Get faulting address */ - - /* If we are faulting a kernel address, we have to use the - * kernel page tables. - */ - lis r11, TASK_SIZE@h - cmplw r10, r11 - blt+ 3f - lis r11, swapper_pg_dir@h - ori r11, r11, swapper_pg_dir@l - li r9, 0 - mtspr SPRN_PID, r9 /* TLB will have 0 TID */ - b 4f - - /* Get the PGD for the current thread. - */ -3: - mfspr r11,SPRN_SPRG3 - lwz r11,PGDIR(r11) -4: - tophys(r11, r11) - rlwimi r11, r10, 12, 20, 29 /* Create L1 (pgdir/pmd) address */ - lwz r12, 0(r11) /* Get L1 entry */ - andi. r9, r12, _PMD_PRESENT /* Check if it points to a PTE page */ - beq 2f /* Bail if no table */ - - rlwimi r12, r10, 22, 20, 29 /* Compute PTE address */ - lwz r11, 0(r12) /* Get Linux PTE */ - andi. r9, r11, _PAGE_PRESENT - beq 5f - - ori r11, r11, _PAGE_ACCESSED - stw r11, 0(r12) - - /* Create TLB tag. This is the faulting address plus a static - * set of bits. These are size, valid, E, U0. - */ - li r12, 0x00c0 - rlwimi r10, r12, 0, 20, 31 - - b finish_tlb_load - -2: /* Check for possible large-page pmd entry */ - rlwinm. r9, r12, 2, 22, 24 - beq 5f - - /* Create TLB tag. This is the faulting address, plus a static - * set of bits (valid, E, U0) plus the size from the PMD. - */ - ori r9, r9, 0x40 - rlwimi r10, r9, 0, 20, 31 - mr r11, r12 - - b finish_tlb_load - -5: - /* The bailout. Restore registers to pre-exception conditions - * and call the heavyweights to help us out. - */ -#ifdef CONFIG_403GCX - lwz r12, 12(r0) - lwz r11, 8(r0) - mtspr SPRN_PID, r12 - mtcr r11 - lwz r9, 4(r0) - lwz r12, 0(r0) -#else - mfspr r12, SPRN_SPRG6 - mfspr r11, SPRN_SPRG7 - mtspr SPRN_PID, r12 - mtcr r11 - mfspr r9, SPRN_SPRG5 - mfspr r12, SPRN_SPRG4 -#endif - mfspr r11, SPRN_SPRG1 - mfspr r10, SPRN_SPRG0 - b InstructionAccess - - EXCEPTION(0x1300, Trap_13, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1400, Trap_14, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1500, Trap_15, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1600, Trap_16, unknown_exception, EXC_XFER_EE) -#ifdef CONFIG_IBM405_ERR51 - /* 405GP errata 51 */ - START_EXCEPTION(0x1700, Trap_17) - b DTLBMiss -#else - EXCEPTION(0x1700, Trap_17, unknown_exception, EXC_XFER_EE) -#endif - EXCEPTION(0x1800, Trap_18, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1900, Trap_19, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1A00, Trap_1A, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1B00, Trap_1B, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1C00, Trap_1C, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1D00, Trap_1D, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1E00, Trap_1E, unknown_exception, EXC_XFER_EE) - EXCEPTION(0x1F00, Trap_1F, unknown_exception, EXC_XFER_EE) - -/* Check for a single step debug exception while in an exception - * handler before state has been saved. This is to catch the case - * where an instruction that we are trying to single step causes - * an exception (eg ITLB/DTLB miss) and thus the first instruction of - * the exception handler generates a single step debug exception. - * - * If we get a debug trap on the first instruction of an exception handler, - * we reset the MSR_DE in the _exception handler's_ MSR (the debug trap is - * a critical exception, so we are using SPRN_CSRR1 to manipulate the MSR). - * The exception handler was handling a non-critical interrupt, so it will - * save (and later restore) the MSR via SPRN_SRR1, which will still have - * the MSR_DE bit set. - */ - /* 0x2000 - Debug Exception */ - START_EXCEPTION(0x2000, DebugTrap) - CRITICAL_EXCEPTION_PROLOG - - /* - * If this is a single step or branch-taken exception in an - * exception entry sequence, it was probably meant to apply to - * the code where the exception occurred (since exception entry - * doesn't turn off DE automatically). We simulate the effect - * of turning off DE on entry to an exception handler by turning - * off DE in the SRR3 value and clearing the debug status. - */ - mfspr r10,SPRN_DBSR /* check single-step/branch taken */ - andis. r10,r10,DBSR_IC@h - beq+ 2f - - andi. r10,r9,MSR_IR|MSR_PR /* check supervisor + MMU off */ - beq 1f /* branch and fix it up */ - - mfspr r10,SPRN_SRR2 /* Faulting instruction address */ - cmplwi r10,0x2100 - bgt+ 2f /* address above exception vectors */ - - /* here it looks like we got an inappropriate debug exception. */ -1: rlwinm r9,r9,0,~MSR_DE /* clear DE in the SRR3 value */ - lis r10,DBSR_IC@h /* clear the IC event */ - mtspr SPRN_DBSR,r10 - /* restore state and get out */ - lwz r10,_CCR(r11) - lwz r0,GPR0(r11) - lwz r1,GPR1(r11) - mtcrf 0x80,r10 - mtspr SPRN_SRR2,r12 - mtspr SPRN_SRR3,r9 - lwz r9,GPR9(r11) - lwz r12,GPR12(r11) - lwz r10,crit_r10@l(0) - lwz r11,crit_r11@l(0) - PPC405_ERR77_SYNC - rfci - b . - - /* continue normal handling for a critical exception... */ -2: mfspr r4,SPRN_DBSR - addi r3,r1,STACK_FRAME_OVERHEAD - EXC_XFER_TEMPLATE(DebugException, 0x2002, \ - (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), \ - NOCOPY, crit_transfer_to_handler, ret_from_crit_exc) - -/* - * The other Data TLB exceptions bail out to this point - * if they can't resolve the lightweight TLB fault. - */ -DataAccess: - NORMAL_EXCEPTION_PROLOG - mfspr r5,SPRN_ESR /* Grab the ESR, save it, pass arg3 */ - stw r5,_ESR(r11) - mfspr r4,SPRN_DEAR /* Grab the DEAR, save it, pass arg2 */ - EXC_XFER_EE_LITE(0x300, handle_page_fault) - -/* Other PowerPC processors, namely those derived from the 6xx-series - * have vectors from 0x2100 through 0x2F00 defined, but marked as reserved. - * However, for the 4xx-series processors these are neither defined nor - * reserved. - */ - - /* Damn, I came up one instruction too many to fit into the - * exception space :-). Both the instruction and data TLB - * miss get to this point to load the TLB. - * r10 - TLB_TAG value - * r11 - Linux PTE - * r12, r9 - avilable to use - * PID - loaded with proper value when we get here - * Upon exit, we reload everything and RFI. - * Actually, it will fit now, but oh well.....a common place - * to load the TLB. - */ -tlb_4xx_index: - .long 0 -finish_tlb_load: - /* load the next available TLB index. - */ - lwz r9, tlb_4xx_index@l(0) - addi r9, r9, 1 - andi. r9, r9, (PPC4XX_TLB_SIZE-1) - stw r9, tlb_4xx_index@l(0) - -6: - /* - * Clear out the software-only bits in the PTE to generate the - * TLB_DATA value. These are the bottom 2 bits of the RPM, the - * top 3 bits of the zone field, and M. - */ - li r12, 0x0ce2 - andc r11, r11, r12 - - tlbwe r11, r9, TLB_DATA /* Load TLB LO */ - tlbwe r10, r9, TLB_TAG /* Load TLB HI */ - - /* Done...restore registers and get out of here. - */ -#ifdef CONFIG_403GCX - lwz r12, 12(r0) - lwz r11, 8(r0) - mtspr SPRN_PID, r12 - mtcr r11 - lwz r9, 4(r0) - lwz r12, 0(r0) -#else - mfspr r12, SPRN_SPRG6 - mfspr r11, SPRN_SPRG7 - mtspr SPRN_PID, r12 - mtcr r11 - mfspr r9, SPRN_SPRG5 - mfspr r12, SPRN_SPRG4 -#endif - mfspr r11, SPRN_SPRG1 - mfspr r10, SPRN_SPRG0 - PPC405_ERR77_SYNC - rfi /* Should sync shadow TLBs */ - b . /* prevent prefetch past rfi */ - -/* extern void giveup_fpu(struct task_struct *prev) - * - * The PowerPC 4xx family of processors do not have an FPU, so this just - * returns. - */ -_GLOBAL(giveup_fpu) - blr - -/* This is where the main kernel code starts. - */ -start_here: - - /* ptr to current */ - lis r2,init_task@h - ori r2,r2,init_task@l - - /* ptr to phys current thread */ - tophys(r4,r2) - addi r4,r4,THREAD /* init task's THREAD */ - mtspr SPRN_SPRG3,r4 - - /* stack */ - lis r1,init_thread_union@ha - addi r1,r1,init_thread_union@l - li r0,0 - stwu r0,THREAD_SIZE-STACK_FRAME_OVERHEAD(r1) - - bl early_init /* We have to do this with MMU on */ - -/* - * Decide what sort of machine this is and initialize the MMU. - */ - mr r3,r31 - mr r4,r30 - mr r5,r29 - mr r6,r28 - mr r7,r27 - bl machine_init - bl MMU_init - -/* Go back to running unmapped so we can load up new values - * and change to using our exception vectors. - * On the 4xx, all we have to do is invalidate the TLB to clear - * the old 16M byte TLB mappings. - */ - lis r4,2f@h - ori r4,r4,2f@l - tophys(r4,r4) - lis r3,(MSR_KERNEL & ~(MSR_IR|MSR_DR))@h - ori r3,r3,(MSR_KERNEL & ~(MSR_IR|MSR_DR))@l - mtspr SPRN_SRR0,r4 - mtspr SPRN_SRR1,r3 - rfi - b . /* prevent prefetch past rfi */ - -/* Load up the kernel context */ -2: - sync /* Flush to memory before changing TLB */ - tlbia - isync /* Flush shadow TLBs */ - - /* set up the PTE pointers for the Abatron bdiGDB. - */ - lis r6, swapper_pg_dir@h - ori r6, r6, swapper_pg_dir@l - lis r5, abatron_pteptrs@h - ori r5, r5, abatron_pteptrs@l - stw r5, 0xf0(r0) /* Must match your Abatron config file */ - tophys(r5,r5) - stw r6, 0(r5) - -/* Now turn on the MMU for real! */ - lis r4,MSR_KERNEL@h - ori r4,r4,MSR_KERNEL@l - lis r3,start_kernel@h - ori r3,r3,start_kernel@l - mtspr SPRN_SRR0,r3 - mtspr SPRN_SRR1,r4 - rfi /* enable MMU and jump to start_kernel */ - b . /* prevent prefetch past rfi */ - -/* Set up the initial MMU state so we can do the first level of - * kernel initialization. This maps the first 16 MBytes of memory 1:1 - * virtual to physical and more importantly sets the cache mode. - */ -initial_mmu: - tlbia /* Invalidate all TLB entries */ - isync - - /* We should still be executing code at physical address 0x0000xxxx - * at this point. However, start_here is at virtual address - * 0xC000xxxx. So, set up a TLB mapping to cover this once - * translation is enabled. - */ - - lis r3,KERNELBASE@h /* Load the kernel virtual address */ - ori r3,r3,KERNELBASE@l - tophys(r4,r3) /* Load the kernel physical address */ - - iccci r0,r3 /* Invalidate the i-cache before use */ - - /* Load the kernel PID. - */ - li r0,0 - mtspr SPRN_PID,r0 - sync - - /* Configure and load two entries into TLB slots 62 and 63. - * In case we are pinning TLBs, these are reserved in by the - * other TLB functions. If not reserving, then it doesn't - * matter where they are loaded. - */ - clrrwi r4,r4,10 /* Mask off the real page number */ - ori r4,r4,(TLB_WR | TLB_EX) /* Set the write and execute bits */ - - clrrwi r3,r3,10 /* Mask off the effective page number */ - ori r3,r3,(TLB_VALID | TLB_PAGESZ(PAGESZ_16M)) - - li r0,63 /* TLB slot 63 */ - - tlbwe r4,r0,TLB_DATA /* Load the data portion of the entry */ - tlbwe r3,r0,TLB_TAG /* Load the tag portion of the entry */ - -#if defined(CONFIG_SERIAL_TEXT_DEBUG) && defined(SERIAL_DEBUG_IO_BASE) - - /* Load a TLB entry for the UART, so that ppc4xx_progress() can use - * the UARTs nice and early. We use a 4k real==virtual mapping. */ - - lis r3,SERIAL_DEBUG_IO_BASE@h - ori r3,r3,SERIAL_DEBUG_IO_BASE@l - mr r4,r3 - clrrwi r4,r4,12 - ori r4,r4,(TLB_WR|TLB_I|TLB_M|TLB_G) - - clrrwi r3,r3,12 - ori r3,r3,(TLB_VALID | TLB_PAGESZ(PAGESZ_4K)) - - li r0,0 /* TLB slot 0 */ - tlbwe r4,r0,TLB_DATA - tlbwe r3,r0,TLB_TAG -#endif /* CONFIG_SERIAL_DEBUG_TEXT && SERIAL_DEBUG_IO_BASE */ - - isync - - /* Establish the exception vector base - */ - lis r4,KERNELBASE@h /* EVPR only uses the high 16-bits */ - tophys(r0,r4) /* Use the physical address */ - mtspr SPRN_EVPR,r0 - - blr - -_GLOBAL(abort) - mfspr r13,SPRN_DBCR0 - oris r13,r13,DBCR0_RST_SYSTEM@h - mtspr SPRN_DBCR0,r13 - -_GLOBAL(set_context) - -#ifdef CONFIG_BDI_SWITCH - /* Context switch the PTE pointer for the Abatron BDI2000. - * The PGDIR is the second parameter. - */ - lis r5, KERNELBASE@h - lwz r5, 0xf0(r5) - stw r4, 0x4(r5) -#endif - sync - mtspr SPRN_PID,r3 - isync /* Need an isync to flush shadow */ - /* TLBs after changing PID */ - blr - -/* We put a few things here that have to be page-aligned. This stuff - * goes at the beginning of the data segment, which is page-aligned. - */ - .data - .align 12 - .globl sdata -sdata: - .globl empty_zero_page -empty_zero_page: - .space 4096 - .globl swapper_pg_dir -swapper_pg_dir: - .space 4096 - - -/* Stack for handling critical exceptions from kernel mode */ - .section .bss - .align 12 -exception_stack_bottom: - .space 4096 -critical_stack_top: - .globl exception_stack_top -exception_stack_top: - -/* This space gets a copy of optional info passed to us by the bootstrap - * which is used to pass parameters into the kernel like root=/dev/sda1, etc. - */ - .globl cmd_line -cmd_line: - .space 512 - -/* Room for two PTE pointers, usually the kernel and current user pointers - * to their respective root page table. - */ -abatron_pteptrs: - .space 8 --- /dev/null +++ linux-2.6/arch/powerpc/mm/40x_mmu.c @@ -0,0 +1,135 @@ +/* + * This file contains the routines for initializing the MMU + * on the 4xx series of chips. + * -- paulus + * + * Derived from arch/ppc/mm/init.c: + * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) + * + * Modifications by Paul Mackerras (PowerMac) (paulus@cs.anu.edu.au) + * and Cort Dougan (PReP) (cort@cs.nmt.edu) + * Copyright (C) 1996 Paul Mackerras + * + * Derived from "arch/i386/mm/init.c" + * Copyright (C) 1991, 1992, 1993, 1994 Linus Torvalds + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + */ + +#include <linux/signal.h> +#include <linux/sched.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/string.h> +#include <linux/types.h> +#include <linux/ptrace.h> +#include <linux/mman.h> +#include <linux/mm.h> +#include <linux/swap.h> +#include <linux/stddef.h> +#include <linux/vmalloc.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/highmem.h> + +#include <asm/pgalloc.h> +#include <asm/prom.h> +#include <asm/io.h> +#include <asm/mmu_context.h> +#include <asm/pgtable.h> +#include <asm/mmu.h> +#include <asm/uaccess.h> +#include <asm/smp.h> +#include <asm/bootx.h> +#include <asm/machdep.h> +#include <asm/setup.h> +#include "mmu_decl.h" + +extern int __map_without_ltlbs; +/* + * MMU_init_hw does the chip-specific initialization of the MMU hardware. + */ +void __init MMU_init_hw(void) +{ + /* + * The Zone Protection Register (ZPR) defines how protection will + * be applied to every page which is a member of a given zone. At + * present, we utilize only two of the 4xx's zones. + * The zone index bits (of ZSEL) in the PTE are used for software + * indicators, except the LSB. For user access, zone 1 is used, + * for kernel access, zone 0 is used. We set all but zone 1 + * to zero, allowing only kernel access as indicated in the PTE. + * For zone 1, we set a 01 binary (a value of 10 will not work) + * to allow user access as indicated in the PTE. This also allows + * kernel access as indicated in the PTE. + */ + + mtspr(SPRN_ZPR, 0x10000000); + + flush_instruction_cache(); + + /* + * Set up the real-mode cache parameters for the exception vector + * handlers (which are run in real-mode). + */ + + mtspr(SPRN_DCWR, 0x00000000); /* All caching is write-back */ + + /* + * Cache instruction and data space where the exception + * vectors and the kernel live in real-mode. + */ + + mtspr(SPRN_DCCR, 0xF0000000); /* 512 MB of data space at 0x0. */ + mtspr(SPRN_ICCR, 0xF0000000); /* 512 MB of instr. space at 0x0. */ +} + +#define LARGE_PAGE_SIZE_16M (1<<24) +#define LARGE_PAGE_SIZE_4M (1<<22) + +unsigned long __init mmu_mapin_ram(void) +{ + unsigned long v, s; + phys_addr_t p; + + v = KERNELBASE; + p = PPC_MEMSTART; + s = 0; + + if (__map_without_ltlbs) { + return s; + } + + while (s <= (total_lowmem - LARGE_PAGE_SIZE_16M)) { + pmd_t *pmdp; + unsigned long val = p | _PMD_SIZE_16M | _PAGE_HWEXEC | _PAGE_HWWRITE; + + pmdp = pmd_offset(pgd_offset_k(v), v); + pmd_val(*pmdp++) = val; + pmd_val(*pmdp++) = val; + pmd_val(*pmdp++) = val; + pmd_val(*pmdp++) = val; + + v += LARGE_PAGE_SIZE_16M; + p += LARGE_PAGE_SIZE_16M; + s += LARGE_PAGE_SIZE_16M; + } + + while (s <= (total_lowmem - LARGE_PAGE_SIZE_4M)) { + pmd_t *pmdp; + unsigned long val = p | _PMD_SIZE_4M | _PAGE_HWEXEC | _PAGE_HWWRITE; + + pmdp = pmd_offset(pgd_offset_k(v), v); + pmd_val(*pmdp) = val; + + v += LARGE_PAGE_SIZE_4M; + p += LARGE_PAGE_SIZE_4M; + s += LARGE_PAGE_SIZE_4M; + } + + return s; +} --- linux-2.6.orig/arch/powerpc/mm/4xx_mmu.c +++ /dev/null @@ -1,135 +0,0 @@ -/* - * This file contains the routines for initializing the MMU - * on the 4xx series of chips. - * -- paulus - * - * Derived from arch/ppc/mm/init.c: - * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) - * - * Modifications by Paul Mackerras (PowerMac) (paulus@cs.anu.edu.au) - * and Cort Dougan (PReP) (cort@cs.nmt.edu) - * Copyright (C) 1996 Paul Mackerras - * - * Derived from "arch/i386/mm/init.c" - * Copyright (C) 1991, 1992, 1993, 1994 Linus Torvalds - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. - * - */ - -#include <linux/signal.h> -#include <linux/sched.h> -#include <linux/kernel.h> -#include <linux/errno.h> -#include <linux/string.h> -#include <linux/types.h> -#include <linux/ptrace.h> -#include <linux/mman.h> -#include <linux/mm.h> -#include <linux/swap.h> -#include <linux/stddef.h> -#include <linux/vmalloc.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <linux/highmem.h> - -#include <asm/pgalloc.h> -#include <asm/prom.h> -#include <asm/io.h> -#include <asm/mmu_context.h> -#include <asm/pgtable.h> -#include <asm/mmu.h> -#include <asm/uaccess.h> -#include <asm/smp.h> -#include <asm/bootx.h> -#include <asm/machdep.h> -#include <asm/setup.h> -#include "mmu_decl.h" - -extern int __map_without_ltlbs; -/* - * MMU_init_hw does the chip-specific initialization of the MMU hardware. - */ -void __init MMU_init_hw(void) -{ - /* - * The Zone Protection Register (ZPR) defines how protection will - * be applied to every page which is a member of a given zone. At - * present, we utilize only two of the 4xx's zones. - * The zone index bits (of ZSEL) in the PTE are used for software - * indicators, except the LSB. For user access, zone 1 is used, - * for kernel access, zone 0 is used. We set all but zone 1 - * to zero, allowing only kernel access as indicated in the PTE. - * For zone 1, we set a 01 binary (a value of 10 will not work) - * to allow user access as indicated in the PTE. This also allows - * kernel access as indicated in the PTE. - */ - - mtspr(SPRN_ZPR, 0x10000000); - - flush_instruction_cache(); - - /* - * Set up the real-mode cache parameters for the exception vector - * handlers (which are run in real-mode). - */ - - mtspr(SPRN_DCWR, 0x00000000); /* All caching is write-back */ - - /* - * Cache instruction and data space where the exception - * vectors and the kernel live in real-mode. - */ - - mtspr(SPRN_DCCR, 0xF0000000); /* 512 MB of data space at 0x0. */ - mtspr(SPRN_ICCR, 0xF0000000); /* 512 MB of instr. space at 0x0. */ -} - -#define LARGE_PAGE_SIZE_16M (1<<24) -#define LARGE_PAGE_SIZE_4M (1<<22) - -unsigned long __init mmu_mapin_ram(void) -{ - unsigned long v, s; - phys_addr_t p; - - v = KERNELBASE; - p = PPC_MEMSTART; - s = 0; - - if (__map_without_ltlbs) { - return s; - } - - while (s <= (total_lowmem - LARGE_PAGE_SIZE_16M)) { - pmd_t *pmdp; - unsigned long val = p | _PMD_SIZE_16M | _PAGE_HWEXEC | _PAGE_HWWRITE; - - pmdp = pmd_offset(pgd_offset_k(v), v); - pmd_val(*pmdp++) = val; - pmd_val(*pmdp++) = val; - pmd_val(*pmdp++) = val; - pmd_val(*pmdp++) = val; - - v += LARGE_PAGE_SIZE_16M; - p += LARGE_PAGE_SIZE_16M; - s += LARGE_PAGE_SIZE_16M; - } - - while (s <= (total_lowmem - LARGE_PAGE_SIZE_4M)) { - pmd_t *pmdp; - unsigned long val = p | _PMD_SIZE_4M | _PAGE_HWEXEC | _PAGE_HWWRITE; - - pmdp = pmd_offset(pgd_offset_k(v), v); - pmd_val(*pmdp) = val; - - v += LARGE_PAGE_SIZE_4M; - p += LARGE_PAGE_SIZE_4M; - s += LARGE_PAGE_SIZE_4M; - } - - return s; -} --- linux-2.6.orig/arch/powerpc/mm/Makefile +++ linux-2.6/arch/powerpc/mm/Makefile @@ -13,7 +13,7 @@ obj-$(CONFIG_PPC64) += init_64.o pgtabl hash_utils_64.o hash_low_64.o tlb_64.o \ slb_low.o slb.o stab.o mmap.o $(hash-y) obj-$(CONFIG_PPC_STD_MMU_32) += ppc_mmu_32.o hash_low_32.o tlb_32.o -obj-$(CONFIG_40x) += 4xx_mmu.o +obj-$(CONFIG_40x) += 40x_mmu.o obj-$(CONFIG_44x) += 44x_mmu.o obj-$(CONFIG_FSL_BOOKE) += fsl_booke_mmu.o obj-$(CONFIG_NEED_MULTIPLE_NODES) += numa.o --- /dev/null +++ linux-2.6/arch/powerpc/platforms/40x/Kconfig @@ -0,0 +1,208 @@ +config 4xx + bool + depends on 40x || 44x + default y + +config BOOKE + bool + depends on 44x + default y + +menu "AMCC 40x options" + depends on 40x + +#config BUBINGA +# bool "Bubinga" +# depends on 40x +# default n +# select 405EP +# help +# This option enables support for the IBM 405EP evaluation board. + +#config CPCI405 +# bool "CPCI405" +# depends on 40x +# default n +# select 405GP +# help +# This option enables support for the CPCI405 board. + +#config EP405 +# bool "EP405/EP405PC" +# depends on 40x +# default n +# select 405GP +# help +# This option enables support for the EP405/EP405PC boards. + +#config EP405PC +# bool "EP405PC Support" +# depends on EP405 +# default y +# help +# This option enables support for the extra features of the EP405PC board. + +#config REDWOOD_5 +# bool "Redwood-5" +# depends on 40x +# default n +# select STB03xxx +# help +# This option enables support for the IBM STB04 evaluation board. + +#config REDWOOD_6 +# bool "Redwood-6" +# depends on 40x +# default n +# select STB03xxx +# help +# This option enables support for the IBM STBx25xx evaluation board. + +#config SYCAMORE +# bool "Sycamore" +# depends on 40x +# default n +# select 405GPR +# help +# This option enables support for the IBM PPC405GPr evaluation board. + +#config WALNUT +# bool "Walnut" +# depends on 40x +# default y +# select 405GP +# help +# This option enables support for the IBM PPC405GP evaluation board. + +#config XILINX_ML300 +# bool "Xilinx-ML300" +# depends on 40x +# default y +# select VIRTEX_II_PRO +# help +# This option enables support for the Xilinx ML300 evaluation board. + +endmenu + +# 40x specific CPU modules, selected based on the board above. +config NP405H + bool + #depends on ASH + +# OAK doesn't exist but wanted to keep this around for any future 403GCX boards +config 403GCX + bool + #depends on OAK + select IBM405_ERR51 + +config 405GP + bool + select IBM405_ERR77 + select IBM405_ERR51 + +config 405EP + bool + +config 405GPR + bool + +config VIRTEX_II_PRO + bool + select IBM405_ERR77 + select IBM405_ERR51 + +config STB03xxx + bool + select IBM405_ERR77 + select IBM405_ERR51 + +# 40x errata/workaround config symbols, selected by the CPU models above + +# All 405-based cores up until the 405GPR and 405EP have this errata. +config IBM405_ERR77 + bool + +# All 40x-based cores, up until the 405GPR and 405EP have this errata. +config IBM405_ERR51 + bool + +menu "AMCC 44x options" + depends on 44x + +#config BAMBOO +# bool "Bamboo" +# depends on 44x +# default n +# select 440EP +# help +# This option enables support for the IBM PPC440EP evaluation board. + +config EBONY + bool "Ebony" + depends on 44x + default y + select 440GP + help + This option enables support for the IBM PPC440GP evaluation board. + +#config LUAN +# bool "Luan" +# depends on 44x +# default n +# select 440SP +# help +# This option enables support for the IBM PPC440SP evaluation board. + +#config OCOTEA +# bool "Ocotea" +# depends on 44x +# default n +# select 440GX +# help +# This option enables support for the IBM PPC440GX evaluation board. + +endmenu + +# 44x specific CPU modules, selected based on the board above. +config 440EP + bool + select PPC_FPU + select IBM440EP_ERR42 + +config 440GP + bool + select IBM_NEW_EMAC_ZMII + +config 440GX + bool + +config 440SP + bool + +config 440A + bool + depends on 440GX + default y + +# 44x errata/workaround config symbols, selected by the CPU models above +config IBM440EP_ERR42 + bool + +#config XILINX_OCP +# bool +# depends on XILINX_ML300 +# default y + +#config BIOS_FIXUP +# bool +# depends on BUBINGA || EP405 || SYCAMORE || WALNUT +# default y + +#config PPC4xx_DMA +# bool "PPC4xx DMA controller support" +# depends on 4xx + +#config PPC4xx_EDMA +# bool +# depends on !STB03xxx && PPC4xx_DMA +# default y --- /dev/null +++ linux-2.6/arch/powerpc/platforms/40x/Makefile @@ -0,0 +1 @@ +# empty makefile so make clean works \ No newline at end of file --- linux-2.6.orig/arch/powerpc/platforms/4xx/Kconfig +++ /dev/null @@ -1,208 +0,0 @@ -config 4xx - bool - depends on 40x || 44x - default y - -config BOOKE - bool - depends on 44x - default y - -menu "AMCC 40x options" - depends on 40x - -#config BUBINGA -# bool "Bubinga" -# depends on 40x -# default n -# select 405EP -# help -# This option enables support for the IBM 405EP evaluation board. - -#config CPCI405 -# bool "CPCI405" -# depends on 40x -# default n -# select 405GP -# help -# This option enables support for the CPCI405 board. - -#config EP405 -# bool "EP405/EP405PC" -# depends on 40x -# default n -# select 405GP -# help -# This option enables support for the EP405/EP405PC boards. - -#config EP405PC -# bool "EP405PC Support" -# depends on EP405 -# default y -# help -# This option enables support for the extra features of the EP405PC board. - -#config REDWOOD_5 -# bool "Redwood-5" -# depends on 40x -# default n -# select STB03xxx -# help -# This option enables support for the IBM STB04 evaluation board. - -#config REDWOOD_6 -# bool "Redwood-6" -# depends on 40x -# default n -# select STB03xxx -# help -# This option enables support for the IBM STBx25xx evaluation board. - -#config SYCAMORE -# bool "Sycamore" -# depends on 40x -# default n -# select 405GPR -# help -# This option enables support for the IBM PPC405GPr evaluation board. - -#config WALNUT -# bool "Walnut" -# depends on 40x -# default y -# select 405GP -# help -# This option enables support for the IBM PPC405GP evaluation board. - -#config XILINX_ML300 -# bool "Xilinx-ML300" -# depends on 40x -# default y -# select VIRTEX_II_PRO -# help -# This option enables support for the Xilinx ML300 evaluation board. - -endmenu - -# 40x specific CPU modules, selected based on the board above. -config NP405H - bool - #depends on ASH - -# OAK doesn't exist but wanted to keep this around for any future 403GCX boards -config 403GCX - bool - #depends on OAK - select IBM405_ERR51 - -config 405GP - bool - select IBM405_ERR77 - select IBM405_ERR51 - -config 405EP - bool - -config 405GPR - bool - -config VIRTEX_II_PRO - bool - select IBM405_ERR77 - select IBM405_ERR51 - -config STB03xxx - bool - select IBM405_ERR77 - select IBM405_ERR51 - -# 40x errata/workaround config symbols, selected by the CPU models above - -# All 405-based cores up until the 405GPR and 405EP have this errata. -config IBM405_ERR77 - bool - -# All 40x-based cores, up until the 405GPR and 405EP have this errata. -config IBM405_ERR51 - bool - -menu "AMCC 44x options" - depends on 44x - -#config BAMBOO -# bool "Bamboo" -# depends on 44x -# default n -# select 440EP -# help -# This option enables support for the IBM PPC440EP evaluation board. - -config EBONY - bool "Ebony" - depends on 44x - default y - select 440GP - help - This option enables support for the IBM PPC440GP evaluation board. - -#config LUAN -# bool "Luan" -# depends on 44x -# default n -# select 440SP -# help -# This option enables support for the IBM PPC440SP evaluation board. - -#config OCOTEA -# bool "Ocotea" -# depends on 44x -# default n -# select 440GX -# help -# This option enables support for the IBM PPC440GX evaluation board. - -endmenu - -# 44x specific CPU modules, selected based on the board above. -config 440EP - bool - select PPC_FPU - select IBM440EP_ERR42 - -config 440GP - bool - select IBM_NEW_EMAC_ZMII - -config 440GX - bool - -config 440SP - bool - -config 440A - bool - depends on 440GX - default y - -# 44x errata/workaround config symbols, selected by the CPU models above -config IBM440EP_ERR42 - bool - -#config XILINX_OCP -# bool -# depends on XILINX_ML300 -# default y - -#config BIOS_FIXUP -# bool -# depends on BUBINGA || EP405 || SYCAMORE || WALNUT -# default y - -#config PPC4xx_DMA -# bool "PPC4xx DMA controller support" -# depends on 4xx - -#config PPC4xx_EDMA -# bool -# depends on !STB03xxx && PPC4xx_DMA -# default y --- linux-2.6.orig/arch/powerpc/platforms/4xx/Makefile +++ /dev/null @@ -1 +0,0 @@ -# empty makefile so make clean works \ No newline at end of file -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [patch 02/14] Rename 4xx paths to 40x 2007-07-17 18:15 ` [patch 02/14] Rename 4xx paths to 40x Josh Boyer @ 2007-07-18 3:26 ` David Gibson 0 siblings, 0 replies; 22+ messages in thread From: David Gibson @ 2007-07-18 3:26 UTC (permalink / raw) To: Josh Boyer; +Cc: linuxppc-dev On Tue, Jul 17, 2007 at 01:15:49PM -0500, Josh Boyer wrote: > 4xx is a bit of a misnomer for certain things, as they really apply to PowerPC > 40x only. Rename some of the files to clean this up. > > Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Looks good Acked-by: David Gibson <david@gibson.dropbear.id.au> -- David Gibson | I'll have my music baroque, and my code david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_ | _way_ _around_! http://www.ozlabs.org/~dgibson ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 03/14] 4xx Kconfig cleanup 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer 2007-07-17 18:15 ` [patch 01/14] Use resource_size_t for serial port IO addresses Josh Boyer 2007-07-17 18:15 ` [patch 02/14] Rename 4xx paths to 40x Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:15 ` [patch 04/14] 4xx bootwrapper reworks Josh Boyer ` (10 subsequent siblings) 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev Remove some leftover cruft in the 40x Kconfig file. Also make sure we select WANT_DEVICE_TREE for 40x. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/platforms/40x/Kconfig | 77 --------------------------------- arch/powerpc/platforms/Kconfig.cputype | 1 2 files changed, 1 insertion(+), 77 deletions(-) --- linux-2.6.orig/arch/powerpc/platforms/40x/Kconfig +++ linux-2.6/arch/powerpc/platforms/40x/Kconfig @@ -1,16 +1,3 @@ -config 4xx - bool - depends on 40x || 44x - default y - -config BOOKE - bool - depends on 44x - default y - -menu "AMCC 40x options" - depends on 40x - #config BUBINGA # bool "Bubinga" # depends on 40x @@ -82,8 +69,6 @@ menu "AMCC 40x options" # help # This option enables support for the Xilinx ML300 evaluation board. -endmenu - # 40x specific CPU modules, selected based on the board above. config NP405H bool @@ -126,68 +111,6 @@ config IBM405_ERR77 config IBM405_ERR51 bool -menu "AMCC 44x options" - depends on 44x - -#config BAMBOO -# bool "Bamboo" -# depends on 44x -# default n -# select 440EP -# help -# This option enables support for the IBM PPC440EP evaluation board. - -config EBONY - bool "Ebony" - depends on 44x - default y - select 440GP - help - This option enables support for the IBM PPC440GP evaluation board. - -#config LUAN -# bool "Luan" -# depends on 44x -# default n -# select 440SP -# help -# This option enables support for the IBM PPC440SP evaluation board. - -#config OCOTEA -# bool "Ocotea" -# depends on 44x -# default n -# select 440GX -# help -# This option enables support for the IBM PPC440GX evaluation board. - -endmenu - -# 44x specific CPU modules, selected based on the board above. -config 440EP - bool - select PPC_FPU - select IBM440EP_ERR42 - -config 440GP - bool - select IBM_NEW_EMAC_ZMII - -config 440GX - bool - -config 440SP - bool - -config 440A - bool - depends on 440GX - default y - -# 44x errata/workaround config symbols, selected by the CPU models above -config IBM440EP_ERR42 - bool - #config XILINX_OCP # bool # depends on XILINX_ML300 --- linux-2.6.orig/arch/powerpc/platforms/Kconfig.cputype +++ linux-2.6/arch/powerpc/platforms/Kconfig.cputype @@ -40,6 +40,7 @@ config PPC_8xx config 40x bool "AMCC 40x" select PPC_DCR_NATIVE + select WANT_DEVICE_TREE config 44x bool "AMCC 44x" -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 04/14] 4xx bootwrapper reworks 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (2 preceding siblings ...) 2007-07-17 18:15 ` [patch 03/14] 4xx Kconfig cleanup Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:15 ` [patch 05/14] 40x MMU Josh Boyer ` (9 subsequent siblings) 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev Rename the 44x.c wrapper file to 4xx.c and make the fixup_memsize function common for all of 4xx. Also adds a common function to reset ethernet and a 40x reset function. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/boot/44x.c | 85 ---------------------------------- arch/powerpc/boot/44x.h | 4 - arch/powerpc/boot/4xx.c | 111 +++++++++++++++++++++++++++++++++++++++++++++ arch/powerpc/boot/4xx.h | 20 ++++++++ arch/powerpc/boot/Makefile | 4 - arch/powerpc/boot/dcr.h | 2 arch/powerpc/boot/ebony.c | 3 - 7 files changed, 137 insertions(+), 92 deletions(-) --- linux-2.6.orig/arch/powerpc/boot/44x.h +++ linux-2.6/arch/powerpc/boot/44x.h @@ -10,10 +10,6 @@ #ifndef _PPC_BOOT_44X_H_ #define _PPC_BOOT_44X_H_ -void ibm44x_fixup_memsize(void); -void ibm4xx_fixup_ebc_ranges(const char *ebc); - -void ibm44x_dbcr_reset(void); void ebony_init(void *mac0, void *mac1); #endif /* _PPC_BOOT_44X_H_ */ --- /dev/null +++ linux-2.6/arch/powerpc/boot/4xx.c @@ -0,0 +1,111 @@ +/* + * Copyright 2007 David Gibson, IBM Corporation. + * + * Based on earlier code: + * Matt Porter <mporter@kernel.crashing.org> + * Copyright 2002-2005 MontaVista Software Inc. + * + * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> + * Copyright (c) 2003, 2004 Zultys Technologies + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ +#include <stddef.h> +#include "types.h" +#include "string.h" +#include "stdio.h" +#include "ops.h" +#include "reg.h" +#include "dcr.h" + +/* Read the 4xx SDRAM controller to get size of system memory. */ +void ibm4xx_fixup_memsize(void) +{ + int i; + unsigned long memsize, bank_config; + + memsize = 0; + for (i = 0; i < ARRAY_SIZE(sdram_bxcr); i++) { + mtdcr(DCRN_SDRAM0_CFGADDR, sdram_bxcr[i]); + bank_config = mfdcr(DCRN_SDRAM0_CFGDATA); + + if (bank_config & SDRAM_CONFIG_BANK_ENABLE) + memsize += SDRAM_CONFIG_BANK_SIZE(bank_config); + } + + dt_fixup_memory(0, memsize); +} + +#define DBCR0_RST_SYSTEM 0x30000000 + +void ibm44x_dbcr_reset(void) +{ + unsigned long tmp; + + /* DBCR0 on 44x is SPRN 0x134 */ + asm volatile ( + "mfspr %0,%1\n" + "oris %0,%0,%2@h\n" + "mtspr %1,%0" + : "=&r"(tmp) : "i"(0x134), "i"(DBCR0_RST_SYSTEM) + ); + +} + +void ibm40x_dbcr_reset(void) +{ + unsigned long tmp; + + /* DBCR0 on 4xx is SPRN 0x3F2 */ + asm volatile ( + "mfspr %0,%1\n" + "oris %0,%0,%2@h\n" + "mtspr %1,%0" + : "=&r"(tmp) : "i"(0x3F2), "i"(DBCR0_RST_SYSTEM) + ); +} + +#define EMAC_RESET 0x20000000 +#define MAL_RESET 0x80000000 +void ibm4xx_reset_eth(u32 *emac0, u32 *emac1) +{ + /* Reset the MAL and EMAC(s) since PIBS/OpenBIOS don't do this for us */ + if (emac0) + *emac0 = EMAC_RESET; + if (emac1) + *emac1 = EMAC_RESET; + + mtdcr(DCRN_MAL0_CFG, MAL_RESET); +} + +/* Read 4xx EBC bus bridge registers to get mappings of the peripheral + * banks into the OPB address space */ +void ibm4xx_fixup_ebc_ranges(const char *ebc) +{ + void *devp; + u32 bxcr; + u32 ranges[EBC_NUM_BANKS*4]; + u32 *p = ranges; + int i; + + for (i = 0; i < EBC_NUM_BANKS; i++) { + mtdcr(DCRN_EBC0_CFGADDR, EBC_BXCR(i)); + bxcr = mfdcr(DCRN_EBC0_CFGDATA); + + if ((bxcr & EBC_BXCR_BU) != EBC_BXCR_BU_OFF) { + *p++ = i; + *p++ = 0; + *p++ = bxcr & EBC_BXCR_BAS; + *p++ = EBC_BXCR_BANK_SIZE(bxcr); + } + } + + devp = finddevice(ebc); + if (! devp) + fatal("Couldn't locate EBC node %s\n\r", ebc); + + setprop(devp, "ranges", ranges, (p - ranges) * sizeof(u32)); +} --- /dev/null +++ linux-2.6/arch/powerpc/boot/4xx.h @@ -0,0 +1,20 @@ +/* + * PowerPC 4xx related functions + * + * Copyright 2007 IBM Corporation. + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ +#ifndef _POWERPC_BOOT_4XX_H_ +#define _POWERPC_BOOT_4XX_H_ + +void ibm4xx_fixup_memsize(void); +void ibm44x_dbcr_reset(void); +void ibm40x_dbcr_reset(void); +void ibm4xx_reset_eth(u32 *emac0, u32 *emac1); +void ibm4xx_fixup_ebc_ranges(const char *ebc); + +#endif /* _POWERPC_BOOT_4XX_H_ */ --- linux-2.6.orig/arch/powerpc/boot/dcr.h +++ linux-2.6/arch/powerpc/boot/dcr.h @@ -121,4 +121,6 @@ static const unsigned long sdram_bxcr[] #define DCRN_CPC0_MIRQ1 0x0ed #define DCRN_CPC0_JTAGID 0x0ef +#define DCRN_MAL0_CFG 0x180 + #endif /* _PPC_BOOT_DCR_H_ */ --- linux-2.6.orig/arch/powerpc/boot/ebony.c +++ linux-2.6/arch/powerpc/boot/ebony.c @@ -25,6 +25,7 @@ #include "ops.h" #include "reg.h" #include "dcr.h" +#include "4xx.h" #include "44x.h" extern char _dtb_start[]; @@ -98,7 +99,7 @@ static void ebony_fixups(void) unsigned long sysclk = 33000000; ibm440gp_fixup_clocks(sysclk, 6 * 1843200); - ibm44x_fixup_memsize(); + ibm4xx_fixup_memsize(); dt_fixup_mac_addresses(ebony_mac0, ebony_mac1); ibm4xx_fixup_ebc_ranges("/plb/opb/ebc"); } --- linux-2.6.orig/arch/powerpc/boot/Makefile +++ linux-2.6/arch/powerpc/boot/Makefile @@ -31,7 +31,7 @@ endif BOOTCFLAGS += -I$(obj) -I$(srctree)/$(obj) -$(obj)/44x.o: BOOTCFLAGS += -mcpu=440 +$(obj)/4xx.o: BOOTCFLAGS += -mcpu=440 $(obj)/ebony.o: BOOTCFLAGS += -mcpu=440 zlib := inffast.c inflate.c inftrees.c @@ -44,7 +44,7 @@ $(addprefix $(obj)/,$(zlib) gunzip_util. src-wlib := string.S crt0.S stdio.c main.c flatdevtree.c flatdevtree_misc.c \ ns16550.c serial.c simple_alloc.c div64.S util.S \ gunzip_util.c elf_util.c $(zlib) devtree.c oflib.c ofconsole.c \ - 44x.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c + 4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c src-plat := of.c cuboot-83xx.c cuboot-85xx.c holly.c \ cuboot-ebony.c treeboot-ebony.c prpmc2800.c \ ps3-head.S ps3-hvcall.S ps3.c --- linux-2.6.orig/arch/powerpc/boot/44x.c +++ /dev/null @@ -1,85 +0,0 @@ -/* - * Copyright 2007 David Gibson, IBM Corporation. - * - * Based on earlier code: - * Matt Porter <mporter@kernel.crashing.org> - * Copyright 2002-2005 MontaVista Software Inc. - * - * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> - * Copyright (c) 2003, 2004 Zultys Technologies - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. - */ -#include <stddef.h> -#include "types.h" -#include "string.h" -#include "stdio.h" -#include "ops.h" -#include "reg.h" -#include "dcr.h" - -/* Read the 44x memory controller to get size of system memory. */ -void ibm44x_fixup_memsize(void) -{ - int i; - unsigned long memsize, bank_config; - - memsize = 0; - for (i = 0; i < ARRAY_SIZE(sdram_bxcr); i++) { - mtdcr(DCRN_SDRAM0_CFGADDR, sdram_bxcr[i]); - bank_config = mfdcr(DCRN_SDRAM0_CFGDATA); - - if (bank_config & SDRAM_CONFIG_BANK_ENABLE) - memsize += SDRAM_CONFIG_BANK_SIZE(bank_config); - } - - dt_fixup_memory(0, memsize); -} - -#define SPRN_DBCR0 0x134 -#define DBCR0_RST_SYSTEM 0x30000000 - -void ibm44x_dbcr_reset(void) -{ - unsigned long tmp; - - asm volatile ( - "mfspr %0,%1\n" - "oris %0,%0,%2@h\n" - "mtspr %1,%0" - : "=&r"(tmp) : "i"(SPRN_DBCR0), "i"(DBCR0_RST_SYSTEM) - ); - -} - -/* Read 4xx EBC bus bridge registers to get mappings of the peripheral - * banks into the OPB address space */ -void ibm4xx_fixup_ebc_ranges(const char *ebc) -{ - void *devp; - u32 bxcr; - u32 ranges[EBC_NUM_BANKS*4]; - u32 *p = ranges; - int i; - - for (i = 0; i < EBC_NUM_BANKS; i++) { - mtdcr(DCRN_EBC0_CFGADDR, EBC_BXCR(i)); - bxcr = mfdcr(DCRN_EBC0_CFGDATA); - - if ((bxcr & EBC_BXCR_BU) != EBC_BXCR_BU_OFF) { - *p++ = i; - *p++ = 0; - *p++ = bxcr & EBC_BXCR_BAS; - *p++ = EBC_BXCR_BANK_SIZE(bxcr); - } - } - - devp = finddevice(ebc); - if (! devp) - fatal("Couldn't locate EBC node %s\n\r", ebc); - - setprop(devp, "ranges", ranges, (p - ranges) * sizeof(u32)); -} -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 05/14] 40x MMU 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (3 preceding siblings ...) 2007-07-17 18:15 ` [patch 04/14] 4xx bootwrapper reworks Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-18 3:38 ` David Gibson 2007-07-17 18:15 ` [patch 06/14] 40x decrementer fixes Josh Boyer ` (8 subsequent siblings) 13 siblings, 1 reply; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev Add MMU definitions for 40x platforms. Also fixes two warnings in 40x_mmu.c. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/mm/40x_mmu.c | 4 +- include/asm-powerpc/mmu-40x.h | 65 ++++++++++++++++++++++++++++++++++++++++++ include/asm-powerpc/mmu.h | 3 + 3 files changed, 70 insertions(+), 2 deletions(-) --- /dev/null +++ linux-2.6/include/asm-powerpc/mmu-40x.h @@ -0,0 +1,65 @@ +#ifndef _ASM_POWERPC_MMU_40X_H_ +#define _ASM_POWERPC_MMU_40X_H_ + +/* + * PPC40x support + */ + +#define PPC4XX_TLB_SIZE 64 + +/* + * TLB entries are defined by a "high" tag portion and a "low" data + * portion. On all architectures, the data portion is 32-bits. + * + * TLB entries are managed entirely under software control by reading, + * writing, and searchoing using the 4xx-specific tlbre, tlbwr, and tlbsx + * instructions. + */ + +#define TLB_LO 1 +#define TLB_HI 0 + +#define TLB_DATA TLB_LO +#define TLB_TAG TLB_HI + +/* Tag portion */ + +#define TLB_EPN_MASK 0xFFFFFC00 /* Effective Page Number */ +#define TLB_PAGESZ_MASK 0x00000380 +#define TLB_PAGESZ(x) (((x) & 0x7) << 7) +#define PAGESZ_1K 0 +#define PAGESZ_4K 1 +#define PAGESZ_16K 2 +#define PAGESZ_64K 3 +#define PAGESZ_256K 4 +#define PAGESZ_1M 5 +#define PAGESZ_4M 6 +#define PAGESZ_16M 7 +#define TLB_VALID 0x00000040 /* Entry is valid */ + +/* Data portion */ + +#define TLB_RPN_MASK 0xFFFFFC00 /* Real Page Number */ +#define TLB_PERM_MASK 0x00000300 +#define TLB_EX 0x00000200 /* Instruction execution allowed */ +#define TLB_WR 0x00000100 /* Writes permitted */ +#define TLB_ZSEL_MASK 0x000000F0 +#define TLB_ZSEL(x) (((x) & 0xF) << 4) +#define TLB_ATTR_MASK 0x0000000F +#define TLB_W 0x00000008 /* Caching is write-through */ +#define TLB_I 0x00000004 /* Caching is inhibited */ +#define TLB_M 0x00000002 /* Memory is coherent */ +#define TLB_G 0x00000001 /* Memory is guarded from prefetch */ + +#ifndef __ASSEMBLY__ + +typedef unsigned long phys_addr_t; + +typedef struct { + unsigned long id; + unsigned long vdso_base; +} mm_context_t; + +#endif /* !__ASSEMBLY__ */ + +#endif /* _ASM_POWERPC_MMU_40X_H_ */ --- linux-2.6.orig/include/asm-powerpc/mmu.h +++ linux-2.6/include/asm-powerpc/mmu.h @@ -8,6 +8,9 @@ #elif defined(CONFIG_PPC_STD_MMU) /* 32-bit classic hash table MMU */ # include <asm/mmu-hash32.h> +#elif defined(CONFIG_40x) +/* 40x-style software loaded TLB */ +# include <asm/mmu-40x.h> #elif defined(CONFIG_44x) /* 44x-style software loaded TLB */ # include <asm/mmu-44x.h> --- linux-2.6.orig/arch/powerpc/mm/40x_mmu.c +++ linux-2.6/arch/powerpc/mm/40x_mmu.c @@ -108,7 +108,7 @@ unsigned long __init mmu_mapin_ram(void) pmd_t *pmdp; unsigned long val = p | _PMD_SIZE_16M | _PAGE_HWEXEC | _PAGE_HWWRITE; - pmdp = pmd_offset(pgd_offset_k(v), v); + pmdp = pmd_offset(pud_offset(pgd_offset_k(v), v), v); pmd_val(*pmdp++) = val; pmd_val(*pmdp++) = val; pmd_val(*pmdp++) = val; @@ -123,7 +123,7 @@ unsigned long __init mmu_mapin_ram(void) pmd_t *pmdp; unsigned long val = p | _PMD_SIZE_4M | _PAGE_HWEXEC | _PAGE_HWWRITE; - pmdp = pmd_offset(pgd_offset_k(v), v); + pmdp = pmd_offset(pud_offset(pgd_offset_k(v), v), v); pmd_val(*pmdp) = val; v += LARGE_PAGE_SIZE_4M; -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [patch 05/14] 40x MMU 2007-07-17 18:15 ` [patch 05/14] 40x MMU Josh Boyer @ 2007-07-18 3:38 ` David Gibson 0 siblings, 0 replies; 22+ messages in thread From: David Gibson @ 2007-07-18 3:38 UTC (permalink / raw) To: Josh Boyer; +Cc: linuxppc-dev On Tue, Jul 17, 2007 at 01:15:52PM -0500, Josh Boyer wrote: > Add MMU definitions for 40x platforms. Also fixes two warnings in 40x_mmu.c. > > Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> > > --- > arch/powerpc/mm/40x_mmu.c | 4 +- > include/asm-powerpc/mmu-40x.h | 65 ++++++++++++++++++++++++++++++++++++++++++ > include/asm-powerpc/mmu.h | 3 + > 3 files changed, 70 insertions(+), 2 deletions(-) > > --- /dev/null > +++ linux-2.6/include/asm-powerpc/mmu-40x.h > @@ -0,0 +1,65 @@ > +#ifndef _ASM_POWERPC_MMU_40X_H_ > +#define _ASM_POWERPC_MMU_40X_H_ > + > +/* > + * PPC40x support > + */ > + > +#define PPC4XX_TLB_SIZE 64 This should probably be 40X, like other things. > + > +/* > + * TLB entries are defined by a "high" tag portion and a "low" data > + * portion. On all architectures, the data portion is 32-bits. > + * > + * TLB entries are managed entirely under software control by reading, > + * writing, and searchoing using the 4xx-specific tlbre, tlbwr, and tlbsx > + * instructions. > + */ > + > +#define TLB_LO 1 > +#define TLB_HI 0 > + > +#define TLB_DATA TLB_LO > +#define TLB_TAG TLB_HI > + > +/* Tag portion */ > + > +#define TLB_EPN_MASK 0xFFFFFC00 /* Effective Page Number */ > +#define TLB_PAGESZ_MASK 0x00000380 > +#define TLB_PAGESZ(x) (((x) & 0x7) << 7) > +#define PAGESZ_1K 0 > +#define PAGESZ_4K 1 > +#define PAGESZ_16K 2 > +#define PAGESZ_64K 3 > +#define PAGESZ_256K 4 > +#define PAGESZ_1M 5 > +#define PAGESZ_4M 6 > +#define PAGESZ_16M 7 > +#define TLB_VALID 0x00000040 /* Entry is valid */ > + > +/* Data portion */ > + > +#define TLB_RPN_MASK 0xFFFFFC00 /* Real Page Number */ > +#define TLB_PERM_MASK 0x00000300 > +#define TLB_EX 0x00000200 /* Instruction execution allowed */ > +#define TLB_WR 0x00000100 /* Writes permitted */ > +#define TLB_ZSEL_MASK 0x000000F0 > +#define TLB_ZSEL(x) (((x) & 0xF) << 4) > +#define TLB_ATTR_MASK 0x0000000F > +#define TLB_W 0x00000008 /* Caching is write-through */ > +#define TLB_I 0x00000004 /* Caching is inhibited */ > +#define TLB_M 0x00000002 /* Memory is coherent */ > +#define TLB_G 0x00000001 /* Memory is guarded from prefetch */ > + > +#ifndef __ASSEMBLY__ > + > +typedef unsigned long phys_addr_t; > + > +typedef struct { > + unsigned long id; > + unsigned long vdso_base; > +} mm_context_t; > + > +#endif /* !__ASSEMBLY__ */ > + > +#endif /* _ASM_POWERPC_MMU_40X_H_ */ > --- linux-2.6.orig/include/asm-powerpc/mmu.h > +++ linux-2.6/include/asm-powerpc/mmu.h > @@ -8,6 +8,9 @@ > #elif defined(CONFIG_PPC_STD_MMU) > /* 32-bit classic hash table MMU */ > # include <asm/mmu-hash32.h> > +#elif defined(CONFIG_40x) > +/* 40x-style software loaded TLB */ > +# include <asm/mmu-40x.h> > #elif defined(CONFIG_44x) > /* 44x-style software loaded TLB */ > # include <asm/mmu-44x.h> > --- linux-2.6.orig/arch/powerpc/mm/40x_mmu.c > +++ linux-2.6/arch/powerpc/mm/40x_mmu.c > @@ -108,7 +108,7 @@ unsigned long __init mmu_mapin_ram(void) > pmd_t *pmdp; > unsigned long val = p | _PMD_SIZE_16M | _PAGE_HWEXEC | _PAGE_HWWRITE; > > - pmdp = pmd_offset(pgd_offset_k(v), v); > + pmdp = pmd_offset(pud_offset(pgd_offset_k(v), v), v); > pmd_val(*pmdp++) = val; > pmd_val(*pmdp++) = val; > pmd_val(*pmdp++) = val; > @@ -123,7 +123,7 @@ unsigned long __init mmu_mapin_ram(void) > pmd_t *pmdp; > unsigned long val = p | _PMD_SIZE_4M | _PAGE_HWEXEC | _PAGE_HWWRITE; > > - pmdp = pmd_offset(pgd_offset_k(v), v); > + pmdp = pmd_offset(pud_offset(pgd_offset_k(v), v), v); > pmd_val(*pmdp) = val; > > v += LARGE_PAGE_SIZE_4M; > -- David Gibson | I'll have my music baroque, and my code david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_ | _way_ _around_! http://www.ozlabs.org/~dgibson ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 06/14] 40x decrementer fixes 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (4 preceding siblings ...) 2007-07-17 18:15 ` [patch 05/14] 40x MMU Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:15 ` [patch 07/14] Fix 40x build Josh Boyer ` (7 subsequent siblings) 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev Allow generic_calibrate_decr to work for 40x platforms. Given that the hardware behavior is identical, this also changes the set_dec function to reload the PIT on 40x to match the behavior 44x currently has. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/kernel/time.c | 2 +- include/asm-powerpc/time.h | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) --- linux-2.6.orig/arch/powerpc/kernel/time.c +++ linux-2.6/arch/powerpc/kernel/time.c @@ -866,7 +866,7 @@ void __init generic_calibrate_decr(void) "(not found)\n"); } -#ifdef CONFIG_BOOKE +#if defined(CONFIG_BOOKE) || defined(CONFIG_40x) /* Set the time base to zero */ mtspr(SPRN_TBWL, 0); mtspr(SPRN_TBWU, 0); --- linux-2.6.orig/include/asm-powerpc/time.h +++ linux-2.6/include/asm-powerpc/time.h @@ -174,7 +174,7 @@ static inline unsigned int get_dec(void) static inline void set_dec(int val) { #if defined(CONFIG_40x) - return; /* Have to let it auto-reload */ + mtspr(SPRN_PIT, val); #elif defined(CONFIG_8xx_CPU6) set_dec_cpu6(val); #else -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 07/14] Fix 40x build 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (5 preceding siblings ...) 2007-07-17 18:15 ` [patch 06/14] 40x decrementer fixes Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:15 ` [patch 08/14] Walnut DTS Josh Boyer ` (6 subsequent siblings) 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev Remove inclusion of __res on 40x. We don't need it in arch/powerpc Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/kernel/head_40x.S | 1 - arch/powerpc/kernel/ppc_ksyms.c | 2 +- 2 files changed, 1 insertion(+), 2 deletions(-) --- linux-2.6.orig/arch/powerpc/kernel/ppc_ksyms.c +++ linux-2.6/arch/powerpc/kernel/ppc_ksyms.c @@ -180,7 +180,7 @@ EXPORT_SYMBOL(cacheable_memcpy); EXPORT_SYMBOL(cpm_install_handler); EXPORT_SYMBOL(cpm_free_handler); #endif /* CONFIG_8xx */ -#if defined(CONFIG_8xx) || defined(CONFIG_40x) +#if defined(CONFIG_8xx) EXPORT_SYMBOL(__res); #endif --- linux-2.6.orig/arch/powerpc/kernel/head_40x.S +++ linux-2.6/arch/powerpc/kernel/head_40x.S @@ -35,7 +35,6 @@ #include <asm/page.h> #include <asm/mmu.h> #include <asm/pgtable.h> -#include <asm/ibm4xx.h> #include <asm/cputable.h> #include <asm/thread_info.h> #include <asm/ppc_asm.h> -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 08/14] Walnut DTS 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (6 preceding siblings ...) 2007-07-17 18:15 ` [patch 07/14] Fix 40x build Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:15 ` [patch 09/14] Walnut defconfig Josh Boyer ` (5 subsequent siblings) 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev Device tree source file for the PPC405 Walnut evaluation board. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/boot/dts/walnut.dts | 153 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 153 insertions(+) --- /dev/null +++ linux-2.6/arch/powerpc/boot/dts/walnut.dts @@ -0,0 +1,153 @@ +/* + * Device Tree Source for IBM Walnut + * + * Copyright 2007 IBM Corp. + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * FIXME: Draft only! + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without + * any warranty of any kind, whether express or implied. + * + * To build: + * dtc -I dts -O asm -o walnut.S -b 0 walnut.dts + * dtc -I dts -O dtb -o walnut.dtb -b 0 walnut.dts + */ + +/ { + #address-cells = <1>; + #size-cells = <1>; + model = "ibm,walnut"; + compatible = "ibm,walnut"; + dcr-parent = <&/cpus/PowerPC,405GP@0>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,405GP@0 { + device_type = "cpu"; + reg = <0>; + clock-frequency = <bebc200>; /* Filled in by zImage */ + timebase-frequency = <0>; /* Filled in by zImage */ + i-cache-line-size = <20>; + d-cache-line-size = <20>; + i-cache-size = <4000>; + d-cache-size = <4000>; + dcr-controller; + dcr-access-method = "native"; + }; + }; + + memory { + device_type = "memory"; + reg = <0 0>; /* Filled in by zImage */ + }; + + UIC0: interrupt-controller { + compatible = "ibm,uic"; + interrupt-controller; + cell-index = <0>; + dcr-reg = <0c0 9>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + }; + + plb { + compatible = "ibm,plb3"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + clock-frequency = <0>; /* Filled in by zImage */ + + SDRAM0: memory-controller { + compatible = "ibm,sdram-405gp"; + dcr-reg = <010 2>; + }; + + MAL: mcmal { + compatible = "ibm,mcmal-405gp", "ibm,mcmal"; + dcr-reg = <180 62>; + num-tx-chans = <2>; + num-rx-chans = <1>; + interrupt-parent = <&UIC0>; + interrupts = <a 4 b 4 c 4 d 4 e 4>; + }; + + POB0: opb { + compatible = "ibm,opb"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 ef600000 a00000>; + dcr-reg = <0a0 5>; + clock-frequency = <0>; /* Filled in by zImage */ + + UART0: serial@300 { + device_type = "serial"; + compatible = "ns16550"; + reg = <300 8>; + virtual-reg = <ef600300>; + clock-frequency = <0>; /* Filled in by zImage */ + current-speed = <2580>; + interrupt-parent = <&UIC0>; + interrupts = <0 4>; + }; + + UART1: serial@400 { + device_type = "serial"; + compatible = "ns16550"; + reg = <400 8>; + virtual-reg = <ef600400>; + clock-frequency = <0>; /* Filled in by zImage */ + current-speed = <2580>; + interrupt-parent = <&UIC0>; + interrupts = <1 4>; + }; + + IIC: i2c@500 { + compatible = "ibm,iic-405gp", "ibm,iic"; + reg = <500 11>; + interrupt-parent = <&UIC0>; + interrupts = <2 4>; + }; + + GPIO: gpio@700 { + compatible = "ibm,gpio-405gp"; + reg = <700 20>; + }; + + EMAC: ethernet@800 { + linux,network-index = <0>; + device_type = "network"; + compatible = "ibm,emac-405gp", "ibm,emac"; + interrupt-parent = <&UIC0>; + interrupts = <9 4 f 4>; + reg = <800 70>; + mal-device = <&MAL>; + mal-tx-channel = <0 1>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + }; + + }; + + EBC0: ebc { + compatible = "ibm,ebc-405gp", "ibm,ebc"; + dcr-reg = <012 2>; + #address-cells = <1>; + #size-cells = <1>; + clock-frequency = <0>; /* Filled in by zImage */ + }; + }; + + chosen { + linux,stdout-path = "/plb/opb/serial@300"; + }; +}; -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 09/14] Walnut defconfig 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (7 preceding siblings ...) 2007-07-17 18:15 ` [patch 08/14] Walnut DTS Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:15 ` [patch 10/14] Walnut board support Josh Boyer ` (4 subsequent siblings) 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev Walnut board defconfig Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/configs/walnut_defconfig | 776 ++++++++++++++++++++++++++++++++++ 1 file changed, 776 insertions(+) --- /dev/null +++ linux-2.6/arch/powerpc/configs/walnut_defconfig @@ -0,0 +1,776 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.22-rc4 +# Tue Jul 10 11:16:06 2007 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +# CONFIG_6xx is not set +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_8xx is not set +CONFIG_40x=y +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_4xx=y +# CONFIG_PPC_MM_SLICES is not set +CONFIG_NOT_COHERENT_CACHE=y +CONFIG_PPC32=y +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_IRQ_PER_CPU=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +# CONFIG_PPC_UDBG_16550 is not set +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +# CONFIG_DEFAULT_UIMAGE is not set +CONFIG_PPC_DCR_NATIVE=y +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_PPC_DCR=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +# CONFIG_IPC_NS is not set +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_UTS_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_SYSFS_DEPRECATED=y +# CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +CONFIG_KALLSYMS_ALL=y +CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# +CONFIG_BLOCK=y +CONFIG_LBD=y +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# Platform support +# +# CONFIG_PPC_MPC52xx is not set +# CONFIG_PPC_MPC5200 is not set +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PQ2ADS is not set +CONFIG_WALNUT=y +CONFIG_405GP=y +CONFIG_IBM405_ERR77=y +CONFIG_IBM405_ERR51=y +# CONFIG_MPIC is not set +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set +# CONFIG_PPC_RTAS is not set +# CONFIG_MMIO_NVRAM is not set +# CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_CPM2 is not set + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +# CONFIG_MATH_EMULATION is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_RESOURCES_64BIT=y +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_PROC_DEVICETREE=y +# CONFIG_CMDLINE_BOOL is not set +# CONFIG_PM is not set +CONFIG_SECCOMP=y +CONFIG_WANT_DEVICE_TREE=y +CONFIG_DEVICE_TREE="walnut.dts" +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_ZONE_DMA=y +# CONFIG_PCI is not set +# CONFIG_PCI_DOMAINS is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_HIGHMEM_START=0xfe000000 +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_START=0xff100000 +CONFIG_CONSISTENT_SIZE=0x00200000 +CONFIG_BOOT_LOAD=0x00400000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +CONFIG_CONNECTOR=y +CONFIG_PROC_EVENTS=y +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# +# CONFIG_PNPACPI is not set + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=35000 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# Misc devices +# +# CONFIG_BLINK is not set +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set +# CONFIG_MACINTOSH_DRIVERS is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# Ethernet (10 or 100Mbit) +# +# CONFIG_NET_ETHERNET is not set +# CONFIG_IBM_EMAC is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +# CONFIG_INPUT is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +# CONFIG_SERIAL_8250_MANY_PORTS is not set +CONFIG_SERIAL_8250_SHARE_IRQ=y +# CONFIG_SERIAL_8250_DETECT_IRQ is not set +# CONFIG_SERIAL_8250_RSA is not set + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set +# CONFIG_WATCHDOG is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_NVRAM is not set +# CONFIG_GEN_RTC is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +# CONFIG_I2C is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set +# CONFIG_HWMON is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set +# CONFIG_VGASTATE is not set +# CONFIG_FB is not set +# CONFIG_FB_IBM_GXT4500 is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +# CONFIG_USB_ARCH_HAS_HCD is not set +# CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# InfiniBand support +# + +# +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock +# +# CONFIG_RTC_CLASS is not set + +# +# DMA Engine support +# +# CONFIG_DMA_ENGINE is not set + +# +# DMA Clients +# + +# +# DMA Devices +# + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Distributed Lock Manager +# +# CONFIG_DLM is not set +# CONFIG_UCC_SLOW is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y + +# +# Instrumentation Support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_LIST is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_DEBUGGER is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +CONFIG_CRYPTO=y +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_WP512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_GF128MUL is not set +CONFIG_CRYPTO_ECB=y +CONFIG_CRYPTO_CBC=y +CONFIG_CRYPTO_PCBC=y +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_TWOFISH is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Hardware crypto devices +# -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 10/14] Walnut board support 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (8 preceding siblings ...) 2007-07-17 18:15 ` [patch 09/14] Walnut defconfig Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:15 ` [patch 11/14] Walnut zImage wrapper Josh Boyer ` (3 subsequent siblings) 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev Board support for the PPC405 Walnut evaluation board Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/platforms/40x/Kconfig | 14 +++---- arch/powerpc/platforms/40x/Makefile | 2 - arch/powerpc/platforms/40x/walnut.c | 68 ++++++++++++++++++++++++++++++++++++ arch/powerpc/platforms/Kconfig | 2 - arch/powerpc/platforms/Makefile | 2 - 5 files changed, 78 insertions(+), 10 deletions(-) --- linux-2.6.orig/arch/powerpc/platforms/40x/Makefile +++ linux-2.6/arch/powerpc/platforms/40x/Makefile @@ -1 +1 @@ -# empty makefile so make clean works \ No newline at end of file +obj-$(CONFIG_WALNUT) += walnut.o --- /dev/null +++ linux-2.6/arch/powerpc/platforms/40x/walnut.c @@ -0,0 +1,68 @@ +/* + * Architecture- / platform-specific boot-time initialization code for + * IBM PowerPC 4xx based boards. Adapted from original + * code by Gary Thomas, Cort Dougan <cort@fsmlabs.com>, and Dan Malek + * <dan@net4x.com>. + * + * Copyright(c) 1999-2000 Grant Erickson <grant@lcse.umn.edu> + * + * Rewritten and ported to the merged powerpc tree: + * Copyright 2007 IBM Corporation + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * 2002 (c) MontaVista, Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ + +#include <linux/init.h> +#include <asm/machdep.h> +#include <asm/prom.h> +#include <asm/udbg.h> +#include <asm/time.h> +#include <asm/uic.h> +#include <asm/of_platform.h> + +static struct of_device_id walnut_of_bus[] = { + { .compatible = "ibm,plb", }, + { .compatible = "ibm,opb", }, + { .compatible = "ibm,ebc", }, + {}, +}; + +static int __init walnut_device_probe(void) +{ + if (!machine_is(walnut)) + return 0; + + /* FIXME: do bus probe here */ + of_platform_bus_probe(NULL, walnut_of_bus, NULL); + + return 0; +} +device_initcall(walnut_device_probe); + +static int __init walnut_probe(void) +{ + unsigned long root = of_get_flat_dt_root(); + + if (!of_flat_dt_is_compatible(root, "ibm,walnut")) + return 0; + + return 1; +} + +static void __init walnut_setup_arch(void) +{ +} + +define_machine(walnut) { + .name = "Walnut", + .probe = walnut_probe, + .setup_arch = walnut_setup_arch, + .progress = udbg_progress, + .init_IRQ = uic_init_tree, + .get_irq = uic_get_irq, + .calibrate_decr = generic_calibrate_decr, +}; --- linux-2.6.orig/arch/powerpc/platforms/40x/Kconfig +++ linux-2.6/arch/powerpc/platforms/40x/Kconfig @@ -53,13 +53,13 @@ # help # This option enables support for the IBM PPC405GPr evaluation board. -#config WALNUT -# bool "Walnut" -# depends on 40x -# default y -# select 405GP -# help -# This option enables support for the IBM PPC405GP evaluation board. +config WALNUT + bool "Walnut" + depends on 40x + default y + select 405GP + help + This option enables support for the IBM PPC405GP evaluation board. #config XILINX_ML300 # bool "Xilinx-ML300" --- linux-2.6.orig/arch/powerpc/platforms/Kconfig +++ linux-2.6/arch/powerpc/platforms/Kconfig @@ -58,7 +58,7 @@ source "arch/powerpc/platforms/85xx/Kcon source "arch/powerpc/platforms/86xx/Kconfig" source "arch/powerpc/platforms/embedded6xx/Kconfig" source "arch/powerpc/platforms/44x/Kconfig" -#source "arch/powerpc/platforms/4xx/Kconfig +source "arch/powerpc/platforms/40x/Kconfig" config PPC_NATIVE bool --- linux-2.6.orig/arch/powerpc/platforms/Makefile +++ linux-2.6/arch/powerpc/platforms/Makefile @@ -6,7 +6,7 @@ obj-$(CONFIG_PPC_PMAC) += powermac/ endif endif obj-$(CONFIG_PPC_CHRP) += chrp/ -#obj-$(CONFIG_4xx) += 4xx/ +obj-$(CONFIG_40x) += 40x/ obj-$(CONFIG_44x) += 44x/ obj-$(CONFIG_PPC_MPC52xx) += 52xx/ obj-$(CONFIG_PPC_8xx) += 8xx/ -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 11/14] Walnut zImage wrapper 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (9 preceding siblings ...) 2007-07-17 18:15 ` [patch 10/14] Walnut board support Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:15 ` [patch 12/14] Bamboo DTS Josh Boyer ` (2 subsequent siblings) 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev Add zImage wrapper for walnut board Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/boot/Makefile | 3 - arch/powerpc/boot/treeboot-walnut.c | 92 ++++++++++++++++++++++++++++++++++++ 2 files changed, 94 insertions(+), 1 deletion(-) --- linux-2.6.orig/arch/powerpc/boot/Makefile +++ linux-2.6/arch/powerpc/boot/Makefile @@ -47,7 +47,7 @@ src-wlib := string.S crt0.S stdio.c main 4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c src-plat := of.c cuboot-83xx.c cuboot-85xx.c holly.c \ cuboot-ebony.c treeboot-ebony.c prpmc2800.c \ - ps3-head.S ps3-hvcall.S ps3.c + ps3-head.S ps3-hvcall.S ps3.c treeboot-walnut.c src-boot := $(src-wlib) $(src-plat) empty.c src-boot := $(addprefix $(obj)/, $(src-boot)) @@ -142,6 +142,7 @@ ifneq ($(CONFIG_DEVICE_TREE),"") image-$(CONFIG_PPC_83xx) += cuImage.83xx image-$(CONFIG_PPC_85xx) += cuImage.85xx image-$(CONFIG_EBONY) += treeImage.ebony cuImage.ebony +image-$(CONFIG_WALNUT) += treeImage.walnut endif # For 32-bit powermacs, build the COFF and miboot images --- /dev/null +++ linux-2.6/arch/powerpc/boot/treeboot-walnut.c @@ -0,0 +1,92 @@ +/* + * Old U-boot compatibility for Walnut + * + * Author: Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * Copyright 2007 IBM Corporation + * Based on cuboot-83xx.c, which is: + * Copyright (c) 2007 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include "ops.h" +#include "stdio.h" +#include "dcr.h" +#include "4xx.h" + +extern char _end[]; +extern char _dtb_start[]; +extern char _dtb_end[]; + +BSS_STACK(4096); + +void ibm405gp_fixup_clocks(unsigned int sysclk, unsigned int ser_clk) +{ + u32 pllmr = mfdcr(0xb0); + u32 cpc0_cr0 = mfdcr(0xb1); + u32 cpc0_cr1 = mfdcr(0xb2); + u32 cpu, plb, opb, ebc, tb, uart0, uart1, m; + u32 fwdv, fbdv, cbdv, opdv, epdv, udiv; + + fwdv = (8 - ((pllmr & 0xe0000000) >> 29)); + fbdv = (pllmr & 0x1e000000) >> 25; + cbdv = ((pllmr & 0x00060000) >> 17) + 1; + opdv = ((pllmr & 0x00018000) >> 15) + 1; + epdv = ((pllmr & 0x00001800) >> 13) + 2; + udiv = ((cpc0_cr0 & 0x3e) >> 1) + 1; + + m = fwdv * fbdv * cbdv; + + cpu = sysclk * m / fwdv; + plb = cpu / cbdv; + opb = plb / opdv; + ebc = plb / epdv; + + if (cpc0_cr0 & 0x80) { + /* uart0 uses the external clock */ + uart0 = ser_clk; + } else { + uart0 = cpu / udiv; + } + + if (cpc0_cr0 & 0x40) { + /* uart1 uses the external clock */ + uart1 = ser_clk; + } else { + uart1 = cpu / udiv; + } + + /* setup the timebase clock to tick at the cpu frequency */ + cpc0_cr1 = cpc0_cr1 & ~ 0x00800000; + mtdcr(0xb2, cpc0_cr1); + tb = cpu; + + dt_fixup_cpu_clocks(cpu, tb, 0); + dt_fixup_clock("/plb", plb); + dt_fixup_clock("/plb/opb", opb); + dt_fixup_clock("/plb/ebc", ebc); + dt_fixup_clock("/plb/opb/serial@300", uart0); + dt_fixup_clock("/plb/opb/serial@400", uart1); +} + +static void walnut_fixups(void) +{ + ibm4xx_fixup_memsize(); + ibm405gp_fixup_clocks(33330000, 0xa8c000); + ibm4xx_reset_eth((u32 *)0xef600800, NULL); +} + +void platform_init(void) +{ + unsigned long end_of_ram = 0x2000000; + unsigned long avail_ram = end_of_ram - (unsigned long) _end; + + simple_alloc_init(_end, avail_ram, 32, 32); + platform_ops.fixups = walnut_fixups; + platform_ops.exit = ibm40x_dbcr_reset; + ft_init(_dtb_start, _dtb_end - _dtb_start, 32); + serial_console_init(); +} -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 12/14] Bamboo DTS 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (10 preceding siblings ...) 2007-07-17 18:15 ` [patch 11/14] Walnut zImage wrapper Josh Boyer @ 2007-07-17 18:15 ` Josh Boyer 2007-07-17 18:16 ` [patch 13/14] Bamboo board support Josh Boyer 2007-07-17 18:16 ` [patch 14/14] Bamboo zImage wrapper Josh Boyer 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:15 UTC (permalink / raw) To: linuxppc-dev AMCC Bamboo board DTS Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/boot/dts/bamboo.dts | 248 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 248 insertions(+) --- /dev/null +++ linux-2.6/arch/powerpc/boot/dts/bamboo.dts @@ -0,0 +1,248 @@ +/* + * Device Tree Source for AMCC Bamboo + * + * Copyright (c) 2006, 2007 IBM Corp. + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * FIXME: Draft only! + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without + * any warranty of any kind, whether express or implied. + * + * To build: + * dtc -I dts -O asm -o bamboo.S -b 0 bamboo.dts + * dtc -I dts -O dtb -o bamboo.dtb -b 0 bamboo.dts + */ + +/ { + #address-cells = <2>; + #size-cells = <1>; + model = "amcc,bamboo"; + compatible = "amcc,bamboo"; + dcr-parent = <&/cpus/PowerPC,440EP@0>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,440EP@0 { + device_type = "cpu"; + reg = <0>; + clock-frequency = <0>; /* Filled in by zImage */ + timebase-frequency = <0>; /* Filled in by zImage */ + i-cache-line-size = <20>; + d-cache-line-size = <20>; + i-cache-size = <8000>; + d-cache-size = <8000>; + dcr-controller; + dcr-access-method = "native"; + }; + }; + + memory { + device_type = "memory"; + reg = <0 0 0>; /* Filled in by zImage */ + }; + + UIC0: interrupt-controller0 { + compatible = "ibm,uic-440gp","ibm,uic"; + interrupt-controller; + cell-index = <0>; + dcr-reg = <0c0 009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + }; + + UIC1: interrupt-controller1 { + compatible = "ibm,uic-440gp","ibm,uic"; + interrupt-controller; + cell-index = <1>; + dcr-reg = <0d0 009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + interrupts = <1e 4 1f 4>; /* cascade */ + interrupt-parent = <&UIC0>; + }; + + SDR0: sdr { + compatible = "ibm,sdr-440ep"; + dcr-reg = <00e 002>; + }; + + CPR0: cpr { + compatible = "ibm,cpr-440ep"; + dcr-reg = <00c 002>; + }; + + plb { + compatible = "ibm,plb-440gp", "ibm,plb4"; + #address-cells = <2>; + #size-cells = <1>; + ranges; + clock-frequency = <0>; /* Filled in by zImage */ + + SDRAM0: sdram { + compatible = "ibm,sdram-405gp"; + dcr-reg = <010 2>; + }; + + DMA0: dma { + compatible = "ibm,dma-440gp"; + dcr-reg = <100 027>; + }; + + MAL0: mcmal { + compatible = "ibm,mcmal-440gp", "ibm,mcmal"; + dcr-reg = <180 62>; + num-tx-chans = <4>; + num-rx-chans = <4>; + interrupt-parent = <&MAL0>; + interrupts = <0 1 2 3 4>; + #interrupt-cells = <1>; + interrupt-map = </*TXEOB*/ 0 &UIC0 a 4 + /*RXEOB*/ 1 &UIC0 b 4 + /*SERR*/ 2 &UIC1 0 4 + /*TXDE*/ 3 &UIC1 1 4 + /*RXDE*/ 4 &UIC1 3 4>; + }; + + POB0: opb { + compatible = "ibm,opb-440gp", "ibm,opb"; + #address-cells = <1>; + #size-cells = <1>; + /* Bamboo is oddball in the 44x world and doesn't use the ERPN + * bits. + */ + ranges = <00000000 0 00000000 80000000 + 80000000 0 80000000 80000000>; + interrupt-parent = <&UIC1>; + interrupts = <7 4>; + clock-frequency = <0>; /* Filled in by zImage */ + + EBC0: ebc { + compatible = "ibm,ebc-440gp", "ibm,ebc"; + dcr-reg = <012 2>; + #address-cells = <2>; + #size-cells = <1>; + clock-frequency = <0>; /* Filled in by zImage */ + ranges; + interrupts = <5 1>; + interrupt-parent = <&UIC1>; + }; + + UART0: serial@ef600300 { + device_type = "serial"; + compatible = "ns16550"; + reg = <ef600300 8>; + virtual-reg = <ef600300>; + clock-frequency = <0>; /* Filled in by zImage */ + current-speed = <1c200>; + interrupt-parent = <&UIC0>; + interrupts = <0 4>; + }; + + UART1: serial@ef600400 { + device_type = "serial"; + compatible = "ns16550"; + reg = <ef600400 8>; + virtual-reg = <ef600400>; + clock-frequency = <0>; + current-speed = <0>; + interrupt-parent = <&UIC0>; + interrupts = <1 4>; + }; + + UART2: serial@ef600500 { + device_type = "serial"; + compatible = "ns16550"; + reg = <ef600500 8>; + virtual-reg = <ef600500>; + clock-frequency = <0>; + current-speed = <0>; + interrupt-parent = <&UIC0>; + interrupts = <3 4>; + }; + + UART3: serial@ef600600 { + device_type = "serial"; + compatible = "ns16550"; + reg = <ef600600 8>; + virtual-reg = <ef600600>; + clock-frequency = <0>; + current-speed = <0>; + interrupt-parent = <&UIC0>; + interrupts = <4 4>; + }; + + IIC0: i2c@ef600700 { + device_type = "i2c"; + compatible = "ibm,iic-440gp", "ibm,iic"; + reg = <ef600700 14>; + interrupt-parent = <&UIC0>; + interrupts = <2 4>; + }; + + IIC1: i2c@ef600800 { + device_type = "i2c"; + compatible = "ibm,iic-44gp", "ibm,iic"; + reg = <ef600800 14>; + interrupt-parent = <&UIC0>; + interrupts = <7 4>; + }; + + ZMII0: emac-zmii@ef600d00 { + device_type = "zmii-interface"; + compatible = "ibm,zmii-440gp", "ibm,zmii"; + reg = <ef600d00 c>; + }; + + EMAC0: ethernet@ef600e00 { + device_type = "network"; + compatible = "ibm,emac-440gp", "ibm,emac"; + interrupt-parent = <&UIC1>; + interrupts = <1c 4 1d 4>; + reg = <ef600e00 70>; + local-mac-address = [000000000000]; + mal-device = <&MAL0>; + mal-tx-channel = <0 1>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + zmii-device = <&ZMII0>; + zmii-channel = <0>; + }; + + EMAC1: ethernet@ef600f00 { + device_type = "network"; + compatible = "ibm,emac-440gp", "ibm,emac"; + interrupt-parent = <&UIC1>; + interrupts = <1e 4 1f 4>; + reg = <ef600f00 70>; + local-mac-address = [000000000000]; + mal-device = <&MAL0>; + mal-tx-channel = <2 3>; + mal-rx-channel = <1>; + cell-index = <1>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + zmii-device = <&ZMII0>; + zmii-channel = <1>; + }; + }; + }; + + chosen { + linux,stdout-path = "/plb/opb/serial@ef600300"; + bootargs = "console=ttyS0,115200"; + }; +}; -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 13/14] Bamboo board support 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (11 preceding siblings ...) 2007-07-17 18:15 ` [patch 12/14] Bamboo DTS Josh Boyer @ 2007-07-17 18:16 ` Josh Boyer 2007-07-17 18:16 ` [patch 14/14] Bamboo zImage wrapper Josh Boyer 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:16 UTC (permalink / raw) To: linuxppc-dev Add support for the AMCC Bamboo board Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/configs/bamboo_defconfig | 906 ++++++++++++++++++++++++++++++++++ arch/powerpc/platforms/44x/Kconfig | 15 arch/powerpc/platforms/44x/Makefile | 1 arch/powerpc/platforms/44x/bamboo.c | 66 ++ 4 files changed, 981 insertions(+), 7 deletions(-) --- /dev/null +++ linux-2.6/arch/powerpc/configs/bamboo_defconfig @@ -0,0 +1,906 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.21 +# Mon May 14 07:25:36 2007 +# +# CONFIG_PPC64 is not set +CONFIG_PPC32=y +CONFIG_PPC_MERGE=y +CONFIG_MMU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_IRQ_PER_CPU=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_PPC_UDBG_16550=y +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +# CONFIG_DEFAULT_UIMAGE is not set + +# +# Processor support +# +# CONFIG_CLASSIC32 is not set +# CONFIG_PPC_82xx is not set +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_86xx is not set +# CONFIG_PPC_8xx is not set +# CONFIG_40x is not set +CONFIG_44x=y +# CONFIG_E200 is not set +CONFIG_PPC_FPU=y +CONFIG_PPC_DCR_NATIVE=y +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_PPC_DCR=y +CONFIG_4xx=y +CONFIG_BOOKE=y +CONFIG_PTE_64BIT=y +CONFIG_PHYS_64BIT=y +# CONFIG_PPC_MM_SLICES is not set +CONFIG_NOT_COHERENT_CACHE=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +# CONFIG_IPC_NS is not set +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_UTS_NS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_SYSFS_DEPRECATED=y +# CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# +CONFIG_BLOCK=y +CONFIG_LBD=y +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" + +# +# Platform support +# +# CONFIG_PPC_MPC52xx is not set +# CONFIG_PPC_MPC5200 is not set +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PQ2ADS is not set +CONFIG_BAMBOO=y +# CONFIG_EBONY is not set +CONFIG_440EP=y +CONFIG_IBM440EP_ERR42=y +# CONFIG_MPIC is not set +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set +# CONFIG_PPC_RTAS is not set +# CONFIG_MMIO_NVRAM is not set +# CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_CPM2 is not set + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +CONFIG_MATH_EMULATION=y +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_RESOURCES_64BIT=y +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_PROC_DEVICETREE=y +CONFIG_CMDLINE_BOOL=y +CONFIG_CMDLINE="" +CONFIG_SECCOMP=y +CONFIG_WANT_DEVICE_TREE=y +CONFIG_DEVICE_TREE="bamboo.dts" +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_ZONE_DMA=y +CONFIG_PPC_INDIRECT_PCI=y +# CONFIG_PPC_INDIRECT_PCI_BE is not set +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +# CONFIG_PCIEPORTBUS is not set +CONFIG_ARCH_SUPPORTS_MSI=y +# CONFIG_PCI_MSI is not set +# CONFIG_PCI_DEBUG is not set + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set +# CONFIG_HOTPLUG_PCI is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_HIGHMEM_START=0xfe000000 +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_TASK_SIZE=0x80000000 +CONFIG_CONSISTENT_START=0xff100000 +CONFIG_CONSISTENT_SIZE=0x00200000 +CONFIG_BOOT_LOAD=0x01000000 + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set + +# +# DCCP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_DCCP is not set + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set + +# +# TIPC Configuration (EXPERIMENTAL) +# +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +CONFIG_CONNECTOR=y +CONFIG_PROC_EVENTS=y +# CONFIG_MTD is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# +# CONFIG_PNPACPI is not set + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=35000 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# Misc devices +# +# CONFIG_PHANTOM is not set +# CONFIG_SGI_IOC4 is not set +# CONFIG_TIFM_CORE is not set +# CONFIG_BLINK is not set + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_NETLINK is not set + +# +# Serial ATA (prod) and Parallel ATA (experimental) drivers +# +# CONFIG_ATA is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set + +# +# I2O device support +# +# CONFIG_I2O is not set +CONFIG_MACINTOSH_DRIVERS=y +# CONFIG_MAC_EMUMOUSEBTN is not set +# CONFIG_WINDFARM is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# ARCnet devices +# +# CONFIG_ARCNET is not set + +# +# PHY device support +# + +# +# Ethernet (10 or 100Mbit) +# +# CONFIG_NET_ETHERNET is not set +# CONFIG_IBM_EMAC is not set + +# +# Ethernet (1000 Mbit) +# +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +# CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set + +# +# Ethernet (10000 Mbit) +# +# CONFIG_CHELSIO_T1 is not set +# CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGB is not set +# CONFIG_S2IO is not set +# CONFIG_MYRI10GE is not set +# CONFIG_NETXEN_NIC is not set +# CONFIG_MLX4_CORE is not set +CONFIG_MLX4_DEBUG=y + +# +# Token Ring devices +# +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +# CONFIG_INPUT is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_VT is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +# CONFIG_SERIAL_8250_PCI is not set +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +# CONFIG_SERIAL_8250_MANY_PORTS is not set +CONFIG_SERIAL_8250_SHARE_IRQ=y +# CONFIG_SERIAL_8250_DETECT_IRQ is not set +# CONFIG_SERIAL_8250_RSA is not set + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set +# CONFIG_WATCHDOG is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_NVRAM is not set +# CONFIG_GEN_RTC is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +# CONFIG_I2C is not set + +# +# SPI support +# +# CONFIG_SPI is not set +# CONFIG_SPI_MASTER is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set +# CONFIG_HWMON is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +CONFIG_DAB=y + +# +# Graphics support +# +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set +# CONFIG_VGASTATE is not set +# CONFIG_FB is not set +# CONFIG_FB_IBM_GXT4500 is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +# CONFIG_USB is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# InfiniBand support +# +# CONFIG_INFINIBAND is not set + +# +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock +# +# CONFIG_RTC_CLASS is not set + +# +# DMA Engine support +# +# CONFIG_DMA_ENGINE is not set + +# +# DMA Clients +# + +# +# DMA Devices +# + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +# CONFIG_NLS is not set + +# +# Distributed Lock Manager +# +# CONFIG_DLM is not set +# CONFIG_UCC_SLOW is not set +# CONFIG_UCC_FAST is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y + +# +# Instrumentation Support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_LIST is not set +CONFIG_FORCED_INLINING=y +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +CONFIG_DEBUGGER=y +# CONFIG_KGDB is not set +# CONFIG_XMON is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set +CONFIG_PPC_EARLY_DEBUG=y +# CONFIG_PPC_EARLY_DEBUG_LPAR is not set +# CONFIG_PPC_EARLY_DEBUG_G5 is not set +# CONFIG_PPC_EARLY_DEBUG_RTAS_PANEL is not set +# CONFIG_PPC_EARLY_DEBUG_RTAS_CONSOLE is not set +# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set +# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set +# CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set +# CONFIG_PPC_EARLY_DEBUG_BEAT is not set +CONFIG_PPC_EARLY_DEBUG_44x=y +CONFIG_PPC_EARLY_DEBUG_44x_PHYSLOW=0xef600300 +CONFIG_PPC_EARLY_DEBUG_44x_PHYSHIGH=0x0 + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +CONFIG_CRYPTO=y +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_WP512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_GF128MUL is not set +CONFIG_CRYPTO_ECB=y +CONFIG_CRYPTO_CBC=y +CONFIG_CRYPTO_PCBC=y +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_TWOFISH is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Hardware crypto devices +# --- linux-2.6.orig/arch/powerpc/platforms/44x/Kconfig +++ linux-2.6/arch/powerpc/platforms/44x/Kconfig @@ -1,10 +1,10 @@ -#config BAMBOO -# bool "Bamboo" -# depends on 44x -# default n -# select 440EP -# help -# This option enables support for the IBM PPC440EP evaluation board. +config BAMBOO + bool "Bamboo" + depends on 44x + default n + select 440EP + help + This option enables support for the IBM PPC440EP evaluation board. config EBONY bool "Ebony" @@ -35,6 +35,7 @@ config 440EP bool select PPC_FPU select IBM440EP_ERR42 +# select IBM_NEW_EMAC_ZMII config 440GP bool --- linux-2.6.orig/arch/powerpc/platforms/44x/Makefile +++ linux-2.6/arch/powerpc/platforms/44x/Makefile @@ -1,2 +1,3 @@ obj-$(CONFIG_44x) := misc_44x.o obj-$(CONFIG_EBONY) += ebony.o +obj-$(CONFIG_BAMBOO) += bamboo.o --- /dev/null +++ linux-2.6/arch/powerpc/platforms/44x/bamboo.c @@ -0,0 +1,66 @@ +/* + * Bamboo board specific routines + * + * Wade Farnsworth <wfarnsworth@mvista.com> + * Copyright 2004 MontaVista Software Inc. + * + * Rewritten and ported to the merged powerpc tree: + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * Copyright 2007 IBM Corporation + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#include <linux/init.h> +#include <asm/machdep.h> +#include <asm/prom.h> +#include <asm/udbg.h> +#include <asm/time.h> +#include <asm/uic.h> +#include <asm/of_platform.h> +#include "44x.h" + +static struct of_device_id bamboo_of_bus[] = { + { .compatible = "ibm,plb", }, + { .compatible = "ibm,opb", }, + { .compatible = "ibm,ebc", }, + {}, +}; + +static int __init bamboo_device_probe(void) +{ + if (!machine_is(bamboo)) + return 0; + + of_platform_bus_probe(NULL, bamboo_of_bus, NULL); + + return 0; +} +device_initcall(bamboo_device_probe); + +static int __init bamboo_probe(void) +{ + unsigned long root = of_get_flat_dt_root(); + + if (!of_flat_dt_is_compatible(root, "amcc,bamboo")) + return 0; + + return 1; +} + +static void __init bamboo_setup_arch(void) +{ +} + +define_machine(bamboo) { + .name = "Bamboo", + .probe = bamboo_probe, + .setup_arch = bamboo_setup_arch, + .progress = udbg_progress, + .init_IRQ = uic_init_tree, + .get_irq = uic_get_irq, + .restart = ppc44x_reset_system, + .calibrate_decr = generic_calibrate_decr, +}; -- ^ permalink raw reply [flat|nested] 22+ messages in thread
* [patch 14/14] Bamboo zImage wrapper 2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer ` (12 preceding siblings ...) 2007-07-17 18:16 ` [patch 13/14] Bamboo board support Josh Boyer @ 2007-07-17 18:16 ` Josh Boyer 13 siblings, 0 replies; 22+ messages in thread From: Josh Boyer @ 2007-07-17 18:16 UTC (permalink / raw) To: linuxppc-dev Add a bootwrapper for Bamboo Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> --- arch/powerpc/boot/44x.h | 1 arch/powerpc/boot/Makefile | 5 - arch/powerpc/boot/bamboo.c | 126 ++++++++++++++++++++++++++++++++++++ arch/powerpc/boot/dcr.h | 11 +++ arch/powerpc/boot/treeboot-bamboo.c | 27 +++++++ 5 files changed, 168 insertions(+), 2 deletions(-) --- linux-2.6.orig/arch/powerpc/boot/Makefile +++ linux-2.6/arch/powerpc/boot/Makefile @@ -44,10 +44,10 @@ $(addprefix $(obj)/,$(zlib) gunzip_util. src-wlib := string.S crt0.S stdio.c main.c flatdevtree.c flatdevtree_misc.c \ ns16550.c serial.c simple_alloc.c div64.S util.S \ gunzip_util.c elf_util.c $(zlib) devtree.c oflib.c ofconsole.c \ - 4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c + 4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c bamboo.c src-plat := of.c cuboot-83xx.c cuboot-85xx.c holly.c \ cuboot-ebony.c treeboot-ebony.c prpmc2800.c \ - ps3-head.S ps3-hvcall.S ps3.c treeboot-walnut.c + ps3-head.S ps3-hvcall.S ps3.c treeboot-walnut.c treeboot-bamboo.c src-boot := $(src-wlib) $(src-plat) empty.c src-boot := $(addprefix $(obj)/, $(src-boot)) @@ -143,6 +143,7 @@ image-$(CONFIG_PPC_83xx) += cuImage.83x image-$(CONFIG_PPC_85xx) += cuImage.85xx image-$(CONFIG_EBONY) += treeImage.ebony cuImage.ebony image-$(CONFIG_WALNUT) += treeImage.walnut +image-$(CONFIG_BAMBOO) += treeImage.bamboo endif # For 32-bit powermacs, build the COFF and miboot images --- /dev/null +++ linux-2.6/arch/powerpc/boot/bamboo.c @@ -0,0 +1,126 @@ +/* + * Copyright IBM Corporation, 2007 + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * Based on ebony wrapper: + * Copyright 2007 David Gibson, IBM Corporation. + * + * Clocking code based on code by: + * Stefan Roese <sr@denx.de> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; version 2 of the License + */ +#include <stdarg.h> +#include <stddef.h> +#include "types.h" +#include "elf.h" +#include "string.h" +#include "stdio.h" +#include "page.h" +#include "ops.h" +#include "dcr.h" +#include "4xx.h" +#include "44x.h" + +extern char _dtb_start[]; +extern char _dtb_end[]; + +#define SPRN_CCR1 0x378 +void ibm440ep_fixup_clocks(unsigned int sysclk, unsigned int ser_clk) +{ + u32 cpu, plb, opb, ebc, tb, uart0, m, vco; + u32 reg; + u32 fwdva, fwdvb, fbdv, lfbdv, opbdv0, perdv0, spcid0, prbdv0, tmp; + + mtdcr(DCRN_CPR0_ADDR, CPR0_PLLD0); + reg = mfdcr(DCRN_CPR0_DATA); + tmp = (reg & 0x000F0000) >> 16; + fwdva = tmp ? tmp : 16; + tmp = (reg & 0x00000700) >> 8; + fwdvb = tmp ? tmp : 8; + tmp = (reg & 0x1F000000) >> 24; + fbdv = tmp ? tmp : 32; + lfbdv = (reg & 0x0000007F); + + mtdcr(DCRN_CPR0_ADDR, CPR0_OPBD0); + reg = mfdcr(DCRN_CPR0_DATA); + tmp = (reg & 0x03000000) >> 24; + opbdv0 = tmp ? tmp : 4; + + mtdcr(DCRN_CPR0_ADDR, CPR0_PERD0); + reg = mfdcr(DCRN_CPR0_DATA); + tmp = (reg & 0x07000000) >> 24; + perdv0 = tmp ? tmp : 8; + + mtdcr(DCRN_CPR0_ADDR, CPR0_PRIMBD0); + reg = mfdcr(DCRN_CPR0_DATA); + tmp = (reg & 0x07000000) >> 24; + prbdv0 = tmp ? tmp : 8; + + mtdcr(DCRN_CPR0_ADDR, CPR0_SCPID); + reg = mfdcr(DCRN_CPR0_DATA); + tmp = (reg & 0x03000000) >> 24; + spcid0 = tmp ? tmp : 4; + + /* Calculate M */ + mtdcr(DCRN_CPR0_ADDR, CPR0_PLLC0); + reg = mfdcr(DCRN_CPR0_DATA); + tmp = (reg & 0x03000000) >> 24; + if (tmp == 0) { /* PLL output */ + tmp = (reg & 0x20000000) >> 29; + if (!tmp) /* PLLOUTA */ + m = fbdv * lfbdv * fwdva; + else + m = fbdv * lfbdv * fwdvb; + } + else if (tmp == 1) /* CPU output */ + m = fbdv * fwdva; + else + m = perdv0 * opbdv0 * fwdvb; + + vco = (m * sysclk) + (m >> 1); + cpu = vco / fwdva; + plb = vco / fwdvb / prbdv0; + opb = plb / opbdv0; + ebc = plb / perdv0; + + /* FIXME */ + uart0 = ser_clk; + + /* Figure out timebase. Either CPU or default TmrClk */ + asm volatile ( + "mfspr %0,%1\n" + : + "=&r"(reg) : "i"(SPRN_CCR1)); + if (reg & 0x0080) + tb = 25000000; /* TmrClk is 25MHz */ + else + tb = cpu; + + dt_fixup_cpu_clocks(cpu, tb, 0); + dt_fixup_clock("/plb", plb); + dt_fixup_clock("/plb/opb", opb); + dt_fixup_clock("/plb/opb/ebc", ebc); + dt_fixup_clock("/plb/opb/serial@ef600300", uart0); + dt_fixup_clock("/plb/opb/serial@ef600400", uart0); + dt_fixup_clock("/plb/opb/serial@ef600500", uart0); + dt_fixup_clock("/plb/opb/serial@ef600600", uart0); +} + +static void bamboo_fixups(void) +{ + unsigned long sysclk = 33333333; + ibm440ep_fixup_clocks(sysclk, 11059200); + ibm4xx_fixup_memsize(); + ibm4xx_reset_eth((u32 *)0xef600e00, (u32 *)0xef600f00); +} + +void bamboo_init(void) +{ + platform_ops.fixups = bamboo_fixups; + platform_ops.exit = ibm44x_dbcr_reset; + ft_init(_dtb_start, 0, 32); + serial_console_init(); +} --- linux-2.6.orig/arch/powerpc/boot/44x.h +++ linux-2.6/arch/powerpc/boot/44x.h @@ -11,5 +11,6 @@ #define _PPC_BOOT_44X_H_ void ebony_init(void *mac0, void *mac1); +void bamboo_init(void); #endif /* _PPC_BOOT_44X_H_ */ --- /dev/null +++ linux-2.6/arch/powerpc/boot/treeboot-bamboo.c @@ -0,0 +1,27 @@ +/* + * Copyright IBM Corporation, 2007 + * Josh Boyer <jwboyer@linux.vnet.ibm.com> + * + * Based on ebony wrapper: + * Copyright 2007 David Gibson, IBM Corporation. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; version 2 of the License + */ +#include "ops.h" +#include "stdio.h" +#include "44x.h" + +extern char _end[]; + +BSS_STACK(4096); + +void platform_init(void) +{ + unsigned long end_of_ram = 0x8000000; + unsigned long avail_ram = end_of_ram - (unsigned long)_end; + + simple_alloc_init(_end, avail_ram, 32, 64); + bamboo_init(); +} --- linux-2.6.orig/arch/powerpc/boot/dcr.h +++ linux-2.6/arch/powerpc/boot/dcr.h @@ -123,4 +123,15 @@ static const unsigned long sdram_bxcr[] #define DCRN_MAL0_CFG 0x180 +/* 440EP Clock/Power-on Reset regs */ +#define DCRN_CPR0_ADDR 0xc +#define DCRN_CPR0_DATA 0xd +#define CPR0_PLLD0 0x60 +#define CPR0_OPBD0 0xc0 +#define CPR0_PERD0 0xe0 +#define CPR0_PRIMBD0 0xa0 +#define CPR0_SCPID 0x120 +#define CPR0_PLLC0 0x40 + + #endif /* _PPC_BOOT_DCR_H_ */ -- ^ permalink raw reply [flat|nested] 22+ messages in thread
[parent not found: <41060.0659474314$1184697204@news.gmane.org>]
* Re: [patch 00/14] Current 4xx patch series [not found] <41060.0659474314$1184697204@news.gmane.org> @ 2007-08-02 20:57 ` Hollis Blanchard 2007-08-02 21:39 ` Josh Boyer 0 siblings, 1 reply; 22+ messages in thread From: Hollis Blanchard @ 2007-08-02 20:57 UTC (permalink / raw) To: linuxppc-dev On Tue, 17 Jul 2007 13:15:47 -0500, Josh Boyer wrote: > For those interested, here's my current 4xx patch series. There are a few > cleanups as a pre-requisite for 40x support, some minimal Walnut support, and > another round of Bamboo patches. These are all based off of Paul's current > tree. Bamboo is booting for me with your patches. Let's get them in soon... > Ethernet for 4xx in general is still provided by the out-of-tree emac rewrite > that Ben and David have poked at. If it doesn't get merged soon, I'll take > a look at getting it working again. Please! -- Hollis Blanchard IBM Linux Technology Center ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [patch 00/14] Current 4xx patch series 2007-08-02 20:57 ` [patch 00/14] Current 4xx patch series Hollis Blanchard @ 2007-08-02 21:39 ` Josh Boyer 2007-08-02 22:38 ` Benjamin Herrenschmidt 0 siblings, 1 reply; 22+ messages in thread From: Josh Boyer @ 2007-08-02 21:39 UTC (permalink / raw) To: Hollis Blanchard; +Cc: linuxppc-dev On Thu, 2 Aug 2007 20:57:26 +0000 (UTC) Hollis Blanchard <hollisb@us.ibm.com> wrote: > On Tue, 17 Jul 2007 13:15:47 -0500, Josh Boyer wrote: > > > For those interested, here's my current 4xx patch series. There are a few > > cleanups as a pre-requisite for 40x support, some minimal Walnut support, and > > another round of Bamboo patches. These are all based off of Paul's current > > tree. > > Bamboo is booting for me with your patches. Let's get them in soon... I plan on submitting a series to Paul tomorrow-ish for 2.6.24. Too late for 2.6.23. > > Ethernet for 4xx in general is still provided by the out-of-tree emac rewrite > > that Ben and David have poked at. If it doesn't get merged soon, I'll take > > a look at getting it working again. > > Please! Someone brought up the fact that the EMAC rewrite is mostly just changing probing code and the guts are still similar to the current EMAC driver. I haven't really looked into it yet, but if that's true, I'd be curious as to why it was done that way. Either way, I'm hoping we can get something into 2.6.24. josh ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [patch 00/14] Current 4xx patch series 2007-08-02 21:39 ` Josh Boyer @ 2007-08-02 22:38 ` Benjamin Herrenschmidt 2007-08-03 0:26 ` Josh Boyer 0 siblings, 1 reply; 22+ messages in thread From: Benjamin Herrenschmidt @ 2007-08-02 22:38 UTC (permalink / raw) To: Josh Boyer; +Cc: linuxppc-dev, Hollis Blanchard On Thu, 2007-08-02 at 16:39 -0500, Josh Boyer wrote: > > Someone brought up the fact that the EMAC rewrite is mostly just > changing probing code and the guts are still similar to the current > EMAC driver. I haven't really looked into it yet, but if that's true, > I'd be curious as to why it was done that way. Ask :-) What specifically do you want to know ? Ben. ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [patch 00/14] Current 4xx patch series 2007-08-02 22:38 ` Benjamin Herrenschmidt @ 2007-08-03 0:26 ` Josh Boyer 2007-08-03 0:29 ` Benjamin Herrenschmidt 0 siblings, 1 reply; 22+ messages in thread From: Josh Boyer @ 2007-08-03 0:26 UTC (permalink / raw) To: Benjamin Herrenschmidt; +Cc: linuxppc-dev, Hollis Blanchard On Fri, Aug 03, 2007 at 08:38:16AM +1000, Benjamin Herrenschmidt wrote: > On Thu, 2007-08-02 at 16:39 -0500, Josh Boyer wrote: > > > > Someone brought up the fact that the EMAC rewrite is mostly just > > changing probing code and the guts are still similar to the current > > EMAC driver. I haven't really looked into it yet, but if that's true, > > I'd be curious as to why it was done that way. > > Ask :-) What specifically do you want to know ? :) Are the guts mostly the same, and if so why wasn't the existing driver just modified to do the device tree probing, perhaps in addition to the arch/ppc method? I can answer the "are they similar" myself with inspection, but I just haven't found the time yet. So just some history about the patch would be good in general I think. josh ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [patch 00/14] Current 4xx patch series 2007-08-03 0:26 ` Josh Boyer @ 2007-08-03 0:29 ` Benjamin Herrenschmidt 0 siblings, 0 replies; 22+ messages in thread From: Benjamin Herrenschmidt @ 2007-08-03 0:29 UTC (permalink / raw) To: Josh Boyer; +Cc: linuxppc-dev, Hollis Blanchard On Thu, 2007-08-02 at 19:26 -0500, Josh Boyer wrote: > On Fri, Aug 03, 2007 at 08:38:16AM +1000, Benjamin Herrenschmidt wrote: > > On Thu, 2007-08-02 at 16:39 -0500, Josh Boyer wrote: > > > > > > Someone brought up the fact that the EMAC rewrite is mostly just > > > changing probing code and the guts are still similar to the current > > > EMAC driver. I haven't really looked into it yet, but if that's true, > > > I'd be curious as to why it was done that way. > > > > Ask :-) What specifically do you want to know ? > > :) > > Are the guts mostly the same, and if so why wasn't the existing driver just > modified to do the device tree probing, perhaps in addition to the arch/ppc > method? > > I can answer the "are they similar" myself with inspection, but I just haven't > found the time yet. So just some history about the patch would be good in > general I think. Guts are the same with subtle differences :-) The main reason not to modify the existing one was because I wanted to be conservative and not take any chance at breaking arch/ppc. Also, we did that in earlier versions internally (have both OCP and device-tree probing) and it's a terrible mess. Since arch/ppc is doomed, I wanted to avoid designing something that can do both for no real benefit. There are other subtle differences, such as the locking of the MDIO accesses, and locking bits and pieces in general (EMAC wasn't tested in SMP environments, and while it was tested with preempt, there are a few subtle differences and issues that went unnoticed). I also haven't brought back the workarounds for the loss of the Rx clock with some PHYs at this stage. I need to get my hand on HW that has this issue to be able to decide what to do I believe. The thing is, global whacking of clock control registers like the old driver does is a bit scary, totally per-chip-type, and requires locking vs. other parts of the system that may want to access the same registers etc... However, some of the chip folks told me it might be possible instead to just use loopback mode when there is no link. So I want to investigate that possibility first, but for that, I need HW that has the symptoms and so far, I think I don't. Finally, we still need to add in proper DMA unmapping. The current driver never unmaps which is a problem on Axon when using the iommu. Cheers, Ben. ^ permalink raw reply [flat|nested] 22+ messages in thread
end of thread, other threads:[~2007-08-03 0:34 UTC | newest]
Thread overview: 22+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-07-17 18:15 [patch 00/14] Current 4xx patch series Josh Boyer
2007-07-17 18:15 ` [patch 01/14] Use resource_size_t for serial port IO addresses Josh Boyer
2007-07-17 18:15 ` [patch 02/14] Rename 4xx paths to 40x Josh Boyer
2007-07-18 3:26 ` David Gibson
2007-07-17 18:15 ` [patch 03/14] 4xx Kconfig cleanup Josh Boyer
2007-07-17 18:15 ` [patch 04/14] 4xx bootwrapper reworks Josh Boyer
2007-07-17 18:15 ` [patch 05/14] 40x MMU Josh Boyer
2007-07-18 3:38 ` David Gibson
2007-07-17 18:15 ` [patch 06/14] 40x decrementer fixes Josh Boyer
2007-07-17 18:15 ` [patch 07/14] Fix 40x build Josh Boyer
2007-07-17 18:15 ` [patch 08/14] Walnut DTS Josh Boyer
2007-07-17 18:15 ` [patch 09/14] Walnut defconfig Josh Boyer
2007-07-17 18:15 ` [patch 10/14] Walnut board support Josh Boyer
2007-07-17 18:15 ` [patch 11/14] Walnut zImage wrapper Josh Boyer
2007-07-17 18:15 ` [patch 12/14] Bamboo DTS Josh Boyer
2007-07-17 18:16 ` [patch 13/14] Bamboo board support Josh Boyer
2007-07-17 18:16 ` [patch 14/14] Bamboo zImage wrapper Josh Boyer
[not found] <41060.0659474314$1184697204@news.gmane.org>
2007-08-02 20:57 ` [patch 00/14] Current 4xx patch series Hollis Blanchard
2007-08-02 21:39 ` Josh Boyer
2007-08-02 22:38 ` Benjamin Herrenschmidt
2007-08-03 0:26 ` Josh Boyer
2007-08-03 0:29 ` Benjamin Herrenschmidt
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).