From: Grant Likely <grant.likely@secretlab.ca>
To: Dragos Carp <dragos.carp@toptica.com>,
linux-kernel@vger.kernel.org, dbrownell@users.sourceforge.net,
domen.puncer@telargo.com, linuxppc-dev@ozlabs.org
Subject: [PATCH] mpc5200: psc-spi driver must not touch port_config or cdm registers
Date: Tue, 23 Oct 2007 21:39:35 -0600 [thread overview]
Message-ID: <20071024033457.8657.8708.stgit@trillian.cg.shawcable.net> (raw)
From: Grant Likely <grant.likely@secretlab.ca>
port_config and the cdm are the responsibility of firmware; and if
firmware doesn't set it up correctly, it should be fixed up by
platform code on a per-board basis because it's a property of the
board.
Drivers should never touch these registers. They are completely
unprotected and the platform may do odd things with them that the
driver must not interfere with.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
Domen, Dragos; can you please check your usage of this driver. None of
the in-tree board ports use it as-is, but they are of course just a
device tree change away from being usable on the lite5200b.
Board ports that use it need to be modified to make the cdm/port_config
changes in firmware (prefered) or in arch/powerpc/platforms/52xx/<board>.c
Cheers,
g.
drivers/spi/mpc52xx_psc_spi.c | 77 +----------------------------------------
1 files changed, 2 insertions(+), 75 deletions(-)
diff --git a/drivers/spi/mpc52xx_psc_spi.c b/drivers/spi/mpc52xx_psc_spi.c
index 7051e6c..ec3a618 100644
--- a/drivers/spi/mpc52xx_psc_spi.c
+++ b/drivers/spi/mpc52xx_psc_spi.c
@@ -328,78 +328,15 @@ static void mpc52xx_psc_spi_cleanup(struct spi_device *spi)
kfree(spi->controller_state);
}
-static int mpc52xx_psc_spi_port_config(int psc_id, struct mpc52xx_psc_spi *mps)
+static void mpc52xx_psc_spi_config(int psc_id, struct mpc52xx_psc_spi *mps)
{
- struct mpc52xx_cdm __iomem *cdm;
- struct mpc52xx_gpio __iomem *gpio;
struct mpc52xx_psc __iomem *psc = mps->psc;
- u32 ul;
u32 mclken_div;
- int ret = 0;
-
-#if defined(CONFIG_PPC_MERGE)
- cdm = mpc52xx_find_and_map("mpc5200-cdm");
- gpio = mpc52xx_find_and_map("mpc5200-gpio");
-#else
- cdm = ioremap(MPC52xx_PA(MPC52xx_CDM_OFFSET), MPC52xx_CDM_SIZE);
- gpio = ioremap(MPC52xx_PA(MPC52xx_GPIO_OFFSET), MPC52xx_GPIO_SIZE);
-#endif
- if (!cdm || !gpio) {
- printk(KERN_ERR "Error mapping CDM/GPIO\n");
- ret = -EFAULT;
- goto unmap_regs;
- }
/* default sysclk is 512MHz */
mclken_div = 0x8000 |
(((mps->sysclk ? mps->sysclk : 512000000) / MCLK) & 0x1FF);
- switch (psc_id) {
- case 1:
- ul = in_be32(&gpio->port_config);
- ul &= 0xFFFFFFF8;
- ul |= 0x00000006;
- out_be32(&gpio->port_config, ul);
- out_be16(&cdm->mclken_div_psc1, mclken_div);
- ul = in_be32(&cdm->clk_enables);
- ul |= 0x00000020;
- out_be32(&cdm->clk_enables, ul);
- break;
- case 2:
- ul = in_be32(&gpio->port_config);
- ul &= 0xFFFFFF8F;
- ul |= 0x00000060;
- out_be32(&gpio->port_config, ul);
- out_be16(&cdm->mclken_div_psc2, mclken_div);
- ul = in_be32(&cdm->clk_enables);
- ul |= 0x00000040;
- out_be32(&cdm->clk_enables, ul);
- break;
- case 3:
- ul = in_be32(&gpio->port_config);
- ul &= 0xFFFFF0FF;
- ul |= 0x00000600;
- out_be32(&gpio->port_config, ul);
- out_be16(&cdm->mclken_div_psc3, mclken_div);
- ul = in_be32(&cdm->clk_enables);
- ul |= 0x00000080;
- out_be32(&cdm->clk_enables, ul);
- break;
- case 6:
- ul = in_be32(&gpio->port_config);
- ul &= 0xFF8FFFFF;
- ul |= 0x00700000;
- out_be32(&gpio->port_config, ul);
- out_be16(&cdm->mclken_div_psc6, mclken_div);
- ul = in_be32(&cdm->clk_enables);
- ul |= 0x00000010;
- out_be32(&cdm->clk_enables, ul);
- break;
- default:
- ret = -EINVAL;
- goto unmap_regs;
- }
-
/* Reset the PSC into a known state */
out_8(&psc->command, MPC52xx_PSC_RST_RX);
out_8(&psc->command, MPC52xx_PSC_RST_TX);
@@ -421,14 +358,6 @@ static int mpc52xx_psc_spi_port_config(int psc_id, struct mpc52xx_psc_spi *mps)
out_8(&psc->ctlr, 0x84);
mps->bits_per_word = 8;
-
-unmap_regs:
- if (cdm)
- iounmap(cdm);
- if (gpio)
- iounmap(gpio);
-
- return ret;
}
static irqreturn_t mpc52xx_psc_spi_isr(int irq, void *dev_id)
@@ -493,9 +422,7 @@ static int __init mpc52xx_psc_spi_do_probe(struct device *dev, u32 regaddr,
if (ret)
goto free_master;
- ret = mpc52xx_psc_spi_port_config(master->bus_num, mps);
- if (ret < 0)
- goto free_irq;
+ mpc52xx_psc_spi_config(master->bus_num, mps);
spin_lock_init(&mps->lock);
init_completion(&mps->done);
next reply other threads:[~2007-10-24 3:41 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-10-24 3:39 Grant Likely [this message]
2007-10-24 5:01 ` [PATCH] mpc5200: psc-spi driver must not touch port_config or cdm registers Domen Puncer
2007-10-24 5:27 ` Grant Likely
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20071024033457.8657.8708.stgit@trillian.cg.shawcable.net \
--to=grant.likely@secretlab.ca \
--cc=dbrownell@users.sourceforge.net \
--cc=domen.puncer@telargo.com \
--cc=dragos.carp@toptica.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).